THIRD REALITY 3RTHS24BZ Manuel utilisateur

3RTHS24BZ
Marque
THIRD REALITY
Modèle
3RTHS24BZ
Taper
Manuel utilisateur
Temperature & Humidity Sensor
User Manual
Index
1. Product Overview
2. Installation
3. Reset Button
4. Specifications
5. Setting up
6. Pairing with THIRDREALITY
7. Pairing with Amazon Echo
8. Pairing with SmartThings
9. Pairing with Hubitat
10. Pairing with Home Assistant
Product Overview
Front View Rear View
Installation
Reset Button
1 Press and hold the reset button on the left side of the sensor for 10 seconds and release the
hold.
2 Single press the reset button to switch the temperature display between Celsius and
Fahrenheit .
Specifications
Name Temperature and Humidity Sensor
Model 3RTHS24BZ
LED Screen 48.5mm x 41.0 mm
Dimensions 6.15cmx6.15cmx1.8cm
Net Weight 64g
Operating Voltage DC 3V
Battery Type AAA battery x 2 (included)
Wireless Connectivity ZigBee 3.0 2405~2480MHz
Setting up
Initializing Temp & Humidity Sensor
Power on: Remove the plastic stand on the back of the Temp & Humidity Sensor carefully, open
the battery cover on the back, remove the plastic insulation sheet and the sensor is powered
on,the blinking cloud icon on the the LED screen indicates the sensor is in pairing mode.
1Pairing mode: press and hold the reset button on the left side of the sensor for 5 seconds and
release the hold, the blinking cloud icon 切 图 on the LED screen indicates the sensor is in
pairing mode.
2Follow the on-screen instructions to set up your Temperature & Humidity Sensor.
Pairing with THIRDREALITY
Hub: Third Reality Smart Hub
App: Third Reality App
Pair the Temp & Humidity sensor with Third Reality Smart Hub.
Pairing
1Register and sign in your THIRDREALITY account, and add the THIRDREALITY hub.
2Remove the plastic stand on the back of the Temp & Humidity Sensor carefully, open the
battery cover on the back, remove the plastic insulation sheet and the sensor is powered on; Or
press and hold the reset button on the left side of the sensor for 5 seconds and release the hold;
The blinking cloud icon on the the LED screen indicates the sensor is in pairing mode.
3Tap “+” in the upper right in THIRDREALITY App, scroll down to choose the Temp & Humidity
Sensor Icon and follow the on-screen instructions to start the pairing process.
4The sensor will be discovered within one minute as “Temperature and Humidity Sensor 1” ,
the temperature and humidity data will be displayed in the device list .
⑤Tap the Temp & Humidity Sensor icon to enter the device page, you can see information like
the MAC address, battery level, software version and history records etc, you can also rename
the Temp & Humidity Sensor, and check for software updates.
Pairing with Amazon Echo
App: Amazon Alexa App
Devices: Echo devices with built-in ZigBee hubs such As Echo V4, Echo Plus V1 & V2, Echo Studio,
Echo Show 10, and Eero 6 & 6 pro.
①Ask Alexa to check for updates before pairing.
②Remove the plastic stand on the back of the Temp & Humidity Sensor carefully, open the
battery cover on the back, remove the plastic insulation sheet and the sensor is powered on; Or
press and hold the reset button on the left side of the sensor for 5 seconds and release the hold;
The blinking cloud icon on the the LED screen indicates the sensor is in pairing mode.
③Ask Alexa to discover devices, or open Alexa App, go to device page, tap “+” on top right,
choose “Add Device”, scroll down to the bottom and tap “other”, tap “DISCOVER DEVICES”, the
Temp & Humidity Sensor will be paired with your Echo device in a few seconds.
④Tap device icon to enter the device page, tap the setting icon to enter the settings page, you
can edit the name of the sensor; Or you can create routines with the sensor to control other
connected devices.
Pairing with SmartThings
App: SmartThings App
Devices: SmartThings Hub 2nd Gen(2015) & 3rd Gen.(2018), Aeotec Smart Home Hub.
①Before pairing, check for updates to make sure the SmartThings Hub firmware is up to date.
②Remove the plastic stand on the back of the Temp & Humidity Sensor carefully, open the
battery cover on the back, remove the plastic insulation sheet and the sensor is powered on; Or
press and hold the reset button on the left side of the sensor for 5 seconds and release the hold;
The blinking cloud icon on the the LED screen indicates the sensor is in pairing mode.
③Open the SmartThings App, tap “+” on the upper right corner to ”Add device” and then tap
“Scan” to “Scan for nearby devices”.
④The Smart Button will be paired with the SmartThings hub in a few seconds.
⑤Create routines to control connected devices.
Pairing with Hubitat
Website: http://find.hubitat.com/
Pairing Steps:
①Remove the plastic stand on the back of the Temp & Humidity Sensor carefully, open the
battery cover on the back, remove the plastic insulation sheet and the sensor is powered on; Or
press and hold the reset button on the left side of the sensor for 5 seconds and release the hold;
The blinking cloud icon on the the LED screen indicates the sensor is in pairing mode.
②Visit your Hubitat Elevation hub device page from your web browser, select the Devices menu
item from the sidebar, then select Discover Devices in the upper right.
③Click Start ZigBee Pairing button after you select a ZigBee device type, the Start
ZigBee Pairing button will put the hub in ZigBee pairing mode for 60 seconds.
④After pairing process is completed successfully, you can rename it if needed.
⑤Now you can see the Temp & Humidity Sensor on the Devices page.
Pairing with Home Assistant
Pairing steps：
①Remove the plastic stand on the back of the Temp & Humidity Sensor carefully,
open the battery cover on the back, remove the plastic insulation sheet and the
sensor is powered on, the blinking cloud icon on the the LED screen indicates the
sensor is in pairing mode.
②Make sure Home Assistant Integrations ZigBee Home Automation Setup is ready,
then go to “Configuration” page, click “integration”.
③Then click the “Devices” on the ZigBee item, the click “Add Devices”.
④After the pairing is completed successfully, it will show up in the page.
⑤Back to “Devices” page, then you can find the Temp & Humidity Sensor added.
⑥Click to enter in the control interface to set the Temp & Humidity Sensor.
⑦Click “+” belongs to Automation and then you can add different actions.
FAQ
Q1 How to factory reset the Temp & Humidity Sensor?
Press and hold the reset button on the left side of the sensor for 5 seconds and release the hold,
the blinking cloud icon on the the LED screen indicates the sensor is in pairing mode.
Q2 Why does the temperature fluctuate as I press the reset button?
The reset button is located near the ventilation hole, so the temperature reading rises as your
finger press the reset button, you need to wait for 20 seconds before the temperature reading
returns to normal.
Q3 The LED screen gets dirty, how to clean it?
You can clean the LED screen with alcohol wipes or damp soft cloth, prevent water from getting
into the monitor when cleaning it.
Limited Warranty
For limited warranty, please visit www.3reality.com/devicesupport
For customer support, please contact us at info@3reality.com or visit www.3reality.com
For help and troubleshooting related to Amazon Alexa, visit the Alexa app.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
FCC STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
your body
This equipment complies with RSS-102 radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm between
INDUSTEY CANADA STATEMENT:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation of the
device. In additional, this device complies with ICES-003 of the Industry Canada (IC) Rules.
Any Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Industry Canada licence-exempt RSS standard(s). These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
the radiator & your body.
INDUSTEY CANADA STATEMENT(French):
Cet appareil est conforme aux normes RSS exemptes de licence d'Industrie Canada. Son
fonctionnement est soumis aux deux conditions suivantes : (1) Cet appareil ne doit pas causer
d'interférences nuisibles et (2) cet appareil doit accepter toute interférence reçue, y compris les
interférences susceptibles de provoquer un fonctionnement indésirable de l'appareil. De plus, cet
appareil est conforme à la norme ICES-003 des règles d'Industrie Canada (IC). Tout changement ou
modification non expressément approuvé par la partie responsable de la conformité pourrait annuler
l'autorité de l'utilisateur à faire fonctionner l'équipement. Remarque : cet équipement a été testé et
déclaré conforme aux limites d'un appareil numérique de classe B, conformément aux normes RSS
exemptes de licence d'Industrie Canada. Ces limites sont conçues pour fournir une protection
raisonnable contre les interférences nuisibles dans une installation résidentielle. Cet équipement génère
des utilisations et peut émettre de l'énergie de radiofréquence et, s'il n'est pas installé et utilisé
conformément aux instructions, peut causer des interférences nuisibles aux communications radio.
Cependant, il n'y a aucune garantie que des interférences ne se produiront pas dans une installation
particulière. Si cet équipement cause des interférences nuisibles à la réception radio ou télévision, ce
qui peut être déterminé en éteignant et en rallumant l'équipement, l'utilisateur est encouragé à essayer
de corriger l'interférence par une ou plusieurs des mesures suivantes : -Réorientez ou déplacez
l'antenne de réception. -Augmenter la distance entre l'équipement et le récepteur. -Connectez
l'équipement à une prise sur un circuit différent de celui auquel le récepteur est connecté. -Consultez le
revendeur ou un technicien radio/TV expérimenté pour obtenir de l'aide. Cet équipement est conforme
aux limites d'exposition aux rayonnements RSS-102 établies pour un environnement non contrôlé. Cet
équipement doit être installé et utilisé avec une distance minimale de 2. Cet appareil est conforme aux
normes RSS exemptes de licence d'Industrie Canada. Son fonctionnement est soumis aux deux
conditions suivantes : (1) Cet appareil ne doit pas causer d'interférences nuisibles et (2) cet appareil
doit accepter toute interférence reçue, y compris les interférences susceptibles de provoquer un
fonctionnement indésirable de l'appareil. De plus, cet appareil est conforme à la norme ICES-003 des
règles d'Industrie Canada (IC).
Tout changement ou modification non expressément approuvé par la partie responsable de la
conformité pourrait annuler l'autorité de l'utilisateur à faire fonctionner l'équipement.
Remarque : cet équipement a été testé et déclaré conforme aux limites d'un appareil numérique de
classe B, conformément aux normes RSS exemptes de licence d'Industrie Canada. Ces limites sont
conçues pour fournir une protection raisonnable contre les interférences nuisibles dans une installation
résidentielle. Cet équipement génère des utilisations et peut émettre de l'énergie de radiofréquence et,
s'il n'est pas installé et utilisé conformément aux instructions, peut causer des interférences nuisibles
aux communications radio. Cependant, il n'y a aucune garantie que des interférences ne se produiront
pas dans une installation particulière. Si cet équipement cause des interférences nuisibles à la réception
radio ou télévision, ce qui peut être déterminé en éteignant et en rallumant l'équipement, l'utilisateur
est encouragé à essayer de corriger l'interférence par une ou plusieurs des mesures suivantes : -
Réorientez ou déplacez l'antenne de réception. -Augmenter la distance entre l'équipement et le
récepteur. -Connectez l'équipement à une prise sur un circuit différent de celui auquel le récepteur est
connecté. -Consultez le revendeur ou un technicien radio/TV expérimenté pour obtenir de l'aide.
Cet équipement est conforme aux limites d'exposition aux rayonnements RSS-102 établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de
20 cm entre le radiateur et votre corps.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13

THIRD REALITY 3RTHS24BZ Manuel utilisateur

3RTHS24BZ
Marque
THIRD REALITY
Modèle
3RTHS24BZ
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Autres documents