Simplicity 020323-0 Manuel utilisateur

Marque: Simplicity

Modèle: 020323-0

Catégorie: Nettoyeurs haute pression

Taper: Manuel utilisateur

2550 PSI MAX

2.3 GPM MAX

PRESSURE WASHER

CLEANING SYSTEM

Operator’s Manual

Model No. 580.676630

Part No. 203800GS Draft - (07/26/2007)

• Safety

• Assembly

• Operation

• Maintenance

• Parts

• Français, p. 34

HOURS: Mon. - Fri. 8 a.m. to 5 p.m. (CT)

PRESSURE WASHER

CUSTOMER HELPLINE

1-800-222-3136

Sears Canada, Inc.

Visit our Craftsman website: www.sears.ca

AVERTISSEMENT

Avant d’utiliser ce produit, veuillez lire le

manuel et suivre toutes les directives

relatives à la sécurité et à l’utilisation.

WARNING

Before using this product, read this

manual and follow all Safety Rules

and Operating Instructions.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages

that follow this symbol to avoid possible injury or death.

Read this manual carefully and become familiar

with your pressure washer. Know its applications,

its limitations, and any hazards involved.

The safety alert symbol ( ) is used with a signal word

(DANGER, CAUTION, WARNING), a pictorial and/or a safety

message to alert you to hazards. DANGER indicates a hazard

which, if not avoided, will result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury. CAUTION indicates a hazard

which, if not avoided, might result in minor or moderate

injury. NOTICE indicates a situation that could result in

equipment damage. Follow safety messages to avoid or

reduce the risk of injury or death.

Hazard Symbols and Meanings

SAFETY RULES

WARRANTY

TABLE OF CONTENTS

ONE-YEAR FULL WARRANTY ON CRAFTSMAN PRESSURE WASHER

If this pressure washer fails due to a defect in material or workmanship within one year from the date of purchase, return it to

any Sears store, other Craftsman outlet, or Sears Parts & Repair Center in the United States or Canada for free repair (or

replacement if repair proves impossible).

All warranty coverage applies for only 90 days from date of purchase if this pressure washer is ever used for commercial or

rental purposes.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., Hoffman Estates, IL 60179

Sears Canada Inc., Toronto, Ontario, Canada M5B 2B8

WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

FEATURES AND CONTROLS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10

OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-14

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-20

STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-31

EMISSION CONTROL WARRANTY . . . . . . . . . . . . . . . . . . . . . 32-33

FRANÇAIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34-59

HOW TO ORDER PARTS . . . . . . . . . . . . . . . . . . . . . . . . BACK PAGE

Fire

Explosion

Toxic Fumes

Hot Surface

Moving Parts

Electrical Shock

Slippery Surface

Fall

Kickback

Flying Objects

Fluid Injection

Operator’s Manual

WARNING

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

WARNING

Running engine gives off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide can cause headache,

fatigue, dizziness, vomiting, confusion, seizures,

nausea, fainting or death.

Some chemicals or detergents may be harmful if

inhaled or ingested, causing severe nausea,

fainting, or poisoning.

• Operate pressure washer ONLY outdoors.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes, or other openings.

• DO NOT start or run engine indoors or in an enclosed area,

even if windows and doors are open.

• Use a respirator or mask whenever there is a chance that

vapors may be inhaled.

• Read all instructions with mask so you are certain the mask will

provide the necessary protection against inhaling harmful

vapors.

WARNING

Risk of electrocution.

Contact with power source can cause electric

shock or burn.

• NEVER spray near power source.

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WHEN ADDING OR DRAINING FUEL

• Turn pressure washer OFF and let it cool at least 2 minutes

before removing fuel cap. Loosen cap slowly to relieve pressure

in tank.

• Fill or drain fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

WHEN STARTING EQUIPMENT

• Ensure spark plug, muffler, fuel cap, and air cleaner are in

place.

• DO NOT crank engine with spark plug removed.

WHEN OPERATING EQUIPMENT

• DO NOT tip engine or equipment at angle which causes fuel to

spill.

• DO NOT spray flammable liquids.

WHEN TRANSPORTING OR REPAIRING EQUIPMENT

• Transport/repair with fuel tank EMPTY or with fuel shutoff valve

OFF.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers, or other appliances that have pilot light or other ignition

source because they can ignite fuel vapors.

WARNING

Use of pressure washer can create puddles and

slippery surfaces.

Kickback from spray gun can cause you to fall.

• Operate pressure washer from a stable surface.

• The cleaning area should have adequate slopes and drainage to

reduce the possibility of a fall due to slippery surfaces.

• Be extremely careful if you must use the pressure washer from

a ladder, scaffolding, or any other similar location.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

WARNING

Starter cord kickback (rapid retraction) can result

in bodily injury. Kickback will pull hand and arm

toward engine faster than you can let go.

Broken bones, fractures, bruises, or sprains

could result.

• NEVER pull starter cord without first relieving spray gun

pressure.

• When starting engine, pull cord slowly until resistance is felt

and then pull rapidly to avoid kickback.

• After each starting attempt, where engine fails to run, always

point spray gun in safe direction and squeeze spray gun trigger

to release high pressure. Engage spray gun trigger lock.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

WARNING

Contact with muffler area can result in serious

burns.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (1.5 m) of clearance on all sides of

pressure washer including overhead.

• Code of Federal Regulation (CFR) Title 36 Parks, Forests, and

Public Property require equipment powered by an internal

combustion engine to have a spark arrester, maintained in

effective working order, complying to USDA Forest service

standard 5100-1C or later revision. In the State of California a

spark arrester is required under section 4442 of the California

Public resources code. Other states may have similar laws.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected,

which can cause injury.

• DO NOT allow CHILDREN to operate pressure washer.

• NEVER repair high pressure hose. Replace it.

• NEVER repair leaking connections with sealant of any kind.

Replace o-ring or seal.

• NEVER connect high pressure hose to nozzle extension.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction and squeeze spray

gun trigger, to release high pressure, every time you stop

engine. Engage trigger lock when not in use.

• NEVER aim spray gun at people, animals, or plants.

• DO NOT secure spray gun in open position.

• DO NOT leave spray gun unattended while machine is running.

• NEVER use a spray gun which does not have a trigger lock or

trigger guard in place and in working order.

• Always be certain spray gun, nozzles and accessories are

correctly attached.

WARNING

Unintentional sparking can result in fire or

electric shock.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

PRESSURE WASHER

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

WARNING

Risk of eye injury.

Spray can splash back or propel objects.

• Always wear safety goggles when using this equipment or in

vicinity of where equipment is in use.

• Before starting the pressure washer, be sure you are wearing

adequate safety goggles.

• NEVER substitute safety glasses for safety goggles.

WARNING

Starter and other rotating parts can entangle

hands, hair, clothing, or accessories.

• NEVER operate pressure washer without protective housing or

covers.

• DO NOT wear loose clothing, jewelry or anything that may be

caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

NOTICE

High pressure spray may damage fragile items including

glass.

• DO NOT point spray gun at glass when using red (0°) spray tip.

• NEVER aim spray gun at plants.

NOTICE

Improper treatment of pressure washer can damage it and

shorten its life.

• If you have questions about intended use, ask dealer or contact

Sears.

• NEVER operate units with broken or missing parts, or without

protective housing or covers.

• DO NOT by-pass any safety device on this machine.

• DO NOT tamper with governed speed.

• DO NOT operate pressure washer above rated pressure.

• DO NOT modify pressure washer in any way.

• Before starting pressure washer in cold weather, check all parts

of the equipment to be sure ice has not formed there.

• NEVER move machine by pulling on hoses. Use handle

provided on unit.

• Check fuel system for leaks or signs of deterioration, such as

chafed or spongy hose, loose or missing clamps, or damaged

tank or cap. Correct all defects before operating pressure

washer.

• This equipment is designed to be used with Sears authorized

parts ONLY. If equipment is used with parts that DO NOT

comply with minimum specifications, user assumes all risks

and liabilities.

KNOW YOUR PRESSURE WASHER

Read the Operator’s Manual and safety rules before operating your pressure washer.

Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls and

adjustments. Save this manual for future reference.

FEATURES AND CONTROLS

A - Spray Gun — Controls the application of water onto

cleaning surface with trigger device. Includes trigger lock.

B - Cleaning Tank – Used to provide pressure washer safe

detergents into the low pressure stream.

C - Spray Tips — Detergent, 0°, 15° and 40°: for various

high pressure cleaning applications.

D - Recoil Starter — Used for starting the engine manually.

E - Fuel Tank — Fill tank with regular unleaded fuel. Always

leave room for fuel expansion.

F - Throttle Lever — Sets engine in starting mode for recoil

starter and stops a running engine.

G - Air Filter — Protects engine by filtering dust and debris

out of intake air.

H - Pump — Develops high pressure.

J - Automatic Cool Down System — Cycles water through

pump when water reaches 125°-155°F. Warm water will

discharge from pump onto ground. This system prevents

internal pump damage.

K - High Pressure Outlet — Connection for high pressure

hose.

L - Water Inlet — Connection for garden hose.

M - Oil Fill/Dipstick — Check, add and drain engine oil here.

N - High Pressure Hose — Connect one end to water pump

and the other end to spray gun.

Items Not Shown:

Data Tag (near rear of base plate) — Provides model and

serial number of pressure washer. Please have these readily

available if calling for assistance.

Nozzle Extension with Quick Connect — Allows you to

switch between four different spray tips.

Safety Goggles — Always use the enclosed safety goggles

when running your pressure washer.

Warning/Operating Instructions Tag — Identifies hazards

and proper procedure to start/stop pressure washer.

Your cleaning system requires some assembly and is ready

for use only after it has been properly serviced with the

recommended oil and fuel.

If you have any problems with the assembly of your

pressure washer, please call the pressure washer helpline

at 1-800-222-3136.

UNPACK THE PRESSURE WASHER

1. Remove everything from carton except pressure washer.

2. Open carton completely by cutting each corner from top

to bottom.

3. Remove pressure washer from carton.

CARTON CONTENTS

Check all contents. If any parts are missing or damaged, call

the pressure washer helpline at 1-800-222-3136.

• Main Unit

• Handle

• Cleaning Tank Assembly

• High Pressure Hose

• Spray Gun

• Nozzle Extension with Quick Connect Fitting and Nozzle

Holder

• Oil Bottle

• Detergent Siphoning Hose/Filter

• Parts Bag (which includes the following):

• Operator’s Manual

• Safety Goggles

• Gun Holder Wireform

• Bag containing 4 multi–colored Spray Tips

• Handle Fastening Hardware Kit (which includes):

• Carriage Bolts (2)

• “L” Bolt

• Plastic Knobs (4)

• Tree Clips (4)

Become familiar with each piece before assembling the

pressure washer. Identify all contents with the illustration on

page 6. If any parts are missing or damaged, call the

pressure washer helpline at 1-800-222-3136.

ASSEMBLING CLEANING SYSTEM

Your Craftsman cleaning system will need assembly before

operation:

1. Attach handle and cleaning tank.

2. Connect detergent siphon hose to pump.

3. Add oil to engine crankcase.

4. Add fuel to fuel tank.

5. Connect pressure hose to spray gun and pump.

6. Connect water supply to pump.

7. Attach nozzle extension to spray gun.

8. Select/attach quick connect spray tip to nozzle extension.

Attach Handle and Cleaning Tank

1. Place handle (A) onto handle supports (B) connected to

main unit. Make sure holes (C) in handle align with holes

NOTE: It may be necessary to move the handle supports

from side to side in order to align the handle so it will slide

over the handle supports.

2. Insert carriage bolts (A) through holes from back of unit

and attach a plastic knob (B) from front of unit. Tighten

by hand.

3. Place cleaning tank (B) over holes (C) on handle

(viewing from front of unit). Push the tree clips (A) into

the holes until they sit flat against the cleaning tank.

4. Insert “L” bolt (A) through hole just above cleaning tank

on right side of handle (viewing from front of unit). Hold

bolt in place and attach plastic knob (B) from inside of

unit. Tighten by hand.

ASSEMBLY

5. Insert spray gun holder wireform (A) through hole just

above cleaning tank on left side of handle (viewing from

front of unit). Hold wireform in place and attach a plastic

knob (B) from inside of unit. Tighten by hand.

Attach Detergent Siphon Hose to Pump

The pressure washer is equipped with two detergent

siphoning hoses. One is attached to the cleaning tank and

one is loose for siphoning pressure washer safe detergents

from a bottle or container.

Attach one of the detergent siphon hoses (A) to the barbed

hose fitting (B) on the pump.

IMPORTANT: Only one detergent siphoning hose can be used

at a time. When cleaning tank is not used, make sure

detergent shut-off valve on cleaning tank is in the “Off”

position.

Add Engine Oil

1. Place pressure washer on a flat, level surface.

2. Clean area around oil fill and remove yellow oil fill

cap/dipstick.

NOTE: See Oil Recommendations in Maintenance section.

Verify provided oil bottle is the correct viscosity for current

ambient temperature.

3. Using oil funnel (optional), slowly pour contents of

provided oil bottle into oil fill opening.

4. Replace oil fill cap/dipstick and fully tighten.

Add Fuel

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). High altitude

use, see High Altitude.

• Gasoline with up to 10% ethanol (gasohol) or up to 15%

MTBE (methyl tertiary butyl ether) is acceptable.

To protect the fuel system from gum formation, mix in a fuel

stabilizer when adding fuel. See Storage. All fuel is not the

same. If you experience starting or performance problems

after using fuel, switch to a different fuel provider or change

brands. This engine is certified to operate on gasoline. The

emission control system for this engine is EM (Engine

Modifications).

1. Clean area around fuel fill cap, remove cap.

2. Slowly add regular unleaded fuel (A) to fuel tank (B). Be

careful not to overfill. Allow about 1.5" (4 cm) (C) of tank

space for fuel expansion.

3. Install fuel cap and wait for any spilled fuel to evaporate.

NOTICE

Improper treatment of pressure washer can damage it and

shorten its life.

• DO NOT attempt to crank or start the engine before it has been

properly serviced with the recommended oil. This may result in

an engine failure.

NOTICE

Avoid pressure washer damage.

Failure to follow Operator’s Manual for fuel

recommendations voids warranty.

• DO NOT use unapproved gasoline such as E85.

• DO NOT mix oil in gasoline.

• DO NOT modify engine to run on alternate fuels.

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WHEN ADDING FUEL

• Turn pressure washer OFF and let it cool at least 2 minutes

before removing fuel cap. Loosen cap slowly to relieve pressure

in tank.

• Fill fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

CAUTION! Alcohol-blended fuels (called gasohol, ethanol or

methanol) can attract moisture, which leads to separation and

formation of acids during storage. Acidic gas can damage the

fuel system of an engine while in storage.

To avoid engine problems, the fuel system should be treated

with a fuel preserver or emptied before storage of 30 days or

longer. If adding a fuel preserver, fill the fuel tank with fresh

fuel. If only partially filled, air in the tank will promote fuel

deterioration during storage. If fuel preserver is not used,

drain the fuel tank, start the engine and let it run until the fuel

lines and carburetor are empty. Use fresh fuel next season.

See Storage for additional information.

NEVER use engine or carburetor cleaner products in the fuel

tank as permanent damage may occur.

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum

85 octane / 85 AKI (89 RON) gasoline is acceptable. To

remain emissions compliant, high altitude adjustment is

required. Operation without this adjustment will cause

decreased performance, increased fuel consumption, and

increased emissions. See a qualified Sears dealer for high

altitude adjustment information. Operation of the engine at

altitudes below 2,500 feet (762 meters) with the high altitude

kit is not recommended.

Connect Hose and Water Supply to Pump

NOTE: Remove and discard the shipping caps from the

pump’s high pressure outlet and water inlet before attaching

hoses.

1. Uncoil high pressure hose and attach one end of hose to

base of spray gun. Tighten by hand.

2. Attach other end of high pressure hose to high pressure

outlet on pump. Tighten by hand.

NOTICE

DO NOT run the pump without the water supply connected

and turned on.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

• NEVER connect high pressure hose to nozzle extension.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• Always be certain spray gun, nozzles and accessories are

correctly attached.

3. Before connecting garden hose to water inlet, inspect

inlet screen (A). Clean screen if it contains debris or have

it replaced if damaged. DO NOT run pressure washer if

inlet screen is damaged or missing.

4. Run water through garden hose for 30 seconds to flush

it of debris. Turn off water.

IMPORTANT: DO NOT siphon standing water for the water

supply. Use ONLY cold water (less than 100°F (38°C)).

5. Connect garden hose (not to exceed 50 feet (15.24 m) in

length) to water inlet. Tighten by hand.

6. Turn ON water, point gun in a safe direction and squeeze

trigger to purge pump system of air and impurities.

Checklist Before Starting Engine

Review the unit to ensure you have performed all of the

following:

1. Be sure to read Safety Rules and Operation sections

before using the cleaning system.

2. Make sure handle is in place and secure.

3. Check that oil has been added to proper level in engine

crankcase.

4. Add proper fuel to fuel tank.

5. Check for proper hose connections (high pressure and

water supply) and that there are no kinks, cuts, or

damage to the high pressure hose.

6. Provide proper water supply (not to exceed 100°F

(38°C)).

NOTICE

Using a One Way Valve (vacuum breaker or check valve) at

pump inlet can cause pump or inlet connector damage.

• There MUST be at least ten feet of unrestricted garden hose

between the pressure washer inlet and any device, such as a

vacuum breaker or check valve.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

WARNING

Risk of eye injury.

Spray can splash back or propel objects.

• Always wear safety goggles when using this equipment or in

vicinity of where equipment is in use.

• Before starting the pressure washer, be sure you are wearing

adequate safety goggles.

• NEVER substitute safety glasses for safety goggles.

HOW TO USE YOUR CLEANING SYSTEM

If you have any problems operating your pressure washer,

please call the pressure washer helpline at 1-800-222-3136.

Pressure Washer Location

Pressure Washer Clearance

Place pressure washer outdoors in an area that will not

accumulate deadly exhaust gas. DO NOT place pressure

washer where exhaust gas (A) could accumulate and enter

inside or be drawn into a potentially occupied building.

Ensure exhaust gas is kept away from any windows, doors,

ventilation intakes, or other openings that can allow exhaust

gas to collect in a confined area. Prevailing winds and air

currents should be taken into consideration when positioning

pressure washer.

To Start Your Cleaning System

To start your engine-powered cleaning system for the first

time, follow these instructions step-by-step. This information

also applies whenever you start the engine after you have let

the pressure washer sit idle for at least a day.

1. Place pressure washer outside near an water source

capable of supplying water at a flow rate greater than

3.3 gallons (12.5 l) per minute and no less than 20 PSI

(1.38 BARS) at pressure washer end of garden hose.

2. Check that high pressure hose is tightly connected to

spray gun and pump. See Assemby for illustrations.

3. Make sure unit is in a level position.

4. Connect garden hose to water inlet on pressure washer

pump.

5. Turn ON water, point gun in a safe direction and squeeze

trigger to purge pump system of air and impurities.

6. Place colored quick connect spray tips in slots on holder

that’s attached to nozzle extension.

7. Attach nozzle extension to spray gun. Tighten by hand.

8. Choose spray tip you want to use and insert it into

nozzle extension. See How to Use Spray Tips.

9. Engage trigger lock (A) on spray gun trigger.

OPERATION

WARNING

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

• Keep at least 5 ft. (152 cm) clearance on all sides of pressure

washer including overhead.

WARNING

Running engine gives off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide can cause headache,

fatigue, dizziness, vomiting, confusion, seizures,

nausea, fainting or death.

• Operate pressure washer ONLY outdoors.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes, or other openings.

• DO NOT start or run engine indoors or in an enclosed area,

even if windows and doors are open.

NOTICE

DO NOT run the pump without the water supply connected

and turned on.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

10. Move throttle lever to “Fast” position (A), shown as a

rabbit.

IMPORTANT: Before starting the pressure washer, be sure

you are wearing adequate safety goggles.

NOTE: This unit is equipped with a ReadyStart™ engine. A

ReadyStart™ engine means there is no priming or choking

required.

11. When starting engine, position yourself as

recommended and grasp starter grip handle and pull

slowly until you feel some resistance. Then pull rapidly

to start engine.

12. Return recoil starter slowly. DO NOT let rope “snap

back” against starter.

NOTE: Always keep the throttle lever in the “Fast” position

when operating the pressure washer.

WARNING

Starter cord kickback (rapid retraction) can result

in bodily injury. Kickback will pull hand and arm

toward engine faster than you can let go.

Broken bones, fractures, bruises, or sprains

could result.

• NEVER pull starter cord without first relieving spray gun

pressure.

• When starting engine, pull cord slowly until resistance is felt

and then pull rapidly to avoid kickback.

• After each starting attempt, where engine fails to run, always

point spray gun in safe direction and squeeze spray gun trigger

to release high pressure. Engage spray gun trigger lock.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

WARNING

Contact with muffler area can result in serious

burns.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (1.5 m) of clearance on all sides of

pressure washer including overhead.

• Code of Federal Regulation (CFR) Title 36 Parks, Forests, and

Public Property require equipment powered by an internal

combustion engine to have a spark arrester, maintained in

effective working order, complying to USDA Forest service

standard 5100-1C or later revision. In the State of California a

spark arrester is required under section 4442 of the California

Public resources code. Other states may have similar laws.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected,

which can cause injury.

• DO NOT allow CHILDREN to operate pressure washer.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• NEVER aim spray gun at people, animals, or plants.

• DO NOT secure spray gun in open position.

• DO NOT leave spray gun unattended while machine is running.

• NEVER use a spray gun which does not have a trigger lock or

trigger guard in place and in working order.

• Always be certain spray gun, nozzles and accessories are

correctly attached.

WARNING

Risk of eye injury.

Spray can splash back or propel objects.

• Always wear safety goggles when using this equipment or in

vicinity of where equipment is in use.

• Before starting the pressure washer, be sure you are wearing

adequate safety goggles.

• NEVER substitute safety glasses for safety goggles.

How to Stop Your Cleaning System

1. Release spray gun trigger and let engine idle for two

minutes.

2. Move throttle to SLOW position, then STOP position (A).

3. ALWAYS point spray gun in a safe direction and squeeze

spray gun trigger to release retained high water

pressure.

IMPORTANT: Spray gun traps high water pressure, even

when engine is stopped and water is disconnected.

4. Engage trigger lock on spray gun when not in use.

How to Use Spray Tips

The quick–connect on the nozzle extension allows you to

switch between four different quick connect spray tips. Spray

tips can be changed while pressure washer is running once

spray gun trigger lock is engaged. The spray tips vary the

spray pattern as shown below.

Follow these instructions to change spray tips:

1. Engage trigger lock on spray gun.

2. Pull back collar on quick–connect and pull current spray

tip off. Store spray tips in holder provided on the nozzle

extension.

3. Select desired spray tip:

• For delicate rinse (lower pressure and higher flow),

for gentle cleaning of cars/trucks, boats, RV’s, patio

furniture, lawn equipment, etc., select white 40°

spray tip.

• For general rinsing (medium pressure and medium

flow), ideal for most all purpose cleaning such as

home siding, brick patios, wood decks, driveways

and sidewalks, garage floors, etc., select yellow

15° spray tip.

• For maximum rinsing (higher pressure and lower

flow), for stubborn or hard to reach surface such as

second story surfaces, paint removal, oil stains, rust

removal or other stubborn substances (tar, gum,

grease, wax, etc.), select red 0° spray tip.

• To apply detergent, applies project specific cleaners

to help break down stubborn dirt and grime on a

variety of surfaces, select black detergent spray tip.

4. Pull back on collar, insert new spray tip and release collar.

Tug on spray tip to make sure it is securely in place.

Usage Tips

• For most effective cleaning, keep spray tip from 8 to

24 inches (20 to 61 cm) away from cleaning surface.

• If you get spray tip too close, especially using a high

pressure spray tip, you may damage surface being

cleaned.

• DO NOT get closer than 6 inches (15 cm) when cleaning

tires.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected,

which can cause injury.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction and squeeze spray

gun trigger, to release high pressure, every time you stop

engine. Engage trigger lock when not in use.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

• NEVER exchange spray tips without locking the trigger lock on

the spray gun.

• DO NOT twist spray tips while spraying.

40° White

1750 PSI

2.3 GPM

15° Yellow

2200 PSI

2.2 GPM

0° Red

2550 PSI

2.0 GPM

Black

Use to apply

chemical

Low Pressure

High Pressure

Cleaning and Applying Detergent

To apply detergent follow these steps:

1. Attach desired detergent siphon hose following

instructions Attach Detergent Siphon Hose to Pump.

IMPORTANT: Be sure engine is off and allowed to cool before

switching detergent siphoning hoses.

2. Review use of spray tips.

3. Prepare detergent solution as required by job.

4. Make sure detergent shut-off valve on cleaning tank is in

“Off” position.

5. If using cleaning tank, pour detergent into cleaning tank.

NOTE: The cleaning tank holds one gallon.

6. Make sure black detergent spray tip is installed.

NOTE: Detergent cannot be applied with the high pressure

nozzles (White, Yellow or Red).

7. Make sure garden hose is connected to water inlet.

Check that high pressure hose is connected to spray gun

and pump. Turn on water.

8. Engage trigger lock on spray gun and start engine

following instructions How to Start Your Pressure

Washer.

9A. If using cleaning tank, rotate detergent shut-off valve on

cleaning tank to “On” position (A).

IMPORTANT: If using detergent siphoning hose, make sure

detergent shut-off valve on cleaning tank is in the “Off”

position.

9B. If using detergent siphoning hose, place small filter end

of detergent siphoning tube into detergent container.

NOTE: Make sure the filter is fully submerged in detergent

while applying detergent.

10. Apply detergent to a dry surface, starting at lower

portion of area to be washed and work upward, using

long, even, overlapping strokes.

11. Allow detergent to "soak in" for 3-5 minutes before

washing and rinsing. Reapply as needed to prevent

surface from drying. DO NOT allow detergent to dry on

(prevents streaking).

Pressure Washer Rinsing

For Rinsing:

1. Engage trigger lock on spray gun.

2. If using cleaning tank, rotate detergent shut-off valve on

cleaning tank to “Off” position.

3. Remove black spray tip from nozzle extension.

4. Select and install desired high pressure spray tip

following instructions How to Use Spray Tips.

5. Keep spray gun a safe distance from area you plan to

spray.

6. Apply a high pressure spray to a small area and then

check surface for damage. If no damage is found, you

can assume it is okay to continue rinsing.

7. Start at top of area to be rinsed, working down with

same overlapping strokes as you used for cleaning.

Automatic Cool Down System (Thermal Relief)

If you run the engine on your pressure washer for

3-5 minutes without pressing the trigger on the spray gun,

circulating water in the pump can reach temperatures above

125°F. The system engages to cool the pump by discharging

the warm water onto the ground.

CAUTION

Chemicals can cause bodily injury, and/or property

damage.

• NEVER use caustic liquid with pressure washer.

• Use ONLY pressure washer safe detergents/soaps. Follow all

manufacturers instructions.

NOTICE

You must attach all hoses before you start the engine.

• Starting the engine without all the hoses connected and without

the water turned ON will damage the pump.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

WARNING

Kickback from spray gun can cause you to fall.

• Operate pressure washer from a stable surface.

• Be extremely careful if you must use the pressure washer from

a ladder, scaffolding, or any other similar location.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

NOTICE

Contact with the hot muffler can damage detergent

siphoning tube.

• When inserting the filter into a detergent solution bottle, route

the tube so as to keep it from inadvertently contacting the hot

muffler.

WARNING

Contact with muffler area can result in serious

burns.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

ENGINE TECHNICAL INFORMATION

This is a single cylinder, L-head, air cooled engine. It is a low

emissions engine.

In the State of California, Model 120000 engines are certified

by the California Air Resources Board to meet emissions

standards for 125 hours. Such certification does not grant

the purchaser, owner or operator of this engine any

additional warranties with respect to the performance or

operational life of this engine. The engine is warranted solely

according to the product and emissions warranties stated

elsewhere in this manual.

Power Ratings

The gross power rating for individual gas engine models is

labeled in accordance with SAE (Society of Automotive

Engineers) code J1940 (Small Engine Power & Torque Rating

Procedure), and rating performance has been obtained and

corrected in accordance with SAE J1995 (Revision 2002-05).

Torque values are derived at 3060 RPM; horsepower values

are derived at 3600 RPM. Actual gross engine power will be

lower and is affected by, among other things, ambient

operating conditions and engine-to-engine variability. Given

both the wide array of products on which engines are placed

and the variety of environmental issues applicable to

operating the equipment, the gas engine will not develop the

rated gross power when used in a given piece of power

equipment (actual "on-site" or net power). This difference is

due to a variety of factors including, but not limited to,

accessories (air cleaner, exhaust, charging, cooling,

carburetor, fuel pump, etc.), application limitations, ambient

operating conditions (temperature, humidity, altitude), and

engine-to-engine variability. Due to manufacturing and

capacity limitations, Briggs & Stratton may substitute an

engine of higher rated power for this Series engine.

PRODUCT SPECIFICATIONS

Pressure Washer Specifications

Max Outlet Pressure . . . . . . . . . . . . 2,550 PSI (175.8 BARS)

Max Flow Rate . . . . . . . . . . . 2.3 GPM (8.7 liters per minute)

Chemical Mix. . . . . . . . . . . . . . . . . . . . . . . . . Use as directed

Water Supply Temperature. . . . Not to exceed 100°F (38° C)

Shipping Weight . . . . . . . . . . . . . . . . . . . . . 72 lbs. (32.7 kg)

Engine Specifications

Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.69 in. (68mm)

Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.04 in. (52mm)

Displacement . . . . . . . . . . . . . . . . . . . . . . . . 11.57 in. (190 cc)

Spark Plug

Type: . . . . . . . . . . . . .

Briggs & Stratton 802592 or 5095D

Set Gap To: . . . . . . . . . . . . . . . . . . . . . . 0.030inch (0.76mm)

Armature Air Gap: . . . . . . . . . . . 0.006-0.010 in.(0.15-0.25mm)

Valve clearance with valve springs installed and piston 1/4 in.

(6 mm) past top dead center (check when engine is cold).

Intake . . . . . . . . . . . . . . . . . . . . 0.005-0.007 in.(0.13-0.18 mm)

Exhaust . . . . . . . . . . . . . . . . . . 0.007-0.009 in.(0.18-0.23 mm)

Fuel Capacity . . . . . . . . . . . . . . . . . . . . . . 1.6 Quarts (1.5 liters)

Oil Capacity . . . . . . . . . . . . . . . . . . . . . . . . 18 Ounces (0.5 liter)

NOTE: For practical operation, the engine load should not

exceed 85% of rated power. Engine power will decrease

3-1/2% for each 1,000 feet (300 meters) above sea level and

1% for each 10° F (5.6° C) above 77° F (25° C). It should

operate satisfactorily at an angle up to 15°.

SPECIFICATIONS

General Recommendations

Regular maintenance will improve the performance and

extend the life of the pressure washer. See any Sears or

other qualified service dealer for service.

The pressure washer warranty does not cover items that

have been subjected to operator abuse or negligence. To

receive full value from the warranty, the operator must

maintain pressure washer as instructed in this manual

including proper storage as detailed in Storage.

Some adjustments will need to be made periodically to

properly maintain your pressure washer.

All service and adjustments should be made at least once

each season. Follow the requirements in the Maintenance

Schedule chart above.

NOTE: Once a year you should clean or replace the spark

plug and replace the air filter. A new spark plug and clean air

filter assure proper fuel-air mixture and help your engine run

better and last longer.

Pump Oil

DO NOT attempt any oil maintenance on this pump. The

pump is pre-lubricated and sealed from the factory, requiring

no additional maintenance for the life of the pump.

Emissions Control

Maintenance, replacement, or repair of the emissions

control devices and systems may be performed by any non-

road engine repair establishment or individual. However,

to obtain ”no charge” emissions control service, the work

must be performed by a Sears or other qualified service

dealer. See the Emissions Warranty.

Before Each Use

1. Check engine oil level.

2. Clean debris.

3. Check water inlet screen for damage.

4. Check high pressure hose for leaks.

5. Check cleaning tank for damage.

6. Check gun and nozzle extension assembly for leaks.

7. Purge pump of air and contaminants.

MAINTENANCE

OWNER’S RESPONSIBILITIES

Follow the hourly or calendar intervals, whichever occurs first.

More frequent service is required when operating in adverse conditions noted below.

Clean if clogged. Replace if perforated or torn.

Change oil after the first (5) operating hours and every 50 hours or yearly thereafter. Change sooner when operating under dirty or dusty conditions.

Replace more often under dirty or dusty conditions.

MAINTENANCE SCHEDULE OPERATING INTERVALS

SERVICE DATES

FILL IN DATES AS YOU COMPLETE

REGULAR SERVICE

MAINTENANCE TASK

Before

Each Use

Every 25

Hours or

Yearly

Every 50

Hours or

Yearly

Every 100

Hours or

Yearly

100-300

Hours

PRESSURE WASHER

Check/clean water inlet screen

Check high pressure hose X

Check detergent hose X

Check spray gun and assembly for leaks X

Purge pump of air and contaminants X

Prepare pump for storage below 32°F See Winter Storage

ENGINE

Check oil level

Clean debris X

Change engine oil X

Service air cleaner X

Service spark plug X

Service spark arrester X

Clean cooling system X

Clean combustion chamber X

Prepare for storage If unit is to remain idle for longer than 30 days.

PRESSURE WASHER MAINTENANCE

Clean Debris

Daily or before use, clean accumulated debris from cleaning

system. Keep linkage, spring and controls clean. Keep area

around and behind muffler free from any combustible debris.

Inspect cooling air slots and openings on the pressure

washer. These openings must be kept clean and

unobstructed.

Cleaning system parts should be kept clean to reduce the risk

of overheating and ignition of accumulated debris.

• Use a damp cloth to wipe exterior surfaces clean.

• Use a soft bristle brush to loosen caked on dirt, oil, etc.

• Use a vacuum cleaner to pick up loose dirt and debris.

Check and Clean Inlet Screen

Examine garden hose inlet screen. Clean if it is clogged or

replace if it is torn.

Check High Pressure Hose

High pressure hoses can develop leaks from wear, kinking,

or abuse. Inspect hose before each use. Check for cuts,

leaks, abrasions, bulging of cover, or damage or movement

of couplings. If any of these conditions exist, replace hose

immediately.

Check Gun and Nozzle Extension

Examine hose connection to spray gun and make sure it is

secure. Test trigger by pressing it and making sure it springs

back into place when you release it. Put safety latch in UP

position and test trigger. You should not be able to press

trigger. Replace spray gun immediately if it fails any of these

tests.

Nozzle Maintenance

A pulsing sensation felt while squeezing the spray gun trigger

may be caused by excessive pump pressure. The principal

cause of excessive pump pressure is a spray tip clogged or

restricted with foreign materials, such as dirt, etc. To correct

the problem, immediately clean the spray tip following these

instructions:

1. Shut off engine and turn off water supply.

2. ALWAYS point spray gun in a safe direction and squeeze

spray gun trigger to release retained high water pressure.

3. Remove spray tip from end of nozzle extension.

4. Use a small paper clip to free any foreign material

clogging or restricting spray tip (A).

5. Remove nozzle extension from spray gun.

6. Using a garden hose, remove additional debris by back

flushing water through nozzle extension. Back flush

between 30 to 60 seconds.

7. Reinstall spray tip into nozzle extension.

8. Reconnect nozzle extension to spray gun.

9. Make sure garden hose is connected to water inlet.

Check that high pressure hose is connected to spray gun

and pump. Turn on water.

10. Engage trigger lock on spray gun and start engine

following instructions How to Start Your Pressure Washer.

11. Test pressure washer by operating with each quick

connect spray tip.

O–Ring Maintenance

Purchase an O–Ring Repair Kit at your local Sears or by

calling 1-800-4-MY-HOME (469-4663) or online at

www.sears.com. It is not included with the pressure washer.

This kit includes replacement o-rings, rubber washer and

water inlet filter. Refer to the instruction sheet provided in the

kit to service your unit’s o-rings.

NOTICE

Improper treatment of pressure washer can damage it and

shorten its life.

• DO NOT insert any objects through cooling slots.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

• NEVER repair high pressure hose. Replace it.

• Replacement hose rating MUST exceed maximum pressure

rating of unit.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected,

which can cause injury.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction and squeeze spray

gun trigger, to release high pressure, every time you stop

engine. Engage trigger lock when not in use.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

• NEVER repair leaking connections with sealant of any kind.

Replace o-ring or seal.

ENGINE MAINTENANCE

Oil

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty

Certified oils for best performance. Other high-quality

detergent oils are acceptable if classified for service SF, SG,

SH, SJ or higher. DO NOT use special additives.

Outdoor temperatures determine the proper oil viscosity for

the engine. Use the chart to select the best viscosity for the

outdoor temperature range expected.

* Below 40°F (4°C) the use of SAE 30 will result in hard starting.

** Above 80°F (27°C) the use of 10W30 may cause increased oil

consumption. Check oil level more frequently.

NOTE: Synthetic oil meeting ILSAC GF-2, API

certification mark and API service symbol with

“SJ/CF ENERGY CONSERVING” or higher, is an

acceptable oil at all temperatures. Use of synthetic oil

does not alter required oil change intervals.

Checking Oil Level

Oil level should be checked prior to each use or at least every

5 hours of operation. Keep oil level maintained.

1. Make sure pressure washer is on a level surface.

2. Remove oil dipstick and wipe dipstick with clean cloth.

Replace and tighten dipstick. Remove and and check oil

level.

3. Verify oil is at “Full” mark on dipstick. Replace and

tighten dipstick.

Adding Engine Oil

1. Make sure pressure washer is on a level surface.

2. Check oil level as described in Checking Oil Level.

3. If needed, slowly pour oil into oil fill opening to the

“Full” mark on dipstick. DO NOT overfill.

4. Replace and tighten dipstick.

WARNING

Unintentional sparking can result in fire or

electric shock.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

PRESSURE WASHER

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOTcheck for spark with spark plug removed.

NOTICE

Overfilling with oil may cause the engine to not start, or

hard starting.

• DO NOT overfill.

• If over the FULL mark on dipstick, drain oil to reduce oil level to

FULL mark on dipstick.

Changing Engine Oil

Change engine oil after the first 5 hours and every 50 hours

thereafter. If you are using your pressure washer under

extremely dirty or dusty conditions, or in extremely hot

weather, change oil more often.

KEEP OUT OF REACH OF CHILDREN. DON'T

POLLUTE. CONSERVE RESOURCES. RETURN

USED OIL TO COLLECTION CENTERS.

Change oil while engine is still warm from running, as

follows:

1. Drain fuel tank by running pressure washer until fuel

tank is empty.

2. Disconnect spark plug wire and keep it away from spark

plug.

3. Clean area around oil fill, remove oil fill cap/dipstick.

Wipe dipstick clean.

4. Tip your pressure washer to drain oil from oil fill into a

suitable container making sure you tip your unit away

from spark plug. When crankcase is empty, return

pressure washer to upright position.

5. Slowly pour recommended oil (about 18 oz. (0.5 l)) into

oil fill opening. Pause to permit oil to settle. Fill to “Full”

mark on dipstick.

6. Wipe dipstick clean each time oil level is checked. DO

NOT overfill.

7. Replace and tighten dipstick.

8. Wipe up any remaining oil.

9. Reconnect spark plug wire to spark plug.

Service Air Cleaner

Your engine will not run properly and may be damaged if you

run it with a dirty air cleaner.

Service the air cleaner once every 25 hours of operation or

once each year, whichever comes first. Service more often if

operating under dirty or dusty conditions. Replacements are

available at your local Sears service center.

To service the air cleaner, follow these steps:

1. Loosen screw (A) and tilt cover (B) down.

2. Carefully remove cartridge (C) assembly.

3. To clean cartridge, gently tap pleated paper side on a flat

surface.

4. Reinstall clean or new cartridge assembly inside cover.

5. Insert cover’s tabs (D) into slots in bottom of base (E).

6. Tilt cover up and tighten screw securely to base.

NOTE: You can purchase new air filter elements by calling

1-800-4-MY-HOME (469-4663).

Service Spark Plug

Service the spark plug every 100 hours of operation or

yearly, whichever occurs first.

1. Clean area around spark plug.

2. Remove and inspect spark plug.

3. Replace spark plug if electrodes are pitted, burned or

porcelain is cracked. Use the recommended replacement

plug. See Specifications.

4. Check electrode gap with wire feeler gauge and set spark

plug gap to 0.030 inch (0.76 mm) if necessary.

5. Install spark plug and tighten firmly.

NOTE: You can purchase a new spark plug by calling

1-800-4-MY-HOME (469-4663).

CAUTION

Avoid prolonged or repeated skin contact with used motor

oil.

• Used motor oil has been shown to cause skin cancer in certain

laboratory animals.

• Thoroughly wash exposed areas with soap and water.

Spark Arrester Service

Your engine is not factory-equipped with a spark arrester. In

some areas, it is illegal to operate an engine without a spark

arrester. Check local laws and regulations. A spark arrester is

available from your nearest Sears service center. If you need

to order a spark arrester, please call 1-800-4-MY-HOME

(469-4663).

The spark arrester must be serviced every 50 hours to keep it

functioning as designed.

If the engine has been running, the muffler will be very hot.

Allow the muffler to cool before servicing the spark arrester.

• Remove spark arrester screen for cleaning and inspection.

• Replace if screen is damaged.

Air Cooling System

Over time debris may accumulate in cylinder cooling fins and

cannot be observed without partial engine disassembly. For

this reason, we recommend you have a qualified Sears

service dealer clean the cooling system per recommended

intervals (see Maintenance Schedule). Equally important is to

keep top of engine free from debris. See Clean Debris.

Clean Combustion Chamber

We recommend you have a qualified Sears service dealer

remove combustion deposits from the cylinder, cylinder head,

top of piston and around valves per recommended intervals

(see Maintenance Schedule).

AFTER EACH USE

Water should not remain in the unit for long periods of time.

Sediments or minerals can deposit on pump parts and

“freeze” pump action. Follow these procedures after every

use:

1. Flush detergent system by turning its detergent shut-off

valve to “Off” position and run pressure washer with

black detergent spray tip. Flush for one to two minutes.

2. Shut off engine, turn off water supply, point gun in a

safe direction and squeeze trigger to relieve trapped

pressure, engage trigger lock on spray gun and let

engine cool.

3. Disconnect hose from spray gun and high pressure

outlet on pump. Drain water from hose, gun, and nozzle

extension. Use a rag to wipe off the hose.

4. Empty pump of all pumped liquids by pulling recoil

handle about 6 times. This should remove most liquid in

pump.

5. Coil high pressure hose and properly hang it on hook

provided on handle.

6. Store unit in a clean, dry area.

7. If storing for more than 30 days see Long Term Storage

on next page.

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers, or other appliances that have pilot light or other ignition

source because they can ignite fuel vapors.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected,

which can cause injury.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction and squeeze spray

gun trigger, to release high pressure, every time you stop

engine. Engage trigger lock when not in use.

WARNING

Contact with muffler area can result in serious

burns.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (1.5 m) of clearance on all sides of

pressure washer including overhead.

• Code of Federal Regulation (CFR) Title 36 Parks, Forests, and

Public Property require equipment powered by an internal

combustion engine to have a spark arrester, maintained in

effective working order, complying to USDA Forest service

standard 5100-1C or later revision. In the State of California a

spark arrester is required under section 4442 of the California

Public resources code. Other states may have similar laws.

Keep areas within heavy line clear of debris.

La page charge ...

Simplicity 020323-0 Manuel utilisateur

Marque: Simplicity

Modèle: 020323-0

Catégorie: Nettoyeurs haute pression

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Simplicity 020323-0 User manual

Documents connexes

Autres documents

BE Pressure Supply 9178468 Le manuel du propriétaire