Novamatic TW858E Manuel utilisateur

Catégorie
Sèche-linge
Taper
Manuel utilisateur
TW 858 E
User Manual
Notice d'utilisation
Tumble Dryer
Sèche-linge
CONTENTS
Safety information 2
Safety instructions 5
Product Description 7
Control Panel 8
Programme table 9
Options 10
Settings 12
Before first use 13
Daily use 15
Hints and tips 16
Care and cleaning 17
Troubleshooting 20
Technical data 22
Quick guide 24
Product Information sheet in reference
to E.U. regulation 1369/2017
26
Subject to change without notice.
VISIT OUR WEBSITE TO:
Get usage advice, brochures, trouble shooter, service and repair
information:
https://www.fust.ch/reparatur
SAFETY INFORMATION
Before beginning the installation and use of this appliance,
carefully read the supplied instructions. The manufacturer is
not responsible for any injuries or damage that are the result
of incorrect installation or usage. Always keep the
instructions in a safe and accessible location for future
reference.
- Read the supplied instructions.
Warning: Risk of fire / Flammable materials.
The appliance contains flammable gas, propane (R290), a
gas with a high level of environmental compatibility. Keep fire
and ignition sources away from the appliance. Be careful not
to cause damage to the refrigerant circuit containing
propane.
Children and vulnerable people safety
WARNING!
Risk of suffocation, injury or permanent disability.
This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
2
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
the use of the appliance in a safe way and understand the
hazards involved.
Children between 3 and 8 years of age and persons with
very extensive and complex disabilities shall be kept away
from the appliance unless continuously supervised.
Children of less than 3 years of age should be kept away
from the appliance unless continuously supervised.
Do not let children play with the appliance.
Keep all packaging away from children and dispose of it
appropriately.
Keep detergents away from children.
Keep children and pets away from the appliance when the
door is open.
If the appliance has a child safety device, it should be
activated.
Children shall not carry out cleaning and user maintenance
of the appliance without supervision.
General Safety
Do not change the specification of this appliance.
If the tumble dryer is put on top of a washing machine, use
the stacking kit. The stacking kit, available from your
authorized vendor, can be used only with the appliance
specified in the instructions supplied with the accessory.
Read it carefully before installation (refer to the Installation
leaflet).
The appliance can be installed as freestanding or below a
kitchen counter with correct space (refer to the Installation
leaflet).
Do not install the appliance behind a lockable door, a
sliding door or a door with a hinge on the opposite side,
that would prevent the appliance door from being fully
open.
The ventilation opening in the base must not be covered
by a carpet, mat, or any floor covering.
3
CAUTION: The appliance must not be supplied through an
external switching device, such as a timer, or connected to
a circuit that is regularly switched on and off by a utility.
Connect the mains plug to the mains socket only at the
end of the installation process. Make sure that the mains
plug is accessible after installation.
Ensure good air ventilation in the room where the
appliance is installed to avoid the backflow of unwanted
gases into the room from appliances burning gas or other
fuels, including open fires.
WARNING: Do not install the appliance in an environment
with no air exchange.
The appliance contains flammable gas, propane (R290), a
gas with a high level of environmental compatibility. Keep
fire and ignition sources away from the appliance. Be
careful not to cause damage to the refrigerant circuit
containing propane.
WARNING: In the appliance enclosure or in the built -in
structure, keep ventilation opening clear of obstruction.
WARNING: Do not damage the refrigerant circuit.
If the mains power supply cable is damaged, it must be
replaced by the manufacturer, its Authorised Service
Centre or similarly qualified persons to avoid an electrical
hazard.
Do not exceed the maximum load of 8 kg (refer to the
"Programme chart" chapter).
Do not use the appliance if items have been soiled with
industrial chemicals.
Wipe away lint or packaging debris that has accumulated
around the appliance.
Do not run the appliance without a filter. Clean the lint filter
before or after each use.
Do not dry unwashed items in the tumble dryer.
Items that have been soiled with substances such as
cooking oil, acetone, alcohol, petrol, kerosene, spot
removers, turpentine, waxes and wax removers should be
4
washed in hot water with an extra amount of detergent
before being dried in the tumble dryer.
Items such as foam rubber (latex foam), shower caps,
waterproof textiles, rubber backed articles and clothes or
pillows fitted with foam rubber pads should not be dried in
the tumble dryer.
Fabric softeners, or similar products, should only be used
as specified by the product manufacturer’s instructions.
Remove all objects from items that could be a source of
fire ignition such as lighters or matches.
WARNING: Never stop a tumble dryer before the end of
the drying cycle unless all items are quickly removed and
spread out so that the heat is dissipated.
Before any maintenance operation, deactivate the
appliance and disconnect the mains plug from the socket.
SAFETY INSTRUCTIONS
Installation
Warning: Risk of fire / Flammable
materials.
Remove all the packaging.
Do not install or use a damaged
appliance.
Follow the installation instructions
supplied with the appliance.
Do not install the appliance in an
environment with no air exchange
The appliance contains flammable gas,
propane (R290), a gas with a high level
of environmental compatibility. Keep
fire and ignition sources away from the
appliance. Be careful not to cause
damage to the refrigerant circuit
containing propane.
Always take care when moving the
appliance as it is heavy. Always use
safety gloves and enclosed footwear.
Do not install or use the appliance
where the temperature can be lower
than 5°C or higher than 35°C.
The floor area on which the appliance
is to be installed must be flat, stable,
heat resistant and clean.
Make sure that there is air circulation
between the appliance and the floor.
Always keep the appliance vertical
when it is being moved.
The rear surface of the appliance must
be put against a wall.
When the appliance is in its permanent
position, check if it is levelled correctly
with the aid of a spirit level. If it is not,
adjust the feet accordingly.
Electrical connection
WARNING! Risk of fire and
electric shock.
Connect the mains plug to the mains
socket only at the end of the
installation. Make sure that there is
access to the mains plug after the
installation.
The appliance must be earthed.
Make sure that the parameters on the
rating plate are compatible with the
5
electrical ratings of the mains power
supply.
Always use a correctly installed
shockproof socket.
Do not use multi-plug adapters and
extension cables.
Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
Do not touch the mains cable or the
mains plug with wet hands.
Use
WARNING! Risk of injury,
electric shock, fire, burns or
damage to the appliance.
Warning: Risk of fire / Flammable
materials. The appliance contains
flammable gas, propane (R290), a gas
with a high level of environmental
compatibility. Keep fire and ignition
sources away from the appliance. Be
careful not to cause damage to the
refrigerant circuit containing propane.
This appliance is for household
(indoors) use only.
Do not dry damaged (torn, frayed)
items that contain padding or fillings.
If laundry has been washed with a stain
remover, carry out an additional rinse
cycle before starting a drying cycle.
Dry only fabrics that are suitable to dry
in the appliance. Follow the cleaning
instruction on the item label.
Do not drink or prepare food with the
condensed water/distilled water. It can
cause health problems to people and
pets.
Do not sit or stand on the open door of
the appliance.
Do not dry dripping wet clothes in the
appliance.
Care and cleaning
WARNING! Risk of injury or
damage to the appliance.
Warning: Risk of fire / Flammable
materials. The appliance contains
flammable gas, propane (R290), a gas
with a high level of environmental
compatibility. Keep fire and ignition
sources away from the appliance. Be
careful not to cause damage to the
refrigerant circuit containing propane.
Do not use water spray and steam to
clean the appliance.
Clean the appliance with a moist soft
cloth. Use only neutral detergents. Do
not use abrasive products, abrasive
cleaning pads, solvents or metal
objects.
Be careful when you clean the
appliance to prevent damage to the
cooling system.
Compressor
WARNING! Risk of damage to
the appliance.
The compressor and its system in the
tumble dryer is filled with a special
agent which is free from fluoro-chloro-
hydrocarbons. This system must stay
tight. The damage of the system can
cause a leakage.
Service
To repair the appliance contact the
Authorised Service Centre.
Use original spare parts only.
Concerning the lamp(s) inside this
product and spare part lamps sold
separately: These lamps are intended
to withstand extreme physical
conditions in household appliances,
such as temperature, vibration,
humidity, or are intended to signal
information about the operational status
of the appliance. They are not intended
to be used in other applications and are
not suitable for household room
illumination.
6
Disposal
WARNING! Risk of injury or
suffocation.
Warning: Risk of fire / Risk of
material damage and damage to the
appliance.
Disconnect the appliance from the
mains electrical and water supplies.
Cut off the mains electrical cable close
to the appliance and dispose of it.
The appliance contains flammable gas
(R290). Contact your municipal
authority for information on how to
discard the appliance correctly.
Remove the door catch to prevent
children or pets from becoming trapped
in the drum.
Dispose of the appliance in accordance
with local requirements for the disposal
of Waste Electrical and Electronic
Equipment (WEEE).
PRODUCT DESCRIPTION
1 2
5
3
4
6
7
8
9
1
Water container
2
Control panel
3
Appliance door
4
Filter
5
Rating plate
6
Airflow slots
7
Heat Exchanger lid
8
Heat Exchanger cover
9
Adjustable feet
For ease of loading laundry or
ease of installation the door is
reversible. (see separate
leaflet).
7
CONTROL PANEL
1
89 7 6
3
5
4
2
1
Programme knob and RESET switch
2
Display
3
Trockenzeit (Time Dry) touch button
4
Start/Pause touch button
5
Zeitvorwahl (Delay Start) touch button
6
Knitterschutz (Extra Anticrease) touch
button
7
Reverse Plus touch button
8
Trockengrad (Dryness Level) touch
button
9
On/Off button
Press the touch buttons with
your finger in the area with the
symbol or name of the option.
Do not wear gloves when you
operate the control panel.
Make sure that the control
panel is always clean and dry.
Display
Symbol on the display Symbol description
time drying option on
delay start option on
indicator:
check Heat Exchanger
8
Symbol on the display Symbol description
indicator:
clean filter
indicator:
drain the water container
child lock on
wrong selection or knob is in the "Reset" position
programme duration
-
time Drying duration
-
delay start duration
PROGRAMME TABLE
Programme
Load
1)
Properties / Fabric type
2)
3)
Baumwolle (Cot‐
ton) Eco
8 kg
Cycle to be used to dry cotton with
"cotton cupboard" dryness level,
with maximum energy saving.
/
Baumwolle (Cotton) 8 kg
Cycle defined to dry cottons items
of different size / different weaving
altogether.
/
Pflegeleicht (Synthetics) 3,5 kg Synthetic and mixed fabrics.
/
Feinwäsche (Delicates) 4 kg
Delicate fabrics such as viscose,
rayon, acrylic, and their blends.
/
Wolle (Wool) 1 kg
Woollen fabrics. Gentle drying of washable wool‐
lens. Remove items immediately when the pro‐
gramme is completed.
Zeitprogramm (Time Dry‐
ing
5 kg
With this programme you can use
the Trockenzeit (Time Dry) option
and set the programme duration.
Drying time should be adequate to
the load, e.g. 2h for 5 kg of cotton.
/
Auffrischen (Refresh) 1kg Refreshing textiles that were in storage.
9
Programme
Load
1)
Properties / Fabric type
2)
Leichtbügeln (Easy Iron)
1 kg (or 5
shirts)
Easy care fabrics for which a mini‐
mum of ironing is necessary. The
drying results can be different from
one type of fabric to another.
Shake the items before putting
them in the appliance. When the
programme has ended, immediate‐
ly remove the items and put them
on a hanger.
/
Sportwäsche (Sports) 2 kg
Sportswear, thin and light fabrics,
microfiber, polyester.
/
Denim 4 kg
Leisure clothing such as jeans,
sweat-shirts of different material
thicknesses (e.g. at the neck, cuffs
and seams).
/
Bettwäsche (Bedlinen) 3kg
Bed linen such as single and dou‐
ble sheets, pillowcases, duvet cov‐
er.
/
Mix EasyDry (Mixed) 3kg
Cotton and synthetic fabrics. Low
temperature programme. Delicate
programme with warm air.
/
1)
The maximum weight refers to dry items.
2)
For fabric mark meaning see chapter HINTS AND TIPS: Preparing the laundry.
3)
The
Baumwolle (Cotton) Schranktrocken (Cupboard Dry) ECO programme is the “Standard cotton pro‐
gramme” according to Commission Regulation EU No. 392/2012. It is suitable for drying normal wet cotton laun‐
dry and it is the most efficient programme in terms of energy consumption for drying wet cotton laundry.
OPTIONS
Trockengrad (Dryness Level)
This function helps to increase dryness of
the laundry. There are 3 options:
Extratrocken (Extra Dry)
Schranktrocken (Cupboard Dry)
Bügeltrocken (Iron Dry)
Reverse Plus
Increase drum reversing frequency to
reduce items twisting and entanglement.
To increase uniformity of drying result and
help reduce creases. Recommended for
large or long items (e.g. sheets, trousers,
long dresses)"
Knitterschutz (Extra Anticrease)
Extends the anti-crease phase by 60
minutes at the end of the drying cycle.
This function reduces creases. The
laundry can be removed during the anti-
crease phase.
Trockenzeit (Time Dry)
You can set the programme duration, from
a minimum of 10 minutes to a maximum of
10
2 hours. The required duration is related
to the quantity of laundry in the appliance.
We recommend that you set a
short duration for small
quantities of laundry or for only
one item.
TIME DRYING RECOMMENDATION
10 - 20 min
action of cool
air only (no
heater).
20 - 40 min
additional dry‐
ing to improve
dryness after
previous dry‐
ing cycle.
TIME DRYING RECOMMENDATION
>40 min
full drying of
the small laun‐
dry loads up to
4 kg, well
spun (>1200
rpm).
Trockenzeit (Time Dry) on Wolle
(Wool) programme
Option suitable for Wolle (Wool)
programme to adjust final dryness level.
Options table
Programmes
1)
Trockengrad (Dry‐
ness Level)
Reverse
Plus
Knitter‐
schutz
(Extra An‐
ticrease)
Trocken‐
zeit (Time
Dry)
Baumwolle
(Cotton) Eco
Baumwolle (Cotton)
Pflegeleicht (Syn‐
thetics)
Feinwäsche (Deli‐
cates)
Wolle (Wool)
2)
Zeitprogramm (Time
Drying
Auffrischen (Re‐
fresh)
Leichtbügeln (Easy
Iron)
Sportwäsche
(Sports)
11
Programmes
1)
Trockengrad (Dry‐
ness Level)
Reverse
Plus
Knitter‐
schutz
(Extra An‐
ticrease)
Trocken‐
zeit (Time
Dry)
Denim
Bettwäsche (Bedli‐
nen)
Mix EasyDry
(Mixed)
1)
Together with the programme you can set 1 or more options. To activate or deactivate them, press the related
touch button.
2)
See chapter OPTIONS: Time Drying on Wool programme
SETTINGS
A B C
E
DF
A. Trockenzeit (Time Dry) touch button
B. Start/Pause touch button
C. Zeitvorwahl (Delay Start) touch button
D. Knitterschutz (Extra Anticrease) touch
button
E. Reverse Plus touch button
F. Trockengrad (Dryness Level) touch
button
Child lock function
This option prevents children playing with
the appliance while a programme is
operating. The touch buttons are locked.
Only the on/off button is unlocked.
Activating the child lock option:
1. Press the on/off button to activate the
appliance.
2. Press and hold touch button (D) for a
few seconds.
The child lock indicator comes on.
It is possible to deactivate the
child lock option while a
programme operates. Press
and hold the same touch
buttons until the child lock
indicator goes off. The Child
Lock function isn't available for
8 s after switching on the
appliance.
Adjustment of remaining
laundry moisture
Every time you enter in the
"Adjustment of remaining
laundry moisture" mode,
previously set degree of
remaining moisture will change
into next value ( e.g previously
set will change into
).
To change the default degree of remaining
moisture:
1. Press the on/off button to activate the
appliance.
2. Use the programme knob to set any
programme.
3. Wait approximately 8 seconds.
4. Press and hold buttons (F) and (E) at
the same time.
12
One of these indicators comes on:
the maximum dryness
the more dry laundry
the standard dry laundry
5. Press and hold buttons (F) and (E)
again until the indicator of the correct
level comes on.
If the display returns to the
normal mode (the time of
the selected programme
from step 2. will be
displayed), while setting the
degree of remaining
moisture, press and hold
buttons (F) and (E) once
again to enter to the
"Adjustment of remaining
laundry moisture" mode
(previously set degree of
remaining moisture will
change into next value).
6. After 5 s the display returns to normal
mode.
Water container indicator
By default, the water container indicator is
on. It comes on when the programme is
completed or when it is necessary to
empty the water container.
If a draining kit is installed
(additional accessory), the
appliance automatically drains
the water from the water
container. In this case we
recommend that you deactivate
the indicator of the water
container.
Deactivating the water container
indicator:
1. Press the on/off button to activate the
appliance.
2. Wait approximately 8 seconds.
3. Press and hold touch buttons (E) and
(D) at the same time.
The display shows one of these 2
configurations:
The display shows "Off". After 5 s
the display returns to normal mode.
The display shows "On". After 5 s
the display returns to normal mode.
Buzzer on/off
To deactivate or activate the acoustic
signals, press and hold for approximately
2 seconds touch buttons (A) and (C) at
the same time.
BEFORE FIRST USE
Rear drum locks are removed
automatically when dryer is
activated for the first time.
Possible to hear some noise.
It is highly recommended to
start any programme for the
first time without the load for
a few seconds to ensure that
the rear drum locks are
removed properly.
To unlock the rear drum locks:
1. Switch on the appliance.
2. Set any programme.
3. Press the Start/Pause button.
Drum starts to rotate. Rear drum locks are
automatically deactivated.
If the drum still does not rotate,
please release the rear drum
locks manually (to do that,
please use provided key).
A
B
13
A
B
Before you use the appliance to dry
items:
Clean the tumble dryer drum with a
moist cloth.
Start a 1 hour programme with moist
laundry.
At the beginning of the drying
cycle (first 3-5 min) there could
be a slightly higher sound level.
This is due to the compressor
starting up. This is normal for
compressor powered
appliances such as
refrigerators and freezers.
Unusual smell
The appliance is tightly packed.
After product unpacking you can feel an
unusual smell. This is normal for brand
new products.
Appliance is built of several different types
of material which all together can generate
unusual smell.
Over usage time, after few drying cycles
unusual smell gradually disappears.
Noises
Different noises may be heard
at different times during the
drying cycle. They are perfectly
normal operating sounds.
Working compressor.
Brrrr
Rotating drum.
Working fans.
Working pump and transferring
condensation to the tank.
14
DAILY USE
Start a programme without
delay start
1. Prepare the laundry and load the
appliance.
CAUTION! Make sure that
when you close the door,
the laundry does not get
caught between the
appliance door and the
rubber seal.
2. Press the on/off button to activate the
appliance.
3. Set the correct programme and
options for the type of load.
The display shows the programme
duration.
Real drying time will depend on
type of the load (quantity and
composition), the room
temperature and the humidity
of your laundry after spin drying
phase.
4. Press the Start/Pause touch button.
The programme starts.
Starting the programme with
delay start
1. Set the correct programme and
options for the type of load.
2. Press the delay start button again and
again until the display shows the delay
time you want to set.
You can delay the start of a
programme from a
minimum of 1 hour to a
maximum of 20 hours.
3. Press the Start/Pause touch button.
The display shows the countdown of the
delay start.
When the countdown is completed, the
programme starts.
Change a programme
1. Press the on/off button to deactivate
appliance
2. Press the on/off button to activate the
appliance.
3. Set the programme.
Alternatively:
1. Rotate the selector knob to the
"Reset" position.
2. Wait for 1 second. The display shows
.
3. Set the programme.
At the end of the programme
When the programme is completed:
An intermittent acoustic signal
operates.
The display shows
The indicators Wärmetauscher
(Condenser) and Sieb (Filter)
comes on.
The Start/Pause indicator is on.
The appliance continues to operate with
the anti-crease phase for approximately
30 minutes or more if Knitterschutz (Extra
Anticrease) option was set (see chapter
Option - Knitterschutz (Extra Anticrease)
).
The anti-crease phase reduces creasing.
You can remove the laundry before the
anti-crease phase is completed. We
recommend, for better results, that you
remove the laundry when the phase is
almost completed or completed.
When the anti-crease phase is completed:
The display still shows
15
The indicators Wärmetauscher
(Condenser) and Sieb (Filter)
comes on.
Start/Pause indicator goes off.
1. Press the on/off button to deactivate
the appliance.
2. Open the appliance door.
3. Remove the laundry.
4. Close the appliance door.
Possible causes of unsatisfactory drying
results:
Inadequate default dryness level
settings. See chapter
Adjustment of
default dryness level
Room temperature is too low or too
high. Optimal room temperature is
between 18°-25°C.
Always clean the filter and
empty the water container
when a programme is
completed.
Stand-by function
To reduce energy consumption, this
function automatically deactivates the
appliance:
After 5 minutes if you do not start the
programme.
After 5 minutes from the end of the
programme.
The time is reduced to 30
seconds if the selector knob is
pointing to "Reset" position.
HINTS AND TIPS
Preparing the laundry
Very often the clothes after
washing cycle are kneaded and
tangled altogether.
Drying kneaded and tangled
clothes is inefficient.
To assure proper air flow and
even drying it is recommended
to shake and load one by one
the clothes to the tumble dryer.
To assure proper drying process:
Close the zips.
Close the fasteners of duvet covers.
Do not dry ties or ribbons loose (e.g.
apron ribbons). Tie them before you
start a programme.
Remove all items from pockets.
Turn items with the internal layer made
of cotton inside out. Cotton layer must
be faced outwards.
Always set the programme suitable for
the type of laundry.
Do not put light and dark colours
together.
Use suitable programme for cottons,
jersey and knitwear to reduce
shrinkage.
Do not exceed the maximum load
stated in the programmes chapter or
shown on the display.
Dry only the laundry that is suitable for
tumble drying. Refer to the fabric label
on the items.
Do not dry large and small items
together. Small items can be trapped
inside the large items and remain wet.
Shake the large clothes, fabrics before
placing in the tumble dryer. It is to
avoid moist places inside the fabric
after the drying cycle.
Fabric label Description
Laundry is suitable for tumble drying.
Laundry is suitable for tumble drying at higher temperatures.
16
Fabric label Description
Laundry is suitable for tumble drying at low temperatures only.
Laundry is not suitable for tumble drying.
CARE AND CLEANING
Cleaning the filter
CAUTION! Avoid the use of
water to clean the filter. Instead
throw away lint in the dustbin
( avoid dispersion of plastic
fiber in water ambient).
To achieve the best drying
performances clean the filter
regularly , clogged filter lead to
longer cycles and energy
consumption increase.
Use your hand to clean the
filter , and if necessary , a
vacuum cleaner .
1. 2.
1
2
3.
1
2
4.
5.
1)
6.
2
1
1)
If necessary remove fluff from the filter socket and gasket. You can use a vacuum cleaner.
17
Emptying the water container
1. 2.
3. 4.
You can use the water from the
water container as an
alternative to distilled water
(e.g. for steam ironing). Before
you use the water, remove dirt
residues with a filter.
Cleaning the Heat Exchanger
1. 2.
1
2
3. 4.
11
22
18
5. 6.
7. 8.
9.
2
1
CAUTION! Do not touch the
metal surface with bare hands.
Risk of injury. Wear protective
gloves. Clean carefully to avoid
damaging the metal surface.
Cleaning the humidity sensor
CAUTION! Risk of humidity
sensor damage. Do not use
abrasive materials or steel wool
to clean the sensor.
To assure best drying results the
appliance is equipped with metal humidity
sensor. It is placed on the inner side of the
door area.
Over usage time the surface of the sensor
may get dirty what deteriorates the drying
performance.
We recommend to clean the sensor at
least 3 or 4 times or if you observe the
drop of drying performance.
To clean you can use harder side of dish-
washing sponge and bit of vinegar or dish
soap.
To clean the sensor:
1. Open the loading door.
2. Clean the surfaces of the humidity
sensor wiping off the metal surface
several times.
19
Cleaning the drum
WARNING! Disconnect the
appliance before you clean it.
Use a standard neutral soap detergent to
clean the inner surface of the drum and
drum lifters. Dry the cleaned surfaces with
a soft cloth.
CAUTION! Do not use
abrasive materials or steel wool
to clean the drum.
Cleaning the control panel and
housing
Use a standard neutral soap detergent to
clean the control panel and housing.
Use a moist cloth to clean. Dry the
cleaned surfaces with a soft cloth.
CAUTION! Do not use furniture
cleaning agents or cleaning
agents which can cause
corrosion.
Cleaning the airflow slots
Use a vacuum cleaner to remove fluff from
the airflow slots.
TROUBLESHOOTING
WARNING! Refer to Safety
chapters.
Error Codes
The appliance does not start or it stops during operation.
First try to find a solution to the problem (refer to the table). If the problem persists,
contact the Authorised Service Centre.
WARNING! Deactivate the appliance before carrying out any check.
In case of major problems, the acoustic signals operate, the display shows an
error code and the Start/Pause button may flash continuously:
Error code Possible cause Remedy
E5A
Appliance motor overloaded.
Too much laundry or entrap in the
drum.
The programme was not comple‐
ted. Remove the laundry from the
drum, set the programme and re‐
start the cycle.
E97
Internal fail. No communication be‐
tween electronic elements of the
appliance.
The programme was not finished
properly or the appliance stoped
too early. Switch the appliance off
and on again.
If the error code appears again,
contact the Authorised Service
Centre.
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60

Novamatic TW858E Manuel utilisateur

Catégorie
Sèche-linge
Taper
Manuel utilisateur

dans d''autres langues