KitchenAid KFIS29BBBL00 Manuel utilisateur

Catégorie
Frigos
Taper
Manuel utilisateur

Ce manuel convient également à

®
FRENCH DOOR BOTTOM MOUNT
REFRIGERATOR
DE
Congratulations on your purchase and welcome to the
KitchenAid Brand family of high-quality appliances.
Your new KitchenAid _French Door Refrigerator
combines advanced cooling technology with simple
operation and high efficiency.
REFRIGERATOR SAFETY ....................................................... 3
Proper Disposal of Your Old Refrigerator .............................. 3
PARTS AND FEATURES .......................................................... 4
What's New Behind the Doors? ............................................. 4
INSTALLATION INSTRUCTIONS ............................................ 5
Unpack the Refrigerator ......................................................... 5
Remove the Packaging ......................................................... 5
Clean Before Using ............................................................... 5
Location Requirements .......................................................... 5
Remove and Replace Refrigerator Doors .............................. 6
Remove Right-Hand Refrigerator Door ................................ 7
Remove Left-Hand Refrigerator Door .................................. 7
Replace Right-Hand Refrigerator Door ................................ 8
Replace Left-Hand Refrigerator Door................................... 8
- Final Steps ............................................................................ 8
Remove and Replace Freezer Drawer Front ......................... 9
Remove Drawer Front ........................................................... 9
Replace Drawer Front ........................................................... 9
- FinalSteps ............................................................................ 9
Electrical Requirements ....................................................... 10
Water Supply Requirements ................................................ 10
Connect the Water Supply ................................................... 10
Connect to Water Line ........................................................ 11
Connect to Refrigerator ...................................................... 11
Complete the Installation .................................................... 12
Handle Installation and Removal ......................................... 12
Install Handles ..................................................................... 12
Remove the Handles .......................................................... 13
Refrigerator Leveling, Door Closing and Alignment ............ 13
FILTERS AND ACCESSORIES .............................................. 15
Water Filtration System ........................................................ 15
- Install the Water Filter ......................................................... 15
The Water Filter Status Light .............................................. 15
Replace the Water Filter ..................................................... 16
Install Air Filter ...................................................................... 16
- Installing the Air Filter. ......................................................... 16
- Installing the Filter Status Indicator .................................... 16
Replacing the Air Filter. ....................................................... 17
Install Produce Preserver ..................................................... 17
- Installing the Produce Preserver ........................................ 17
- Installing the Status Indicator ............................................. 18
Replacing the Produce Preserver ....................................... 18
Accessories .......................................................................... 18
REFRIGERATOR USE ............................................................ 18
Opening and Closing Doors ................................................. 18
Using the Controls ............................................................... 19
Viewing and Adjusting Temperature Set Points ................. 19
Cooling On/Off .................................................................... 20
Options ................................................................................ 20
2
Each appliance that leaves our factory is inspected
thoroughly to ensure that it is working properly and is
in perfect condition.
Follow the Installation and Use and Care Instructions in
this guide and your refrigerator will provide many years
of reliable service.
- Additional Features ............................................................. 21
Water and Ice Dispensers .................................................... 22
Flush the Water System ...................................................... 22
The Water Dispenser. .......................................................... 22
The Ice Dispenser ............................................................... 23
The Dispenser Drip Tray ..................................................... 23
The Dispenser Light ............................................................ 23
The Dispenser Lock ............................................................ 23
Ice Maker and Ice Storage Bin ............................................. 24
Ice Production Rate ............................................................ 24
Style 1- Ice Maker in the Refrigerator ................................ 24
Style 2 - Ice Maker in the Freezer ....................................... 24
REFRIGERATOR FEATURES ................................................ 25
Refrigerator Shelves ............................................................. 25
Shelves and Sheff Frames .................................................. 25
Tuck Away Shell ................................................................. 25
Wine Rack ............................................................................. 25
Crisper and Crisper Cover .................................................... 26
Temperature-Controlled Drawer .......................................... 26
Preset Temperature Control ............................................... 26
Custom Temperature Control ............................................. 26
Drawer Removal and Replacement .................................... 26
Drawer Divider. .................................................................... 27
Meat Storage Guide ............................................................ 27
DOOR FEATURES .................................................................. 27
Door Bins .............................................................................. 27
FREEZER FEATURES ............................................................ 27
Pizza Pocket and Drawer Divider ......................................... 27
REFRIGERATOR CARE ......................................................... 28
Cleaning ................................................................................ 28
Exterior Cleaning ................................................................. 28
Interior Cleaning .................................................................. 28
Condenser Cleaning ........................................................... 29
Lights .................................................................................... 29
Vacation and Moving Care ................................................... 29
Vacations ............................................................................. 29
Moving ................................................................................. 29
TROUBLESHOOTING ............................................................ 30
Operation .............................................................................. 30
Noise ..................................................................................... 31
Temperature and Moisture ................................................... 32
Ice and Water ....................................................................... 33
Doors .................................................................................... 36
WATER FILTER CERTIFICATIONS ....................................... 37
PERFORMANCE DATA SHEET ............................................. 38
WARRANTY ............................................................................ 39
SERVICE NUMBERS .......................................... BACK COVER
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Disconnect power before servicing.
Replace all parts and panels before operating.
Remove doors from your old refrigerator.
Use nonflammable cleaner.
Keep flammable materials and vapors, such as gasoline,
away from refrigerator.
Use two or more people to move and install refrigerator.
[] Disconnect power before installing ice maker (on ice maker
kit ready models only).
Use a sturdy glass when dispensing ice (on some models).
Do not hit the refrigerator glass doors (on some models).
SAVE THESE INSTRUCTIONS
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.
Proper Disposal of Your Old Refi°igerator
Suffocation Hazard
Remove doors from your old refrigerator.
Failure to do so can result in death or brain damage.
IMPORTANT: Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are still dangerous
- even if they will sit for "just a few days." If you are getting rid of
your old refrigerator, please follow these instructions to help
prevent accidents.
Before You Throw Away Your Old Refrigerator or
Freezer:
Take off the doors.
Leave the shelves in place so that children may not easily
climb inside.
Important information to know about disposal of
refrigerants:
Dispose of refrigerator in accordance with Federal and Local
regulations. Refrigerants must be evacuated by a licensed,
EPA certified refrigerant technician in accordance with
established procedures.
A B C
D
E
F
A. Ice maker
B. Air filter
C. Water filter
D. Door bins
E.Crispers
F Pantry drawer
G. Freezer drawer
H. LED ramp-on lighting
I. In-Door-Ice ®ice
dispensing system
What's New Behind the Doors?
Your KitchenAid ®French Door Refrigerator comes equipped with various
innovative storage and energy efficient features.
Energy and Normal Operating Sounds
Your new French Door Bottom Mount refrigerator has been
designed to optimize energy efficiency, and better regulate
temperatures to match cooling demand. You may notice that it
operates differently than your previously owned refrigerator. It is
normal for the high-efficiency compressor to run for extended
periods of time at varying speeds in order to consume only the
energy necessary for optimum efficiency. In addition, during
various stages of the cooling cycle, you may hear normal
operating sounds that are unfamiliar to you.
More Storage Space
The French Door Bottom Mount has the most fresh food storage
space available, including a full-width, temperature controlled,
pantry drawer perfect for storing veggie trays or party platters.
In-Door-Ice _"_Ice Dispensing System
The ice storage bin located in the door provides an entire extra
shelf of storage space, and the storage bin is removable for easy
access to filtered ice.
Dual Evaporator (on some models)
The refrigerator compartment and freezer compartment have
separate evaporators to provide fresh food and frozen food with
separate climates. The refrigerator stays cool and humid for the
optimum storage of fresh foods while the freezer stays cold and
dry. Humidity from the refrigerator does not mix with dry freezer
air, so frost is controlled, which reduces freezer burn. Since no air
is shared between the refrigerator and freezer, the transfer of food
odors and tastes from the refrigerator to the freezer is eliminated.
Water Filter
NSF®Certified filter reduces chlorine taste and odor, particulates
(class I), lead, and mercury. Replacing the water filter every
6 months ensures clean, filtered drinking water.
Air Filter
An air filter is 15 times more powerful than baking soda at
reducing common food odors inside the refrigerator.
Produce Preserver (on some models)
Ethylene is a natural gas produced by fruits and vegetables to
promote ripening. The Produce Preserver absorbs ethylene, to
delay the over-ripening of fresh produce. As a result, certain
produce items will stay fresh longer.
Water Dispenser with Heasured Fill
The measured fill feature allows you to dispense the desired
amount of filtered water.
LED Lighting
The LEDlights do not ever need to be replaced.
Door Alarm
A helpful alarm sounds when the refrigerator door or freezer
drawer is left ajar.
Power Outage Indicator
If the power should go out while you are away from home, this
indicator will let you know that the refrigerator has been without
power.
Excessive Weight Hazard
Use two or more people to move and install
refrigerator.
Failure to do so can result in back or other injury.
......................................................................._j_j_j_j_j_jr___r_
Remove the Packaging
Remove tape and glue residue from surfaces before turning
on the refrigerator. Rub a small amount of liquid dish soap
over the adhesive with your fingers. Wipe with warm water
and dry.
Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your refrigerator. For
more information, see "Refrigerator Safety."
Dispose of/recycle all packaging materials.
When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the refrigerator for
cleaning or service, be sure to cover the floor with
cardboard or hardboard to avoid floor damage. Always pull
the refrigerator straight out when moving it. Do not wiggle or
"walk" the refrigerator when trying to move it, as floor
damage could occur.
iiiiiiiiiiiiiiiiiiiiiiiiiiii_,,,,i,j__r_j_1_____
Clean Before Using
After you remove all of the packaging materials, clean the inside
of your refrigerator before using it. See the cleaning instructions
in "Refrigerator Care."
important information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
Tempered glass is designed to shatter into many small,
pebble-size pieces. This is normal. Glass shelves and covers
are heavy. Use both hands when removing them to avoid
dropping.
Location Requ
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.
IMPORTANT: This refrigerator is designed for indoor, household
use only.
To ensure proper ventilation for your refrigerator, allow for a 1/2"
(1.25 cm) of space on each side and at the top. Allow for a 1"
(2.54 cm) space behind the refrigerator. If your refrigerator has an
ice maker, allow extra space at the back for the water line
connections. When installing your refrigerator next to a fixed wall,
leave a33/4"(9.5 cm) minimum space between the refrigerator
and wall to allow the door to swing open.
NOTE: This refrigerator is intended for use in a location where the
temperature ranges from a minimum of 55°F (13°C) to a
maximum of 110°F (43°C). The preferred room temperature range
for optimum performance, which reduces electricity usage and
provides superior cooling, is between 60°F (15°C) and 90°F
(32°C). It is recommended that you do not install the refrigerator
near a heat source, such as an oven or radiator.
/
i
1/2" (1.25 cm)
33/4" (9.5 cm)
Z
\
Remove and Replace Refrigerator Doors
NOTE: Measure the width of your door opening, to see whether or not you need to remove the refrigerator doors to move the
refrigerator into your home. If door removal is necessary, see the following instructions.
IMPORTANT: If the refrigerator was previously installed and you are moving it out of the home, before you begin, turn the refrigerator
control OFR Unplug the refrigerator or disconnect power. Remove food and adjustable door or utility bins from doors.
Gather the required tools and read all instructions before removing doors.
TOOLS NEEDED: 3Ae"hex key wrench and a #2 Phillips screwdriver
Electrical Shock Hazard
Disconnect power before removing doors.
Failure to do so can result in death or electrical shock.
Style 1 - Water Dispenser
Tubing Connection
\
\
\
\
\
\
\
A
A. Outer Ring
Wiring Plug
Top Left Hinge
A B
/ \
ii
V
C
A. _" InternalHex-HeadScrews
B. Ground Wire(Do NotRemove)
C. Do Not RemoveScrews
Style 2 - Water Dispenser
Tubing Connection
\
\
\
\
A
A. Outer Ring
A. _" Internal Hex-Head Screws
B. Hinge Cover Screw
C. Top Hinge Cover
D. Top Hinge
6
Remove Right-Hand Refrigerator Door
Electrical Shock Hazard
Disconnect power before removing doors.
Failure to do so can result in death or electrical shock.
1. Unplug refrigerator or disconnect power.
2. Keep the refrigerator doors closed until you are ready to lift
them free from the cabinet.
NOTE: Provide additional support for the refrigerator door
while the hinges are being removed. Do not depend on the
door gasket magnets to hold the door in place while you are
working.
3. Using a Phillips screwdriver, remove the cover from the Top
Hinge.
4. Using the 3/H' hex key wrench, remove the two internal hex
head screws from the top hinge, and set aside.
NOTE: Do not remove the two Iocator screws. These screws
will help you align the hinge when you replace the door.
L.
Remove Left-Hand Refrigerator Door
::::::::::::::::::::::_HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH_H_HHHHHHHHHHHHH_HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH_HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH_HHHHHHHHHHH_H_HHHHHHHHH_
IMPORTANT: The tubing and wiring for the water dispenser run
through the left-hand door hinge, so they must be disconnected
before removing the door.
1. Using a Phillips screwdriver, remove the cover from the top
B
hinge.
...........................................................'!
t
t
I
A. Tophingecover screw B. Top hinge cover
2=
Disconnect the water dispenser tubing located on top of the
door hinge.
Style 1 - Press the outer ring against the face of the fitting
and gently pull the dispenser tubing free.
NOTE: The water dispenser tubing remains attached to the
left-hand refrigerator door.
\
A. Top hinge cover screw
B. Top hinge cover
C. _" Internal hex head screws
D. Top hinge
Style 2 - Firmly pull up on the clasp. Then, pull the tubing out
of the fitting.
NOTE: The water dispenser tubing remains attached to the
left-hand refrigerator door.
5.
Excessive Weight Hazard
Use two or more people to lift the refrigerator door.
Failure to do so can result in back or other injury.
Lift the refrigerator door from the bottom hinge pin. The top
hinge will come away with the door.
\
3.
4.
Disconnect the wiring plug located on top of the door hinge.
Grasp each side of the wiring plug. With your left thumb,
press down to release the catch and pull the sections of
the plug apart.
NOTE: Do not remove the green, ground wire. It should
remain attached to the door hinge.
Using the 3/le"hex key wrench, remove the two internal hex
head screws from the top hinge, and set aside.
NOTES:
Provide additional support for the refrigerator door while
the hinges are being removed. Do not depend on the door
gasket magnets to hold the door in place while you are
working.
Do not remove the two Iocator screws. These screws will
help you align the hinge when you replace the door.
A B
Replace Right-Hand Refrigerator Door
1. Set the right-hand door onto the bottom hinge pin.
2. Insert the top hinge pin into the open hole in the top of the
refrigerator door.
3. Using the two 3/le"internal hex head screws, fasten the hinge
to the cabinet. Do not tighten the screws completely.
Replace Left-Hand Refrigerator Door
IMPORTANT: Do not intertwine the water tubing and wiring
bundles when reconnecting them.
1. Set the left-hand door onto the bottom hinge pin.
2. Using the two 3/le"internal hex head screws, fasten the hinge
to the cabinet. Do not tighten the screws completely.
3. Reconnect the water dispenser tubing.
Style 1 - Insert the tubing into the fitting until it stops and the
outer ring is touching the face of fitting.
Style 2 - Insert the tubing firmly into the fitting until it stops.
Close the clasp around the tubing. The clasp snaps into place
between the fitting and the collar.
4. Reconnect the electrical wiring.
Push together the two sections of the wiring plug.
Final Steps
1. Completely tighten the four internal hex head screws (two on
the right-hand door hinge and two on the left-hand door
hinge).
2. Replace both top hinge covers.
C
A. _" Internal hex head screws
B. Ground wire (do not remove)
5.
C.Locator screws (do not
remove)
Lift the refrigerator door from the bottom hinge pin. The top
hinge will come away with the door.
NOTE: It may not be necessary to remove the bottom hinges
and brake feet assemblies to move the refrigerator through a
doorway.
Only if necessary, use a driver with a #2 square bit tip to
remove the bottom hinges and a 3/8"nut driver to remove
the brake feet screws.
8
Remove and Replace Freezer Drawer Front
Depending on the width of your door opening, it may be
necessary to remove the freezer drawer front to move the
refrigerator into your home.
IMPORTANT:
If the refrigerator was previously installed and you are moving
it out of the home, before you begin, turn the refrigerator
control OFF, and unplug the refrigerator or disconnect power.
Remove food from the freezer drawer.
Two people may be required to remove and replace the
freezer drawer front.
Tool Needed: 1/4"hex driver
Remove Drawer Front
1. Open the freezer drawer to its full extension.
2. Remove the two screws at the top, inside the drawer front
(one on the left-hand side and one on the right-hand side)
that fasten the drawer front to the drawer glides.
3. Lift up on the drawer front to release the plastic studs from
the drawer glide bracket slots.
Replace Drawer Front
1. Pull out the freezer drawer glides to their full extension.
2. Holding the drawer front by its sides, align the two plastic
studs, located at the bottom, inside the drawer front, with the
drawer glide bracket slots.
NOTE: It helps if one person holds the drawer glides steady
while another person aligns the drawer front and inserts the
studs into the slots.
il.............
j,H .....
A "f"sJ_ i
B
A. Drawer front screw
B.Drawer front plastic stud
3. Replace and tighten the two screws at the top of the drawer
front (one on the left-hand side and one on the right-hand
side).
Final Steps
4.
A.Drawer glide bracket slots
Slide the drawer glides back into the freezer.
2.
3.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Plug into a grounded 3 prong outlet.
Reset the controls. See "Using the Control(s)."
Return all removable door parts to doors and the food to
refrigerator.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical
connection.
Recommended Grounding Method
A 115 volt, 60 Hz., AC only 15- or 20-amp fused, grounded
electrical supply is required. It is recommended that a separate
circuit serving only your refrigerator be provided. Use an outlet
that cannot be turned off by a switch. Do not use an
extension cord.
NOTE: Before performing any type of installation, cleaning, or
removing a light bulb, turn Cooling OFF, and then disconnect the
refrigerator from the electrical source. When you have finished,
reconnect the refrigerator to the electrical source and turn
Cooling ON. See "Using the Control(s)."
Water Supply Requirements
A cold water supply with water pressure between 35 and 120 psi
(241 and 827 kPa) is required to operate the water dispenser and
ice maker. If you have questions about your water pressure, call a
licensed, qualified plumber.
NOTE: If the water pressure is less than what is required, the flow
of water from the water dispenser could decrease or ice cubes
could be hollow or irregular shaped.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 35 and 120 psi (241 and
827 kPa).
If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).
Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.
Allow the storage tank on the reverse osmosis system to refill
after heavy use. The tank capacity could be too small to keep
up with the requirements of the refrigerator.
NOTE: Faucet mounted reverse osmosis systems are not
recommended.
If your refrigerator has a water filter, it may further reduce the
water pressure when used in conjunction with a reverse
osmosis system. Remove the water filter. See "Water
Filtration System."
If you have questions about your water pressure, call a licensed,
qualified plumber.
Connect the Water Supply
Read all directions before you begin.
IMPORTANT:
Plumbing shall be installed in accordance with the
International Plumbing Code and any local codes and
ordinances.
To avoid off-taste or odor in your ice or water, it is
recommended that you use copper tubing or Whirlpool
supply tubing, Part Number 8212547RP to connect the
household water line with the water line or water fitting
coming from the back of the refrigerator. Check for leaks.
Install tubing only in areas where temperatures will remain
above freezing.
TOOLS NEEDED:
Gather the required tools and parts before starting installation.
Flat-blade screwdriver
7/le"and 1/a"open-end wrenches or two adjustable wrenches
1/4"nut driver
NOTE: Do not use a piercing-type or 3/le"(4.76 mm) saddle valve
which reduces water flow and clogs easier.
10
Connect to Water Line
_HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH_HHHHHHHHHHHHHHHH_HHHHHHHHHHHHHHHHHHHHHHHH__HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH_
IMPORTANT: If you turn the refrigerator on before the water is
connected, turn the ice maker OFE
1. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.
3. Use a quarter-turn shutoff valve or the equivalent, served by a
1/2"household supply line.
NOTE: To allow sufficient water flow to the refrigerator, a
minimum 1/2"size household supply line is recommended.
4.
5.
6.
A
B
C
D
A. Sleeve
B. Nut
C. Copper tubing (to refrigerator)
D. Household supply line (_/2"minimum)
Now you are ready to connect the copper tubing to the
shutoff valve. Use 1/4"(6.35 mm) OD soft copper tubing to
connect the shutoff valve and the refrigerator.
Ensure that you have the proper length needed for the
job. Be sure both ends of the copper tubing are cut
square.
Slip compression sleeve and compression nut onto
copper tubing as shown. Insert end of tubing into outlet
end squarely as far as it will go. Screw compression nut
onto outlet end with adjustable wrench. Do not
overtighten.
A. Compression sleeve
B. Compression nut
C. Copper tubing
Place the free end of the tubing into a container or sink, and
turn on main water supply to flush out tubing until water is
clear. Turn off shutoff valve on the water pipe.
