Simplicity 020248-1 Manuel utilisateur

Catégorie
Nettoyeurs haute pression
Taper
Manuel utilisateur
PRESSURE WASHER
3.75 HORSEPOWER
2,000 PSI
2.0 GPM
PRESSURE WASHER
CUSTOMER HELPLINE
1-800-222-3136
Model No. 580.676641
HOURS: Mon. - Fri. 8 a.m. to 5 p.m. (CT)
Part No. 197195GS Draft B (04/04/2006)
Sears Canada, Inc.
Visit our Craftsman website: www.sears.ca
Operators Manual
Safety
Assembly
Operation
Maintenance
Parts
Français
WARNING
Before using this product, read this
manual and follow all Safety Rules and
Operating Instructions.
AVERTISSEMENT
Avant d’utiliser ce produit, veuillez lire
le manuel et suivre toutes les directives
relatives à la sécurité et à l’utilisation.
Read this manual carefully and become
familiar with your pressure washer. Know its
applications, its limitations, and any hazards
involved.
The safety alert symbol ( ) is used with a signal
word (DANGER, CAUTION, WARNING), a pictorial
and/or a safety message to alert you to hazards.
DANGER indicates a hazard which, if not avoided, will
result in death or serious injury. WARNING indicates a
hazard which, if not avoided, could result in death or
serious injury. CAUTION indicates a hazard which, if
not avoided, might result in minor or moderate injury.
CAUTION, when used without the alert symbol,
indicates a situation that could result in equipment
damage. Follow safety messages to avoid or reduce
the risk of injury or death.
Hazard Symbols and Meanings
2
TABLE OF CONTENTS
WARRANTY
LIMITED ONE YEAR WARRANTY ON CRAFTSMAN PRESSURE WASHER
For one year from the date of purchase, when this CRAFTSMAN® Pressure Washer is maintained and operated
according to the instructions in the operator’s manual, Sears will repair, free of charge, any defect in material
and workmanship.
If this pressure washer is used for commercial purposes, this warranty applies for only 90 days from the date of
purchase.
If this pressure washer is used for rental purposes, this warranty applies for only 30 days after date of purchase.
This warranty does not cover:
Expendable items such as spark plugs and air filters, which become worn during normal use.
Repairs necessary because of operator abuse or negligence, including damage resulting from no water being
supplied to pump or failure to maintain the equipment according to the instructions contained in the
operator’s manual.
WARRANTY SERVICE IS AVAILABLE BY RETURNING THE PRESSURE WASHER TO THE NEAREST
SEARS SERVICE CENTER OR DEALER IN CANADA.
This warranty gives you specific legal rights and you may also have other rights, which vary from province to
province.
Sears Canada, Inc.
SAFETY RULES
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
Fire
Explosion
Operator’s Manual
Hot Surface
Moving Parts
Electrical Shock
Slippery Surface
Fall
Kickback
Flying Objects
Fluid Injection
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
FEATURES & CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . 5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-12
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-18
STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-20
TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
HOW TO ORDER PARTS. . . . . . . . . . . . . . . . . . . . . . . . . 23
REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . 24-29
EMISSION CONTROL WARRANTY . . . . . . . . . . . . . . 30-31
FRANÇAIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32-56
© Sears Brands, LLC
Toxic Fumes
3
The engine exhaust from this product contains
chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm.
WARNING
Operate pressure washer ONLY outdoors.
Keep exhaust gas from entering a confined area through
windows, doors, ventilation intakes or other openings.
DO NOT operate pressure washer inside any building or
enclosure, even if doors or windows are open.
Use a respirator or mask whenever there is a chance
that vapors may be inhaled.
Read all instructions packed with mask so you are certain
mask will provide necessary protection against inhaling
harmful vapors.
Running engine gives off carbon monoxide,
an odorless, colorless, poison gas.
Breathing carbon monoxide can cause
nausea, fainting or death.
Some chemicals or detergents may be
harmful if inhaled or ingested, causing
severe nausea, fainting or poisoning.
WARNING
Keep spray nozzle between 8 to 24 inches away from
cleaning surface.
Operate this unit on a stable surface.
Cleaning area should have adequate slopes and drainage
to reduce possibility of falls due to slippery surfaces.
Be extremely careful if you must use pressure washer from a
ladder, scaffolding or any other relatively unstable location.
Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when gun kicks back.
Use of pressure washer can create puddles
and slippery surfaces.
High pressure spray could cause you to fall
if you are too close to the cleaning surface.
WARNING
WHEN ADDING OR DRAINING FUEL
Turn pressure washer OFF and let it cool at least 2
minutes before removing fuel cap. Loosen cap slowly to
relieve pressure in tank.
Fill or drain fuel tank outdoors.
DO NOT overfill tank. Allow space for fuel expansion.
If fuel spills, wait until it evaporates before starting
engine.
Keep fuel away from sparks, open flames, pilot lights,
heat, and other ignition sources.
DO NOT light a cigarette or smoke.
WHEN STARTING EQUIPMENT
Ensure spark plug, muffler, fuel cap and air cleaner are
in place.
DO NOT crank engine with spark plug removed.
WHEN OPERATING EQUIPMENT
Do not tip engine or equipment at angle which causes
fuel to spill.
DO NOT spray flammable liquids.
WHEN TRANSPORTING OR REPAIRING EQUIPMENT
Transport/repair with fuel tank EMPTY or with fuel shutoff
valve OFF.
Disconnect spark plug wire.
WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN
TANK
Store away from furnaces, stoves, water heaters, clothes
dryers or other appliances that have pilot light or other
ignition source because they can ignite fuel vapors.
Fuel and its vapors are extremely flammable
and explosive.
Fire or explosion can cause severe burns or
death.
WARNING
NEVER aim spray gun at people, animals or plants.
DO NOT allow CHILDREN to operate pressure washer.
NEVER repair high pressure hose. Replace it.
NEVER repair leaking connections with sealant of any
kind. Replace o-ring or seal.
Keep high pressure hose connected to pump and spray
gun while system is pressurized.
ALWAYS point gun in safe direction and squeeze spray
gun trigger, to release high pressure, every time you stop
engine. Engage trigger lock when not in use.
The high pressure stream of water that this
equipment produces can pierce skin and its
underlying tissues, leading to serious injury
and possible amputation.
Spray gun traps high water pressure, even
when engine is stopped and water is
disconnected, which can cause injury.
WARNING
DO NOT wear loose clothing, jewelry or anything that
may be caught in starter or other rotating parts.
Tie up long hair and remove jewelry.
Starter and other rotating parts can entangle
hands, hair, clothing, or accessories.
WARNING
Keep water spray away from electric wiring or fatal
electric shock may result.
Spray contact with electrical wiring can
result in electrocution.
WARNING
4
If you have questions about intended use, ask dealer or
contact Sears.
NEVER operate units with broken or missing parts, or
without protective housing or covers.
DO NOT by–pass any safety device on this machine.
Before starting pressure washer in cold weather, check
all parts of the equipment to be sure ice has not formed
there.
NEVER move machine by pulling on high pressure hose.
Use handle provided on unit.
Check fuel system for leaks or signs of deterioration,
such as chafed or spongy hose, loose or missing
clamps, or damaged tank or cap. Correct all defects
before operating pressure washer.
This equipment is designed to be used with Sears
authorized parts ONLY. If equipment is used with parts
that DO NOT comply with minimum specifications, user
assumes all risks and liabilities.
Improper treatment of pressure washer can
damage it and shorten its life.
CAUTION
DO NOT secure spray gun in open position.
DO NOT leave spray gun unattended while machine is
running.
NEVER use a spray gun which does not have a trigger
lock or trigger guard in place and in working order.
Always be certain spray gun, nozzles and accessories
are correctly attached.
A pressure washer produces a high pressure spray
which increases risk of injury and damage to unit.
CAUTION
DO NOT point spray gun at glass when in jet spray mode.
NEVER aim spray gun at plants.
High pressure spray may damage fragile items
including glass.
CAUTION
DO NOT tamper with governed speed.
DO NOT operate pressure washer above rated pressure.
Excessively high or low operating speeds increase
risk of injury and damage to pressure washer.
CAUTION
WHEN ADJUSTING OR MAKING REPAIRS TO YOUR
PRESSURE WASHER
Disconnect the spark plug wire from the spark plug and
place the wire where it cannot contact spark plug.
WHEN TESTING FOR ENGINE SPARK
Use approved spark plug tester.
DO NOT check for spark with spark plug removed.
Unintentional sparking can result in fire or
electric shock.
WARNING
DO NOT touch hot surfaces and avoid hot exhaust gases.
Allow equipment to cool before touching.
Keep at least 5 ft. (152 cm) clearance on all sides of
pressure washer including overhead.
Code of Federal Regulation (CFR) Title 36 Parks,
Forests, and Public Property require equipment powered
by an internal combustion engine to have a spark
arrester, maintained in effective working order, complying
to USDA Forest service standard 5100-1C or later
revision. In the State of California a spark arrester is
required under section 4442 of the California Public
resources code. Other states may have similar laws.
Running engines produce heat.
Temperature of muffler and nearby areas
can reach or exceed 150°F (65°C).
Severe burns can occur on contact.
Exhaust heat/gases can ignite combustibles,
structures or damage fuel tank causing a fire.
WARNING
Always wear safety goggles when using this equipment
or in vicinity of where equipment is in use.
Before starting the pressure washer, be sure you are
wearing adequate safety goggles.
High pressure spray can cause paint chips
or other particles to become airborne.
WARNING
ALWAYS point gun in safe direction and squeeze spray
gun trigger, to release pressure and avoid kickback each
time, before starting engine. Engage trigger lock when
not in use.
When starting engine, pull cord slowly until resistance is
felt and then pull rapidly to avoid kickback.
After each starting attempt, where engine fails to run,
always point gun in safe direction and squeeze spray
gun trigger to release high pressure.
Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when gun kicks back.
Rapid retraction of starter cord (kickback)
will pull hand and arm toward engine faster
than you can let go.
Broken bones, fractures, bruises or sprains
could result.
WARNING
5
KNOW YOUR PRESSURE WASHER
Read the operator’s manual and safety rules before operating your pressure washer.
Compare the illustrations with your pressure washer to familiarize yourself with the locations of various
controls and adjustments. Save this manual for future reference.
FEATURES AND CONTROLS
Detergent Pick–Up
Tube and Filter
Recoil Starter
Oil Fill Cap and Dipstick
Air Filter
Fuel Cap
High Pressure Outlet
Water Inlet
Pump equipped with
Automatic Cool Down System
Throttle Control
Lever
Adjustable Nozzle (not shown) – Adjust for high or
low pressure; narrow or fan spray.
Air Filter — Protects engine by filtering dust and
debris out of intake air.
Automatic Cool Down System — Cycles water
through pump when water reaches 125°-155°F. Warm
water will discharge from pump onto ground. This
system prevents internal pump damage.
Detergent Pick–Up Tube and Filter – Used to siphon
detergent from chemical bottle to the low pressure
water stream.
Fuel Cap – Fill fuel tank with regular unleaded fuel
here.
High Pressure Hose (not shown) – Connect one end
to the spray gun and other end to the high pressure
outlet.
High Pressure Outlet — Connection for high
pressure hose.
Nozzle Extension (not shown) — Attach to spray
gun to use adjustable nozzle.
Oil Fill Cap and Dipstick – Check and fill engine with
oil here. See page 16 for oil recommendations and
filling instructions.
Primer Bulb — Prepares a cold engine for starting.
Pump — Develops high water pressure.
Recoil Starter — Used for starting the engine
manually.
Spray Gun (not shown) – Controls the application of
water onto cleaning surface with trigger device.
Includes trigger lock.
Throttle Control Lever – Sets engine in starting
mode for recoil starter and stops running engine.
Water Inlet — Connection for garden hose.
Primer Bulb
Your pressure washer requires some assembly and is
ready for use only after it has been properly serviced
with the recommended oil and fuel.
If you have any problems with the assembly of
your pressure washer, please call the pressure
washer helpline at 1-800-222-3136.
IMPORTANT: Any attempt to run the engine before it
has been serviced with the recommended oil will result
in an engine failure.
Unpack the Pressure Washer
1. Remove everything from carton except pressure
washer.
2. Open carton completely by cutting each corner
from top to bottom.
3. Remove pressure washer from carton.
CARTON CONTENTS
Check all contents. If any parts are missing or damaged,
call the pressure washer helpline at 1-800-222-3136.
The main unit
Handle
High pressure hose
Spray gun
Nozzle extension with adjustable nozzle
Turbo nozzle
Wheel kit
Safety goggles
Engine oil
Parts bag (which includes items listed below)
Operator’s manual
Become familiar with each piece before assembling
the pressure washer. Compare contents against the
view on page 5. If any parts are missing or damaged,
call the pressure washer helpline at 1-800-222-3136.
ASSEMBLING YOUR PRESSURE
WASHER
Your Craftsman pressure washer was mostly
assembled at the factory. However, you will need to
perform these tasks before you can operate your
pressure washer:
1. Attach handle to main unit.
2. Install wheel kit.
3. Add oil to engine crankcase.
4. Add fuel to fuel tank.
5. Connect high pressure hose to spray gun and pump.
6. Connect water supply to pump.
Attach Handle
1. Place plastic adapters in hinges on handle
extension as shown.
NOTE: Make sure lip on plastic adapters is facing up
in hinges.
2. Clamp handle extension onto pressure washer
handle and insert T-bolts into holes of clamp.
Tighten by hand.
Install Wheel Kit
The wheel kit is designed to greatly improve the
portability of your pressure washer.
NOTE: Wheel kit is not intended for over-the-road use.
Install the wheel kit as follows:
1. Place the bottom of the pressure washer frame on a
flat, even surface, such as blocks to ease assembly.
2. Spread axle brackets apart and place over front
vibration mounts on the pressure washer frame as
shown.
3. Squeeze axle brackets back to original shape.
6
ASSEMBLY
7
4. Slide axle through holes in both axle brackets, as
shown.
5. With raised hub inward, slide wheels over axle on
each side of pressure washer frame.
6. Install retaining clips into grooves on axle to retain
wheels.
7. Remove the temporary blocks.
Add Engine Oil
CAUTION! Any attempt to crank or start the engine
before it has been properly serviced with the
recommended oil may result in an engine failure.
1. Place pressure washer on a level surface.
2. Clean area around oil fill and remove oil dipstick.
3. Using oil funnel (optional), slowly pour entire
contents of provided oil bottle (18 oz.) into oil fill
opening.
4. Replace oil dipstick and fully tighten.
NOTE: See the section “Oil” on page 16 to review oil
recommendations.
Add Fuel
NOTE: This engine is certified to operate on gasoline.
Exhaust Emission Control System: EM (Engine
Modifications).
1. Use clean, fresh, regular UNLEADED fuel with a
minimum of 85 octane with equipment. DO NOT
use fuel which contains Methanol. DO NOT mix oil
with fuel.
2. Clean area around fuel fill cap, remove cap.
3. Slowly add regular unleaded fuel to fuel tank. Be
careful not to overfill. Allow about 1.5" of tank
space for fuel expansion, as shown here.
4. Install fuel cap and wait for any spilled fuel to
evaporate.
CAUTION! Alcohol-blended fuels (called gasohol,
ethanol or methanol) can attract moisture, which leads
to separation and formation of acids during storage.
Acidic gas can damage the fuel system of an engine
while in storage.
To avoid engine problems, the fuel system should be
emptied before storage of 30 days or longer. Drain the
fuel tank, start the engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel next season.
See “Storage” on pages 19-20 for additional information.
NEVER use engine or carburetor cleaner products in
the fuel tank as permanent damage may occur.
WHEN ADDING FUEL
Turn pressure washer OFF and let it cool at least 2
minutes before removing fuel cap. Loosen cap slowly to
relieve pressure in tank.
Fill or drain fuel tank outdoors.
DO NOT overfill tank. Allow space for fuel expansion.
If fuel spills, wait until it evaporates before starting engine.
Keep fuel away from sparks, open flames, pilot lights,
heat, and other ignition sources.
DO NOT light a cigarette or smoke.
Fuel and its vapors are extremely flammable
and explosive.
Fire or explosion can cause severe burns or
death.
WARNING
Fuel
Tank
1.5” Air Space
8
Connect Hose and Water Supply to Pump
IMPORTANT: To avoid pump damage, you must
assemble the nozzle extension to the spray gun and
attach all hoses before you start the engine.
1. Uncoil high pressure hose and attach one end of
hose to base of spray gun. Tighten by hand.
2. Attach other end of high pressure hose to high
pressure outlet on pump. Tighten by hand.
3. Before connecting garden hose to water inlet,
inspect inlet screen. Clean screen if it contains
debris or have it replaced if damaged. Refer to
section “O-Ring Maintenance” if inlet screen is
damaged. DO NOT run pressure washer if inlet
screen is damaged.
4. Run water through garden hose for 30 seconds to
flush it of debris. Turn off water.
IMPORTANT: DO NOT siphon standing water for the
water supply. Use ONLY cold water (less than 100°F).
5. Connect garden hose (not to exceed 50 feet in
length) to water inlet. Tighten by hand.
6. Turn ON water, point gun in a safe direction and
squeeze trigger to purge pump system of air and
impurities.
CHECKLIST BEFORE STARTING
ENGINE
Review the unit to ensure you have performed all of
the following:
1. Check that oil has been added to proper level in
engine crankcase.
2. Add proper fuel to fuel tank.
3. Check for properly tightened hose connections
(high pressure and water supply) and there are no
kinks, cuts, or damage to high pressure hose.
4. Provide proper water supply (not to exceed 100°F).
5. Be sure to read “Safety Rules” and “Operation”
sections before using pressure washer.
6. If starting unit after storage, see “Storage” section
on pages 19-20.
Inspect inlet
screen. DO
NOT use if
damaged;
clean if dirty.
CAUTION
Damage to equipment resulting from failure to follow
this instruction will void warranty.
There MUST be at least ten feet of unrestricted garden
hose between the pressure washer inlet and any flow
shut off device, such as a ‘Y’ shut-off connector or
other convenience-type water shut-off valve.
Always wear safety goggles when using this equipment
or in vicinity of where equipment is in use.
Before starting the pressure washer, be sure you are
wearing adequate safety goggles.
High pressure spray can cause paint chips
or other particles to become airborne.
WARNING
9
HOW TO USE YOUR PRESSURE
WASHER
If you have any problems operating your pressure
washer, please call the pressure washer helpline at
1-800-222-3136.
Pressure Washer Location
Pressure Washer Clearance
Place pressure washer in a well ventilated area, which
will allow for removal of deadly exhaust gas. DO NOT
place pressure washer where exhaust gas could
accumulate and enter inside or be drawn into a
potentially occupied building. Ensure exhaust gas is
kept away from any windows, doors, ventilation
intakes or other openings that can allow exhaust gas
to collect in a confined area. Prevailing winds and air
currents should be taken into consideration when
positioning pressure washer.
To Start Your Pressure Washer
To start your engine-powered pressure washer for the
first time, follow these instructions step-by-step. This
starting information also applies whenever you start
the engine after you have let the pressure washer sit
idle for at least a day.
1. Place pressure washer near an outside water
source capable of supplying water at a flow rate
greater than 3.0 gallons per minute and no less than
20 PSI at pressure washer end of garden hose.
2. Check that high pressure hose is tightly connected
to spray gun and pump. See “Assembling Your
Pressure Washer” for illustrations.
3. Make sure unit is in a level position.
4. Connect garden hose to water inlet on pressure
washer pump.
5. Turn ON water, point gun in a safe direction and
squeeze trigger to purge pump system of air and
impurities.
6. Attach nozzle extension to spray gun. Tighten by
hand.
7. Engage safety latch to spray gun trigger.
Safety Latch
OPERATION
CAUTION
Damage to equipment will result from failure to follow
this instruction.
DO NOT run the pump without the water supply
connected and turned on.
Exhaust Port
Typical Pressure
Washer Shown
Operate pressure washer ONLY outdoors.
Keep exhaust gas from entering a confined area through
windows, doors, ventilation intakes or other openings.
DO NOT operate pressure washer inside any building or
enclosure, even if doors or windows are open.
Running engine gives off carbon monoxide,
an odorless, colorless, poison gas.
Breathing carbon monoxide can cause
nausea, fainting or death.
WARNING
Keep at least 5 ft. (152 cm) clearance on all sides of
pressure washer including overhead.
Exhaust heat/gases can ignite combustibles,
structures or damage fuel tank causing a fire.
WARNING
10
8. Move throttle lever to “Fast” position, shown here
as a rabbit.
NOTE: For a warm engine, be sure the throttle lever is
in the “Fast” position.
To start the engine for the very first time:
9. Make sure throttle lever is in “Fast” position
(indicated on the engine as a rabbit).
10. Push primer bulb firmly 5 times, waiting 2 seconds
between each push.
To start engine thereafter:
9. Make sure throttle lever is in “Fast” position
(indicated on the engine as a rabbit).
10. Press primer bulb firmly 3 times, waiting
2 seconds between each push. For a warm
engine, DO NOT press primer bulb.
11. When starting engine, position yourself as
recommended and grasp starter grip handle and
pull slowly until you feel some resistance. Then
pull rapidly to start engine.
12. Return starter grip handle slowly. DO NOT let rope
“snap back” against starter.
NOTE: Always keep the throttle lever in the “Fast
position when operating the pressure washer.
How to Stop Your Pressure Washer
1. Let engine idle for two minutes.
2. Move throttle lever on engine to “Stop” position.
3. ALWAYS point gun in a safe direction and
squeeze spray gun trigger to release retained high
water pressure.
Throttle
Lever in
STOP
position
Stop
Fast
ALWAYS point gun in safe direction and squeeze spray
gun trigger, to release pressure and avoid kickback each
time, before starting engine.
When starting engine, pull cord slowly until resistance is
felt and then pull rapidly to avoid kickback.
After each starting attempt, where engine fails to run,
always point gun in safe direction and squeeze spray
gun trigger to release high pressure.
Rapid retraction of starter cord (kickback)
will pull hand and arm toward engine faster
than you can let go.
Broken bones, fractures, bruises or sprains
could result.
WARNING
Always use handle to lift equipment.
NEVER pull on hoses to move equipment.
Avoid fire from equipment tip over.
CAUTION
DO NOT touch hot surfaces and avoid hot exhaust gases.
Allow equipment to cool before touching.
Keep at least 5 ft. (152 cm) clearance on all sides of
pressure washer including overhead.
Code of Federal Regulation (CFR) Title 36 Parks,
Forests, and Public Property require equipment powered
by an internal combustion engine to have a spark
arrester, maintained in effective working order, complying
to USDA Forest service standard 5100-1C or later
revision. In the State of California a spark arrester is
required under section 4442 of the California Public
resources code. Other states may have similar laws.
Running engines produce heat.
Temperature of muffler and nearby areas
can reach or exceed 150°F (65°C).
Severe burns can occur on contact.
Exhaust heat/gases can ignite combustibles,
structures or damage fuel tank causing a fire.
WARNING
11
IMPORTANT: Spray gun traps high water pressure,
even when engine is stopped and water is
disconnected.
4. Engage trigger lock on spray gun when not in use.
How To Use the Adjustable Nozzle
You now should know how to START your pressure
washer and how to STOP it. The information in this
section will tell you how to adjust the spray pattern
and apply detergent or other cleaning chemicals.
On the end of your spray gun is a nozzle handle that
can adjust the spray pressure and the spray pattern.
1. Sliding nozzle forward and back adjusts spray
pressure.
2. Point nozzle toward ground, disengage trigger
lock, and press trigger to test pattern.
3. Rotating nozzle adjusts spray pattern from a
narrow pattern to a fan pattern.
4. For most effective cleaning, keep spray nozzle
between 8 to 24 inches away from cleaning
surface.
5. If you get spray nozzle too close, especially using
high pressure mode, you may damage the surface
being cleaned.
6. DO NOT get closer than 6 inches when cleaning
tires.
Using the Turbo Nozzle
The turbo nozzle rotates the high pressure stream in a
rapid circular pattern. The high pressure spray is most
effective when the tip of the nozzle extension is held
between 8 to 24 inches from the surface being cleaned.
To attach the turbo nozzle to the spray gun:
1. Engage trigger lock on spray gun trigger.
2. Remove the nozzle extension from the spray gun,
if attached.
NEVER adjust spray pattern when spraying.
NEVER put hands in front of nozzle to adjust spray pattern.
A pressure washer produces a high pressure spray
which increases risk of injury and damage to unit.
CAUTION
Keep high pressure hose connected to pump and spray
gun while system is pressurized.
ALWAYS point gun in safe direction and squeeze spray
gun trigger, to release high pressure, every time you stop
engine. Engage trigger lock when not in use.
The high pressure stream of water that this
equipment produces can pierce skin and its
underlying tissues, leading to serious injury
and possible amputation.
Spray gun traps high water pressure, even
when engine is stopped and water is
disconnected, which can cause injury.
WARNING
Slide nozzle backward for
high pressure mode.
Slide nozzle forward for low
pressure mode and
detergent application.
Twist nozzle counter-
clockwise for fan pattern.
Twist nozzle clockwise for
narrow spray pattern.
CAUTION
Always make sure the surface you will clean will not be
damaged by the high pressure spray by testing in a
hidden area.
The turbo nozzle produces an extremely high
pressure spray which is capable of removing paint
and cutting holes through surfaces if held too close.
12
3. Attach the turbo nozzle extension to spray gun.
Tighten by hand.
4. Disengage trigger lock on spray gun trigger.
5. Always start the turbo nozzle at a distance,
gradually getting closer to the surface until you get
the cleaning force you want.
NOTE: Detergent cannot be applied with turbo nozzle.
Applying Detergent with Adjustable Nozzle
IMPORTANT: Use detergents designed specifically for
pressure washers. Household detergents could
damage the pump.
To apply detergent, follow these steps:
1. Review use of adjustable nozzle.
2. Prepare detergent solution as required by job.
3. Place filter end of detergent siphoning tube into
detergent container.
4. Slide adjustable nozzle forward to low pressure
mode. Detergent cannot be applied with nozzle in
high pressure position.
5. Make sure garden hose is connected to water
inlet. Check that high pressure hose is connected
to spray gun and pump. Start engine.
6. Apply detergent to a dry surface, starting from
bottom and working up.
7. Allow detergent to “soak in” for 3-5 minutes before
rinsing. Reapply as needed to prevent surface
from drying.
8. For washing, start at lower portion of area to be
washed and work upward, using long, even,
overlapping strokes.
IMPORTANT: You must flush the chemical injection
system after each use by placing the filter into a clean
bucket of water and running the pressure washer in
low pressure for 1-2 minutes.
Pressure Washer Rinsing
For Rinsing:
1. Slide nozzle backward to high pressure, press
trigger and wait for detergent to clear.
NOTE: You can also stop detergent flow by removing
detergent siphoning tube from container.
2. Keep spray gun a safe distance from area you
plan to spray.
3. Apply a high pressure spray to a small area, then
check surface for damage. If no damage is found,
it is okay to continue cleaning.
4. Start at top of area to be rinsed, working down
with same overlapping strokes as you used for
washing and applying detergent.
Cleaning Detergent Siphoning Tube
If you used the detergent siphoning tube, you must
flush it with clean water before stopping the engine.
1. Place detergent siphoning tube/filter in a bucket
full of clean water.
2. Engage trigger lock on spray gun.
3. Slide adjustable nozzle forward to low pressure
position.
4. Flush for 1-2 minutes.
5. Shut off engine.
6. ALWAYS point gun in a safe direction and
squeeze spray gun trigger to release retained high
water pressure.
IMPORTANT: Spray gun traps high water pressure,
even when engine is stopped and water is disconnected.
Automatic Cool Down System
(Thermal Relief)
If you run the engine on your pressure washer for
3-5 minutes without pressing the trigger on the spray
gun, circulating water in the pump can reach
temperatures above 125°F (51°C). The system
engages to cool the pump by discharging the warm
water onto the ground.
CAUTION
Starting the engine without all the hoses connected and
without the water turned ON will damage the pump.
Damage to equipment resulting from failure to follow this
instruction will void warranty.
You must attach all hoses before you start the engine.
CAUTION
When inserting the filter into a detergent solution bottle,
route the tube so as to keep it from inadvertently
contacting the hot muffler.
Keep the detergent siphoning tube from coming in
contact with the hot muffler.
Keep spray nozzle between 8 to 24 inches away from
cleaning surface.
Operate this unit on a stable surface.
Be extremely careful if you must use the pressure
washer from a ladder, scaffolding or any other relatively
unstable location.
Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when gun kicks back.
High pressure spray could cause you to fall
if you are too close to the cleaning surface.
WARNING
13
ENGINE TECHNICAL INFORMATION
This is a single cylinder, L-head, air cooled engine. It
is a low emissions engine.
In the State of California, Model Series 90000 engines
are certified by the California Air Resources Board to
meet emissions standards for 125 hours. Such
certification does not grant the purchaser, owner or
operator of this engine any additional warranties with
respect to the performance or operational life of this
engine. The engine is warranted solely according to
the product and emissions warranties stated
elsewhere in this manual.
Power Ratings
The power ratings for an individual engine model are
initially developed by starting with SAE (Society of
Automotive Engineers) code J1940 (Small Engine
Power & Torque Rating Procedure) (Revision 2002-
05). Given both the wide array of products on which
our engines are placed, and the variety of
environmental issues applicable to operating the
equipment, it may be that the engine you have
purchased will not develop the rated horsepower when
used in a piece of power equipment (actual “on-site”
power). This difference is due to a variety of factors
including, but not limited to, the following: differences
in altitude, temperature, barometric pressure, humidity,
fuel, engine lubrication, maximum governed engine
speed, individual engine to engine variability, design of
the particular piece of power equipment, the manner in
which the engine is operated, engine run-in to reduce
friction and clean out of combustion chambers,
adjustments to the valves and carburetor, and other
factors. The power ratings may also be adjusted
based on comparisons to other similar engines utilized
in similar applications, and will therefore not
necessarily match the values derived using the
foregoing codes.
PRODUCT SPECIFICATIONS
Pressure Washer Specifications
Pressure . . . . . . . . . . . . . . . . . . 2,000 PSI
Flow Rate . . . . . . . . . . . . . . . . . 2.0 GPM
Chemical Mix. . . . . . . . . . . . . . . Use as directed
Water Supply Temperature. . . . Not to exceed 100°F
Shipping Weight . . . . . . . . . . . . 48 lbs.
Engine Specifications
Rated Horsepower . . . . . . . . . . . . 3.75 at 3600 rpm
Bore . . . . . . . . . . . . . . . . . . . . . . . 2.562 in. (65.09 mm)
Stroke . . . . . . . . . . . . . . . . . . . . . . 1.75 in. (44.45 mm)
Displacement . . . . . . . . . . . . . . . . 9.02 in. (147.8 cc)
Spark Plug
Type: . . . . . . . . . . . . . . . . . . . . . Champion RJ-19LM or
Equivalent
Set Gap To: . . . . . . . . . . . . . . . 0.030inch (0.76mm)
Armature Air Gap: . . . . . . . . . . . . 0.006-0.010 in.
(0.15-0.25mm)
Valve clearance with valve springs installed and piston 1/4 in.
(6 mm) past top dead center (check when engine is cold).
Intake . . . . . . . . . . . . . . . . . . . . . . 0.005-0.007 in.
(0.13-0.18 mm)
Exhaust . . . . . . . . . . . . . . . . . . . . 0.007-0.009 in.
(0.18-0.23 mm)
Fuel Capacity . . . . . . . . . . . . . . . . 1.0 Quarts
Oil Type:
Above 40° F . . . . . . . . . . . . . . . SAE 30
Below 40° F . . . . . . . . . . . . . . . SAE 5W-30 or 10W-30
NOTE: For practical operation, the horsepower
loading should not exceed 85% of rated horsepower.
Engine power will decrease 3-1/2% for each
1,000 feet (300 meters) above sea level and 1% for
each 10° F (5.6° C) above 77° F (25° C). It will
operate satisfactorily at an angle up to 15°.
SPECIFICATIONS
14
GENERAL RECOMMENDATIONS
Regular maintenance will improve the performance
and extend the life of the pressure washer. See any
authorized Sears dealer for service.
The pressure washer warranty does not cover items
that have been subjected to operator abuse or
negligence. To receive full value from the warranty,
the operator must maintain pressure washer as
instructed in this manual including proper storage as
detailed in “Storage” on pages 19-20.
Some adjustments will need to be made periodically to
properly maintain your pressure washer.
All service and adjustments should be made at least
once each season. Follow the requirements in the
“Maintenance Schedule” chart above.
NOTE: Once a year you should clean or replace the
spark plug and replace the air filter. A new spark plug
and clean air filter assure proper fuel-air mixture and
help your engine run better and last longer.
EMISSION CONTROL
Maintenance, replacement or repair of the emission
control devices and systems may be performed by any
non-road engine repair establishment or individual.
BEFORE EACH USE
1. Check engine oil level.
2. Check water inlet screen for damage.
3. Check in-line filter for debris.
4. Check high pressure hose for leaks.
5. Check chemical filters for damage.
6. Check gun and nozzle extension assembly for
leaks.
7. Purge pump of air and contaminants.
PRESSURE WASHER
MAINTENANCE
Clean Debris
Daily or before use, clean accumulated debris from
pressure washer. Keep linkage, spring and controls
clean. Keep area around and behind muffler free from
any combustible debris.
MAINTENANCE
OWNER’S RESPONSIBILITIES
Follow the hourly or calendar intervals, whichever occurs first.
More frequent service is required when operating in adverse conditions noted below.
¹ Clean if clogged. Replace if perforated or torn.
² Change oil after the first (5) operating hours and every 50 hours or yearly thereafter.
Change sooner when operating under dirty or dusty conditions.
³ Replace more often under dirty or dusty conditions.
MAINTENANCE SCHEDULE
FILL IN DATES AS YOU
COMPLETE REGULAR SERVICE
OPERATING INTERVALS
SERVICE DATES
MAINTENANCE TASK
Before
Each Use
Every 25
Hours or
Yearly
Every 50
Hours or
Yearly
Every 100
Hours or
Yearly
100-300
Hours
PRESSURE WASHER
Check/clean water inlet screen
Check high pressure hose X
Check detergent hose X
Check spray gun and assembly for leaks X
Purge pump of air and contaminants X
Prepare pump for storage below 32°F See Storage on pages 19-20.
ENGINE
Check oil level
X
Clean debris X
Change engine oil
Service air cleaner
Service spark plug X
Service spark arrester X
Clean cooling system
Clean combustion chamber X
Prepare for storage If unit is to remain idle for longer than 30 days.
15
Pressure washer parts should be kept clean to reduce the
risk of overheating and ignition of accumulated debris.
Use a damp cloth to wipe exterior surfaces clean.
Use a soft bristle brush to loosen caked on dirt, oil,
etc.
Use a vacuum cleaner to pick up loose dirt and debris.
Use low pressure air (not to exceed 25 psi) to blow
away dirt. Inspect cooling air slots and openings on
the pressure washer. These openings must be kept
clean and unobstructed.
Check and Clean Inlet Screen
Examine garden hose inlet screen. Clean if it is
clogged or replace if it is torn.
Check High Pressure Hose
High pressure hoses can develop leaks from wear,
kinking, or abuse. Inspect hose before each use.
Check for cuts, leaks, abrasions, bulging of cover, or
damage or movement of couplings. If any of these
conditions exist, replace hose immediately.
Check Gun and Nozzle Extension
Examine hose connection to gun and make sure it is
secure. Test trigger by pressing it and making sure it
springs back into place when you release it. Engage
safety latch and test trigger. You should not be able to
press trigger. Replace gun immediately if it fails any of
these tests.
Check In-Line Filter
Refer to the illustration and service the in-line filter if it
becomes clogged, as follows:
1. Detach nozzle extension from gun and remove
o-ring and screen from nozzle extension. Flush
screen, gun, and nozzle extension with clean water
to clear debris.
2. Place in-line filter screen into threaded end of
nozzle extension. Direction does not matter. Push
screen in with eraser end of pencil until it rests flat
at bottom of opening. Take care not to bend
screen.
3. Place o-ring into recess. Push o-ring snugly against
in-line filter screen.
4. Assemble nozzle extension to spray gun, as
described earlier in manual.
Nozzle Maintenance
A pulsing sensation felt while squeezing the spray gun
trigger may be caused by excessive pump pressure.
The principal cause of excessive pump pressure is a
nozzle clogged or restricted with foreign materials,
such as dirt, etc. To correct the problem, immediately
clean the nozzle following these instructions:
1. Shut off engine and turn off water supply.
2. Remove nozzle from end of nozzle extension.
Separate nozzle extension from spray gun. Twist
nozzle clockwise to stream position. Using a 2mm
(5/64) allen wrench, remove orifice from end of
nozzle extension.
3. Remove in-line filter from other end of nozzle
extension.
4. Use a small paper clip to free any foreign material
clogging or restricting orifice.
5. Using a garden hose, remove additional debris by
back flushing water through nozzle extension. Back
flush between 30 to 60 seconds. Turn adjustable
nozzle extension to stream spray and move nozzle
from low to high while flushing.
6. Reinstall orifice and in-line filter into nozzle
extension. DO NOT overtighten orifice with allen
wrench.
7. Reconnect nozzle extension to spray gun.
8. Reconnect water supply, turn on water, and start
engine.
9. Test pressure washer by operating nozzle in high
and low positions.
Nozzle extension
In-line Filter
O-ring
Insert wire into orifice and turn back
and forth to clear obstruction.
NEVER repair high pressure hose. Replace it.
Replacement hose rating MUST exceed maximum
pressure rating of unit.
The high pressure stream of water that this
equipment produces can pierce skin and its
underlying tissues, leading to serious injury
and possible amputation.
WARNING
DO NOT insert any objects through cooling slots.
Improper treatment of pressure washer can
damage it and shorten its life.
CAUTION
16
O–Ring Maintenance
Purchase an O–Ring Repair Kit, item number
191922GS, at your local Sears sevice center. It is not
included with the pressure washer. This kit includes
replacement o-rings, rubber washer and water inlet filter.
Refer to the instruction sheet provided in the kit to
service your unit’s o-rings.
Pump Oil Maintenance
This model does not require any pump maintenance.
The pump is pre-lubricated and sealed, requiring no
additional lubrication for the life of the pump.
ENGINE MAINTENANCE
Oil
Oil Recommendations
NOTE: When adding oil to the engine crankcase, use
only high quality detergent oil rated with API service
classification SF, SG, SH, SJ or higher. DO NOT use
special additives.
1. Choose a viscosity according to the following table:
NOTE: Synthetic oil meeting ILSAC GF-2, API
certification mark and API service symbol with “SJ/CF
ENERGY CONSERVING” or higher, is an acceptable
oil at all temperatures. Use of synthetic oil does not
alter required oil change intervals.
* The use of multi-viscosity oils (5W-30, 10W-30, etc.)
in temperatures above 40°F (4°C) will result in higher
than normal oil consumption. When using a multi-
viscosity oil, check oil more frequently.
** If using SAE 30 oil in temperatures below 40°F
(4°C), it will result in hard starting and possible engine
bore damage due to inadequate lubrication.
Checking Oil Level
Oil level should be checked prior to each use or at least
every 5 hours of operation. Keep oil level maintained.
1. Make sure pressure washer is on a level surface.
2. Remove oil dipstick and wipe dipstick with clean
cloth. Replace and tighten dipstick. Remove and
and check oil level.
3. Verify oil is at “Full” mark on dipstick. Replace and
tighten dipstick.
NEVER repair leaking connections with sealant of any
kind. Replace o-ring or seal.
The high pressure stream of water that this
equipment produces can pierce skin and its
underlying tissues, leading to serious injury
and possible amputation.
WARNING
WHEN ADJUSTING OR MAKING REPAIRS TO YOUR
PRESSURE WASHER
Disconnect the spark plug wire from the spark plug and
place the wire where it cannot contact spark plug.
WHEN TESTING FOR ENGINE SPARK
Use approved spark plug tester.
DO NOT check for spark with spark plug removed.
Unintentional sparking can result in fire or
electric shock.
WARNING
Synthetic 5W-30, 10W-30
5W-30, 10W-30
30
°F -20 0 20 32 40 60 80 100
°C -30 -20 -10 0 10 20 30 40
STARTING TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
17
Adding Engine Oil
1. Make sure pressure washer is on a level surface.
2. Check oil level as described in “Checking Oil Level”.
3. If needed, slowly pour oil into oil fill opening to the
Full” mark on dipstick. DO NOT overfill.
4. Replace and tighten dipstick.
Changing Engine Oil
Change engine oil after the first 5 hours and every
50 hours thereafter. If you are using your pressure
washer under extremely dirty or dusty conditions, or in
extremely hot weather, change oil more often.
KEEP OUT OF REACH OF CHILDREN.
DON'T POLLUTE. CONSERVE
RESOURCES. RETURN USED OIL TO
COLLECTION CENTERS.
Change oil while engine is still warm from running, as
follows:
1. Drain fuel tank by running pressure washer until
fuel tank is empty.
2. Disconnect spark plug wire and keep it away from
spark plug.
3. Clean area around oil fill, remove oil fill
cap/dipstick. Wipe dipstick clean.
4. Tip your pressure washer to drain oil from oil fill
into a suitable container making sure you tip your
unit away from spark plug. When crankcase is
empty, return pressure washer to upright position.
5. Slowly pour recommended oil (about 20 oz.) into
oil fill opening. Pause to permit oil to settle. Fill to
Full” mark on dipstick.
6. Wipe dipstick clean each time oil level is checked.
DO NOT overfill.
7. Replace and tighten dipstick.
8. Wipe up any remaining oil.
9. Reconnect spark plug wire to spark plug.
Service Air Cleaner
Your engine will not run properly and may be
damaged if you run it with a dirty air cleaner.
Service the air cleaner once every 25 hours of
operation or once each year, whichever comes first.
Service more often if operating under dirty or dusty
conditions. Replacements are available at your local
Sears service center.
To service the air cleaner, follow these steps:
1. Remove screw.
2. Carefully remove air cleaner assembly to prevent
debris from falling into carburetor.
3. Take air cleaner assembly apart and clean all
parts. Wash foam air cleaner in liquid detergent
and water. Squeeze dry in a clean cloth.
4. SATURATE foam air cleaner in engine oil and
squeeze in a clean cloth to remove excess oil.
5. Reinstall clean or new foam air cleaner in body.
6. Install air cleaner securely on carburetor with
screw.
Service Spark Plug
Service the spark plug every 100 hours of operation or
yearly, whichever occurs first.
1. Clean area around spark plug.
2. Remove and inspect spark plug.
3. Replace spark plug with recommended plug if
electrodes are worn or if insulator is cracked or
chipped.
4. Check electrode gap with wire feeler gauge and
set gap at 0.030 inches (0.76mm), if necessary.
5. Install spark plug, tighten securely.
Used motor oil has been shown to cause skin cancer in
certain laboratory animals.
Thoroughly wash exposed areas with soap and water.
Avoid prolonged or repeated skin contact with used
motor oil.
CAUTION
18
Spark Arrester Service
Your engine is not factory-equipped with a spark
arrester. In some areas, it is illegal to operate an
engine without a spark arrester. Check local laws and
regulations. A spark arrester is available from your
nearest Sears service center. If you need to order a
spark arrester, contact your local Sears service center.
The spark arrester must be serviced every 50 hours to
keep it functioning as designed.
If the engine has been running, the muffler will be very
hot. Allow the muffler to cool before servicing spark
arrester.
Remove spark arrester screen for cleaning and
inspection.
Replace if screen is damaged.
Air Cooling System
Over time debris may accumulate in cylinder cooling
fins and cannot be observed without partial engine
disassembly. For this reason, we recommend you have
an authorized Sears service dealer clean the cooling
system per recommended intervals (see “Maintenance
Schedule” on page 14). Equally important is to keep top
of engine free from debris. See “Clean Debris”.
Clean Combustion Chamber
We recommend you have an authorized Sears service
dealer remove combustion deposits from the cylinder,
cylinder head, top of piston and around valves per
recommended intervals (see “Maintenance Schedule”
on page 14).
Keep areas within heavy line clear of debris.
DO NOT touch hot surfaces and avoid hot exhaust gases.
Allow equipment to cool before touching.
Keep at least 5 ft. (152 cm) clearance on all sides of
pressure washer including overhead.
Code of Federal Regulation (CFR) Title 36 Parks,
Forests, and Public Property require equipment powered
by an internal combustion engine to have a spark
arrester, maintained in effective working order, complying
to USDA Forest service standard 5100-1C or later
revision. In the State of California a spark arrester is
required under section 4442 of the California Public
resources code. Other states may have similar laws.
Running engines produce heat.
Temperature of muffler and nearby areas
can reach or exceed 150°F (65°C).
Severe burns can occur on contact.
Exhaust heat/gases can ignite combustibles,
structures or damage fuel tank causing a fire.
WARNING
19
AFTER EACH USE
Water should not remain in the unit for long periods of
time. Sediments or minerals can deposit on pump
parts and “freeze” pump action. Follow these
procedures after every use:
1. Flush detergent siphoning tube by placing the filter
into a pail of clean water while running pressure
washer in low pressure mode. Flush for one to two
minutes.
2. Shut off engine, let it cool, then remove all hoses.
3. Empty pump of all liquids by pulling recoil handle
about 6 times. This should remove most liquid in
pump.
4. If storing for more than 30 days see “Long Term
Storage” on next page.
5. Coil high pressure hose and inspect it for damage.
Cuts in hose or fraying could result in leaks and
loss of pressure. Should any damage be found,
replace hose. DO NOT attempt to repair a
damaged hose. Replace hose with genuine Sears
part.
6. Disconnect hose from spray gun and high
pressure outlet on pump. Drain water from hose,
gun, and nozzle extension. Use a rag to wipe off
hose.
7. Store unit in a clean, dry area.
WINTER STORAGE
To protect the unit from freezing temperatures:
1. Flush detergent siphoning tube by placing filter
into a pail of clean water while running pressure
washer in low pressure mode. Flush for one to two
minutes.
2. Empty pump of all pumped liquids by pulling recoil
handle about 6 times. This should remove most
liquid in pump.
3. Use pump saver, available at a local Sears service
center, to treat pump. This minimizes freeze
damage and lubricates pistons and seals.
4. If pump saver is not available, connect a 3-foot
section of garden hose to water inlet adapter. Pour
RV–antifreeze (antifreeze without alcohol) into
hose. Pull recoil handle twice. Disconnect 3-foot
hose.
STORAGE
CAUTION
Failure to do so will permanently damage your pump
and render your unit inoperable.
Freeze damage is not covered under warranty.
You must protect your unit from freezing temperatures.
WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN
TANK
Store away from furnaces, stoves, water heaters, clothes
dryers or other appliances that have pilot light or other
ignition source because they can ignite fuel vapors.
WHEN DRAINING FUEL
Turn pressure washer OFF and let it cool at least 2
minutes before removing fuel cap. Loosen cap slowly to
relieve pressure in tank.
Drain fuel tank outdoors.
Keep fuel away from sparks, open flames, pilot lights,
heat, and other ignition sources.
DO NOT light a cigarette or smoke.
Fuel and its vapors are extremely flammable
and explosive.
Fire or explosion can cause severe burns or
death.
WARNING
20
LONG TERM STORAGE
If you do not plan to use the pressure washer for more
than 30 days, you must prepare the engine and pump
for long term storage.
It is important to prevent gum deposits from forming in
essential fuel system parts such as the carburetor, fuel
filter, fuel hose or tank during storage. Also,
experience indicates that alcohol-blended fuels (called
gasohol, ethanol or methanol) can attract moisture,
which leads to separation and formation of acids
during storage. Acidic gas can damage the fuel
system of an engine while in storage.
Protect Fuel System
Fuel Additive:
If adding a fuel additive, fill the fuel tank with fresh
fuel. If only partially filled, air in the tank will promote
fuel deterioration during storage. Engine and fuel can
be stored up to 24 months with additive.
Add fuel additive following manufacturer’s
instructions.
Make sure you have water supply to pump inlet
connected and turned ON.
Run the engine outdoors for 10 minutes to be sure
that treated fuel has replaced the untreated fuel in
the carburetor.
If fuel additive is not used, remove all fuel from tank
and run engine until it stops from lack of fuel.
Change Oil
While engine is still warm, drain oil from crankcase.
Refill with recommended grade. See “Changing Oil”
on page 17.
Oil Cylinder Bore
Remove spark plug. Squirt about 1/2 oz. of clean
engine oil into the cylinder. Cover spark plug hole
with rag. Pull recoil handle slowly to distribute oil.
Avoid spray from spark plug hole.
Install spark plug. DO NOT connect spark plug
wire.
Protect Pump
To protect the pump use Sears pump saver to prevent
freeze damage and lubricate pistons and seals.
NOTE: Sears pump saver is available as an optional
accessory. It is not included with the pressure washer.
To use the pump saver:
1. Attach hose on pump saver can to pump inlet.
2. Push in can top to dispense pump saver.
3. When pump saver fluid begins to exit pump outlet,
the pump is protected.
4. Remove pump saver from pump inlet.
OTHER
DO NOT store fuel from one season to another.
If possible, store your unit indoors and cover it to
give protection from dust and dirt. BE SURE TO
EMPTY THE FUEL TANK.
CAUTION
Failure to do so will permanently damage your pump
and render your unit inoperable.
Freeze damage is not covered under warranty.
You must protect your unit from freezing temperatures.
Always wear eye protection when using PumpSaver.
Read and follow all cautions and warnings on the
PumpSaver can label.
CAUTION
DO NOT place a storage cover over a hot pressure
washer.
Let equipment cool for a sufficient time before placing
the cover on the equipment.
Storage covers can be flammable.
WARNING
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Simplicity 020248-1 Manuel utilisateur

Catégorie
Nettoyeurs haute pression
Taper
Manuel utilisateur

dans d''autres langues