Samsung SR1AM7040WG Manuel utilisateur

POWERbot

User manual

SR1AM70



, SR2AM70



Series

• Before operating this unit, please read the instructions carefully.

• For indoor use only.

1_VR7000_EN_DJ68-00763C-10_USA.indd 1 2017-12-01 오후 4:46:02

ENGLISH-02

Contents

03

Safety information

10

Installation

Accessories / Installation note

12

Charging

Automatic charging / Recharging / Low

battery (Lo)

14

Using POWERbot

Turning the power on/off / Selecting

cleaning modes/ Using special cleaning

functions/ About the boundary

markers/ Using Energy-saving mode

18

Using the remote control

21

Name of each part

Top / Bottom / Display panel

23

Setting time/schedule

Setting the time / Setting the schedule

26

Cleaning and maintaining

Cleaning the dustbin / Cleaning the sensors and

the camera / Cleaning the brush and Auto shutter

tool / Cleaning the Driving wheel

28

Samsung Connect App

32

Notes and cautions

Charging / Using / Cleaning and maintenance /

About the battery / About the IrDA sensor

34

Information codes

36

Troubleshooting

40

Open Source Announcement

41

Specications

1_VR7000_EN_DJ68-00763C-10_USA.indd 2 2017-12-01 오후 4:46:02

ENGLISH-03

Safety information

SAFETY INFORMATION

WARNING

• Before operating the appliance, please read this manual thoroughly and

retain it for your reference.

WARNING

• Because the following operating instructions cover various models, the

characteristics of your vacuum cleaner may differ slightly from those

described in this manual.

CAUTION/WARNING SYMBOLS USED

WARNING

Indicates that a danger of death or serious injury exists.

CAUTION

Indicates that a risk of personal injury or material damage exists.

OTHER SYMBOLS USED

NOTE

Indicates that the following text contains additional important

information.

State of California Proposition 65 Warning (US only)

WARNING

This product contains chemicals known to the State of California to cause

cancer and birth defects or other reproductive harm.

L i - i o n

For battery recycling go to call2recycle.org

or call 1-800-822-8837

1_VR7000_EN_DJ68-00763C-10_USA.indd 3 2017-12-01 오후 4:46:03

ENGLISH-04

Safety information

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should be observed, including

the following:

READ ALL INSTRUCTIONS BEFORE USING YOUR POWERbot.

Unplug from outlet when not in use and before conducting maintenance.

WARNING: To reduce the risk of re, electric shock, or injury:

GENERAL

• Use only as described in this manual.

• Do not operate POWERbot or the battery charger / docking station if it has been

damaged in any way.

• If the vacuum cleaner is not working as it should, has been dropped, damaged,

left outdoors, or dropped in water, contact an authorized Samsung service center.

• Do not handle the battery charger / docking station or POWERbot with wet hands.

• Use only on dry, indoor surfaces.

• This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety. Do not let children

clean or perform user maintenance on the POWERbot without adult supervision.

• Place the cords from other appliances out of the area to be cleaned.

• Do not operate the vacuum in a room where an infant or child is sleeping.

• Do not operate the vacuum in an area where there are lit candles or fragile

objects on the oor.

• Do not operate the vacuum in a room that has lit candles on furniture that the

vacuum may accidentally hit or bump into.

• Do not allow children to sit on the vacuum.

• Do not use the vacuum on a wet surface.

Battery charger / Docking station

• Do not modify the polarized plug to t a non-polarized outlet or extension cord.

• Do not use outdoors or on wet surfaces.

• Unplug the battery charger / docking station from the outlet when not in use

and before servicing.

• Use only the battery charger / docking station supplied by the manufacturer to

recharge the POWERbot.

• Do not use with a damaged cord or plug or a loose power outlet.

• Do not pull or carry by the cord, use the cord as a handle, close the door on the

cord, or pull the cord around sharp edges or corners. Keep the cord away from

heated surfaces.

1_VR7000_EN_DJ68-00763C-10_USA.indd 4 2017-12-01 오후 4:46:03

ENGLISH-05

• Do not use extension cords or outlets with inadequate current carrying capacity.

• Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.

• Do not mutilate or incinerate batteries as they will explode at high temperatures.

• Do not attempt to open the battery charger / docking station. Repairs should

only be carried out by a qualied Samsung service center.

• Do not expose the battery charger / docking station to high temperatures or

allow moisture or humidity of any kind to come into contact with the battery

charger / docking station.

POWERbot

• Do not use to pick up hard or sharp objects such as glass, nails, screws, coins,

and etc.

• Do not use without a lter in place. When servicing the unit, never put ngers or

other objects into the fan chamber in case the unit accidentally turns on.

• Do not put any objects into openings. Do not use with any openings blocked;

keep openings free of dust, lint, hair, and anything that may reduce air ow.

• Do not use to pick up toxic materials (chlorine bleach, ammonia, drain cleaner,

etc.).

• Do not use to pick up anything that is burning or smoking, such as cigarettes,

matches, or hot ashes.

• Do not use to pick up ammable or combustible liquids such as gasoline or use

in areas where they may be present. Also do not use in:

– Locations with candles or desk lamps on the oor.

– Locations with unattended res (re or embers).

– Locations with distilled alcohol, thinner, ashtrays with burning cigarettes, etc.

• Do not use POWERbot in an enclosed space lled with vapors given off by oil

based paint, paint thinner, moth proong substances, ammable dust, or other

explosive or toxic vapors.

• Leaks from battery cells can occur under extreme usage or temperature

conditions. If the liquid gets on skin, wash quickly with water. If the liquid

gets into eyes, ush them immediately with clean water for a minimum of

10minutes. Seek medical attention.

SAVE THESE INSTRUCTIONS

POLARIZED PLUG INSTRUCTIONS

• To reduce the risk of electric shock, this appliance has a polarized plug (one

blade is wider than the other). This plug will t in a polarized outlet only one

way. If the plug does not t fully in the outlet, reverse the plug. If it still does

not t, contact a qualied electrician to install a proper outlet. Do not modify the

plug in any way.

1_VR7000_EN_DJ68-00763C-10_USA.indd 5 2017-12-01 오후 4:46:03

ENGLISH-06

Safety information

REGULATORY NOTICE

1. FCC Notice

CAUTION

FCC CAUTION:

• Any changes or modications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

• This device complies with Part 15 of FCC Rules. Operation is Subject to following

two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received including interference that

cause undesired operation.

• For products available in the US and Canadian markets, only channels 1~11 are

available. You cannot select other channels.

FCC STATEMENT:

• This equipment has been tested and found to comply within the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation.

• This equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

– Reorienting or relocating the receiving antenna

– Increasing the separation between the equipment and receiver

– Connecting the equipment to an outlet that is on a different circuit from the

radio or TV.

– Consulting the dealer or an experienced radio/TV technician for help.

FCC RADIATION EXPOSURE STATEMENT:

• This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated so

there are at least 8 inches (20 cm) between the radiator and your body. This

device and its antenna(s) must not be co-located or operated in conjunction with

any other antenna or transmitter.

1_VR7000_EN_DJ68-00763C-10_USA.indd 6 2017-12-01 오후 4:46:03

ENGLISH-07

2. IC Notice

• The term “IC” before the radio certication number only signies that Industry

Canada technical specications were met. Operation is subject to the following

two conditions: (1) this device may not cause interference, and (2) this device

must accept any interference, including interference that may cause undesired

operation of the device.

• This Class B digital apparatus complies with Canadian ICES-003.

• Cet appareil numérique de la classe B est conforme á la norme NMB-003 du

Canada.

• For products available in the US and Canadian markets, only channels 1~11 are

available. You cannot select other channels.

IC RADIATION EXPOSURE STATEMENT:

• This equipment complies with IC RSS-102 radiation exposure limits set forth for

an uncontrolled environment. This equipment should be installed and operated

so there are at least 8inches (20cm) between the radiator and your body. This

device and its antenna(s) must not be co-located or operated in conjunction with

any other antenna or transmitter.

Open Source License Notice

• This device uses open source software. Open Source Licenses are available on

the product menu.

• Tap “Settings > Network > Software Update > Legal Information” on the device

for more details.

1_VR7000_EN_DJ68-00763C-10_USA.indd 7 2017-12-01 오후 4:46:04

ENGLISH-08

WARNING

Power related

f To prevent the risk of electric shock or

re:

– Do not damage the power cord.

– Do not pull the power cord too hard or

touch the power plug with wet hands.

– Use only power sources that provide

between 100 and 240 volts. Do not plug

the POWERbot into a multi-outlet power

strip. Do not place the power cord where it

can be stepped on, tripped over, or where

the POWERbot can run over it.

– Do not use a damaged power plug, power

cord, or loose power outlet.

f Clean dust or any foreign matter off the

prongs of the power plug.

– There is a risk of electric shock or

malfunction.

WARNING

Before use

f Do not use the POWERbot near

combustible materials.

– Do not place or use near candles, desktop

lamps, or replaces or near combustible

materials such as gasoline, alcohol, thinners

etc.

f The POWERbot is intended for specic

household use. Do not use it in an attic,

basement, storage area, industrial

building, outside, in places with moisture

(such as a bathroom or laundry room), on

a table or on shelves.

– The POWERbot can be damaged or

malfunction.

f Be sure the POWERbot does not pass

through or touch any kind of liquid.

– The POWERbot can be severely damaged

and it may contaminate other areas if the

wheels pass through liquid.

f Attach the boundary markers to places

where the POWERbot may fall such as

the top of a staircase or a bannister to

prevent product damage and injury.

– Please keep the cliff sensor clean at all

times for safety.

f Do not spill any liquid on the docking

station.

– There is a risk of re or electric shock.

f Do not use the docking station for

anything other than its intended purpose.

– There is a risk of re or severe damage to

the docking station.

f Always keep the cliff sensor clean for

your safety.

WARNING

In use

f If any abnormal sounds, smells, or smoke

come from POWERbot, immediately shut

off the POWERBOT using the emergency

switch on the bottom of POWERbot, and

then contact a Samsung service center.

WARNING

Cleaning and

maintenance

f If the power cord is damaged, contact a

Samsuing service center to get it replaced

by a certied repairman.

– There is a risk of re or electric shock.

f Contact a Samsung Electronics service

center if you need to replace the batteries.

– Using batteries from other products can

cause the POWERbot to malfunction.

CAUTION

Before use

f If a brush or brush cover is not assembled

correctly, scratches may occur on the

oor, or product malfunction may occur.

f Before operating the POWERbot, remove

the objects which could break such as

a frame, mirror, and porcelain items

so that the POWERbot works without

interruption.

f Insert the dustbin before using the

POWERbot.

Safety information

1_VR7000_EN_DJ68-00763C-10_USA.indd 8 2017-12-01 오후 4:46:04

ENGLISH-09

f For proper automatic recharging, do the

following:

– Always turn on the power of the docking

station.

– Install the docking station where the

POWERbot can nd it easily.

– Do not leave any object in front of the

docking station.

f When installing the docking station, do

not leave the cord on the oor where the

POWERbot can run over it.

f Do not use POWERbot on black colored

oors.

– The POWERbot may not be able to operate

normally.

f Do not place any objects within 1.6ft

(0.5m) of either side of the docking

station or within 3.3 ft (1m) of the front

of the docking station.

f Make sure the docking station's charging

contact is not damaged and is free of

foreign matter.

f Do not install the docking station in an

area with a dark oor.

– If the oor around the docking station is

dark, recharging is hindered.

f Move any obstacles that may disturb

POWERbot's movement (such as a

children's indoor swing or slide) before

cleaning.

f Do not use the POWERbot in a place

which is narrower than its turning radius

(1.6 ft/0.5 m or less).

f To clean all areas of your house, open all

rooms and attach the boundary markers

to places where the POWERbot could get

damaged such as a front door, veranda,

bathroom, or stairs.

f For areas with low clearance where

the POWERbot may get stuck, attach

the boundary markers to prevent the

POWERbot from getting in.

CAUTION

In use

f Using the POWERbot on thick carpet may

damage both the POWERbot and the

carpet.

– The POWERbot cannot pass over carpet that

is thicker than 0.4in (1cm).

f Do not use the POWERbot on tables or

other high surfaces.

– There is a risk of damage if it falls.

f The POWERbot may bump into chair or

desk legs. Move them out of the away for

faster, more efcient cleaning.

f When the POWERbot is operating, do not

lift it up or carry it to another area.

f Do not hold the POWERbot by its driving

wheels when carrying it to another area.

f Do not put any objects on top of the

POWERbot and camera since this may

cause the POWERbot to malfunction.

f Remove any large pieces of paper or

plastic bags from the area to be cleaned

before using the POWERbot since they

may block the POWERbot's intake.

f Do not aim the red pointer directly at

people or animals.

f Do not lie down near the POWERBOT

when it is running.

– Your hair may be caught in the brush,

resulting in physical injury.

CAUTION

Cleaning and

maintenance

f To prevent any damage to the POWERbot:

– Do not clean the POWERbot by spraying

water directly onto it or using benzene,

thinner, acetone or alcohol to clean it.

f Do not disassemble or try to repair the

POWERbot yourself. Repairs should only

be done by a certied repairman.

f Always keep the obstacle sensor, cliff

sensor, and camera clean.

– If foreign matter accumulates, the sensors

may malfunction.

1_VR7000_EN_DJ68-00763C-10_USA.indd 9 2017-12-01 오후 4:46:04

ENGLISH-10

1

Connect the

battery charger

jack to the

docking station

2

Connect the

power cord

to the battery

charger

The side with the sticker

attached must face down.

3

Connect the

power plug to

the outlet

Installation

The docking station must be plugged in and turned on at all times.

DC-IN

About 3.3 ft

(1 m)

About

1.6 ft

(0.5 m)

About

1.6 ft

(0.5 m)

Install the docking station in a place

without obstacles and where there is

no danger of falling.

1_VR7000_EN_DJ68-00763C-10_USA.indd 10 2017-12-01 오후 4:46:05

ENGLISH-11

Accessories

or

Remote control

(Optional)

Batteries (AAA type)

(Optional)

User manual Spare lter (Optional)

Docking station Power cord Battery charger Boundary markers

(Optional)

 Accessories may differ depending on the models.

 Refer to page 17 for the installation of boundary markers.

Installation note

Note

f Install the docking station in a place where the oor is level and the wall is straight.

f It is best to install the docking station along the grain of wooden oors.

f If the emergency switch is off, the POWERbot will not charge even if it is docked in the

docking station.

f Always turn on the power of the docking station.

– If power is not supplied to the docking station, the POWERbot cannot nd it and cannot

automatically recharge.

– If the POWERbot is left detached from the docking station, the battery will drain.

f If the POWERbot is in sleep mode, power will not come on even if the emergency switch is

turned off and then on. Press and hold the [Start/Stop] button on the POWERbot to turn the

sleep mode off.

1_VR7000_EN_DJ68-00763C-10_USA.indd 11 2017-12-01 오후 4:46:08

ENGLISH-12

After completely charging the POWERbot for the rst time (after purchase), it can be used for 60

min. in Nomal ( ) mode. (Refer to the page 41 for the charging time.)

Smart Charging

If the POWERbot's charge runs low while it is in Auto clean mode, it will automatically return to

the docking station to recharge, and then will return to the cleaning area after its battery is 2/3rds

charged. (Maximum: 2 times.)

Charging

1

Turn on the

emergency switch

on the bottom

You must turn on the

emergency switch to turn on

the POWERbot.

Press and release the

button.

2

Manually charge

the POWERbot by

placing it in the

docking station

Make sure the charging

pins on the POWERbot

and the docking station

are aligned.

3

Check the charging

status

For the SR1AM7010U



Series, the battery

indicator blinks at 1 second intervals

during charging. The indicator will remain

on when the battery is fully charged.

For SR1AM7040W / SR2AM70 Series,

each section of the " " will turn on

successively to indicate charging progress and

"FULL" will appear when charging is complete.

WARNING

• Rated input voltage of

this product is 100-

240V~.

<SR1AM7040W /

SR2AM70 Series>

<SR1AM7010U Series>

1_VR7000_EN_DJ68-00763C-10_USA.indd 12 2017-12-01 오후 4:46:09

ENGLISH-13

1. SR1AM7010U Series

If the battery indicator blinks at 0.4 sec. intervals,

the POWERbot will automatically return to the

docking station to recharge.

2. SR1AM7040W / SR2AM70 Series

When the battery indicator blinks during cleaning,

the POWERbot will return to the docking station to

charge itself automatically.

Automatic charging

You can command the POWERbot to

recharge at the docking station while it is

cleaning.

Recharging

You can manually charge the POWERbot by

placing it in the docking station.

Low battery (Lo)

Steps to take if automatic recharging is not occuring:

Reconsider the location of the docking

station when:

fthe docking station is located in a place where

the POWERbot cannot easily access it.

fthe distance between the docking station and

POWERbot is over 16.4ft (5m).

– It may take a long time for the POWERbot to

return to the docking station for recharging

Manually charge the POWERbot when:

fthe docking station is located in a corner

fthe battery is fully exhausted

fthe POWERbot is immobilized by an obstacle

(furniture, etc.)

fthe POWERbot can't climb a threshold near

the docking station (The maximum height of

a threshold the POWERbot can climb is about

0.6in (1.5cm)).

fthe battery indicator blinks and "Lo" is

displayed

fthe battery indicator blinks (Applicable to

SR1AM7010U Series)

fthe POWERbot is set to the Spot clean or

Manual clean mode

1_VR7000_EN_DJ68-00763C-10_USA.indd 13 2017-12-01 오후 4:46:09

ENGLISH-14

Using POWERbot

You must turn on the emergency switch on the bottom of the unit before using POWERbot.

Turning the power on/off

Press the button for more than 3seconds

Starting Auto clean mode

Press and release this button. The POWERbot moves

and automatically cleans the set areas only once.

 Stop cleaning: Press and release the button

Recharging/Energy-saving mode

fRecharging

You can command POWERbot to recharge at the docking station

automatically while it is cleaning by pressing this button.

fEnergy-saving mode

Refer to page 17.

Using Spot clean mode

The POWERbot cleans a localized area intensely.

WARNING

• When POWERbot is not used for 30 min.;

SR1AM70U / SR2AM70U series: Enters energy-saving mode.

SR1AM70W / SR2AM70W series: Automatically returns to the docking

station to be charged.

1_VR7000_EN_DJ68-00763C-10_USA.indd 14 2017-12-01 오후 4:46:10

ENGLISH-15

Selecting cleaning modes

Cleaning mode How to select

Displayed icons

SR1AM7040W

SR2AM70

SR1AM7010U

Auto clean

Spot clean

Repeat clean

 Press the [A,B type

],

[C type ] on the remote

controller rst, and then press

the [Start/Stop ].

-

Manual clean

 You can select manual clean

mode using the direction control

buttons on the remote control.

-

 If POWERbot fails to return to the docking station, it will enter energy-saving mode and the display

panel will be turned off.

 To exit the energy-saving mode, press the [Start/Stop

] or [Power ] button on the main body or

the remote control.

 If cleaning in Auto clean mode is completed within 15 minutes, POWERbot cleans 1 more time.

1_VR7000_EN_DJ68-00763C-10_USA.indd 15 2017-12-01 오후 4:46:13

ENGLISH-16

Cleaning method for each mode

About 4.9ft (1.5m)

Auto clean

Automatically cleans the

set areas only once.

 SR1AM7010U



series:

Cleans repeatedly

until the battery is

depleted.

Spot clean

Cleans a localized area

intensely. It can be used

to clean bread or cookie

crumbs.

Manual clean

You can move

POWERbot with the

remote control to clean

the desired spot.

 This function is not

available on the

SR1AM7010U series.

Repeat clean

Cleans repeatedly until

the battery is depleted.

 This function is not

available on the

SR1AM7010U series.

Note

f If you select Auto clean or Repeat clean, the POWERbot cleans the area near the docking station rst.

Using special cleaning functions

Cleaning

function

Operation

Displayed icons

SR1AM7040W

SR2AM70

SR1AM7010U

Intelligent

power control

 When the POWERbot detects a

carpet in normal mode, it will

automatically operate with

stronger suction power.

Edge clean

master

 When the POWERbot detects an

edge or corner in Auto clean or

Spot clean, the auto shutter tool

operates and approaches the

edge or corner section to clean.

fStraight edge (One time cleaning)

fCorner (Cleans twice)

Using POWERbot

1_VR7000_EN_DJ68-00763C-10_USA.indd 16 2017-12-01 오후 4:46:14

ENGLISH-17

About the boundary markers

To prevent the POWERbot from entering the following areas, place

the boundary markers on the oor in an shape at intervals of

about 5.9in (15cm).

About 5.9in

(15cm)

Boundary

markers

About 1.9in

(5cm)

About 5.9in (15cm)

Boundary

markers

Where a raised spot exceeds 1.9in (5cm) Where there is a slide, swing, replace, or any

ammable substance or moisture.

Above 0.6in (1.5cm)

boundary

markers

Boundary

markers

Where a threshold is higher than 0.6in (1.5cm) Where there is risk of falling such as near

stairs, porches, or guardrails.

Using Energy-saving mode

You can selectthe Energy-saving modeto save energy during battery charging.Energy-saving mode

turns off all functions except battery charging.Use it to reduce powerconsumptionwhile you are away

from home for an extended period of time.

How to select or cancel Displayed icon

Press for 5 sec.

 About 3seconds

later, the previous

indicator will

appear.

<SR1AM7010U

series only>

Blinking Blinking

Note

f If you select the Auto/Max/Manual clean mode or press the Point cleaning button, the

Energy-saving mode will be cancelled.

f When Energy-saving mode is on, setting the schedule will cancel Energy-saving mode.

– If you select the Energy-saving mode after setting the schedule, the schedule will not be cancelled.

f If the docking station is off, Energy-saving mode will be cancelled.

f If the battery is completely at, place the POWERbot on the docking station, and then press

the [Start/Stop

] button on the main body.

1_VR7000_EN_DJ68-00763C-10_USA.indd 17 2017-12-01 오후 4:46:17

ENGLISH-18

Using the remote control

[A Type] [B Type]

1 1

1, 2 1, 2

[C Type]

1

3

5

2

Refer to

page 24

4

6

1, 2

3 3

5 5

Refer to

page 23

Refer to

page 23

2 2

4

1_VR7000_EN_DJ68-00763C-10_USA.indd 18 2017-12-01 오후 4:46:18

ENGLISH-19

[A Type] / [B Type]/ [C Type]

1 Power / Recharging / Start/Stop

Power

Turn POWERbot's power on/off

Recharging

Select to recharge POWERbot at the docking station

automatically

Start/Stop

Select to start or stop the cleaning process

2 Cleaning modes

Auto clean

Select to clean all set areas only once and then have

the POWERbot automatically return to the docking

station.

Spot clean

Select to clean a localized area intensely

Repeat clean

Select to clean repeatedly until the battery becomes

very low and the battery level indicator blinks

3 Suction power

Turbo mode

Select to clean with the strongest suction power

Normal mode

Select to clean with moderate suction power

Quiet mode

Select to clean with lower operational noise

4 Additional function

Sound

Each time you press this button, Sound Effects 

Mute is selected in sequence

Star wars  Sound Effects  Mute

Remote control

Select to turn the Wi-Fi function on or off

 SR1AM7010U5 series only: Star wars (Mute function is not available.)

 Turning the emergency switch off and then on will not cancel or change the settings.

1_VR7000_EN_DJ68-00763C-10_USA.indd 19 2017-12-01 오후 4:46:22

ENGLISH-20

5 Manual clean mode & Direction control

Move forward

Select to move forward

Turn left

Select to turn left

Turn right

Select to turn right

 Moving backward is not available.

6 Point cleaning

Available only with C type remote controllers.

You can use the remote control to direct the POWERbot to clean a desired spot

while the POWERbot is cleaning.

Point the red light on the oor within 1.6ft (0.5m) of the POWERbot's location.

Press and hold the Point cleaning button to move the red light to the desired spot. The POWERbot

will follow the light while cleaning.

1.6ft

(0.5m)

Operating distance of the remote control

Height of the

remote control

Operating distance

Height of the

remote control

1.6ft (0.5m) 3.3ft (1m) 4.9ft (1.5m)

Operating

distance

About 4.9ft

(1.5m)

About 6.6ft

(2m)

About 9.8ft

(3m)

Inserting batteries

Open the battery cover by lifting it

up while pressing the locking tab.

Insert the batteries as shown in

the illustration, and then close the

cover until it clicks into place.

Using the remote control

1_VR7000_EN_DJ68-00763C-10_USA.indd 20 2017-12-01 오후 4:46:25

La page charge ...

Samsung SR1AM7040WG Manuel utilisateur

Ce manuel convient également à

Samsung SR1AM7040WG Manuel utilisateur

dans d''autres langues

Documents connexes