NOTE: Always drain the water line before making the final
connection to the inlet of the water valve, to avoid possible
water valve malfunction.
Bend the copper tubing to meet the water line inlet, which is
located on the back of the refrigerator cabinet as shown.
Leave a coil of copper tubing to allow the refrigerator to be
pulled out of the cabinet or away from the wall for service.
Style I
1. Remove plastic cap from water valve inlet port. Attach the
copper tube to the valve inlet using a compression nut and
sleeve as shown. Tighten the compression nut. Do not
overtighten. Confirm copper tubing is secure by pulling on
copper tubing.
2. Create a service loop with the copper tubing. Avoid kinks
when coiling the copper tubing. Secure copper tubing to
refrigerator cabinet with a "P" clamp.
B
u
D
3.
A. Copper tubing
B. "P" clamp
C. Compression nut
D. Compression sleeve
Turn on water supply to refrigerator and check for leaks.
Correct any leaks.
Style 2
1. Unplug refrigerator or disconnect power.
2. Remove and discard the short, black plastic part from the
end of the water line inlet.
3. Thread the nut onto the end of the tubing. Tighten the nut by
hand. Then tighten it with a wrench two more turns. Do not
overtighten.
NOTE: To avoid rattling, be sure the copper tubing does not
touch the cabinet's side wall or other parts inside the cabinet.
A B C D
A. Line to refrigerator
B. Nut (purchased)
C. Sleeve (purchased)
D. Supplied line from refrigerator
11
4. Install the water supply tube clamp around the water supply
line to reduce strain on the coupling.
5. Turn shutoff valve ON.
6. Check for leaks. Tighten any connections (including
connections at the valve) or nuts that leak.
7. On some models, the ice maker is equipped with a built-in
water strainer. If your water conditions require asecond water
strainer, install it in the 1/4"(6.35 mm) water line at either tube
connection. Obtain a water strainer from your appliance
dealer.
Complete the Installation
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
1. Plug into a grounded 3 prong outlet.
2. Flush the water system. See "Water and Ice Dispensers."
NOTE: Allow 24 hours to produce the first batch of ice. Discard
the first three batches of ice produced. Allow 3 days to
completely fill the ice storage bin.
Hand[÷ Installation and Removal
Parts Included: Refrigerator door handles (2), Freezer drawer
handle (1), %" hex key, spare setscrew(s)
Install Handles
NOTE: Handle mounting setscrews are preinstalled inside the
handle.
1. Remove the handles from the packaging inside the
refrigerator, and place them on a soft surface.
2. Open a refrigerator compartment door. On the closed door,
place a handle onto the shoulder screws so that the
setscrews are facing the adjacent door.
.4
I
A.Shoulder screws
B.Setscrews inside the handle
_B
3. Firmly push the handle toward the door until the handle base
is flush against the door.
4. While holding the handle, insert the short end of the hex key
into the upper hole and slightly rotate the hex key until it is
engaged in the setscrew.
iiii!i!!liii!iii
5=
6.
7.
Using a clockwise motion tighten the setscrew just until it
begins to contact the shoulder screw. Do not fully tighten.
Repeat steps 4 and 5 to fasten the lower setscrew.
Once both setscrews have been partially tightened as
instructed in the previous steps, fully tighten both setscrews.
IMPORTANT: When the screws feel tight, tighten them an
additional quarter-turn. The handle is not properly installed
without this extra tightening.
12
8. Repeat steps 2 through 7 to install the other handle onto the
adjacent refrigerator door.
9. With the freezer drawer closed, place the handle onto the
shoulder screws so that the setscrews are facing down
toward the floor.
A
A. Shoulder screw
B. Setscrews inside the handle
10. Firmly push the handle toward the drawer until the handle
base is flush against the drawer.
11. Insert the short end of the hex key into the left-hand hole and
slightly rotate the hex key until it is engaged in the setscrew.
12. Using a left to right motion tighten the setscrew a quarter-turn
at a time just until it begins to contact the shoulder screw. Do
not fully tighten.
13. Repeat steps 11 and 12 to fasten the right-hand setscrew to
the shoulder screw.
14. Once both setscrews have been partially tightened as
instructed in the previous steps, fully tighten both setscrews.
IMPORTANT: When the screws feel tight, tighten them an
additional quarter-turn. The handle is not properly installed
without this extra tightening.
15. Save the hex key and all instructions.
Remove the Handles
1. While holding the handle, insert the short end of the hex key
into a setscrew hole and slightly rotate the hex key until it is
engaged in the setscrew.
2. Using a right to left motion loosen the setscrew a quarter-turn
at a time.
3. Repeat steps 1 and 2 for the other setscrew. Slowly pull the
handle away from the door or drawer.
4. If necessary, use a Phillips screwdriver to remove the
shoulder screws from the door.
R÷frigerator L÷v÷ ing, Door C osin and A i nm÷nt
The base grille covers the adjustable brake feet and roller
assemblies located at the bottom of the refrigerator below the
freezer drawer. Before making any adjustments, remove the base
grille and move the refrigerator to its final location.
Tools Needed: 1/4"hex driver
Tools Provided: 1/8"hex key wrench
1. Remove the base grille. Grasp the grille firmly and pull it
toward you. Open the freezer drawer to access the brake
feet.
NOTE: To allow the refrigerator to roll easier, raise the break
feet by turning them counterclockwise. The front rollers will
be touching the floor.
l--
2,
3.
Move the refrigerator to its final location.
Lower the brake feet, by turning them clockwise, until the
rollers are off the floor and both brake feet are snug against
the floor. This keeps the refrigerator from rolling forward when
opening the refrigerator doors or freezer drawer.
13
4=
IMPORTANT: If you need to make further adjustments
involving the brake feet, you must turn both brake feet the
same amount to keep the refrigerator level.
Make sure the doors close easily. If you are satisfied with the
door opening and closing, skip the next section and go to
"Align the Doors." If however, the doors do not close easily or
the doors pop open, adjust the tilt.
To Adjust the Cabinet Tilt:
Open the freezer drawer. Use a 1/4"hex driver to turn both
brake feet clockwise the same amount. This will raise the
front of the refrigerator. It may take several turns to allow
the doors to close easier.
NOTE: Having someone push against the top of the
refrigerator takes some weight off the brake feet. This
makes it easier to turn them.
Style 1
_/4" O
A
B
A. Brake foot
B. Front roller
Style 2
\
|nn
A /
fl
A. Brake foot
5=
Make sure the doors are even at the top and that the space
between the bottom of the refrigerator doors and the top of
the freezer drawer is even. If necessary, align the doors.
To Align the Doors:
Keeping both refrigerator doors closed, pull out the
freezer drawer. Locate the bottom hinge pin of the
right-hand refrigerator door. The alignment screw is inside
the bottom hinge pin.
Insert the short end of the 1/8"hex key wrench (packed
with the Door Handle Installation Instructions) into the
bottom hinge pin until it is fully engaged in the alignment
screw.
To raise the refrigerator door, turn the hex key to the right.
To lower the door, turn the hex key to the left.
Continue to turn the alignment screw until the doors are
aligned.
6=
7=
A. Bottom hinge pin
B. _" Hex key wrench
Make sure the refrigerator is steady. If the refrigerator seems
unsteady or rolls forward when the door or drawer is pulled
open, adjust the brake feet.
To Steady the Refrigerator:
Open the freezer drawer. Using a 1/4"hex driver, turn both
brake feet clockwise the same amount until the brake feet
are snug against the floor. Check again. If not satisfied,
continue to adjust the brake feet by half turns of the
screw until the refrigerator does not roll forward when the
drawer is opened.
NOTE: Having someone push against the top of the
refrigerator takes some weight off the brake feet. This
makes it easier to turn the screws.
Replace the base grille by aligning the ends of the grille with
the leveling assemblies on each side and snapping the grille
into place.
14
Water Filtration $yste
Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain
filterable cysts.
Install the Water Filter
1. Locate the accessory packet in the refrigerator and remove
the water filter.
2. Take the water filter out of its packaging and remove the
cover from the O-rings. Be sure the O-rings are still in place
after the cover is removed.
A
3.
A. O-rings
The water filter compartment is located in the right-hand side
of the refrigerator ceiling. Push up on the compartment door
to release the catch, then lower the door.
4. Align the arrow on the water filter label with the cutout notch
in the filter housing and insert the filter into the housing.
5.
Turn the filter clockwise until it locks into the housing.
NOTE: If the filter is not correctly locked into the housing, the
water dispenser will not operate. Water will not flow from the
dispenser.
6.
7.
While the compartment door is still open, lift the filter up into
the compartment. Then, close the filter compartment door
completely.
Flush the water system. See "Flushing the Water Filter" in the
"Water and Ice Dispensers" section.
IMPORTANT: If you do not flush the water system, you may
experience dripping and/or decreased flow from the water
dispenser.
The Water Filter Status Light
Press OPTIONS on the control panel to launch the Options menu.
Press OPTIONS, under Filter Status, again to display the
percentage of filter life remaining (from 100% to 0%). Press ICE
MODE to return to the Normal screen.
The water filter status lights will help you know when to change
your water filter.
ORDER (yellow) - it is almost time to change the water filter.
While you are dispensing water, "Order Filter" will blink seven
times and sound an alert tone three times.
REPLACE (red) - Replace the water filter. While you are
dispensing water, "Replace Filter" will blink seven times and
an alert tone will sound three times.
RESET the water filter status tracking feature. After you
replace the disposable water filter with a new filter, closing
the filter compartment door will automatically reset the filter
status tracking feature. See "Using the Control(s)."
NOTE: "Replace Filter" will remain illuminated if a filter is not
installed or is installed incorrectly.
15
Replace the Water Filter
To purchase a replacement water filter, see "Accessories."
Replace the disposable water filter when indicated on the water
filter status display or at least every 6 months. If water flow to
your dispenser or ice maker decreases noticeably, change the
water filter sooner.
1. Locate the water filter compartment in the right-hand side of
the refrigerator ceiling. Push up to release and lower the
compartment door.
2. Turn the water filter counterclockwise (to the left), and pull it
straight out of the compartment.
NOTE: There may be some water in the filter. Some spilling
may occur. Use a towel to wipe up any spills.
3. Install the replacement water filter by following steps 2 - 7 in
the "Install the Water Filter" section.
Instal] Air FiEter (on some mo ÷ s)
An air filter is 15 times more powerful than baking soda at
reducing common food odors inside the refrigerator.
On some models, your refrigerator's accessory packet includes
an air filter, which must be installed prior to use.
Installing the Filter Status Indicator
:::::::::::::::::::::::: _::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::,_HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH_
The filter comes with a status indicator, which should be
activated and installed at the same time the air filter is installed.
Installing the Air Filter
Install the air filter behind the vented door, located on the rear
wall near the top of the refrigerator compartment.
1. Remove the air filter from its packaging.
2. Lift open the vented door.
3. Snap the filter into place.
A. Air filter
1.
2.
3=
Place the indicator face-down on a firm, flat surface.
Apply pressure to the bubble on the back of the indicator until
the bubble pops to activate the indicator.
Lift open the vented air filter door. On some models, there are
notches behind the door.
Models with notches:
With the indicator screen facing outward, slide the
indicator down into the notches.
NOTE: The indicator will not easily slide into the notches
if the bubble has not been popped.
B
A. Air filter status indicator
B. Notches
16
A ............................../ [
Close the air filter door, and check that the indicator is
i '"_
visible through the window in the door.
A. Status indicator window
Models without notches:
Place the indicator somewhere it is easily visible - either
inside the refrigerator, or elsewhere in your kitchen or
home.
Replacing the Air Filter
The disposable air filter should be replaced every 6 months,
when the status indicator has completely changed from white to
red.
To order a replacement air filter, contact us. See "Accessories"
for information on ordering.
1. Remove the used air filter by squeezing in on the side tabs.
2. Remove the used status indicator.
3. Install the new air filter and filter status indicator using the
instructions in the previous sections.
Install Produce Preserver (on some mode_s)
The produce preserver absorbs ethylene, to slow the ripening
process of many produce items. As a result, certain produce
items will stay fresh longer.
Ethylene production and sensitivity varies depending on the type
of fruit or vegetable. To preserve freshness, it is best to separate
produce with sensitivity to ethylene from fruits that produce
moderate to high amounts of ethylene.
Berries
Cantaloupe
Citrus Fruit
Lettuce
Low Low
Med. High
Med. Very Low
High Very Low
Installing the Produce Preserver
CAUTION: IRRITANT
MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES
FORM WHEN MIXED WITH OTHER PRODUCTS.
Do not mix with cleaning products containing ammonia,
bleach or acids. Do not get in eyes, on skin or clothing. Do
not breathe dust. Keep out of reach of children.
FIRST AID TREATMENT: Contains potassium
permanganate. If swallowed, call a Poison Control Center or
doctor immediately. Do not induce vomiting. If in eyes, rinse
with water for 15 minutes. If on skin, rinse with water.
1. Find the Produce Preserver housing inside the refrigerator.
2. Open the housing by pulling up and out on the back.
3. Remove the FreshFIow TM Produce Preserver pouches from
the packaging and place them into the housing.
NOTE: For best performance, always use two pouches.
4. Place the Produce Preserver housing onto the tab located on
the back wall of the crisper drawer.
17
Installing the Status Indicator
The produce preserver comes with a status indicator, which
should be activated and installed at the same time the pouches
are installed.
1. Place the indicator face-down on a firm, flat surface.
2. Apply pressure to the bubble on the back of the indicator until
the bubble pops, to activate the indicator.
3. Slide open the cap on the top of the produce preserver
housing.
4. Place the indicator in the top of the housing, facing outward.
5. Slide the cap closed, and check that the indicator is visible
through the rectangular hole in the cap.
NOTE: The cap will not easily close if the indicator's bubble
has not been popped.
Replacing the Produce Preserver
The disposable pouches should be replaced every 6 months or
when the status indicator changes completely from white to red.
To order replacements, contact us. See "Accessories" for
information on ordering.
1. Remove the used pouches from the produce preserver
housing.
2. Remove the used status indicator.
3. Install the replacement pouches and status indicator using
the instructions in the previous sections.
The following accessories are available for your refrigerator. To
order an accessory, contact us and ask for the part number.
In the U.S.A., visit our web site www.kitchenaid.com/
accessories or call 1-800-901-2042.
In Canada, visit our web site www.whirlpoolparts.ca
or call 1-800-807-6777.
affresh TMt Stainless Steel Cleaner:
In U.S.A., order Part #W10355016
In Canada, order Part #W10355016B
affresh TMtStainless Steel Wipes:
In U.S.A., order Part #W10355049
In Canada, order Part #W10355049B
affresh TMtKitchen & Appliance Cleaner:
In U.S.A., order Part #W10355010
In Canada, order Part #W10355010B
Water Filter:
Order Part #W10413645A or FILTER2
Air Filter:
Order Part #W10311524 or AIR1
Produce Preserver:
Order Part # W10346771A or FRESH1
Water Filter, Air Filter and Produce Preserver Bundle Pack:
Order Part # W10413643BL
1"TM AFFRESH is a trademark of Whirlpool, U.S.A.
Opening and C osi g Doors
There are two refrigerator compartment doors. The doors can be
opened and closed either separately or together.
There is a vertically-hinged seal on the left refrigerator door.
When the left side door is opened, the hinged seal
automatically folds inward so that it is out of the way.
When both doors are closed, the hinged seal automatically
forms a seal between the two doors.
A
A. Hinged seal
18
The controls are located above the external dispenser. Wait at least 24 hours between adjustments. Recheck the
temperatures before other adjustments are made.
IMPORTANT: The display screen on the dispenser control panel
will turn off automatically and enter "sleep" mode when the
control buttons and dispenser paddles have not been used for
2 minutes or more. Press any control button to reactivate the
display screen. The home screen will appear as shown.
View Temperature Set Points
1. Press and hold TEMPERATURE for 3 seconds to activate
Temperature mode.
2. When Temperature mode is activated, press TEMPERATURE
to toggle between the Refrigerator zone and the Freezer
zone. The display will show the temperature set point of the
selected compartment, as shown.
NOTE: When Temperature mode is activated, to view
temperatures in degrees Celsius, press the LIGHT button,
under Units. To return the display setting to Fahrenheit, press
the LIGHT button again.
Recommended Refrigerator Temperature
Recommended Freezer Temperature
Viewing and Adjusting Temperature Set Points
For your convenience, your refrigerator and freezer temperature
controls are set to the recommended set points at the factory.
When you first install your refrigerator, make sure the temperature
controls are still set to the recommended set points. The
recommended set points are 37°F (3°C) for the refrigerator and
0°F (-18°C) for the freezer.
IMPORTANT:
Wait 24 hours before you put food into the refrigerator. If you
add food before the refrigerator has cooled completely, your
food may spoil.
NOTE: Adjusting the set points to a colder than
recommended setting will not cool the compartments any
faster.
If the temperature is too warm or too cold in the refrigerator or
freezer, first check the air vents to be sure they are not
blocked before adjusting the controls.
The recommended set points should be correct for normal
household use. The controls are set correctly when milk or
juice is as cold as you like and when ice cream is firm.
NOTE: Areas such as a garage or porch, may experience
hotter or colder temperatures and higher humidity than inside
the home. You may need to adjust the temperature away from
the recommended set points to accommodate for these
conditions.
Adjust Temperature Set Points
Refrigerator set point range: 33°F to 45°F (0°C to 7°C).
Freezer set point range: -5°F to 5°F (-21 °C to -15°C).
1. Press and hold TEMPERATURE for 3 seconds to activate
Temperature mode.
2. When Temperature mode is activated, press TEMPERATURE
to select the Refrigerator zone. The display will show the
temperature set point of the selected compartment, as
shown.
3. Press LOCK, under plus, to raise the set point, or press
OPTIONS, under minus, to lower the set point.
4. When you have finished adjusting the refrigerator set point,
press TEMPERATURE to change the display to show the
freezer set point. When the zone has been changed,
"FREEZER" appears on the display screen.
19
5. Press LOCK, under plus, to raise the set point, or press
OPTIONS, under minus, to lower the set point.
Save/Confirm Temperature Settings
When you have finished adjusting both the refrigerator and
freezer set points, press MEASURED FILL "Confirm" to save
the settings.
NOTE: To exit Temperature mode without saving changes, press
the ICE MODE button under Back at any time, or allow about
60 seconds of inactivity. The temperature mode will turn off
automatically and return to the normal screen.
When adjusting temperature set points,
use the following chart as a guide:
REFRIGERATOR too cold
FREEZER too cold
REFRIGERATOR Setting
1° higher
FREEZER Setting
1° higher
Cooling On/Off
Your refrigerator and freezer will not cool when cooling is
turned off.
To turn cooling off, press and hold the LOCK and
MEASURED FILL buttons at the same time for 3 seconds.
When cooling is off, "Refrigeration Cooling is Off" will appear
on the display screen as shown.
IMPORTANT: To avoid unintentionally locking the dispenser
or changing other settings, be sure to press both buttons at
exactly the same time.
A. Press LOCK and MEASURED FILL at the same time.
To turn cooling back on, press and hold LOCK and
MEASURED FILL for 3 seconds again. "Cooling is Off" will
disappear from the display screen.
Options
Press the OPTIONS button to open the Options menu and select
between Max Cool, Max Ice and Water Filter Status.
Press the ICE MODE button at any time to return to the Normal
screen.
Max Cool
The Max Cool feature assists with periods of high refrigerator
use, full grocery loads, or temporarily warm room temperatures.
To turn on the Max Cool feature, press the OPTIONS button
to enter Options mode, then press the LOCK button, under
Max Cool, to activate the feature. When the feature is on, the
Max Cool icon will appear on the dispenser display screen.
The Max Cool feature will remain on for 24 hours unless
manually turned off.
(€
To manually turn off the Max Cool feature, press the
OPTIONS button to enter Options mode (unless you are
already in Options mode), then press LOCK again. When the
feature has been turned off, the Max Cool icon will disappear
from the dispenser display.
NOTE: Setting the freezer to a colder temperature may make
some foods, such as ice cream, harder.
Hax Ice
The Max Ice feature assists with temporary periods of heavy ice
use by increasing ice production.
To turn on the Max Ice feature, press the OPTIONS button to
enter Options mode, then press the TEMPERATURE button,
under Max Ice, to activate the feature. When the feature is on,
the Max Ice icon will appear on the dispenser display screen.
The Max Ice feature will remain on for 24 hours unless
manually turned off.
©
To manually turn off the Max Ice feature, press the OPTIONS
button to enter Options mode (unless you are already in
Options mode), then press TEMPERATURE again. When the
feature has been turned off, the Max Ice icon will disappear
from the dispenser display.
Water Filter Status
Press FILTER STATUS to display the percentage of use remaining
in the water filter (from 100% to 0%).
ALSO
The water filter status lights will let you know when to change
your water filter.
ORDER FILTER (Yellow) - Order a replacement water filter.
REPLACE FILTER (Red) - Replace the water filter. Replacing
the disposable water filter will automatically reset the water
filter status tracking feature. See "Water Filtration System."
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84

KitchenAid KFIS29BBBL00 Manuel utilisateur

Catégorie
Frigos
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues