Perle IRG5520 LTE Guide d'installation

Marque: Perle

Modèle: IRG5520 LTE

Taper: Guide d'installation

Perle IRG5520/5520+/5521/5521+ Series

Router Hardware Installation Guide

Updated: Jan 2020

Version A.01.24, 2020

Document Part#:5500449-10

www.perle.com

Perle IRG5520/5520+/5521/5521+ Series Router Hardware Installation Guide

Preface

Audience

This guide is for the network or computer technician responsible for installing the Perle router also

generically referred to as the IRG552x within this document. All “+” models support worldwide

global coverage for LTE. Models IRG5521/5521+ also have integrated Wireless LAN 2.4/5 GHz

capabilities. Familiarity with the concepts and terminology of LTE, GNSS, Ethernet and LAN (local

area networks) is required.

Purpose

Perle routers provide users, networking equipment as well as M2M & IoT appliances with network

connectivity for fixed locations (i.e. buildings, POS, Kiosks, …etc) and mobile (i.e. vehicle, trains,

robots) applications. When used in vehicular applications, the router provides connectivity and is not

involved in the operation of the vehicle or direct interaction with the operators.

This document describes the hardware and physical characteristics of the Perle IRG552x Series of

Routers. It covers hardware features as well as installation and operation. This document does not

cover how to configure your Perle IRG552x router. Information to configure your Perle router can be

found in the Perle IRG5000 Series Router User’s Guide and the Perle IRG5000 Series Router CLI

Refernce Guide on the Perle website. Quick Start information can be found in the IRG552x Cellular

LTE Router Quick Start Guide that came with your product.

Key Features

• Supports bridging/switching and routing

• LTE coverage spanning 21 frequency bands in North America/EMEA (IRG5520/5521) and

30 frequency bands for global coverage (IRG5520+/5521+)

• Fully automatic network switching supporting dual network SIMs

• Routing with Primary/Backup route

• LTE and VPN Fail-over

• Provides network connectivity via LTE, Ethernet, USB-C and Serial

• Active GPS for tracking equipment

• Low Voltage Standby function to prevent battery drain

• One GPIO pin for remote monitoring/control and one IGN (Ignition) pin

• Two digital Inputs and one Relay contact

• RS485 half-duplex capabilities

• Wireless LAN 2.4/5 GHz support (models IRG5521/5521+)

• Security via remote authentication (Radius and TACACS+)

• Processor Power Saving Mode – this feature optimizes idle power consumption, saving

energy by reducing performance where possible

• Power Saving Features including; LED power saving mode, Smart Standby Mode, Power

saving strategies such as turning off unused interfaces (USB, Serial, Ethernet), turning off

GPS and adjusting the Ethernet rate

• Meets industry-grade certifications

Perle IRG5520/5520+/5521/5521+ Series Router Hardware Installation Guide

Preface

Additional Documentation

Document Conventions

This document contains the following conventions:

Most text is presented in the typeface used in this paragraph. Other typefaces are used to help you

identify certain types of information. The other typefaces are:

Note: Means reader take note: notes contain helpful suggestions.

Caution: Means reader be careful. In this situation, you might perform an action that could result in

equipment damage or loss of data.

Warning: IMPORTANT SAFETY INSTRUCTIONS

Means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be

aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing

accidents.

Important Notice

Due to the nature of wireless communications, transmission and reception of data can never be

guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant

delays or losses of data are rare when cellular devices such as the Perle IRG552x Series Routers are

used in a normal manner with a well-constructed network. The Perle IRG552x Series Routers should

not be used in situations where failure to transmit or receive data could result in damage of any kind

to the user or any other party, including but not limited to personal injury, death, or loss of property.

Perle accepts no responsibility for damages of any kind resulting from delays or errors in data trans-

mitted or received using our products.

Safety and Hazards

The driver or operator of any vehicle should not operate the IRG552x while in control of a vehicle.

Doing so will detract from the driver or operator's control and operation of that vehicle. The IRG552x

is listed to UL121201 and CSA C22.2 No. 213 and are suitable for use in Class I, Division 2, Groups

A, B, C and D Hazardous Locations.

The following warnings and instructions apply:

Limitation of Liability

The information in this manual is subject to change without notice and does not represent a commit-

ment on the part of Perle for any and all direct, indirect, special, general, incidental, consequential,

punitive or exemplary damages including, but not limited to loss of profits or revenue or anticipated

profits or revenue arising out of the use or inability to use any Perle IRG552x series router even if

Document Description

Perle IRG5000 Series Router User’s

Guide

User guide explaining how to configure the IRG552x

features using the Web Manager application. New users

should use this method to configure the router.

Perle IRG5000 Series Router CLI

Refernce Guide

Command Line Interface Reference Guide using CLI

commands to configure the IRG552x (this is an advanced

way to configure the router).

III

Perle IRG5520/5520+/5521/5521+ Series Router Hardware Installation Guide

Preface

Perle has been advised or the possibility of such damages or they are

foreseeable or for claims by any third party.

Notwithstanding the foregoing, in no event shall Perle aggregate liability arising under or in connec-

tion with the Perle product, regardless of the number of events, occurrences, or claims giving rise to

liability, be in excess of the price paid by the purchaser for the Perle

product.

Windows® is a registered trademarks of Microsoft Corporation.

Other trademarks are the property of their respective owners

General cautions and warnings

Warning: Power sources must be off prior to beginning the power connection steps. Read the

installation instructions before you connect the unit to its power source.

Avertissement: Les sources d'alimentation doivent être éteintes avant de commencer les étapes de

connexion d'alimentation. Veuillez lire les instructions d’installation avant de connecter l’appareil à

sa source d’alimentation.

Warning: Ensure that the voltage and current ratings of the intended power source are appropriate for

the IRG552x Series of Routers as indicated on the product label.

Avertissement: Assurez-vous que les valeurs nominales de tension et de courant de la source d'ali-

mentation prévue conviennent aux routeurs de la série IRG552x, comme indiqué sur l'étiquette du

produit.

Warning: Ensure that the installation and electrical wiring of the equipment is performed by trained

and qualified personnel and that the installation complies with all local and national electrical codes.

Avertissement: Assurez-vous que l'installation et le câblage électrique de l'équipement sont effectués

par du personnel formé et qualifié et que l'installation est conforme à tous les codes électriques locaux

et nationaux.

Warning: This equipment must be used in the matter specified by the manufacturer.

Avertissement: Cet équipement doit être utilisé dans les matières spécifiées par le fabricant.

Warning: In case of malfunction or damage, no attempts at repair should be made by the user. Do not

dismantle this product. In case of malfunction or damage, contact Perle Technical support at

https://www.perle.com/support_services/support_request.aspx

or email at

https://www.perle.com/support_services/support_request.aspx#form

IEC 60417-5041 (2002-10) Caution, hot surface

Refer to manual/safety

Perle IRG5520/5520+/5521/5521+ Series Router Hardware Installation Guide

Preface

Avertissement: En cas de dysfonctionnement ou de détérioration, aucune tentative de réparation ne

doit être effectuée par l'utilisateur. Ne démontez pas ce produit. En cas de dysfonctionnement ou de

dommage, contactez le support technique de Perle à l'adresse

https://www.perle.com/support_services/support_request.aspx

ou par courrier électronique à

https://www.perle.com/support_services/support_request.aspx#form

Warning: If the ambient temperature is to exceed 50°C (122°F), the unit should be installed in a

restricted access location where access can only be gained by service personnel or users who have

been instructed about the reasons for the restrictions applied to the location and about any precautions

that shall be taken; and access is through the use of a tool or lock and key, or any means of security,

and is controlled by the authority responsible for the location.

Avertissement: Si la température ambiante doit dépasser 50 ° C, l'unité doit être installée dans un

emplacement à accès restreint, auquel seul le personnel de service ou les utilisateurs informés des rai-

sons des restrictions appliquées peuvent accéder. sur le lieu et sur les précautions à prendre; et l'accès

se fait au moyen d'un outil ou d'un verrou et d'une clé, ou de tout moyen de sécurité, et est contrôlé

par l'autorité responsable du lieu.

Warning: The working voltage inputs are designed for operation with Safety extra low Voltage

(SELV). Connect only to SELV circuits with voltage restrictions in line with IEC/EN 62368-1.

Avertissement: Les entrées de tension sont conçues pour fonctionner avec une tension de sécurité

très basse (SELV). Connectez uniquement aux circuits SELV avec des restrictions de tension con-

formes à IEC / EN 62368-1.

Warning: For equipment installed within the same end-product enclosure ensure leads are segregated

or insulated the leads from different circuits.

Avertissement: Pour les équipements installés dans le même boîtier de produit final, assurez-vous

que les conducteurs sont séparés ou isolés des conducteurs de circuits différents.

Hazardous Location Warnings

Specific Conditions of Use

1. The IRG5520/5520+/5521/5521+ Routers are intended for installation into an IECEx/ATEX

certified and IP54 minimum rated enclosure in accordance with IEC/EN 60079-0 and accessible only

by the use of a tool. Les modèles de routeurs IRG5520/5520+/5521/5521+ sont destinés à être

installés dans un boîtier certifié IECEx/ATEX qui conforme à la norme IP54 conformément à la

norme IEC/EN 60079-0 et accessible uniquement à l'aide d'un outil.

2. The equipment shall only be used in an area of not more than pollution degree 2, as defined in

IEC/EN 60664-1. L'équipement ne doit être utilisé que dans une zone où le degré de pollution n'est

pas supérieur à 2, tel que défini dans la IEC/EN 60664-1.

Warning: These devices are open-type devices that are to be installed in an enclosure with tool

removable cover or door, suitable for the environment.

Avertissement: Ces périphériques sont des périphériques de type ouvert à installer dans un boîtier

avec un couvercle ou une porte amovible pour outils, adapté à l'environnement.

Perle IRG5520/5520+/5521/5521+ Series Router Hardware Installation Guide

Preface

Warning: This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D, or only non

hazardous locations.

Avertissement: Cet équipement est adapté à une utilisation dans les zones non dangereuses de classe

I, division 2, groupes A, B, C, D

Warning: WARNING-EXPLOSION HAZARD - Do not connect or disconnect equipment unless

power has been removed or the area is known to be non-hazardous.

Avertissement: DANGER D'EXPLOSION ET D'AVERTISSEMENT - Ne pas connecter ou decon-

necter l'équipement tant que l'alimentation n'est pas débranchée ou que la zone n'est pas dangereuse.

Warning: WARNING-EXPLOSION HAZARD - Substitution of any components on this unit may

impair suitability for Class I, Division 2.

Avertissement: DANGER DANGER D’EXPLOSION - La substitution de tout composant de cet

appareil peut compromettre l’adéquation à la Classe I, Division 2.

Warning: Power supply of the equipment must be rated appropriately (see Appendix for specifica-

tions) with limited power. Limited power means complying with one of the following requirements.

Class 2 circuit according to Canadian Electrical Code, Part 1, C22.1

Class 2 circuit according to National Electrical Code, NFPA-70

Limited Power Supply (LPS) according to EN/IEC 60950-1;

Limited-energy circuit according to EN/IEC 61010-1

Avertissement: l'alimentation de l'équipement doit être correctement dimensionnée (voir annexe

pour les spécifications) avec une puissance limitée. Une puissance limitée signifie que vous vous con-

formez à l'une des exigences suivantes.

Circuit de classe 2 selon le code électrique Canadien, partie 1, C22.1

Circuit de classe 2 selon le code électrique national NFPA-70

Alimentation électrique limitée (LPS) selon EN / IEC 60950-1;

Circuit à énergie limitée selon EN / IEC 61010-1

Warning: If this equipment is used in a manner not specified by the manufacturer, the protection

provided by the equipment may be impaired.

Avertissement: Si cet équipement est utilisé d'une manière non spécifiée par le fabricant, la protec-

tion fournie par l'équipement peut être altérée.

Warning: In case of malfunction or damage, no attempts at repair should be made. Do not dismantle

the product. All repairs need to be made by a qualified Perle representative. Contact Perle Systems

Technical support at https://www.perle.com/support_services/support_request.aspx or email at

https://www.perle.com/support_services/support_request.aspx#form

Avertissement: En cas de dysfonctionnement ou de dommage, aucune tentative de réparation ne doit

être effectuée. Ne démontez pas le produit. Toutes les réparations doivent être effectuées par un

représentant qualifié de Perle. Contactez le support technique de Perle Systems à l'adresse

https://www.perle.com/support_services/support_request.aspx ou par courrier électronique à

https://www.perle.com/support_services/support_request.aspx#form

Warning: This router is not intended for use close to the human body. The unit should be mounted in

such that Antennas are at least 20cm (8 inches) away from any person.

Perle IRG5520/5520+/5521/5521+ Series Router Hardware Installation Guide

Preface

Avertissement: Ce routeur n’est pas destiné à être utilisé à proximité du corps humain. L’appareil

devrait être monté de façon à ce que les antennes soient à au moins 20 cm (8 po) de toute personne.

Warning: Explosion hazard. Do not connect or disconnect while the circuit is live or unless the area

is free of ignitable concentrations.

Avertissement: Risque d'explosion. Ne pas connecter ou deconnecter le circuit est sous tension ou à

moins que la zone ne présente aucune concentration inflammable.

Warning: Do not use the USB connector unless the area is free of ignitable concentrations.

Avertissement: N'utilisez pas le connecteur USB à moins que la zone ne soit exempte de

concentrations inflammables.

Warning: Do not use the reset button unless the area is free of ignitable concentrations.

Avertissement: N'utilisez pas le bouton de réinitialisation à moins que la zone ne soit exempte de

concentrations inflammables.

RF Exposure

In accordance with FCC/IC requirements of human exposure to radio frequency fields, the radiating

element shall be installed such that a minimum separation distance of 20 cm should be maintained

from the antenna and the user's body.

Conformément aux exigences de la FCC/IC relatives à l’exposition humaine aux champs de

radiofréquences, l’élément de rayonnement doit être installé de manière à ce qu’une distance de

séparation minimale de 20 cm soit maintenue par rapport à l’antenne et au corps de l’utilisateur.

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS

GUIDE ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,

INFORMATION, AND RECOMMENDATIONS IN THIS GUIDE ARE BELIEVED TO BE

ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR

IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF

ANY PRODUCTS.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses,

and can radiate radio-frequency energy and, if not installed and used in accordance with this hardware guide

may cause harmful interference to radio communications.

Modifications to this product not authorized by Perle could void the FCC approval and negate your authority to

operate the product.

Perle reserves the right to make changes without further notice, to any products to improve reliability, function,

or design.

Perle, the Perle logo, and

IRG552x Series of Routers are trademarks of Perle.

60 Renfrew Drive, Markham, Ontario, L3R 0E1, Canada

from Perle.

VII

Perle IRG5520/5520+/5521/5521+ Series Router Hardware Installation Guide

Preface

Publishing History

Date Revision Update Details

Jan 2020 A.01.24.2020 Initial release of the Perle IRG552x Series Router

Hardware Installation Guide.

Table Of Contents

Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

What’s Included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

What You Need to Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SIM Card/s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Antenna/s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

USB-C Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Ethernet LAN Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Ethernet Link Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

GNSS Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Connecting the Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

AUX/IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Relay Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Inserting the SIM card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Connecting the Antenna/s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Connecting to the Ethernet Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Connecting to the Serial Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Connecting to the USB-C port in Console Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Connecting to the USB-C port as an Ethernet over USB Port. . . . . . . . . . . . . . . . . . 12

Connecting the Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Reset / Factory Default / Safe Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Fast Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Managing the IRG552x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Power Saving Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Low Voltage Standby. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Overheat Standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

IRG552x Deployment Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Fixed Installation without I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Recommended Vehicle Installation (Ignition Mode). . . . . . . . . . . . . . . . . . . . . . . . . 21

Fixed Installation with Analog Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

I/O Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Pulse Counter / Digital Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

High Side Pull-up / Dry Contact Switch Input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Digital Output / Low Side Current Sink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Digital Output/Open Drain. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

AUX /I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Pulse Counter / Digital Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

High Side Pull-up / Dry Contact Switch Input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Relay Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Appendix A - Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Appendix B - Label (sample) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Appendix C - Mounting the IRG552x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Flat surface mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

DIN Rail installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Appendix D - Mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Appendix E - Maintaining and Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Perle IRG5520/5520+/5521/5521+ Series Router Hardware Installation Guide

Overview

The PerleIRG5520/5520+/5521/5521+ routers are generically referred to as the IRG552x in this

guide. The IRG552x router is a compact, rugged, fully featured communications platform for real-

time wireless capabilities. It has multiple communication ports including serial, Ethernet, and a USB

port that can be used as a console port or as an additional Ethernet port. It supports LTE/4G wireless

solutions for both fixed and mobile applications (IoT). The IRG5520/5521LTE/4G supports Cat-6

technology with peak download rates of 300 Mbps and uploads speeds of 50 Mbps. They support

North American and EMEA frequency bands with automatic fall-back to 3G (HSPA+,UMTS) net-

works and integrated GNSS receiver (GPS, GLONASS, Beidou, and Galileo) satellite support. The

IRG5520+/5521+ offers global coverage of frequency bands, supports Cat-12 technology with auto-

matic fall-back to 3G (HSPA+,UMTS) networks. Download speeds of 600Mbps and uploads speeds

of 150 Mbps. The IRG5520+/5521+ also includes integrated GNSS receiver (GPS, GLONASS, Bei-

dou and Galileo) satellite support.

Application uses:

• Remotely monitoring and controlling equipment on pipelines, meters, pumps and valves in

any energy, utility, or industrial application

• Tracking the location of heavy equipment and assets in the field

• Providing reliable Internet access to a mobile workforce

What’s Included

The following components are included with your product:

• The router

• 2 wireless antennas (depending on model)

• 2 LTE antennas (depending on model)

• 2 WiFi antennas (depending on model)

• DC Power cable – pigtail (depending on model)

• 12VDC/2A power supply (depending on model)

• Enclosure mounting screws

• Quick Start Guide

• Optional – GPS passive or active antenna (order-able from Perle)

• Optional – DIN Rail mounting kit (order-able from Perle)

What You Need to Supply

Before you can begin, you need to have the following:

• A SIM card/s (provided by your mobile network operator)

• #1 Phillips screwdriver (if you are installing the SIM card)

• Computer or laptop computer with Ethernet interface and cable

• An Ethernet CAT5e or CAT6 10/100/1000BASE-T cable/to connect the

router to the network

Perle IRG5520/5520+/5521/5521+ Series Router Hardware Installation Guide

Hardware

Front View

LEDs

Power LED Normal Mode Power Saving Mode Special Notes

Off Router powered off Router powered off

Green-Solid Normal operating mode N/A

Green - Blip N/A Normal operating mode

Green - Flashing Booted - No configuration N/A

Amber - Blip Standby mode Standby mode Blips every 5 seconds

Amber - Flashing Router booting Router booting

Red - Blip Overheat standby Overheat standby

Red - Solid Hardware error Hardware error

Perle IRG5520/5520+/5521/5521+ Series Router Hardware Installation Guide

Hardware

Serial LED Normal Mode Power Saving Mode Special Notes

Off Disabled or not in use Always off

Green - Flashing Serial port Tx/Rx N/A

WWAN Normal Mode Power Saving Mode Special Notes

Off Disabled Disabled

Solid Connected Connected - Turns off

after 5 seconds

Green = Good signal

Amber = Fair signal

Red = Poor signal

Flashing Connection in progress N/A Same as above

Blip Not connected Not connected Same as above

WLAN Normal Mode Power Saving Mode Special Notes

Off Client mode - No

connection

AP mode - Not enabled

N/A

Green-Solid Client mode - Connected,

5GHz

AP mode - AP Active, 5GHz

N/A

Green - Flashing Client mode - Tx/Rx, 5GHz

AP mode - Tx/Rx, 5GHz

N/A

Amber - Solid Client mode - Connected,

2.4GHz

AP mode - AP Active,

2.4GHz

N/A

Amber - Flashing Client mode - Tx/Rx,

2.4GHz

AP mode - Tx/Rx, 2.4GHz

N/A

Perle IRG5520/5520+/5521/5521+ Series Router Hardware Installation Guide

Hardware

GNSS Normal Mode Power Saving Mode Special Notes

Off Disabled Disabled

Green-Solid Location Fix Location Fix - Turns off

after 5 seconds

Green - Blip Initializing off

Amber - Flashing No Fix N/A

Amber - Blip N/A No Fix

VPN Normal Mode Power Saving Mode Special Notes

Off No VPN No VPN

Green-Solid VPN connected. VPN connected - Turns

off after 5 seconds

Green - Flashing VPN connecting N/A

Red - Flashing VPN failed N/A

Internet Normal Mode Power Saving Mode Special Notes

Off Disabled Disabled

Green-Solid Internet/WAN connection Internet/WAN

connection - Turns off

after 5 seconds

Green - Blip Not connected N/A

Amber - Solid Backup mode N/A

Red - Solid Connection failed N/A

Red - Blip N/A Connection failed

Perle IRG5520/5520+/5521/5521+ Series Router Hardware Installation Guide

Hardware

SIM Card/s

The IRG552x supports two SIM cards. See Inserting the SIM card for the installation procedure.

SIM/s Interface 1.8V/3V

Back View

IRG5521/5521+

Note: IRG5520 models do not have the WLAN-1 and WLAN-2 antennas.

Antenna/s

The IRG5520 has three SMA antenna connectors Main, Diversity and GNSS. WiFi models have the

additional WLAN-1 and WLAN-2 connectors or the WiFi antennas. For more information on con-

necting the antennas see Connecting the Antenna/s. For more information on recommended LTE

Antenna specifications see Antenna/s

USB-C Port

The IRG552x USB port can increase the methods by which data can be sent and received from a con-

nected computer. The USB port can be set as a Ethernet over USB port or as a console port.

Perle IRG5520/5520+/5521/5521+ Series Router Hardware Installation Guide

Hardware

See Connecting to the USB-C port in Console Mode and Connecting to the USB-C port as an Ether-

net over USB Port.

Ethernet LAN Port

Once the port has connected and the link is established, the speed LED will turn on. The LED will

indicate whether you have a 10, 100 or 1000 Mbps link on the Ethernet port.

Ethernet Link Status

GNSS Connector

GPS+GLONAS+GAILILEO+BD

Passive Antenna – SMA(M) straight connector

See GNSS Technical Specifications for electrical details.

Link/Speed Indicator Description

Left LED Green Link + Flashing with activity 1000 Mbps

Both LEDs Link + Flashing with activity 100 Mbps

Right LED Green Link + Flashing with activity 10 Mbps

Off Off No LAN connected

Perle IRG5520/5520+/5521/5521+ Series Router Hardware Installation Guide

Hardware

Connecting the Power

Models can be shipped with a DC power cable or a pigtail cable depending on the model.

One GPIO configurable as high side pull-up / dry contact digital input, analog input, low side current

sink output, digital output/open drain, or pulse counter. One IGN configurable as vehicle ignition

sense or analog input.

Warning: Before servicing this product ensure the power source has been disconnected.

Pin Name Associated DC

Cable Wire color

Description Type

1 Power Red Main power supply for device

Note: If you want to turn the IRG552x on/off

using a control line, such as a vehicle ignition

line, we recommend that you connect the

control/ignition line to Pin 3 and apply

continuous power On Pin 1

PWR

2 Ground Black Main device ground

3 IGN White Connect to the vehicle ignition or an external

switch. This input can be configured to put

the router into a standby mode when the

signal goes low and take it out of standby

mode when it goes high. Alternatively it can

be used simply as an analog input.

4 GPIO Green User configurable digital input/output or

analog voltage sensing input. Connect to

switch, relay or external device.

Note:

Use copper conductors only.

Perle IRG5520/5520+/5521/5521+ Series Router Hardware Installation Guide

Hardware

AUX/IO

Two inputs configurable as high side pull-ups/digital inputs or pulse counters. One normally open

(NO) relay contact.

For application examples see --> AUX /I/O

Relay Alarm

The Router has one Normally Open (N0) relay (Pin 5 and Pin 1) switch. The relay switch can be con-

nected to an external powered device such as a siren or light for visual or audible notification of an

alarm status.

Ensure the power source is off prior to connection.

For application example see --> Relay Alarm

Pins 8 7 6 5

RS485 - GND Input B Relay NO

(normally open)

Pins 4 3 2 1

RS485 + GND Input A Relay NO

(normally open)

Warning: Before connecting wiring, ensure the power source has been disconnected.

Perle IRG5520/5520+/5521/5521+ Series Router Hardware Installation Guide

Installation

The steps for a typical installation are:

1. Inserting the SIM card/s. See Inserting the SIM card

2. Connecting the antenna/s. See

3. Connecting the Ethernet Port. See Ethernet LAN Port

4. Connecting the Serial Port. See Connecting to the Serial Port

5. Connecting to the Console Port in Console Mode. See Connecting to the USB-C port in Console

Mode

6. Using the Console port as a virtual Ethernet port. See Connecting to the USB-C port as an Ether-

net over USB Port

7. Connecting the power. See Connecting the Power

8. Logging into the IRG552x See Fast Setup or Connecting to the USB-C port in Console Mode

9. Optional DIN Rail mounting. See Appendix C - Mounting the IRG552x

Inserting the SIM card

The IRG552x comes with two 6-pin SIM sockets for mini-SIM (2FF) cards.

Ensure the power is disconnected before you insert the SIM card/s.

1. Using your Phillips screwdriver, removed the two screws from the panel covering the SIM slots.

Gently pry the cover loose from the opening.

2. Align the SIM card so that the SIM card will slide into the top slot (slot#1). Each SIM card has a

notched corner for orientation and the SIM card can only be inserted the correct way. You will

hear an audible click when the SIM is inserted correctly. Always populate slot#1 first. Add a sec-

ond SIM card if your network setup requires it.

3. Align the SIM cover plate and secure the plate with the screws.

Note:

Do not force the SIM(s) card in or you may damage the card or your IRG552x router.

Perle IRG5520/5520+/5521/5521+ Series Router Hardware Installation Guide

Installation

Connecting the Antenna/s

The IRG552x has three SMA female antenna connectors:

• Main Cellular antenna connector

• Rx Diversity antenna connector

• GNSS antenna connector

WiFi models (IRG5521/5521+) have an additional two SMA male antenna connectors:

• WLAN-1

• WLAN-2

1. Connect your cellular antenna to the SMA cellular antenna connector labeled Main

2. Connect your GPS antenna to the SMA GPS antenna connector labeled GNSS.

3. Mount the GPS antenna where it has a good view of the sky (at least

90⁰).

4. Connect the diversity antenna to the SMA diversity antenna labeled Diversity

5. For IRG5521/5521+ models, connect the WLAN antennas to WLAN-1 and WLAN-2.

Connecting to the Ethernet Port

The Ethernet RJ45 port provides the standard Ethernet interface speeds of 10/100/1000 Mbps through

twisted pair (UTP) cables of up to 100 meters (328ft) in length. Cat5e or Cat6 cables are

recommended for 1000 Mbps connections.

Warning: For Zone 2 and/or Class I, Division 2 hazardous location applications. Antennas intended for use with

the product must be installed within the end use enclosure. For remote mounting of the antennas in unclassified

or classified locations, routing and installation of the antennas shall be in accordance with the appropriate

location regulations.

Note:

When attaching the antennas to the SMA connectors hand tighten only (do not use tools to tighten

(maximum torque is 7Kgf-cm/1.1 N-m(10 in-lb).

La page charge ...

Perle IRG5520 LTE Guide d'installation

Marque: Perle

Modèle: IRG5520 LTE

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Perle IRG5520 LTE Installation guide

Perle IRG5520 LTE Guide d'installation

Perle IRG5520 LTE Guide d'installation

dans d''autres langues

Documents connexes

Autres documents