Worx WG305.1 Le manuel du propriétaire

Marque: Worx

Modèle: WG305.1

Catégorie: Tronçonneuses électriques

Taper: Le manuel du propriétaire

Electric Chain Saw EN

Tronçonneuse électrique prime F

Sierra eléctrica ES

P05

P18

P33

WG305 WG305.1 WG305.2

6 7

523

115

221

EN: Injecting grease to lubricate

ES: Inyectando grasa para lubricar

F: Injectez la graisse pour lubrifier

12 11

Kink/Plis/Torcimiento

EN: Bar / F: Bar

ES: Barra de guía

A B1 B2

C2C1

E1 E2

G H1

H3 I

K L

EN: Injecting grease to lubricate

ES: Inyectando grasa para lubricar

F: Injectez la graisse pour lubrifier

12 11

Kink/Plis/Torcimiento

EN: Bar / F: Bar

ES: Barra de guía

A B1 B2

C2C1

E1 E2

G H1

H3 I

K L

Electric Chain Saw EN

PRODUCT SAFETY

WARNING: Some dust created by

power sanding, sawing, grinding,

drilling and other construction activities

contains chemicals known to the state

of California to cause cancer, birth

defects or other reproductive harm.

Some examples of these chemicals are:

• Lead from lead-based paints;

• Crystalline silica from bricks and

cement and other masonry products

and

• Arsenic and chromium from

chemically-treated lumber.

Your risk from these exposures varies,

depending on how often you do this

type of work. To reduce your exposure

to these chemical:

• Work in a well ventilated area, and

• Work with approved safety

equipment, such as those dust masks

that are specially designed to ﬁlter

out microscopic particles.

WARNING: This product can

expose you to chemicals including

lead, phthalate or bisphenol A which

are known to the State of California to

cause cancer, birth defects or other

reproductive harm. Wash your hands

after use. For more information go to

www.P65Warnings.ca.gov.

GENERAL POWER TOOL

SAFETY WARNINGS

WARNING: Read all safety warnings

and instructions. Failure to follow

the warnings and instructions may result in

electric shock, ﬁre and/or serious injury.

Save all warnings and instructions for

future reference.

The term power tool in the warnings refer to

your electric (corded) power tool or battery-

operated (cordless) power tool.

1. WORK AREA SAFETY

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in

explosive atmospheres, such as in the

presence of ﬂammable liquids, gases

or dust. Power tools create sparks which

may ignite the dust or fumes.

c) Keep children and bystanders

away while operating a power tool.

Distractions can cause you to lose control.

2. ELECTRICAL SAFETY

a) Power tool plugs must match the

outlet. Never modify the plug in

any way. Do not use any adapter

plugs with grounded power tools.

Unmodiﬁed plugs and matching outlets

will reduce risk of electric shock.

b) Avoid body contact with grounded

surfaces such as pipes, radiators,

ranges and refrigerators. There is an

increased risk of electric shock if your body

is grounded.

c) Do not expose power tools to rain or

wet conditions. Water entering a power

tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use

the cord for carrying, pulling or

unplugging the power tool. Keep cord

away from heat, oil, sharp edges or

moving parts. Damaged or entangled

cords increase the risk of electric shock.

e) When operating a power tool

outdoors, use an extension cord

suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of

electric shock.

f) If operating a power tool in a damp

location is unavoidable, use a ground

fault circuit interrupter (GFCI)

protected supply. Use of an GFCI

reduces the risk of electric shock.

3. PERSONAL SAFETY

a) Stay alert, watch what you are

doing and use common sense when

operating a power tool. Do not use

a power tool while you are tired or

under the inﬂuence of drugs, alcohol

or medication. A moment of inattention

while operating power tools may result in

serious personal injury.

b) Use personal protective equipment.

Electric Chain Saw EN

Always wear eye protection. Protective

equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing

protection used for appropriate conditions

will reduce personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the off-position before

connecting to power source and/or

battery pack, picking up or carrying

the tool. Carrying power tools with your

ﬁnger on the switch or energizing power

tools that have the switch on invites

accidents.

d) Remove any adjusting key or wrench

before turning the power tool on. A

wrench or a key left attached to a rotating

part of the power tool may result in

personal injury.

e) Do not overreach. Keep proper

footing and balance at all times. This

enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose

clothing or jewelry. Keep your hair,

clothing and gloves away from

moving parts. Loose clothes, jewelry or

long hair can be caught in moving parts.

g) If devices are provided for the

connection of dust extraction and

collection facilities, ensure these are

connected and properly used. Use of dust

collection can reduce dust-related hazards.

4. POWER TOOL USE AND CARE

a) Do not force the power tool. Use

the correct power tool for your

application. The correct power tool will

do the job better and safer at the rate for

which it was designed.

b) Do not use the power tool if the

switch does not turn it on and off.

Any power tool that cannot be controlled

with the switch is dangerous and must be

repaired.

c) Disconnect the plug from the power

source and/or the battery pack from

the power tool before making any

adjustments, changing accessories,

or storing power tools. Such preventive

safety measures reduce the risk of starting

the power tool accidentally.

d) Store idle power tools out of the

reach of children and do not allow

persons unfamiliar with the power

tool or these instructions to operate

the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools. Check for

misalignment or binding of moving

parts, breakage of parts and any other

condition that may affect the power

tools operation. If damaged, have the

power tool repaired before use. Many

accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with

sharp cutting edges are less likely to bind

and are easier to control.

g) Use the power tool, accessories and

tool bits etc., in accordance with

these instructions and in the manner

intended for the particular type of

power tool, taking into account the

working conditions and the work to

be performed. Use of the power tool for

operations different from those intended

could result in a hazardous situation.

5. SERVICE

a) Have your power tool serviced by

a qualiﬁed repair person using only

identical replacement parts. This will

ensure that the safety of the power tool is

maintained.

CHAIN SAW SAFETY

WARNINGS

1. Keep all parts of the body away from

the saw chain when the chain saw is

operating. Before you start the chain

saw, make sure the saw chain is not

contacting anything. A moment of

inattention while operating chain saws may

cause entanglement of your clothing or

body with the saw chain.

2. Always hold the chain saw with your

right hand on the rear handle and your

left hand on the front handle. Holding

the chain saw with a reversed hand

Electric Chain Saw EN

conﬁguration increases the risk of personal

injury and should never be done.

3. Hold the power tool by insulated

gripping surfaces only, because the

saw chain may contact hidden wiring

or its own cord. Saw chains contacting

a live wire may make exposed metal parts

of the power tool live and could give the

operator an electric shock.

4. Wear safety glasses and hearing

protection. Further protective

equipment for head, hands, legs

and feet is recommended. Adequate

protective clothing will reduce personal

injury by ﬂying debris or accidental contact

with the saw chain.

5. Do not operate a chain saw in a tree.

Operation of a chain saw while up in a tree

may result in personal injury.

6. Always keep proper footing and

operate the chain saw only when

standing on ﬁxed, secure and level

surface. Slippery or unstable surfaces

such as ladders may cause a loss of

balance or control of the chain saw.

7. When cutting a limb that is under

tension be alert for spring back. When

the tension in the wood ﬁbers is released the

spring loaded limb may strike the operator

and/or throw the chain saw out of control.

8. Use extreme caution when cutting

brush and saplings. The slender material

may catch the saw chain and be whipped

toward you or pull you off balance.

9. Carry the chain saw by the front

handle with the chain saw switched

off and away from your body. When

transporting or storing the chain saw

always apply the guide bar cover.

Proper handling of the chain saw will

reduce the likelihood of accidental contact

with the moving saw chain.

10.Follow instructions for lubricating,

chain tensioning and changing

accessories. Improperly tensioned

or lubricated chain may either break or

increase the chance for kickback.

11.Keep handles dry, clean, and free from

oil and grease. Greasy, oily handles are

slippery causing loss of control.

12.

Cut wood only. Do not use chain

saw for purposes not intended. For

example: do not use chain saw for

cutting plastic, masonry or non-wood

building materials. Use of the chain saw

for operations different than intended could

result in a hazardous situation.

13.Recommendation for the use of a

residual current device with a tripping

current of 30mA or less.

CAUSES AND OPERATOR PREVENTION

OF KICKBACK:

Kickback may occur when the nose or tip of the

guide bar touches an object, or when the wood

closes in and pinches the saw chain in the cut.

Tip contact in some cases may cause a

sudden reverse reaction, kicking the guide bar

up and back towards the operator.

Pinching the saw chain along the top of the

guide bar may push the guide bar rapidly back

towards the operator.

Either of these reactions may cause you to

lose control of the saw which could result in

serious personal injury. Do not rely exclusively

upon the safety devices built into your saw.

As a chain saw user, you should take several

steps to keep your cutting jobs free from

accident or injury.

Kickback is the result of tool misuse and/or

incorrect operating procedures or conditions

and can be avoided by taking proper

precautions as given below:

- Maintain a ﬁrm grip, with thumbs

and ﬁngers encircling the chain saw

handles, with both hands on the saw

and position your body and arm to

allow you to resist kickback forces.

Kickback forces can be controlled by the

operator, if proper precautions are taken.

Do not let go of the chain saw.

- Do not overreach and do not cut

above shoulder height. This helps

prevent unintended tip contact and

enables better control of the chain saw in

unexpected situations.

- Only use replacement bars and

chains speciﬁed by the manufacturer.

Incorrect replacement bars and chains may

cause chain breakage and/or kickback.

- Follow the manufacturer’s sharpening

and maintenance instructions for the

Electric Chain Saw EN

saw chain. Decreasing the depth gauge

height can lead to increased kickback.

SAFETY RULES FOR EXTENSION CORD

Make sure your extension cord is in good

condition. When using an extension cord,

be sure to use one heavy enough to carry

the current your product will draw. An

undersized extension cord will cause a drop

in line voltage resulting in loss of power and

overheating. Table 1 shows the correct size to

use depending on cord length and nameplate

ampere rating. If in doubt, use the next

heavier gage. The smaller the gage number,

the heavier the cord. To reduce the risk of

disconnection of appliance cord from the

extension cord during operating:

I) Make a knot as shown in Figure 1; or

II) Use one of the plug-receptacle retaining

straps or connectors described in this manual.

Table 1 Minimum gauge for extension cords

Volts Total length of cord in feet

120V 25 50 100 150

Ampere rating

more than not

more than

AWG

0-6 18 16 16 14

6-10 18 16 14 12

10-12 16 16 14 12

12-16 14 12

Not

recommended

Figure 1

METHOD OF SECURING EXTENSION

CORD

SET

APPLIANCE CORD

(A) TIE CORD AS SHOWN

(B) CONNECT PLUG AND RECEPTACLE

SAVE THESE INSTRUCTIONS

INSTRUCTIONS CONCERNING THE

PROPER TECHNIQUES FOR BASIC

FELLING, LIMBING, AND CROSS-

CUTTING

1. Felling a tree

When bucking and felling operations are

being performed by two or more persons at

the same time, the felling operations should

be separated from the bucking operation by

a distance of at least twice the height of the

tree being felled. Trees should not be felled in

a manner that would endanger any person,

strike any utility line or cause any property

damage. If the tree does make contact with

any utility line, the company should be

notiﬁed immediately.

The chain saw operator should keep on the

uphill side of the terrain as the tree is likely to

roll or slide downhill after it is felled.

An escape path should be planned and

cleared as necessary before cuts are started.

The escape path should extend back and

diagonally to the rear of the expected line of

fall as illustrated in Figure 1.

Before felling is started, consider the natural

lean of the tree, the location of larger branches

and the wind direction to judge which way the

tree will fall.

Remove dirt, stones, loose bark, nails, staples

and wire from the tree.

2. Notching undercut

Make the notch 1/3 the diameter of the

tree, perpendicular to the direction of falls

as illustrated in Figure1. Make the lower

horizontal notching cut (W) ﬁrst. This will help

to avoid pinching either the saw chain or the

guide bar when the second notch (X) is being

made.

3. Felling back cut

Make the felling back cut (Y) at least 50 mm

higher than the horizontal notching cut as

illustrated in Figure 2. Keep the felling back

cut parallel to the horizontal notching cut.

Make the felling back cut so enough wood is

left to act as a hinge. The hinge wood keeps

the tree from twisting and falling in the wrong

Electric Chain Saw EN

the top (overbuck) , avoid contacting ground

as this will greatly reduce the chain sharpness.

2˝

2/3

1/3

2/3

1/3

Fig.2

Fig.3

Fig.4

Fig.5

Fig.6

Fig.7

When the log is supported on one end, as

illustrated in Figure 5, cut 1/3 the diameter from

the underside (underbuck)(1). Then make the

ﬁnished cut by overbucking(2) to meet the ﬁrst cut.

2˝

2/3

1/3

2/3

1/3

Fig.2

Fig.3

Fig.4

Fig.5

Fig.6

Fig.7

When the log is supported on both ends, as

illustrated in Figure 6, cut 1/3 the diameter

from the top (overbuck)(1). Then make the

ﬁnished cut by underbucking(2) the lower 2/3

to meet the ﬁrst cut.

2˝

2/3

1/3

2/3

1/3

Fig.2

Fig.3

Fig.4

Fig.5

Fig.6

Fig.7

direction. Do not cut through the hinge.

As the felling gets close to the hinge, the tree

should begin to fall. If there is any chance

that the tree may not fall in desired direction

or it may rock back and bind the saw chain,

stop cutting before the felling back cut is

complete and use wedges of wood, plastic or

aluminium (Z) to open the cut and drop the

tree along the desired line of fall. (

)

When the tree begins to fall remove the chain

saw from the cut, stop the motor, put the

chain saw down, then use the retreat path

planned (

). Be alert for overhead limbs

falling and watch your footing.

2˝

2/3

1/3

2/3

1/3

Fig.2

Fig.3

Fig.4

Fig.5

Fig.6

Fig.7

4. Limbing a tree

Limbing is removing the branches from a

fallen tree. When limbing leave larger lower

limbs to support the log off the ground.

Remove the small limbs in one cut as

illustrated in Figure 3. Branches under tension

should be cut from the bottom up to avoid

binding the chain saw.

2˝

2/3

1/3

2/3

1/3

Fig.2

Fig.3

Fig.4

Fig.5

Fig.6

Fig.7

5. Bucking a log

Bucking is cutting a log into lengths. It is

important to make sure your footing is ﬁrm

and your weight is evenly distributed on both

feet. When possible, the log should be raised

and supported by the use of limbs, logs or

chocks. Follow the simple directions for easy

cutting.

When the log is supported along its entire

length as illustrated in Figure 4, it is cut from

Electric Chain Saw EN

SYMBOLS

To reduce the risk of injury, user

must read instruction manual.

Wear ear protection

Wear eye protection

Wear dust mask

Double insulation

Do not expose to rain

Remove plug from the mains

immediately if the cable is damaged

or cut.

Contact of the guide bar tip with any

object should be avoided.

Tip contact can cause the guide

bar to move suddenly upward and

backward, which can cause serious

injury.

Always use two hands when

operating the chain saw.

When bucking on a slope always stand on

the uphill side of the log, as illustrated in

Figure 7. When “cutting through”, to maintain

complete control release the cutting pressure

near the end of the cut without relaxing your

grip on the chain saw handles. Don’t let the

chain contact the ground. After completing the

cut, wait for the saw chain to stop before you

move the chain saw. Always stop the motor

before moving from tree to tree.

2˝

2/3

1/3

2/3

1/3

Fig.2

Fig.3

Fig.4

Fig.5

Fig.6

Fig.7

Electric Chain Saw EN

1. REAR HANDLE

2. ON/OFF SWITCH/TRIGGER

3. LOCK-OUT BUTTON

4. OIL LEVEL WINDOW

5. OIL FILLER CAP

6. FRONT HANDLE

7. HAND GUARD

8. BUMPER SPIKE

9. GUIDE BAR

10. CHAIN

11. CHAIN TENSIONING KNOB

12. CHAIN COVER

13. EXTENSION CORD HOLDER

14. REAR HAND GUARD

15. DRIVE SPROCKET

16. CHAIN DIRECTION SYMBOL

17. OIL OUTLET

18. BAR PAD

19. FASTENING BAR HOLE

20. BAR LOCATING TABS

21. BAR AND CHAIN STORAGE/TRANSPORTATION COVER (SHEATH)*

22. BAR TENSIONING PLATE (See Fig. A )

23. PUMP BUTTON/BULB

* Not all the accessories illustrated or described are included in standard delivery.

Electric Chain Saw EN

TECHNICAL DATA

Voltage 120V~60Hz

Amps 8A

Bar length 14“

Chain speed 28ft/s

Oil tank capacity 120ml

Chain pitch 3/8"

Number of chain drive links 52

Chain gauge 0.050"

Chain type

ES: 3/8LP.050 52E / QIRUI: A1-52 / KANGXIN: 3/8LP-52/OREGON:

91PX052X

Bar type

ES: ES140SDEA041 / QIRUI: P014-50SR / KANGXIN: AP14-52-507P/

OREGON: 140SDEA041

Weight( chain & bar included) 6.6 lbs

Protection class

/II

ACCESSORIES

WG305 WG305.1 WG305.2

Chain 1 1 1

Guide Bar 1 1 1

Transportation Cover 1 1 1

Only use the appropriate accessories intended for this tool. Accessory information can be found

on the product packaging, at a WORX dealer or on our website at www.worx.com.

Electric Chain Saw EN

ASSEMBLY

WARNING! Do not connect the

chain saw to the power supply

before it is completely assembled.

Always use gloves when handling the

chain.

CHAIN AND GUIDE BAR ASSEMBLY

1. Unpack all parts carefully.

2. Place the chain saw on a solid, level

surface.

3. Use only genuine WORX chains or

those recommended for Guide Bar.

4. Slide the Chain (10) in the slot around the

Guide Bar (9). Ensure the Chain is in correct

running direction by comparing it to the

chain icon on the guide bar, or referring to

the Chain Direction Symbol (16) found on

the saw body. Ensure the Bar Tensioning

Plate (22) is facing outwards. (See Fig. A)

5. Fit the Chain onto the Drive Sprocket (15),

so that the Fastening Bar Hole (19) and the

two Bar Locating Tabs (20) on the Bar Pad

(18) ﬁt into the keyway of the opening on

the Guide Bar (9). (See Fig. B1, B2)

6. Assure all parts are seated properly. Make

sure the drive links are fully seated in the

drive sprocket (See Fig. C1), avoiding a kink

as shown in Fig. C2. If kink occurs, pick up

on the chain at the guide bar just ahead of

the kink and then pull the kink out.

NOTE: Chain should rotate freely and

be free of kinks.

7. Fit the Chain Cover (12) and tighten

the Chain Cover by turning the Chain

Tensioning Knob (11) clockwise until it is

tight. (See Fig. D)

WARNING! The chain is not

yet tensioned. Tensioning the

chain applies as described under

“TENSIONING CHAIN”. The chain now

needs to be inspected to make sure it is

properly tensioned.

TENSIONING CHAIN (See Fig. E1, E2)

NOTE: New saw chains will stretch. Check the

chain tension frequently when ﬁrst used and

tighten when the Chain (10) becomes loose

around the Guide Bar (9).

WARNING:

• Unplug chain saw from power source

before adjusting saw chain tension.

• Cutting edges on chain are sharp.

Use protective gloves when handling

chain.

• Maintain proper chain tension always.

A loose chain will increase the risk

of kickback. A loose chain may jump

out of guide bar groove. This may

injure operator and damage chain. A

loose chain will cause chain, bar, and

sprocket to wear rapidly.

1. Place the chain saw on any suitable ﬂat

surface.

2. Turn the Chain Tensioning Knob (11)

clockwise until it is hand tight.

NOTE: The tension is automatically

increased while the Chain Tensioning Knob

(11) is being turned in a clockwise direction.

The built-in ratchet mechanism prevents

the chain tension from loosening.

3. Tilt the saw forward (See E1) where the

Guide Bar (9) tip is pushed in an upward

direction. This will remove slack from the

chain.

4. Fully tighten the Chain Tensioning Knob (11)

by turning it clockwise.(See E1)

5. Double check the tension set by the

automatic Chain Tensioning Knob. The

correct chain tension is reached when the

Chain (10) can be raised approx. half the

drivelink depth from the Guide Bar (9) in

the center. This should be done by using

one hand to raise the chain against the

weight of the machine. (See Fig. E2)

NOTE: The Chain (10) is properly tensioned

when it can be lifted off of the Guide Bar

(9) and the drivelink is within the rail of the

Guide Bar (9).

NOTE: The Chain (10) will stretch while

cutting and lose proper tension. When the

chain becomes loose, completely unscrew

the Chain Tensioning Knob (11) or turn the

knob around three full turns in a counter-

clockwise direction, then retighten the

Chain Tensioning Knob (11) to properly

reset the chain tension by repeating Step

1-4 listed above.

Electric Chain Saw EN

LUBRICATION

IMPORTANT: The chain saw is

not supplied ﬁlled with oil. It is

essential to ﬁll with oil before use.

Never operate the chain saw without

chain oil or at an empty oil tank level, as

this will result in extensive damage to

the product.

Filling oil tank:

WARNING: Unplug chain saw from

power source before ﬁlling the oil

tank.

1. Set chain saw on any suitable surface with

Oil Filler Cap (5) facing upward.

2. Clean area around the Oil Filler Cap with

cloth and unscrew the cap by turning it

counter clockwise.

3. Add bar and chain oil until reservoir is full.

4. Avoid dirt or debris entering oil tank, reﬁt

Oil Filler Cap (5) and tighten by turning

clockwise until hand tight.

IMPORTANT: To allow venting of

the oil reservoir, small breather

channels are provided between the Oil

Filler Cap and the strainer, to prevent

leakage ensure machine is left in a

horizontal position (Oil Filler Cap (5)

uppermost) when not in use.

It is important to use only the

recommended standard bar and chain

oil (Grade: ISO VG32) to avoid damage

to the chain saw.This can be found at

the location you purchased this saw or

your local hardware store. Never use

recycled/old oil. Use of non approved oil

will void the warranty

Oiling chain

Always check oil level before using saw. Do

not attempt to operate the oil system while

saw is in operation. To oil chain, press the

Bulb (23). Oil will feed through the Oil Outlet

(17) onto the Guide Bar (9) and chain. Press

the Bulb (23) on Oil Filler Cap at least once

before each cut (see Fig. F)

OPERATION

1. SWITCHING ON AND OFF (See Fig. G)

ATTENTION: Check the voltage and

current supply: The voltage and

current supply must comply with the

ratings on the product plate.

For switching on the tool, press the Lock-

Out Button (3), then fully press the On/Off

Switch (2) and hold in this position. The Lock-

Out Button can now be released.

For switching off, release the On/Off Switch .

2. CUTTING

IMPORTANT: Is the oil reservoir

ﬁlled? Check the Oil Level Window

(4) prior to starting and regularly during

operation.(See Fig. H1) Reﬁll oil when

oil level is low. A full oil tank will last

approx. 12 minutes of cutting depending

on sawing intensity and stops. Check

recent replaced chain tension about

every 10 minutes during operation.

1) Connect saw to extension cord. Connect

extension cord to power supply.

(See Fig. H2 )

2) Make sure section of log to be cut is not

laying on the ground. This will keep the

chain (10) from touching the ground as it

cuts through the log.

Touching the ground while the Chain is

moving is dangerous and will dull the

Chain.

3) Use both hands to grip saw. Always use

left hand to grip Front Handle (6) and

right hand to grip Rear Handle (1). Use a

ﬁrm grip. Thumbs and ﬁngers must wrap

around saw handles. (See Fig.H3 )

4) Make sure your footing is ﬁrm. Keep feet

shoulder width apart. Distribute your

weight evenly on both feet.

5) When ready to make a cut, push the

Lock-Out Button (3) completely in with the

right thumb and squeeze the trigger. This

will turn the saw on. Releasing the trigger

will turn the saw off. Make sure the saw is

running at full speed before starting a cut.

6) When starting a cut, slowly place moving

chain against the wood. The wood should

be as close to the saw body as possible.

Hold saw ﬁrmly in place to avoid possible

bouncing or skating (sideways movement)

of saw.

7) Guide the saw using light pressure and

do not put excessive force on the saw,

letting the saw do its work. The motor will

overload and can burn out. It will do the

job better and safer at the rate for which it

was intended.

Electric Chain Saw EN

8) Remove the saw from a cut with the saw

running at full speed. Stop the saw by

releasing the On/off Switch (2). Make sure

the chain has stopped before setting the

saw down.

9) Keep practicing on scrap logs in a secure

working area until you are comfortable and

can saw with ease, using a ﬂuid motion

and a steady cutting rate.

KICKBACK SAFETY DEVICES ON THIS

SAW

This saw has a low-kickback chain and

reduced kickback Guide Bar. Both items

reduce the chance of kickback. However,

kickback can still occur with this saw.

The following steps will reduce the risk of

kickback.

• Use both hands to grip saw while saw is

running. Use ﬁrm grip. Thumbs and ﬁngers

must wrap around saw handles.

• Keep all safety items in place on saw.

Make sure they work properly.

• Do not overreach or cut above shoulder

height.

• Keep solid footing and balance at all times.

• Stand slightly to left side of saw. This keeps

your body from being in direct line with

chain.

• Do not let Guide Bar nose touch anything

when chain is moving.

• Never try cutting through two logs at same

time. Only cut one log at a time.

• Do not bury the Guide Bar nose or try

plunge cut (boring into wood using Guide

Bar nose).

• Watch for shifting of wood or other forces

that may pinch chain.

• Use extreme caution when reentering a

previous cut.

• Use only the low-kickback chain and Guide

Bar (9) that were supplied with this chain

saw or recommended.

• Never use a dull or loose chain. Keep chain

sharp with proper tension.

HOW TO USE SAW SAFELY

1. Use the chain saw only with secure

footing.

2. Hold the chain saw at the right-hand side

of your body. (See Fig. I)

3. The Chain (10) must be running at full speed

before it makes contact with the wood.

4. Use the Bumper Spikes (8) to secure the

saw onto the wood before starting to cut.

5. Use the Bumper Spikes as a leverage point

while cutting. (See Fig. J)

6. Do not operate the chain saw with arms

fully extended, or attempt to saw areas

which are difﬁcult to reach, or stand on a

ladder while sawing. (See Fig. K)

7. Never use the chain saw above shoulder

height.

CUTTING WOOD UNDER TENSION (See

Fig. L)

WARNING: When cutting a limb

that is under tension, use extreme

caution. Be alert for wood springing

back. When wood tension is released,

limb could spring back and strike

operator causing severe injury or death.

When sawing logs supported on both ends,

start the cut from above (Y) (overbuck) about

1/3 of the diameter into the log and then

ﬁnish the cut (Z) from below, in order to avoid

contact of the chain saw with the ground.

When sawing logs supported on only one

end, start the cut from below (Y) about 1/3

of the diameter into the log (underbuck) and

ﬁnish the cut from above (Z) in order to avoid

log splitting or jamming of the chain saw.

SAW MAINTENANCE

Follow maintenance instructions in this

manual. Proper cleaning of saw and chain and

Guide Bar maintenance can reduce chances

of kickback. Inspect and maintain saw after

each use. This will increase the service life of

your saw.

NOTE: Even with proper sharpening, risk of

kickback can increase with each sharpening.

MAINTENANCE AND

STORAGE OF CHAIN SAW

If the replacement of the supply cord is

necessary, this has to be done by the

manufacturer or his agent in order to avoid a

safety hazard.

1. Unplug chain saw from power source

• When not in use

• Before moving from one place to another

Electric Chain Saw EN

• Before servicing

• Before changing accessories or

attachments, such as saw chain and guard

2. Inspect chain saw before and after each

use. Check saw closely if guard or other

part has been damaged. Check for any

damage that may affect operator safety or

operation of saw. Check for alignment or

binding of moving parts. Check for broken

or damaged parts. Do not use chain saw if

damage affects safety or operation. Have

damage repaired by authorized service

center. To locate an authorized service center,

visit www.worx.com

3. Maintain chain saw with care.

• Never expose saw to rain or direct

moisture.

• Keep chain sharp, clean, and lubricated for

better and safer performance.

• Follow steps outlined in this manual to

sharpen chain.

• Keep handles dry, clean, and free of oil and

grease.

• Keep all screws and nuts tight.

• Inspect power cord often. If damaged,

have repaired by authorized service center.

• Never carry chain saw by power cord.

• Never yank power cord to unplug it.

• Keep power cord from heat, oil, and sharp

edges.

• Inspect extension cords often and replace

if damaged.

4. When servicing, use only identical

replacement parts.

5. When not in use, always store chain saw

• In a high or locked place, out of children’s

reach

• In a dry place

• With Bar and Chain Storage Cover (21) in

place

Bar Maintenance

To maximize bar life, the following bar

maintenance is recommended.

The bar rails that carry the chain should be

cleaned before storing the tool or if the bar or

chain appear to be dirty.

The rails should be cleaned every time the

chain is removed.

To clean the Bar rails:

1. Remove chain cover and bar and chain.

(see section ASSEMBLY)

2. Using a wire brush, screwdriver or similar

tool, clear the residue from the inner

groove of the bar. (See Fig. M)

3. Make sure to clean oil passages thoroughly

Conditions which require Chain (10) and

Guide Bar (9) maintenance:

• Saw cuts to one side or at an angle.

• Saw has to be forced through the cut.

• Inadequate supply of oil to the bar and chain.

Check the condition of the Guide Bar each

time the chain is sharpened. A worn Guide

Bar will damage the chain and make cutting

difﬁcult.

After each use, with unit disconnected from

power source, clean all sawdust from the

Guide Bar and sprocket hole.

When rail top is uneven, use a ﬂat ﬁle to

restore square edges and sides.

File Rail Edges

and Sides

Square

Worn Groove Correct Groove

Replace the Guide Bar when the groove is

worn, the Guide Bar is bent or cracked, or

when excess heating or burring of the rails

occurs. If replacement is necessary, use only

the Guide Bar speciﬁed for your saw in the

repair parts list or on the decal located

on the chain saw.

Replacing Bar & Chain

Replace chain when cutters are too worn

to sharpen or when chain stops. Only use

replacement chain noted in this manual.

Inspect Guide Bar before sharpening chain.

A worn or damaged Guide Bar is unsafe. A

worn or damaged Guide Bar will damage

chain. It will also make cutting harder.

Turn the bar over, top rail becoming bottom

and bottom rail becoming top, around every 5

hours of use. Fit the Bar Tensioning Plate (22)

Tab into the new bar by tightening the screw

clockwise. The tab protrusion (a) must be

ﬁtted into the bar hole. (See Fig. N)

Electric Chain Saw EN

Sharpening Saw Chain

WARNING: Unplug chain saw from

power source before servicing.

Severe injury or death could occur from

electrical shock or body contact with

moving chain.

Cutting edges on chain are sharp. Use

protective gloves when handling chain.

Keep chain sharp. Your saw will cut faster and

more safely. A dull chain will cause undue

sprocket, Guide Bar, chain, and motor wear.

If you must force chain into wood and cutting

creates only sawdust with few large chips,

chain is dull.

Lubricate Sprocket

WARNING: Wear heavy duty gloves

when performing any maintenance or

service to this tool.

Always unplug the tool before performing any

service or maintenance on this tool.

NOTE: It is not necessary to remove the chain

or bar when lubricating the guide bar sprocket

1. Clean the bar and sprocket

2. Using a grease gun, insert the tip of the

gun into the lubrication hole and inject

grease until it appears at the outside edge

of the sprocket tip. (See Fig.O )

3. To rotate the sprocket pull the chain by

hand until the ungreased side of the

sprocket is in line with the grease hole.

Repeat the lubrication procedure.

TROUBLESHOOTING TABLE

The following table gives checks and actions that you can perform if your machine does not

operate correctly. If these do not identify/remedy the problem, contact your service agent.

WARNING: Switch off and remove plug from power source before investigating

fault.

Symptom Possible Cause Remedy

Chain saw fails to

operate

No power

Power source socket faulty

Extension cord damaged

Check power

Use another socket

Check cord, replace

Chain saw

operates

intermittently

Extension cord damaged

Loose connection

Internal wiring defective

On/Off switch defective

Check cord, replace

Contact service agent 1-866-354-

WORX (9679)

Contact service agent 1-866-354-

WORX (9679)

Contact service agent 1-866-354-

WORX (9679)

Dry chain No oil in reservoir

Vent in oil ﬁller cap clogged

Oil passage clogged

Reﬁll oil

Clean cap

Clean oil passage outlet

Chain/chain bar

over-heats

No oil in reservoir

Vent in oil ﬁller cap clogged

Oil passage clogged

Chain is over tensioned

Dull chain

Reﬁll oil

Clean cap

Clean oil passage outlet

Adjust chain tension

Sharpen chain or replace

Chain saw rips,

vibrates, does not

saw properly

Chain tension too loose

Dull chain

Chain worn out

Chain teeth are facing in the wrong

direction

Adjust chain tension

Sharpen chain or replace

Replace chain

Reassemble with chain in correct

direction

1918

Tronçonneuse électrique prime F

SÉCURITÉ DU PRODUIT

AVERTISSEMENT! Certaines des

poussières produites en utilisant

des outils électriques sont considérées

par l’État de Californie comme

susceptibles de provoquer le cancer,

des anomalies congénitales et d’autres

problèmes de reproduction. Voici des

exemples de ces produits chimiques:

• Plomb issu de peinture à base de

plomb

• Silice crystalline issue de briques

et du ciment et autres produits de

maçonnerie

• Arsenic et chrome issus de bois traité

chimiquement

Votre risque de ces expositions varie en

fonction de la fréquence à laquelle vous

effectuez ce travail. Pour réduire votre

exposition à ces produits chimiques:

• Travaillez dans une zone bien ventilée;

• Portez un équipement de sécurité

approuvé, tel que des masques

antipoussières spécialement

conçus pour éliminer les particules

microscopiques par filtrage.

AVERTISSEMENT : Ce produit

peut vous exposer à des produits

chimiques, incluant au plomb, au

phtalate ou au bisphénol A, qui sont

reconnus dans l’État de Californie

comme pouvant causer un cancer, des

anomalies congénitales ou d’autres

dommages à l’appareil reproducteur.

Assurez-vous de bien vous laver les

mains après usage. Pour en savoir

plus, veuillez consulter le site www.

P65Warnings.ca.gov.

AVERTISSEMENTS

GENERAUX CONCERNANT

LA SECURITE DES OUTILS

ELECTRIQUES

AVERTISSEMENT! Lisez et

assimilez toutes les instructions.

Le non-respect des instructions ci-après

peut entraîner un risque de choc électrique,

d’incendie et/ou de blessures graves.

Conservez tous les avertissements et

instructions pour pouvoir les consulter

ultérieurement.

L’expression « outil électrique » dans tous

les avertissements énumérés ci-dessous se

réfère à votre outil électrique fonctionnant sur

secteur (branché) ou à batterie (sans-ﬁl).

1. AIRE DE TRAVAIL

a) Veillez à ce que l’aire de travail soit

propre et bien éclairée. Le désordre

et le manque de lumière favorisent les

accidents.

b) N’utilisez pas d’outils électriques

dans un milieu présentant un risque

d’explosion, par exemple en présence

de liquides, de gaz ou de poussières

inﬂammables. Les outils électriques

créent des étincelles qui pourraient

enﬂammer les poussières ou les vapeurs.

c) Gardez à distance les curieux, les

enfants et les visiteurs lorsque vous

travaillez avec un outil électrique. Ils

pourraient vous distraire et vous faire faire

une fausse manoeuvre.

2. SÉCURITÉ ÉLECTRIQUE

a) Les ﬁches des outils électriques

doivent correspondre aux prises

murales. Ne jamais modiﬁer la ﬁche

de quelque façon que ce soit. Ne

pas utiliser de ﬁches d’adaptation

avec des outils électriques mis à

la terre (mis à la masse). Des ﬁches

non modiﬁées et des prises qui leur

correspondent réduiront le risque de choc

électrique.

b) Évitez tout contact corporel avec des

surfaces mises à la terre (tuyauterie,

radiateurs, cuisinières, réfrigérateurs,

etc.). Le risque de choc électrique est plus

grand si votre corps est en contact avec la

terre.

c) N’exposez pas les outils électriques

à la pluie ou à l’eau. La présence d’eau

dans un outil électrique augmente le

risque de choc électrique.

d) Ne maltraitez pas le cordon. Ne

transportez jamais l’outil par son

cordon et ne débranchez jamais

1918

Tronçonneuse électrique prime F

la ﬁche en tirant sur le cordon.

N’exposez pas le cordon à la chaleur,

à des huiles, à des arrêtes vives ou à

des pièces en mouvement. Un cordon

endommagé augmente le risque de choc

électrique.

e) Lorsque vous utilisez un outil

électrique à l’extérieur, utilisez un

prolongateur adapté à une utilisation

en extérieur. L’utilisation d’un cordon

adapté à une utilisation extérieure réduit le

risque de choc électrique.

f) Si vous devez utiliser un outil

électrique dans un endroit humide,

utilisez un dispositif de courant

résiduel (RCD) d’alimentation

protégée. L’utilisation d’un RCD réduit le

risque de choc électrique.

3. SÉCURITÉ DES PERSONNES

a) Restez alerte, concentrez-vous sur

votre travail et faites preuve de bon

sens. N’utilisez pas un outil électrique

si vous êtes fatigué ou sous

l’inﬂuence de drogues, d’alcool ou de

médicaments. Un instant d’inattention

lors de l’utilisation d’outils électriques peut

entraîner des blessures graves.

b) Utilisez des accessoires de sécurité.

Portez toujours une protection

oculaire. De l’équipement de sécurité

tel que le masque antipoussière, les

chaussures de sécurité antidérapantes, des

casques durs ou des protections antibruit

utilisés dans des conditions appropriées

réduiront les blessures corporelles.

c) Évitez les démarrages accidentels.

Avant d’insérer la batterie dans l’outil,

assurez-vous que son interrupteur

est en position « OFF » (Arrêt) ou

verrouillée. Le fait de transporter un outil

avec le doigt sur la détente/l’interrupteur

ou d’insérer la batterie dans un outil dont

la détente est en position « ON » (Marche)

peut causer un accident.

d) Retirer les clés de réglage avant de

mettre l’outil sous tension. Une clé

restée attachée à une partie mobile de

l’outil pourrait entraîner des blessures

corporelles.

e) Ne vous penchez pas trop en avant.

Maintenez un bon appui et restez en

équilibre en tout temps. Une bonne

stabilité vous permet de mieux réagir à une

situation inattendue.

f) Habillez-vous convenablement.

Ne portez ni vêtements ﬂottants

ni bijoux. Gardez les cheveux, les

vêtements et les gants éloignés des

pièces en mouvement. Les vêtements

ﬂottants, les bijoux ou les cheveux longs

risquent d’être happés par des pièces en

mouvement.

g) Si un sac de récupération de

la poussière est fourni avec un

connecteur pour aspirateur, assurez

vous qu’il est correctement relié et

utilisé de façon appropriée. L’utilisation

de ce système réduit les dangers physiques

et physiologiques liés à la poussière.

4. UTILISATION ET ENTRETIEN DE

L’OUTIL

a) Ne forcez pas l’outil. Utilisez l’outil

approprié à la tâche. L’outil approprié

fonctionne mieux et de façon plus

sécuritaire. Respectez aussi la vitesse de

travail qui lui est propre.

b) N’utilisez pas un outil si l’interrupteur

ne le met pas en marche ou ne peut

l’arrêter. Un outil qui ne peut être contrôlé

par l’interrupteur est dangereux et doit être

réparé.

c) Débranchez la batterie de l’outil ou

mettez son interrupteur en position

« OFF » (Arrêt) ou « LOCKED »

(Verrouillé) avant d’effectuer un

réglage, de changer d’accessoire ou

de ranger l’outil. De telles mesures de

sécurité préventive réduisent le risque de

démarrage accidentel de l’outil.

d) Rangez les outils hors de portée

des enfants et d’autres personnes

inexpérimentées. Les outils sont

dangereux dans les mains d’utilisateurs

novices.

e) Prenez soin de bien entretenir

les outils. Soyez attentif à tout

désalignement ou coincement des

pièces en mouvement, à tout bris ou

2120

Tronçonneuse électrique prime F

à toute autre condition préjudiciable

au bon fonctionnement de l’outil. Si

vous constatez qu’un outil est endommagé,

faites-le réparer avant de vous en servir. De

nombreux accidents sont causés par des

outils en mauvais état.

f) Les outils de coupe doivent être

toujours bien affûtés et propres. Des

outils bien entretenus, dont les arêtes sont

bien tranchantes, sont moins susceptibles

de se coincer et plus faciles à contrôler.

g) Utilisez l’outil électrique, les

accessoires et les forets etc., en

conformité avec ces instructions et

de la manière conçue pour le type

particulier d’outil électrique, prend en

compte les conditions de travail et le

travail qui doit être accompli. L’emploi

de l’outil électrique pour des opérations

différentes de celles pour lesquelles il a

été conçu pourrait entraîner une situation

dangereuse.

5. ENTRETIEN

a) Ayez votre outil électrique entretenu

par un réparateur agréé n’utilisant que

des pièces de rechange identiques.

Cela assurera que la sécurité de l’outil

électrique est maintenue.

CONSIGNES DE SÉCURITÉ

POUR LA SCIE À CHAÎNE

1. Tenez la scie à chaîne bien éloignée

des parties de votre corps lorsque

celle-ci est en marche. Avant de

mettre en marche la scie à chaîne,

veillez à ce qu’elle ne soit en contact

avec aucun objet. Vos vêtements

peuvent s’accrocher à la scie à chaîne

ou alors votre corps peut s’y coller

pendant un moment d’inattention lors du

fonctionnement du matériel.

2. Toujours tenir la poignée arrière de la

scie à chaîne avec votre main droite

et la poignée avant avec votre main

gauche. Évitez d’inverser la position des

mains, car ceci pourrait augmenter le risque

de blessure et ne doit jamais être fait.

3. Tenez l’outil électrique par ses

surfaces de prise isolées uniquement,

car la chaîne de la scie peut entrer

en contact avec un câblage dissimulé

ou son propre câble. Les chaînes de la

scie qui entrent en contact avec un câble

conducteur peuvent rendre conducteurs

les pièces en métal de l’outil électrique

et causer ainsi un choc électrique à

l’opérateur.

4. Portez des lunettes de sécurité et des

protège-oreilles. Des équipements

de protection supplémentaires pour

la tête, les mains, les jambes et les

pieds sont recommandés. Portez des

vêtements de protection adaptés aﬁn

de réduire les risques de blessure par

des débris volants ou d’éviter un contact

accidentel avec la chaîne de scie.

5. Évitez de faire fonctionner la scie à

chaîne lorsque vous vous trouvez

sur un arbre. Faire fonctionner une scie

à chaîne tout en haut d’un arbre peut

entraîner des blessures.

6. Gardez toujours une bonne assise et

ne faites fonctionner la scie à chaîne

que lorsque vous êtes debout sur une

surface ﬁxe, sécurisée et plane. Les

surfaces glissantes ou instables telles que

les échelles peuvent entraîner une perte

d’équilibre ou de contrôle de la scie à

chaîne.

7. Lors de la coupe d’une branche sous

tension, faites attention au retour de

celle-ci. Lorsque la tension des ﬁbres de

bois est relâchée, la branche semblable à

un ressort peut frapper l’opérateur et/ou

rendre la scie à chaîne incontrôlable.

8. Soyez extrêmement prudent lors de la

coupe de la broussaille et des jeunes

arbres. Le matériau ﬁn peut être pris dans

la chaîne et vous frapper ou vous faire

perdre l’équilibre.

9. Portez la scie à chaîne par la poignée

avant lorsqu’elle est en arrêt, et

éloignez-la de votre corps. Lors du

transport ou du stockage de la scie à

chaîne, toujours rabattre le protecteur de

guide-chaîne. Une manipulation appropriée

de la scie à chaîne permettra de réduire la

La page charge ...

Worx WG305.1 Le manuel du propriétaire

Marque: Worx

Modèle: WG305.1

Catégorie: Tronçonneuses électriques

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Worx WG305.1 Owner's manual
español: Worx WG305.1 El manual del propietario

Worx WG305.1 Le manuel du propriétaire

Worx WG305.1 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents