Simplicity SNOWTHROWER, SINGLE STAGE, STANDARD, SEARS CRAFTSMAN 7.5/22 (C950-52482-0) Manuel utilisateur

Not for

Reproduction

Operator’s Manual

Single Stage Snowthrower

Model No. C950-52482-0 (1696553-00)

CAUTION: Before using this product, read the manual and

follow all its Safety Messages and Operating Instructions.

Sears Canada Inc., Toronto, Ontario M5B 2C3

Visit our Craftsman website: www.sears.ca/craftsman

80010861

Revision A

Not for

Reproduction

2

Manual Contents

Thank You Statement ........................................................2

ID Tag and Location ...........................................................2

Operator Safety ..................................................................3

Safety Decals ......................................................................8

Safety System Tests ..........................................................9

Features and Controls .................................................... 10

Operation ......................................................................... 11

Maintenance .................................................................... 16

Troubleshooting .............................................................. 20

Specifications .................................................................. 21

Warranty ........................................................................... 22

The images in this document are representative, and are

meant to complement the instructional copy they accompany.

Your unit may vary from the images displayed. LEFT and

RIGHT are as seen from the operator’s position.

Thank you for purchasing this quality-built CRAFTSMAN®

Snowthrower. We’re pleased that you’ve placed your con-

dence in the CRAFTSMAN brand. When operated and main-

tained according to the manuals, your CRAFTSMAN product

will provide many years of dependable service.

The manuals contain safety information to make you aware

of the hazards and risks associated with the unit and how to

avoid them. This Snowthrower was designed to be used as

described in operator’s manual and is not intended for any

other purpose. It is important that you read and understand

the instructions thoroughly before attempting to start or oper-

ate this equipment. Save these original instructions for

future reference.

This product requires nal assembly before use. Refer to the

setup guide for instructions on nal assembly procedures.

Follow the instructions completely.

Product Model Number:

Product Serial Number:

Engine Model-Type Number:

Engine Code/Serial Number:

Date of Purchase:

Purchase Location:

When contacting your authorized dealer for replacement

parts, service, or information you MUST have these

numbers.

Record your model name/number, manufacturer’s

identification numbers, and engine serial numbers in the

space provided for easy access. These numbers can be

found in the locations shown.

USA

XXXXX

For Parts and Service Call

Pour des pices et l’intervention

SEARS CANADA INC.

Toronto, Ontario M5B2C3

MODEL / MODÈLE

SERIAL NO. / NO. SÉRIE

Assembled In

Rassemblé dans

PRODUCT IDENTIFICATION /

IDENTIFICATION DE PRODUIT

XXXXXXXXXXXXXXXXXXXX

XXXXXXX - XX

XXXXXXXXX

XXX-XXX-XXXX

WWW.XXXXXX.COM

X X X X X X X X X X X X

THANK YOU STATEMENT

ID TAG AND LOCATION

Not for

Reproduction

3

English

en

The product identification tag (A) can be found in the

location shown in Figure 1.

A

Hazard Symbols and Meanings

Read the Operator’s Manual

Remove key before performing

maintenance

Carbon monoxide poisoning hazard

Fire hazard

Explosion hazard

Kickback hazard

Hot surface hazard

Wear safety glasses

Thrown objects hazard

Amputation hazard - rotating impeller

Amputation hazard - rotating auger

OPERATOR SAFETY

Safety Alert Symbol and Signal Words

The safety alert symbol is used to identify safety

information about hazards that can result in personal injury.

A signal word (DANGER, WARNING, or CAUTION) is used

with the alert symbol to indicate the likelihood and potential

severity of injury. In addition, a hazard symbol may be used

to represent the type of hazard.

DANGER indicates a hazard which, if not avoided,

will result in death or serious injury.

WARNING indicates a hazard which, if not avoided,

could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided,

could result in minor or moderate injury.

NOTICE indicates an action that could result in

damage to the product.

A

1

Not for

Reproduction

4

Entanglement hazard - rotating parts

Electric shock hazard

Keep safe distance away

Keep children away

WARNING

• Hand contact with the rotating impeller inside the

discharge chute is the most common cause of injury

associated with snowthrowers.

• This snowthrower is capable of amputating hands

and feet, and throwing objects. Read and observe all

the safety instructions in this manual. Failure to do so

could result in death or serious injury.

WARNING

• Save these original instructions for future reference.

• Be thoroughly familiar with the controls and the

proper use of the snowthrower.

• Make sure you are properly trained before operating

the snowthrower.

• Know how to stop the unit and disengage the controls

quickly.

• Never allow anyone to operate the snowthrower

without proper instruction.

• Always follow the instructions in the operator’s

manual, if the snowthrower will be stored for an

extende d period.

• Maintain or replace safety and instruction labels as

necessary.

• Never attempt to make major repairs on the

snowthrower unless you have been properly trained.

Improper servicing of the snowthrower can result

in hazardous operation, equipment damage, and

voiding of the product warranty.

Read, understand, and follow all the

instructions on the snowthrower and in the

operator’s manual before operating this

unit.

Failure to observe the safet y instructions in

this manual could result in death or serious

injury.

Discharge chute contains rotating impeller

to throw snow. Never clear or unclog the

discharge chute with your hands. Fingers

can quickly become caught in the impeller.

Always use a clean-out tool.

Failure to observe these safety

instructions will result in traumatic

amputation or severe laceration.

DANGER

• Whenever cleaning, repairing, or inspecting the

snowthrower, make sure the engine is OFF, spark

plug wire is disconnected, and all moving parts have

stopped.

• Do not put hands or feet near or under rotating parts.

Keep clear of the discharge opening at all times.

• Never operate the snowthrower without proper

guards, and other safety devices in place and

working.

• Never leave the snowthrower unattended while

engine is running. Always disengage the auger and

traction controls, stop engine, and remove keys.

• Keep all loose clothing away from the front of

the snowthrower and auger. Scarves, mittens,

dangling drawstrings, loose clothes, and pants can

quickly become caught in the rotating device and

amputation will occur. Tie up long hair and remove

jewelry.

• Run the machine a few minutes after discharging

snow to prevent freeze-up of the collector/impeller.

• Disengage power to the collector/impeller when

snowthrower is transported or not in use.

Keep hands, feet, and clothing away from

rotating parts. Rotating parts can contact

or entangle hands, feet, hair, clothing, or

accessories.

Failure to observe these safety

instructions will result in traumatic

amputation or severe laceration.

Not for

Reproduction

5

English

en

WARNING

• Always wear safety glasses or eye shields during

operation, and while performing an adjustment or

repair.

• Always be aware of the direction the snow is being

thrown. Nearby pedestrians, pets, or property may

be harmed by objects being thrown.

• Be aware of your environment while operating the

snowthrower. Don’t run over items such as gravel,

doormats, newspapers, toys, and rocks hidden

under snow, as they can all be thrown from the

chute or jam in the auger.

• Use extreme caution when operating on or crossing

gravel drives, walks, or roads.

• Adjust the collector housing height to clear gravel or

crushed rock surface.

• Never operate the snowthrower near glass

enclosures, automobiles, window wells, drop-

offs, and the like without proper adjustment of the

discharge chute angle.

• Familiarize yourself with the area in which you plan

to operate the snowthrower. Mark off boundaries of

walkways and driveways.

Objects can be picked up by auger and

thrown from chute. Never discharge snow

toward bystanders or allow anyone in front

of the snowthrower. Failure to observe

these safety instructions will result in death

or serious injury.

WARNING

• Keep children out of the area during operation.

Children are often attracted to the equipment. Be

mindful of all persons present.

• Be alert and turn unit off if children enter the area.

• Never allow children to operate the unit.

• Use extra care when approaching blind corners,

shrubs, trees, or other objects that may obscure

vision. Children may be present.

Tragic accidents can occur if the operator

is not alert to the presence of children.

Children are often attracted to the unit and

the operating activity. Never assume the

children will remain where you last saw

them.

Engines give off carbon monoxide, an

odorless, colorless, poison gas. Breathing

carbon monoxide can cause nausea,

fainting, or death.

WARNING

• Start and run engine outdoors.

• Do not run the engine in an enclosed area, even if

doors or windows are open.

WARNING

When Adding Fuel

• Turn off engine and let cool at least 2 minutes

before removing the fuel cap and adding fuel.

• Fill fuel tank outdoors or in a well ventilated area.

• Do not overfill the fuel tank. To allow for the

expansion of gasoline, do not fill above the bottom

of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot

lights, heat, and other ignition sources.

• Check fuel lines, cap, and fittings frequently for

cracks or leaks. Replace if necessary.

• Use an approved fuel container.

• If fuel spills, wait until it evaporates before starting

engine.

When Starting Engine

• Ensure that spark plug, muffler, fuel cap, and air

cleaner (if equipped) are in place and secured.

• Do not crank the engine with the spark plug

removed.

• If fuel is spilled, do not attempt to start the engine,

but move the snowthrower away from the area of

the spill, and avoid creating any source of ignition,

until the fuel vapors have dissipated.

• Do not over-prime the engine. Follow the engine

starting instructions in this manual.

• If the engine floods, set choke (if equipped) to

OPEN/RUN position, move throttle (if equipped) to

FAST position and crank until engine starts.

Fuel and its vapors are extremely

flammable and explosive. Always handle

fuel with extreme care.

Failure to observe these safety instructions

can cause a fire or explosion which will

result in severe burns or death.

Not for

Reproduction

6

When Operating Equipment

• Do not tip the snowthrower at an angle which causes

the fuel to spill.

• Do not choke the carburetor to stop the engine.

• Never run the engine with the air cleaner assembly (if

equipped) or the air filter (if equipped) removed.

When Changing Oil

• If you drain the oil from the top oil fill tube, the fuel

tank must be empty or fuel can leak out and result in

a fire or explosion.

When Transporting Equipment

• Transport with fuel tank EMPTY, or with fuel shut-off

valve OFF.

When Storing Gasoline or Equipment With Fuel in

Tank

• Store away from furnaces, stoves, water heaters, or

other appliances that have pilot light or other ignition

source because they can ignite fuel vapors.

Running the engine produces heat.

Engine parts, especially muffler, become

extremely hot.

Failure to observe these safety

instructions could result in severe thermal

burns on contact.

• Never touch a hot engine or muffler. Allow muffler,

engine cylinder, and fins to cool before touching.

• Remove debris from muffler area and cylinder

area.

• Install and maintain in working order a spark

arrester before using equipment on forest-

covered, grass-covered, or brush-covered

unimproved land.

• It is a violation of California Public Resource Code,

Section 4442, to use or operate the engine on any

forest-covered, brush-covered, or grass-covered

land unless the exhaust system is equipped with

a spark arrester, as defined in Section 4442,

maintained in effective working order. Other states

or federal jurisdictions may have similar laws.

Contact the original equipment manufacturer,

retailer, or dealer to obtain a spark arrester

designed for the exhaust system installed on this

engine.

WARNING

• Disengage all clutches and shift into neutral before

starting the engine.

• Let the engine adjust to outdoor temperatures

before starting to clear snow.

• Use a grounded three-wire plug for all

snowthrowers equipped with electric drive motors

or electric starting motors.

Safe operation of the snowthrower

requires the proper care and maintenance

of the engine.

WARNING

• If there is natural or LP gas leakage in area, do not

start engine.

• Do not use pressurized starting fluids because

vapors are flammable.

Starting engine creates sparking.

Sparking can ignite nearby flammable

gases.

Explosion and fire could result.

WARNING

• When performing any maintenance or repairs on

the snowthrower, shut OFF the engine, disconnect

spark plug wire, and keep the wire away from the

plug to prevent someone from accidently starting

the engine.

• Check shear bolts and other hardware at frequent

intervals for proper tightness.

• Keep nuts and bolts tight and keep snowthrower in

good condition.

• Never tamper with safety devices. Check their

proper operation regularly and make necessary

repairs if they are not functioning properly.

• Components are subject to wear, damage, and

deterioration. Frequently check components and

replace with recommended parts, when necessary.

This snowthrower must be properly

maintained to ensure safe operation

and performance. Failure to observe the

safety instructions in this manual could

result in death or serious injury.

Not for

Reproduction

7

English

en

WARNING

Rapid retraction of the starter cord (kick-

back) will pull your hand and arm toward

the engine faster than you can let go.

Broken bones, fractures, bruises, or

sprains could result.

When Starting the Engine

• Pull the starter cord slowly until resistance is felt

and then pull rapidly to avoid kickback.

WARNING

Damaged or ungrounded power cords

could cause electric shock.

Electric shock could cause severe burns

or death.

When Using the Electric Starter

• The power cord must be properly grounded at all

times.

• Use only a three-conductor power cord properly

grounded to the power source.

• If the extension cord is damaged, it must be re-

placed a qualied person to avoid a hazard.

• Check control operation frequently. Adjust and

service as required.

• Use only factory authorized replacement parts, or

like, parts when making repairs.

• Always comply with factory specifications on all

settings and adjustments.

• Use only factory authorized, or like, attachments and

accessories such as wheel weights, counterweights,

or cabs.

• Never attempt to make any adjustments while

the engine is running (except when specifically

recommended by the factory).

WARNING

This snowthrower is only as safe as the

operator. If it is misused, or not properly

maintained, it can be dangerous. Remem-

ber you are responsible for your safety

and those around you.

• Keep the area of operation clear of all persons,

particularly small children and pets.

• Thoroughly inspect the area where the snowthrower

will be used and remove all doormats, sleds, boards,

wires, and other foreign objects.

• Do not operate the snowthrower without wearing

adequate winter clothing.

• Wear footwear that will improve footing on slippery

surfaces.

• Use caution to avoid slipping or falling especially when

operating the snowthrower in reverse.

• Never operate the snowthrower without good visibility

or light. Always be sure of your footing, and keep a

firm hold on the handles.

• Do not clear snow across the face of slopes. Use

extreme caution when changing direction on slopes.

Do not attempt to clear steep slopes.

• Do not overload the machine capacity by attempting to

clear snow too quickly.

• Never operate the snowthrower at high transport

speeds on slippery surfaces. Look behind the

snowthrower and use care when operating in reverse.

• Do not use the snowthrower on surfaces above ground

level such as roofs of residences, garages, porches, or

other such structures or buildings.

• Operators should evaluate their ability to operate the

snowthrower safely enough to protect themselves and

others from injury.

• The snowthrower is intended to remove snow only. Do

not use the snowthrower for any other purpose.

• Do not carry passengers.

• After striking a foreign object, shut OFF the engine,

disconnect the cord on electric motors, thoroughly

inspect the snowthrower for any damage, and repair

the damage before restarting and operating the

snowthrower.

• If the snowthrower vibrates abnormally, shut OFF the

engine. Vibration is generally a warning of trouble. See

an authorized dealer if necessary for repairs.

• For models equipped with electric starting motors,

disconnect the power cord after the engine starts.

Not for

Reproduction

8

2

SAFETY DECALS

Before operating the snowthrower, read and understand

the installed safety decals. The cautions and warnings are

provided to help you avoid personal injury or damage to your

snowthrower.

Thrown Ob-

jects Hazard

• Never direct

discharge chute

towards persons or

property.

Danger objets

projetés

• Ne jamais diriger la

chute en direction

des personnes ou

biens matériels.

Read the operator’s

manual for operat-

ing and safety

instructions.

Lire les consignes de

sécurité et

d’utilisation dans le

manuel d’utilisation.

Shut o engine and

remove key before

performing

maintenance or

repair work.

Arrêter le moteur et

retirer la clé avant

d’eectuer tout

entretien ou toute

réparation.

Amputation

Hazard

• Contact with auger

will cause serious

injury.

• Keep hands, feet

and clothing away.

• Keep bystanders

away.

Risque

d’amputation

• Tout contact avec la

tariére provoquera

de graves blessures.

• Tenir vos pieds, vos

mains et vêtements

á distance.

• Tenir les specta-

teurs á distance.

A

B

C

If any safety decals become damaged or illegible, order

replacements from your local authorized service dealer.

A — Part No. 1737865 Chute Danger Decal

B — Part No. 1739966 Auger Danger Decal

C — Part No. 279655 Engine Warning Decal

Not for

Reproduction

9

English

en

SAFETY SYSTEM TESTS

1. Start the snowthrower and engage the auger control

for several seconds.

2. Release the auger control.

3. The auger must stop within 5 seconds after the auger

control is released. If it does not:

a. Adjust the control cable.

b. If the auger still does not stop within 5 seconds,

see an Authorized Dealer.

DANGER

• Read and observe all the safety instructions in this

manual. Failure to do so will result in death or serious

injury.

• Never clear or unclog the discharge chute with

your hands. Fingers can quickly become caught and

traumatic amputation or severe laceration will result.

• Always use a clean-out tool to clear or unclog the dis-

charge chute.

This snowthrower is capable of

amputating hands and feet, and throwing

objects. Hand contact with the rotating

auger inside the discharge chute is the

most common cause of injury associated

with snowthrowers.

Not for

Reproduction

10

FEATURES AND CONTROLS

Snowthrower and Engine Controls

A — Auger Control

B — Chute Control - Chute Mount

C — Deector Control - Trigger

D — Starter Button

E — Starter Receptacle

F — Choke Control

G — Fuel Tank and Cap

H — Oil Fill/Dipstick

I — Primer Button

J — ON/OFF or Push/Pull Key

K — Starter Cord Handle

L — Oil Drain Plug

E

D

I

G

F

H

J

L

C

1739977

B

A

K

Control Symbols and Meanings

On / O switch

Choke closed; choke open

Push primer 2 times

Plug in extension cord

Press button to start

Engage auger control

Rotate chute control

3

Not for

Reproduction

11

English

en

Oil Recommendations

NOTICE: The engine was shipped from the factory without

oil. Before you start the engine, ensure that you add oil

according to the instructions in this manual. If you start the

engine without oil, it will be damaged beyond repair and will

not be covered under the warranty.

Use a high quality detergent oil classified for Service

SG, SH, SJ, SL, or higher. Synthetic 5W30 motor oil is

acceptable for all temperatures. DO NOT mix oil with

gasoline. See chart below for oil recommendations.

* Below 40°F (4°C) the use of SAE 30 will result in hard starting.

** Above 80°F (27°C) the use of 10W-30 may cause increased oil con-

sumption. Check oil level more frequently.

Add Oil / Check Oil Level

1. Ensure the snowthrower is level.

2. Clean the oil dipstick area of any debris.

3. See Specications for the oil capacity.

4. Remove the oil dipstick (A, Figure 4) and wipe it with a

clean cloth.

5. Add oil slowly into the engine oil ll (B).

6. Wait one minute and then insert the oil dipstick and turn

it clockwise to tighten.

7. Remove the oil dipstick and check the oil level.

8. If necessary, add oil until the level reaches the full mark

(C) on the oil dipstick. Do not overll.

9. Insert and tighten the oil dipstick securely.

OPERATION

B

A

C

D

4

Fuel Recommendations

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane / 87 AKI (91 RON). For high

altitude use, see below.

• Gasoline with up to 10% ethanol (gasohol) is

acceptable.

NOTICE: Do not use unapproved gasolines, such as E15

and E85. Do not mix oil in gasoline or modify the engine to

run on alternate fuels. Use of unapproved fuels will cause

damage to engine components, which will not be covered

under warranty.

To protect the fuel system from gum formation, mix a fuel

stabilizer into the fuel. See Storage. All fuel is not the

same. If starting or performance problems occur, change

fuel providers or change brands. This engine is certified to

operate on gasoline. The emissions control system for this

engine is EM (Engine Modifications).

Not for

Reproduction

12

1. Clean the fuel cap area of dirt and debris. Remove the

fuel cap (G, Figure 3).

2. Fill the fuel tank with fuel. To allow for expansion of the

fuel, do not ll above the bottom of the fuel tank neck.

3. Install the fuel cap.

Add Fuel

WARNING

When Adding Fuel

• Turn off engine and let cool at least 2 minutes

before removing the fuel cap and adding fuel.

• Fill fuel tank outdoors or in a well ventilated area.

• Do not overfill the fuel tank. To allow for the

expansion of gasoline, do not fill above the bottom

of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot

lights, heat, and other ignition sources.

• If fuel spills, wait until it evaporates before starting

engine.

Fuel and its vapors are extremely

flammable and explosive. Always handle

fuel with extreme care.

Failure to observe these safety instructions

can cause a fire or explosion which will

result in severe burns or death.

Start the Engine

WARNING

When Starting Engine

• Ensure that spark plug, muffler, fuel cap, and air

cleaner (if equipped) are in place and secured.

• Do not crank the engine with the spark plug

removed.

• If fuel is spilled, do not attempt to start the engine,

but move the snowthrower away from the area of

the spill, and avoid creating any source of ignition,

until the fuel vapors have dissipated.

• Do not over-prime the engine. Follow the engine

starting instructions in this manual.

• If the engine floods, set choke (if equipped) to

OPEN/RUN position, move throttle (if equipped) to

FAST position and crank until engine starts.

Fuel and its vapors are extremely

flammable and explosive. Always handle

fuel with extreme care.

Failure to observe these safety instructions

can cause a fire or explosion which will

result in severe burns or death.

NOTE: The electric starter is designed for a three-

conductor power cord only and operates on standard

household current. If a properly grounded electrical source

is not available, DO NOT use the electric starter. Contact

a licensed electrician for installation of a properly grounded

system.

WARNING

Damaged or ungrounded power cords

could cause electric shock.

Electric shock could cause severe burns

or death.

When Using the Electric Starter

• The power cord must be properly grounded at all

times.

• Use only a three-conductor power cord properly

grounded to the power source.

• If the extension cord is damaged, it must be re-

placed a qualied person to avoid a hazard.

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum

85 octane / 85 AKI (89 RON) gasoline is acceptable. For

carbureted engines, high altitude adjustment is required

to remain emissions compliant. Operation without this

adjustment will cause decreased performance, increased fuel

consumption, and increased emissions. Contact a Briggs &

Stratton Authorized Service Dealer for high altitude adjustment

information.

Operation of the engine at altitudes below 2,500 feet (762

meters) with the high altitude adjustment is not recommended.

For Electronic Fuel Injection (EFI) engines, no high altitude

adjustment is necessary.

Not for

Reproduction

13

English

en

1. Check the oil level. See Add Oil / Check Oil Level.

2. Ensure the auger control is disengaged.

3. Insert the ON/OFF key (A, Figure 5) and turn to the ON

position or insert the Push/Pull key, if equipped.

B

C

A

D

8. Electric start: Press the starter button (G). After the

engine starts, disconnect the power cord from the wall

receptacle rst and then from the starter receptacle.

NOTICE: To extend the life of the starter, use short

starting cycles (ve seconds maximum). Wait one min-

ute between starting cycles.

9. As the engine warms up, move the choke control (B,

Figure 5) to the open position.

NOTE: If the engine does not start after three attempts,

see Troubleshooting.

E

G

F

5

6

WARNING

Rapid retraction of the starter cord (kick-

back) will pull your hand and arm toward

the engine faster than you can let go.

Broken bones, fractures, bruises, or

sprains could result.

When Starting the Engine

• Pull the starter cord slowly until resistance is felt

and then pull rapidly to avoid kickback.

4. Turn the choke control (B) to the closed position.

NOTE: Do not close the choke control to start a warm

engine.

5. Press the primer button (C) two times.

NOTE: Do not press the primer button to start a warm

engine.

6. Rewind start: Firmly hold the starter cord (D). Pull the

starter cord slowly until resistance is felt, then pull rap-

idly.

7. Electric start: First connect the power cord (not sup-

plied) (E, Figure 6) to the starter receptacle (F) and then

into a wall receptacle. If an additional power cord is

required, ensure it is a three-conductor cord.

WARNING

• Do not choke the carburetor to stop the engine.

Gasoline and vapors are extremely

flammable and explosive.

Fire or explosion can cause severe burns

or death.

1. Turn the ON/OFF key (A, Figure 5) to the OFF position

or remove the Push/Pull key, if equipped.

2. Keep the key in a safe place out of the reach of children.

The engine cannot be started without the key.

Stop the Engine

Not for

Reproduction

14

Operate the Snowthrower

DANGER

• Read and observe all the safety instructions in this

manual. Failure to do so will result in death or serious

injury.

• Never clear or unclog the discharge chute with

your hands. Fingers can quickly become caught and

traumatic amputation or severe laceration will result.

• Always use a clean-out tool to clear or unclog the dis-

charge chute.

This snowthrower is capable of

amputating hands and feet, and throwing

objects. Hand contact with the rotating

auger inside the discharge chute is the

most common cause of injury associated

with snowthrowers.

WARNING

• Always be aware of the direction the snow is being

thrown. Nearby pedestrians, pets, or property may

be harmed by objects being thrown.

• Adjust the collector housing height to clear gravel or

crushed rock surface.

Ice, gravel, or other unintended objects

can be picked up by the auger and thrown

from the chute with force.

Objects thrown from the chute could cause

death, serious injury, or property damage.

WARNING

• Keep children out of the area during operation.

Children are often attracted to the equipment. Be

mindful of all persons present.

• Be alert and turn unit off if children enter the area.

Tragic accidents can occur if the operator

is not alert to the presence of children.

Children are often attracted to the unit and

the operating activity. Never assume the

children will remain where you last saw

them.

1. Start the engine and allow it to warm up several min-

utes. See Start the Engine.

2. Adjust the direction of the chute and the angle of the de-

ector to the desired positions. See Discharge Chute

and Deector.

3. Pull the auger control (A, Figure 7) against the handle to

engage the auger.

4. When clearing snow is completed, release the auger

control.

5. Allow the engine to run for one minute, then stop the en-

gine. See Stop the Engine.

B

A

7

C

Not for

Reproduction

15

English

en

Clearing a Clogged Discharge Chute

DANGER

Amputation hazard

The discharge chute contains a rotating impeller to

throw snow. Fingers can quickly become caught in

the impeller. Never clear or unclog the discharge

chute with your hands. Always use a clean-out tool.

Failure to observe these safety instructions will result

in traumatic amputation or severe laceration.

Hand contact with the rotating impeller inside the dis-

charge chute is the most common cause of injury associ-

ated with snowthrowers. Never use your hands to clean out

the discharge chute.

Discharge Chute and Deector

Chute Rotation - Chute Mount

1. Grasp the chute control handle at the base of the

chute (B, Figure 7).

2. Turn the handle left or right to rotate the chute. A

tension plate holds the chute in the desired position.

NOTICE: Do not use the chute control handle to lift the

snowthrower.

Deflector Adjustment

1. Squeeze and hold the button on the deflector control

handle (C, Figure 7).

2. Move the control handle up or down to adjust the snow

discharge height and distance.

3. Release the button to lock the deflector in the desired

position.

To safely clear a clogged discharge chute, follow

these instructions:

1. Shut OFF the engine.

2. Wait 10 seconds to be sure the impeller blades have

stopped rotating.

3. Always use a clean-out tool, not your hands.

Not for

Reproduction

16

MAINTENANCE

Change Oil

Used oil is a hazardous waste product and must be

disposed of properly. Do not discard with household

waste. Check with your local authorities, service center, or

dealer for safe disposal or recycling facilities.

Remove Oil

1. With engine o but still warm, remove the key and then

disconnect the sparkplug wire (A, Figure 8) and secure

it away from the sparkplug.

NOTE: To access the sparkplug wire, you must remove

the snow hood from the engine. See Access the

Sparkplug.

2. Remove the oil drain plug (B, Figure 9) and tilt the

snowthrower slightly to drain the oil into an appropriate

container.

3. After the oil has drained, install and tighten the oil drain

plug.

Maintenance Schedule

A

B

Emissions Control Service

Maintenance, replacement, or repair of the emissions

control devices and systems may be performed by any

non-road engine repair establishment or individual.

However, to obtain “no charge” emissions control service,

the work must be performed by a factory authorized dealer.

8

9

* Not required unless problems are noted with engine

performance. See an authorized service dealer for this item.

First 5 Hours

Change oil

Before Each Use

Check engine oil level

Perform the auger safety test

After Each Use

Remove accumulated snow and slush to prevent freezing

of the controls, wheels, discharge chute, and auger

Every 25 Hours or Annually

Check snowthrower for loose hardware

Check auger control cable adjustment

Check rubber auger for wear; replace if necessary

Every 50 Hours or Annually

Change engine oil

Check condition of muffler and muffler guard

Annually

Replace sparkplug

Check valve clearance *

Not for

Reproduction

17

English

en

Add Oil

1. Ensure the snowthrower is level.

2. Clean the oil dipstick area of any debris.

3. See Specications for the oil capacity.

4. Remove the oil dipstick (A, Figure 4) and wipe it with a

clean cloth.

5. Add oil slowly into the engine oil ll (B).

6. Wait one minute and then insert the oil dipstick and turn

it clockwise to tighten.

7. Remove the oil dipstick and check the oil level.

8. If necessary, add oil until the level reaches the full mark

(C) on the oil dipstick. Do not overll.

9. Insert and tighten the oil dipstick securely.

A

B

C

Control Cable Adjustment

WARNING

The auger must stop within 5 seconds after the auger

control is released. If it does not, adjust the control cable.

See Adjustment below or contact an authorized service

dealer to adjust the control cable.

Inspection

The auger should rotate only when the auger control is

engaged and must stop within 5 seconds when the auger

control is released. If the auger does not rotate or does not

stop as described, adjust the control cable or contact an

authorized service dealer to adjust the control cable.

If the drive belt has broken, contact an authorized service

dealer to replace the belt and adjust the control cable.

Adjustment

1. Stop the engine and remove the key. See Stop the En-

gine.

2. Lift the cable cover (A, Figure 10) to expose the adjust-

ment loops (B) and the cable end tting (C).

3. Remove the end tting from the adjustment loop and

reinstall as follows:

• If the auger rotates while the auger control is not

engaged, lengthen the control cable by installing

the end fitting in the next lowest loop (decrease

belt tension).

• If the auger does not rotate when the auger control

is engaged, shorten the control cable by installing

the end fitting in the next highest loop (increase

belt tension).

NOTE: Some slack must remain in the cable when the

auger control is not engaged.

4. Lower the cable cover into place.

5. Repeat the inspection procedure above. If the auger

does not rotate or does not stop as described, contact

an authorized service dealer to have the snowthrower

inspected.

10

Access the Sparkplug

To access the sparkplug, the snow hood must be removed

as follows:

1. Turn the ON/OFF key (A, Figure 11) to the OFF position

or remove the Push/Pull key, if equipped.

2. Grasp the choke control knob (B) and pull up to remove

it.

3. Remove the mounting screws or knobs (C) on the snow

hood.

4. Lift the snow hood (D) o the base and tilt it forward. Do

not disconnect the primer hose (E) or the keyswitch wire

(F).

Not for

Reproduction

18

5. Disconnect the sparkplug wire, then remove the spark-

plug (G) to clean or replace it. See Specications.

6. After installing the sparkplug, connect the sparkplug

wire.

7. Ensure that the primer hose and keyswitch wire are

properly connected, then t the snow hood into the base

and secure with the mounting screws or knobs.

8. Align the slots in the choke control knob with the tabs on

the choke shaft and push down to install. If the knob is

not properly installed, the choke control will not operate.

A

C

E

B

D

F

G

11

Auger and Scraper Bar Maintenance

Before each use, check wear limit on rubber auger and gap

between scraper bar support and ground (A, Figure 12).

• If wear limit on the rubber auger is reached, the two

rubber flights need replacing. See authorized dealer.

• If scraper bar support makes contact with the ground,

the scraper bar needs replacing. See authorized dealer.

12

Not for

Reproduction

19

English

en

WARNING

Fuel and its vapors are extremely flammable and explos-

sive. Always handle fuel with extreme care.

Failure to observe these safety instructions can cause a

fire or explosion which will result in severe burns or death.

When Storing Gasoline or Equipment With Fuel in

Tank

• Store away from furnaces, stoves, water heaters,

or other appliances that have pilot light or other

ignition source because they can ignite fuel vapors.

Storage

Engine Oil

While the engine is still warm, change the engine oil. See

Maintenance.

Before Placing in Storage

1. Thoroughly clean the snowthrower.

2. Remove the sparkplug. Clean and re-gap, if necessary,

or replace the sparkplug.

3. Make sure all nuts, bolts, and screws are securely fas-

tened.

4. Inspect moving parts for wear or damage. Replace

parts as necessary.

5. Lubricate the controls and moving parts.

6. Spray unpainted metal surfaces with a rust preventative.

7. Fold down the upper handle, if desired.

8. For indoor storage, cover the snowthrower and store it

in a dry area away from furnaces, stoves, water heaters,

or other appliances that have pilot lights or other ignition

sources.

9. For outdoor storage, raise the snowthrower o the

ground and cover it with a heavy tarpaulin.

After Removing from Storage

1. Raise the upper handle and tighten the handle knobs

securely.

2. Remove the oil dipstick and check the oil level. If nec-

essary, add oil until the level reaches the FULL mark on

the oil dipstick. Do not overll.

3. Fill the fuel tank with fresh fuel.

4. Ensure that all guards, shields, and covers are in place

and that all fasteners are tight.

Fuel System

Fuel can become stale when stored over 30 days. Stale fuel

causes acid and gum deposits to form in the fuel system

or on essential carburetor parts. To keep fuel fresh, use

Briggs & Stratton® Advanced Formula Fuel Treatment

& Stabilizer, available wherever Briggs & Stratton genuine

service parts are sold.

There is no need to drain gasoline from the engine if a fuel

stabilizer is added according to instructions. Run the engine

for 2 minutes to circulate the stabilizer throughout the fuel

system before storage. If gasoline in the engine has not

been treated with a fuel stabilizer, it must be drained into an

approved container. Run the engine until it stops from lack

of fuel. The use of a fuel stabilizer in the storage container is

recommended to maintain freshness.

Not for

Reproduction

20

TROUBLESHOOTING

Troubleshooting Chart

Problem Cause Solution

Auger does not stop

when auger control is

released

Control cable requires

adjustment

Adjust the control cable. See Maintenance section or contact an

authorized service dealer to adjust the cable.

Auger does not turn

when auger control is

engaged

Control cable requires

adjustment

Adjust the control cable. See Maintenance section or contact an

authorized service dealer to adjust the cable.

Chute rotation or

deector adjustment

does not work

Fasteners are too tight;

handle mount control

damaged

Contact an authorized service dealer.

Chute or deflector is frozen Clear snow or ice from chute and deflector parts; place

snowthrower in a heated area until snow or ice melts.

Engine does not start Key is off or not inserted Turn key to the ON position or insert Push/Pull key.

Primer not pressed Press primer button twice before pulling starter rope.

Out of fuel Fill fuel tank with fresh fuel.

Choke open - cold engine Turn choke to closed position before pulling starter rope.

Engine flooded Turn choke to open position; pull starter rope several times until

engine starts.

No spark Connect sparkplug wire; replace sparkplug.

Water in fuel or old fuel Drain fuel tank; fill fuel tank with fresh fuel.

Cord not plugged in or

circuit breaker tripped

(electric start models)

Plug in cord or replace defective cord; reset circuit breaker.

Engine is hard to start

or runs poorly

Incorrect oil Change oil to lighter viscosity (such as 5W-30).

Sparkplug fouled, worn, or

gapped incorrectly

Clean and re-gap sparkplug; replace sparkplug. Contact an

authorized service dealer.

Choke control set

incorrectly

Open choke control gradually as engine warms up.

Excessive vibration Loose parts or damaged

parts

Stop snowthrower immediately. Contact an authorized service

dealer.

Scraper bar does not

clean hard surface

Scraper bar worn Contact an authorized service dealer.

Snowthrower does not

discharge snow

Control cable requires

adjustment

Adjust the control cable. See Maintenance section or contact an

authorized service dealer to adjust the cable.

Drive belt worn or broken See authorized dealer to replace the belt.

Discharge chute clogged

with snow

STOP THE ENGINE! Ensure that the auger has stopped rotating.

Use a clean-out tool to remove snow from the discharge chute.

Never clear a clogged discharge chute with your hands! Refer to

“Warnings” in Operator Safety section.

Snowthrower does not

self-propel

Rubber auger is worn or

damaged

Contact an authorized service dealer.

Perform the inspection or repair as indicated in the Troubleshooting Chart.

La page charge ...

Simplicity SNOWTHROWER, SINGLE STAGE, STANDARD, SEARS CRAFTSMAN 7.5/22 (C950-52482-0) Manuel utilisateur

Ce manuel convient également à

Simplicity SNOWTHROWER, SINGLE STAGE, STANDARD, SEARS CRAFTSMAN 7.5/22 (C950-52482-0) Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents