WIKA MG-1 Mode d'emploi

Operating instructions

Betriebsanleitung

Mode d'emploi

Manual de instrucciones

操作说明

GB

D

F

E

CN

Pressure transmitter model MG-1

Druckmessumformer Typ MG-1

Transmetteur de pression type MG-1

Transmisor de presión modelo MG-1

MG-1 型压力变送器

2 WIKA operating instructions pressure transmitter, model MG-1

GB

D

MM/YYYY country code based on 11609681.02 03/2013 GB/D/F/E

F

E

CN

WIKA

®

is a registered trademark in various countries.

WIKA

®

ist eine geschützte Marke in verschiedenen Ländern.

Prior to starting any work, read the operating instructions!

Keep for later use!

Vor Beginn aller Arbeiten Betriebsanleitung lesen!

Zum späteren Gebrauch aufbewahren!

Lire le mode d'emploi avant de commencer toute opération !

A conserver pour une utilisation ultérieure !

¡Leer el manual de instrucciones antes de comenzar cualquier trabajo!

¡Guardar el manual para una eventual consulta posterior!

开始工作之前，请仔细阅读本操作说明！保留以便后用！

Operating instructions model MG-1 Page 3 - 20

Betriebsanleitung Typ MG-1 Seite 25 - 46

Mode d'emploi type MG-1 Page 47 - 68

Manual de instrucciones modelo MG-1 Página 69 - 89

操作说明， MG-1 型页码

91 - 112

3WIKA operating instructions pressure transmitter, model MG-1

MM/YYYY country code based on 11609681.02 03/2013 GB/D/F/E

GB

1. General information 4

2. Safety 6

3. Specications 9

4. Design and function 11

5. Transport, packaging and storage 12

6. Commissioning, operation 13

7. Maintenance and cleaning 16

8. Faults 17

9. Dismounting, return and disposal 18

Appendix 1: EC Declaration of conformity for model MG-1 20

Appendix 2: BAM test report for model MG-1 21

Contents

Declarations of conformity can be found online at www.wika.com.

4 WIKA operating instructions pressure transmitter, model MG-1

MM/YYYY country code based on 11609681.02 03/2013 GB/D/F/E

GB

1. General information

■

The pressure transmitter described in the operating instructions has been designed and

manufactured by state-of-the-art technology. All components are subject to stringent quality

and environmental criteria during production. Our management systems are certied to

ISO 9001 and ISO 14001.

■

These operating instructions contain important information on handling the pressure

transmitter. Working safely requires that all safety instructions and work instructions are

observed.

■

Observe the relevant local accident prevention regulations and general safety regulations for

the pressure transmitter's range of use.

■

The operating instructions are part of the product and must be kept in the immediate vicinity of

the pressure transmitter and readily accessible to skilled personnel at any time.

■

Skilled personnel must have carefully read and understood the operating instructions prior to

beginning any work.

■

The manufacturer's liability is void in the case of any damage caused by using the product

contrary to its intended use, non-compliance with these operating instructions, assignment

of insuciently qualied skilled personnel or unauthorised modications to the pressure

transmitter.

■

The general terms and conditions contained in the sales documentation shall apply.

■

Subject to technical modications.

■

Further information:

- Internet address: www.wika.com

- Relevant data sheet: PE 81.44

- Application consultant: Tel.: (+49) 9372/132-8976

E-Mail: [email protected]

5WIKA operating instructions pressure transmitter, model MG-1

MM/YYYY country code based on 11609681.02 03/2013 GB/D/F/E

GB

1. General information

Explanation of symbols

WARNING!

... indicates a potentially dangerous situation that can result in serious injury or death,

if not avoided.

CAUTION!

... indicates a potentially dangerous situation, which can result in light injuries or

damage to equipment or the environment, if not avoided.

Information

… points out useful tips, recommendations and information for ecient and trouble-

free operation.

CAUTION!

... indicates a potentially dangerous situation that can result in burns, caused by hot

surfaces or liquids, if not avoided.

Abbreviations

2-wire Two of the connection lines are used for the power supply.

The measurement signal also provides the supply current.

3-wire Two of the connection lines are used for the power supply.

One connection line is used for the measurement signal.

U

B

Positive power terminal

0V Negative power terminal

S

+

Positive measurement terminal

6 WIKA operating instructions pressure transmitter, model MG-1

MM/YYYY country code based on 11609681.02 03/2013 GB/D/F/E

GB

2. Safety

WARNING!

Before installation, commissioning and operation, ensure that the appropriate

pressure transmitter has been selected in terms of measuring range, design and

specic measuring conditions.

Non-observance can result in serious injury and/or damage to the equipment.

Further important safety instructions can be found in the individual chapters of these

operating instructions.

2.1 Intended use

The pressure transmitter is used to convert pressure into an electrical signal.

The pressure transmitter has been designed and built solely for the intended use described here

and may only be used accordingly.

The technical specications contained in these operating instructions must be observed. Improper

handling or operation of the pressure transmitter outside of its technical specications requires

the instrument to be taken out of service immediately and inspected by an authorised WIKA

service engineer.

The manufacturer shall not be liable for claims of any type based on operation contrary to the

intended use.

7WIKA operating instructions pressure transmitter, model MG-1

MM/YYYY country code based on 11609681.02 03/2013 GB/D/F/E

GB

2. Safety

2.2 Personnel qualication

WARNING!

Risk of injury should qualication be insucient!

Improper handling can result in considerable injury and damage to equipment.

The activities described in these operating instructions may only be carried out by

skilled personnel who have the qualications described below.

Skilled personnel

Skilled personnel are understood to be personnel who, based on their technical training, knowl-

edge of measurement and control technology and on their experience and knowledge of country-

specic regulations, current standards and directives, are capable of carrying out the work

described and independently recognising potential hazards.

Special operating conditions require further appropriate knowledge, e.g. of aggressive media.

2.3 Special hazards

WARNING!

For hazardous media such as oxygen, acetylene, ammable or toxic gases or liquids,

and refrigeration plants, compressors, etc., in addition to all standard regulations, the

appropriate existing codes or regulations must also be followed.

WARNING!

Residual media in dismounted instruments can result in a risk to persons, the environ-

ment and equipment.

Take sucient precautionary measures.

8 WIKA operating instructions pressure transmitter, model MG-1

MM/YYYY country code based on 11609681.02 03/2013 GB/D/F/E

GB

2. Safety

2.4 Labelling / safety marks

Product label

If the serial number becomes illegible (e.g. due to mechanical damage or overpainting),

traceability will no longer be possible.

Explanation of symbols

CE, Communauté Européenne

Instruments bearing this mark comply with the relevant European directives.

Voltage DC

Output signal

Pin assignment

Power supply

P# Product No.

S# Serial No.

Model

9WIKA operating instructions pressure transmitter, model MG-1

MM/YYYY country code based on 11609681.02 03/2013 GB/D/F/E

GB

Specications Model MG-1

Measuring range bar 6 10 16 200 300 400

Overpressure safety bar 20 20 32 500 800 800

Burst pressure bar 25 25 160 1200 1700 1700

Measuring range psi 100 150 200 3000 4000 5000

Overpressure safety psi 290 290 460 7200 11000 11000

Burst pressure psi 1450 1450 2300 17000 24000 24000

MPa, kPa and kg/cm² available; -1/0 bar or -30/0 inHg upon request

Level of cleanliness Measuring range < 30 bar/435 psi Measuring range > 30 bar/435 psi

■

Breathing gas free from oil and grease free from oil and grease

- Residual hydrocarbons mg/m² < 1000 < 1000

■

Medical standard per ISO 15001 per ISO 15001

- Residual hydrocarbons mg/m² < 550 < 220

- Particle size µm not applicable on request

■

Industrial standard Free from oil and grease

for oxygen per ASTM Level D/E

and DIN 19247

Free from oil and grease

for oxygen per ASTM Level D/E

and DIN 19247

- Residual hydrocarbons mg/m² < 550 < 220

■

High industrial standard Free from oil and grease for

oxygen per ASTM Level C

Free from oil and grease for

oxygen per ASTM Level C

- Residual hydrocarbons mg/m² < 66 < 66

Materials

■

Process connection 316L and 13-8 PH

■

Case 316L

■

Electrical connection Highly resistant glass-bre reinforced plastic (PBT GF30)

3. Specications

10 WIKA operating instructions pressure transmitter, model MG-1

MM/YYYY country code based on 11609681.02 03/2013 GB/D/F/E

GB

Specications Model MG-1

Output Output signal Power supply U

B

Max. resistive load R

A

4 ... 20 mA, 2-wire DC 8 ... 30 V R

A

≤ (U

B

– 7 V) / 0.02 A

0 ... 10 V, 3-wire DC 14 ... 30 V R

A

> 10 kΩ

0 ... 5 V, 3-wire DC 8 ... 30 V R

A

> 5 kΩ

1 ... 5 V, 3-wire DC 8 ... 30 V R

A

> 5 kΩ

0.5…4.5 V ratiometric DC 5 V ± 5 % R

A

> 4.5 kΩ

Operating current mA max. 10

Settling time ms ≤ 2

Non-linearity % of span ≤ ±0.5 (BFSL) per IEC 61298-2

Accuracy % of span ≤ ±2

1)

Long-term stability % of span ≤ ±0.3 / year

Reference conditions

■

Temperature °C 15 ... 25

■

Humidity % 15 … 95 non-condensing

■

Ambient pressure mmHg 500 … 800

Permissible temperature ranges

■

Operation -20 ... +70 °C -4 ... +158 °F

■

Storage -25 ... +80 °C -13 ... +176 °F

Temperature error in

operating temperature range

% of span ≤ ±2.0

CE conformity

■

Pressure equipment directive 97/23/EC

■

EMC directive 2004/108/EC, EN 61326 Emission (Group 1, Class B) and

Immunity (industrial locations)

3. Specications

11WIKA operating instructions pressure transmitter, model MG-1

MM/YYYY country code based on 11609681.02 03/2013 GB/D/F/E

GB

Specications Model MG-1

Shock resistance g 40 (6 ms) per IEC 60068-2-27 (mechanical shock)

Vibration resistance g 20 (20 ... 2000 Hz, 120 min.) per IEC 60068-2-6

(Vibration under resonance)

Reverse polarity protection U

B

vs. 0V

Short-circuit resistance S

+

vs. 0V

Weight kg approx. 0.08

1) Including non-linearity, hysteresis, zero-point and full scale value deviations (corresponds to measuring error per IEC 61298-2).

Calibrated in vertical mounting position with process connection facing downwards.

3. Specications / 4. Design and function

For special model numbers, e. g. MG-10000, please note the specications stated on the

delivery note.

For further specications, see WIKA data sheet PE 81.44 and the order documentation.

When designing the system, please note that the values given (e.g. burst pressure,

overpressure safety) are dependent upon the material, thread and gasket used.

4. Design and function

4.1 Description

By means of a sensor element and by applying power, the prevailing pressure is converted into an

amplied standardised electrical signal via the deformation of a membrane. This electrical signal

varies in proportion to the pressure and can be evaluated accordingly.

4.2 Scope of delivery

Cross-check scope of delivery with delivery note.

12 WIKA operating instructions pressure transmitter, model MG-1

MM/YYYY country code based on 11609681.02 03/2013 GB/D/F/E

GB

5. Transport, packaging and storage

5.1 Transport

Check the pressure transmitter for any damage that may have been caused during transportation.

Obvious damage must be reported immediately.

A recieved-goods inspection determines the purity of the pressure transmitter. It is only

guaranteed if the packaging is undamaged or unopened.

5.2 Packaging

Do not remove packaging until just before mounting.

Keep the packaging as it will provide optimum protection during transport (e.g. change in

installation site, sending for repair).

5.3 Storage

Permissible conditions at the place of storage:

■

Storage temperature: -25 ... +80 °C

■

Humidity: 15 ... 95 % (no condensation)

Only ever store the pressure transmitter in its original packaging.

WARNING!

Before storing the pressure transmitter (following operation), remove any residual

media. This is of particular importance if the medium is hazardous to health,

e.g. caustic, toxic, carcinogenic, radioactive, etc.

13WIKA operating instructions pressure transmitter, model MG-1

MM/YYYY country code based on 11609681.02 03/2013 GB/D/F/E

GB

6. Commissioning, operation

Required tool: SW 24 open-ended spanner

WARNING!

Prior to commissioning, the pressure transmitter must be subjected to a visual

inspection.

Only use the pressure transmitter if it is in perfect condition with respect to safety.

Making the mechanical connection

■

To ensure that the wetted parts do not get soiled, the protection

cap should not be removed until immediately prior to mounting.

■

Use only BAM-certied gaskets.

■

During mounting, make sure that the sealing faces at the pressure

transmitter and the measuring point are clean and undamaged.

■

Only ever screw in, or unscrew, the pressure transmitter to the

prescribed torque via the spanner-ats, and using tools which are

appropriate and clean for use with oxygen.

The correct torque depends on the dimensions of the process

connection and the gasket used (form/material). When screwing

in or unscrewing the pressure transmitter, do not use the housing or plug for purchase.

■

When screwing in, do not cross the threads.

■

Only lubricate thread with materials approved for use with oxygen.

■

For information on tapped holes and welding sockets, please refer to our Technical Information

IN 00.14 at www.wika.com.

max.

20 Nm

14 WIKA operating instructions pressure transmitter, model MG-1

MM/YYYY country code based on 11609681.02 03/2013 GB/D/F/E

GB

6. Commissioning, operation

Making the electrical connection

■

Ground the pressure transmitter via the process connection.

■

This is Protection Class 3 equipment for connection at low voltages, which are separated from

the power supply or voltage by greater than AC 50 V or DC 120 V. Preferably, a connection

to an SELV or PELV circuit is recommended; alternatively protective measures from

HD 60346-4-41 (DIN VDE 0100-410).

■

Option for North America: The connection can be made in line with "Class 2 Circuits"

or "Class 2 Power Units" in accordance with CEC (Canadian Electrical Code) or

NEC (National Electrical Code).

■

Select a cable diameter that matches the cable gland of the plug. Make sure that the cable

gland of the mounted plug has a tight t. To guarantee the ingress protection, tighten the gland.

■

For cable outlets, make sure that no moisture enters at the cable end.

Types of sealing

per EN 837

per DIN 3852-E

NPT, R and PT

Self-sealing thread typ

15WIKA operating instructions pressure transmitter, model MG-1

MM/YYYY country code based on 11609681.02 03/2013 GB/D/F/E

GB

Electrical connection

Circular connector

M12 x 1, 4-pin

Cable outlet

2 m

Shielded cable outlet

2 m

2-wire U

B

= 1 0V = 3 U

B

= brown 0V = green U

B

= brown 0V = blue

3-wire U

B

= 1 0V = 3 S

+

= 4 U

B

= brown 0V = green S

+

= white U

B

= brown 0V = blue S

+

= black

Wire cross-section

- 3 x 0.14 mm

2

3 x 0.14 mm

2

Cable diameter - 3.6 mm 4.3 mm

Ingress protection

per IEC 60529

IP 67 IP 67 IP 67

The stated ingress protection only applies when plugged-in using line connectors that have

the appropriate ingress protection.

6. Commissioning, operation

Functional check

The output signal must be proportional to the prevailing pressure. If this is not the

case, this may indicate a damaged membrane. In this case, see chapter "8. Faults".

WARNING!

■

Only open the connections once the system has been depressurised

■

Observe the working conditions in accordance with chapter "3. Specications".

■

Always operate the pressure transmitter within the overpressure safety range.

CAUTION!

When touching the pressure transmitter, please note that the surfaces of the device

components can become hot during operation.

16 WIKA operating instructions pressure transmitter, model MG-1

MM/YYYY country code based on 11609681.02 03/2013 GB/D/F/E

GB

7. Maintenance and cleaning

7.1 Maintenance

This pressure transmitter is maintenance-free.

Repairs must only be carried out by the manufacturer.

When performing maintenance work, the purity requirements of the applicable standards must be

observed.

7.2 Cleaning

CAUTION!

■

Before cleaning, correctly disconnect the pressure transmitter from the

pressure supply, switch it o and disconnect it from the mains.

■

Clean the pressure transmitter with a moist cloth.

■

Wash or clean the dismounted pressure transmitter before returning it in order to

protect personnel and the environment from exposure to residual media.

■

Residual media in dismounted pressure transmitters can result in a risk to

persons, the environment and equipment. Take sucient precautionary measures.

■

Do not use any pointed or hard objects for cleaning, as they may damage the

membrane of the process connection.

For information on returning the pressure transmitter see chapter "9.2 Return".

17WIKA operating instructions pressure transmitter, model MG-1

MM/YYYY country code based on 11609681.02 03/2013 GB/D/F/E

GB

Faults Causes Measures

No output signal Cable break Check the through drilling

Deviating zero point signal Overpressure safety exceeded Observe the permissible overpressure

safety (see chapter "3. Specications")

Deviating zero point signal Operating temperature too high/

low

Observe the permissible temperatures

(see Chapter "3. Specications")

Constant output signal upon

change in pressure

Mechanical overload caused by

overpressure

Replace pressure transmitter; if it fails

repeatedly, contact the manufacturer

Signal span too small Mechanical overload caused by

overpressure

Replace pressure transmitter; if it fails

repeatedly, contact the manufacturer

Signal span varies EMC interference sources in

the environment; for example,

frequency converter

Shield the pressure transmitter;

Cable shielding; remove source of interfe-

rence

Signal span varies/inaccurate Operating temperature too high/

low

Observe the permissible temperatures

(see chapter "3. Specications")

Signal span drops/too small Signal span drops/too small Contact manufacturer and replace pressure

transmitter

If complaint is unjustied, we will charge you the complaint processing fees

8. Faults

WARNING!

Open the connections only after the system has been depressurised!

First check whether the system is under pressure and whether the correct power supply and

correct wiring type (2-wire/3-wire) has been selected.

18 WIKA operating instructions pressure transmitter, model MG-1

MM/YYYY country code based on 11609681.02 03/2013 GB/D/F/E

GB

8. Faults / 9. Dismounting, return and disposal

CAUTION!

If deciencies cannot be eliminated by means of the measures listed above, shut

down the instrument immediately, and ensure that pressure and/or signal are no

longer present, and secure the instrument from being put back into operation

inadvertently. In this case, contact the manufacturer. If a return is needed, please

follow the instructions given in chapter "9.2 Return".

9. Dismounting, return and disposal

WARNING!

Residual media in dismounted pressure transmitters can result in a risk to persons,

the environment and equipment.

Take sucient precautionary measures.

9.1 Dismounting

WARNING!

Only disconnect the pressure transmitter once the system has been

depressurised!

9.2 Return

WARNING!

Absolutely observe when shipping the pressure transmitter:

All pressure transmitters delivered to WIKA must be free from any kind of

hazardous substances (acids, leachate, solutions, etc.).

When returning the pressure transmitter, use the original packaging or a suitable transport

package.

19WIKA operating instructions pressure transmitter, model MG-1

MM/YYYY country code based on 11609681.02 03/2013 GB/D/F/E

GB

Enclose the completed returns form with the pressure transmitter.

Information on returns can be found under the heading "Service" on our local website.

9.3 Disposal

Incorrect disposal may endanger the environment.

Dispose of instrument components and packaging materials in an environmentally compatible

way and in accordance with the country-specic waste disposal regulations.

9. Dismounting, return and disposal

20 WIKA operating instructions pressure transmitter, model MG-1

MM/YYYY country code based on 11609681.02 03/2013 GB/D/F/E

GB

Appendix 1: EC Declaration of Conformity for model MG-1

La page charge ...

WIKA MG-1 Mode d'emploi

WIKA MG-1 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents