LG MA12AH1-M Le manuel du propriétaire

Marque: LG

Modèle: MA12AH1-M

Catégorie: Climatiseurs split-system

Taper: Le manuel du propriétaire

www.lg.com

OWNER’S MANUAL

AIR CONDITIONER

Please read this manual carefully before operating

your set and retain it for future reference.

TYPE : Multi

The equipment complies with requirements of the Technical

Regulation, in terms of restrictions for the use of certain dangerous

substances in electrical and electronic equipment.

P/NO : MFL37562502

ENGLISH ITALIANO

ESPAÑOL

FRANÇAIS DEUTSCH

2 Multi Air Conditioner

Multi Air Conditioner Owner’s Manual

TABLE OF CONTENTS

FOR YOUR RECORDS

Write the model and serial numbers here:

Model #

Serial #

You can find them on a label on the side of each unit.

Dealer's Name

Date Purchased

■ Staple your receipt to this page in the event you need

it to prove date of purchase or for warranty issues.

READ THIS MANUAL

Inside you will find many helpful hints on how to use

and maintain your air conditioner properly. Just a little

preventive care on your part can save you a great deal

of time and money over the life of your air conditioner.

You'll find many answers to common problems in the

chart of troubleshooting tips. If you review our chart of

Troubleshooting Tips first, you may not need to call

for service at all.

PRECAUTION

• Contact the authorized service technician for

repair or maintenance of this unit.

• Contact the installer for installation of this unit.

• The air conditioner is not intended for use by

young children or invalids without supervision.

• Young children should be supervised to ensure

that they do not play with the air conditioner.

• When the power cord is to be replaced,

replacement work shall be performed by

authorized personnel only using only genuine

replacement parts.

Safety Precautions...................................3

Electrical Safety .......................................6

Temporary Use of an Adapter ...............6

Temporary Use of an Extension Cord ...6

Symbols used in this Manual.................6

Operating Instructions ............................7

How to insert the Batteries ....................7

Wireless Remote Controller

Maintenance..........................................7

Operating Method..................................7

Operation Indication Lamps ..................8

Wireless Remote Controller...................9

Operation Mode...................................10

Healthy Dehumidification Operation....11

Air Circulation Operation .....................11

Auto Operation ....................................11

Jet Cool/Heat Operation......................12

Auto Clean Operation..........................12

NEO PLASMA Purification

Operation (Optional)............................12

Energy-Saving Cooling Mode

(Optional).............................................13

Display Luminosity (Optional)..............13

Forced operation .................................13

Setting the Current Time .....................14

Timer Setting .......................................14

To cancel the timer setting ..................14

Sleep Mode .........................................14

Vertical / Horizontal Airflow Direction

Control (Optional) ................................15

Auto Restart Function..........................15

Maintenance and Service ......................16

Artcool Mirror Type..............................16

Artcool Type ........................................17

How to replace picture & photograph

(Art Cool Type2) ..................................18

When the air conditioner is not going

to be used for a long time....................19

Operation Tips.....................................19

Troubleshooting...................................20

Owner's Manual 3

Safety Precautions

ENGLISH

Safety Precautions

To prevent injury to the user or other people and property damage, the following instructions must be followed.

■ Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified by

the following indications.

■ Meanings of symbols used in this manual are as shown below.

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage.

Be sure not to do.

Be sure to follow the instruction.

Always use a power plug and socket with

a ground terminal.

• There is a risk of electric shock.

Do not use a defective or underrated

circuit breaker. Use the correctly rated

breaker and fuse.

• There is risk of fire or electric shock .

Do not use a multi consent. Always use

this appliance on a dedicated cicuit and

breaker.

• Otherwise it can cause electric shock or fire.

For electrical work, contact the dealer, seller,

a qualified electrician, or an Authorized

Service Center. Do not disassemble or repair

the product by yourself.

• There is risk of fire or electric shock.

Always ground the product as per the

wiring diagram. Do not connect the

ground wire to gas or water pipes

lightening rod or telephone ground wire.

• There is risk of fire or electric shock.

Install the panel and the cover of control

box securely.

• There is risk of fire or electric shock due to

dust , water etc.

Use the correctly rated breaker or fuse.

• There is risk of fire or electric shock.

Do not modify or extend the power cable.

If the power cable or cord has scrathes or

skin peeled off or deteriorated then it

must be replaced.

• There is risk of fire or electric shock.

For installation, removal or reinstall ,

always contact the dealer or an

Authorized Service Center.

• There is risk of fire, electric shock, explosion,

or injury.

Do not install the product on a defective

installation stand. Be sure that the

installation area does not deteriorate with

age.

• It may cause product to fall.

Never install the outdoor unit on a

moving base or a place from where it

can fall down.

• The falling outdoor unit can cause damage or

injury or even death of a person.

When the product is soaked (flooded or

submerged) in water , contact an

Authorized Service Center for repair

before using it again.

• There is risk of fire or eletric shock.

In outdoor unit the step-up capacitor

supplies high voltage electricity to the

electrical components. Be sure to

discharge the capacitor completely

before conducting the repair work.

• An charged capacitor can cause electrical

shock.

When installing the unit, use the

installation kit provided with the product.

• Otherwise the unit may fall and cause severe

injury.

Be sure to use only those parts which

are listed in the svc parts list. Never

attempt to modify the equipment.

• The use of inappropriate parts can cause an

electrical shock, excessive heat generation or

fire.

4 Multi Air Conditioner

Safety Precautions

Indoor/outdoor wiring connections must

be secured tightly and the cable should

be routed properly so that there is no

force pulling the cable from the

connection terminals.

• Improper or loose connections can cause

heat generation or fire.

Safely dispose off the packing materials.

Like screws, nails, batteries, broken

things etc after installation or svc and

then tear away and thraw away the plastic

packaging bags.

• Children may play with them and cause

injury.

Make sure to check that the power cable

plug is not dirty, loose or broken and

then only insert the plug completely.

• Dirty, loose or broken power plug can

cause electric shock or fire.

Be sure to check the refrigerant to the

used. Please read the label on the product.

• Incorrect refrigerant used can prevent the

normal operation of the unit.

Don't use a power cord, a plug or a loose

socket which is damaged.

• Otherwise it may cause a fire or electrical

shock.

Do not touch , operate, or repair the

product with wet hands. Hold the plug by

hand when taking out

• There is risk of electric shock or fire.

Do not place a heater or other heating

appliances near the power cable.

• There is risk of fire and electric shock.

Do not allow water to run into electric

parts. Install the unit away from water

sources.

• There is risk of fire, failure of the product, or

electric shock.

Do not store or use or even allow

flammable gas or combustibles near the

product.

• There is risk of fire.

Do not use the product in a tightly closed

space for a long time. Perform ventilation

regularly.

• Oxygen deficiency could occur and hence

harm your health.

Do not open the front grille of the product

during operation. (Do not touch the

electrostatic filter, if the unit is so equipped.)

• There is risk of physical injury, electric shock,

or product failure.

If strange sounds, smell or smoke comes

from product.Immediately turn the breaker

off or disconnect the power supply cable.

• There is risk of electric shock or fire.

Ventilate the product room from time to

time when operating it together with a

stove, or heating element etc.

• Oxygen deficiency can occur and hence harm

your health.

Turn the main power off and unplug the

unit when cleaning or repairing the

product.

• There is risk of electric shock.

When the product is not to be used for a

long time, disconnect the power supply

plug or turn off the breaker.

• There is risk of product damage or failure, or

unintended operation.

Take care to ensure that nobody

especially kids could step on or fall onto

the outdoor unit.

• This could result in personal injury and

product damage.

Take care to ensure that power cable

could not be pulled out or damaged

during operation.

• There is risk of fire or electric shock.

Do not place ANYTHING on the power

cable.

• There is risk of fire or electric shock.

Do not plug or unplug the power supply plug to turn the unit

ON/OFF .

• There is risk of fire or electric shock.

When flammable gas leaks, turn off the gas and open a window

for ventilation before turn the product on.

• Do not use the telephone or turn switches on or off. There is risk of

explosion or fire.

Two or more people must lift and

transport the product.

• Avoid personal injury.

Do not install the product where it will be

exposed to sea wind (salt spray) directly.

• It may cause corrosion on the product.

Install the drain hose to ensure that the

condensed water is drained away properly.

• A bad connection may cause water leakage.

Keep level even when installing the

product.

• To avoid vibration or noise.

Do not install the product where the noise

or hot air from the outdoor unit could

damage or disturb the neighborhoods.

• It may cause a problem for your neighbors

and hence dispute.

Always check for gas (refrigerant)

leakage after installation or repair of

product.

• Low refrigerant levels may cause failure of

product.

Owner's Manual 5

Safety Precautions

ENGLISH

Do not use the product for special purposes,

such as preserving foods, works of art, etc. It

is a consumer air conditioner, not a precision

refrigeration system.

• There is risk of damage or loss of property.

Do not block the inlet or outlet of air flow.

• It may cause product failure.

Use a soft cloth to clean. Do not use

harsh detergents, solvents or splashing

water etc .

• There is risk of fire, electric shock, or damage

to the plastic parts of the product.

Do not touch the metal parts of the

product when removing the air filter.

• There is risk of personal injury.

Do not step on or put anyting on the

product. (outdoor units)

• There is risk of personal injury and failure of

product.

Always insert the filter securely after

cleaning. Clean the filter every two weeks

or more often if necessary.

• A dirty filter reduces the efficiency.

Do not insert hands or other objects

through the air inlet or outlet while the

product is operating.

• There are sharp and moving parts that could

cause personal injury.

Be cautious when unpacking and

installing the product.

• Sharp edges could cause injury.

If the refrigerant gas leaks during the

repair, do not touch the leakaing

refrigerant gas.

• The refrigernat gas can cause frostbite (cold

burn)

Do not tilt the unit when removing or

uninstalling it.

• The condensed water inside can spill .

Do not mix air or gas other than the

specified refrigerant used in the system .

• If air enters the refrigerant system, an

excessively high pressure results, causing

equipment damage or injury.

If the refrigerant gas leaks during the

installation, ventilate the area immediately.

• Otherwise it can be harmfull for your health.

Dismantling the unit, treatment of the

refrigerant oil and eventual parts should

be done in accordance with local and

national standards.

Replace the all batteries in the remote

control with new ones of the same type.

Do not mix old and new batteries or

different types of batteries.

• There is risk of fire or product failure.

Do not recharge or disassemble the

batteries. Do not dispose off batteries in

a fire.

• They may burn or explode.

If the liquid from the batteries gets onto

your skin or clothes, wash it well with

clean water. Do not use the remote if the

batteries have leaked.

• The chemicals in batteries could cause burns

or other health hazards.

If you eat the liquid from the batteries,

brush your teeth and see doctor. Do not

use the remote if the batteries have

leaked.

• The chemicals in batteries could cause

burns or other health hazards.

Do not let the air conditioner run for a

long time when the humidity is very high

and a door or a window is left open.

• Moisture may condense and wet or damage

furniture.

Do not expose your skin or kids or

plants to the cool or hot air draft.

• This could harm to your health.

Do not drink the water drained from the

product.

• It is not sanitary and could cause serious

health issues.

Use a firm stool or ladder when cleaning,

maintaining or repairing the product at an height.

• Be careful and avoid personal injury.

6 Multi Air Conditioner

Electrical Safety

• This appliance must be properly grounded.

To minimize the risk of electric shock, you must alway plug into a grounded oulet.

• Do not cut or remove the grounding prong from the power plug.

• Attaching the adapter ground terminal to the wall receptacle cover screw does not ground the appliance

unless the cover screw is metal and not insulated, and the wall receptacle is grounded through the

house wiring.

• If you have any doubt whether the air conditioner is properly grounded, have the wall receptacle and

circuit checked by a qualified electrician.

We strongly discourage the use of an adapter due to potential safety hazards. For temporary connections,

use only a genuine adapter, available from most local hardware stores. Ensure that the large slot in the

adapter is aligned with the large slot in the receptacle for a proper polarity connection.

To disconnect the power cord from the adapter, use one hand on each to avoid damaging the ground

terminal. Avoid frequently unplugging the power cord as this can lead to eventual ground terminal damage.

• Never use the appliance with a broken adapter.

We strongly discourage the use of an extension cord due to potential safety hazards. For temporary

situations, use only CSA certified and UL listed 3-wire grounded extension cords, rated 15 A, 125 V.

Temporary Use of an Adapter

Temporary Use of an Extension Cord

This symbol alerts you to the risk of electric shock.

This symbol alerts you to hazards that may cause harm to the

air conditioner.

This symbol indicates special notes.

NOTE

Symbols used in this Manual

This appliance should be installed in accordance with national wiring regulations. This guide acts as a

guide to help to explain product features.

The Power cord connected to the unit should be selected according to the following specifications.

ENGLISH

Owner's Manual 7

Operating Instructions

1. Choose a suitable place where its safe & easy to reach.

2. Fix the holder to wall etc with the supplied screws firmly.

3. Slide the remote controller inside the holder.

1. Remote controller should never be exposed to direct sunlight.

2. Signal transmitter & receiver should always be clean for proper communication. Use a soft cloth to

clean them.

3. In case some other appliances also get operated with remote control, change their position or consult

your serviceman.

NOTE

1. The signal receiver is inside the unit.

Aim the remote controller towards the unit to operate it. There should not be any blockage in between.

Artcool Mirror Type Artcool Type

Operating Instructions

How to insert the Batteries

Wireless Remote Controller Maintenance

1. Remove the battery cover by pulling it according to the arrow

direction.

2. Insert new batteries making sure that the (+) and (-) of battery are

installed correctly.

3. Reattach the cover by sliding it back into position.

1. Always use/replace both batteries of same type.

2. If the system is not to be used for a long time, remove the

batteries to save their working life.

3. If the display screen of remote controller starts, fading replace

both of the batteries.

NOTE

Operating Method

8 Multi Air Conditioner

Operating Instructions

On/Off

: Lights up during the system operation, error code and auto restart setting.

Sleep mode

Energy-Saving

Cooling Mode

: Lights up during sleep mode auto operation.

: Lights up during Energy-Saving Cooling Mode Operation.

Plasma : The function illustrates its dynamic mode by using a multiple lighting system.

Timer

: Lights up during timer operation or sleep mode auto operation.

Defrost mode

Power Display : Indicates the setting temperature and operation mode.

: Lights up during defrost mode or *hot start operation (Heat pump model only)

: Lights up during outdoor unit operation. (Cooling model only)

Outdoor unit

operation

OUT

DOOR

Artcool Mirror Type

Display panel LCD indicators

Artcool Type

Display panel LED indicators

Signal receiver

Front panel

Air discharge

ON/OFF button

Plasma filter

Air inlet

Air filter

Signal receiver

Front Panel

Air Discharge

Air Filter

Plasma Filter

On/Off : Lights up during the system operation, error code and auto restart setting.

* Hot start operation: Stops the indoor fan in heating operation for minutes to prevent cold air from blowing out

from unit.

* In defrost mode unit stops heating operation for few minutes to remove formation of ice on the heat

exchanger coils to maintain the efficiency.

Operation Indication Lamps

Owner's Manual 9

ENGLISH

Cooling Operation

Auto Operation

Healthy Dehumidification Operation

Heating Operation

Air Circulation

Signal transmitter

•

Cooling Model( ), Heat Pump Model( )

Operation Mode

Operating Instructions

The controls will look like the following.

Wireless Remote Controller

1. ON/OFF BUTTON

Used to turn off/on the unit.

2. OPERATION MODE SELECTION BUTTON

Used to select the operation mode.

3. ROOM TEMPERATURE SETTING BUTTONS

Used to select the room temperature.

4. INDOOR FAN SPEED SELECTOR BUTTON

Used to select fan speed in four steps

low, medium, high and CHAOS.

5. JET COOL BUTTON

Used to start or stop the speed cooling.

(It operates fan in super high speed in cooling mode)

6. CHAOS SWING BUTTON

Used to stop or start louver movement and set the

desired up/down airflow direction.

7. TIMER AND TIME SETTING BUTTON

Used to set the time of starting and stopping

operation.

8. TIME SETTING BUTTONS

Used to adjust the time.

9. TIMER SET / CLEAR BUTTON

Used to set and to cancel the timer operation.

10. SLEEP MODE AUTO BUTTON

Used to set sleep mode auto operation.

11. ROOM TEMPERATURE CHECKING BUTTON

Used to check the room temperature.

12. RESET BUTTON

Used prior to resetting time.

13. AUTO CLEAN BUTTON

Used to set auto clean mode.

14. PLASMA BUTTON

Used to start or stop the plasma-purification

function.

15. CLEAR ALL BUTTON

Used to cancel all timer setting.

16.

ENERGY SAVING COOLING BUTTON(OPTIONAL)

Used to save Energy.

17. LCD LUMINOSITY BUTTON(OPTIONAL)

Used to adjust LCD luminosity.

18. HORIZONTAL AIRFLOW DIRECTION CONTROL

BUTTON (OPTIONAL)

Used to set the desired horizontal airflow direction.

10 Multi Air Conditioner

To lower the temperature

To raise the temperature

Cooling

Auto

Operation

Healthy

Dehumidification

Heating

(Heat pump model only)

Air Circulation

CHAOS Air Fan speed is on low. Fan speed is on medium. Fan speed is on high.

Operating Instructions

Press the ON/OFF BUTTON to turn

the unit on.

The unit will respond with a beep.

Open the door of the remote controller and press the

operation mode button. Each time the button is pressed, the

operation mode is shifted in the direction of the arrow.

For cooling or heating operation set the desired indoor

temperature by pressing the ROOM TEMPERATURE

SETTING BUTTONS.

For cooling the temperature can be set within 18°C~30°C and

for heating the temperature range is 16°C~30°C.

Set the fan speed with the remote controller. You can select the fan speed in four steps-low,

medium, high and CHAOS by pressing the INDOOR FAN SPEED SELECTOR BUTTON.

Each time the button is pressed, the fan speed mode is shifted.

Natural wind by the CHAOS logic

❏

For fresher feeling, press the INDOOR FAN SPEED SELECTOR BUTTON selector and set to CHAOS mode.

In this mode, the wind blows like a natural breeze by automatically changing fan speed according to the CHAOS logic.

Operation Mode

Owner's Manual 11

ENGLISH

Operating Instructions

Healthy Dehumidification Operation

This operation circulates the air without cooling or heating. It can

be activated by pressing the OPERATION MODE SELECTION

BUTTON. Once the air circulation is activated you can select the

air speed by pressing the INDOOR FAN SPEED SELECTOR

BUTTON.

CHAOS Air economizes power consumption and prevents overcooling. The fan speed is automatically

changed from high to low or vice versa, depending on the ambient temperature.

NOTE

Air Circulation Operation

During Healthy Dehumidification Operation

❏ If you select the dehumidification mode on the OPERATION MODE SELECTION

BUTTON, the product starts to run the dehumidification function. It automatically sets

the room temperature and airflow volume to the best condition for dehumidification,

based on the sensed current room temperature.

In this case, however, the setting temperature is not displayed on the remote controller

and you are not able to control the room temperature either.

❏ During the healthy dehumidification function, the airflow volume is automatically set

according to the optimization algorithm responding to the current room temperature

status, so that the room condition is kept healthy and comfortable even in the very

humid season.

In this operation mode the actual setting temperature and the fan speed are

automatically set by the electronic control logic based on the current room

temperature. If you feel hot or cold press the temperature setting buttons

respectively for more cooling or heating effect.

NOTE : You cannot set the actual setting temperature and the indoor fan

speed in this operation mode. But you can use the Chaos swing

in this operation.

If the system is not operating as desired, switch manually to another mode.

Auto Operation

12 Multi Air Conditioner

Operating Instructions

Jet Cool Operation

NEO PLASMA Purification Operation (Optional)

❏ During auto clean function, only ON/OFF BUTTON, PLASMA BUTTON and AUTO CLEAN BUTTON can

be used.

NOTE

❏ During auto clean function, moistures left in indoor units after cooling operation or healthy dehumidification

operation can be removed.

•

Press the AUTO CLEAN BUTTON to activate this function.

•

Now whenever the unit is turned off, the indoor fan is still running for about 30

minutes internally without cooling or dehumidification operation. Also the louver is

closed.

•

This dries up any remains of moisture & cleans the unit internally.

•

If you press AUTO CLEAN BUTTON again during operation, this function is

cancelled.

Auto Clean Operation

Jet cool function can be used to cool the room quickly in hot summer. When this

function is turned on, the air conditioner runs in cooling operation mode with super

high fan speed and 18°C setting temperature for 30 minutes for fast and effective

cooling.

Plasma filter is a technology developed by LG to get rid of microscopic

contaminants in the intake air by generating a plasma of high charge electrons.

This plasma kills and destroys the contaminants completely to provide clean and

hygienic air.

You can activate this operation by pressing the JET COOL BUTTON.

To change from jet cool mode to high fan speed cooling mode, press the JET COOL BUTTON or

INIDOOR FAN SPEED SELECTOR BUTTON or the ROOM TERPERATURE SETTING BUTTON again.

• Jet cool function cannot be activated during heating mode.

• Art Cool and Art Cool Wide models close the side discharges during jet cool operation, for strong cooling.

NOTE

Plasma purification can be started by pressing the PLASMA BUTTON on the remote controller.

Repressing it will deactivate the operation.

This feature can be used in any operation mode and any fan speed can be used while

plasma filter is functioning.

NOTE

Owner's Manual 13

ENGLISH

The Display Luminosity can be adjusted by using the remote control.

Open the door of the remote controller, and press the LCD LUMINOSITY button.

Display will be dark. Press the button again to set bright display.

Forced operation

Operation procedures when the remote control can't be used. The operation will be started if the ON/OFF button

is pressed. If you want to stop operation, re-press the button.

Energy-Saving Cooling Mode (Optional)

Operating Instructions

Energy-saving cooling mode can save energy in cooling and healthy dehumidification operation, because it

can operate efficiently by setting body-adaptation time according to the change of time and temperature and

adjusting automatically desired temperature.

1. Press the ON/OFF BUTTON to start the unit.

2. Open the door of the remote controller.

Select cooling operation or healthy dehumidification operation.

3. Press the ENERGY-SAVING COOLING MODE BUTTON.

4. To cancel the energy-saving cooling mode, press the ENERGY-SAVING

COOLING MODE BUTTON again and unit will operate in previous

mode(Cooling or healty dehumidification mode).

Heat pump Model

Cooling Model

Room Temp. ≥ 24°C 21°C ≤ Room Temp. < 24°C Room Temp. < 21°C

Operating mode Cooling Cooling Healthy Dehumidification Heating

Indoor FAN Speed

High High High High

Setting Temperature

22°C 22°C 23°C 24°C

Test operation

During the TEST OPERATION, the unit operates in cooling mode at high speed fan, regardless of room temperature

and resets in 18 minutes.

During test operation, if remote controller signal is received, the unit operates as remote controller sets.

If you want to use this operation, Press and hold the ON/OFF button for 3~5 seconds, then the buzzer sound 1 "beep".

If you want to stop the operation, re-press the button.

Display Luminosity (Optional)

ON/OFF

button

Power

button

Power

button

Because Energy-Saving Cooling Mode is optional function, some product will not operate.

Because Display Luminosity is optional function, some product will not operate.

14 Multi Air Conditioner

Operating Instructions

Press the SLEEP MODE AUTO BUTTON to set the time when you want the unit to stop automatically.

The timer is programmed in one-hour increments by pressing the SLEEP MODE AUTO BUTTON 1 to 7 times.

The sleep mode is available for 1 to 7 times.

• The sleep mode will operate indoor fan at slow speed in cooling mode and at medium speed in heating mode

for pleasant sleep.

• Art Cool and Art Cool Wide (non-Deluxe) close the lower discharge partially in sleep mode for pleasant sleep.

In cooling mode or healthy dehumidification mode:

The setting temperature will rise automatically two times by 1°C over next consecutive 30 minutes (2°C in 1

hour) for a comfortable sleep. Now this will be the final setting temperature as long as sleep mode is functioning.

NOTE

• If you wish to cancel all timer setting, press the CLEAR ALL BUTTON.

• If you wish to cancel each timer setting, press the

TIMER BUTTON to turn timer sleep on or off as you want.

And then press the SET/CLEAR BUTTON aiming the remote

controller at the signal receptor.

(The timer lamp on the air conditioner and the display will go off.)

1. Press the TIMER BUTTON for 3 seconds.

2. Press TIME SETTING BUTTONS

until the desired time is set.

Check the indicator for A.M. and

P.M.

3. Press the SET / CLEAR BUTTON.

NOTE

Timer On Timer Off

1. Press the TIMER BUTTON to

turn timer on or off.

2. Press TIME SETTING BUTTONS

until the desired time is set.

3. Press the SET / CLEAR BUTTON.

Select one of the following 2 types of operation.

NOTE

Setting the Current Time

To cancel the timer setting

Timer Setting

Sleep Mode

Owner's Manual 15

Operating Instructions

ENGLISH

The up/down airflow (Vertical airflow) can be

adjusted by using the remote controller.

1. Press the ON/OFF BUTTON to start the unit.

2. Press CHAOS SWING BUTTON.

3. The louvers will swing up &

down automatically.

4. To stop the louver at a desired

angle, press again

The left/right(Horizontal airflow) can be adjusted

by using the remote control.

1. Press the ON/OFF BUTTON to start the unit.

2. Press the HORIZONTAL AIRFLOW

DIRECTION BUTTON.

3. The louvers will swing left &

right automatically.

4. To stop the louvers at a desired

angle, press again.

Vertical / Horizontal Airflow Direction Control (Optional)

• By pressing the CHAOS SWING BUTTON the horizontal air flow direction is changed automatically based on the chaos

algorithm to distribute the air in the room evenly and at the same time to make the human body feel most comfortable as if

enjoying natural breeze.

• Manually moving the vertical air flow direction louver by hand could damage the mechanism.When the unit is shut off, the

up/down airflow direction louver will close the air outlet vent of the system.

• The Chaos Swing may not run correctly during sleep mode.

NOTE

This feature is enabled by factory default setting, but you can disable it by pressing the

ON/OFF button for 6 seconds. The unit will beep twice and the indicator lamp(2) will blink 4

times.

To enable it, press the button again for 6 seconds. The unit will beep twice and the indicator

lamp(1) will blink 4 times.

NOTE

This function is useful in the situation of power failure.

When power regains after a failure this feature restore the previous operating condition

and the air conditioner will run in the same settings.

Auto Restart Function

Because Horizontal Airflow Direction Control is optional function, some product will not operate.

16 Multi Air Conditioner

Maintenance and Service

Before performing any maintenance, turn off the main power to the system, disconnect the circuit breaker and

unplug the power cord.

Grille, Case, and Remote Control

❏ Turn the system off before cleaning.

To clean, wipe with a soft, dry cloth. Do not use bleach or abrasives.

Supply power must be disconnected before cleaning the indoor unit.

NOTE

AIR FILTERS

The air filters behind the front grille should be checked

and cleaned once in every 2 weeks or more often if

neccessary.

Open the front panel as shown.

2. Then pull the filter tab slightly forward to remove

the air filter.

3. Clean the filter with a vacuum cleaner or warm, soapy

water.

• If dirt is conspicuous, wash with a solution of

detergent in lukewarm water.

• If hot water (40°C or more) is used, it may be

deformed.

4. After washing with water, dry well in the shade.

5. Re-install the air filter.

PLASMA FILTER

The PLASMA filter behind the air filters should be

checked and cleaned once in every 3 months or more

often if necessary.

1. After removing the air filters, pull slightly forward to

remove the PLASMA filter.

2. Remove dust with vacuum cleaner or air.

(You should not try to wash with water).

3. Note the cuts of electric discharge lines.

4. Re-install the PLASMA filter to the original position.

❏

Never use any of the followings:

• Water hotter than 40°C

Could cause deformation and/or discoloration.

• Volatile substances

Could damage the surfaces of the air

conditioner.

Plasma filter

Front panel

Don’t touch this PLASMA Filter within 10

seconds after opening the inlet grille, it may

cause an electric shock.

Artcool Mirror Type

Owner's Manual 17

Maintenance and Service

ENGLISH

Artcool Type

Clean the unit with a soft dry cloth. Do not use bleach or abrasives.

Never use any of these

• Water hotter than 40°C. It may cause deformation and discoloration.

• Volatile substances. They may damage the surface of the air conditioner.

Air Filters

The air filters behind the front panel / grill should be checked and

cleaned once in every 2 weeks or more often if necessary. To remove

the filters see the self explanatory diagrams for each model type.

Clean the filters with a vacuum cleaner or warm soapy water. If dirt is

not easily removed, wash with a solution of detergent in luke warm water.

Dry well in shade after washing and reinstall the filters back in place.

Plasma Filters

The plasma filters behind the air filter should be checked and cleaned

once in every 3 months or more often if necessary. To remove the filters see

the self explanatory diagrams for each model type. Clean the filters with a vacuum

cleaner. If it is dirty wash it with water and dry well in shade an install back in

place.

Deodorizer Filters

Remove the deodorizer filters behind the air filter and expose them in direct

sunlight for 2 hours.

And then insert these filters into original position.

Removal of Filters

1. Art Cool Type :

Pull out the upper section of front panel and lift it up. Take out a filter with front panel held.

With PUSH button pressed, pull out grip to take out a plasma filter. Dry it completely in the shade after cleaning.

Then set a plasma filter and a filter orderly. Put the hook of front panel onto the hanger, in order to close the front

panel.

Don't touch this plasma filter within 10 seconds after opening the inlet grille, it may cause an electric shock.

Front panel

Plasma filter

Front panel hook

Hook-hanger

Air filter

18 Multi Air Conditioner

Maintenance and Service

How to replace picture & photograph (Art Cool Type2)

1. Turn off power and then open

the upper part of front panel.

2. Pull out the both links of lower

part of front panel, as

described in the below picture.

3. Push and close the top part of

the front panel and then pull

the bottom part of the panel

forward until it is secured.

4. Take out picture. 5. Turn upside-down of the

picture and turn over mat, then

take off a protective tape

attached at the mat.

6. Place the picture/photograph

between the exited picture and

mat. (Recommended size of a

photo/picture: 450mm x

450mm)

7. Cover mat and press down

with hand(s) until contacting

closely.

8. Slide the photo graph/drawing

requested under both hanger

parts as following, and fix them.

Press the front panel lightly to

close.

9. Push both links of lower part of

panel inside and fix it. Then

turn on.

In case a mat is not used, recommended size of a photo/picture:

522mm x 522mm

When powering on after replacing filter and picture,

the front panel doesn't intervene.

Mat

450mm

522mm

Mat

Protective tape

Owner's Manual 19

ENGLISH

Maintenance and Service

When the air conditioner is not going to be used for a long time.

Operation Tips

Operate the air conditioner on Air

circulation mode (Refer to page 11) for 2

to 3 hours.

• This will dry out the internal mechanisms.

When air conditioner is not going to be

used for a long time.

When the air conditioner is to be used again.

Turn off the circuit breaker, and

disconnect the power cable.

Remove the batteries from the Remote

Controller.

CAUTION:

Turn off the circuit

breaker when the air conditioner is not

going to be used for a long time.

Dirt may collect and may cause a fire.

Clean the air filter and install it in the

indoor unit.

(Refer to page 14~15 for cleaning filters.)

Check that the air inlet and outlet of the

indoor/outdoor unit are not blocked.

Do not overcool the room.

This is not good for the health

and wastes electricity.

Make sure that the doors

and windows are shut tight.

Avoid opening doors and

windows if possible to keep the

cool air in the room.

Keep blinds or curtains

closed.

Do not let direct sunshine enter

the room when the air

conditioner is in operation.

Clean the air filter regularly.

Blockages in the air filter reduce

the airflow and lower cooling

and dehumidifying effects.

Clean at least once every two

weeks.

Keep the room temperature

uniform.

Adjust the vertical and

horizontal airflow direction to

ensure a uniform temperature in

the room.

Ventilate the room

occasionally.

Since windows are kept closed,

it is a good idea to open them

and ventilate the room now and

then.

20 Multi Air Conditioner

Maintenance and Service

Troubleshooting

Check the following points before requesting repairs or service.... If the fault persists, please contact your dealer or service center.

Case Explanation See page

The air conditioner does not

operate.

The room has a peculiar

odor.

It seems that condensation

is leaking from the air

conditioner.

Air conditioner does not

operate for about 3 minutes

after turning on.

Does not cool or heat

effectively.

The air conditioner

operation is noisy.

Remote Controller display is

faint, or no display at all.

Crack sound is heard.

• Check room temperature setting?

• Check if circuit breaker is on?

• Check that this is not a damp smell exuded by

the walls, carpet, furniture, or cloth items in the

room.

• Check the drain hose is connected tight or if

indoor unit is installed even.

• This is the protector of the mechanism.

• Wait about 3 minutes and operation will begin.

• About 3 minutes delay is applied to protect

compressor from frequenty on/off.

• Is the air filter dirty? See air filter cleaning

instructions.

• Has the temperature been set correctly?

• Are the indoor unit's air inlet or outlet vents

obstructed?

• For a noise that sounds like water flowing.

-This is the sound of refrigerant flowing inside

the air conditioner unit.

• For a noise that sounds like the compressed

air releasing into atmosphere.

-This is the sound of the dehumidifying water

being processed inside the air conditioning

unit.

• Are the batteries depleted?

• Are the batteries inserted in the opposite (+)

and (-) directions?

• This sound is generated by the

expansion/constriction of the front panel, etc.

due to changes of temperature.

14~15

La page charge ...

LG MA12AH1-M Le manuel du propriétaire

Marque: LG

Modèle: MA12AH1-M

Catégorie: Climatiseurs split-system

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

italiano: LG MA12AH1-M Manuale del proprietario
English: LG MA12AH1-M Owner's manual
español: LG MA12AH1-M El manual del propietario
Deutsch: LG MA12AH1-M Bedienungsanleitung
Nederlands: LG MA12AH1-M de handleiding
português: LG MA12AH1-M Manual do proprietário

LG MA12AH1-M Le manuel du propriétaire

LG MA12AH1-M Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents