Revell 63 CHEVY IMPALA SS 2 IN 1 Manuel utilisateur
- Taper
- Manuel utilisateur
DECAL PLACEMENT
12
Semi Gloss Black
Flat Red
Gloss Blue Pearl
Chevy Engine Red
Gloss White
Aluminum
Silver
Steel
Turn Signal Amber
This paint guide is provided to complete this kit
as shown on the box.
Ce guide de peintures est fourni pour reproduire le modèle
réduit qui apparaît sur la boîte.
Noir satiné
Rouge mat
Bleu nacré brilliant
Rouge De Moteur De Chevy
Blanc brillant
Aluminum
Argent brillant metallisé
Acier
Ambre
* Study the assembly drawings.
* Each plastic part is identified by a number.
* In the assembly drawings, some parts will be
marked by a star (★) to indicate chrome
plated plastic.
* For better paint and decal adhesion, wash
the plastic parts in a mild detergent solution.
Rinse and let air dry.
* Check the fit of each piece before
cementing in place.
* Use only cement for polystyrene plastic.
* Scrape plating and paint from areas
to be cemented.
* Allow paint to dry thoroughly before
handling parts.
* Any unused parts may be discarded.
DECAL APPLICATION INSTRUCTIONS
1. Cut desired decal from sheet.
2. Dip decal in water for a few seconds.
3. Place wet decal on paper towel.
4. Wait until decal is movable on paper backing.
5. Place decal in position on model, face up and
slide backing away.
6. Press out air bubbles with a soft damp cloth.
7. Milkiness that may appear is for better decal
adhesion and will dry clear. Wipe away any
excess adhesive.
8. Do not touch decal until fully dry.
9. Allow the decals 48 hours to dry before
applying clear coat.
NOTE: Decals are compatible with
setting solutions or solvents.
READ THIS BEFORE YOU BEGIN LIRE CE QUI SUIT AVANT DE COMMENCER
* Etudier les schémas de montage.
* Chaque pièce en plastique est identifiée par un numéro.
* Sur les schémas de montage, certaines pièces sont
marquées d'une étoile (★) pour indiquer qu'elles sont en
plastique chromé.
* Pour une meilleure prise de la peinture et des autocollants,
laver les pièces en plastique avec une solution détergente peu
concentrée. Les rincer et les laisser sécher à l'air.
* Vérifier que chaque pièce s'ajuste bien avant
de la coller en place.
* N'utiliser que de la colle pour polystyrène.
* Gratter les parties à coller pour enlever le chrome et la peinture.
* Laisser la peinture bien sécher avant de manipuler les pièces.
* Toute pièce inutilisée peut être jetée.
DIRECTIVES D'APPLICATION DES AUTOCOLLANTS
1. Découper l'autocollant désiré de la feuille.
2. Tremper l'autocollant dans de l'eau pendant quelques secondes.
3. Placer l'autocollant mouillé sur une serviette en papier.
4. Attendez que l'autocollant puisse être déplacé sur son
support en papier.
5. Mettre l'autocollant en position sur le modèle face sur
le dessus et faire glisser le support pour l'enlever.
6. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air.
7. La substance laiteuse qui peut apparaître est destinée à
améliorer l'adhésion de l'autocollant et devient incolore au
séchage. Essuyer pour enlever tout excédent d'adhésif.
8. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec.
9. Laisser l'autocollant sécher pendant 48 heures avant
d'appliquer une couche transparente.
REMARQUE: Les autocollants sont compatibles avec
les solutions de fixage ou les solvants.
'63 CHEVY
® IMPALA™ SS
™ 2 'N 1
KIT 4278 85427800200
If you have any questions or comments, call our hotline at: (800) 833-3570
or, please write to:
Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007
Be sure to include the plan number (85427800200), part number, description, your return address and phone number.
Visit our website: www.revell.com
Revell Inc Elk Grove Village, IL. Copyright © 2010. All rights reserved.
Kit 4278 - Page 8
* REPEAT SEVERAL TIMES
* A REPETER PLUSIEURS FOIS
* CEMENT TOGETHER
* A COLLER
* REMOVE AND THROW AWAY
* A RETIRER ET JETER
* DO NOT CEMENT
* NE PAS COLLER
* DECAL
* DECAL COMANIE
* ASSEMBLY CAUTION
*ATTENTION D ASSEMBLEE
* OPTIONAL PARTS
* PIECES EN OPTION
* REPEAT PROCEDURE
* R E P E T E Z L E P R O C E D E
`` ` ` `
While locked in a battle for the
top spot in the annual sale races,
Chevrolet® gave it's popular Impala™
good-looking angular lines for '63 as
well as carrying over the "convert-
ible look" two door hardtop body
from 1962. Decades later, the 1963
Chevy® remains one of the most
desired subjects among both the
restoration and custom car crowd.
Your Revell model features an
opening hood and trunk plus mul-
tiple suspension positions, option-
al factory stock wheels and tires
or custom wheels with low profile
tires and decals with both facto-
ry stock and custom graphics.
RADIATOR ASSEMBLY
2
ENGINE ASSEMBLY
1SUSPENSION ASSEMBLY CONTINUED
9
FRONT ASSEMBLY
10
Kit 4278 - Page 2 Kit 4278 - Page 7
RAISED RIDE HEIGHT
USE WITH #33 CUSTOM
AXLE SPACER
10
RIGHT
ENGINE BLOCK
CHEVY ENGINE RED
9
LEFT
ENGINE BLOCK
CHEVY ENGINE RED
ALUMINUM
12
ENGINE TOP
CHEVY ENGINE RED
STEEL
SEMI GLOSS
BLACK
13
ENGINE COVER
CHEVY ENGINE RED
DECAL
5 or 6
(STOCK)
DECAL
20
(CUSTOM)
DECAL
21
(CUSTOM)
DECAL
22
DECAL
5 or 6
(STOCK)
★47
ROCKER COVER
CHROME
(CHEVY ENGINE RED)
★47
ROCKER COVER
CHROME
(CHEVY ENGINE RED)
SEMI GLOSS
BLACK
11
OIL PAN
CHEVY ENGINE RED
GLOSS BLUE
15
EXHAUST
MANIFOLD
STEEL
15
EXHAUST
MANIFOLD
STEEL
80
STOCK AIR
CLEANER
SEMI GLOSS BLACK
17
FAN
SEMI GLOSS BLACK
DECAL
4
✱✱
✱
✱
✱
✱
COMPLETED
ENGINE
ASSEMBLY
41
FRAME
SEMI GLOSS BLACK
★49
ALTERNATOR
CHROME
14
FAN BELT
SEMI GLOSS
BLACK
PAINT PULLEYS
ALUMINUM
5
FAN SHROUD
TOP
SEMI GLOSS BLACK
6
FAN SHROUD
BOTTOM
SEMI GLOSS BLACK
7
RADIATOR
SEMI GLOSS BLACK
60
STOCK SHOCKS
SEMI GLOSS BLACK
34
SHORT SHOCKS
SEMI GLOSS BLACK
62
LONG SHOCKS
SEMI GLOSS BLACK
58
HEADLIGHTS
CLEAR
★44
GRILLE / BUMPER
CHROME
★45
HOOD TRIM
CHROME
★56
SIDE VIEW MIRROR
CHROME
★48
CUSTOM
AIR CLEANER
CHROME
WHITE
REAR ASSEMBLY
11
SILVER
(BODY COLOR)
★46
REAR BUMPER
CHROME
59
TAILLIGHTS
TRANSPARENT RED
LOWERED RIDE
HEIGHT
STOCK RIDE
HEIGHT
EXHAUST ASSEMBLY
8
REAR SUSPENSION ASSEMBLY
9
RADIATOR ASSEMBLY CONTINUED
2
FRONT SUSPENSION ASSEMBLY
3
WHEEL ASSEMBLY
4
Kit 4278 - Page 3Kit 4278 - Page 6
STOCK
RAISED RIDE HEIGHT
USES PARTS WITH #37
CUSTOM SUSPENSION
SHOWN IN STEP #3
UPPER RADIATOR
HOSE LOCATES TO
HOLE IN RADIATOR
8
LOWER
RADIATOR HOSE
SEMI GLOSS BLACK
FRAME
TURNED
OVER
37
CUSTOM FRONT
SUSPENSION
SEMI GLOSS BLACK
38
STOCK FRONT
SUSPENSION
SEMI GLOSS BLACK
★77
OUTER
WHEEL
CHROME
78
WHEEL
RETAINER
★100
CUSTOM
WHEEL
CHROME
101
DISK
BRAKE
STEEL
29
LEFT EXHAUST
ALUMINUM
30
RIGHT EXHAUST
ALUMINUM
✱
✱
✱
✱
✱
✱
✱
33
CUSTOM AXLE
SPACERS
SEMI GLOSS BLACK
32
DIFFERENTIAL
SEMI GLOSS BLACK
31
REAR AXLE
SEMI GLOSS BLACK
METAL AXLE PIN
METAL AXLE PIN
TIRE
TIRE
CUSTOM
RAISED RIDE HEIGHT
POSITION
LOWERED RIDE
HEIGHT POSITION
OPTIONAL RIDE HEIGHT
STOCK RIDE HEIGHT
CUSTOM
STOCK
STOCK RIDE HEIGHT
POSITION
28
DRIVESHAFT
SEMI GLOSS BLACK
76
RIGHT STOCK
AXLE SPACER
SEMI GLOSS BLACK
75
LEFT STOCK
AXLE SPACER
SEMI GLOSS BLACK
METAL AXLE PINS
METAL AXLE PINS
DECAL
17
(18 REAR)
FRONT WHEEL ASSEMBLYCONTINUED
4
INTERIOR ASSEMBLY
5
INTERIOR ASSEMBLY CONTINUED
5
WINDOW / FIREWALL ASSEMBLY
6
Kit 4278 - Page 4 Kit 4278 - Page 5
NOTE: REMOVE SHADED AREA AT DEPRESSED LINE
61
REAR WINDOW
CLEAR
★51
REAR VIEW
MIRROR
CHROME
57
WINDSHIELD
CLEAR
3
TRUNK
BODY
COLOR
FIRST
FIRST
SECOND
SECOND
1
BODY
BODY COLOR
DECAL
11
2
HOOD
BODY COLOR
4
FIREWALL
SEMI GLOSS BLACK
SEMI GLOSS BLACK
25
STEERING
COLUMN
FLAT RED
(SILVER-CUSTOM) SILVER
STALKS
24
DASHBOARD
FLAT RED
(SILVER-CUSTOM)
SILVER DETAILS PEDALS
SEMI GLOSS BLACK
DECAL
1
DECAL
2
26
STEERING WHEEL
FLAT RED
(SILVER-CUSTOM) (PAINT LIGHT
SHADED AREA SILVER)
27
CHASSIS PAN
SEMI GLOSS BLACK
22
SEAT BACK
FLAT RED
(SILVER-CUSTOM)
21
FRONT SEAT
FLAT RED
(SILVER-CUSTOM)
79
STOCK
SPARE WHEEL
SEMI GLOSS BLACK
STOCK TIRE
23
REAR
SEAT BACK
FLAT RED
(SILVER-CUSTOM)
SILVER
(STOCK)
NOTE: REMOVE SHADED AREA AT DEPRESSED LINES
18
INTERIOR FLOOR
FLAT RED
(SILVER-CUSTOM)
20
RIGHT
DOOR PANEL
FLAT RED
(SILVER-CUSTOM) PAINT SHADED DETAIL
AREAS SILVER (REPEAT FOR DRIVER’S
SIDE)
★50
SHIFTER
CHROME
SILVER
(STOCK)
19
LEFT
DOOR PANEL
FLAT RED
(SILVER-CUSTOM)
INTERIOR / BODY / FRAME ASSEMBLY
7
FIRST
STOCK
CUSTOM
METAL AXLE PINMETAL AXLE PIN
RAISED RIDE HEIGHT
POSITION
STOCK RIDE HEIGHT
POSITION
LOWERED RIDE
HEIGHT POSITION
37
CUSTOM FRONT
SUSPENSION
38
STOCK FRONT
SUSPENSION
DECAL
3
DECAL
14
DECAL
15
DECAL
12
DECAL
12
DECAL
16
DECAL
13
DECAL
13
FRONT WHEEL ASSEMBLYCONTINUED
4
INTERIOR ASSEMBLY
5
INTERIOR ASSEMBLY CONTINUED
5
WINDOW / FIREWALL ASSEMBLY
6
Kit 4278 - Page 4 Kit 4278 - Page 5
NOTE: REMOVE SHADED AREA AT DEPRESSED LINE
61
REAR WINDOW
CLEAR
★51
REAR VIEW
MIRROR
CHROME
57
WINDSHIELD
CLEAR
3
TRUNK
BODY
COLOR
FIRST
FIRST
SECOND
SECOND
1
BODY
BODY COLOR
DECAL
11
2
HOOD
BODY COLOR
4
FIREWALL
SEMI GLOSS BLACK
SEMI GLOSS BLACK
25
STEERING
COLUMN
FLAT RED
(SILVER-CUSTOM) SILVER
STALKS
24
DASHBOARD
FLAT RED
(SILVER-CUSTOM)
SILVER DETAILS PEDALS
SEMI GLOSS BLACK
DECAL
1
DECAL
2
26
STEERING WHEEL
FLAT RED
(SILVER-CUSTOM) (PAINT LIGHT
SHADED AREA SILVER)
27
CHASSIS PAN
SEMI GLOSS BLACK
22
SEAT BACK
FLAT RED
(SILVER-CUSTOM)
21
FRONT SEAT
FLAT RED
(SILVER-CUSTOM)
79
STOCK
SPARE WHEEL
SEMI GLOSS BLACK
STOCK TIRE
23
REAR
SEAT BACK
FLAT RED
(SILVER-CUSTOM)
SILVER
(STOCK)
NOTE: REMOVE SHADED AREA AT DEPRESSED LINES
18
INTERIOR FLOOR
FLAT RED
(SILVER-CUSTOM)
20
RIGHT
DOOR PANEL
FLAT RED
(SILVER-CUSTOM) PAINT SHADED DETAIL
AREAS SILVER (REPEAT FOR DRIVER’S
SIDE)
★50
SHIFTER
CHROME
SILVER
(STOCK)
19
LEFT
DOOR PANEL
FLAT RED
(SILVER-CUSTOM)
INTERIOR / BODY / FRAME ASSEMBLY
7
FIRST
STOCK
CUSTOM
METAL AXLE PINMETAL AXLE PIN
RAISED RIDE HEIGHT
POSITION
STOCK RIDE HEIGHT
POSITION
LOWERED RIDE
HEIGHT POSITION
37
CUSTOM FRONT
SUSPENSION
38
STOCK FRONT
SUSPENSION
DECAL
3
DECAL
14
DECAL
15
DECAL
12
DECAL
12
DECAL
16
DECAL
13
DECAL
13
EXHAUST ASSEMBLY
8
REAR SUSPENSION ASSEMBLY
9
RADIATOR ASSEMBLY CONTINUED
2
FRONT SUSPENSION ASSEMBLY
3
WHEEL ASSEMBLY
4
Kit 4278 - Page 3Kit 4278 - Page 6
STOCK
RAISED RIDE HEIGHT
USES PARTS WITH #37
CUSTOM SUSPENSION
SHOWN IN STEP #3
UPPER RADIATOR
HOSE LOCATES TO
HOLE IN RADIATOR
8
LOWER
RADIATOR HOSE
SEMI GLOSS BLACK
FRAME
TURNED
OVER
37
CUSTOM FRONT
SUSPENSION
SEMI GLOSS BLACK
38
STOCK FRONT
SUSPENSION
SEMI GLOSS BLACK
★77
OUTER
WHEEL
CHROME
78
WHEEL
RETAINER
★100
CUSTOM
WHEEL
CHROME
101
DISK
BRAKE
STEEL
29
LEFT EXHAUST
ALUMINUM
30
RIGHT EXHAUST
ALUMINUM
✱
✱
✱
✱
✱
✱
✱
33
CUSTOM AXLE
SPACERS
SEMI GLOSS BLACK
32
DIFFERENTIAL
SEMI GLOSS BLACK
31
REAR AXLE
SEMI GLOSS BLACK
METAL AXLE PIN
METAL AXLE PIN
TIRE
TIRE
CUSTOM
RAISED RIDE HEIGHT
POSITION
LOWERED RIDE
HEIGHT POSITION
OPTIONAL RIDE HEIGHT
STOCK RIDE HEIGHT
CUSTOM
STOCK
STOCK RIDE HEIGHT
POSITION
28
DRIVESHAFT
SEMI GLOSS BLACK
76
RIGHT STOCK
AXLE SPACER
SEMI GLOSS BLACK
75
LEFT STOCK
AXLE SPACER
SEMI GLOSS BLACK
METAL AXLE PINS
METAL AXLE PINS
DECAL
17
(18 REAR)
RADIATOR ASSEMBLY
2
ENGINE ASSEMBLY
1SUSPENSION ASSEMBLY CONTINUED
9
FRONT ASSEMBLY
10
Kit 4278 - Page 2 Kit 4278 - Page 7
RAISED RIDE HEIGHT
USE WITH #33 CUSTOM
AXLE SPACER
10
RIGHT
ENGINE BLOCK
CHEVY ENGINE RED
9
LEFT
ENGINE BLOCK
CHEVY ENGINE RED
ALUMINUM
12
ENGINE TOP
CHEVY ENGINE RED
STEEL
SEMI GLOSS
BLACK
13
ENGINE COVER
CHEVY ENGINE RED
DECAL
5 or 6
(STOCK)
DECAL
20
(CUSTOM)
DECAL
21
(CUSTOM)
DECAL
22
DECAL
5 or 6
(STOCK)
★47
ROCKER COVER
CHROME
(CHEVY ENGINE RED)
★47
ROCKER COVER
CHROME
(CHEVY ENGINE RED)
SEMI GLOSS
BLACK
11
OIL PAN
CHEVY ENGINE RED
GLOSS BLUE
15
EXHAUST
MANIFOLD
STEEL
15
EXHAUST
MANIFOLD
STEEL
80
STOCK AIR
CLEANER
SEMI GLOSS BLACK
17
FAN
SEMI GLOSS BLACK
DECAL
4
✱✱
✱
✱
✱
✱
COMPLETED
ENGINE
ASSEMBLY
41
FRAME
SEMI GLOSS BLACK
★49
ALTERNATOR
CHROME
14
FAN BELT
SEMI GLOSS
BLACK
PAINT PULLEYS
ALUMINUM
5
FAN SHROUD
TOP
SEMI GLOSS BLACK
6
FAN SHROUD
BOTTOM
SEMI GLOSS BLACK
7
RADIATOR
SEMI GLOSS BLACK
60
STOCK SHOCKS
SEMI GLOSS BLACK
34
SHORT SHOCKS
SEMI GLOSS BLACK
62
LONG SHOCKS
SEMI GLOSS BLACK
58
HEADLIGHTS
CLEAR
★44
GRILLE / BUMPER
CHROME
★45
HOOD TRIM
CHROME
★56
SIDE VIEW MIRROR
CHROME
★48
CUSTOM
AIR CLEANER
CHROME
WHITE
REAR ASSEMBLY
11
SILVER
(BODY COLOR)
★46
REAR BUMPER
CHROME
59
TAILLIGHTS
TRANSPARENT RED
LOWERED RIDE
HEIGHT
STOCK RIDE
HEIGHT
DECAL PLACEMENT
12
Semi Gloss Black
Flat Red
Gloss Blue Pearl
Chevy Engine Red
Gloss White
Aluminum
Silver
Steel
Turn Signal Amber
This paint guide is provided to complete this kit
as shown on the box.
Ce guide de peintures est fourni pour reproduire le modèle
réduit qui apparaît sur la boîte.
Noir satiné
Rouge mat
Bleu nacré brilliant
Rouge De Moteur De Chevy
Blanc brillant
Aluminum
Argent brillant metallisé
Acier
Ambre
* Study the assembly drawings.
* Each plastic part is identified by a number.
* In the assembly drawings, some parts will be
marked by a star (★) to indicate chrome
plated plastic.
* For better paint and decal adhesion, wash
the plastic parts in a mild detergent solution.
Rinse and let air dry.
* Check the fit of each piece before
cementing in place.
* Use only cement for polystyrene plastic.
* Scrape plating and paint from areas
to be cemented.
* Allow paint to dry thoroughly before
handling parts.
* Any unused parts may be discarded.
DECAL APPLICATION INSTRUCTIONS
1. Cut desired decal from sheet.
2. Dip decal in water for a few seconds.
3. Place wet decal on paper towel.
4. Wait until decal is movable on paper backing.
5. Place decal in position on model, face up and
slide backing away.
6. Press out air bubbles with a soft damp cloth.
7. Milkiness that may appear is for better decal
adhesion and will dry clear. Wipe away any
excess adhesive.
8. Do not touch decal until fully dry.
9. Allow the decals 48 hours to dry before
applying clear coat.
NOTE: Decals are compatible with
setting solutions or solvents.
READ THIS BEFORE YOU BEGIN LIRE CE QUI SUIT AVANT DE COMMENCER
* Etudier les schémas de montage.
* Chaque pièce en plastique est identifiée par un numéro.
* Sur les schémas de montage, certaines pièces sont
marquées d'une étoile (★) pour indiquer qu'elles sont en
plastique chromé.
* Pour une meilleure prise de la peinture et des autocollants,
laver les pièces en plastique avec une solution détergente peu
concentrée. Les rincer et les laisser sécher à l'air.
* Vérifier que chaque pièce s'ajuste bien avant
de la coller en place.
* N'utiliser que de la colle pour polystyrène.
* Gratter les parties à coller pour enlever le chrome et la peinture.
* Laisser la peinture bien sécher avant de manipuler les pièces.
* Toute pièce inutilisée peut être jetée.
DIRECTIVES D'APPLICATION DES AUTOCOLLANTS
1. Découper l'autocollant désiré de la feuille.
2. Tremper l'autocollant dans de l'eau pendant quelques secondes.
3. Placer l'autocollant mouillé sur une serviette en papier.
4. Attendez que l'autocollant puisse être déplacé sur son
support en papier.
5. Mettre l'autocollant en position sur le modèle face sur
le dessus et faire glisser le support pour l'enlever.
6. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air.
7. La substance laiteuse qui peut apparaître est destinée à
améliorer l'adhésion de l'autocollant et devient incolore au
séchage. Essuyer pour enlever tout excédent d'adhésif.
8. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec.
9. Laisser l'autocollant sécher pendant 48 heures avant
d'appliquer une couche transparente.
REMARQUE: Les autocollants sont compatibles avec
les solutions de fixage ou les solvants.
'63 CHEVY
® IMPALA™ SS
™ 2 'N 1
KIT 4278 85427800200
If you have any questions or comments, call our hotline at: (800) 833-3570
or, please write to:
Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007
Be sure to include the plan number (85427800200), part number, description, your return address and phone number.
Visit our website: www.revell.com
Revell Inc Elk Grove Village, IL. Copyright © 2010. All rights reserved.
Kit 4278 - Page 8
* REPEAT SEVERAL TIMES
* A REPETER PLUSIEURS FOIS
* CEMENT TOGETHER
* A COLLER
* REMOVE AND THROW AWAY
* A RETIRER ET JETER
* DO NOT CEMENT
* NE PAS COLLER
* DECAL
* DECAL COMANIE
* ASSEMBLY CAUTION
*ATTENTION D ASSEMBLEE
* OPTIONAL PARTS
* PIECES EN OPTION
* REPEAT PROCEDURE
* R E P E T E Z L E P R O C E D E
`` ` ` `
While locked in a battle for the
top spot in the annual sale races,
Chevrolet® gave it's popular Impala™
good-looking angular lines for '63 as
well as carrying over the "convert-
ible look" two door hardtop body
from 1962. Decades later, the 1963
Chevy® remains one of the most
desired subjects among both the
restoration and custom car crowd.
Your Revell model features an
opening hood and trunk plus mul-
tiple suspension positions, option-
al factory stock wheels and tires
or custom wheels with low profile
tires and decals with both facto-
ry stock and custom graphics.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Revell 63 CHEVY IMPALA SS 2 IN 1 Manuel utilisateur
- Taper
- Manuel utilisateur
dans d''autres langues
Documents connexes
-
Revell 85-7210 Mode d'emploi
-
-
-
-
-
-
-
-
-