Electrolux E30MH65QPSA Guide d'installation

Installation

Instructions

Overthe Range

Microwave Oven

I

Questions? Call 1-877-435-3287(US) or 1-800-265-8352(Canada)

I

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT - Savethese

instructions for local inspector's use.

• IMPORTANT - Observeall

governing codes and ordinances.

• Note to Installer - Be sure to leave these

instructions with the Consumer.

• Note to Consumer - Keep these

instructions for flJture reference.

• Skill level - Installation of this appliance requires

basic mechanical and electrical skills.

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not

covered under the Warranty.

READ CAREFU LLY.

KEEP THESE INSTRUCTIONS.

p/n 316902904

January 2014

Installation Instructions

CONTENTS

General information

Important Safety Instructions .................................. 3

Electrical Requirements .......................................... 3

Damage - Shipment/Installation .............................. 4

Parts Included .......................................................... 4

Tools You Will Need ................................................ 5

Mounting Space ...................................................... 5

Step-by-step installation guide

Placement of The Mounting Plate ...................... 6-8

Removing the Mounting Plate ...................... 6

Finding the Wall Studs .................................. 6

Determining Wall Plate Location .................. 7

Aligning the Wall Plate ................................ 8

Installation Types ............................................... 9-22

Hood Exhaust .................................................. 10-11

_ Outside Top ............................

Exhaust 12-15

Attach Mounting Plate to Wall ............ 12

Preparation of Top Cabinet ................ 13

Adapting Microwave Blower for

Outside top Exhaust .................. 13-14

Checking for Proper Damper

Operation ............................................ 14

Mount the Microwave Oven .......... 14-15

Adjust the Exhaust Adaptor ................ 15

Connecting Ductwork .......................... 15

]Outside Back Exhaust 16-19

Preparing Rear Wall for

Outside Back Exhaust .......................... 16

Remove Blower Plate .............................. 16

Attach Mounting Plate to Wall ............ 17

Preparation of Top Cabinet ................ 17

Adapting Microwave Blower

for Outside Back Exhaust ................ 17-18

Mount the Microwave Oven ................ 19

[] Recirculating ........................................

20 _ 2 2

Attach Mounting Plate to Wall ............ 20

Preparation of Top Cabinet ................ 21

Check Blower Plate ............................ 21

Mount the Microwave Oven .......... 21-22

Installing or Change the

Charcoal Filter .................................... 22

Before You Use Your Microwave .......................... 23

Template Information ............................................. 24

EN-2

Installation Instructions

IMPORTANT SAFETY INSTRUCTIONS

This product requires a three-prong grounded outlet.

The installer" must perform a ground continuity check

on the power" outlet box before beginning the

installation to ensure that the outlet box is properly

grounded. If not properly grounded, or" if the outlet

box does not meet electrical requirements noted

(under ELECTRICAL REQUIREMENTS), a qualified

electrician should be employed to correct any

deficiencies.

CAUTION: For personal

safety, remove house fuse

or open circuit breaker

before beginning

installation to avoid severe

or fatal shock injury.

CAUTION: For personal safety, the mounting surface

must be capable of supporting the cabinet load, in

addition to the added weight of this 63-85 pound

(28.5-38.5 kg) product, plus additional oven loads of

up to 50 pounds (22.7 kg) or a total weight of

113-135 pounds (51.3-61.2 kg).

CAUTION: For personal safety, this product cannot

be installed in cabinet arrangements such as an island or

a peninsula. It must be mounted to BOTH a top cabinet

AND a wall.

NOTE: For easier installation and personal safety, it is

recommended that two people install this product.

IMPORTANT - PLEASE READ CAREFULLY. FOR

PERSONAL SAFETY, THIS APPLIANCE MUST BE

PROPERLY GROUNDED TO AVOID SEVERE OR

FATAL SHOCK.

Ensureproper

groundexists

beforeuse

The power cord of this

appliance is equipped with a

three-prong (grounding)

plug which mates with a

standard three-prong

(grounding) wall receptacle

to minimize the possibility

of electric shock hazard

from this appliance.

You should have the wall receptacle and circuit checked

by a qualified electrician to make sure the receptacle is

properly grounded.

Where a standard two-prong wall receptacle is

encountered, it is very important to have it replaced

with a properly grounded three-prong wall receptacle,

installed by a qualified electrician.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT,

DEFORM OR REMOVE ANY OF THE PRONGS

FROM THE POWER CORD. DO NOT USE WITH

AN EXTENSION CORD.

ELECTRICAL

REQUIREMENTS

Product rating is 120 volts AC, 60 Hertz, 15 amps and

1.6 kilowatts. This product must be connected to a

seperate and dedicated supply circuit of the proper

voltage and frequency. Wire size must conform to

the requirements of the National Electrical Code or

the prevailing local code for this kilowatt rating.

The power supply cord and plug shotfld be brought to a

seperate and dedicated 15- to 20- ampere branch

circtfit single grounded outlet. The outlet box should

be located in the cabinet above the microwave oven.

The outlet box and supply circuit should be installed

by a qualifed electrician and conform to the

National Electrical Code or the prevailing local code.

EN-3

Installation Instructions

DAMAGE--SHIPMENT/

INSTALLATION

• If the unit is damaged in shipment, return the

unit to the store in which it was bought for repair

or replacement.

• If the unit is damaged by the customer, repair or

replacement is the responsibility of the customer.

• If the unit is damaged by the installer (if other

than the customer), repair or replacement must

be made by arrangement between customer

and installer

PARTS INCLUDED

HARDWARE PACKET

PART

/

+

!

Wood Screws

(1/4" X 2")

ToggleBolts(and

wingnuts)(3/16"x3")

Sel?AligningMachine

Screws(1/4"-28x 31/4'')

NylonGrommet

(formetalcabinets)

QUANTITY

2

You will find the installation hardware contained in

a packet with the unit. Check to make sure you have

all these parts.

NOTE: Some extra parts are included.

PARTS INCLUDED (CONT.)

ADDITIONAL PARTS

PART QUANTITY

Forsome models

TopCabinet

Template

RearWall

Template

Installation

Instructions

Use&Care

Manual

Grease

Filters

Exhaust

adaptor

Glass

Tray

Turntable

Ring

Convection

wire rack

Shelf

EN-4

Installation Instructions

TOOLS YOU WILL NEED

# 1Phillipsscrewdriver

f

Tinsnips(forcutting

damper,if required)

Gloves

Safetygoggles

Pencil

Scissors

(tocuttemplate,if necessary)

din:=

Saw(saber,holeor keyhole)

Ruleror tapemeasureand

t edge

Electricdrill with s/16",1/2"and%"

drill bits

Studfinder or Hammer(optional)

Level

Carpentersquare

(optional)

Fillerblocksor scrap

woodpieces,if needed

fortop cabinetspacing

(usedonrecessedbottom

cabinetinstallationsonly)

Ductandmaskingtape

MOUNTING SPACE

J

3O

_12cm)

mlrl.

BottomEdgeof

CabinetNeedsto

be30"(76.2cm)

or Morefromthe

CookingSurface

)lash

NOTES:

• The space between the cabinets must be

30" (76.2 cm)wide and free of obstructions.

• If you are going to vent your microwave oven

to the outside, see Hood Exhaust Section for

exhaust duct preparation.

• When installing the microwave oven beneath

smooth, flat cabinets, be careful to follow the

instructions on the top cabinet template for

power cord clearance.

• As a guide to installation, see page 24 for Mounting

Template Information.

66" (167.6cm)

or Morefrom

the Floortothe

Topofthe

Microwave

x

Cabinet Cabinet

EN-5

Installation Instructions

PLACEMENT OF THE MOUNTING PLATE

I-_ REMOVING THE MICROWAVE

OVEN FROM THE CARTON/

REMOVING THE MOUNTING

PLATE

Remove the installation instructions,use and care,

exhaust adapter, turntable ring, shelf, glass

tray and the small hardware bag. Do not remove

the Styrofoam protecting the front of the oven.

Small Hardware Bag

Turntable Ring below

glass tra

Exhaust Adapter

lelf

Glass Tray

[] Fold back all 4 carton flaps fully against carton

sides. Then carefully roll the oven and carton over

onto the top side. The oven should be resting in

the Styrofoam.

[] Pull the carton up and off the oven.

[] Cut the middle of the outer protective plastic bag to

remove the mounting plate

Screws Screws

_r Mounting Plate '_

Remove the screws from each end of the mounting

plate. This plate will be used as the rear wall template

and for mounting. Reinstall the screws into the holes

where they were removed.

I-_ FINDING THE WALL STUDS

[] Find the studs, using one of the following

methods:

A. Stud finder - a magnetic device which

locates nails.

B. Use a hammer to tap lightly across the

mounting surface to find a solid sound.

This will indicate a stud location.

_}_ After locating the stud (s), find the center by

probing the wall with a small nail to find the edges

of the stud. Then place a mark halfway between

the edges. The center of any adjacent studs should

be 16" (40.6 cm) or 24" (61 cm) from this mark.

[] Draw a line down the center of the studs.

THE MICROWAVE MUST BE CONNECTED TO

AT LEAST ONE WALL STUD.

EN-6

Installation Instructions

I-_ DETERMINING WALL PLATE LOCATION U NDER YOUR CABINET

Plate position-beneath flat bottom

cabinet

,'i L L

t

17 1,2,,

i IJ C !ll . .

i_ Iii I Draw a vertical line on

-_ _ the wall at the center of

At least 30" _ the 30" wide space,

Tape the Rear Wall

Template onto the wall

matching the centerline

and touching the

bottom of the cabinet,

Plate position-beneath framed

recessed cabinet bottom

I

I I

30" to Cooktop

Draw a vertical line on the wall at the center of the

30" space.

Tape the Rear Wall Template onto the wall

matching the centerline and touching the bottom

cabinet frame.

Plate position-beneath recessed

bottom cabinet with front overhang

Draw a line on the

back wall equal to the

depth of the front

overhang.

Your cabinets may have decorative trim that

interferes with the microwave installation. Remove

the decorative trim to install the microwave properly

and to make it level.

THE MICROWAVE MUST BE LEVEL.

Use a level to make sure the cabinet bottom is level.

If the cabinets have a front overhang only, with no

back or side frame, install the mounting plate down

the same distance as the front overhang depth. This

will keep the microwave level.

I_ Measure the inside depth of the front overhang.

I_ Draw a horizontal line on the back wall an equal

distance below the cabinet bottom as the inside

depth of the front overhang.

I_ For this type of installation with front overhang

only, align the mounting tabs with this horizontal

line, not touching the cabinet bottom as described

in Step D.

EN-7

Installation Instructions

ALIGNING THE WALL PLATE

Centerline Draw a Vertical Line

Hole B notches on Wall from Center

of Top Cabinet

Horizontal Line

CAUTION: Wear gloves

to avoid cutting fingers on

sharp edges.

!

Area E

HoleA Horizontal Line

Draw a horizontal line on wall at the

bottom of "Rear Wall Template".

_!_ Draw a vertical line on the wall at the center of the

30" wide space.

L_JDraw a horizontal line on the wall at the bottom of

"Rear Wall Template".

[_ Find a wall stud in area "E" of mounting plate

Refer to section lB. Finding the wall studs.

For attaching the mounting plate into stud drill

a 3/16" hole into wood stud. Drill a 5/8" hole for

toggle bolt in 1 other location (Hole A or Hole B)

NOTE: DO NOT MOUNT THE PLATE AT THIS

TIME.

NOTE: Holes A and B are inside area E. If neither of

Holes A and B are not in a stud, find a stud somewhere

in area E and draw a circle to line up with the stud. It is

important to have at least one wood screw mounted

firmly in a stud to support the weight of the

microwave. Set the mounting plate aside.

EN-8

Installation Instructions

INSTALLATION TYPES

This microwave oven is designed for adaptation to

the following three types of ventilation:

A. Outside Top Exhaust (Vertical Duct)

B. Outside Back Exhaust (Horizontal Duct)

C. Recirculating (Non-Vented Ductless)

(Choose A, B or C)

NOTE: This microwave is shipped assembled for

Recirculating. Select the type of ventilation required

for your installation and proceed to that section.

OUTSIDE TOP EXHAUST

(VERTICAL DUCT)

OUTSIDE BACK EXHAUST

(HORIZONTAL DUCT)

AdaptorinPlacefor

OutsideTopExhaust

Adaptor Must Be

Moved to the Backfor

OutsideBackExhaust

RECIRCULATING

(NON-VENTED DUCTLESS)

Models are shipped for

recirculating exhaust.

Some models have a

disposable charcoal filter

installed to help remove

smoke and odors.

NOTE: Read the next two pages only if you plan to vent your exhaust to the

outside. If you plan to recirculate the air back into the room, proceed to page 20.

EN-9

Installation Instructions

INSTALLATION INSTRUCTIONS FOR EXTERNAL EXHAUST DUCTING

NOTE: If you need to install ducts, note that the total

duct length of 31/4" x 10" (8.2 x 25.4 cm) rectangular or

5" (12.7 cm) diameter/ 6" (15.2 cm) diameter round duct

should not exceed 120 equivalent feet (36.5 m).

Outside ventilation requires an EXTERNAL EXHAUST

DUCT.Read the following carefully.

NOTE: It is important that venting be installed using

the most direct route and with as few elbows as possible.

This ensures clear venting of exhaust and helps prevent

blockages. Also, make sure dampers swing freely and

nothing is blocking the ducts.

Exhaust connection:

The exhaust adaptor has been designed to mate with

a standard 31/4" x 10" (8.2 x 254 cm) rectangular duct.

If a round duct is required, a rectangular-to-round

transition adaptor must be used. A 5" (12.7cm)/6" (15.2cm)

diameter duct is acceptable to use.

Maximum duct length:

For satisfactory air movement, the total duct length of

31/4'' x 10" (8.2 x 25.4 cm) rectangular or 5" (12.7 cm)

diameter/6 "(15.2 cm) diameter round duct should not

exceed 120 equivalent feet (36.5 m).

Elbows, transitions, wall and roof caps,

etc., present additional resistance to airflow and are

equivalent to a section of straight duct which is longer

than their actual physical size. When calculating the total

duct length, add the equivalent lengths of all transitions

and adaptors plus the length of all straight duct sections.

The chart below shows you how to calculate total

equivalent ductwork length using the approximate feet

of equivalent length of some typical ducts.

DUCT PIECES

J

@

0

J

Rectangular-to-Round

TransitionAdaptor*

Wall Cap

90° Elbow

45° Elbow

90° Elbow

45° Elbow

RoofCap

StraightDuct6" (15,2cm)

Roundor31/4``x 10"

(8,2x25,4cmRectangular)

EQUIVALENT

LENGTH

5 Ft,(1,5m)

40Ft,(12,2m)

10Ft,(3m)

5 Ft,(1,5m)

25Ft,(7,6m)

5 Ft,(1,5m)

24Ft,(7,3m)

1 Ft,(0,3m)

NUMBER

x USED

x ()

Total Ductwork

EQUIVALENT

LENGTH

Ft,orm

Ft. or m

* IMPORTANT: If a rectangular to round transition

adaptor is used, the bottom corners of the damper

will have to be cut to fit, using the tin snips, in order

to allow free movement of the damper.

Equivalent lengths of duct pieces are based on actual tests

and reflect requirements tot good venting perti}rmance with

any vent hood.

EN-IO

Installation Instructions

EXTERNAL EXHAUST DUCTING

OUTSIDE TOP EXHAUST (EXAMPLE ONLY)

The following chart describes an example of one possible

ductwork installation.

DUCT PIECES

Roof Cap

EQUIVALENT NUMBER EQUIVALENT

LENGTH x USED = LENGTH

24Ft,(7,3m) x (1) 24Ft,(7,3m)

12Ft,(3,6m)StraightDuct 12 Ft,(3,6m) x (1) = 12 Ft,(3,6m)

(6'715,2cmRound)

Rectangular-to-Round 5 Ft,(1,5m) x (1) = 5 Ft,(1,5m)

TransitionAdaptor*

Equivalentlengthsofductpiecesarebasedonactualtestsand

reflectrequirementsfor goodventingperformancewith anyvent hood,

Total Length = 41 Ft. (12.5 m)

* IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper

will have to be cut to fit, using the tin snips, ira order to allow free movement of the damper:

OUTSIDE BACK EXHAUST (EXAMPLE ONLY)

The following chart describes an example of one possible

ductwork installation.

EQUIVALENT NUMBER EQUIVALENT

LENGTH* USED = LENGTHDUCT PIECES x

_:[_ Cap (12,2m) x

Wall 40Ft,

3Ft,StraightDuct 3Ft,(0,9m) x

(31/i'x 10'78,2x25,4cm

Rectangular)

(_ 90° Elbow 10Ft,(3m) x

(1) 40Ft,(12,2m)

(1) = 3Ft,(0,9m)

(2) = 20Ft,(3 m)

Equivalentlengthsof ductpiecesarebasedonactualtests and

reflectrequirementsfor goodventingperformancewith anyventhood,

Total Length = 63 Ft. (19.2 m)

NOTE: For- back exhaust, care should be taken to align exhaust with space between studs, or"wall should be prepared

at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust.

EN-11

Installation Instructions

F-A OUTSIDE TOP EXHAUST (Vertical Duct)

INSTALLATION OVERVIEW

A1. Attach Mounting Plate to Wall

A2. Prepare Top Cabinet

A3. Adapting Microwave Blower for

Outside Top Exhaust

A4. Check Damper Operation

A5. Mount Microwave Oven

A6. Adjust Exhaust Adaptor

A7. Connect Ductwork

IMPORTANT NOTES:

• Make sure the screws for the

blower motor and blower plate

are securely tightened when

they are reinstalled. This will _ _ ......help to prevent excessive __ ......

vibration.

• Make sure the motor wiring has -'_

been properly routed and secured,

and that the wires are not pinched.

IMPORTANT :Do not remove the cardboard

spacers between the heat shield and door.

_-_ ATTACH THE MOUNTING

PLATE TO THE WALL

W ..... ,t . .

i

_J

Attach the plate to the wall using toggle bolts.

At least one wood screw must be used to attach

the plate to a wall stud.

_ Remove the from the bolts.

toggle wings

_ Insert the bolts into the mounting plate

through the holes designated to go into drywall

and reattach the toggle wings to 3/4" (19 mm) onto

each bolt.

To use toggle bolts:

Mounting

Plate.

Spacing for Toggles

More Than Wall

_@,__[____Thickness

I

lToggle Wings

Bolt End

_ lace the mounting plate against the wall and

insert the toggle wings into the holes in the wall

to mount the plate.

NOTE: Before tightening toggle bolts and wood

screw, make sure the bottom of the mounting plate

touch the bottom of the cabinet when pushed

flush against the wall and that the plate is properly

centered under the cabinet.

CAUTION: Be careful to avoid pinching fingers

between the back of the mounting plate and the wall.

_ Tighten all bolts. Pull the plate away from the wall

to help tighten the bolts.

EN-12

Installation Instructions

I-_ USE TOP CABINET TEMPLATE

FOR PREPARATION OF TOP

CABINET

You need to drill holes for the top support screws, a

hole large enough for the power cord to fit through,

and a cutout large enough for the exhaust adaptor.

• Read the instructions on the TOP CABINET

TEMPLATE.

• Tape it underneath the top cabinet.

• Drill the holes, following the instructions on the

TOP CABINET TEMPLATE.

CAUTION: Wear safety goggles when drilling holes

in the cabinet bottom.

ADAPTING MICROWAVE

BLOWER FOR OUTSIDE

TOP EXHAUST

] lace the microwave in its upright position,

with the top of the unit facing up.

Blower Plate

Backof

_-_Microwave

O_

- Blower Motor

Screw

Remove the screw that holds the blower plate

to the microwave. Remove and save the screw

holding the blower motor to the microwave.

Careflflly pull out the blower unit. The wires

will extend far enough to allow you to adjust

the blower unit.

EndA__End B

Microwave

Roll the blower unit 90 ° so that fan blade

openings are facing out the top of the

microwave.

Before Rotation After Rotation

Backof

Microwave Microwave

[]Place the blower unit back into the opening.

Backof

Microwave

CAUTION: Do not pull or stretch the blower

unit wiring. Make sure the wires are not

pinched, and that they are properly secured.

EN-13

Installation Instructions

ADAPTING MICROWAVE

BLOWER FOR OUTSIDE

TOP EXHAUST

Secure blower unit to microwave with the screw

removed in Step 1. Make sure the screw is tight.

Replace blower plate with the screw removed in

Step 1. Make sure the screw is tight.

T

I

Backof

Microwave

[]

Attach the exhaust adaptor to the top of the

blower plate by sliding it into the guides of the

blower plate.

Adaptor

k0cking Tab

Push in securely until it is in the locking tabs.

Take care to assure that the damper hinge is

installed so that the damper swings freely.

I-_ CHECK FOR PROPER

DAMPER OPERATION

Blower Plate Exhaust Adaptor

X ,,_-___----Damper

• Make sure tape securing damper is removed and

damper pivots easily before mounting microwave.

• You will need to make adjustments to assure proper

alignment with your house exhaust duct after the

microwave is installed.

I-_ MOUNT THE MICROWAVE

OVEN

FOR EASIER INSTALLATION AND PERSONAL

SAFETY, WE RECOMMEND THAT TWO PEOPLE

INSTALL THIS MICROWAVE OVEN.

IMPORTANT: Do not grip or use the handle

or heat shield during installation. Do not

remove the cardboard spacers between the

heat shield and door.

NOTE: If your cabinet is metal, use tim nylon

grommet around the power cord hole to prevent

cutting of the cord.

NOTE: We recommend using filler blocks if the

cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are

not used, case damage may occur from

overtightening screws.

NOTE: When mounting the

microwave oven, thread

power cord through hole in

bottom of top cabinet. Keep

it tight throughout Steps

1-3. Do not pinch cord or

lift oven by pulling cord.

[]Lift tilt it

microwave,

forward, and hook

slots at back bottom

edge onto four lower

tabs of mounting

plate.

[]Rotate front of

oven

up against cabinet

bottom.

[]Insert a self-aligning screw through top center

cabinet hole. Temporarily secure the oven by

turning the screw at least two full turns after the

threads have engaged. (It will be completely

tightened later.) Be sure to keep power cord

tight. Be careful not to pinch the cord, especially

when mounting flush to bottom of cabinet.

EN-14

Installation Instructions

MOUNT THE MICROWAVE

OVEN (cont.)

Cabinet Front

Cabinet Bottom Shelf

_ ;Z_._ Filler Block

IT_fflT-,_111-"T Equiva,ent

'/llNt/] [t/I /toDepth

!\\1 IU_-_ Self-Aligning Screw

Microwave Oven Top

[]Attach the microwave oven to the top cabinet.

[] Insert 2 self-aligning screws

through outer top cabinet

holes. Turn two full turns on

each screw.

[] Tighten center

screw completely.

[] Tighten the outer two screws to the top of the

microwave oven. (While tightening screws, hold

the microwave oven in place against the wall and

the top cabinet.)

[] Install grease filters. See the Owner's IV_anual

packed with the microwave.

ADJUST THE EXHAUST

ADAPTOR

Open the top cabinet and adjust the exhaust adaptor

to connect to the house duct.

Back of

Blower Plate Damper Microwave

Side-to-Side Adjustment,

Slide the Exhaust Adaptor

as Needed

I-_ CONNECTING DUCTWORK

House Duct

H

]Extend the house duct down to connect to

the exhaust adaptor.

}_ eal exhaust duct joints using furnance duct tape

for t_gh temperature applications.

IMPORTANT: Remove the cardhoard spacers between

heat shield and door.

EN-15

Installation Instructions

OUTSIDE BACK EXHAUST (Horizontal Duct)

INSTALLATION OVERVIEW

BI. Prepare Rear Wall

B2. Remove Blower Plate

B3. Attach Mounting Plate to Wall

B4. Prepare Top Cabinet

B5. Adjust Blower

B6. Mount the Microwave Oven

IMPORTANT NOTES:

• Make sure the screws for the

blower motor and blower plate

are securely tightened when

they are reinstalled. This will _ _ .......

help to prevent excessive __ ......

vibration.

• Make sure the motor wiring has

been properly routed and secured,

and that the wires are not pinched.

IMPORTANT :Do not remove the cardboard

spacers between the heat shield and door.

PREPARING THE REAR WALL

FOR OUTSIDE BACK EXHAUST

You need to cut an opening in the rear wall for

outside exhaust.

• Read the instructions on the REAR

WALL TEMPLATE.

• Tape it to the rear wall.

• Cut the opening, following the instructions of the

REAR WALL TEMPLATE.

REMOVE BLOWER PLATE

Remove and save the screw that holds the blower

plate to the microwave. Lift off the blower plate.

Blower Plate

i

Backof

Microwave

EN-16

Installation Instructions

_] ATTACH THE MOUNTING

PLATE TO THE WALL

Attach the plate to the wall using toggle bolts.

At least one wood screw must be used to attach

the plate to a wall stud.

]Remove the toggle wings from the bolts.

}_ nsert the bolts into the mounting plate through

the holes designated to go into drywall and reattach

the toggle wings to 3/4" (19 mm) onto each bolt.

To use toggle bolts:

Mounting

Plate

Spacing for Toggles More

_-_i_,---Than Wall Thickness

JoggleWings

Bolt End

]Place the mounting plate against the wall and

insert the toggle wings into the holes in the wall

to mount the plate.

NOTE: Before tightening toggle bolts and wood

screw, make sure the bottom of the mounting plate

touch the bottom of the cabinet when pushed flush

against the wall and that the plate is properly

centered under the cabinet.

CAUTION: Be careflfl to avoid pinching fingers

between the back of the mounting plate and the wall.

Tighten all bolts. Pull the plate away from the wall

to help tighten the bolts.

USE TOP CABINET TEMPLATE

FOR PREPARATION OF TOP

CABINET

You need to drill holes for the top support screws and

a hole large enough for the power cord to fit through.

• Read the instructions on the TOP CABINET

TEMPLATE.

• Tape it underneath the top cabinet.

• Drill the holes, following the instructions on the

TOP CABINET TEMPLATE.

CAUTION: Wear safety goggles when drilling holes

in the cabinet bottom.

ADAPTING MICROWAVE

BLOWER FOR OUTSIDE

BACK EXHAUST

[]Remove and that holds blower motor

save screw

to microwave.

Blower Motor

"_" - _ Blower Motor

v .,_ Screw

Careflflly pull out the blower unit. The wires

will extend far enough to allow you to adjust

the blower unit.

EndA

EN-17

Installation Instructions

ADAPTING MICROWAVE

BLOWER FOR OUTSIDE

BACK EXHAUST (cont.)

[] Roll the blower" unit 90 °

Before Rotation After Rotation

Microwave

Backof

Microwave

Rotate blower unit counterclockwise 180 °.

Before Rotation

Backof

Microwave

After Rotation

Microwave

[]Gently remove the wires from the

grooves.

Reroute the wires through grooves on other side

of the blower unit.

Before Rerouting After Rerouting

Wires Routed ThroughRight Side Wires Routed Through Left Side

_6_ Roll the blower unit 90 ° so that fan blade

openings are facing out the back of the

microwave.

Before Rolling

Microwave

After Rolling

Back of

Microwave

[]Place the blower unit back into the opening.

EndA

End

CAUTION: Do not pull or stretch the blower

unit wiring. Make sure the wires are not

pinched, and that they are properly secured.

NOTE: The blower unit exhaust

openings should match exhaust

openings on rear of microwave oven.

[ ecure the blower unit to the microwave with

the original screw.

_, Blower Plate

I _ Backof

,11_ Microwave

Blower Motor

Screw

[]Replace the blower in theplate

same

position

as before with the screw. Make sure the screw

is tight.

[]Attach the exhaust the of theadaptor

to Fear

oven by sliding it into the guides at the top

center of the back of the oven.

Adaptor

Backof

Microwave

o

Locking Tabs

Guide

Push in securely until it is in the lower locking

tabs. Take care to assure that the damper hinge

is installed so that it is at the top and that the

damper swings freely.

EN-18

Installation Instructions

MOUNT THE MICROWAVE

OVEN

FOR EASIER INSTALLATION AND PERSONAL

SAFETY, WE RECOMMEND THAT TWO PEOPLE

INSTALL THIS MICROWAVE OVEN.

IMPORTANT: Do not grip or use the handle

or heat shield during installation. Do not

remove the cardboard spacers between the

heat shield and door.

NOTE: If your cabinet is metal, use the nylon

grommet around the power cord hole to prevent

cutting of the cord.

NOTE: We recommend using filler blocks if the

cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not

used, case damage may occur from

overtightening screws.

NOTE: When mounting the

microwave oven, thread

power cord through hole in

bottom of top cabinet. Keep

it tight throughout Steps

1-3. Do not pinch cord or

lift oven by pulling cord.

[]Lift tilt it

microwave,

forward, and hook

slots at back bottom

edge onto four lower

tabs of mounting

plate.

[] front of

oven

up against cabinet

bottom.

[]Insert a self-aligning screw through top center

cabinet hole. Temporarily secure the oven by

turning the screw at least two full turns after the

threads have engaged. (It will be completely

tightened later:) Be sure to keep power cord

tight. Be careful not to pinch the cord, especially

when mounting flush to bottom of cabinet.

Cabinet Front

Cabinet Bottom Shelf

Filler Block

Equivalent

to Depth

of Cabinet

Recess

Self-AligningScrew

Microwave OvenTop

[]Attach the microwave oven to the top cabinet.

[] Insert 2 self-aligning screws

through outer top cabinet

holes. Turn two full turns on

each screw.

?

u

6_ Tighten center

screw completely.

[] Tighten the outer two screws to the top of the

microwave oven. (While tightening screws, hold

the microwave oven in place against the wall and

the top cabinet.)

[] Install grease filters. See the Owner's Manual

packed with the microwave.

IMPORTANT: Remove the cardhoard spacers between

heat shield and door.

EN-19

Installation Instructions

RECIRCULATING (Non-Vented Ductless)

INSTALLATION OVERVIEW

C1. Attach Mounting Plate to Wall

C2. Prepare Top Cabinet

C3. Check Blower Plate

C4. Mount the Microwave Oven

C5. Install or change Charcoal Filter

IMPORTANT NOTES:

• Make sure the screws for the blower motor and blower

plate are securely tightened when they are reinstalled.

This will help to prevent excessive vibration.

• Make sure the motor wiring has been properly route(

and secured, and that the wires are not pinched.

IMPORTANT :Do not remove the cardboard

spacers between the heat shield and door.

ATTACH THE MOUNTING

PLATE TO THE WALL

Attach the plate to the wall using toggle bolts.

At least one wood screw must be used to attach

the plate to a wall stud.

NOTE: If the cabinet depth including the cabinet doors

is more than 13" then the unit must be spaced

out from wall using adequate materials supporting

150 Ibs to allow proper top vent air exhaust.

[]Remove the from the bolts.

toggle wings

Insert the bolts into the mounting plate through

the holes designated to go into drywall and

reattach the toggle wings to 3/4" (19 mm) onto

each bolt.

To use toggle bolts:

Mounting

Plate

Spacing for Toggles

More Than Wall

_l_!_,..--Thickness

I

l Toggle Wings

Bolt End

]Place the mounting plate against the wall and

insert the toggle wings into the holes in the wall

to mount the plate.

NOTE: Before tightening toggle bolts and wood

screw, make sure the bottom of the mounting plate

touch the bottom of the cabinet when pushed flush

against the wall and that the plate is properly

centered under the cabinet.

CAUTION: Be careflfl to avoid pinching fingers

between the back of the mounting plate and the wall.

Tighten all bolts. Pull the plate away from the wall

to help tighten the bolts.

EN-20

La page charge ...

Electrolux E30MH65QPSA Guide d'installation

Ce manuel convient également à

Electrolux E30MH65QPSA Guide d'installation

dans d''autres langues

Documents connexes

Autres documents