Simplicity 020322-0 Manuel utilisateur

Marque: Simplicity

Modèle: 020322-0

Catégorie: Nettoyeurs haute pression

Taper: Manuel utilisateur

2000 PSI

1.9 GPM

PRESSURE WASHER

Operator’s Manual

Model No. 580.676620

Part No. 203799GS Draft - (11/14/2007)

• Safety

• Assembly

• Operation

• Maintenance

• Parts

• Français, p. 32

HOURS: Mon. - Fri. 8 a.m. to 5 p.m. (CT)

PRESSURE WASHER

CUSTOMER HELPLINE

1-800-222-3136

Sears Canada, Inc.

Visit our Craftsman website: www.sears.ca

AVERTISSEMENT

Avant d’utiliser ce produit, veuillez lire le

manuel et suivre toutes les directives

relatives à la sécurité et à l’utilisation.

WARNING

Before using this product, read this

manual and follow all Safety Rules

and Operating Instructions.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages

that follow this symbol to avoid possible injury or death.

Read this manual carefully and become familiar

with your pressure washer. Know its applications,

its limitations, and any hazards involved.

The safety alert symbol ( ) is used with a signal word

(DANGER, CAUTION, WARNING), a pictorial and/or a safety

message to alert you to hazards. DANGER indicates a hazard

which, if not avoided, will result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury. CAUTION indicates a hazard

which, if not avoided, might result in minor or moderate

injury. NOTICE indicates a situation that could result in

equipment damage. Follow safety messages to avoid or

reduce the risk of injury or death.

Hazard Symbols and Meanings

SAFETY RULES

WARRANTY

TABLE OF CONTENTS

ONE-YEAR FULL WARRANTY ON CRAFTSMAN PRESSURE WASHER

If this pressure washer fails due to a defect in material or workmanship within one year from the date of purchase, return it to

any Sears store, other Craftsman outlet, or Sears Parts & Repair Center in the United States or Canada for free repair (or

replacement if repair proves impossible).

All warranty coverage applies for only 90 days from date of purchase if this pressure washer is ever used for commercial or

rental purposes.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., Hoffman Estates, IL 60179

Sears Canada Inc., Toronto, Ontario, Canada M5B 2B8

WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

FEATURES AND CONTROLS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9

OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-13

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-19

STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-26

EMISSION CONTROL WARRANTY . . . . . . . . . . . . . . . . . . . . . 27-28

NOTES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29-31

FRANÇAIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32-55

HOW TO ORDER PARTS . . . . . . . . . . . . . . . . . . . . . . . . BACK PAGE

Fire

Explosion

Toxic Fumes

Hot Surface

Moving Parts

Electrical Shock

Slippery Surface

Fall

Kickback

Flying Objects

Fluid Injection

Operator’s Manual

WARNING

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

WARNING

Running engine gives off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide can cause headache,

fatigue, dizziness, vomiting, confusion, seizures,

nausea, fainting or death.

Some chemicals or detergents may be harmful if

inhaled or ingested, causing severe nausea,

fainting, or poisoning.

• Operate pressure washer ONLY outdoors.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes, or other openings.

• DO NOT start or run engine indoors or in an enclosed area,

even if windows and doors are open.

• Use a respirator or mask whenever there is a chance that

vapors may be inhaled.

• Read all instructions with mask so you are certain the mask will

provide the necessary protection against inhaling harmful

vapors.

WARNING

Risk of electrocution.

Contact with power source can cause electric

shock or burn.

• NEVER spray near power source.

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WHEN ADDING OR DRAINING FUEL

• Turn pressure washer OFF and let it cool at least 2 minutes

before removing fuel cap. Loosen cap slowly to relieve pressure

in tank.

• Fill or drain fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

WHEN STARTING EQUIPMENT

• Ensure spark plug, muffler, fuel cap, and air cleaner are in

place.

• DO NOT crank engine with spark plug removed.

WHEN OPERATING EQUIPMENT

• DO NOT tip engine or equipment at angle which causes fuel to

spill.

• DO NOT spray flammable liquids.

WHEN TRANSPORTING OR REPAIRING EQUIPMENT

• Transport/repair with fuel tank EMPTY or with fuel shutoff valve

OFF.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers, or other appliances that have pilot light or other ignition

source because they can ignite fuel vapors.

WARNING

Use of pressure washer can create puddles and

slippery surfaces.

Kickback from spray gun can cause you to fall.

• Operate pressure washer from a stable surface.

• The cleaning area should have adequate slopes and drainage to

reduce the possibility of a fall due to slippery surfaces.

• Be extremely careful if you must use the pressure washer from

a ladder, scaffolding, or any other similar location.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

WARNING

Starter cord kickback (rapid retraction) can result

in bodily injury. Kickback will pull hand and arm

toward engine faster than you can let go.

Broken bones, fractures, bruises, or sprains

could result.

• NEVER pull starter cord without first relieving spray gun

pressure.

• When starting engine, pull cord slowly until resistance is felt

and then pull rapidly to avoid kickback.

• After each starting attempt, where engine fails to run, always

point spray gun in safe direction and squeeze spray gun trigger

to release high pressure. Engage spray gun trigger lock.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

WARNING

Contact with muffler area can result in serious

burns.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (152 cm) of clearance on all sides of

pressure washer including overhead.

• Code of Federal Regulation (CFR) Title 36 Parks, Forests, and

Public Property require equipment powered by an internal

combustion engine to have a spark arrester, maintained in

effective working order, complying to USDA Forest service

standard 5100-1C or later revision. In the State of California a

spark arrester is required under section 4442 of the California

Public resources code. Other states may have similar laws.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected,

which can cause injury.

• DO NOT allow CHILDREN to operate pressure washer.

• NEVER repair high pressure hose. Replace it.

• NEVER repair leaking connections with sealant of any kind.

Replace o-ring or seal.

• NEVER connect high pressure hose to nozzle extension.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction and squeeze spray

gun trigger, to release high pressure, every time you stop

engine. Engage trigger lock when not in use.

• NEVER aim spray gun at people, animals, or plants.

• DO NOT secure spray gun in open position.

• DO NOT leave spray gun unattended while machine is running.

• NEVER use a spray gun which does not have a trigger lock or

trigger guard in place and in working order.

• Always be certain spray gun, nozzles and accessories are

correctly attached.

WARNING

Unintentional sparking can result in fire or

electric shock.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

PRESSURE WASHER

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

WARNING

Risk of eye injury.

Spray can splash back or propel objects.

• Always wear safety goggles when using this equipment or in

vicinity of where equipment is in use.

• Before starting the pressure washer, be sure you are wearing

adequate safety goggles.

• NEVER substitute safety glasses for safety goggles.

WARNING

Starter and other rotating parts can entangle

hands, hair, clothing, or accessories.

• NEVER operate pressure washer without protective housing or

covers.

• DO NOT wear loose clothing, jewelry or anything that may be

caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

NOTICE

High pressure spray may damage fragile items including

glass.

• DO NOT point spray gun at glass when in jet spray mode.

• NEVER aim spray gun at plants.

NOTICE

Improper treatment of pressure washer can damage it and

shorten its life.

• If you have questions about intended use, ask dealer or contact

Sears.

• NEVER operate units with broken or missing parts, or without

protective housing or covers.

• DO NOT by-pass any safety device on this machine.

• DO NOT tamper with governed speed.

• DO NOT operate pressure washer above rated pressure.

• DO NOT modify pressure washer in any way.

• Before starting pressure washer in cold weather, check all parts

of the equipment to be sure ice has not formed there.

• NEVER move machine by pulling on hoses. Use handle

provided on unit.

• Check fuel system for leaks or signs of deterioration, such as

chafed or spongy hose, loose or missing clamps, or damaged

tank or cap. Correct all defects before operating pressure

washer.

• This equipment is designed to be used with Sears authorized

parts ONLY. If equipment is used with parts that DO NOT

comply with minimum specifications, user assumes all risks

and liabilities.

KNOW YOUR PRESSURE WASHER

Read the Operator’s Manual and safety rules before operating your pressure washer.

Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls and

adjustments. Save this manual for future reference.

FEATURES AND CONTROLS

A - Recoil Starter — Used for starting the engine manually.

B - Oil Fill/Dipstick — Check, add and drain engine oil here.

C - Pump — Develops high pressure.

D - Automatic Cool Down System — Cycles water through

pump when water reaches 125°-155°F. Warm water will

discharge from pump onto ground. This system prevents

internal pump damage.

E - High Pressure Hose — Connect one end to water pump

and the other end to spray gun.

F - Adjustable Nozzle Extension — Attach to spray gun to

use adjustable nozzle. Adjust for high or low pressure;

narrow or fan spray.

G - Spray Gun — Controls the application of water onto

cleaning surface with trigger device. Includes trigger lock.

H - Warning/Operating Instructions Tag — Identifies

hazards and proper procedure to start/stop pressure

washer.

J - Fuel Tank — Fill tank with regular unleaded fuel. Always

leave room for fuel expansion.

Items Not Shown:

Air Filter — Protects engine by filtering dust and debris out

of intake air.

Data Tag (near rear of base plate) — Provides model and

serial number of pressure washer. Please have these readily

available if calling for assistance.

High Pressure Outlet — Connection for high pressure hose.

Primer Bulb — Prepares a cold engine for starting.

Safety Goggles — Always use the enclosed safety goggles

when running your pressure washer.

Throttle Lever — Sets engine in starting mode for recoil

starter and stops a running engine.

Water Inlet — Connection for garden hose.

Your pressure washer requires some assembly and is ready

for use only after it has been properly serviced with the

recommended oil and fuel.

If you have any problems with the assembly of your

pressure washer, please call the pressure washer helpline

at 1-800-222-3136.

UNPACK THE PRESSURE WASHER

1. Remove everything from carton except pressure washer.

2. Open carton completely by cutting each corner from top

to bottom.

3. Remove pressure washer from carton.

CARTON CONTENTS

Check all contents. If any parts are missing or damaged, call

the pressure washer helpline at 1-800-222-3136.

• Main Unit

• Handle

• Wheel Kit

• High Pressure Hose

• Spray Gun

• Adjustable Nozzle Extension

• Oil Bottle

• Parts Bag (which includes the following):

• Operator’s Manual

• Safety Goggles

• Mesh Accessory Bag

Become familiar with each piece before assembling the

pressure washer. Identify all contents with the illustration on

page 6. If any parts are missing or damaged, call the

pressure washer helpline at 1-800-222-3136.

ASSEMBLING PRESSURE WASHER

Your Craftsman pressure washer will need assembly before

operation:

1. Attach handle to main unit.

2. Install wheel kit.

3. Add oil to engine crankcase.

4. Add fuel to fuel tank.

5. Connect pressure hose to spray gun and pump.

6. Connect water supply to pump.

7. Attach nozzle extension to spray gun.

Attach Handle

1. Place handle (A) onto base (B). Make sure holes in

handle align with holes on base.

2. Insert carriage bolts (C) through holes from outside of

unit and attach a plastic knob (D) from inside of unit.

Tighten by hand.

Install Wheel Kit

The wheel kit is designed to greatly improve the portability of

your pressure washer.

NOTE: Wheel kit is not intended for over-the-road use.

