EVBox BusinessLine Manuel utilisateur

Taper
Manuel utilisateur
1
EN
manual
BusinessLine
2
EN
Meet BusinessLine!
Let’s get started.
EN
manual
BusinessLine
4
EN
General
Errors or Inaccuracies
Communication Regulations (FCC)
Americans with Disabilities Act (ADA) Compliance
Product and environmental characteristics
Safety regulations
Warnings
Cautions
Remarks
Transport and storage
Product description
Meet BusinessLine
Components & features
Networking your station
BusinessLine Smart Charging features
Operation
Charging with a QR code
Charging with an RFID card
LED ring chart
Warranty
6GEJPKECNURGEKƂECVKQPU
Inside the box
Installation
Safety requirements
Planning the installation
Pre-installation checklist
Installation steps
Post-installation checklist
Maintenance
Installing the communication module externally
Adding a Satellite station to a Hub
Troubleshooting
Warranty
Declaration of conformity
5
5
5
5
5
6
6
6
7
7
8
8
9
10
10
11
11
11
12
12
13
14
15
15
15
16
17
31
31
32
33
35
36
37
Table of contents
5
EN
General
Errors or Inaccuracies
For any inaccuracies or omissions, or to provide feedback and suggestions, send an email to
Communication Regulations (FCC)
This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) This device may not
cause harmful interference and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Americans with Disabilities Act (ADA) Compliance
While single-family residential installations do not have complex parking requirements,
commercial, public and multi-unit residential installation have additional parking considerations
that include Americans with Disabilities Act (ADA) accessible EVCS spaces and meeting
the minimum requirements for spaces in parking lots and facilities. EVCS site hosts often
experience challenges in providing ADA accessible EVCS spaces in addition to standard EVCS
spaces while maintaining the minimum requirements for parking. Consideration of the available
parking is important for residents as well as employers and employees. Installing charging
in unassigned spaces or common areas for availability to all residents at MUDs requires
compliance with ADA accessibility regulations.
Please check with your State and Local government agencies to understand and implement the
necessary accommodations for people with disabilities.
Product and environmental characteristics
/iV>À}}ÃÌ>Ì>ÃLiiViÀÌwi`LÞÌi>Õv>VÌÕÀiÀ>`Li>ÀÃÌi}°/i
relevant declaration of conformity may be obtained from the manufacturer.
/iV>À}}ÃÌ>Ì>ÃLii1ViÀÌwi`LÞÌi>Õv>VÌÕÀiÀ>`Li>ÀÃÌi1}vÀ1-Ƃ
and Canada. The relevant declaration of conformity may be obtained from the manufacturer.
The charging station complies with the RoHS Directive (RL 2011/65/EU). The relevant
declaration of conformity may be obtained from the manufacturer.
Electrical and electronic appliances, including accessories, must be disposed of separately from
the general municipal solid waste. Recycling of materials saves raw materials and energy and
makes a major contribution to conserving the environment.
E481618
6
EN
Safety regulations
Warning: risk of electric shock
Please read the documentation provided with the charging station to familiarize yourself
with the safety instructions and directions before you use the charging station.
In the event of danger and/or accidents, have the charging station disconnected
immediately by an electrician or facility manager.
Do not operate the charging station if it, or the charging cable, is physically cracked,
frayed, or otherwise visibly damaged. Please consult an EVBox employee, the distribution
V«>Þ>`ÉÀ>µÕ>wi`iiVÌÀV>À}Ì>Ü>Þ°
Ì`ÀiVÌ«ÜiÀvÕiÌÃvyÕ`ÃÌÌiV>À}}ÃÌ>Ì]>`iÛiÀ«iÀ>ÌiÜÌÜiÌ
hands. Do not submerge the EV plug into liquids.
Please carefully read our instructions and the vehicle’s operating instructions in your
owners handbook before charging your electric vehicle.
Failure to follow these guidelines may result in serious injury or even death.
Warning: Turn off input power to your charging station at the circuit breaker panel before
servicing or cleaning the unit. Be sure the station is powered off until the cover is properly in
«>Vi° iÛiÀ`ÀiVÌ«ÜiÀvÕiÌÃvyÕ`ÃÌÞÕÀV>À}}ÃÌ>Ì>`iÛiÀ«iÀ>ÌiÌi
charging station with wet hands.
Cautions
Use this charging station for mode 3 compatible electric vehicles with an SAE-J1772
charge port only. Refer to your vehicle’s owner manual to determine the suitable plug
type(s).
This product may impact the operation of implanted electronic medical devices. Before
operating the charging station check with the supplier of the electronic medical device if
ÌÃ«iÀ>ÌV>LiyÕiVi`LÞV>À}}ivviVÌð
The charging station is powered by high currents. Always switch off power at the circuit
breaker before installing, maintaining or servicing the product.
/ÃV>À}}ÃÌ>Ì>ÞÞLiÃÌ>i`]>Ì>i`>`Ài«>Ài`LÞµÕ>wi`
personnel.
This product contains no user serviceable parts. Consult EVBox or your distributor for
more information. Please do not attempt to service or repair the charging station yourself
Incompetent installation or repairs may result in danger to the user and could result in
warranty void.
Do not install a faulty charging station or a station with a noticeable issue. For instructions
on installation, see page 17.
Be sure that the charging station or the charging cable never come into direct contact
with a heat source.
Ensure that the equipment is used under the correct operating conditions (see “Technical
ëiVwV>Ìû«>}i£Î®°
ÌÕÃiiÝ«ÃÛiÀÀi>`Þy>>LiÃÕLÃÌ>ViÃÌiÛVÌÞvÌiV>À}}
station.
Persons unable to assess the dangers involved in operating a charging station should not
use the charging station.
7
EN
Do not allow children to operate this device. Adult supervision is required when children
are in the proximity of a charging station in use.
Make sure the charge cable is positioned so it will not be stepped on, driven over, tripped
over, or otherwise subjected to damage or stress.
Be sure that the charging cable is not kinked or jammed.
While charging, the cable must be completely unwound and connected to the
vehicle without overlapping loops (this is to avoid the risk of the charging cable from
overheating).
Always pull on the plug’s hand grip and never on the charging cable itself.
Always store the EV plug in its designated EVBox dock.
Ì«>Viw}iÀÃÀÌiÀLiVÌÃÃ`ivÌiV>À}}«ÀÌÀ«Õ}«ÀÌ°
Remarks
This charging station has been designed and tested in accordance with international
standards.
This charging station must be used exclusively for the purpose intended.
These directions for use are valid for different models of the charging station. It is possible
that a number of features are described that may not be applicable to your charging
station.
The charging station complies with Safety Class I (the charging station is supplied with a
ground terminal for safety) and voltage Category III.
Do not modify the charging station in any way. This will result in loss of warranty and
liability, and may lead to dangerous circumstances.
Note: Some electric vehicles require an external ventilation system to prevent the
accumulation of hazardous or explosive gasses when charging indoors. Consult the vehicle’s
owner manual to determine whether or not your electric vehicle requires ventilation during
charging. This charging station is not designed for charging these vehicles and must not be
used for charging electric vehicles that require external ventilation.
Transport and storage
Ensure that the main power source has been disconnected when storing or transporting the
charging station. No liability can be accepted for damage during the transportation process if
the charging station is transported in anything other than its original packaging.
Store the charging station in a dry environment. The product is preferably stored at room
temperature. If this is not possible, storage temperature must be between 60°F and 110°F with
a maximum humidity level of 95% non-condensing.
8
EN
Product description
Meet BusinessLine
The EVBox BusinessLine is a commercial-grade charging station capable of charging all J1772
mode 3 compatible (plug-in) electric vehicles.
Ƃ6ÝÕÃiÃÃiV>À}}ÃÌ>ÌÃ>ÀiºÕVi`»>`ÕÃi"**"«i>À}i*Ì
*ÀÌV®ÌiÃÕÀiÌ>ÌÌiÞiÛiÀLiViÃÌÀ>`i`>ÃÃiÌð/iÞV>LiVw}ÕÀ>Ìi`ÌÀÕ
>Þ"**ÃiÀÛVi«ÀÛ`iÀÃiiº iÌÜÀ}ÞÕÀÃÌ>Ì»«>}i£ä®°/iÃÌ>ÌV>>Ã
LiVw}ÕÀi`ÌÀÕÜÌÕÌ>ÞÃiÀÛVi«ÀÛ`iÀ>Ì>°
All BusinessLine charging stations are equipped with a number of Smart Charging features,
i>`>>V}]*i>->Û}]>`ÕLÉ->ÌiÌiVw}ÕÀ>ÌÃiiºÕÃiÃÃi->ÀÌ
>À}}vi>ÌÕÀiû«>}i£ä®°/iÃivi>ÌÕÀiÃÀi`ÕViÌi>ÕÌv«ÜiÀÕÃi`ÌV>À}i
ÛiViÃ`ÕÀ}ëiVwi`Ìi]ÌiÀiLÞâ}VÃÌÃÜi«ÀÛ`}ÌiLiÃÌV>À}}
experience.
The EVBox BusinessLine is made with safety and user-experience as our top priorities.
Ƃ6ÝV>À}}ÃÌ>ÌÃ>ÀiViÀÌwi`Ã>vivÀLÌ`À>`ÕÌ`ÀÃÌ>>ÌÃ]
and function optimally in an ambient temperature anywhere between -22°F and +130°F
1ViÀÌwi`vÀÓÓ°F to +104°F) with a maximum humidity level of 95% non-condensing.
EN
Components & features
LED Ring
The iconic LED ring.
BusinessLine’s smart status
indicator makes clear what
the BusinessLine is doing at
all times.
3.
Operating System
BusinessLine can be
networked via an optional
UMTS modem, allowing
users to start and stop their
charging session remotely via
>"**L>VvwVi>`>
mobile app.
1.
2.
Card reader
This is the area where you
scan your charge card or
key fob. The BusinessLine
reads the data from your card
to start or stop a charging
session.
4.
Charging cable
BusinessLine charging plug
J1772 is compatible with
electric vehicles that can
handle capacities from 3.7kW
up to 7.4kW.
9
1
2
3
4
10
EN
Networking your station
The smart charging station is equipped with a RFID card reader, a kilowatt-hour meter, and
a UMTS/GSM/GPRS/GPS communication module. These components together provide the
authorization and communication of the charging session procedure with the central system
L>VvwVi®vÀ«ÀViÃÃ}>`ÃiÌÌiiÌvÌiÌÀ>Ã>VÌÃ>ÃÀiµÕÀi`°
EVBox stations are compatible with any OCCP service provider. A GSM/UMTS network
connection link with the connected charging station is essential for the smart charging
station to function properly. However, a good link cannot always be obtained in enclosed
spaces (i.e., a closed or underground parking garage). In cases like this, the communication
module should be positioned externally from the charging station along with the GSM/GPS
antenna, and connected to the controller on the inside of the charging station. The external
communication module cabinet and required connectors are sold separately through EVBox or
your distributor (for more information go to page 32).
ƂÕÃiÃÃiÃÌ>ÌÃViºÕVi`»>ÃÌiÀ`iv>ÕÌ]i>}ÌiV>À}}ÃÌ>Ì>Ã
no commitment to a networking plan. Optionally, you can add network services at any point in
time, thereby enhancing your stations’ Smart Charging capabilities, and open yourself up to a
whole new network of EV drivers.
BusinessLine Smart Charging features
Smart Charging allows you to maximize your charging infrastructure and get the most out of
your investment. This has been key to our continued success and is a true differentiator in the
world of Electric Vehicle Service Equipment (EVSE). Below are BusinessLine’s three primary
Smart Charging features:
*WD5CVGNNKVGEQPƂIWTCVKQP
"«iÀ>ÌiÕÌ«iV>À}}ÃÌ>ÌÃVÃÌivviVÌÛiÞÜÌÌiÕLÉ->ÌiÌiVw}ÕÀ>Ì]
which connects a group of charging stations per location to each other through a single
VÕV>Ì`iÛVi°>ÀÀÞ}Õ«ÌÓäV>À}}«ÌÃ]ÌÃVw}ÕÀ>ÌvviÀÃÌÞ>
Ài`ÕVi`«ÀViº->ÌiÌi»ÃÌ>ÌÃ]LÕÌ>Ã>ÜÃÞÕÌ«iÀ>ÌiÞÕÀVÕÃÌiÀvViVÌi`
charging stations while only paying for one subscription plan.
Load Balancing
Load Balancing makes sure you never overdraw your building’s capacity by spreading the
available power between the charging stations, allowing you to accommodate as many drivers
>Ã«ÃÃLi°9ÕV>>Ì>Ã>vi>`ivwViÌV>À}}>Ì>ÌiÃÜiii«}VÃÌÃÜ°
Peak Shaving
Prevent high building demand charges with Peak Shaving. This service allows you to set up a
>ÝÕV>«>VÌÞvÀÞÕÀV>À}}ÃÌ>ÌÃÜÌëiVwVÌivÀ>ið/ÃÜ>Þ]ÞÕiÃÕÀi
that you won’t exceed the desired limits of your property, keeping operational costs low.
11
EN
Operation
A charging session may be started using a RFID card or a QR code (depending on
network operator support).
The charging station is equipped with a self-testing internal residual current leakage
detection device that will stop the charging process if current leakage (AC or DC) is
detected.
Charging will only start if the charging cable is properly (securely) connected to the
iiVÌÀVÛiVi°-i`iÃ>ÀiVw}ÕÀi`ÌÃÌ>ÀÌV>À}}>ÕÌ>ÌV>ÞÜiÌi
charging cable is properly (securely) connected to the vehicle.
Charging at a station using a QR code for networked units
1. Download the network providers’ app to your smartphone and sign up
wÀÃÌÌiÕÃiÞ®°
2.*ÀÛ`iÌiÀiµÕiÃÌi``iÌ>Ãv>««V>Li]wÀÃÌÌiÕÃiÞ®°
3. Connect your vehicle to the charge port.
4. Scan the QR code using the mobile app, or manually enter the charge station ID located
on the QR label to start charging.
5. To stop charging, unplug the charging cable and insert the charging plug into the
holster for the next user.
Charging at a station using a RFID card or a key fob
1. Connect your vehicle to the charge port.
2. Hold an authorized RFID card or key fob (Mifare Classic, 13.56Mhz) against the front of
the charging station at the round surface showing a hand with a card (see image below) to
start the charge.
3. After scanning, the station will blink green for a few seconds while it registers your card.
Once the ring turns solid blue, the charging session is initiated.
4. To stop charging, unplug the charging cable and insert the charging plug into the
holster for the next user.
Start Stop
Start Stop
12
EN
The LED ring mounted around the cable dock shows the status of the charging station so that
you can see which mode the charging station is in.
Warranty
EVBox North America warranties its equipment and software against errors and defects in
materials and workmanship for thirty-six (36) months from the date of delivery, during which
time it will provide support to diagnose and repair the errors, if any. However, any such
problems encountered out of any causes that are not attributable to EVBox shall be at the
customer’s risk and account (for more detail check the warranty section, see page 36).
What you see What it means What to do
LED off
or green
Station is ready for use. Plug the station’s charging cable
into the car.
LED green
y>Ã}
Your charge card or ID
ÃLi}ÛiÀwi`°
Wait until LED turns blue.
LED yellow The car is fully
charged.
Unplug the station’s charging cable
from the car and re-insert the cable into the
cable dock.
LED yellow
y>Ã}
Station is awaiting
communication from
the car
Wait until LED turns blue.
LED blue Station is charging the car. The car is charging.
LED red Station is experiencing
an error.
Contact our Support Desk via
LED red
y>Ã}
Your charge card is not
authorized to charge.
Contact your charge card service
operator, or vontact our Support Desk via
13
EN
Technical ëiVwV>ÌÃ
ÃÌi`LiÜ]>ÀiÌi}iiÀ>ëiVwV>ÌÃvÀÌiÕÃiÃÃi°9ÕV>w`Ài`iÌ>Ã>LÕÌ
ÌiÌiVV>ëiVwV>ÌÃvÀ>ëiVwV`iÌiº-«iVwV>ÌûÃiVÌv6ÝÕð
Technical Features
Charging capacity per connector 7.4 kW
Connector type SAE J1772
Number of connectors 1 or 2
iÀÌwV>Ì UL, CE, CUL
Power output 1-phase or 2-phase, 208V-240V, 32A
Temperature range (F) -22°F to +130°F 1ViÀÌwi`vÀÓÓcÌ³£ä{°F)
Temperature range (C) -30°C to +55°C (1ViÀÌwi`vÀÎäcÌ³{ä°C)
Humidity (non-regulating) Max. 95%
Max. Installation height +6,500 feet above sea level
Authorization Keyfob / RFID card / Mobile App
Communication GPS / GSM / UMTS / GPRS Modem / Controller with RFID reader
Communication Protocol OCPP 1.2, 1.5, 1.6S and 1.6J
Payment Via service provider
Physical Features
Designed according to IEC 61851-1 (2010), EC 61851-22 (2002)
Protection NEMA-3R
Installation standards EN 1010, IEC 61851-1 (2010), IEC 61851-22 (2002), IEC 60364-4-41 (2007),
EN 62196-1 (2003), EN 60335-1 (2012), AC (2014)
Housing Polycarbonate
Dimensions (in) 10 x 8 x 24 in (L x W x H) - Single
10 x 16 x 24 in (L x W x H) - Double
Dimensions (mm) 255 x 205 x 600 mm (L x W x H) - Single
255 x 410 x 600 mm (L x W x H) - Double
Weight (lbs) 35 lbs (max.) - Single
60 lbs (max.) - Double
Weight (kg) 16 kg (max.) - Single
28 kg (max.) - Double
Mounting Wall, pole, or retractor system
Standard colors White (RAL 9016), Dark grey (RAL 7016), Blue (RAL 5017),
Dark green (RAL 6007), Light green (RAL 6024)
Cable (ft) 18 or 25 ft cable (SAE J1772)
Cable (m) 6 or 8 meter cable (SAE J1772)
14
EN
MANUAL
Inside the box
1 EVBox BusinessLine unit
Single or Double connector
2 Allen key to open the cover of the unit
3 Installation manual
1
3
2
15
EN
Installation
Safety requirements
iVÌ}>`ÃÌ>}ÌÃ«À`ÕVÌÕÃÌLi`iLÞ>µÕ>wi`iiVÌÀV>°/iÜiÀÀ
facility manager is responsible for the installation, operation, and maintenance of the charging
station, whereby both the law regarding the safety of persons, animals and property must be
observed, as well as the installation instructions enforced in the country of use.
Read the safety instructions before you start working on the installation.
Ensure the correct supply voltage/power and ensure that the meter cabinet is properly
secured.
Before shipment, each EVBox charging station is checked for correct connections and the
charging station is operationally tested.
Before switching on the charging station, check that the power source available
VÀÀië`ÃÌÌiVw}ÕÀ>ÌÃiÌÌ}ÃvÌi«À`ÕVÌ>Ã`iÃVÀLi`Ìi>Õ>°
Check that all connectors are properly seated on the controller unit. (All stations are
checked on this parameter before they leave our factories, but in rare instances, a
connector can become loose or disconnected due to unforeseen transport conditions).
Ensure that the equipment is used under the correct operating conditions.
Never operate the product in wet, dusty or explosive surroundings.
ÃÕÀiÌ>ÌÌiÀiÃ>Ü>ÞÃ>`iµÕ>Ìië>Vi>Ìi>ÃÌn»®ÃÕÀÀÕ`}Ìi«À`ÕVÌvÀ
ventilation purposes.
Planning the installation
Minimum requirements
Each unit MUST be connected with its own dedicated power line, for a BusinessLine
Double you need to run 2 power feeds.
Calculate the existing electrical load to determine the maximum operating current.
Calculate the distance to ensure minimal voltage drop.
"LÌ>>ÞiViÃÃ>ÀÞ«iÀÌÃvÀÌiV>>ÕÌÀÌÞÌ>Ì>ÃÕÀÃ`VÌ>`VwÀ
Ì>ÌÌivÜÕ«ëiVÌ>ÃLiiÃVi`Õi`LÞ>µÕ>wi`iiVÌÀV>>vÌiÀÌi
installation is complete.
Use only copper conductors.
Use conductors that are sized in accordance with local wiring regulations. The selected
cable gauge must be able to sustain periods of a constant load up to 40A.
Each unit should have its dedicated 40A circuit breaker.
The charging station is set to charge at a maximum current of 32A by default, requiring a
40A upstream circuit breaker. The maximum allowable current can be decreased according
Ì>Û>>Li>«iÀ>}i°/ÃÕÃÌLiVw}ÕÀi`ÃÌiLÞ>ÌiVV>]ÀÀiÌiÞvÀ>
networked station. EVBox highly recommends planning your installation for 32A current.
Make sure the maximum current settings are correct.
16
EN
Location
Position the charging station, where possible, in surroundings not subject to extreme conditon
and where it’s not prone to damage. The charging station can either be installed against a
sturdy wall or on the optional stainless steel pole. To accommodate wall mounting, a wall
mount bracket is available as an option. Consult EVBox or your distributor for more details.
Pre-installation checklist
The conduits are laid and the correct gauge copper wires are used for installation
Cellular network connectivity at the location is good
Current capacity of the site is already known (Amps)
Required tools are availlable – we recommend a mini ratchet for tight areas
ƂiiVÌÀVÛiViÀ>6-ÌiÃÌiÀÃ>Û>>LiÌwÃÌiÃÌ>
The mounting option is selected and necessary provisions are made
All the units and accessories ordered are delivered, inspected and free of damage
17
EN
Step 1: Running the power supply cable
The maximum power rating for the each connector is 7.4 kW or 32A at 240V AC (single or split
phase). Run a power line from the main circuit board with an appropriately rated circuit breaker.
Use a conduit to run the power line to the charging station. The power line enters the station
via the backplate in the case of a single station and through the pole for double stations.
Note: BusinessLine Double stations need two separate power cables with separate circuit
breakers.
1.1 Disassemble the cover(s). They are attached to the underside of the charging station
with two hex bolts. For this, use the hex key (5mm - metric) provided with
the charge station. When mounting the charging station to a wall, the free working space
behind the station is limited, for these situations we recommend using a 5mm
VÀÀ>ÌViÌ°-iiºÜÌ«iÌiVÛiÀî»>LÛi®vÀÕÃÌÀ>Ìð
2. Use the allen key provided to unscrew
(as shown in the image).
1. Locate the two screws at the bottom of the
unit (four screws for the dual unit).
3. Open the cover from the bottom as shown.
Installation steps
How to open the cover(s)
18
EN
1.2 The power cable enters the station through the central opening on the back plate or
through the pole.
1.3 The power connector terminal is located at the top of the station. Make sure the power
supply cable extends out at least 2.5 ft so as to comfortably reach the terminal block.
Step 2: Installing the mounting options
2a. Mounting the CombiPole
EVBox charging stations can be mounted onto a pole. To do this, EVBox offers two types
of Combipole
- Inground (PN# 290150)
- Surface mounted (PN# 290305)
BusinessLine Single stations are to be attached to the CombiPole by using the
BusinessLine Adapter Kit (PN# 290165) (image below).
The BusinessLine Double stations can be mounted directly on the CombiPole without an
additional adapter kit required.
Mounting the Adapter Kit onto the CombiPole (BusinessLine Single only)
Using the 2 X M5x40 bolts, attach the adapter to the CombiPole as shown on the
following page
Partially mount the 2 X M5x16 bolts on the adapter kit
The 2 X M5x16 bolts will be used to mount the unit onto the adapter kit and hence,
should only be partially screwed in. They are tightned after the unit is mounted.
Surface Mounted:
CombiPole (PN# 290305) can be mounted onto a concrete surface.
/i«iÃÕÌi`ÜÌvÕÀLÌÃÌÃiVÕÀiÌi«i>VVÀiÌiyÀ°
/iL>Ãi«>Ìii>ÃÕÀiÃn»Ýn»ÜÌvÕÀiÃÓxÉÈ{»`>iÌiÀ®vÀ>ÌÌ>ViÌ°
Inground:
CombiPole (PN# 290150) can be mounted in soil or dirt.
Dig a hole approximately 2.5 feet deep and 10 inches wide.
Ensure that the mounting holes for securing the charging station are in the correct
position with respect to the parking space(s) and align the pole (PN# 290150) vertically.
Use well-known best practices to solidify the poles foundation.
19
EN
2x socket bolt M5x16
2x Counter hex head bolt M5x40
1x Circular insert cap
To see how to mount your station to the CombiPole, skip ahead to
page 22.
2b. Mounting on a wall
Mounting a BusinessLine Single
A wall spacer is used to mount a Single BusinessLine onto a
wall.
Ãi>Ã`>`y>ÌÛiÀÌV>ÕÌ}ÃÕÀv>ViÌÃÌ>Ìi
wall spacer. PN#290190 (The wall should be able to take upto
80lb weight)
ÀiÃÌÌiy>ÌÃÕÀv>ViÌÃÌ>ÌiÜ>ë>ViÀÕÃ}
the holes (A) on the wall spacer.
Power supply conduit can enter the unit through the
top,bottom or side of the wall soacer
Lead the power cable out of the hole on the wall spacer, the
EVBox BusinessLine will mount onto the wall spacer.
A wall mount cable wrap is also provided for cable
management.
Mounting a BusinessLine Double
A wall mount bracket is used to mount a BusinessLine Double onto a wall.
Ãi>Ã`y>ÌÛiÌV>ÕÌ}ÃÕÀv>ViÌÃÌ>ÌiÜ>LÀ>ViÌ°* ÓäÈää/i
wall should be able to take up to 100lb weight).
Drill holes onto the wall, alligning it with the holes on the plate on the wall spacer as
shown in illustration above.
Power supply cables enter the bracket as shown in the illustrations on the following page.
Lead the power supply cable all the way through the bracket, the BusinessLine Doule
slides onto the bracket.
To see how to mount your station to the wall bracket, skip ahead to Pole mounting for
BusinessLine Double on page 23.
20
EN
EVBox BusinessLine Single units can also be mounted onto
a taller post which provide supperior cable management.
The system doesn’t let the charge cable touch the ground,
making the install safer as well as increasing the lifespan of
the charge cable (PN# 290152).
Two types of posts available
- For one single unit (mounted on one
side) – 290152S
- For two single units (mounted on two
sides) – 290152D
The retractor system consists of two (2) parts — the
retractor post and retractor box. The box is mounted on
the top if the post using the predrilled holes.
- Retractor Box – 290151
Note: To mount 2 units, 2 retractor
boxes need to be mounted on opposite
sides.
2c. Mounting on a retractor cable management system
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

EVBox BusinessLine Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues