BW Technologies microclip x3 Quick Reference Manual

Catégorie
Détecteurs de monoxyde de carbone (CO)
Taper
Quick Reference Manual

Ce manuel convient également à

1
Quick Reference Guide
1, 2, 3, and 4 Gas Detector
Limited Warranty and Limitation Liability
BW Technologies LP (BW) warrants the product to be free from defects in material and workmanship under normal use and service for a period of two years, beginning on the
date of shipment to the buyer. This warranty extends only to the sale of new and unused products to the original buyer. BW’s warranty obligation is limited, at BW’s option, to
refund of the purchase price, repair or replacement of a defective product that is returned to a BW authorized service center within the warranty period. In no event shall BW’s
liability hereunder exceed the purchase price actually paid by the buyer for the Product.
This warranty does not include:
a) fuses, disposable batteries or the routine replacement of parts due to the normal wear and tear of the product arising from use;
b) any product which in BW’s opinion, has been misused, altered, neglected or damaged, by accident or abnormal conditions of operation, handling or use;
c) any damage or defects attributable to repair of the product by any person other than an authorized dealer, or the installation of unapproved parts on the product; or
The obligations set forth in this warranty are conditional on:
a) proper storage, installation, calibration, use, maintenance and compliance with the product manual instructions and any other applicable recommendations of BW;
b) the buyer promptly notifying BW of any defect and, if required, promptly making the product available for correction. No goods shall be returned to BW until receipt by the
buyer of shipping instructions from BW; and
c) the right of BW to require that the buyer provide proof of purchase such as the original invoice, bill of sale or packing slip to establish that the product is within the
warranty period.
THE BUYER AGREES THAT THIS WARRANTY IS THE BUYERS SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. BW SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR BASED ON CONTRACT,
TORT OR RELIANCE OR ANY OTHER THEORY.
Since some countries or states do not allow limitation of the term of an implied warranty, or exclusion or limitation of incidental or consequential damages, the limitations and
exclusions of this warranty may not apply to every buyer. If any provision of this warranty is held invalid or unenforceable by a court of competent jurisdiction, such holding will
not affect the validity or enforceability of any other provision.
Contacting BW Technologies by Honeywell
Email us at: [email protected]
Visit BW Technologies by Honeywell’s website at: www.honeywellanalytics.com
USA: 1-888-749-8878 Canada: 1-800-663-4164
Europe: 00800-333-22244 Other countries: +1-403-248-9226
The license for manufacturing measuring
instrument of the People’s Republic of China.
CMC No
Hu Zhi 00000324
CPA No
2015C206-31
Company Standard No Q31/0114000029C002-2015
GasAlertMicroClip
Introduction
1
GasAlertMicroClip
Introduction
The Quick Reference Guide provides basic information for the
GasAlertMicroClip XT, XL and X3. For complete operating
instructions, refer to the GasAlertMicroClip User Manual from
www.honeywellanalytics.com. The GasAlertMicroClip (“the
detector”) warns of hazardous gas at levels above user-defined
alarm setpoints. The detector is a personal safety device. It is
your responsibility to respond properly to the alarm.
Note
The detector is shipped with English as the default
displayed language. Additional languages provided are
Portuguese, Spanish, German, and French. The screens
for the additional languages are displayed on the detector
and in the corresponding operator’s manuals.
What’s In a Box
Detector
Calibration Cap
Battery Charging Adapter
Documentation Kit
Certificate (GasAlertMicroClip XT)
Zeroing the Sensors
To zero the sensors, refer to steps #1-3 in Calibration on page 7.
ec Warning
This instrument contains a lithium polymer battery.
Dispose of lithium cells immediately. Do not disassemble
and do not dispose of in fire. Do not mix with the solid
waste stream. Spent batteries should be disposed of by a
qualified recycler or hazardous materials handler.
ec Avertissement
Cet appareil contient une batterie au lithium polymère.
Mettez immédiatement au rebut les piles au lithium
usagées. Veillez à ne jamais les démonter ou les jeter au
feu. Ne les mélangez pas aux autres déchets solides. Les
piles usagées doivent être éliminées par un centre de
recyclage agréé ou par un centre de traitement de matières
dangereuses.
GasAlertMicroClip
Quick Reference Guide
2
XT, XL and X3 Safety Information - Read First
Use the detector only as specified in this manual and the
reference guide, otherwise the protection provided by the
detector may be impaired. Read the following cautions before
using the detector.
a
Cautions
Warning: Substitution of components may impair
Intrinsic Safety.
Caution: For safety reasons, this equipment must be
operated and serviced by qualified personnel only.
Read and understand the user manual completely
before operating or servicing.
Charge the detector before first time use. BW
recommends the detector be charged after every
workday.
Before using the detector, refer to
Sensor Poisons and
Contaminants.
Calibrate the detector before first-time use and then on
a regular schedule, depending on use and sensor
exposure to poisons and contaminants. BW
recommends calibrating at least once every 180 days
(6 months).
The combustible sensor is factory calibrated to 50%
LEL methane. If monitoring a different combustible gas
in the %LEL range, calibrate the sensor using the
appropriate gas.
Only the combustible gas detection portion of this
instrument has been assessed for performance by
CSA International.
Calibrate only in a safe area that is free of hazardous
gas and in an atmosphere of 20.9% oxygen.
It is recommended that the combustible sensor be
checked with a known concentration of calibration gas
after any exposure to contaminants/poisons such as,
sulfur compounds, silicon vapors, halogenated
compounds, etc.
BW recommends to bump test the sensors before each
day’s use to confirm their ability to respond to gas by
exposing the detector to a gas concentration that
exceeds the alarm setpoints. Manually verify that the
audible and visual alarms are activated. Calibrate if the
readings are not within the specified limits.
Caution: High off-scale readings may indicate an
explosive concentration.
Any rapid up scaling reading followed by a declining or
erratic reading may indicate a gas concentration
beyond the upper scale limit, which can be hazardous.
Extended exposure of the GasAlertMicroClip to certain
concentrations of combustible gases and air may stress
a detector element that can seriously affect its
GasAlertMicroClip
XT, XL et X3 Informations de sécurité – À lire au préalable
3
performance. If an alarm occurs due to a high
concentration of combustible gases, calibrate the
detector. If necessary, replace the sensor.
Protect the combustible sensor from exposure to lead
compounds, silicones, and chlorinated hydrocarbons.
Sensor exposure to certain organic vapors (such as
leaded gasoline and halogenated hydrocarbons) may
temporarily inhibit sensor performance. After exposure,
a bump test or calibration is recommended.
For use only in potentially explosive atmospheres
where oxygen concentrations do not exceed 20.9%
(v/v).
Products may contain materials that are regulated for
transportation under domestic and international
dangerous goods regulations. Return product in
compliance with appropriate dangerous goods
regulations. Contact freight carrier for further
instructions.
XT, XL et X3 Informations de sécurité –
À lire au préalable
Respectez rigoureusement les instructions d'utilisation figurant
dans ce manuel ainsi que dans le guide technique sous peine
de compromettre la protection offerte par le détecteur. Lisez les
mises en garde suivantes avant d’utiliser le détecteur.
a
Mises en garde
Avertissement : Le remplacement d'un composant de
l'appareil peut compromettre la sécurité intrinsèque du
détecteur.Mise en garde : Pour des raisons de sécurité,
cet appareil doit être utilisé et entretenu par du
personnel qualifié uniquement.
Lisez attentivement le manuel avant d’utiliser l’appareil
ou d'en assurer l'entretien et assurez-vous d'en avoir
bien compris les instructions.
Chargez le détecteur avant sa première utilisation. BW
recommande de recharger le détecteur après chaque
journée d’utilisation.
Avant toute utilisation du détecteur, reportez-vous à la
section .
Étalonnez le détecteur avant sa première utilisation,
puis de manière régulière, en fonction de l’utilisation et
de l’exposition du capteur aux poisons et autres
contaminants. BW recommande d'effectuer un
étalonnage au moins une fois tous les 180 jours
(6 mois).
Le capteur de gaz combustibles est étalonné en usine
au méthane, à une concentration de 50 % de la LIE. Si le
contrôle porte sur un autre gaz combustible dans la
plage de % LIE, étalonnez le capteur en utilisant le gaz
approprié.
GasAlertMicroClip
Quick Reference Guide
4
Sur cet appareil, seule la détection de gaz combustibles
a fait l’objet d’une évaluation des performances par
CSA International.
Veillez à effectuer l'étalonnage dans une zone sûre,
exempte de gaz dangereux, et dans une atmosphère
contenant 20,9 % d'oxygène.
Si le capteur de gaz combustibles a été exposé à des
contaminants/poisons (composés de soufre, vapeurs de
silicium, produits halogénés, etc.), il est conseillé de
vérifier son bon fonctionnement en le mettant en
présence d'une concentration connue d'un gaz.
Avant chaque utilisation quotidienne, BW recommande
d’effectuer un test fonctionnel des capteurs afin de
vérifier qu’ils réagissent bien aux gaz présents, en
exposant le détecteur à une concentration de gaz
supérieure aux seuils d’alarme. Vérifiez manuellement
que les alarmes sonore et visuelle sont activées.
Étalonnez l’appareil si les relevés ne sont pas
conformes aux limites spécifiées.
Mise en garde : Des relevés élevés hors échelle peuvent
indiquer la présence d’une concentration explosive.
Toute mesure en rapide augmentation suivie d’une
diminution ou d’une mesure fantaisiste peut indiquer
une concentration de gaz au-delà de la limite d’échelle
supérieure, risquant donc d’être dangereuse.
Une exposition prolongée du GasAlertMicroClip XT à
certaines concentrations de gaz combustibles et dans
certaines atmosphères peut nuire à l'élément de
détection et altérer gravement ses performances.
Étalonnez le détecteur après toute exposition à des
concentrations élevées de gaz combustibles ayant
déclenché son alarme. Si nécessaire, remplacez le
capteur.
Protégez le capteur de gaz combustibles contre toute
exposition aux composés de plomb, aux silicones et
aux hydrocarbures chlorés.
L'exposition du capteur à certaines vapeurs organiques
(comme l'essence au plomb ou les hydrocarbures
halogénés) peut altérer temporairement son bon
fonctionnement. Il est recommandé de procéder à un
test fonctionnel ou à un étalonnage après toute
exposition.
Cet appareil est destiné uniquement à une utilisation
dans des atmosphères potentiellement explosives,
dans lesquelles la concentration d’oxygène ne dépasse
pas 20,9 % (v/v).
Les produits peuvent contenir des matériaux qui sont
réglementés pour le transport en vertu des règlements
nationaux et internationaux de marchandises
dangereuses. Retourner le produit conformément à la
réglementation sur les marchandises dangereuses
appropriées. Contactez transporteur de fret pour plus
d'instructions
GasAlertMicroClip
Parts of the GasAlertMicroClip
5
Parts of the GasAlertMicroClip
8
6
9
4
5
3
7
10
11
2
2
1
2
Item Description
1 IntelliFlash
2 Visual alarm indicators (LEDs)
3 Alligator clip
4 Charging connector / IR interface
5 Pushbutton
6 Carbon monoxide (CO) sensor
7 Hydrogen sulfide (H
2
S) sensor
8 Oxygen (O
2
) sensor
9 Combustible (LEL) sensor
10 Audible alarm
11 Liquid crystal display (LCD)
GasAlertMicroClip
Quick Reference Guide
6
Display Elements
1
8
7
6
5
4
3
2
Item Description
1 Alarm condition
2 Automatically zero sensor
3 Numeric value
4 Stealth mode
5 Battery life indicator
6 Gas identifier bars
7 Gas cylinder
8 Automatically span sensor
GasAlertMicroClip
Pushbutton
7
Pushbutton
To activate the detector, press C.
To deactivate the detector, press and hold C until the OFF
countdown is complete and the LCD deactivates.
To view the TWA, STEL, and MAX (maximum) readings, press
C twice. To clear the TWA, STEL, and MAX readings, press
C when the LCD displays RESET.
To initiate calibration, deactivate the detector. Press and hold
C while the detector performs the OFF countdown. Continue
holding C while the LCD briefly deactivates and then begins
the CAL countdown. Release C when the CAL countdown is
complete.
To activate the backlight while in normal operation, press C.
To acknowledge latched alarms, press C.
To acknowledge a low alarm and disable the audible alarm,
press C (if the Low Alarm Acknowledge option is enabled).
Sensor Poisons and Contaminants
Several cleaners, solvents, and lubricants can contaminate and
cause permanent damage to sensors. Before using cleaners,
solvents, and lubricants in close proximity to the detector
sensors, read the following caution and table.
a
Caution
Use only the following BW Technologies by Honeywell
recommended products and procedures:
Use water based cleaners.
Use non-alcohol based cleaners.
Clean the exterior with a soft, damp cloth.
Do not use soaps, polishes, or solvents.
Below are common products to avoid using around sensors.
Cleaners and Lubricants
Brake cleaners
Lubricants
Rust inhibitors
Window and glass cleaners
Dishsoaps
Citrus based cleaners
GasAlertMicroClip
Quick Reference Guide
8
Alcohol based cleaners
Hand sanitizers
Anionic detergents
Methanol (fuels and antifreezes)
Silicones
Silicone cleaners and protectants
Silicone based adhesives, sealants, and gels
Hand/body and medicinal creams containing silicone
Tissues containing silicone
Mold releasing agents
Polishes
Aerosols
Bug repellents and sprays
Lubricants
Rust inhibitors
Window cleaners
GasAlertMicroClip
Calibration
9
Calibration
Procedure Display Procedure Display
a
Caution
Calibrate only in a safe area that is free of
hazardous gas in an atmosphere of 20.9%
oxygen.
1. Press and hold
C as the detector
performs the OFF countdown. Continue
holding C when the LCD briefly
deactivates.
4. When is displayed and
flashes, connect the gas cylinder (refer to
page
10) and apply gas at a flow rate of
250 to 500 ml/min.
After a sufficient amount of gas has been
detected (approximately 30 seconds), the
detector beeps, is displayed, and
flashes while the detector
completes the calibration.
2. The LCD then activates again and
performs the
CAL countdown. Continue
holding C until the countdown is complete
to enter calibration.
5. The LCD displays CAL DUE. Next, a
screen displays showing the number of
days remaining before calibration is due
for each sensor. The LCD then displays
the earliest calibration due date, as some
sensors require more frequent
calibrations.
3. flashes while the detector
zeroes all of the sensors and calibrates the
oxygen sensor. If a sensor fails to auto
zero, it cannot be calibrated. When auto
zero is complete, the LCD displays APPLY
GAS.
Note: Only use the calibration cap during the calibration
span process and for bump tests.
Wind currents may cause false readings and poor calibrations.
Do not calibrate the detector during or immediately after
charging is complete.
GasAlertMicroClip
Quick Reference Guide
10
Attach the Gas Cylinder to the Detector
GasAlertMicroClip
Bump Test
11
Bump Test
Use a premium-grade gas. Use gases approved by the National
Institute of Standards and Technology. Do not use a gas
cylinder that is past its expiration date.
Note: To perform an automated bump test, refer to the
MicroDock II User Manual.
1. Connect the calibration hose to the 0.5 l/min regulator
on the gas cylinder. For use with the MicroDock II,
use a demand flow regulator.
Note: Cylinders that are used with a demand flow
regulator must meet the following maximum inlet
pressure specifications:
- Disposable cylinders 0-1000 psig/70 bar
- Refillable cylinders 0-3000 psig/207 bar
2. Connect the calibration hose to the calibration cap.
3. Attach the calibration cap to the detector.
4. Apply gas. Verify the visual and audible alarms
activate.
5. Close the regulator and remove the calibration cap
from the detector.
Note: The detector will temporarily remain in alarm
until the gas clears from the sensors.
6. Disconnect the hose from the calibration cap and the
regulator.
Note: Only use the calibration cap during calibration and bump
test.
GasAlertMicroClip
Quick Reference Guide
12
Alarms
If Stealth mode is enabled, the audible and visual alarms are
disabled. Only the vibrator alarm activates..
Alarm Display Alarm Display
Low Alarm
Slow siren
Slow alternating flash
L and gas bar flash
Vibrator alarm activates
TWA Alarm
Slow siren
Slow alternating flash
L and gas bar flash
Vibrator alarm activates
High Alarm
Fast siren
Fast alternating flash
L and gas bar flash
Vibrator alarm activates
STEL Alarm
Fast siren
Fast alternating flash
L and gas bar flash
Vibrator alarm activates
Multi-Gas Alarm
Alternating low and high alarm siren and
flash
L and gas bars flash
Vibrator alarm activates
Over Limit (OL) Alarm
Fast siren and alternating flash
L and gas bar flash
Vibrator alarm activates
OL displays
GasAlertMicroClip
Alarms
13
Alarm Display Alarm Display
Sensor Alarm
During startup Error [sensor name]
displays
During normal operation Err displays
Confidence Beep and IntelliFlash
One beep and flash every second
Note: Confidence Beep and
IntelliFlash automatically
deactivate during low battery
alarm, self-test fail, calibration fail,
bump test fail, or an alarm event.
Low Battery Alarm
Sequence of 10 rapid sirens and
alternating flashes with 7 seconds of
silence in between (continues for
15 minutes)
and
L
flash, LOW BAT
displays, and the vibrator alarm activates
After 15 minutes of the Low Battery
alarm, the Automatic Shutdown Alarm
sequence begins
OFF displays before deactivating
Automatic Shutdown Alarm
Sequence of 10 rapid sirens and
alternating flashes with 1 second of
silence in between (sequence reactivates
seven times)
LOW BAT and
L display, and
vibrator alarm activates
OFF displays before deactivating
Note: Alarms can be set to latching or non-latching. To enable/disable
latching, select/deselect Latching Alarms in Fleet Manager II. Local
regulations may require a latching alarm.
If Low Alarm Acknowledge is enabled and a low alarm occurs, press
C to disable the audible alarm. The visual and vibrator alarms remain
activated. If the alarm escalates to a high, STEL, or TWA alarm, the
audible alarm reactivates.
GasAlertMicroClip
Quick Reference Guide
14
User Options Menu
To modify the user options, connect the detector to the IR Link
adapter and open Fleet Manager II. Refer to the Fleet Manager
II Operator’s Manual for complete instructions.
1. Sensors (H
2
S, CO, LEL, and O
2
)
Sensor Disabled: Disables the sensor.
Calibration Gas (ppm) / (%LEL) / (%O
2
): Defines the
calibration gas concentration for each sensor.
Calibration Interval (days): Defines how often a
calibration should be performed.
Bump Interval (days): Defines how often a bump test
should be performed.
Low Alarm (ppm) / (%LEL) / (%O
2
): Defines the low
alarm setpoint.
High Alarm (ppm) / (%LEL) / (%O
2
): Defines the high
alarm setpoint.
TWA Alarm (ppm): Defines the time-weighted average
(TWA) alarm setpoint. H
2
S and CO sensors only.
STEL Alarm (ppm): Defines the short-term exposure limit
(STEL) alarm setpoint. H
2
S and CO sensors only.
STEL Interval (minutes): Defines the short-term
exposure limit (5-15 minutes). H
2
S and CO sensors only.
Auto-Zero Startup: When enabled, the detector
automatically zeros the H
2
S, CO, and LEL sensors during
the startup self-test.
LEL By Volume CH4: When enabled, the LEL reading is
displayed as %vol., assuming a methane environment.
O
2
Auto-Calibration on Startup: When enabled, the O
2
sensor is automatically calibrated during startup.
2. User Options
Confidence Beep: When enabled, the detector beeps
once every second to verify the battery has sufficient
power to detect hazardous gas and emit an alarm.
Detector is shipped with Confidence Beep disabled.
Latching Alarms: When enabled, the audible, visual, and
vibrator alarms persist during a high or low alarm until the
gas concentration is below the low alarm setpoint and has
been acknowledged by pressing C.
Safe Mode: When enabled, SAFE continuously displays
on the LCD when all gas concentrations are normal or
below the alarm setpoints.
Stealth Mode: When enabled, the audible alarm, LEDs
and backlight are disabled. displays on the LCD.
Low Alarm Acknowledge: When enabled, the audible
alarm can be disabled during a low alarm. The vibrator,
LEDs, and LCD remain enabled. For H
2
S, CO, and LEL
sensors only.
Datalog Interval (seconds): Enter a value
(1-120 seconds).
Force Calibration When Overdue: When enabled, the
detector automatically enters calibration during startup for
overdue sensors. If the sensors are not calibrated
immediately, the detector will deactivate.
GasAlertMicroClip
Charging the Rechargeable Battery
15
Cal Lock: When enabled, the sensors can only be
calibrated using an IR device (IR Link with Fleet Manager
II or the MicroDock II base station).
Force Bump When Overdue: When enabled, a bump test
is required if the sensor has exceeded its bump test
interval. If a successful bump test is not performed, the
detector will deactivate.
IntelliFlash: When enabled, the green LED flashes to
provide continuous visual confirmation that the detector is
operating correctly.
IntelliFlash automatically deactivates during a low
battery alarm, a self-test fail, a calibration fail, a bump
test fail, or during an alarm event. To define how often
IntelliFlash occurs (1-60 seconds), refer to
Confidence
Beep and IntelliFlash Interval. Default setting is
1 second. Detector is shipped with IntelliFlash enabled.
Confidence Beep and IntelliFlash Interval: Enter a
value (1-60 seconds) to define how often IntelliFlash
occurs and the detector beeps. Intelliflash and/or
Confidence Beep must be enabled in order to define
Confidence Beep and IntelliFlash Interval.
Language: Select the language to display on the LCD:
English, Français (French), Deutsch (German), Español
(Spanish), or Português (Portuguese).
Charging the Rechargeable Battery
a Warning
Only the manufacturer can replace the rechargeable
battery. Failure to adhere to this caution can lead to fire
and/or explosion.
Charge only in a safe area that is free of hazardous gas
and within temperatures of 32°F to 113°F (0°C to 45°C).
The charging adapter is specific to your region. Use of the
charging adapter outside your region will damage the
charger and the detector.
Do not calibrate during or immediately after charging.
1. Deactivate the detector. Insert the charging adapter
plug into an AC outlet.
GasAlertMicroClip
Quick Reference Guide
16
2. Connect the charging adapter to the detector IR
interface.
3. Charge the battery.
4. Charge the battery after each workday.
Maintenance
To maintain the detector in good operating condition, perform
the following basic maintenance as required.
Calibrate, bump test, and inspect the detector on a regular
schedule.
Maintain an operations log of all maintenance, bump tests,
calibrations, and alarm events.
Clean the exterior with a soft damp cloth. Do not use
solvents, soaps, or polishes.
Replacing a Sensor or Sensor Filter
a Warning
To avoid personal injury, use only sensors specifically
designed for the detector.
Use proper ESD handling practices.
a
Caution
Ensure hands are clean or wear gloves before handling
components.
To replace a sensor or sensor filter, refer to the following
illustration, table, and procedures.
1 Detector
2 IR and charger interface
3 Charging adapter
4 Charging Cable
GasAlertMicroClip
Maintenance
17
Removing the back shell
1. Deactivate the detector. On a clean surface, place the
detector face down.
2. Remove the six machine screws from the rear shell.
Remove the back cover by lifting the top and the
bottom upwards simultaneously to prevent damaging
the charging pins.
1
11
10
3
2
4
6
5
8
9
7
Item Description Item Description Item Description
1 Front shell 5 Rear shell 9 H
2
S sensor
2 LEL sensor 6 Machine screws (6) 10 O
2
sensor
3 PCB 7 Sealing rib 11 Sensor filter
4 PCB screws (2) 8 CO sensor
GasAlertMicroClip
Quick Reference Guide
18
Replacing the sensor filter
1. Note the placement of the PCB to ensure it is
replaced correctly. Remove the two screws on the
PCB. Remove the PCB carefully.
a
Caution
Ensure no damage occurs to the battery.
2. Remove the old sensor filter. It may be stuck to the
sensors.
3. Pull the liner tab, if present, to remove the liner from
the sensor filter. Do not fold the sensor filter.
4. Verify that the black gasket is facing the front shell
and the large diameter circle on the gasket is aligned
with the large circle on the front shell.
5. Place the gasket as shown, and then use your fingers
to apply even pressure to the entire gasket.
6. To reassemble the detector, refer to
Reassembling
the detector.
Liner tab
Large diameter circle
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

BW Technologies microclip x3 Quick Reference Manual

Catégorie
Détecteurs de monoxyde de carbone (CO)
Taper
Quick Reference Manual
Ce manuel convient également à

dans d''autres langues