Install the wheel kit as follows:

1. Place the bottom of the pressure washer frame on a flat,

even surface.

2. Slide a wheel (A) over the axle pin (B).

NOTE: Be sure to install wheel with raised hub inboard.

3. Slide axle pin through hole (C) in frame.

4. Retain wheel on axle pin with retaining pin (D).

5. Repeat step 2 through 4 to secure second wheel.

ASSEMBLY

Add Engine Oil

1. Place pressure washer on a flat, level surface.

2. Clean area around oil fill and remove yellow oil fill

cap/dipstick.

3. Using oil funnel (optional), slowly pour contents of

provided oil bottle into oil fill opening.

4. Replace oil fill cap/dipstick and fully tighten.

Add Fuel

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). High altitude

use, see High Altitude.

• Gasoline with up to 10% ethanol (gasohol) or up to 15%

MTBE (methyl tertiary butyl ether) is acceptable.

To protect the fuel system from gum formation, mix in a fuel

stabilizer when adding fuel. See Storage. All fuel is not the

same. If you experience starting or performance problems

after using fuel, switch to a different fuel provider or change

brands. This engine is certified to operate on gasoline. The

emission control system for this engine is EM (Engine

Modifications).

1. Clean area around fuel fill cap, remove cap.

2. Slowly add regular unleaded fuel (A) to fuel tank (B). Be

careful not to overfill. Allow about 1.5" (4 cm) (C) of tank

space for fuel expansion.

3. Install fuel cap and wait for any spilled fuel to evaporate.

CAUTION! Alcohol-blended fuels (called gasohol, ethanol or

methanol) can attract moisture, which leads to separation and

formation of acids during storage. Acidic gas can damage the

fuel system of an engine while in storage.

To avoid engine problems, the fuel system should be treated

with a fuel preserver or emptied before storage of 30 days or

longer. If adding a fuel preserver, fill the fuel tank with fresh

fuel. If only partially filled, air in the tank will promote fuel

deterioration during storage. If fuel preserver is not used,

drain the fuel tank, start the engine and let it run until the fuel

lines and carburetor are empty. Use fresh fuel next season.

See Storage for additional information.

NEVER use engine or carburetor cleaner products in the fuel

tank as permanent damage may occur.

NOTICE

Improper treatment of pressure washer can damage it and

shorten its life.

• DO NOT attempt to crank or start the engine before it has been

properly serviced with the recommended oil. This may result in

an engine failure.

NOTICE

Avoid pressure washer damage.

Failure to follow Operator’s Manual for fuel

recommendations voids warranty.

• DO NOT use unapproved gasoline such as E85.

• DO NOT mix oil in gasoline.

• DO NOT modify engine to run on alternate fuels.

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WHEN ADDING FUEL

• Turn pressure washer OFF and let it cool at least 2 minutes

before removing fuel cap. Loosen cap slowly to relieve pressure

in tank.

• Fill fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum 85

octane / 85 AKI (89 RON) gasoline is acceptable. To remain

emissions compliant, high altitude adjustment is required.

Operation without this adjustment will cause decreased

performance, increased fuel consumption, and increased

emissions. See a qualified Sears dealer for high altitude

adjustment information. Operation of the engine at altitudes

below 2,500 feet (762 meters) with the high altitude kit is not

recommended.

Connect Hose and Water Supply to Pump

NOTE: Remove and discard the shipping caps from the

pump’s high pressure outlet and water inlet before attaching

hoses.

1. Uncoil high pressure hose and attach one end of hose to

base of spray gun. Tighten by hand.

2. Attach other end of high pressure hose to high pressure

outlet on pump. Tighten by hand.

3. Before connecting garden hose to water inlet, inspect

inlet screen (A). Clean screen if it contains debris or have

it replaced if damaged. DO NOT run pressure washer if

inlet screen is damaged or missing.

4. Run water through garden hose for 30 seconds to flush

it of debris. Turn off water.

IMPORTANT: DO NOT siphon standing water for the water

supply. Use ONLY cold water (less than 100°F).

5. Connect garden hose (not to exceed 50 feet in length) to

water inlet. Tighten by hand.

6. Turn ON water, point gun in a safe direction and squeeze

trigger to purge pump system of air and impurities.

CHECKLIST BEFORE STARTING ENGINE

Review the unit to ensure you have performed all of the

following:

1. Be sure to read Safety Rules and Operation sections

before using the pressure washer.

2. Make sure handle is in place and secure.

3. Check that oil has been added to proper level in engine

crankcase.

4. Add proper fuel to fuel tank.

5. Check for proper hose connections (high pressure and

water supply) and that there are no kinks, cuts, or

damage to the high pressure hose.

6. Provide proper water supply (not to exceed 100°F).

NOTICE

DO NOT run the pump without the water supply connected

and turned on.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

• NEVER connect high pressure hose to nozzle extension.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• Always be certain spray gun, nozzles and accessories are

correctly attached.

NOTICE

Using a One Way Valve (vacuum breaker or check valve) at

pump inlet can cause pump or inlet connector damage.

• There MUST be at least ten feet of unrestricted garden hose

between the pressure washer inlet and any device, such as a

vacuum breaker or check valve.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

WARNING

Risk of eye injury.

Spray can splash back or propel objects.

• Always wear safety goggles when using this equipment or in

vicinity of where equipment is in use.

• Before starting the pressure washer, be sure you are wearing

adequate safety goggles.

• NEVER substitute safety glasses for safety goggles.

HOW TO USE YOUR PRESSURE WASHER

If you have any problems operating your pressure washer,

please call the pressure washer helpline at 1-800-222-3136.

Pressure Washer Location

Pressure Washer Clearance

Place pressure washer outdoors in an area that will not

accumulate deadly exhaust gas. DO NOT place pressure

washer where exhaust gas (A) could accumulate and enter

inside or be drawn into a potentially occupied building.

Ensure exhaust gas is kept away from any windows, doors,

ventilation intakes, or other openings that can allow exhaust

gas to collect in a confined area. Prevailing winds and air

currents should be taken into consideration when positioning

pressure washer.

To Start Your Pressure Washer

To start your engine-powered pressure washer for the first

time, follow these instructions step-by-step. This information

also applies whenever you start the engine after you have let

the pressure washer sit idle for at least a day.

1. Place pressure washer outside near an water source

capable of supplying water at a flow rate greater than

2.9 gallons per minute and no less than 20 PSI at

pressure washer end of garden hose.

2. Check that high pressure hose is tightly connected to

spray gun and pump. See Assembly for illustrations.

3. Make sure unit is in a level position.

4. Connect garden hose to water inlet on pressure washer

pump.

5. Turn ON water, point gun in a safe direction and squeeze

trigger to purge pump system of air and impurities.

6. Attach nozzle extension to spray gun. Tighten by hand.

7. Engage trigger lock (A) on spray gun trigger.

OPERATION

WARNING

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

• Keep at least 5 ft. (152 cm) clearance on all sides of pressure

washer including overhead.

WARNING

Running engine gives off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide can cause headache,

fatigue, dizziness, vomiting, confusion, seizures,

nausea, fainting or death.

• Operate pressure washer ONLY outdoors.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes, or other openings.

• DO NOT start or run engine indoors or in an enclosed area,

even if windows and doors are open.

NOTICE

DO NOT run the pump without the water supply connected

and turned on.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

8. Move throttle lever to “Fast” position (A), shown as a

rabbit.

To start the engine for the very first time:

9. Push primer bulb firmly 5 times, waiting 2 seconds

between each push.

To start engine thereafter:

9. Press primer bulb firmly 3 times, waiting 2 seconds

between each push. For a warm engine, DO NOT press

primer bulb.

IMPORTANT: Before starting the pressure washer, be sure

you are wearing adequate safety goggles.

10. When starting engine, position yourself as

recommended and grasp starter grip handle and pull

slowly until you feel some resistance. Then pull rapidly

to start engine.

11. Return recoil starter slowly. DO NOT let rope “snap

back” against starter.

NOTE: Always keep the throttle lever in the “Fast” position

when operating the pressure washer.

WARNING

Starter cord kickback (rapid retraction) can result

in bodily injury. Kickback will pull hand and arm

toward engine faster than you can let go.

Broken bones, fractures, bruises, or sprains

could result.

• NEVER pull starter cord without first relieving spray gun

pressure.

• When starting engine, pull cord slowly until resistance is felt

and then pull rapidly to avoid kickback.

• After each starting attempt, where engine fails to run, always

point spray gun in safe direction and squeeze spray gun trigger

to release high pressure. Engage spray gun trigger lock.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

WARNING

Contact with muffler area can result in serious

burns.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (152 cm) of clearance on all sides of

pressure washer including overhead.

• Code of Federal Regulation (CFR) Title 36 Parks, Forests, and

Public Property require equipment powered by an internal

combustion engine to have a spark arrester, maintained in

effective working order, complying to USDA Forest service

standard 5100-1C or later revision. In the State of California a

spark arrester is required under section 4442 of the California

Public resources code. Other states may have similar laws.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected,

which can cause injury.

• DO NOT allow CHILDREN to operate pressure washer.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• NEVER aim spray gun at people, animals, or plants.

• DO NOT secure spray gun in open position.

• DO NOT leave spray gun unattended while machine is running.

• NEVER use a spray gun which does not have a trigger lock or

trigger guard in place and in working order.

• Always be certain spray gun, nozzles and accessories are

correctly attached.

WARNING

Risk of eye injury.

Spray can splash back or propel objects.

• Always wear safety goggles when using this equipment or in

vicinity of where equipment is in use.

• Before starting the pressure washer, be sure you are wearing

adequate safety goggles.

• NEVER substitute safety glasses for safety goggles.

How to Stop Your Pressure Washer

1. Release spray gun trigger and let engine idle for two

minutes.

2. Move throttle to SLOW position, then STOP position (A).

3. ALWAYS point spray gun in a safe direction and squeeze

spray gun trigger to release retained high water

pressure.

IMPORTANT: Spray gun traps high water pressure, even

when engine is stopped and water is disconnected.

4. Engage trigger lock on spray gun when not in use.

How To Use the Adjustable Nozzle

You should now know how to START and STOP your

pressure washer. The information in this section will tell you

how to adjust the spray pattern and to apply pressure washer

specific detergents.

1. Slide nozzle backward to achieve high pressure. Slide

nozzle forward when you wish to adjust spray to low

pressure mode.

2. Point nozzle down towards a firm surface, disengage

trigger lock, and press trigger to test pattern.

3. Twisting nozzle adjusts spray pattern from a fan pattern

to a narrow pattern.

Usage Tips

4 For most effective cleaning, keep spray nozzle from 8 to

24 inches away from cleaning surface.

5 If you get spray nozzle too close, especially using high

pressure mode, you may damage surface being cleaned.

6 DO NOT get closer than 6 inches when cleaning tires.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected,

which can cause injury.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction and squeeze spray

gun trigger, to release high pressure, every time you stop

engine. Engage trigger lock when not in use.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

• NEVER adjust spray pattern when spraying.

• NEVER put hands in front of nozzle to adjust spray pattern.

Applying Detergent with Adjustable Nozzle

To apply detergent, follow these steps:

1. Review use of adjustable nozzle.

2. Prepare detergent solution as required by job.

3. Place filter end of detergent siphoning tube into

detergent container.

NOTE: Make sure the filter is fully submerged in detergent

while applying detergent.

4. Slide adjustable nozzle forward to low pressure mode.

NOTE: Detergent cannot be applied with nozzle in high

pressure position.

5. Make sure garden hose is connected to water inlet.

Check that high pressure hose is connected to spray gun

and pump. Turn on water.

6. Engage trigger lock on spray gun and start engine

following instructions How to Start Your Pressure Washer.

7. Apply detergent to a dry surface, starting at lower

portion of area to be washed and work upward, using

long, even, overlapping strokes.

8. Allow detergent to "soak in" for 3-5 minutes before

washing and rinsing. Reapply as needed to prevent

surface from drying. DO NOT allow detergent to dry on

(prevents streaking).

IMPORTANT: You must flush the detergent siphoning system

after each use by placing the filter into a bucket of clean

water, then run the pressure washer in low pressure for

1-2 minutes.

Pressure Washer Rinsing

For Rinsing:

1. Slide nozzle backward to high pressure, press trigger

and wait for detergent to clear.

NOTE: You can also stop detergent flow by removing

detergent siphoning tube from container.

2. Keep spray gun a safe distance from area you plan to

spray.

3. Apply a high pressure spray to a small area, then check

surface for damage. If no damage is found, it is okay to

continue cleaning.

4. Start at top of area to be rinsed, working down with

same overlapping strokes as you used for washing and

applying detergent.

Cleaning Detergent Siphoning Tube

If you used the detergent siphoning tube, you must flush it

with clean water before stopping the engine.

1. Place detergent siphoning tube/filter in a bucket full of

clean water.

2. Engage trigger lock on spray gun.

3. Slide adjustable nozzle forward to low pressure position.

4. Flush for 1-2 minutes.

5. Shut off engine following instructions How to Stop

Pressure Washer and turn off water supply.

6. ALWAYS point gun in a safe direction and squeeze spray

gun trigger to release retained high water pressure.

IMPORTANT: Spray gun traps high water pressure, even when

engine is stopped and water is disconnected.

Automatic Cool Down System (Thermal Relief)

If you run the engine on your pressure washer for

3-5 minutes without pressing the trigger on the spray gun,

circulating water in the pump can reach temperatures above

125°F. The system engages to cool the pump by discharging

the warm water onto the ground.

CAUTION

Chemicals can cause bodily injury, and/or property

damage.

• NEVER use caustic liquid with pressure washer.

• Use ONLY pressure washer safe detergents/soaps. Follow all

manufacturers instructions.

NOTICE

You must attach all hoses before you start the engine.

• Starting the engine without all the hoses connected and without

the water turned ON will damage the pump.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

WARNING

Kickback from spray gun can cause you to fall.

• Operate pressure washer from a stable surface.

• Be extremely careful if you must use the pressure washer from

a ladder, scaffolding, or any other similar location.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

NOTICE

Contact with the hot muffler can damage detergent

siphoning tube.

• When inserting the filter into a detergent solution bottle, route

the tube so as to keep it from inadvertently contacting the hot

muffler.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected,

which can cause injury.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction and squeeze spray

gun trigger, to release high pressure, every time you stop

engine. Engage trigger lock when not in use.

ENGINE TECHNICAL INFORMATION

This is a single cylinder, L-head, air cooled engine. It is a low

emissions engine.

In the State of California, Model 90000 engines are certified

by the California Air Resources Board to meet emissions

standards for 125 hours. Such certification does not grant

the purchaser, owner or operator of this engine any

additional warranties with respect to the performance or

operational life of this engine. The engine is warranted solely

according to the product and emissions warranties stated

elsewhere in this manual.

Power Ratings

The gross power rating for individual gas engine models is

labeled in accordance with SAE (Society of Automotive

Engineers) code J1940 (Small Engine Power & Torque

Rating Procedure), and rating performance has been

obtained and corrected in accordance with SAE J1995

(Revision 2002-05). Torque values are derived at 3060 RPM;

horsepower values are derived at 3600 RPM. Actual gross

engine power will be lower and is affected by, among other

things, ambient operating conditions and engine-to-engine

variability. Given both the wide array of products on which

engines are placed and the variety of environmental issues

applicable to operating the equipment, the gas engine will not

develop the rated gross power when used in a given piece of

power equipment (actual "on-site" or net power). This

difference is due to a variety of factors including, but not

limited to, accessories (air cleaner, exhaust, charging,

cooling, carburetor, fuel pump, etc.), application limitations,

ambient operating conditions (temperature, humidity,

altitude), and engine-to-engine variability. Due to

manufacturing and capacity limitations, Briggs & Stratton

may substitute an engine of higher rated power for this

Series engine.

PRODUCT SPECIFICATIONS

Pressure Washer Specifications

Outlet Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . 2,000 PSI

Flow Rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.9 GPM

Detergent Mix . . . . . . . . . . . . . . . . . . . . . . . . Use as directed

Water Supply Temperature . . . . . . . . . . Not to exceed 100°F

Shipping Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 lbs.

Engine Specifications

Bore . . . . . . . . . . . . . . . . . . . . . . . . . . 2.562 in. (65.09 mm)

Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . 1.75 in. (44.45 mm)

Displacement . . . . . . . . . . . . . . . . . . . . . 9.02 in. (147.8 cc)

Spark Plug

Type: . . . . . . . . . . . . Briggs & Stratton 802592 or 5095D

Set Gap To: . . . . . . . . . . . . . . . . . . . 0.030inch (0.76mm)

Armature Air Gap: . . . . . . . . 0.006-0.010 in. (0.15-0.25mm)

Valve clearance with valve springs installed and piston 1/4 in.

(6 mm) past top dead center (check when engine is cold).

Intake . . . . . . . . . . . . . . . . . 0.005-0.007 in. (0.13-0.18 mm)

Exhaust . . . . . . . . . . . . . . . 0.007-0.009 in. (0.18-0.23 mm)

Fuel Capacity . . . . . . . . . . . . . . . . . . 1.0 Quarts (0.95 Liters)

Oil Capacity . . . . . . . . . . . . . . . . . . . . . . . . 18 Ounces (0.5 liter)

NOTE: For practical operation, the engine load should not

exceed 85% of rated power. Engine power will decrease

3-1/2% for each 1,000 feet (300 meters) above sea level and

1% for each 10° F (5.6° C) above 77° F (25° C). It should

operate satisfactorily at an angle up to 15°.

SPECIFICATIONS

OWNER’S RESPONSIBILITIES

Follow the hourly or calendar intervals, whichever occurs

first.

More frequent service is required when operating in adverse

conditions noted below.

Clean if clogged. Replace if perforated or torn.

Service more often under dirty or dusty conditions.

General Recommendations

Regular maintenance will improve the performance and

extend the life of the pressure washer. See any Sears or

other qualified service dealer for service.

The pressure washer warranty does not cover items that

have been subjected to operator abuse or negligence. To

receive full value from the warranty, the operator must

maintain pressure washer as instructed in this manual

including proper storage as detailed in Storage.

Some adjustments will need to be made periodically to

properly maintain your pressure washer.

All service and adjustments should be made at least once

each season. Follow the requirements in the Maintenance

Schedule chart above.

NOTE: Once a year you should clean or replace the spark

plug and replace the air filter. A new spark plug and clean air

filter assure proper fuel-air mixture and help your engine run

better and last longer.

Pump Oil

DO NOT attempt any oil maintenance on this pump. The

pump is pre-lubricated and sealed from the factory, requiring

no additional maintenance for the life of the pump.

Emissions Control

Maintenance, replacement, or repair of the emissions

control devices and systems may be performed by any non-

road engine repair establishment or individual. However,

to obtain ”no charge” emissions control service, the work

must be performed by a qualified service dealer. See the

Emissions Warranty.

Before Each Use

1. Check engine oil level.

2. Clean debris.

3. Check water inlet screen for damage.

4. Check high pressure hose for leaks.

5. Check detergent siphoning hose/filter for damage.

6. Check gun and nozzle extension assembly for leaks.

7. Purge pump of air and contaminants.

PRESSURE WASHER MAINTENANCE

Clean Debris

Daily or before use, clean accumulated debris from pressure

washer. Keep linkage, spring and controls clean. Keep area

around and behind muffler free from any combustible debris.

Inspect cooling air slots and openings on the pressure

washer. These openings must be kept clean and

unobstructed.

Pressure washer parts should be kept clean to reduce the

risk of overheating and ignition of accumulated debris.

• Use a damp cloth to wipe exterior surfaces clean.

• Use a soft bristle brush to loosen caked on dirt, oil, etc.

• Use a vacuum cleaner to pick up loose dirt and debris.

Check and Clean Inlet Screen

Examine garden hose inlet screen. Clean if it is clogged or

replace if it is torn.

MAINTENANCE

First 5 Hours

• Change engine oil

Every 8 Hours or Daily

• Check/clean water inlet screen

• Check high pressure hose

• Check detergent siphoning hose

• Check spray gun and assembly for leaks

• Clean debris

• Check engine oil level

Every 25 Hours or Yearly

• Service air cleaner

Every 50 Hours or Yearly

• Change engine oil

• Service spark arrester

Every 100 Hours or Yearly

• Service spark plug

• Air cooling system

NOTICE

Improper treatment of pressure washer can damage it and

shorten its life.

• DO NOT insert any objects through cooling slots.

Check High Pressure Hose

High pressure hoses can develop leaks from wear, kinking,

or abuse. Inspect hose before each use. Check for cuts,

leaks, abrasions, bulging of cover, or damage or movement

of couplings. If any of these conditions exist, replace hose

immediately.

Check Detergent Siphoning Tube

Examine the filter on the detergent tube and clean if clogged.

The tube should fit tightly on the barbed fitting. Examine the

tube for leaks or tears. Replace the filter or tube if either is

damaged.

Check Gun and Nozzle Extension

Examine hose connection to spray gun and make sure it is

secure. Test trigger by pressing it and making sure it springs

back into place when you release it. Put safety latch in UP

position and test trigger. You should not be able to press

trigger. Replace spray gun immediately if it fails any of these

tests.

Nozzle Maintenance

A pulsing sensation felt while squeezing the spray gun trigger

may be caused by excessive pump pressure. The principal

cause of excessive pump pressure is a orifice clogged or

restricted with foreign materials, such as dirt, etc. To correct

the problem, immediately clean the orifice following these

instructions:

1. Shut off engine and turn off water supply.

2. ALWAYS point gun in a safe direction and squeeze spray

gun trigger to release retained high water pressure.

3. Remove nozzle extension from spray gun.

4. Twist nozzle clockwise to stream position. Using a 2mm

(5/64) allen wrench, remove orifice from end of nozzle

extension.

5. Use a small paper clip to free any foreign material

clogging or restricting orifice.

6. Using a garden hose, remove additional debris by back

flushing water through nozzle extension. Back flush

between 30 to 60 seconds. Turn adjustable nozzle

extension to stream spray and move nozzle from low to

high while flushing.

7. Reinstall orifice into nozzle extension. DO NOT

overtighten orifice with allen wrench.

8. Reconnect nozzle extension to spray gun.

9. Make sure garden hose is connected to water inlet.

Check that high pressure hose is connected to spray gun

and pump. Turn on water.

10. Engage trigger lock on spray gun and start engine

following instructions “How to Start Your Pressure

Washer”.

11. Test pressure washer by operating nozzle in high and

low positions.

O–Ring Maintenance

Purchase an O–Ring Repair Kit at your local Sears or by calling

1-800-4-MY-HOME (469-4663) or online at www.sears.ca. It is

not included with the pressure washer. This kit includes

replacement o-rings, rubber washer and water inlet filter. Refer to

the instruction sheet provided in the kit to service your unit’s

o-rings.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

• NEVER repair high pressure hose. Replace it.

• Replacement hose rating MUST exceed maximum pressure

rating of unit.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected,

which can cause injury.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction and squeeze spray

gun trigger, to release high pressure, every time you stop

engine. Engage trigger lock when not in use.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

• NEVER repair leaking connections with sealant of any kind.

Replace o-ring or seal.

ENGINE MAINTENANCE

Oil

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty

Certified oils for best performance. Other high-quality

detergent oils are acceptable if classified for service SF, SG,

SH, SJ or higher. DO NOT use special additives.

Outdoor temperatures determine the proper oil viscosity for

the engine. Use the chart to select the best viscosity for the

outdoor temperature range expected.

* Below 40°F (4°C) the use of SAE 30 will result in hard starting.

** Above 80°F (27°C) the use of 10W30 may cause increased oil

consumption. Check oil level more frequently.

NOTE: Synthetic oil meeting ILSAC GF-2, API

certification mark and API service symbol with

“SJ/CF ENERGY CONSERVING” or higher, is an

acceptable oil at all temperatures. Use of synthetic oil

does not alter required oil change intervals.

Checking Oil Level

Oil level should be checked prior to each use or at least every

8 hours of operation. Keep oil level maintained.

1. Make sure pressure washer is on a level surface.

2. Remove oil dipstick and wipe dipstick with clean cloth.

Replace and tighten dipstick. Remove and and check oil

level.

3. Verify oil is at “Full” mark on dipstick. Replace and

tighten dipstick.

Adding Engine Oil

1. Make sure pressure washer is on a level surface.

2. Check oil level as described in Checking Oil Level.

3. If needed, slowly pour oil into oil fill opening to the

“Full” mark on dipstick. DO NOT overfill.

4. Replace and tighten dipstick.

Changing Engine Oil

Change engine oil after the first 5 hours and every 50 hours

thereafter. If you are using your pressure washer under

extremely dirty or dusty conditions, or in extremely hot

weather, change oil more often.

KEEP OUT OF REACH OF CHILDREN. DON'T

POLLUTE. CONSERVE RESOURCES. RETURN

USED OIL TO COLLECTION CENTERS.

WARNING

Unintentional sparking can result in fire or

electric shock.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

PRESSURE WASHER

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

NOTICE

Overfilling with oil may cause the engine to not start, or

hard starting.

• DO NOT overfill.

• If over the FULL mark on dipstick, drain oil to reduce oil level to

FULL mark on dipstick.

CAUTION

Avoid prolonged or repeated skin contact with used motor

oil.

• Used motor oil has been shown to cause skin cancer in certain

laboratory animals.

• Thoroughly wash exposed areas with soap and water.

Change oil while engine is still warm from running, as

follows:

1. Drain fuel tank by running pressure washer until fuel

tank is empty.

2. Disconnect spark plug wire and keep it away from spark

plug.

3. Clean area around oil fill, remove oil fill cap/dipstick.

Wipe dipstick clean.

4. Tip your pressure washer to drain oil from oil fill into a

suitable container making sure you tip your unit away

from spark plug. When crankcase is empty, return

pressure washer to upright position.

5. Slowly pour recommended oil (about 18 oz.) into oil fill

opening. Pause to permit oil to settle. Fill to “Full” mark

on dipstick.

6. Wipe dipstick clean each time oil level is checked. DO

NOT overfill.

7. Replace and tighten dipstick.

8. Wipe up any remaining oil.

9. Reconnect spark plug wire to spark plug.

Service Air Cleaner

Your engine will not run properly and may be damaged if you

run it with a dirty air cleaner.

Service the air cleaner once every 25 hours of operation or

once each year, whichever comes first. Service more often if

operating under dirty or dusty conditions. Replacements are

available at your local Sears service center.

To service the air cleaner, follow these steps:

1. Remove screw (A).

2. Carefully remove air cleaner assembly to prevent debris

from falling into carburetor.

3. Take air cleaner assembly apart and clean all parts.

Wash foam air cleaner (B) in liquid detergent and water.

Squeeze dry in a clean cloth.

4. SATURATE foam air cleaner in engine oil and squeeze in

a clean cloth to remove excess oil.

5. Reinstall clean or new foam air cleaner in base (C).

6. Install air cleaner securely on carburetor with screw.

NOTE: You can purchase new air filter elements by calling

1-800-4-MY-HOME (469-4663).

Service Spark Plug

Service the spark plug every 100 hours of operation or

yearly, whichever occurs first.

1. Clean area around spark plug.

2. Remove and inspect spark plug.

3. Replace spark plug if electrodes are pitted, burned or

porcelain is cracked. Use the recommended replacement

plug. See Specifications.

4. Check electrode gap with wire feeler gauge and set spark

plug gap to .030 inch (.76 mm) if necessary.

5. Install spark plug and tighten firmly.

NOTE: You can purchase a new spark plug by calling

1-800-4-MY-HOME (469-4663).

Spark Arrester Service

Your engine is not factory-equipped with a spark arrester. In

some areas, it is illegal to operate an engine without a spark

arrester. Check local laws and regulations. A spark arrester is

available from your nearest Sears service center. If you need

to order a spark arrester, please call 1-800-4-MY-HOME

(469-4663).

The spark arrester must be serviced every 50 hours to keep it

functioning as designed.

If the engine has been running, the muffler will be very hot.

Allow the muffler to cool before servicing the spark arrester.

• Remove spark arrester screen for cleaning and inspection.

• Replace if screen is damaged.

Air Cooling System

Over time debris may accumulate in cylinder cooling fins and

cannot be observed without partial engine disassembly. For

this reason, we recommend you have a qualified Sears

service dealer clean the cooling system per recommended

intervals (see Maintenance Schedule). Equally important is to

keep top of engine free from debris. See Clean Debris.

AFTER EACH USE

Water should not remain in the unit for long periods of time.

Sediments or minerals can deposit on pump parts and

“freeze” pump action. Follow these procedures after every

use:

1. Shut off engine, turn off water supply, point gun in a

safe direction and squeeze trigger to relieve trapped

pressure,

engage trigger lock on spray gun and let engine

cool.

2. Disconnect hose from spray gun and high pressure

outlet on pump. Drain water from hose, gun, and nozzle

extension. Use a rag to wipe off the hose.

3. Empty pump of all pumped liquids by pulling recoil

handle about 6 times. This should remove most liquid in

pump.

4. Store unit in a clean, dry area.

5. If storing for more than 30 days see Long Term Storage

on next page.

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers, or other appliances that have pilot light or other ignition

source because they can ignite fuel vapors.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected,

which can cause injury.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction and squeeze spray

gun trigger, to release high pressure, every time you stop

engine. Engage trigger lock when not in use.

WARNING

Contact with muffler area can result in serious

burns.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (152 cm) of clearance on all sides of

pressure washer including overhead.

• Code of Federal Regulation (CFR) Title 36 Parks, Forests, and

Public Property require equipment powered by an internal

combustion engine to have a spark arrester, maintained in

effective working order, complying to USDA Forest service

standard 5100-1C or later revision. In the State of California a

spark arrester is required under section 4442 of the California

Public resources code. Other states may have similar laws.

Keep areas within heavy line clear of debris.

STORAGE

WINTER STORAGE

To protect the unit from freezing temperatures:

1. Follow steps 1-3 in the previous section After Each Use.

2. Use pump saver to treat pump. This minimizes freeze

damage and lubricates pistons and seals.

3. If pump saver is not available, connect a 3-foot section

of garden hose to water inlet adapter. Pour

RV–antifreeze (antifreeze without alcohol) into hose. Pull

recoil handle twice. Disconnect 3-foot hose.

4. Store unit in a clean, dry area.

LONG TERM STORAGE

If you do not plan to use the pressure washer for more than

30 days, you must prepare the engine and pump for long

term storage.

It is important to prevent gum deposits from forming in

essential fuel system parts such as the carburetor, fuel filter,

fuel hose or tank during storage. Also, experience indicates

that alcohol-blended fuels (called gasohol, ethanol or

methanol) can attract moisture, which leads to separation

and formation of acids during storage. Acidic gas can

damage the fuel system of an engine while in storage.

Protect Fuel System

Fuel Additive:

Fuel can become stale when stored over 30 days. Stale fuel

causes acid and gum deposits to form in the fuel system or

on essential carburetor parts. To keep fuel fresh, use Briggs

& Stratton FRESH START™ fuel stabilizer, available as a

liquid additive or a drip concentrate cartridge.

There is no need to drain gasoline from the engine if a fuel

stabilizer is added according to instructions. Run the engine

for 2 minutes to circulate the stabilizer throughout the fuel

system. The engine and fuel can then be stored up to

24 months.

If gasoline in the engine has not been treated with a fuel

stabilizer, it must be drained into an approved container. Run

the engine until it stops from lack of fuel. The use of a fuel

stabilizer in the storage container is recommended to

maintain freshness.

Change Oil

While engine is still warm, drain oil from crankcase. Refill

with recommended grade. See Changing Engine Oil.

Oil Cylinder Bore

• Remove spark plug and pour about 1/2 ounce (15 ml) of

clean engine oil into the cylinder.

• Install spark plug and pull starter handle slowly to

distribute oil.

Protect Pump

To protect the pump from damage caused by mineral

deposits or freezing, use PumpSaver to treat pump. This

prevents freeze damage and lubricates pistons and seals.

NOTE: PumpSaver is available as an optional accessory. It is

not included with the pressure washer. Contact your local

Sears service center to purchase PumpSaver.

To use PumpSaver, make sure the pressure washer is turned

off and disconnected from supply water. Read and follow all

instructions and warnings given on the PumpSaver container.

Other Storage Tips

1. DO NOT store fuel from one season to another unless it

has been treated as described in Protect Fuel System.

2. Replace fuel container if it starts to rust. Rust and/or dirt

in fuel can cause problems if it’s used with this unit.

3. Cover unit with a suitable protective cover that does not

retain moisture.

4. Store unit in a clean and dry area.

NOTICE

You must protect your unit from freezing temperatures.

• Failure to do so will permanently damage your pump and

render your unit inoperable.

• Freeze damage is not covered under warranty.

NOTICE

You must protect your unit from freezing temperatures.

• Failure to do so will permanently damage your pump and

render your unit inoperable.

• Freeze damage is not covered under warranty.

WARNING

Storage covers can be flammable.

• DO NOT place a storage cover over a hot pressure washer.

• Let equipment cool for a sufficient time before placing the

cover on the equipment.

La page charge ...

Simplicity 020322-0 Manuel utilisateur

Marque: Simplicity

Modèle: 020322-0

Catégorie: Nettoyeurs haute pression

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Simplicity 020322-0 User manual

Simplicity 020322-0 Manuel utilisateur

Simplicity 020322-0 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents