Pivo Remote Control 2.0 Manuel utilisateur

Taper
Manuel utilisateur
Pivo Remote Control 2.0 Manual
For FC, IC, RED, MIC JAPAN Certs.
Manufacturer Name : 3i Inc
Factory Name : Nteklogic
2022.01.24
Contents
1. Introduction of the product
2. Product Descriptions
3. LED status / How to use
1. Introduction of the product
Pivo Remote Control is to connect and control Pivo Pod X and Pivo Pod Max via
bluetooth. Cannot be used with Pivo Pod Red, Silver, Black, and Lite(RF
connection)By using the remote control, the user can use every function of Pivo
from a distance. There are 9 physical buttons and an LED indicator. Powered by
2 AAA batteries. There are up, down, right, left, OK, +, -, pause, and track
buttons. Red, Green, and Blue LEDs will interact with the connection status.
Product image : Pivo Remote Control
2. Product description
Purpose : To control Pivo Pod from distance
1. Specification
1.1. General specification
ITEM
Specification
Product Name
PIVO REMOTE CONTROL 2.0
Model
PV-RC2
Standard
Bluetooth Low Energy (Bluetooth 5.2)
Battery
1.5V LR03 (AAA Size) Battery x2
LED
3 color RGB for status indicators
Connect, Operation state
Dimension
100(W) x 38(D) x 18(H)
Weight
25 g (without Battery)
Transmitter Supply Voltage
3V
Receiver Supply Voltage
3V
1.1. Power supply
Two AAA batteries are directly connected
1.2. LED
PIVO REMOTE CONTROL has RGB LEDs to indicate various statuses.
- Green : Input when connected
- Blue : Bluetooth pairing status / Connected
- Red : Input when disconnected
1.3. Button
Pivo Remote Control 2.0 has 9 buttons for various actions.
3. LED Status / How to use
1) LED status
a. Pressing the button when connected
- Green LED blink(Blue LED off when pressed)
- Blue LED ON(Green LED off when not pressed)
b. Pressing the button when disconnected
- Red LED blink
c. OTA F/W update status
- Green LED blink until finish
- Green LED on 1.5 secs and turn off when completed
- Red LED blink 3 times if the update failed
2) How to connect
a. Connecting to the Pivo Pod X / Max
a. Press OK button less than 0.5 secs of the remote to go into the pairing mode
b. Blue LED blink on until it is paired
c. Blue LED on when pairing is successful
b. Pairing Unsuccessful
a. Press OK button less than 0.5sec of the remote to go into the pairing mode
b. Blue LED blink on until it is paired for 10 secs
c. LED OFF
3) When using with Pivo Pod X
Not connected to App
Connected to App
Pivo Present App
Up
Single press
Tilt up
Zoom-in
Zoom-in
Down
Single press
Tilt Down
Zoom-out
Zoom-out
Right
Single press
Counter-clockwise
rotation
Next slide
Double press
Continuous counter-
clockwise rotation
Left
Single press
Clockwise rotation
Previous slide
Double press
Continuous clockwise
rotation
OK
Single press
400 degree clockwise
Capture / start-
stop vide
Switch Modes
+
Single press
Speed up
Counter-clockwise
rotation
Double press
Maximum speed
-
Single press
Speed down
Clockwise rotation
Double press
Minimum speed
Pause
Single press
Stop rotation
Select Target
Pause/Resume
recording
Track
Single press
Go to default position
Reset Tracking
Tracking ON/OFF
4) When using with Pivo Pod Max
Not connected to App
Connected to App
Pivo Present App
Up
Single press
Zoom-in
Zoom-in
Down
Single press
Zoom-out
Zoom-out
Right
Single press
Counter-clockwise
rotation
Next slide
Double press
Continuous counter-
clockwise rotation
Left
Single press
Clockwise rotation
Previous slide
Double press
Continuous clockwise
rotation
OK
Single press
400 degree clockwise
Capture / start-
stop vide
Switch Modes
+
Single press
Speed up
Counter-clockwise
rotation
Double press
Maximum speed
-
Single press
Speed down
Clockwise rotation
Double press
Minimum speed
Pause
Single press
Stop rotation
Select Target
Pause/Resume
recording
Track
Single press
Reset Tracking
Tracking ON/OFF
FCC Information to User
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
con-nected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution
Modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
FCC Compliance Information : This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause
undesired operation.
CAUTION : Exposure to Radio Frequency Radiation.
Antenna shall be mounted in such a manner to minimize the potential for human contact during
normal operation. The antenna should not be contacted during operation to avoid the possibility
of exceeding the FCC radio frequency exposure limit.
French Example Canadian Compliance Statements
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil
nedoit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnant en conjonction
avec une autre antenne ou transmetteur.
Declaration of conformity
We, 3i Inc of
101-117, 29, Dongbu-ro, Dong-gu, Daegu, Republic of Korea
declare under our sole responsibility that our product
Manufacturer: Nteklogic
Address: 42, Maehwa-ro, Bundang-gu, Seongnam-si, Gyeonggi-do, Republic of Korea
Contact Person: Hyekang, Park
E-mail: cert@3i.ai
OPERATING FREQUENCY: 2 402 MHz ~ 2 480 MHz
OUTPUT POWER: 0.23 dBm
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Pivo Remote Control 2.0 Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues