5019 607 00188
Options
Indicative
Drying Time
Max
Load
Programmes
Gentle
Reduces Drying Intensity
(recommended for delicate items)
Spin speed
Washing Machine
rpm
800
rpm
1000
rpm
1200
Kg
Cotton
Max. 5 kg
Extra dry
95’
135’
-
80’
110’
3.5
5.0
Cupboard dry plus
85’
125’
-
70’
100’
3.5
5.0
Cupboard dry
80’
110’
-
60’
90’
3.5
5.0
Iron dry
60’
90’
-
50’
70’
3.5
5.0
Easy Care
Max. 2.5 kg
Cupboard dry plus
30’
55’
25’
45’
-
1.0
2.5
Cupboard dry
25’
45’
20’
35’
-
1.0
2.5
Iron dry
20’
35’
15’
25’
-
1.0
2.5
Airing
Laundry is aired for 30 minutes without
heating.
-----
Time Programmes
Completes drying or dries single items.
(Suitable for all fabrics).
-----
Départ Délicat
2
3
4
5
6
60’
40’
20’
7
Départ Retardé
1
2
3
4
Textile Epais
Prêt à Ranger
Prêt à Porter
Repassage
5
6
7
Prêt à Ranger
Prêt à Porter
Repassage
Coton
Synthétiques
AM 3793
Ventilation fraîcheur
Programmation électronique
MarcheFin
2h 4h
8h 6h
Entretien Filtre
Réservoir Plein
1
0
A
M 3793
Délicat
1
2
3
4
5
6
7
Start
Starts the drying cycle.
On
The indicator lamp lights up
when the dryer is on.
End
The indicator lamp lights up
at drying cycle end.
Start delay
Delays the drying cycle start
2, 4, 6 or 8 hours.
To select the start delay:
turn the programme selector
knob to the desired programme,
press the start delay button to
obtain the desired delay time.
Press the Start button.
To cancel or change the
previously set time delay: turn
the programme selector knob to
“Stop”. Door opening
interrupts the start delay.
The pump may be heard
working for a while.
Filter
The indicator lamp lights up
when the filter needs cleaning.
Clean the filter at the end of
every cycle.
Water
Container
The indicator lamp lights up when
the water container needs to be
emptied. The drying cycle is
automatically interrupted.
Empty
the water container.
Press the
Start button to restart the dryer
and continue the programme.
PROGRAMME SEQUENCE INDICATORS
Drying
Airing
Shows the status of the
programme on the knob.
Départ
Départ Retardé
2h 4h
8h 6h
Entretien Filtre
Réservoir Plein
QUICK REFERENCE GUIDE
Please also carefully read: the Instructions for Use and Installation Manual.
GB
5019 607 00188
1. Check that all fastenings are closed and that
pockets are empty.
2. Turn the articles inside out.
3. Place laundry loosely in the drum to make sure
it doesn’t become tangled.
Sort laundry as follows:
A) By care symbols
(on the collar or inside seam):
Suitable for tumble drying
Tumble drying with reduced drying intensity
only
Do not tumble dry
B) By amount and thickness/weight
Whenever the load to be dried exceeds the
dryer capacity, separate laundry according to
weight (e.g. towels from thin underwear).
C) By type of fabrics
Cotton/linen
: Towels, cotton jersey, bed and
table linen made of cotton or linen.
Synthetics/Easy Care
: Blouses, shirts, overalls,
etc. made of polyester or polyamide, as well as
cotton/synthetic mixes.
D) By drying level
• Sort into: iron dry, cupboard dry, etc.
Do not tumble dry:
Woollens, silk, nylon
stockings, delicate embroidery, fabrics with metallic
decorations, bulky items such as sleeping bags, etc.
Important: only use specific indicated dryer-
safe additives
and rinse items that have been
treated with stain remover thoroughly in plenty of
water before drying.
Only use specific indicated
dryer-safe plastic items
and never dry rubber or
articles contaminated with vegetable oil in the dryer.
Programme and Options:
• To select a programme, turn the programme
selector knob.
• To select an option (if available), press the
corresponding button. The button lights up,
confirming that a selection has been made. An
alarm sounds if an incorrect selection is made
(incompatible options).
• Press the button again to cancel the option.
1. Having selected the desired programme and
options, press the Start button.
If the laundry is not removed at the end of the
drying cycle, an automatic anti-crease cycle will
operate for maximum 70 min. The drum rotates
at regular intervals, preventing the laundry from
creasing.
2. On completion of the programme, set the
programme selector knob to position “0”.
The dryer indicator lamp “On” switches off.
When changing the programme during the drying
cycle, the dryer stops.
To operate the new programme, press the start
button again.
To interrupt the dryer during operation
1. Set the programme selector knob to “Airing”.
2. Press the Start button.
Wait at least 5 minutes before opening the door
to allow the dryer to cool down.
For your safety the programme stops
automatically if you open the door.
3. To restart, after door opening, close the door
and press the start button again.
Clean the lint filter at the end of every drying
cycle:
1. Open the door.
2. Pull the filter upwards.
3. Open the filter.
4. Remove lint using a soft brush or your fingertips.
5. Close the filter.
6. Push the filter firmly back into place
.
Empty the water container at the end of each
drying cycle.
1. Pull the handle to remove the water container.
2. Empty the water container.
3. Replace the water container when empty by
pushing it
completely
back in place.
When installing your dryer, always carefully
level the dryer using the adjustable feet and
check the correct levelling with a spirit level.
Clean the heat exchanger at least every 3
months. Wipe away any lint/fluff from the door
seal and interior using a damp cloth.
(Please refer to instructions for use)
To built in the dryer
Remove the work-top and replace it with the Built.in
kit UBS 10 (according to Electrical Regulations),
which can be ordered at your dealer.
If a fault occurs, before contacting our After-
Sales Service, make the following checks to try
and remedy the problem:
Drying takes too long / laundry is not dry
enough:
• Was the correct programme selected?
• Was the inserted laundry too wet (Washing
machine spin speed less than 800 rpm? When
the spinning speed is less than 800 rpm the
water container fault can occur during drying
cycle.)
• Is the lint filter dirty (filter indicator lamp on)?
• Is the heat exchanger dirty? (refer to the
Instructions for use)
• Is the ambient temperature too high?
The dryer does not operate:
(following a power failure and/or interruption
to the mains supply, always press the Start
button).
• Is the plug properly inserted into the mains
electricity socket?
• Is there a power failure?
• Has the fuse blown?
• Is the door properly closed?
• Has the programme been selected?
• Has the start delay option been selected?
• Has the
Start
button been pressed?
Lint filter or water container indicator lamp on:
• Is the lint filter clean?
• Is the water container empty?
• Is the water container correctly positioned?
• Is the heat exchanger clean?
Water droplets underneath the dryer:
• Is the heat exchanger correctly positioned?
• Has any fluff on the heat exchanger seal been
wiped away?
• Has any fluff on the door seal been wiped away?
• Has the water container been positioned correctly?.
If, after carrying out the above checks the
malfunction persists or appears again, turn the
dryer off and call our After-Sales Service (refer
to guarantee).
Please specify:
• the nature of the fault.
• the dryer type and model.
• the service code (the number after the word
Service on the adhesive rating plate) on the right
hand side when the door is open.
• your full address and phone number.
PREPARING THE LAUNDRY SELECTING A PROGRAMME AND
OPTIONS
STARTING AND COMPLETING A
PROGRAMME
CHANGING A PROGRAMME
INTERRUPTING A PROGRAMME
FILTER
WATER CONTAINER TOP
INSTALLATION STABILITY
HEAT EXCHANGER
BUILT-IN INSTALLATION
TROUBLESHOOTING GUIDE
AFTER-SALES SERVICE
-
1
-
2
dans d''autres langues
- English: LADEN AM 3793
Documents connexes
Autres documents
-
Whirlpool AWZ 865NA Program Chart
-
-
-
Bauknecht TRKK 6622 Program Chart
-
-
-
-
-
Whirlpool AZB 8200 Le manuel du propriétaire
-
Whirlpool AZB 7200 - 6TH SENSE Le manuel du propriétaire