INVT EVC Series Manuel utilisateur

Taper
Manuel utilisateur
Electric Vehicle AC Charger
EVC Series (NA) - User Manual
WARNING WARNING
USER MANUALUSER MANUAL
0201
Circuit Breaker Options table
Output Amperage (A)
Circuit Breaker Options (A)
16A
20A
32A
40A
40A
50A
48A
60A
Circuit Breaker Options table
Output Amperage (A)
Circuit Breaker Options (A)
16A
20A
32A
40A
40A
50A
48A
60A
1. Important Safety Instructions
WARNING – This manual contains important instructions for Models:
EVC10 series that shall be followed during installation, operation and maintenance of the unit.
1) Read all the instructions before using this product.
2) This device should be supervised when used around children.
3) Do not put fingers into the electric vehicle connector.
4) Do not use this product if the flexible power cord or EV cable is frayed, has broken insulation,
or any other signs of damage.
5) Do not use this product if the enclosure or the EV connector is broken, cracked, open, or
shows any other indication of damage.
6) To reduce the risk of fire, connect only to a circuit provided branch circuit over-current
protection in accordance with the CSA C22.1–15 Canadian Electrical Code, Part 1 (Canada) or
NOM-001-SEDE Electrical installations (utility) (Mexico) or ANSI / NFPA 70 National Electrical
Code (USA).
7) To avoid a risk of fire or electric shock, do not use this device with an extension cord.
8) THE SUITABILITY OF THE USE OF FLEXIBLE CORD IN ACCORDANCE WITH CE CODE,
PART I, RULE 4-012, IS TO BE DETERMINED BY THE LOCAL INSPECTION AUTHORITY
HAVING JURISDICTION.
9) Risk of electric shock. Do not remove cover or attempt to open the enclosure. No user
serviceable parts inside. Refer servicing to qualified service personnel.
AVERTISSEMENT – Ce manuel contient des instructions importantes pour les modèles :
série EVC10 qui doit être suivie pendant l'installation, le fonctionnement et la maintenance de
l'unité.
1) Lisez toutes les instructions avant d'utiliser ce produit.
2) Cet appareil doit être surveillé lorsqu'il est utilisé à proximité d'enfants.
3) Ne pas mettre les doigts dans le connecteur du véhicule électrique.
4) N'utilisez pas ce produit si le cordon d'alimentation flexible ou le câble EV est effiloché, a
une isolation cassée, ou tout autre signe de dommage.
5) N'utilisez pas ce produit si le boîtier ou le connecteur EV est cassé, fissuré, ouvert ou
montre toute autre indication de dommage.
6) Pour réduire les risques d'incendie, ne connecter qu'à un circuit protection contre les
surintensités des circuits de dérivation conformément à la norme canadienne CSA C22.1-15
Code électrique, partie 1 (Canada) ou NOM-001-SEDE Installations électriques (service public)
(Mexique) ou ANSI / NFPA 70 National Electrical Code (États-Unis).
7) Pour éviter tout risque d'incendie ou de choc électrique, n'utilisez pas cet appareil avec une
rallonge.
8) L'ADÉQUATION DE L'UTILISATION DU CORDON FLEXIBLE SELON LE CODE CE,LA
PARTIE I, RÈGLE 4-012, DOIT ÊTRE DÉTERMINÉE PAR L'AUTORITÉ LOCALE D'INSPEC-
TION AYANT JURIDICTION.
9) Risque de choc électrique. Ne retirez pas le couvercle et n'essayez pas d'ouvrir le boîtier.
Aucun utilisateur pièces réparables à l'intérieur. Confiez l'entretien à un personnel d'entretien
qualifié.
WARNING 2. Basic Interface
SAE J1772
AC Charging
Connector
Rear Notch
Charging Cable Inlet AC Power Inlet
LAN Cable Inlet
USER MANUALUSER MANUAL
0403
LED Light
Indication
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference, and this device must accept any interference
received, including interference that may cause undesired operation.
Caution: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
To satisfy FCC RF exposure requirements, a separation distance of 20cm or more should be
maintained between the antenna of this device and persons during device operation. To ensure
Note: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interfer-
ence to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at
his own expense.
WIFI module Contains FCC ID:2AC7Z-ESPWROOM32
LTE module Contains FCC ID:XMR201909EC25AFX
compliance, operations at closer than this distance is not recommended.
3. Dimensions
5.1″
9.8″
13.8″
4. Design Standard
USER MANUAL USER MANUAL
0605
UL 2594: Electric Vehicle Supply Equipment
UL 2231-1: Personnel Protection Systems for Electric Vehicle (EV) Supply Circuits: General
Requirements
UL 2231-2: Personnel Protection Systems for Electric Vehicle (EV) Supply
Circuits: Particular Requirements for Protection Devices for Use in Charging Systems
UL 2251: Plugs, Receptacles and Couplers for Electric Vehicles
UL 62: Flexible Cords and Cables
UL 991: Tests for Safety-Related Controls Employing Solid-State Devices
UL 1998: Software in Programmable Componets
NFPA 70 Article 625: National Electrical Code, Electric Vehicle Charging System
UL 840 (Clearance and Creepage)
4.8″
4-Φ0.35″
2.83″
5. Specification
*1 LAN Version or Wi-Fi Version or 4G Version
*2 Wi-Fi Version
*3 4G Version
Model Name
Rated Input Voltage
Rated Output Current
AC Power Frequency
Input Protection
Output Protection
Output Interface
Storage Temperature
Operation Temperature
Relative Operation Humidity
Relative Storage Humidity
Version
RJ45 Cable Inlet*1
Wi-Fi Function*2
4G Fnction*3
Cable Length
Protection Level
Installation Type
Altitude
Status Indication
-40°F to 158°F
-22°F to 122°F
95% RH Maximum
EVC Version
200-240 VAC / Single Phase
16/32/40/48A
60 Hz
UVP, OVP, RCD, SPD, Ground Fault Protection
OCP, OTP, Control Pilot Fault Protection
SAE J1772 AC Charging Connector
95% RH Maximum
LAN Version / Wi-Fi Version / 4G Version
10M/100M Base-T
802.11 b/g/n
LTE
18ft
Type 3
Wall-Mounted
≤ 6561ft
Red, Green, Blue LED
USER MANUAL
6. Status Description of the Charger Indication Light
USER MANUAL USER MANUAL
0807
Standby - Blue Light
The READY light stays steady in
standby mode.
READY
Waiting for Charging - Green Light
After the vehicle connector is connected
to the vehicle inlet, the CHARGE light is
constantly lit.
CHARGE
Charging - Green Light Flashing
The CHARGE light flashes while
charging.
CHARGE
7. Packing List
8 Installation Instructions
8.1 Safety Requirements
• Be sure to preview the user manual and ensure local building and electrical codes are
reviewed before installing the AC charger.
• The AC charger should be installed by a qualified technician according to the user manual
and local safety regulations.
• Use appropriate protection when connecting to the main power distribution cable.
• Type B, C or D breaker with the rating current for table should be installed in the upstream
AC distribution box.
• Disconnect switch for each ungrounded conductor of AC input shall be provided by others in
accordance with the National Electric Code, ANSI/NFPA 70.
USER MANUAL
Fault - Red Light
The red light is lit while fault. Please
refer to "9.3 Error and Warning
Messages" for detailed information.
FAULT
No.
1
2
3
4
5
Product Name
AC Charger (With Charging Cable)
User Manual
Wall-Mounted Bracket
M5 teeth screws
RFID Card (RFID Version Only)
Quantity
1
1
1
2
26
M6 Hexagonal Expansion Screws 4
Note
USER MANUAL USER MANUAL
1009
RFID
1
4 5 6
2 3
Electric Vehicle AC Charger
EVC10 Series (NA) - User Manual
8.2 Installation Steps
Step 1: Use screwdriver to loosen the 13 fixed screws on the rear of charger,
then remove the front cover (for 4G Version).
Step 2: Insert the SIM card according to the picture's instruction (for 4G Version). .
USER MANUAL USER MANUAL
1211
8.3 Wiring
Step 3: Tighten 13 screws on the front cover after the front cover is put back, the
recommended screw torque is 1.0 N.m (9.6 lbf.in) (for 4G Version).
GROUNDING INSTRUCTIONS
This product must be grounded. If it should malfunction or break down, grounding provides a
path of least resistance for electric current to reduce the risk of electric shock. This product is
equipped with a cord having an equipment grounding conductor and a grounding plug. The
plug must be plugged into an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
WARNING – Improper connection of the equipment-grounding conductor is able to result in a
risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to
whether the product is properly grounded. Do not modify the plug provided with the product – if
it will not fit the outlet, have a proper outlet installed by a qualified electrician.
IAVERTISSEMENT - Une mauvaise connexion du conducteur de mise à la terre de l'équipe-
ment peut entraîner un risque de choc électrique. Vérifiez auprès d'un électricien ou d'un
technicien qualifié si vous n'êtes pas sûr que le produit soit correctement mis à la terre. Ne
modifiez pas la fiche fournie avec le produit - si elle ne rentre pas dans la prise, faites installer
une prise appropriée par un électricien qualifié.
2
3
4
5
6
7
8
9
10
11
12
13 1
2
3
4
5
6
7
8
9
10
11
12
13 1
For safe use of electricity, please add circuit breaker protection in the input part
of charging pile. Connect the L1 lead to the grid L1, connect the L2 lead to the grid L2,
connect the PE lead to the grid PE (for all Version).
Circuit Breaker Options table
Output Amperage (A)
Circuit Breaker Options (A)
16A
20A
32A
40A
40A
50A
48A
60A
USER MANUAL USER MANUAL
1413
8.4 Tools and Materials Required
Tools required before installing the Wall-Mounted charger, gather the following tools:
• Wire stripper
• Crimpers for European terminals
• Phillips screwdriver for M5
• Slotted screwdriver for 4~5.5MM
• Adjustable Wrench M6
• Head gasket screw 10-10.5mm
• Voltmeter or digital multi-meter (for measuring AC voltage at the installation site)
• The inserting cable should meet the best waterproof performance. It is recommended to use
3 core / 7AWG cable (XLPE or equivalent cable) to pull the cable from the distribution box.
• Level ruler
• Pencil or marker
• Machine drill
Installation Instructions
“This device shall be mounted at a sufficient height from grade such that the height of the
storage means for the coupling device is located between 600mm (24 inches) and 1.2m (4
feet) from grade.”
8.5 Wall-Mounted Bracket Installation
Step 2: Align the rear notch of charger into the wall-mounted bracket and fit the screw
holes of the right and left side.
Step 1:
• Set the positions of the 4 screw holes and drill them, with a diameter of 8mm and
a depth of 52mm.
• Use 4 sets expansion screw and M6 screw to fix the wall-mounted bracket on the wall.
USER MANUAL USER MANUAL
1615
Step 3:
Fix two M5 screws to complete the installation.
Overall outlook picture after installation:
Wall-mounted cable winding Optional cable hanging(optional accessory)
USER MANUAL USER MANUAL
1817
User authorization
Connect to Vehicle Charging Inlet
Charging Message
Charging completed
9. Operation Instuctions
9.1 Operating Procedures
9.2 Operating Steps
Step 1 / Standby Mode
After power-on, blue light (READY), green light (CHARGE) and red light (FAULT) all lit.
Enter standby mode and the blue light (READY) is steady on.
READY
Step 2 / Tap the RFID Card
Please plug the charging connector into the vehicle charging inlet. When you tap the
RFID card first, it needs to complete the insertion of the charging connector within 120
seconds, otherwise you need to tap the RFID card again.
Step 4 / Charging
The green light (CHARGE) turns to flash automatically, charging is in process.
• If the red light (FAULT) is lit, plug the vehicle connector again.
• If red light is still lit, please refer to "Error and Warning Messages".
CHARGE
Step 3 / Tap the RFID Card
Tap the RFID card to start the charging.
Step 5 / Charging Finished
When the charging is finished, the green light (CHARGE) is constantly lit, please
press the button on connector.
USER MANUAL USER MANUAL
2019
10. Maintenance and Repair
10.1 Daily Maintenance
Please keep the charger clean and keep the charge in a clean area with low humidity. Do not
install it in an environment near the sea, with high oil, high humidity or high dust.
• Avoid moisture or water in the charger. If there is water or moisture ingress into the charger, it
is necessary to immediately power off to avoid immediate danger, and notify the professional
personnel to carry out maintenance before next use.
• If there is any damage or dirt on the vehicle connector, charging cable, or vehicle connector
holder, please contact the maintenance personnel immediately.
• Please use the charger properly. Do not hit or press hard on the case. If the case is damaged,
please contact a professional technician.
• Avoid placing the charger near hot objects and at high temperature locations and away from
dangerous substances such as flammable gases and corrosive materials.
• Do not place external objects or heavy objects on the charger to avoid danger.
10.2 Maintenance Spares
• This charger is equipped with maintenance spares for maintenance use during and over the
warranty period. All warranty services and repairs shall be and performed by certified service
technicians authorized by Joint Technology. For details, please contact your local Joint Tech-
nology service partner or direct to our Customer Service.
10.3 Warranty and Maintenance
The warranty period for this charger is three years.
• After the event of any repair or maintenance under the warranty period, if there is no purchase
to extend the warranty service, Joint Technology shall provide a three-month warranty period
for any subsequent paid repair work.
9.3 Error and Warning Message
Remark
Auto Recover
Auto Recover
Auto Recover
Auto Recover
Auto Recover
Auto Recover
Auto Recover
Red
1 flashes followed by 3 sec pause
2 flashes followed by 3 sec pause
3 flashes followed by 3 sec pause
4 flashes followed by 3 sec pause
5 flashes followed by 3 sec pause
6 flashes followed by 3 sec pause
Flicker
Constantly Bright
Constantly Bright
Contact Customer Service
Contact Customer Service
Status
Input OVP
Input UVP
Output OCP
OTP
RCD Abnormal
Ground Fault
Control Pilot Fault
MCU Self-Test Fail
Constantly Bright Contact Customer ServiceRCD Self-Test Fail
Constantly Bright Contact Customer ServiceRelay Self-Test Fail
Constantly Bright Contact Customer Service
RCD Abnormal Stop Charging
Constantly Bright Contact Customer ServiceOutput OCP Stop Charging
OTP Stop Charging
USER MANUALUSER MANUAL
2221
• During the warranty period for any malfunction caused by normal use according to the User
Manual and Service Instruction (to be determined by certified maintenance technicians of Joint
Technology), the product shall be repaired free of charge. Except for the following situations,
the charger shall be subject to the above warranty terms:
1. The warranty certificate cannot be provided or the contents of the warranty certificate are
modified or inconsistent with the label indication of the repaired product.
2. Those who are unable to provide valid proof of purchase.
3. Those who exceed the manufacturer's specified warranty period.
4. Those who damage the product due to not following the product service instruction for use,
maintenance and storage.
5. Damage or malfunction caused by foreign object entering.
6. Unauthorized repair, disassembly or modification.
7. Damage caused by force majeure (such as lightning, excessive voltage, earthquake, fire,
flood, etc.).
8. Malfunction and damage caused by other unavoidable external factors. Malfunction and
damage caused by improper use of equipment, such as water or other solutions entering into
the equipment.
9. Malfunction and damage caused by the grid power supply and voltage which is not specified
for use with the charger equipment.
• The above guarantees shall be made solely, and no other express or implied warranties shall
be made (including the implied warranties of merchant ability, particular and applicable reason-
ableness and adaptability, etc.) whether in the contract, civil negligence, or other aspects, the
Company shall not be responsible for any special, incidental or consequential damages.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

INVT EVC Series Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues