Samsung HW-Q950A Manuel utilisateur

FULL MANUAL

HW-Q950A

Imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register your product at

www.samsung.com/register

ENG - 2

SAFETY INFORMATION

SAFETY WARNINGS

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE

COVER (OR BACK).

NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

Refer to the table below for an explanation of symbols which may be

on your Samsung product.

CAUTION

RISK OF ELECTRIC SHOCK. DO NOT OPEN.

This symbol indicates that high voltage is present inside.

It is dangerous to make any kind of contact with any

internal part of this product.

This symbol indicates that this product has included

important literature concerning operation and

maintenance.

Class II product : This symbol indicates that a safety

connection to electrical earth (ground) is not required.

If this symbol is not present on a product with a power

cord, the product MUST have a reliable connection to

protective earth (ground).

AC voltage : Rated voltage marked with this symbol is AC

voltage.

DC voltage : Rated voltage marked with this symbol is DC

voltage.

Caution. Consult Instructions for use : This symbol

instructs the user to consult the user manual for further

safety related information.

WARNING

• To reduce the risk of re or electric shock, do not expose this

appliance to rain or moisture.

• To prevent injury, this apparatus must be securely attached to the

oor/wall in accordance with the installation instructions.

CAUTION

• Do not expose this apparatus to dripping or splashing. Do not put

objects lled with liquids, such as vases, on the apparatus.

• To turn this apparatus off completely, you must pull the power

plug out of the wall socket. Consequently, the power plug must be

easily and readily accessible at all times.

CAUTION (for Canada)

This device contains licence-exempt transmitter(s)/receiver(s) that

comply with Innovation, Science and Economic Development Canada’s

licence-exempt RSS(s). Operation is subject to the following two

conditions:

(1) This device may not cause interference.

(2) This device must accept any interference,

including interference that may cause undesired operation of the

device.

This device and its antenna(s) must not be co-located or operation in

conjunction with any other antenna or transmitter.

This device may automatically discontinue transmission if there is

no information to transmit, or an operational failure. Note that this

is not intended to prohibit the transmission of control or signaling

information or the use of repetitive codes where required by the

technology.

This Class B digital apparatus complies with Canadian ICES-003.

Radiation Exposure Statement

This equipment complies with IC RSS-102 radiation exposure limits

set forth for an uncontrolled environment. This equipment should be

installed and operated with minimum distance 20 cm between the

radiator & your body.

ENG - 3

Important Safety Instructions

Read these operating instructions carefully before using the unit.

Follow all the safety instructions listed below. Keep these operating

instructions handy for future reference.

1. Read these instructions.

2. Keep these Instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings.

Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including ampliers) that

produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-

type plug.

A polarized plug has two blades with one wider than the other.

A grounding type plug has two blades and a third grounding

prong. The wide blade or the third prong are provided for your

safety. If the provided plug does not t into your outlet, consult an

electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point where

they exit from the apparatus.

11. Only use attachments/accessories specied by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table

specied by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when

moving the cart/apparatus combination to avoid injury

from tip-over.

13. Unplug this apparatus during lightning storms or when unused for

long periods of time.

14. Refer all servicing to qualied service personnel. Servicing is

required when the apparatus has been damaged in any way, such

as power-supply cord or plug is damaged, liquid has been spilled

or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has

been dropped.

PRECAUTIONS

1. Ensure that the AC power supply in your house complies with the

power requirements listed on the identication sticker located

on the bottom of your product. Install your product horizontally,

on a suitable base (furniture), with enough space around it for

ventilation (3~4 inches). Make sure the ventilation slots are not

covered. Do not place the unit on ampliers or other equipment

which may become hot. This unit is designed for continuous use.

To fully turn off the unit, disconnect the AC plug from the wall

outlet. Unplug the unit if you intend to leave it unused for a long

period of time.

2. During thunderstorms, disconnect the AC plug from the wall

outlet. Voltage peaks due to lightning could damage the unit.

3. Do not expose the unit to direct sunlight or other heat sources.

This could lead to overheating and cause the unit to malfunction.

4. Protect the product from moisture (i.e. vases), and excess heat

(e.g. a replace) or equipment creating strong magnetic or electric

elds. Unplug the power cable from the AC wall socket if the unit

malfunctions. Your product is not intended for industrial use. It is

for personal use only. Condensation may occur if your product has

been stored in cold temperatures. If transporting the unit during

the winter, wait approximately 2 hours until the unit has reached

room temperature before using.

5. The battery used with this product contains chemicals that are

harmful to the environment. Do not dispose of the battery in the

general household trash. Do not expose the battery to excess

heat, direct sunlight, or re. Do not short circuit, disassemble, or

overheat the battery.

CAUTION : Danger of explosion if the battery is replaced

incorrectly. Replace only with the same or equivalent type.

Fabric cleaning

Remove any dirt or stain on the product surface immediately.

Removing and cleaning can be less effective for some substances or if

left for a prolonged time.

CAUTION

• Use a vacuum cleaner or an adhesive lint roller to remove dust,

handprints, and the likes.

‒ Some cleaning brushes may damage the product, depending on

the materials they contain.

‒ Towels and cleaning clothes may leave lint or dirt on the

product.

• Do not use a nail or other tools to scratch the dirt off. It may

damage the fabric.

• To remove oil or liquid stains, use a clean white cloth moist with

water. If the stain persists, wipe it with a mixture of water and

neutral detergent (such as dishwashing soaps) and a cloth.

‒ A non-neutral detergent or cleaner may cause discoloration or

fabric damage.

‒ After cleaning, use a dry cloth or hairdryer to dry the area.

‒ Do not use excessive force to avoid discoloration or fabric

damage.

ENG - 4

CONTENTS

01 Checking the Components 6

02 Product Overview 7

Top Panel of the Soundbar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Bottom Panel of the Soundbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

03 Using the Soundbar Remote Control 9

Inserting Batteries before using the Remote Control (AA batteries X 2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

How to Use the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Active Voice Amplier (AVA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Using the Hidden Buttons (Buttons with more than one function). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Output specications for the different sound effect modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Adjusting the Soundbar volume with a TV remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

04 Connecting the Soundbar 13

Connecting the power and units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

‒ Recommended Speaker Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

‒ Manually connecting the Subwoofer or Surround Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

‒ LED Indicator Lights on the Rear of Subwoofer and Surround Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

‒ Auto EQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

05 Using a wired connection to the tv 17

Method 1. Connecting with HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

‒ Connecting the TV that supports HDMI ARC (Audio Return Channel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Method 2. Connecting using an Optical Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

06 Using a wireless connection to the TV 19

Method 1. Connecting via Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Method 2. Connecting via Wi-Fi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

07 Connecting an External Device 21

Method 1. Connecting using an HDMI Cable (Capable of Dolby Atmos decoding and playback) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Method 2. Connecting using an Optical Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

08 Connecting a Mobile Device 23

Method 1. Connecting via Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Method 2. Connecting via Wi-Fi (Wireless Network). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Getting Started with Amazon Alexa (Built-in Alexa). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Getting Started with Alexa on Amazon Product (Works with Alexa). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Using the Tap Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

09 Connecting To Apple AirPlay 2 28

Connect and use with an Apple product. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

ENG - 5

10 Installing the Wall Mount 29

Installation Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Wallmount Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Installing the Surround Speakers on a Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

11 Installing the Soundbar above a TV Stand 30

Component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

12 Software Update 31

Auto Update. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

USB Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Initialization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

13 Troubleshooting 32

14 License 34

15 Open Source License Notice 34

16 Important Notes About Service 34

17 Specications and Guide 35

Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

ENG - 6

01 CHECKING THE COMPONENTS

VOL WOOFER

SOUNDBAR

SOUND

MODE

PAIR

Soundbar Main Unit Soundbar Remote Control / Batteries Subwoofer

POWER

x 2

x 4

Surround Speaker

(Left / Right)

Power Cord (Subwoofer, Surround Speaker,

Soundbar)

HDMI Cable

x 2

(M4 x L10)

Wall Mount Guide Holder-Screw Screw

x 2

x 4

Bracket-Wall Mount Rubber-Foot

• For more information about the power supply and power consumption, refer to the label attached to the product. (Label: Rear of the Soundbar

Main Unit)

• To purchase additional components or optional cables, contact a Samsung Service Center or Samsung Customer Care.

• For more information about the wallmount or rubber-foot, see pages 29~31.

• Design, specications, and App screen are subject to change without prior notice.

• The appearance of the accessories may differ slightly from the illustrations above.

ENG - 7

02 PRODUCT OVERVIEW

Top Panel of the Soundbar

1 2 3

4

Position the

product so that the

SAMSUNG logo is

located on the top.

1

(Multi Function) Button

• In standby mode, press the (Multi Function) button to turn on the Soundbar.

• Press the (Multi Function) button to change the input source.

2 Display

Displays the product’s status and current mode.

D.IN → HDMI 1 → HDMI 2 → Wi-Fi → BT

3

(Mic On/Off) Button

Press the button to turn the microphone on or off.

4

(Volume) Button

Adjusts the volume.

• When you plug in the AC cord, the power button will begin working in 4 to 6 seconds.

• When you turn on this unit, there will be a 4 to 5 second delay before it produces sound.

• If you hear sounds from both the TV and Soundbar, go to the Settings menu for the TV audio and change the TV speaker to External Speaker.

Bottom Panel of the Soundbar

ID SET

HDMI IN 1

HDMI IN 2

POWER

NETWORK

SERVICE

DIGITAL AUDIO IN

(OPTICAL)

HDMI TO TV

(eARC/ARC)

HDMI 2

HDMI 1

ID SET

(WOOFER/REAR)

POWER

ID SET

NETWORK

SERVICE

ID SET

(WOOFER/REAR)

DIGITAL AUDIO IN

(OPTICAL)

HDMI TO TV

(eARC/ARC)

HDMI 2

HDMI 1

ID SET

HDMI IN 1

HDMI IN 2

POWER

NETWORK

SERVICE

DIGITAL AUDIO IN

(OPTICAL)

HDMI TO TV

(eARC/ARC)

HDMI 2

HDMI 1

ID SET

(WOOFER/REAR)

POWER

ID SET

NETWORK

SERVICE

ID SET

(WOOFER/REAR)

DIGITAL AUDIO IN

(OPTICAL)

HDMI TO TV

(eARC/ARC)

HDMI 2

HDMI 1

ID SET

HDMI IN 1

HDMI IN 2

POWER

NETWORK

SERVICE

DIGITAL AUDIO IN

(OPTICAL)

HDMI TO TV

(eARC/ARC)

HDMI 2

HDMI 1

ID SET

(WOOFER/REAR)

POWER

ID SET

NETWORK

SERVICE

ID SET

(WOOFER/REAR)

DIGITAL AUDIO IN

(OPTICAL)

HDMI TO TV

(eARC/ARC)

HDMI 2

HDMI 1

ID SET

HDMI IN 1

HDMI IN 2

POWER

NETWORK

SERVICE

DIGITAL AUDIO IN

(OPTICAL)

HDMI TO TV

(eARC/ARC)

HDMI 2

HDMI 1

ID SET

(WOOFER/REAR)

POWER

ID SET

NETWORK

SERVICE

ID SET

(WOOFER/REAR)

DIGITAL AUDIO IN

(OPTICAL)

HDMI TO TV

(eARC/ARC)

HDMI 2

HDMI 1

1

2

3

4

5

7

6

1 POWER

Connect the Soundbar’s AC power cable. (See page 13)

2 ID SET (WOOFER/REAR)

Press to connect the Soundbar to surround speakers and a subwoofer wirelessly.

3 NETWORK

Press to connect to a wireless network (Wi-Fi) via the SmartThings app.

4 SERVICE

Connect a USB storage device to upgrade the product’s software.

5 DIGITAL AUDIO IN (OPTICAL)

Connect to the digital (optical) output of an external device. (See page 22)

6 HDMI 1 / HDMI 2

Inputs digital video and audio signals simultaneously using an HDMI cable.

Connect to the HDMI output of an external device. (See page 21)

ENG - 8

7 HDMI TO TV (eARC/ARC)

Connect to the HDMI jack on a TV. (See page 17)

• When disconnecting the power cord from a wall outlet, pull the plug. Do not pull the cable.

• Do not connect this unit or other components to an AC outlet until all connections between components are complete.

ENG - 9

03 USING THE SOUNDBAR REMOTE CONTROL

Inserting Batteries before using the Remote Control (AA batteries X 2)

Slide the back cover in the direction of the arrow until it is completely removed. Insert 2 AA batteries

(1.5V) oriented so that their polarity is correct. Slide the battery cover back into position.

How to Use the Remote Control

1

2

3

4

5

6

7

8

9

10

1

Power

Turns the Soundbar on and off.

• Auto Power Down Function

The unit turns off automatically in the following situations:

• In D.IN / HDMI 1 / HDMI 2 / Wi-Fi / BT mode if there is no audio

signal for 18 minutes.

2

Source

Press to select a source connected to the Soundbar.

• Voice Feedback On/Off

You can turn on or off the Voice Feedback.

Press and hold the

(Source) button on the remote control for

5 seconds while the Soundbar is off (Standby mode).

Each time you change the Voice Feedback setting, the OLED Display

will show “AUI OFF” (Default) or “AUI ON”.

3

Mute

Press the

(Mute) button to mute the sound.

Press it again to unmute the sound.

4

SOUND MODE

You can select the desired sound mode by choosing STANDARD,

SURROUND, GAME PRO, or ADAPTIVE SOUND.

• STANDARD

Outputs the original sound.

• SURROUND

Provides a wider sound eld than standard.

• GAME PRO

Provides stereoscopic sound to immerse you in the action while

gaming.

• ADAPTIVE SOUND

Analyzes the content in real time and automatically provides the

optimal sound eld based on the characteristics of the content.

5

Bluetooth PAIR

Switch the Soundbar to Bluetooth pairing mode. Press the button and

wait for the “BT PAIRING” screen to connect to a new Bluetooth device.

6

Play / Pause

You can also play or pause music by pressing the button.

ENG - 10

7

Up/Down/Left/

Right

Press the indicated areas to select Up/Down/Left/Right.

Press Up/Down/Left/Right on the button to select or set functions.

• Music Skip

Press the Right button to select the next music le. Press the Left button to select the previous music le.

• ID SET

Use this option when the Subwoofer or Surround Speakers are not connected or need reconnection.

While powered off, press and hold the Up button for 5 seconds to perform ID SET. (See page 14.)

8

Sound Control

When pressed, the setting items such as AUTO EQ, AVA, TREBLE, BASS, SYNC, CENTER LEVEL, SIDE LEVEL, FRONT

TOP LEVEL, REAR LEVEL, REAR TOP LEVEL, REAR SIDE LEVEL , and VIRTUAL ON/OFF are displayed in sequence.

The desired item can be adjusted using the Up/Down buttons.

• To control the volume of the treble or bass sound, select TREBLE or BASS in Sound Settings, and then adjust

the volume between -6~+6 by using the Up/Down buttons.

• Press and hold the

(Sound Control) button for about 5 seconds to adjust the sound for each frequency band.

150Hz, 300Hz, 600Hz, 1.2kHz, 2.5kHz, 5kHz, and 10kHz are selectable using the Left/Right buttons and each

can be adjusted to a setting between -6 to +6 using the Up/Down buttons.

(Make sure the Sound mode is set to “STANDARD”.)

• To control the volume of the each speaker select CENTER LEVEL, SIDE LEVEL, or FRONT TOP LEVEL in Sound

Settings, and then adjust the volume between -6~+6 by using the Up/Down buttons.

• If the video on the TV and audio from the Soundbar are not synchronized, select SYNC in Sound Control, and

then set the audio delay between 0~300 milliseconds by using the Up/Down buttons.

• SYNC is only supported for some functions.

• If Surround Speakers are connected, select REAR LEVEL, REAR TOP LEVEL, or REAR SIDE LEVEL and then use

the Up/Down buttons to adjust the volume within a -6 to +6 range.

• The VIRTUAL Speaker function can be turned ON/OFF by using the Up/Down buttons.

• You can use the AUTO EQ function if a subwoofer is connected.

9

WOOFER LEVEL

Push the button up or down to adjust the level of the woofer to -12 or between -6 to +6. To set the woofer volume

level to 0 (Default), press the button.

10

VOLUME

Push the button up or down to adjust the volume.

• Mute

Press the VOL button to mute the sound. Press it again to unmute the sound.

Active Voice Amplier (AVA)

• Analyses external noise in real time while soundbar is playing, so that voice audio can always be heard clearly.

• No data is saved during the analysis.

Using the Hidden Buttons (Buttons with more than one function)

Hidden Button

Reference page

Remote Control Button Function

WOOFER (Up) TV remote control On/Off (Standby) page 12

Up ID SET page 14

(Sound Control)

7 Band EQ page 10

ENG - 11

Output specications for the different sound effect modes

Effect Input

Output

With Subwoofer & Surround Speaker

STANDARD

2.0 ch 2.1 ch

5.1 ch 5.1 ch / 7.1 ch (DTS)

7.1 ch 7.1 ch

Dolby Atmos®, DTS:X 7.1.4 ch

SURROUND

2.0 ch 11.1.4 ch

5.1 ch 11.1.4 ch

7.1 ch 11.1.4 ch

Dolby Atmos®, DTS:X 11.1.4 ch

GAME PRO

2.0 ch 11.1.4 ch

5.1 ch 11.1.4 ch

7.1 ch 11.1.4 ch

Dolby Atmos®, DTS:X 11.1.4 ch

ADAPTIVE SOUND

2.0 ch 11.1.4 ch

5.1 ch 11.1.4 ch

7.1 ch 11.1.4 ch

Dolby Atmos®, DTS:X 11.1.4 ch

The Surround Speakers will not produce sounds for 2 channel output while STANDARD mode is in use. To enable sound for the Surround

Speakers, change the effect mode to SURROUND.

ENG - 12

Adjusting the Soundbar volume with a TV remote control

Adjust the Soundbar volume using the TV’s remote control.

• This function can be used with IR remote controls only. Bluetooth remote controls (remote controls that require pairing) are not

supported.

• Set the TV speaker to External Speaker to use this function.

• Manufacturers supporting this function:

VIZIO, LG, Sony, Sharp, PHILIPS, PANASONIC, TOSHIBA, Hisense, RCA

1. Turn Off the Soundbar.

2. Push up and hold the WOOFER button for 5 seconds.

Each time you push the WOOFER button up and hold it for 5 seconds, the mode switches in the following order: “OFF-TV REMOTE” (Default

mode), “SAMSUNG-TV REMOTE”, “ALL-TV REMOTE”.

Remote Control Button Display Status

SOUND

MODE

VOL

WOOFER

SOUNDBAR

(Default mode)

OFF-TV REMOTE

Disable the TV remote control.

SOUND

MODE

VOL

WOOFER

SOUNDBAR

SAMSUNG-TV REMOTE

Enable a Samsung TV’s IR remote control.

SOUND

MODE

VOL

WOOFER

SOUNDBAR

ALL-TV REMOTE

Enable a third-party TV’s IR remote control.

ENG - 13

04 CONNECTING THE SOUNDBAR

Connecting the power and units

Use the Power cord to connect the Subwoofer, Surround Speakers, and Soundbar to an electrical outlet in the following order:

• For more information about the required electrical power and power consumption, refer to the label attached to the product. (Label: Rear of

the Soundbar Main Unit)

1. Connect the Power cord to the Subwoofer.

POWER

Rear of Subwoofer

Power Cord

2. Connect the power cord to the Left and Right Surround Speakers.

POWER

Bottoms of the Left and

Right Surround Speakers

Power Cord

3. Connect the Power cord to the Soundbar.

HDMI IN 1

HDMI IN 2

ID SET

(WOOFER,

REAR)

POWER

NETWORK

SERVICE

DIGITAL AUDIO IN

(OPTICAL)

HDMI TO TV

(eARC/ARC)

HDMI 1

HDMI 2

ID SET

POWER

Bottom of the Soundbar

Main Unit

Power Cord

4. Connect power to the Soundbar, Subwoofer and Surround Speakers. The Subwoofer and Surround Speakers are automatically connected when

the Soundbar is turned on.

LINK LED - Blue is On

NOTE

• Connect the Subwoofer and Surround Speakers power before connecting to the Soundbar. The Subwoofer and Surround Speakers will be

automatically connected when turning on the Soundbar.

• If you unplug and reconnect the power cord when the product is turned on, the Soundbar turns on automatically.

ENG - 14

Recommended Speaker Layout

150° 150°

135° 135°

0°

Subwoofer

Soundbar

Surround Speaker L Surround Speaker R

CAUTION

• Wireless receiving antennas are built into the wireless subwoofer and

surround speakers. Keep the units away from water and moisture.

• For optimal listening performance, make sure that the areas around the

wireless subwoofer and surround speakers locations are clear of any

obstructions.

Manually connecting the Subwoofer or Surround Speakers

Before performing the manual connection procedure below:

• Check whether the power cables for the Soundbar and subwoofer or Surround Speakers are connected properly.

• Make sure that the Soundbar is turned off.

1. Turn off the Soundbar main.

2. Press and hold ID SET on the rear of the subwoofer and surround speakers for at least 5 seconds.

• The red indicator at the rear of each speaker turns off and the blue indicator blinks.

5 Sec

Blinking

blue fast

Rear of Subwoofer Rear of Subwoofer

Blinking blue fast

POWER

x 2

Rear of the Left and Right Surround Speakers

5 Sec

3. Press the Up button on the remote control for 5 seconds.

• The ID SET message appears on the display of the Soundbar for a moment, and then it disappears.

• The Soundbar will automatically power on when ID SET is complete.

SOUND

MODE

PAIR

5 Sec

ID SET

ENG - 15

4. Check if the LINK LED is solid blue (connection complete).

LINK LED - Blue is On

The LINK LED indicator stops blinking and glows a solid blue when a connection

is established between the Soundbar and the Wireless Subwoofer, surround

speakers.

LED Indicator Lights on the Rear of Subwoofer and Surround Speakers

LED Status Description Resolution

Blue

On

Successfully connected

(normal operation)

-

Blinking Recovering the connection

Check if the power cable attached to the main Soundbar

unit is connected properly or wait about 5 minutes.

If blinking persists, try manually connecting the

subwoofer and Surround Speakers. See page 14.

Red

On

Standby (with the

Soundbar main unit turned

off)

Check if the power cable attached to the main Soundbar

unit is connected properly.

Connection failed

Connect again. See the instructions for manual

connection on page 14.

Red and blue

Blinking Malfunction

See the contact information for the Samsung Service

Center in this manual.

NOTE

• If the main unit is powered off, the wireless subwoofer will go into stand-by mode and the STANDBY LED on the rear of the sub-woofer will

turn red after blinking in blue several times.

• If you use a device that uses the same frequency as the Soundbar near the Soundbar, interference may cause some sound interruption.

• The maximum transmission distance of the main unit’s wireless signal is about 32.8 ft (10 m), but may vary depending on your operating

environment. If a steel-concrete or metallic wall is between the main unit and the wireless subwoofer, the system may not operate at all

because the wireless signal cannot penetrate metal.

CAUTION

• Wireless receiving antennas are built into the wireless subwoofer and Surround Speakers. Keep the unit away from water and moisture.

• For optimal listening performance, make sure that the area around the wireless subwoofer and the Surround Speakers are clear of any

obstructions.

ENG - 16

Auto EQ

Samsung’s Auto EQ Technology uses a microphone mounted in the subwoofer to detect and correct low-frequency response peaks caused by the

room dimensions and the subwoofer location. The result will be a more neutral overall low-frequency response.

• Subwoofer should be placed with a minimum of 3” (8 cm) clearance from each side to the nearest boundary.

• You must keep the room as quiet as possible while operating the Auto EQ tuning.

• Do not use any buttons until the Auto EQ tuning is complete.

• Auto EQ tuning takes about 2 minutes.

• During Auto EQ tuning, there is no sound from the Soundbar’s main unit and rear speakers.

If you are using the function for the rst time

1. Press the (Sound Control) button until Auto EQ is selected.

2. Press the Up/Down buttons to select Tuning, and then press the button.

3. Tuning will start, and the progress appears in percentage.

‒ To cancel tuning, press the Up, Down, Left, Right or button, and then press the button to conrm.

‒ If the tuning is failed, LED blinks in red.

‒ If the tuning is successful, LED blinks in blue.

If you have done the tuning process

1. Press the (Sound Control) button until Auto EQ is selected.

2. Press the Up/Down buttons to select Tuning, and then press the button.

3. Press the Up/Down buttons to select one of the following options.

‒ On: Turn on the previously tuned EQ settings.

‒ Off: Turn on the default EQ settings.

‒ Tuning: Start the tuning process again.

ENG - 17

05 USING A WIRED CONNECTION TO THE TV

Method 1. Connecting with HDMI

CAUTION

• When both the HDMI cable and optical cable are connected, the HDMI signal is received rst.

• To connect the HDMI cable between the TV and Soundbar, be sure to connect the terminals marked ARC. Otherwise, the TV sound may not

be output.

• The recommended cable is High Speed HDMI Cable with Ethernet.

Connecting the TV that supports HDMI ARC (Audio Return Channel)

HDMI IN

(ARC)

HDMI TO TV

(eARC/ARC)

Connect to the HDMI IN

(ARC) port of your TV.

Connect to the HDMI TO

TV (eARC/ARC) port of the

Soundbar main unit.

HDMI Cable

Top of the Soundbar

Bottom of the Soundbar

TV ARC

1. With the Soundbar and TV turned off, connect the HDMI cable as shown in the gure.

2. Turn on the Soundbar and TV.

3. “TV ARC” appears in the display window of the Soundbar main unit and the Soundbar plays TV sound.

• When the TV sound is not output, press the (Multi Function) button at the top of the Soundbar or the (Source) button on the remote

control to select the “D.IN” mode. The screen displays “D.IN” and “TV ARC” in sequence, and TV sound is played.

• When connecting a TV that supports the eARC function, “eARC” appears on the display and the sound is heard.

• To connect with eARC, the eARC function in the TV menu should be set to On. Refer to the TV user manual for details on setting. (e.g.

Samsung TV : Home ( ) → Settings ( ) → Sound → Expert Settings → HDMI-eARC Mode (Auto))

• If “TV ARC” does not appear in the display window of the Soundbar main unit, conrm that the HDMI cable is connected to the correct port.

• Use the volume buttons on the TV’s remote control to change the volume on the Soundbar.

NOTE

• When you connect the TV that supports the HDMI ARC (Audio Return Channel) to the Soundbar with an HDMI cable, you can transmit the

digital video and audio data without connecting a separate optical cable.

• We recommend you use a coreless HDMI cable if possible. If you use a cored HDMI cable, use one whose diameter is less than 0.55 inches (14

mm).

• This function is not available if the HDMI cable does not support ARC.

• When the audio in a broadcast is encoded in Dolby Digital and the “Digital Output Audio Format” on your TV is set to PCM, we recommend that

you change the setting to Dolby Digital. When the setting on the TV is changed, you will experience better sound quality. (The TV menu may

use different words for Dolby Digital and PCM depending on the TV manufacturer.)

ENG - 18

Method 2. Connecting using an Optical Cable

Pre-connection Checklist

• When both the HDMI cable and optical cable are connected, the HDMI signal is received rst.

• When you use an optical cable and the terminals have covers, be sure to remove the covers.

OPTICAL OUT

DIGITAL AUDIO IN

(OPTICAL)

HDMI 1

HDMI 2

Optical Cable (not supplied)

Bottom of the Soundbar

Top of the Soundbar

D.IN

1. With the TV and Soundbar turned off, connect the DIGITAL AUDIO IN (OPTICAL) port on the Soundbar and the OPTICAL output port on the TV

with the optical cable (not supplied), as shown in the gure.

2. Turn on the Soundbar and TV.

3. Press the (Multi Function) button at the top of the Soundbar or the (Source) button on the remote control to select the “D.IN” mode.

4. The TV sound is output from the Soundbar.

Using the Q-Symphony Function

For Q-Symphony, the Soundbar syncs with a Samsung TV to output sound through two devices for optimum surround effect. When the Soundbar

is connected, the menu, “TV+Soundbar” appears under the Sound Output menu of the TV. Select the corresponding menu.

TV menu

HDMI Cable

OR

Optical Cable (not supplied)

D.IN

• TV menu example: TV + [AV] Soundbar series name (HDMI)

NOTE

• It can operate according to the Codec supported by TV.

• This function is supported only when the HDMI Cable or Optical Cable (not supplied) is connected.

• This function is available in some Samsung TVs and some Soundbar models.

• When using Q-Symphony, you can only choose GAME PRO or ADAPTIVE SOUND.

Using the Spacet sound

Provides optimized sound quality by analyzing the listening spaces.

To enable this function, turn on the Adaptive Sound+ mode on your Samsung TV menu.

(Home ( ) → Settings ( ) → General → Intelligent Mode Settings → Adaptive Sound+)

NOTE

• The sound mode on your Soundbar will automatically change to Adaptive Sound+ if you enable the Adaptive Sound+ mode on your TV.

• This function works when the Soundbar connects to some of the Samsung TVs.

ENG - 19

06 USING A WIRELESS CONNECTION TO THE TV

Method 1. Connecting via Bluetooth

When a Samsung TV is connected using Bluetooth, you can hear stereo sound without the hassle of cabling.

• Only one Samsung TV can be connected at a time.

• Samsung TV that supports Bluetooth can be connected. Check the specications of your TV.

SOUND

MODE

PAIR

5 Sec

Top of the Soundbar

BT PAIRING

OR

The initial connection

1. Press the PAIR button on the Soundbar remote control to enter the “BT PAIRING” mode.

(OR)

a. Press the

(Multi Function) button on the top panel and then select “BT”.

“BT” changes to “BT PAIRING” in a few seconds automatically or changes to “BT READY” if there is a connect record.

b. When “BT READY” appears, press and hold the (Mic On/Off) button on the top panel of the Soundbar for more than 5 seconds to

display “BT PAIRING”.

2. Select Bluetooth mode on the Samsung TV.

(e.g. Home (

) → Settings ( ) → Sound → Sound Output → Bluetooth Speaker List → [AV] Samsung Soundbar Q950A (Bluetooth))

3. Select “[AV] Samsung Soundbar Q950A” from the list on TV’s screen.

An available Soundbar is indicated with “Need Pairing” or “Paired” on the TV’s Bluetooth device list. To connect the Samsung TV to the

Soundbar, select the message, and then establish a connection.

• When the Samsung TV is connected, [TV Name] → “BT” appears on the Soundbar’s top display.

4. You can now hear Samsung TV sound from the Soundbar.

• After you have connected the Soundbar to your Samsung TV the rst time, use the “BT READY” mode to reconnect.

If the device fails to connect

• If you have an existing Soundbar (e.g., [AV] Samsung Soundbar Q950A) on the list of speakers on the Samsung TV, delete it.

• Then repeat steps 1 through 3.

Disconnecting the Soundbar from the Samsung TV

Press the (Multi Function) button at the top of the Soundbar or the (Source) button on the remote control to select the mode other than

“BT”.

• Disconnecting takes time because the Samsung TV must receive a response from the Soundbar.

(The time required may differ, depending on the Samsung TV model.)

What is the difference between BT READY and BT PAIRING?

• BT READY : In this mode, you can reconnect any Samsung TV or mobile device that was connected before.

• BT PAIRING : In this mode, you can connect a new device to the Soundbar.

(Press the PAIR button on the Soundbar remote control or press and hold the (Mic On/Off) button on the top of the Soundbar for more

than 5 seconds while the Soundbar is in “BT” mode.)

Notes on Bluetooth connection

• Locate a new device within 3.28 ft (1 m) to connect via Bluetooth communication.

• If asked for a PIN code when connecting a Bluetooth device, enter <0000>.

• The Soundbar automatically turns off after 18 minutes in the Ready state.

• The Soundbar may not perform Bluetooth search or connection correctly under the following circumstances:

‒ If there is a strong electrical eld around the Soundbar.

‒ If several Bluetooth devices are simultaneously paired with the Soundbar.

‒ If the Bluetooth device is turned off, not in place, or malfunctions.

• Electronic devices may cause radio interference. Devices that generate electromagnetic waves must be kept away from the Soundbar main

unit - e.g., microwaves, wireless LAN devices, etc.

ENG - 20

Method 2. Connecting via Wi-Fi

Pre-connection Checklist

• Wi-Fi connection is available only on Samsung TV.

• Check whether the wireless router (Wi-Fi) is turned on and the TV is connected to the router.

• The TV and Soundbar must be connected to the same wireless network (Wi-Fi).

• If your wireless router (Wi-Fi) uses a DFS channel, you will not be able to establish a Wi-Fi connection between the TV and Soundbar.

Contact your Internet service provider for details.

• Because the menus may differ depending on the year of manufacture, refer to your TV manual.

• To connect the TV to the Soundbar via Wi-Fi, connect the Soundbar to the wireless router rst. See page 24, for details on how to

establish a Wi-Fi connection.

1. For more information about Wi-Fi connection to the Soundbar, see page 24, “Method 2. Connecting via Wi-Fi (Wireless Network)”.

2. Change the input source of the TV by using the Audio menu to Soundbar.

• Samsung TVs released in 2017 or later

Home (

) → Settings ( ) → Sound → Sound Output → [AV] Samsung Soundbar Q950A (Wi-Fi)

La page charge ...

Samsung HW-Q950A Manuel utilisateur

Samsung HW-Q950A Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents