CREE LIGHTING CPY250 Richmond Civic Upgrade Kit Guide d'installation

Marque: CREE LIGHTING

Modèle: CPY250 Richmond Civic Upgrade Kit

Taper: Guide d'installation

INSTALLATION INSTRUCTIONS

1 of 2 CI391X05R1_A

CPY Series

Richmond Series Upgrade Kit

Includes: CPY250 Luminaries

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed including the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

1. DANGER – RISK OF SHOCK – DISCONNECT POWER BEFORE INSTALLATION

DANGER – RISQUE DE CHOC – COUPER L’ALIMENTATION AVANT L’INSTALLATION

2. This LED upgrade product is UL Classied for use with Richmond and Whiteway Civic only. DO NOT install into any other

manufacturer’s luminaire. To maintain existing Luminaires’ UL listing, the LED Upgrade Kit must be UL Classied for use with the

manufacturer and model of existing luminaire. Consult CREE Customer support to see if other luminaires are classied to be used with

this LED Upgrade Kit.

Ce produit upgrade LED est classié UL pour une utilisation avec la série Richmand et Whiteway Civic seulement. Ne pas installez ce upgrade

LED dans le luminaire de tout autre fabricant. Pour maintenir la qualication UL des Luminaires existants, le kit LED upgrade doit être classié

UL pour une utilisation avec le fabricant et le modèle de luminaire existant. Consulter CREE Support Clientèle pour voir si les autres luminaires

peuvent être utilisés avec ce upgrade LED.

3. WARNING – Risk of re or electric shock. LED Upgrade Kit installation requires knowledge of luminaires electrical systems. If not

qualied, do not attempt installation. Product must be installed in accordance with NEC or your local electrical code. If you are not

familiar with these codes and requirements, contact a qualied electrician.

ATTENTION- Risque d’incendie ou de choc électrique. L’installation du kit upgrade LED exige la connaissance des systèmes électriques pour

luminaires. Si non qualié, ne tentez pas d’installation. Ce produit doit être installé conformément à NEC ou votre code électrique local. Si vous

n’êtes pas familier avec ces codes et ces exigences, veuillez contacter un électricien qualié.

4. WARNING – Risk of re or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for installation of the LED

Upgrade Kit. Check for enclosed wiring and components.

ATTENTION - Risque d’incendie ou de choc électrique. Câblage électriques peuvent être endommagés lors du perçage pour l’installation du kit

upgrade LED. Vérier les ls et composants.

5. WARNING – Risk of re or electric shock. Check the existing wiring for damage before installing Upgrade Kit. Do not install if existing

wires are damaged.

ATTENTION- Risque d’incendie ou de choc électrique. Vériez si le câblage existant n’est pas endommagé avant l’installation du kit upgrade LED.

Ne pas installer si des ls sont endommagés.

6. WARNING – To prevent wiring damage or abrasion, do not expose wires to the edge of sheet metal or any other sharp objects.

ATTENTION - Pour éviter les dégâts de câblage par l’abrasion, ne pas mettre en contact les ls électriques avec des bords de tôle ou d’autres

objets pointus.

7. WARNING – Risk of re or electric shock. Install this kit only in the luminaires that have the construction features and dimensions shown

in the photographs and/or drawings.

ATTENTION - Risque d’incendie ou de choc électrique. Installez ce kit seulement dans les luminaires qui ont les caractéristiques de construction et

les dimensions dans les photographies ou les dessins de la page suivante.

8. Do not make or alter any holes in a wiring enclosure or electrical components during the kit installation.

Ne pas modier ou faire de trous dans une boite de câblage ou compartiment électrique lors de l’installation du kit.

9. Ensure that the existing luminaire is installed according to original manufacturer’s specication.

S’assurer que les luminaires sont installés selon les spécications du fabricant.

10. Only the holes indicated in the photographs or drawings may be made or altered as a result of the kit installation. Do not leave any other

holes open in a wiring enclosure or electrical component.

Seulement les trous indiqués dans les photographies ou les dessins peuvent être faits ou altérés pour l’installation du kit LED. Ne laissez aucun

trou ouvert dans le compartiment électrique.

11. Once the Upgrade Kit is installed, the luminaire can no longer accept HID lamps and shall not be converted back to an HID luminaire.

Une fois le kit upgrade LED installé, l’appareil peut ne plus accepter les lampes HID et ne pourra pas être retransformé en luminaire HID.

12. No user maintenance is required. Do not remove the enclosure cover after installation.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

HOUSING SIZES:

NOTE: Ensure the sizes of the existing luminaire housings are

approximately as follows:

Richmond: 21-3/5”L X 12”W X 13-4/5”H

Whiteway Civic: 20-9/10”L X 10-9/10”W X 13-2/5”H

*This fixture must be surface mounted

UPGRADE KIT LIST OF COMPONENTS:

NOTE: This kit is used only with the standard CPY250

luminaire that is sold separate from the kit.

1. Upgrade assembly Panel

2. (8) - Mounting screws

3. (4) - Nuts

4. (4) - Sealing Washers

5. (2) - Hooks

6. (2) - 9" Cable

2 of 2 CI391X05R1_A

www.creelighting.com

subject to change. See www.creelighting.com/warranty for warranty and specifications. Cree® and the Cree Lighting logo are

registered trademarks of Cree, Inc. NEMA® is a registered trademark of the National Electrical Manufacturers Association.

TO INSTALL:

NOTE: DO NOT lift luminaire by the power leads.

STEP 1:

Disconnect power to fixture.

STEP 2:

Verify the existing housing model.

STEP 3:

Open and remove lens frame assembly. Remove door mounting hardware,

lamp, reflector, ballast cover and socket assembly. Disconnect incoming power

leads.

Note: Existing ballast and capacitor may be left in fixture if they do not

interfere with the LED upgrade module and if the existing luminaire is not

supported solely by the j-box. If removed, components should be recycled

according to all local, state, and/or federal ordinances.

STEP 4:

Check the caulk between the Canopy and the existing luminaire housing. Add

caulk as needed to ensure water tight installation.

STEP 5:

Locate the center of the right side housing flange and pre drill (2) holes 12”

apart using a 1/4” bit. See Figure 1 and 2.

STEP 6:

Attach CPY250 luminaire and the provided cables to the panel using the (4)

supplied machine screws and nuts as shown in Figure 2. These cables will

allow for hands-free wiring and support during installation.

STEP 7:

Attach (2) hooks on ends of cables to the holes drilled in Step 3 on housing

flanges. See Figure 3.

STEP 8:

Make wiring connections as shown in the Electrical Connections Section.

NOTE: Ground connection should include previous luminaire ground. Verify

that the supply voltage is within the fixtures voltage rating.

STEP 9:

Rotate panel to horizontal position and push upward into the existing luminaire

housing ensuring that no wires are pinched. Slide panel bracket over housing

flange. Once positioned, secure to housing using (4) supplied mounting screws

and sealing washers, ensure the rubber side of the washers is towards the

panel. See Figure 3.

ELECTRICAL CONNECTIONS

STEP 1:

Using 90°C minimum rated wire connectors, make the following electrical

connections:

a. Connect supply ground conductor to fixture (green) ground wire and mounting

plate (green) ground wire with wire connector.

b. Connect supply voltage conductor to fixture black wire with wire connector

c. Connect supply neutral conductor to fixture white wire with wire connector.

d. If Dimming is an option; connect the violet dimming positive lead to the supply

dimming positive lead.

e. If Dimming is an option; connect the pink dimming negative lead to the supply

dimming negative lead

LINE

OR HOT 1

GREEN

LINE-BLACK

GROUND-GREEN

NEUTRAL-WHITE

DIM (-) PINK

DIM (+) VIOLET

NEUTRAL

OR HOT 2

VIOLET

PINK

SUPPLY WIRING

(DIMMING OPTIONAL)

LUMINAIRE

Housing Flange

Panel

(4) Supplied Screws

Panel Bracket

(4) Supplied

Mounting Screws

CREE LIGHTING CPY250 Richmond Civic Upgrade Kit Guide d'installation

Marque: CREE LIGHTING

Modèle: CPY250 Richmond Civic Upgrade Kit

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: CREE LIGHTING CPY250 Richmond Civic Upgrade Kit Installation guide

CREE LIGHTING CPY250 Richmond Civic Upgrade Kit Guide d'installation

CREE LIGHTING CPY250 Richmond Civic Upgrade Kit Guide d'installation

dans d''autres langues

Documents connexes

Autres documents