Skil RS582901 Le manuel du propriétaire

Marque: Skil

Modèle: RS582901

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

Ce manuel convient également à

RS582902

WARNING: To reduce the risk of injury, the user must read and understand the

Owner’s Manual before using this product. Save these instructions for future reference.

AVERTISSEMENT : Afin de réduire les risques de blessure, l’utilisateur doit lire et

comprendre le guide d’utilisation avant d’utiliser cet article. Conservez le présent guide

afin de pouvoir le consulter ultérieurement.

ADVERTENCIA : Para reducir el riesgo de lesiones, el usuario debe leer y comprender

el Manual del operador antes de utilizar este producto. Guarde estas instrucciones para

consultarlas en caso sea necesario.

Owner’s Manual

Guide d’utilisation

Manual del propietario

For Customer Service

Pour le service à la clientèle

Servicio al cliente

1-877-SKIL-999

www.skil.com

20V Compact Reciprocating Saw

Scie alternative compacte de 20V

Model/ Modelo/ Modèle: RS582901

TABLE OF CONTENTS

General Power Tool Safety Warnings . ............................3-5

Safety Warnings for Reciprocating Saw .............................5

Symbols .....................................................6-9

Get to Know Your Reciprocating Saw ..............................10

Specications .................................................10

Operating Instructions .......................................11-18

Maintenance ...................................................19

Troubleshooting ...............................................19

Limited Warranty of SKIL Cordless Tool ............................20

WARNING

•

Some dust created by power sanding, sawing, grinding, drilling and other construction

activities contains chemicals known to the State of California to cause cancer, birth defects

or other reproductive harm. Some examples of these chemicals are:

–

Lead from lead-based paints.

–

Crystalline silica from bricks, cement, and other masonry products.

–

Arsenic and chromium from chemically-treated lumber.

•

Your risk from these exposures varies, depending upon how often you do this type of work.

To reduce your exposure to these chemicals:

–

Work in a well-ventilated area.

–

Work with approved safety equipment, such as dust masks that are specially designed to

lter out microscopic particles.

–

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with soap

and water. Allowing dust to get into your mouth or eyes or to lie on the skin may promote

absorption of harmful chemicals.

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings, instructions, illustrations and specications

provided with this power tool. Failure to follow all instructions listed

below may result in electric shock, re and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE

REFERENCE.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

Work area safety

Keep work area clean and well lit. Cluttered or dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or

fumes.

Keep children and bystanders away while operating a power tool. Distractions can cause

you to lose control.

Electrical safety

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use

any adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching

outlets will reduce risk of electric shock.

Avoid body contact with earthed or grounded surfaces, such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your body is earthed

or grounded.

Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

When operating a power tool outdoors, use an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

If operating a power tool in a damp location is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.

Personal safety

Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use a power tool while you are tired or under the influence of drugs,

alcohol or medication. A moment of inattention while operating power tools may result in

serious personal injury.

Use personal protective equipment. Always wear eye protection. Protective equipment

such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for

appropriate conditions will reduce personal injuries.

Prevent unintentional starting. Ensure the switch is in the off-position before

connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your nger on the switch or energising power tools that have the

switch on invites accidents.

Remove any adjusting key or wrench before turning the power tool on. A wrench or a

key left attached to a rotating part of the power tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times. This enables better

control of the power tool in unexpected situations.

Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing

away from moving parts. Loose clothes, jewellery or long hair can be caught in moving

parts.

If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used. Use of dust collection can reduce dust-

related hazards.

Do not let familiarity gained from frequent use of tools allow you to become complacent

and ignore tool safety principles. A careless action can cause severe injury within a fraction

of a second.

Power tool use and care

Do not force the power tool. Use the correct power tool for your application. The correct

power tool will do the job better and safer at the rate for which it was designed.

Do not use the power tool if the switch does not turn it on and off. Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

Disconnect the plug from the power source and/or remove the battery pack, if

detachable, from the power tool before making any adjustments, changing accessories,

or storing power tools. Such preventive safety measures reduce the risk of starting the

power tool accidentally.

Store idle power tools out of the reach of children and do not allow persons unfamiliar

with the power tool or these instructions to operate the power tool. Power tools are

dangerous in the hands of untrained users.

Maintain power tools and accessories. Check for misalignment or binding of moving

parts, breakage of parts and any other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired before use. Many accidents are

caused by poorly maintained power tools.

Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

Use the power tool, accessories and tool bits etc. in accordance with these instructions,

taking into account the working conditions and the work to be performed. Use of the

power tool for operations different from those intended could result in a hazardous situation.

Keep handles and grasping surfaces dry, clean and free from oil and grease.

Slippery handles and grasping surfaces do not allow for safe handling and control of the tool

in unexpected situations.

Battery tool use and care

Recharge only with the charger specied by the manufacturer. A charger that is suitable

for one type of battery pack may create a risk of re when used with another battery pack.

Use power tools only with specically designated battery packs. Use of any other battery

packs may create a risk of injury and re.

When battery pack is not in use, keep it away from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal objects, that can make a connection

from one terminal to another. Shorting the battery terminals together may cause burns or a

re.

Under abusive conditions, liquid may be ejected from the battery; avoid contact. If

contact accidentally occurs, ush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause irritation or burns.

Do not use a battery pack or tool that is damaged or modied. Damaged or modied

batteries may exhibit unpredictable behaviour resulting in re, explosion or risk of injury.

Do not expose a battery pack or tool to re or excessive temperature. Exposure to re or

temperature above 265 °F may cause explosion.

Follow all charging instructions and do not charge the battery pack or tool outside the

temperature range specied in the instructions. Charging improperly or at temperatures

outside the specied range may damage the battery and increase the risk of re.

Service

Have your power tool serviced by a qualied repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

Never service damaged battery packs. Service of battery packs should only be performed

by the manufacturer or authorized service providers.

SAFETY WARNINGS FOR RECIPROCATING SAW

Hold the power tool by insulated gripping surfaces, when performing an operation

where the cutting accessory may contact hidden wiring. Cutting accessory contacting a

"live" wire may make exposed metal parts of the power tool "live" and could give the operator

an electric shock.

Use clamps or another practical way to secure and support the workpiece to a stable

platform. Holding the workpiece by hand or against your body leaves it unstable and may

lead to loss of control.

SYMBOLS

Safety Symbols

The purpose of safety symbols is to attract your attention to possible dangers. The safety

symbols and the explanations with them deserve your careful attention and understanding.

The symbol warnings do not, by themselves, eliminate any danger. The instructions and

warnings they give are no substitutes for proper accident prevention measures.

WARNING

Be sure to read and understand all safety instructions in this Owner's

Manual, including all safety alert symbols such as “DANGER,”

“WARNING,” and “CAUTION” before using this tool. Failure to following all instructions listed

below may result in electric shock, re, and/or serious personal injury.

The denitions below describe the level of severity for each signal word. Please read the manual

and pay attention to these symbols.

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION

CAUTION, used with the safety alert symbol, indicates a hazardous

situation which, if not avoided, will result in minor or moderate injury.

Damage Prevention and Information Messages

These inform the user of important information and/or instructions that could lead to equipment

or other property damage if they are not followed. Each message is preceded by the word

“NOTICE”, as in the example below:

NOTICE: Equipment and/or property damage may result if these instructions are not followed.

WARNING

The operation of any power tools can result in

foreign

objects being thrown into your eyes, which can result

in severe eye damage. Before beginning power tool operation, always

wear safety goggles or safety glasses with side shields and a full face

shield when needed. We recommend a Wide Vision Safety Mask for use

over eyeglasses or standard safety glasses with side shields. Always use

eye protection which is marked to comply with ANSI Z87.1.

SYMBOLS (CONTINUED)

IMPORTANT: Some of the following symbols may be used on your tool. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate the

tool better and more safely.

Symbol Name Designation/Explanation

V Volts Voltage (potential)

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

kg Kilograms Weight

min Minutes Time

s Seconds Time

Wh Watt-hours Battery capacity

Ah Ampere-Hours Battery capacity

Ø Diameter Size of drill bits, grinding wheels, etc.

No load speed Rotational speed, at no load

n Rated speed Maximum attainable speed

…/min

Revolutions or reciprocation

per minute

Revolutions, strokes, surface speed,

orbits, etc. per minute

0 Off position Zero speed, zero torque...

1,2,3,…

I,II,III,

Selector settings

Speed, torque or position settings. Higher

number means greater speed

Innitely variable selector

with off

Speed is increasing from 0 setting

Arrow Action in the direction of arrow

Alternating current Type or a characteristic of current

Direct current Type or a characteristic of current

Alternating or direct current Type or a characteristic of current

Class II construction

Designates Double Insulated Construction

tools.

Earthing terminal Grounding terminal

Li-ion RBRC seal

Designates Li-ion battery recycling

program

Symbol Name Designation/Explanation

Ni-Cad RBRC seal

Designates Ni-Cad battery recycling

program

Read manual symbol Alerts user to read manual

Wear eye protection symbol

Always wear safety goggles or safety

glasses with side shields and a full face

shield when operating this product.

SYMBOLS (CERTIFICATION INFORMATION)

IMPORTANT: Some of the following symbols for certication information may be used on your

tool. Please study them and learn their meaning. Proper interpretation of these symbols will

allow you to operate the tool better and more safely.

Symbol Designation/Explanation

This symbol designates that this tool is listed by Underwriters Laboratories.

This symbol designates that this tool is recognized by Underwriters

Laboratories.

This symbol designates that this tool is listed by Underwriters

Laboratories, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Canadian

Standards Association.

This symbol designates that this tool is listed by the Canadian

Standards Association, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Intertek Testing

Services, to United States and Canadian Standards.

This symbol designates that this tool complies to NOM Mexican

Standards.

GET TO KNOW YOUR RECIPROCATING SAW

20V Reciprocating Saw

Tool-less Blade

Clamp Sleeve

Pivot Shoe

LED Light

Lock-off Button

Variable-Speed

Trigger Switch

Hex Key

Shoe-Release

Screws

Fig. 1

SPECIFICATIONS

Rated voltage 20V d.c.

No-load speed 0~3000 SPM (Strokes per Minute)

Stroke 1’’ (25mm)

Sawing capacity in wood 4-3/4’’ (120 mm)

Sawing capacity in aluminum 15/16’’ (24 mm)

Sawing capacity in metal 3/4’’ (20 mm)

Recommended working temperature 14 ~ 104°F (-10 ~ 40°C)

Recommended storage temperature 32 ~ 104°F (0 ~ 40°C)

OPERATING INSTRUCTIONS

WARNING

To reduce the risk of re, personal injury, and product damage due to

a short circuit, never immerse your tool, battery pack, or charger in

fluid or allow a fluid to flow inside them. Corrosive or conductive uids, such as seawater,

certain industrial chemicals, and bleach or bleach-containing products, etc, can cause a short

circuit.

WARNING

If any parts are damaged or missing, do not operate this product until

the parts are replaced. Use of this product with damaged or missing parts

could result in serious personal injury.

WARNING

Do not attempt to modify this tool or create accessories not recom-

mended for use with this tool. Any such alteration or modication is

misuse and could result in a hazardous condition leading to possible serious injury.

WARNING

To prevent accidental starting that could cause serious personal

injury, always remove the battery pack from the tool when assem-

bling parts.

This cordless reciprocating saw must be used only with the battery packs and charger

listed below:

Battery Pack

Charger

2Ah 4Ah 5Ah

SKIL BY519701 SKIL BY519601 SKIL BY519603 SKIL SC535801

NOTICE: Please refer to the battery and charger manual for detailed operating information.

Lock-off Button (Fig. 2)

Your tool is equipped with a lock-off button, located above the variable-speed trigger switch, to

prevent the saw from being activated unintentionally.

To lock the switch in the off position, depress the lock-off button to the

(locked) position.

To unlock the switch, depress the lock-off button to the

(unlocked) position.

Fig. 2

To Attach/Detach Battery Pack

Lock the variable-speed trigger switch “OFF”

on the tool by depressing the lock-off button to

the locked position

To attach the battery pack:

Align the raised rib on the battery pack with the

grooves on the tool, and then slide the battery

pack onto the tool (Fig. 3).

To detach the battery pack:

Depress the battery-release button, located

on the front of the battery pack, to release the

battery pack. Pull the battery pack out and

remove it from the tool (Fig. 3).

NOTICE: When placing the battery pack on

the tool, be sure that the raised rib on the battery pack aligns with the groove in the tool and

that the latches snap into place properly. Improper attachment of the battery pack can cause

damage to internal components.

WARNING

Battery tools are always in operating condition. Therefore, the lock-

off button should always be depressed and in the locked position

when the tool is not in use or carrying at your side.

Variable-Speed Trigger Switch

Your tool is equipped with a variable-speed

trigger switch. The tool can be turned "ON" or

"OFF" by depressing or releasing the

variable-speed trigger switch.

The variable-speed trigger switch delivers

higher speed with increased trigger pressure

and lower speed with decreased trigger

pressure (Fig. 4).

LED Light

Your tool is equipped with an LED, located

above the blade clamp on the tool. This LED

provides additional light on the surface of the

work piece for operation in lower-light areas.

The LED will automatically turn on with a slight

squeeze on the variable-speed trigger switch

before the tool starts running, and will turn off 8

to 12 seconds after the variable-speed trigger

switch is released.

The LED will rapidly ash when the tool and/or

battery pack becomes overloaded or too hot,

and the internal sensors will turn the tool off

Fig. 3

Battery-Release Button

Detach

Attach

Fig. 4

Variable-speed

Trigger Switch

Fig. 5

LED Light

if the tool and/or battery pack are overloaded. Rest the tool for a while or place the tool and

battery pack separately under air ow for to cool them.

The LED light will ash more slowly to indicate that the battery is at low-battery capacity.

Recharge the battery pack.

Blade Selection

To obtain the best performance from the saw, it is important to select the correct blade for the

particular application and type of material to be cut.

Blades with fewer teeth, e.g., 7 teeth per inch (TPI), are typically used for cutting wood; blades

with more teeth per inch are better for cutting metal or plastic.

We recommend 14 TPI blades for plastics and soft metals and 18 TPI blades for hard metals.

Installing and Removing the Saw Blade (Fig. 6)

WARNING

Always lock the tool off and remove the battery pack before making

any adjustments or assembling parts.

Depress the lock-off button to the locked position and then remove the battery pack from the

tool.

To install the saw blade:

a. Use one hand to rotate the tool-less blade clamp sleeve in the direction of the arrow marked

on the blade clamp and then hold it in place.

b. Use the other hand to insert the saw blade into the blade clamp as far as possible.

c. Release the tool-less blade clamp sleeve, and the blade should be locked in place

automatically.

d. Try to push in and pull out blade to check whether it is locked correctly.

NOTICE: The blade may be installed with the teeth pointing up or down, according to the

needs of the cutting operation.

To remove the saw blade:

a. Use one hand to rotate the tool-less blade clamp sleeve in the direction of the arrow marked

on the blade clamp and hold it.

b. Remove the saw blade from the blade clamp.

c. Release the tool-less blade clamp sleeve.

Fig. 6

Tool-less Blade

Change Cover

WARNING

Use protective gloves when removing the saw blade from the tool, or

rst allow the saw blade to cool down. The saw blade may be hot

after prolonged use.

Pivot Shoe Adjustment (Fig. 7)

Your tool is equipped with a pivot shoe that can

slide in and out to adjust the effective stroke

length for maximum control and longer blade

life.

a. Depress the lock-off button to the locked

position and then remove the battery pack

from the tool.

b. Loosen the shoe-release screws by turning

them counterclockwise with the hex key

(supplied) and slide the shoe to the desired

position.

c. Tighten the shoe-release screws by turning

them clockwise with the hex key (supplied)

to lock the shoe in the desired position.

WARNING

To avoid injury and damage, do not operate the saw without the pivot

shoe in place. The blade clamp may strike against the workpiece and

damage the reciprocating mechanism.

WARNING

Make sure that the front end of the blade extends through the shoe

for the entire stroke length (Fig. 8).Do not use specialty blades that are

very short or those with signicant tilt. The blade must not contact the shoe. A blade that is too

short or is tilted could jam inside the shoe and then snap.

Fig. 8

17 mm

Fig. 7

Pivoting the Shoe (Fig. 9)

The shoe pivots to provide maximum control

when it is aligned against the surface being

cut.

a. Depress the lock-off button to the locked

position and then remove the battery pack

from the tool.

b. Firmly hold the saw and then pivot the shoe

to the desired angle, while taking care to

avoid contact with the blade.

c. Reinstall the battery and prepare to cut.

General Cutting (Fig. 10)

WARNING

Never use the wood-

cutting blade for cutting

metals. Failure to do so could result in serious

personal injury.

WARNING

Before attaching the

battery pack onto the

tool, always check to determine that the

switch performs properly and returns to the

“OFF” position when released.

WARNING

Hold the tool only by the

plastic handle and the

insulated grip area to help prevent electrical

shock. When sawing into walls or oors

you may encounter electrical wiring.

Sawing into a “live” wire will conduct

electricity into the tool.

a. Depress the lock-off button to the locked position and then remove the battery pack from

the tool.

b. Make sure that the workpiece is rmly clamped in place to keep it from slipping or moving

while cutting.

c. Intall the appropriate type and size of blade for the workpiece material and size.

d. Adjust the pivot shoe as necessary to make sure that the blade will extend beyond the shoe

and through the workpiece at all times.

e. Adjust the pivot shoe as necessary to expose unworn blade teeth for longer blade life.

f. Check for clearance behind the workpiece so that the blade will not contact another surface.

g. Mark the line of cut clearly. If cutting metal, apply cutting oil to the line.

h. Attach the battery pack to the reciprocating saw.

i. Hold the saw rmly with both hands. Make sure to keep your hands on the insulated

gripping areas only.

j. Depress the lock-off button to the unlock position and squeeze the variable-speed trigger

switch to start the saw and bring it to the maximum desired cutting speed before applying

the blade to the workpiece.

Fig. 10

Fig. 9

Pivot Shoe

k. Place the shoe rmly on the workpiece while cutting. Use only enough steady pressure on

the blade to keep the saw cutting. Do not force the tool.

l. Reduce pressure as the blade comes to the end of the cut.

m. Allow the saw to come to a complete stop before removing the blade from the workpiece.

NOTICE: When sawing berglass, plaster, wallboard, or spackling compound, clean the motor

vents frequently with a vacuum or with compressed air. These materials are highly abrasive

and may accelerate the wear on motor bearings and brushes.

WARNING

Always wear safety goggles when cleaning tools with compressed

air.

NOTICE: Cutting speeds should vary with the workpiece. Hard materials, such as metals,

require lower speeds; use higher speeds for softer materials.

WARNING

Always wear safety goggles or safety glasses with side shields

during power tool operation or when blowing dust. If operation is

dusty, also wear a dust mask.

WARNING

Do not allow familiarity with the saw to make you careless. One

careless fraction of a second is enough to inict serious injury.

Plunge Cutting (Fig. 11)

Your reciprocating saw is ideal for plunge cutting directly into surfaces that cannot be cut from

an edge, such as in walls or oors. Plunge cutting may be done two ways, depending on how

the blade is inserted.

Figure 11, A shows how to plunge cut with the teeth of the blade facing down.

Figure 11, B shows how to plunge cut with the teeth of the blade facing up.

A B

Fig. 11

WARNING

Do not plunge cut into metal surfaces.

a. Depress the lock-off button to the locked position and then remove the battery pack from

the tool.

b. Make sure that the workpiece is rmly clamped in place to keep it from slipping or moving

while cutting.

c. Select the appropriate type and size of blade for the workpiece material and size. Install the

blade onto the tool.

d. Adjust the pivot shoe as necessary to make sure that the blade will extend beyond the shoe

and through the workpiece at all times.

e. Adjust the pivot shoe as necessary to expose unworn blade teeth for longer blade life.

f. Check for clearance behind the workpiece so that the blade will not contact another surface.

g. Mark the line of cut clearly.

h. Attach the battery pack to the reciprocating saw.

i. If the blade is inserted with the teeth facing downward, hold the tool as shown in Column A,

resting the edge of the shoe on the workpiece.

NOTICE: To make plunge cutting easier, use a heavy gauge blade and install the blade with

the teeth facing upward relative to the normal upright operating position of the saw, as show in

Column B.

j. With the blade just above the workpiece, depress the lock-off button to the unlock position

and squeeze the variable-speed trigger switch to start the tool; allow it to come to the

desired speed. Then, using the edge of the shoe as a pivot, lower the blade into the

workpiece.

k. As the blade starts cutting, raise the handle of the tool slowly, until the shoe rests rmly on

the workpiece.

l. After the blade has penetrated through the workpiece, continue sawing along the marked

cutting line.

m. Allow the saw to come to a complete stop before removing the blade from the workpiece.

WARNING

To reduce the risk of explosion, electric shock and property damage,

always check the work area for hidden gas pipes, electrical wires or

water pipes when making blind or plunge cuts.

WARNING

To avoid loss of control and serious injury, make sure that the blade

reaches the full desired speed before touching it to the workpiece.

WARNING

Do not make plunge cuts in metal materials.

Metal Cutting

WARNING

Never use the wood-cutting blade for cutting metals. Failure to do so

could result in serious personal injury.

The saw can be used to cut metals, such as sheet steel, pipe, steel rods, aluminum, brass,

and copper. Be careful not to twist or bend the saw blade. Do not force the tool.

The use of cutting oil is recommended when cutting soft metals and steel. Cutting oil will keep

the blade cool, increase the cutting action, and prolong blade life.

WARNING

To avoid possible serious injury:

•

Never use gasoline as cutting lubricant, because normal sparking could ignite the

fumes.

•

Securely clamp the workpiece in position, and make the cut close to the clamping

point to minimize vibration.

•

When cutting conduit pipe or angle iron, clamp the work in a vise, if possible, and cut

close to the vise.

•

To cut thin sheet material, “sandwich” the material between pieces of hardboard

or plywood, and clamp the layers together to reduce vibration and tearing of the

material.

MAINTENANCE

WARNING

To avoid serious personal injury, always remove the battery pack

from the tool when cleaning or performing any maintenance.

Service

WARNING

Preventive maintenance performed by unauthorized personnel may

result in misplacing of internal wires and components which could

cause serious hazard. We recommend that all tool service be performed by a SKIL Factory

Service Center or Authorized SKIL Service Station.

General Maintenance

WARNING

When servicing, use only identical replacement parts. Use of any

other parts could create a hazard or cause product damage.

Periodically inspect the entire product for damaged, missing, or loose parts such as screws,

nuts, bolts, caps, etc. Securely tighten all fasteners and caps and do not operate this product

until all missing or damaged parts are replaced. Please contact customer service or an

authorized service center for assistance.

Cleaning

WARNING

The tool may be cleaned most effectively with compressed dry air. Always

wear safety goggles when cleaning tools with compressed air.

Ventilation openings and switch selectors must be kept clean and free of foreign matter. Do

not attempt to clean by inserting pointed objects through openings.

WARNING

Certain cleaning agents and solvents damage plastic parts. Some of

these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents,

ammonia and household detergents that contain ammonia.

Storage

Store the tool indoors in a place that is inaccessible to children. Keep away from corrosive

agents.

TROUBLESHOOTING

Problem Cause Remedy

Tool will not start. 1. Battery pack is depleted.

2. Battery pack is not installed

properly.

3. Burned out switch.

1. Charge the battery.

2. Conrm battery is locked and

secured to the tool.

3. Have the switch replaced by an

Authorized SKIL Service Center or

Service Station.

The blade binds,

jams, or bums the

wood.

1. The blade is dull.

2. An improper blade is being

used.

3. The blade is warped.

1. Replace the blade.

2. Choose the right blade for your

operation.

3. Replace the blade.

The saw vibrates or

shakes.

1. The blade is damaged.

2. The blade is loose.

1. Replace the blade.

2. Remove the blade and reinstall it.

LIMITED WARRANTY OF SKIL CONSUMER TOOLS

5 YEAR LIMITED WARRANTY- LEGAL

Chervon North America, Inc. ("Seller") warrants to the original purchaser only, that all SKIL

consumer TOOLS will be free from defects in material or workmanship for a period of ve

years from date of purchase, if original purchaser registers the product within 30 days from

purchase. BATTERIES AND CHARGERS are warranted for 2 years. Product registration

can be completed online at www.Registermyskil.com. Original purchasers should also retain

their receipt as proof of purchase. THE FIVE-YEAR WARRANTY PERIOD FOR TOOLS IS

CONDITIONED ON REGISTRATION OF THE PRODUCT WITHIN 30 DAYS OF PURCHASE.

If original purchasers do not register their product timely, the foregoing limited warranty will

apply for a duration of three years for tools. All batteries and chargers will remain under the

two-year limited warranty.

Notwithstanding the foregoing, if a SKIL consumer tool is used for industrial, professional

or commercial purposes, the foregoing warranty will apply for a duration of ninety days,

regardless of registration.

SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited

Warranty and, to the extent permitted by law, any warranty or condition implied by law, shall

be the repair or replacement of parts, without charge, which are defective in material or

workmanship and which have not been misused, carelessly handled, or repaired by persons

other than Seller or Authorized Service Station. To make a claim under this Limited Warranty,

you must return the complete product, transportation prepaid, to any SKIL Factory Service

Center or Authorized Service Station. For Authorized SKIL Power Tool Service Stations,

please visit www.Registermyskil.com or call 1-877-SKIL-999 (1-877-754-5999).

THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY ITEMS SUCH AS

CIRCULAR SAW BLADES, DRILL BITS, ROUTER BITS, JIGSAW BLADES, SANDING

BELTS, GRINDING WHEELS AND OTHER RELATED ITEMS.

ANY IMPLIED WARRANTIES APPLICABLE TO A PRODUCT SHALL BE LIMITED IN

DURATION EQUAL TO THE DURATION OF THE EXPRESS WARRANTIES APPLICABLE

TO SUCH PRODUCT, AS SET FORTH IN THE FIRST PARAGRAPH ABOVE. SOME

STATES IN THE U.S., SOME CANADIAN PROVINCES DO NOT ALLOW LIMITATIONS ON

HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT

APPLY TO YOU.

IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS)

ARISING FROM THE SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S.

AND SOME CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR

EXCLUSION MAY NOT APPLY TO YOU.

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO

HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE IN THE U.S., PROVINCE

TO PROVINCE IN CANADA AND FROM COUNTRY TO COUNTRY.

THIS LIMITED WARRANTY APPLIES ONLY TO PRODUCTS SOLD WITHIN THE UNITED

STATES OF AMERICA, CANADA AND THE COMMONWEALTH OF PUERTO RICO. FOR

WARRANTY COVERAGE WITHIN OTHER COUNTRIES, CONTACT YOUR LOCAL SKIL

DEALER OR IMPORTER.

08/18

La page charge ...

Skil RS582901 Le manuel du propriétaire

Marque: Skil

Modèle: RS582901

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

Ce manuel convient également à

RS582902

Télécharger le PDF

rapport

dans d''autres langues

English: Skil RS582901 Owner's manual

Skil RS582901 Le manuel du propriétaire

Ce manuel convient également à

Skil RS582901 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents