Samsung SR2AK9350U Manuel utilisateur

SR2AJ90U Series

POWERbot

user manual

imagine the possibilities

Thank you for purchasing a Samsung product.

English

 Before operating this unit, please read the instructions carefully.

 For indoor use only.

1_SR2AJ90@@U_EN_00740B-00_USA.indd 1 2015-08-18 오전 10:09:33

ENGLISH-02

Contents

03

Safety information

08

Installation

Accessories

10

Charging

Automatic charging / Recharging / Low

battery

12

Using POWERbot

Turning the power on/off / Start Auto

clean mode / Starting Spot clean mode /

Recharging / Selecting cleaning modes /

Using Energy-saving mode

15

Using the remote control

Power/Recharging / Cleaning modes /

Suction modes / Additional functions /

Direction control

16

Name of each part

Top / Bottom / Display panel

17

Cleaning and maintaining

Cleaning the dustbin / Cleaning the sensors and

the camera / Cleaning the Pet brush / Cleaning

the Driving wheel

19

Notes and cautions

Charging / In use / Cleaning and maintenance /

About battery

21

Information codes

22

Troubleshooting

23

Open Source Announcement

23

Specifications

1_SR2AJ90@@U_EN_00740B-00_USA.indd 2 2015-08-18 오전 10:09:33

ENGLISH-03

Safety information

SAFETY INFORMATION

WARNING

• Before operating the appliance, please read this manual thoroughly and retain it

for your reference.

WARNING

• Because these following operating instructions cover various models, the

characteristics of your vacuum cleaner may differ slightly from those described in

this manual.

CAUTION/WARNING SYMBOLS USED

WARNING

Indicates that a danger of death or serious injury exists.

CAUTION

Indicates that a risk of personal injury or material damage exists.

OTHER SYMBOLS USED

NOTE

Indicates that a risk of personal injury or material damage exists.

State of California Proposition 65 Warning (US only)

WARNING

This product contains chemicals known to the State of California to cause

cancer and reproductive toxicity.

L i - i o n

For battery recycling go to call2recycle.org;

or call 1-800-822-8837

1_SR2AJ90@@U_EN_00740B-00_USA.indd 3 2015-08-18 오전 10:09:33

ENGLISH-04

Safety information

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should be observed, including the

following:

READ ALL INSTRUCTIONS BEFORE USING YOUR POWERbot.

Unplug from outlet when not in use and before conducting maintenance.

WARNING: to reduce the risk of fire, electric shock, or injury:

GENERAL

•Use only as described in this manual.

•Do not operate POWERbot or the adapter / docking station if it has been damaged in

any way.

•If the vacuum cleaner is not working as it should, has been dropped, damaged, left

outdoors, or dropped in water, return it to a customer care center.

•Do not handle the adapter / docking station or POWERbot with wet hands.

•Use only on dry, indoor surfaces.

•This appliance can be used by children aged from 8 years and above and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge

if they have been given supervision or instruction concerning use of the appliance in a

safe way and understand the hazards involved.

•Children shall not play with the appliance. Cleaning and user maintenance shall not be

made by children without supervision.

Adapter / Docking station

•Do not modify the polarized plug to fit a non-polarized outlet or extension cord.

•Do not use outdoors or on wet surfaces.

•Unplug the adapter / docking station from the outlet when not in use and before

servicing.

•Use only the adapter / docking station supplied by the manufacturer to recharge.

•Do not use with a damaged cord or plug or a loose power outlet.

•Do not pull or carry by the cord, use the cord as a handle, close the door on the cord,

or pull the cord around sharp edges or corners. Keep the cord away from heated

surfaces.

•Do not use extension cords or outlets with inadequate current carrying capacity.

•Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.

•Do not mutilate or incinerate batteries as they will explode at high temperatures.

•Do not attempt to open the adapter / docking station. Repairs should only be carried

out by a qualified customer care center.

1_SR2AJ90@@U_EN_00740B-00_USA.indd 4 2015-08-18 오전 10:09:33

ENGLISH-05

•Do not expose the adapter / docking station to high temperatures or allow moisture or

humidity of any kind to come into contact with the adapter / docking station.

POWERbot

•Do not pick up hard or sharp objects such as glass, nails, screws, coins, and etc.

•Do not use without a filter in place. When servicing the unit, never put fingers or other

objects into the fan chamber in case the unit accidentally turns on.

•Do not put any objects into openings. Do not use with any openings blocked; keep

openings free of dust, lint, hair, and anything that may reduce air flow.

•Do not pick up toxic materials (chlorine bleach, ammonia, drain cleaner, etc.).

•Do not pick up anything that is burning or smoke, such as cigarettes, matches, or hot

ashes.

•Do not use to pick up flammable or combustible liquids such as gasoline, nor use on

areas where they may be present.

•Locations with candles or desk lamps on the floor.

•Locations with unattended fires (fire or embers).

•Locations with distilled alcohol, thinner, ashtrays with burning cigarettes, etc.

•Do not use POWERbot in an enclosed space filled with vapours given off by oil based

paint, paint thinner, moth proofing substances, flammable dust, or other explosive or

toxic vapours.

•Leaks from battery cells can occur under extreme usage or temperature conditions.

If the liquid gets on skin, wash quickly with water. If the liquid gets into the eyes,

flush them immediately with clean water for a minimum of 10 minutes. Seek medical

attention.

SAVE THESE INSTRUCTIONS

POLARIZED PLUG INSTRUCTIONS

•To reduce the risk of electric shock, this appliance has a polarized plug (one blade is

wider than the other). This plug will fit in a polarized outlet only one way. If the plug

does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified

electrician to install a proper outlet. Do not modify the plug in any way.

1_SR2AJ90@@U_EN_00740B-00_USA.indd 5 2015-08-18 오전 10:09:33

ENGLISH-06

WARNING

Power related

f Please prevent any risk of electric shock or

fire.

– Do not damage the power cord.

– Do not pull the power cord too hard or touch

the power plug with wet hands.

– Do not use a power source other than 100-

240 V~ and also do not use a multi outlet to

supply power to number of devices at the same

time. (Do not leave the cord carelessly on the

floor.)

– Do not use a damaged power plug, power cord

or loose power outlet.

f Clean dust or any foreign matters on the pin

and contact part of the power plug.

– There is a risk of electric shock or malfunction.

WARNING

Before use

f Do not use POWERbot near combustible

materials.

– Place near candle, desktop lamps, fireplace or

near combustible materials such as gasoline,

alcohol, thinners etc.

f The POWERbot is intended for household

use therefore do not use it in an attic,

basement, storage, industrial building, out of

indoor space, places with moisture (such as

bathroom, laundry), on the table or shelves.

– The POWERbot can be damaged or

malfunction.

f Be sure POWERbot does not pass through or

touch any kind of liquids.

– The POWERbot can be severely damaged and

it may contaminate other areas if the wheels

pass through liquid.

f Do not spill any liquids on the docking station.

– There is a risk of fire or electric shock.

f Do not use the docking station for anything

other than its intended purpose.

– There is a risk of fire or severe damage to the

docking station.

f Always keep the cliff sensor clean for your

safety.

WARNING

In use

f If any abnormal sounds, smells or smoke

come from POWERbot, immediately shut

off the emergency switch at the bottom of

POWERbot and contact a service center.

WARNING

Cleaning and

maintenance

f When power cord is damaged, contact a

service center to get it replaced by certified

repairman.

– There is a risk of fire or electric shock.

f Please check with a Samsung Electronics

service center when exchanging batteries.

– Using batteries from other products can cause

malfunction.

Safety information

1_SR2AJ90@@U_EN_00740B-00_USA.indd 6 2015-08-18 오전 10:09:33

ENGLISH-07

CAUTION

Before use

f Insert the dustbin before using POWERbot.

f Be careful with the followings for proper

automatic recharging.

– Always turn on the power of the docking

station.

– Install the docking station where POWERbot

can easily find.

– Do not leave any object in front of the docking

station.

f When installing the docking station, do not

leave the cord carelessly on the floor since

POWERbot may get tangled by it.

f Do not use POWERbot on black colored

floors.

– The POWERbot may not be able to operate

normally.

f Do not pick up POWERbot by the dustbin

holder.

f Do not place any objects within 0.5 m to both

sides and 1 m to the front of the docking

station.

f Make sure the docking station's charging

contact is not damaged or have any foreign

matters on it.

f Do not install the docking station in an area

with a dark floor.

– If the floor around the docking station is dark,

recharging is hindered.

f Move any obstacles that may disturb

POWERbot's movement (such as children's

indoor swing or slides) before cleaning.

CAUTION

In use

f Using POWERbot on thick carpet may

damage both POWERbot and the carpet.

– The POWERbot cannot pass over carpet that is

thicker than 1 cm.

f Do not use POWERbot on tables or other

high surfaces.

– There is a risk of damage if it falls.

f The POWERbot may bump into chair, desk

legs therefore move them away for faster and

efficient cleaning.

f When POWERbot is operating, do not lift it up

or carry it to another area.

f Do not hold by driving wheels of POWERbot

when carrying it to another area.

f Do not put any objects on top of POWERbot

since it may cause malfunction.

f Remove any large papers or plastic bags

immediately when using POWERbot since

they may block the intake.

f Do not aim the red pointer directly at people

or animals.

CAUTION

Cleaning and

maintenance

f Prevent any damage to POWERbot by

complying the followings.

– Do not clean POWERbot by spraying water

directly onto it or use benzene, thinner, acetone

or alcohol to clean it.

f Do not disassemble or repair POWERbot.

This should only be done by a certified

repairman.

f Always keep the obstacle sensor and cliff

sensor clean.

– If foreign matter accumulates, sensors may

malfunction.

1_SR2AJ90@@U_EN_00740B-00_USA.indd 7 2015-08-18 오전 10:09:33

ENGLISH-08

1

Connect the

adapter jack

to the docking

station

2

Connect the

power cord to

the adapter

When using the adapter,

the side with the sticker

attached must face down.

3

Connect the

power plug to

the outlet

The power indicator lamp

(Red) will turn on.

Installation

The docking station must be plugged in and turned on at all times.

DC-IN

Power lamp (Red)

About 1 m

About 0.5 m

Install the docking station in a place

without obstacles and danger of

falling.

1_SR2AJ90@@U_EN_00740B-00_USA.indd 8 2015-08-18 오전 10:09:34

ENGLISH-09

Accessories

Remote control Batteries (AAA type) User manual Spare filter

(SR2AJ9020U Series)

Cleaning brush Power cord Adapter

Note

f Install the docking station in a place where the floor and wall are level.

f It is best to install the docking station along the grain of wooden floors.

f If the emergency switch is off, the POWERbot will not charge even if it is docked on the docking

station.

f Always turn on the power of the docking station.

– If power is not supplied to the docking station, the POWERbot cannot find it and cannot automatically

recharge.

– If the POWERbot is left detached from the docking station, the battery will drain naturally.

f If the POWERbot is in sleep mode, power will not come on even if the emergency switch is turned

off and then on. Press and hold the [Start/Stop] button on the POWERbot to turn off the sleep

mode.

1_SR2AJ90@@U_EN_00740B-00_USA.indd 9 2015-08-18 오전 10:09:34

ENGLISH-10

Charging light turns green during charging.

It takes approximately 160 minutes to

completely charge the POWERbot when

charging it for the first time after purchase.

Once charged, the POWERbot can be used

for approximately 60 minutes.

Charging

1

Turn on the

emergency switch

on the bottom

You must turn on the

emergency switch to turn on

the POWERbot.

2

Manually charge

the POWERbot by

placing it on the

docking station

Make sure the charging pins

on the POWERbot and the

docking station are aligned.

3

Check the

charging status

“ ” appear

in the sequence to show

charging progress. All the 6

icons appear when charging

is complete.

WARNING

• Rated input voltage of this product

is 100-240 V~.

1_SR2AJ90@@U_EN_00740B-00_USA.indd 10 2015-08-18 오전 10:09:35

ENGLISH-11

When the battery indicator blinks

during cleaning, the POWERbot

will return to the docking station to

charge itself automatically.

Automatic charging

You can command the POWERbot

to recharge at the docking station

while it is in cleaning.

Recharging

Manually charge the POWERbot by

placing it on the docking station.

Low battery

Steps to take if recharging not occuring:

Check the installation status of the

docking station when:

fthe docking station is located in a place where the

POWERbot cannot easily access it.

fthe distance between the docking station and

POWERbot is over 16.5 ft (5 m).

- It may take a long time for POWERbot to return to

the docking station for recharging

Manually charge the POWERbot when:

fthe docking station is located in a corner

fthe battery is fully exhausted

fthe POWERbot is immobilized by an obstacle

(furniture etc.)

fthe POWERbot can't climb a threshold near the

docking station (The maximum height of a threshold

the POWERbot can climb is about 0.6 inches

(1.5 cm).)

fthe battery indicator blinks

fthe POWERbot is set to the Spot clean or Manual

clean mode

1_SR2AJ90@@U_EN_00740B-00_USA.indd 11 2015-08-18 오전 10:09:35

ENGLISH-12

Using POWERbot

You must turn on the emergency switch on the bottom of the unit before using POWERbot.

Turning the power on/off

Press the button for more than

3 seconds

Starting Auto clean mode

Press and release this button. Cleans space

dividing until the battery is depleted .

 Stop cleaning: Press and release the button

Recharging

fRecharging

You can command POWERbot to recharge at the

docking station automatically while it is cleaning

by pressing this button.

Starting Spot clean mode

Press and release this button. The POWERbot

cleans a localized area intensely.

WARNING

• When POWERbot is not used for

30 minutes, power will turn off

automatically.

1_SR2AJ90@@U_EN_00740B-00_USA.indd 12 2015-08-18 오전 10:09:36

ENGLISH-13

Cleaning mode How to select Displayed icon

Auto clean

Spot clean

Manual clean

 The movement and direction of the

POWERbot is controlled by the remote

control.

 When the POWERbot is being charged, you can select the Auto clean

mode only.

 If the POWERbot fails to return to the charger, it will be turned into the

sleep mode. Then the display panel of the main body will be turned

off. Press [Start/Stop] or [Power] button to cancel the sleep mode.

 Charging and cleaning times may differ according to conditions of

use.

<Displayed icons in the sleep

mode>

Cleaning method for each modes

About 59 inches (1.5 m)

Auto clean

Cleans space dividing until the

battery is depleted .

Spot clean

Cleans a localized area

intensely. It can be used to

clean bread or cookie crumbs.

Manual clean

You can control the POWERbot

with the remote control and

direct it to clean a desired spot.

Selecting cleaning modes

1_SR2AJ90@@U_EN_00740B-00_USA.indd 13 2015-08-18 오전 10:09:36

ENGLISH-14

Using Energy-saving mode

You may select the Energy-saving mode when you go out for a long time or want to save energy.

You can select or cancel the Energy-saving mode only while the POWERbot is docked on the docking station.

How to select or cancel Displayed icon

Press for 5 sec.

 About 3 seconds later,

the previous indicator will

appear.

 When the POWERbot is in the Energy-saving mode, the green lamp of the docking station will blink.

Note

f If you select the Auto/Manual clean mode, the Energy-saving mode will be cancelled.

f If the power of the docking station is off, the Energy-saving mode will be cancelled.

1_SR2AJ90@@U_EN_00740B-00_USA.indd 14 2015-08-18 오전 10:09:37

ENGLISH-15

Using the remote control

1

2

5

3

4

1 Power/Recharging

Power

Turn POWERbot's power on/off

Recharging

Select to recharge POWERbot at the

docking station while it is cleaning.

Start/Stop

Select to start or stop cleaning

2 Cleaning modes

Auto clean

Cleans space dividing until the battery

is depleted .

Spot clean

Select to clean a localized area

intensely

3 Suction modes

Quiet mode

Select to clean with lower operational

noise

Normal mode

Select to clean with normal suction

power

4 Additional functions

Sound

Each time you press this button,

Sound Effects  Mute is selected in

this sequence.

5 Direction control

Forword

movement

Select to move forward

Left turn

Select to turn left

Right turn

Select to turn right

 Moving backward is not available

Inserting batteries

Open the battery cover by lifting

it up while pressing the locking

tab, and then insert the batteries

as shown in the illustration. Then,

close the cover until it clicks into

place.

1_SR2AJ90@@U_EN_00740B-00_USA.indd 15 2015-08-18 오전 10:09:37

ENGLISH-16

Name of each part

1

4

5

3

6

7

8

2

3

Top

1. Display panel

2. Dustbin holder

3. Remote control signal receiver

4. Obstacle sensor

5. Dustbin

6. Camera

7. Dustbin handle

8. Bumper sensor

1

4

2

6

5

4

7

4

8

9

3

Bottom

1. Charge pins

2. Pet brush

3. Pet brush cover

4. Cliff sensor

5. Roller

6. Battery cover

7. Pet brush cover button

8. Driving wheel

9. Emergency switch

8 94 765

1

2

10

3

11

12

Display panel

1. Mute

2. Information indicator

3. Battery indicator

4. Auto clean

5. Spot clean

6. Manual clean

7. Quiet mode

8. Normal mode

9. Recharging

10. Spot cleaning button

11. Start/Stop button

12. Recharging button

1_SR2AJ90@@U_EN_00740B-00_USA.indd 16 2015-08-18 오전 10:09:38

ENGLISH-17

Cleaning and maintaining

You must turn off the emergency switch before cleaning POWERbot.

Cleaning the dustbin

1

Remove the dustbin

2

Remove the dustbin

cover

3

Remove dust in the

dustbin and cyclone

unit

"Click"

4

Detach the cyclone unit

from the dustbin cover,

and then wash the

dustbin and the filter

5

Reassemble the

dustbin

6

Reinsert the dustbin

into the main body until

it clicks

Cleaning the sensors and the camera

Lightly wipe with soft cloth. Do not use water or cleaning solutions.

Camera

Front sensor

window

Rear sensor

window

Cliff sensors

1_SR2AJ90@@U_EN_00740B-00_USA.indd 17 2015-08-18 오전 10:09:40

ENGLISH-18

Cleaning the Pet brush

1

Remove the Pet brush

cover

2

Remove the Pet brush

3

Clean the Pet brush

ON

OFF

ON

OFF

4

Reassemble the Pet

brush

5

Reassemble the Pet

brush cover

Cleaning the Driving wheel

1

Put a soft cloth on the floor and place

POWERbot upside-down on the cloth.

2

Use a blunt rod or tweezers to remove foreign

matter.

1_SR2AJ90@@U_EN_00740B-00_USA.indd 18 2015-08-18 오전 10:09:41

ENGLISH-19

Notes and cautions

Charging

Note

f If the battery overheats during charging, it

may take longer to charge.

f When automatic charging is not working, do

the following:

– Turn the emergency switch (on the bottom of

POWERbot) off and on again.

– Unplug the docking station's power plug and

then plug it back on.

– Unplug the docking station, and then check

whether there is any foreign matter on the

charge pins and clean POWERbot and the

charge pins of the docking station with a dry

cloth or rag.

– Check for any obstacles such as reflective

objects, chairs, etc. near the docking station.

f If POWERbot is left detached from the

docking station, the battery will drain naturally.

– Try to keep POWERbot being charged on

the docking station. (However, turn off the

emergency switch and leave the docking

station unplugged when planning to leave the

house for long periods of time by going on a

business trip or vacation, etc.)

In use

Note

f The POWERbot may get caught on

thresholds, etc. during cleaning.

– To restart operation, shut off the emergency

switch, move the POWERbot to an area where

it can move easily, and then turn on the power

again.

f The POWERbot cannot completely clean

areas it cannot enter, such as corners,

between the wall and sofa, etc.

– Please use another cleaning tool to clean them

regularly.

f The POWERbot cannot vacuum clumps of

dirt, so some may remain on the floor after

cleaning.

– Please use another cleaning tool to clean them

regularly.

f If the battery becomes low during Auto clean

mode, POWERbot will recharge and finish

cleaning the remaining area after recharging.

(Repeat cleaning frequency: 1 time)

f You cannot select and have the POWERbot

execute Spot/Manual clean mode while it is

charging.

f Do not unnecessarily move the POWERbot or

press buttons while it is in Auto clean mode. It

assumes that cleaning is complete and starts

cleaning again from the beginning.

f Close doors before cleaning with the

POWERbot. The POWERbot can enter

rooms through thresholds even though the

thresholds are below 5 cm.

f Try not to use the POWERbot at areas near

slides, indoor swing, pots, fireplaces, or

places with flame or moisture.

– If not, it may cause the loss of property.

f Do not lie down around the POWERBOT that

is running.

– Your hair may be caught in the Pet brush,

resulting in physical injury.

1_SR2AJ90@@U_EN_00740B-00_USA.indd 19 2015-08-18 오전 10:09:41

ENGLISH-20

Cleaning and maintenance

Note

f If you washed the dustbin and filter with water

– Dustbin: Completely wipe out the water.

– Filter: Completely dry it in the shade before

using.

f Purchase a filter at authorized Samsung

service centers if you need more filters.

Caution

f Watch your fingers when attaching or

detaching the filter, since they may get stuck

in the dustbin's intake.

f To avoid blockages by foreign matter, do not

let the POWERbot vacuum up toothpicks,

cotton swabs etc.

f If it is difficult to remove foreign matter

from the Pet brush, contact an authorized

Samsung service center.

f Since the Pet brush removes dirt from the

floor during cleaning, foreign matter such as

thread, long hair, etc. may get caught in it. For

the best cleaning results, check and clean it

regularly.

About the battery

Note

f Purchase batteries at authorized Samsung

service centers and check for the genuine

part symbol ( ) and model name

before purchasing.

f This battery is exclusively for the Samsung

Electronics POWERbot. Do not use it for any

other product.

f Do not disassemble or modify the battery.

f Do not throw the battery out in fire or heat it.

f Do not connect any metallic object to the

charging contacts (+, -).

f Store the battery indoors (at 32 °F~104 °F).

f If the battery malfunctions, do not

disassemble it yourself. Contact your nearest

Samsung service center.

f Battery charging time and usage time may

decrease the more the battery is used. If the

battery’s lifespan has been exceeded and it

no longer chargers properly, have it replaced

at a Samsung service center.

f The battery warranty period is 6 months from

the date of purchase.

1_SR2AJ90@@U_EN_00740B-00_USA.indd 20 2015-08-18 오전 10:09:41

La page charge ...

Samsung SR2AK9350U Manuel utilisateur

Samsung SR2AK9350U Manuel utilisateur

dans d''autres langues

Documents connexes