Wacker Neuson E3000 Manuel utilisateur

Operator’s manual

Hydronic Surface Heater

E3000

Machine Type E3000

Material number

5100059254

Version

01

Date 08/2020

Language

[en-fr]

5100059254

Imprint

Publisher and copyright holder:

WackerNeusonCorporation

N92W15000 Anthony Ave, Menomonee Falls, WI

53051, USA

www.wackerneuson.us

Original operator’s manual

worldwide.

This document may be used by the recipient only for the designated purpose. It may in no way be duplicated or

translated in any other language, in whole or in part, without prior permission in writing from the manufacturer.

Reproduction or translation of this publication, in whole or part, is not permitted without the written consent of

Wacker Neuson Corporation.

Violations of legal regulations, in particular of the copyright protection, will be subject to civil and criminal prosecu-

tion.

Wacker Neuson Corporation reserves the right to change its products and their technical specifications for further

technical development at any time without any claim to changes to machines already delivered. The information in

the technical documentation supplied with the product applies in each case.

The machine on the cover is for illustration purposes only and may therefore have special equipment (options).

Wacker Neuson Corporation, responsibility for errors or omissions not accepted, printed in USA

California Proposition 65 Warning



iii

[us] | 08/2020 | 5100059253 | E3000 | Operator’s manual

California Proposition 65 Warning

WARNING

The engine exhaust from this product contains chemicals known to the State

of California to cause cancer, birth defects, or other reproductive harm.

WARNING

Diesel engine exhaust and some of its constituents are known to the State of

California to cause cancer, birth defects, and other reproductive harm.

WARNING

Cancer and Reproductive Harm -

www.P65Warnings.ca.gov.

WARNING

Batteries, battery posts, terminals and related accessories contain lead and

lead compounds, and other chemicals known to the State of California to

cause cancer and birth defects or other reproductive harm. WASH HANDS

AFTER HANDLING.

Table of Contents

iv

Operator’s manual | | 5100059253 | 08/2020 | [us]

Table of Contents

California Proposition 65 Warning

1 Preface

1.1 Introduction .......................................................................................................................................... 10

1.2 Storage location of the operator's manual ........................................................................................... 10

1.3 Accident prevention regulations........................................................................................................... 10

1.4 Wacker Neuson Contact...................................................................................................................... 10

1.5 Use of the Operator's Manual .............................................................................................................. 11

2 Usage

2.1 Intended Use ....................................................................................................................................... 14

2.2 Unintended Use ................................................................................................................................... 14

2.3 Residual Risks ..................................................................................................................................... 15

3 Safety

3.1 Signal Words Used in this Manual....................................................................................................... 16

3.2 Safety Guidelines for Operating the Machine ...................................................................................... 17

3.3 Safety Guidelines for Lifting the Machine ............................................................................................ 19

3.4 Safety Guidelines for Operating Generators........................................................................................ 20

3.5 Service Safety...................................................................................................................................... 22

3.6 Safety Guidlines for Towing the Machine ............................................................................................ 23

3.7 Reporting Safety Defects..................................................................................................................... 24

4 Description of the Machine

4.1 Machine Description ............................................................................................................................ 25

4.2 Overview of the Labels ........................................................................................................................ 26

4.3 Safety Label Meanings ........................................................................................................................ 29

4.4 Information Label Meanings ................................................................................................................ 34

5 Transportation

5.1 Lifting the Machine............................................................................................................................... 39

5.2 Preparing the Machine for Transport on a Truck or Trailer.................................................................. 39

5.3 Transporting the Machine on a Truck or Trailer................................................................................... 41

5.4 Before Towing Checklist ...................................................................................................................... 43

5.5 Towing the Machine............................................................................................................................. 44

5.6 Testing the Breakaway System—Electric Brakes................................................................................ 45

5.7 Hazardous Materials Placards............................................................................................................. 47

6 Commissioning

6.1 Preparing the Machine for First Use .................................................................................................... 48

6.2 Refueling the Machine ......................................................................................................................... 48

6.3 Positioning the Machine for Outdoor Use ............................................................................................ 49

6.4 Setting Up the Burner—Diesel............................................................................................................. 51

Table of Contents

v

[us] | 08/2020 | 5100059253 | E3000 | Operator’s manual

6.5 Setting and Checking the Electrodes................................................................................................... 53

6.6 Replacing the Burner Nozzle ............................................................................................................... 55

6.7 Setting the "Z" Distance ....................................................................................................................... 57

6.8 Adjusting the Air Settings..................................................................................................................... 58

6.9 Adjusting the Fuel Pressure................................................................................................................. 59

6.10 Factory Settings—Gas......................................................................................................................... 60

6.11 Restrictions for Connecting the Gas Supply ........................................................................................ 60

6.12 Setting Up the Burner—Gas ................................................................................................................ 61

6.13 Removing the Combustion Head......................................................................................................... 63

6.14 Adjusting the Ionization Probe and the Electrode................................................................................ 65

6.15 Changing the Burner Orifice ................................................................................................................ 66

6.16 Changing the Burner Diaphragm ......................................................................................................... 66

6.17 Checking the Burner Air Damper Setting............................................................................................. 68

6.18 Adjusting the Head Setting .................................................................................................................. 68

6.19 Checking the Supply Gas Pressure..................................................................................................... 70

6.20 Checking and Adjusting the Burner Gas Pressure .............................................................................. 71

7 Operation

7.1 External Components .......................................................................................................................... 73

7.2 Internal Components ........................................................................................................................... 74

7.3 Rear Components................................................................................................................................ 75

7.4 Pumps, Gauges, and Valves ............................................................................................................... 76

7.5 Control Panel ....................................................................................................................................... 77

7.6 Control Panel Components.................................................................................................................. 77

7.7 Breaking in the Generator.................................................................................................................... 78

7.8 Checking the Heat Transfer Fluid (HTF) Level .................................................................................... 78

7.9 Recommended Fuels and Fuel Blending Guide .................................................................................. 79

7.10 Before Starting Checks........................................................................................................................ 80

7.11 Starting, Operating, Stopping the Machine—Kohler............................................................................ 82

7.12 Preheating the Heat Transfer Fluid (HTF) ........................................................................................... 84

7.13 Initiating Heat Transfer Fluid (HTF) Flow............................................................................................. 85

7.14 Setting the Operating Temperature ..................................................................................................... 87

7.15 Unwinding and Positioning the Hoses ................................................................................................. 87

7.16 Hose Spacing Guidelines .................................................................................................................... 88

7.17 Monitoring the Operating Parameters.................................................................................................. 89

7.18 Rewinding the Hoses........................................................................................................................... 90

7.19 Resetting a Low HTF Fault .................................................................................................................. 92

7.20 Using the Quick-Connect Coupling...................................................................................................... 96

7.21 Operating States of the Beckett Burner Controller .............................................................................. 97

8 Accessories

8.1 Available Accessories........................................................................................................................ 101

Table of Contents

vi

Operator’s manual | | 5100059253 | 08/2020 | [us]

8.2 Expanding the Surface Heating Capacity .......................................................................................... 102

8.3 Expanded Operation Using One HHS3002 and One DPP ................................................................ 103

8.4 Expanded Operation Using Two HHS3002 and Two DPP ................................................................ 105

8.5 Mounting and Connecting the Auxiliary Pump Panel......................................................................... 108

8.6 Using Heat Exchangers to Heat Air ................................................................................................... 110

8.7 Connecting Six HX50 Heat Exchangers ............................................................................................ 111

8.8 Connecting Five HX50 Heat Exchangers .......................................................................................... 114

8.9 Connecting Four HX50 Heat Exchangers.......................................................................................... 117

8.10 Connecting Three HX50 Heat Exchangers........................................................................................ 119

8.11 Connecting Two HX50 Heat Exchangers .......................................................................................... 120

8.12 Connecting One HX50 Heat Exchanger ............................................................................................ 122

8.13 Connecting Three HX100 Heat Exchangers...................................................................................... 125

8.14 Connecting Two HX100 Heat Exchangers ........................................................................................ 127

8.15 Connecting One HX100 Heat Exchanger .......................................................................................... 129

8.16 Connecting Two HX200 Heat Exchangers ........................................................................................ 132

8.17 Connecting One HX200 Heat Exchanger .......................................................................................... 134

9 Maintenance

9.1 Maintenance Schedule ...................................................................................................................... 137

9.2 Cleaning the Quick-Connect Couplings............................................................................................. 137

9.3 Inspecting the HTF System and the Fuel System ............................................................................. 137

9.4 Repairing a Hose ............................................................................................................................... 138

9.5 Checking the Heat Transfer Fluid (HTF) Level .................................................................................. 140

9.6 Inspecting the Electrical Components ............................................................................................... 140

9.7 Testing the Trailer Breakaway System .............................................................................................. 142

9.8 Filling the HTF Expansion Tank......................................................................................................... 142

9.9 Cleaning the HTF Strainer ................................................................................................................. 143

9.10 Replacing the Fuel Filter.................................................................................................................... 145

9.11 Lubricating the Hose Reel System .................................................................................................... 146

9.12 Cleaning the Turbulators and the Exhaust Ducting ........................................................................... 147

9.13 Inspecting and Replacing the Rope Gasket ...................................................................................... 149

9.14 Checking and Adjusting the Burner Air Settings................................................................................ 150

9.15 Checking and Adjusting the Fuel Pressure........................................................................................ 151

9.16 Checking and Adjusting the Electrodes ............................................................................................. 151

9.17 Replacing the Burner Nozzle ............................................................................................................. 151

9.18 Removing the Oil Burner ................................................................................................................... 151

9.19 Installing the Burner........................................................................................................................... 152

9.20 Storing the Machine........................................................................................................................... 153

9.21 Storing the Generator ........................................................................................................................ 154

9.22 Preparing the Machine for Seasonal Operation................................................................................. 154

9.23 Connecting and Maintaining the Battery............................................................................................ 155

Table of Contents

vii

[us] | 08/2020 | 5100059253 | E3000 | Operator’s manual

9.24 Machine Disposal and Decommissioning .......................................................................................... 156

9.25 Engine Maintenance: Kohler 1003..................................................................................................... 157

9.26 Changing the Oil and Filter ................................................................................................................ 159

9.27 Generator Load Banking Procedure .................................................................................................. 161

10 Malfunctions

10.1 Troubleshooting the Machine ............................................................................................................ 163

10.2 Troubleshooting the Oil Burner.......................................................................................................... 164

10.3 Troubleshooting the Gas Burner........................................................................................................ 164

10.4 General Troubleshooting ................................................................................................................... 165

11 Technical Data

11.1 Engine—Kohler.................................................................................................................................. 167

11.2 Machine ............................................................................................................................................. 167

11.3 Trailer................................................................................................................................................. 168

11.4 Dimensions ........................................................................................................................................ 168

12 MSDS: Dowfrost™ HD 50

13 Fuji Temperature Controller

13.1 Fuji Temperature Controller Hysteresis (differential) Adjusting ......................................................... 176

13.2 Fuji Temperature Controller Low Temperature Limit Adjusting ......................................................... 177

13.3 Fuji Temperature Controller High Temperature Limit Adjusting ........................................................ 178

14 Tire Safety Information

14.1 Tire Safety Information ...................................................................................................................... 179

14.2 Tire Safety Information Section Descriptions..................................................................................... 179

14.3 Steps for Determining Correct Load Limit—Trailer............................................................................ 180

14.4 Steps for Determining Correct Load Limit—Tow Vehicle .................................................................. 182

14.5 Glossary of Tire Terminology............................................................................................................. 182

14.6 Tire Safety—Everything Rides on It................................................................................................... 187

14.7 Safety First—Basic Tire Maintenance ............................................................................................... 187

14.8 Tire Safety Tips.................................................................................................................................. 194

15 Schematics

15.1 Composite Schematic—Machine with Oil Burner .............................................................................. 196

15.2 Composite Schematic—Machine with Gas Burner............................................................................ 198

15.3 Circulation System Circuit.................................................................................................................. 200

15.4 Rewind System Circuit....................................................................................................................... 202

15.5 Generator—AC Schematic ................................................................................................................ 204

15.6 Generator—DC Schematic ................................................................................................................ 206

15.7 Gas Train Schematic ......................................................................................................................... 208

15.8 Trailer Plug—Wiring Diagram ............................................................................................................ 209

15.9 Trailer Lights and Brakes—Wiring Diagram ...................................................................................... 210

Table of Contents

viii

Operator’s manual | | 5100059253 | 08/2020 | [us]

15.10 Trailer Lights and Brakes—Components........................................................................................... 211

15.11 Trailer Junction Box—Wiring Diagram............................................................................................... 212

Index ..............................................................................................................................................................213

Table of Contents

ix

[us] | 08/2020 | 5100059253 | E3000 | Operator’s manual

Preface

1.1 Introduction

10

Operator’s manual | E3000 | 5100059253 | 08/2020 | [us]

1 Preface

1.1 Introduction

This operator’s manual contains important information and procedures for

the safe, proper and economical operation of this Wacker Neuson machine.

Carefully reading, understanding and observing it helps to avoid dangers, re-

duce repair costs and downtimes and thus increase the availability and ser-

vice life of the machine.

This operator’s manual is not a manual for extensive maintenance or repair

work. Such work must be carried out by Wacker Neuson Service or by tech-

nically trained personnel. The Wacker Neuson machine must be operated

and maintained in accordance with the instructions in this operator’s manual.

Improper operation or maintenance can cause hazards.

Defective machine parts must be replaced immediately.

Wacker Neuson contact persons are always available to answer questions

about operation or maintenance.

1.2 Storage location of the operator's manual

This operator's manual must be kept in the immediate vicinity of the machine

and accessible to personnel at all times.

If this operator's manual is lost or you require a new copy, there are two

ways of obtaining a replacement:

• You can download it from the Internet - http://www.wackerneuson.com

• Or you can contact your Wacker Neuson representative.

1.3 Accident prevention regulations

In addition to the notes and safety instructions in this operator’s manual, the

local accident prevention regulations and the national industrial safety regu-

lations apply.

1.4 Wacker Neuson Contact

Depending on the country, the Wacker Neuson contact is a Wacker Neuson

Service, a Wacker Neuson subsidiary or a Wacker Neuson dealer.

On the Internet at - http://www.wackerneuson.com.

Preface

Use of the Operator's Manual 1.5

11

[us] | 08/2020 | 5100059253 | E3000 | Operator’s manual

1.5 Use of the Operator's Manual

WARNING

Risk of personal injury or machine damage from improper use

► Before using the machine, read and understand all instructions and fol-

low them carefully.

► The manufacturer is not responsible for damages to goods or persons

due to improper use of this machine.

WARNING

Failure to comply with the precautions and instructions provided with this

machine can result in death, serious injury, and property loss or damage

from fire, explosion, burns, asphyxiation, carbon monoxide poisoning, and/or

electric shock.

► Before using the machine, read and understand all precautions and in-

structions that have been provided. Follow them carefully.

► Only persons who can understand and follow the precautions and in-

structions should use or service this machine.

► Contact the manufacturer if you need assistance with operating the ma-

chine or need replacement manuals or labels.

WARNING

Work site fire, burn, inhalation, and explosion hazards

► This machine is not designed to be used in explosion-proof applications.

Keep solid combustibles, such as building materials, paper, or card-

board at a safe distance away from the machine.

► Never use this machine in applications which do or may contain volatile

or airborne combustibles (e.g natural gas fumes), or products such as

gasoline, solvents, paint thinner, dust particles, or unknown chemicals.

WARNING

Not for use in homes or recreational vehicles. Installing this machine in a

home or RV may result in fire, explosion, property damage, personal injury,

or death.

► Operate the machine only as specified in the topic Machine Description

and Intended Use.

This operator’s manual must be regarded as an integral part of the machine

and must be kept in a safe place throughout its service life. This operator’s

manual must be passed on to each subsequent owner or user of this ma-

chine.

1

Preface

1.5 Use of the Operator's Manual

12

Operator’s manual | E3000 | 5100059253 | 08/2020 | [us]

This operator’s manual apply to various machine types from one product

range. For this reason, some illustrations may differ from the appearance of

the purchased machine. Variant-dependent components that are not in-

cluded in the scope of delivery can also be described.

The information contained in this operator’s manual is based on machines

manufactured up to the time it was printed. Wacker Neuson reserves the

right to make changes to this information without notice.

It must be ensured that any changes or additions made by the manufacturer

are immediately incorporated into this operator’s manual.

The following machines and variants/options are described:

Machine Item Number

E3000 5100055568, 5100055569, 5100056440,

5100056441

Machine identification

A nameplate listing the model number, item number, revision, and serial

number is attached to this machine. The location of the nameplate is shown

below.

Fig.1: Nameplate location

Serial number (S/N)

For future reference, record the serial number in the space provided below.

You will need the serial number when requesting parts or service for this ma-

chine.

Serial number:

Preface

Use of the Operator's Manual 1.5

13

[us] | 08/2020 | 5100059253 | E3000 | Operator’s manual

Machine documentation

• From this point forward in this documentation, Wacker Neuson Produc-

tion Americas LLC will be referred to as Wacker Neuson.

• For spare parts information, please see your Wacker Neuson dealer, or

visit the Wacker Neuson website at http://www.wackerneuson.com/.

• When ordering parts or requesting service information, be prepared to

provide the machine model number, item number, revision number, and

serial number.

NOTICE

State Health Safety Codes and Public Resources Codes specify that in cer-

tain locations spark arresters be used on internal combustion engines that

use hydrocarbon fuels. A spark arrester is a device designed to prevent acci-

dental discharge of sparks or flames from the engine exhaust. Spark ar-

resters are qualified and rated by the United States Forest Service for this

purpose. In order to comply with local laws regarding spark arresters, consult

the engine distributor or the local Health and Safety Administrator.

Manufacturer’s approval

This manual contains references to approved parts, attachments, and modi-

fications. The following definitions apply:

• Approved parts or attachments are those either manufactured or pro-

vided by Wacker Neuson.

• Approved modifications are those performed by an authorized Wacker

Neuson service center according to written instructions published by

Wacker Neuson.

• Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following

consequences:

• Serious injury hazards to the operator and persons in the work area

• Permanent damage to the machine, which will not be covered under

warranty

Contact your Wacker Neuson dealer immediately if you have questions

about approved or unapproved parts, attachments, or modifications.

1

Usage

2.1 Intended Use

14

Operator’s manual | E3000 | 5100059253 | 08/2020 | [us]

2 Usage

2.1 Intended Use

This machine is intended to be used as a surface heater in order to thaw

frozen ground, to cure concrete, or to prevent frost and freezing. In addition,

when used with other Wacker Neuson accessories, this machine can be

used to heat air.

2.2 Unintended Use

This machine has been designed and built strictly for the intended use de-

scribed above. Using the machine for any other purpose could permanently

damage the machine or seriously injure the operator or other persons in the

area. Machine damage caused by misuse is not covered under warranty.

The following are some examples of misuse:

This machine has been designed and built strictly for the intended use(s) de-

scribed above. Using the machine for any other purpose could permanently

damage the machine or seriously injure the operator or other persons in the

area. Machine damage caused by misuse is not covered under warranty.

The following are some examples of misuse:

• Using the machine to heat anything other than what is stated above

• Using the machine to pump anything other than the factory recom-

mended heat transfer fluid (HTF)

• Using the generator (if equipped) to power anything other than the ma-

chine itself or Wacker Neuson accessory machines, as instructed in the

Operator's Manual

• Operating the generator (if equipped) in a manner that is inconsistent

with all federal, state, and local codes and regulations

• Using the machine as a ladder, support, or work surface

• Using the machine to carry or transport passengers or equipment

• Using the machine to tow other machines

• Operating the machine outside of factory specifications

• Operating the machine in a manner inconsistent with all warnings found

on the machine and in the Operator’s Manual

Usage

Residual Risks 2.3

15

[us] | 08/2020 | 5100059253 | E3000 | Operator’s manual

2.3 Residual Risks

This machine has been designed and built in accordance with the latest

global safety standards. It has been carefully engineered to eliminate haz-

ards as far as practicable and to increase operator safety through protective

guards and labeling.

However, some risks may remain even after protective measures have been

taken. They are called residual risks. On this machine, they may include ex-

posure to:

• Heat, noise, exhaust, and carbon monoxide from the engine

• Heat, noise, and exhaust from the engine or hydronic heater

• Burns from the HTF or radiant heat from the hoses

• Fire hazards from improper refueling techniques

• Tripping hazards from the hoses

• Fire hazards from improper refueling techniques

• Fuel and its fumes

• Electric shock and arc flash

• Personal injury from improper lifting the trailer tongue

• Typical hazards related to towing a trailer on roads and highways

To protect yourself and others, make sure you thoroughly read and under-

stand the safety information presented in this manual before operating the

machine.

2

Safety

3.1 Signal Words Used in this Manual

16

Operator’s manual | E3000 | 5100059253 | 08/2020 | [us]

3 Safety

3.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and

NOTE signal words which must be followed to reduce the possibility of per-

sonal injury, damage to the equipment, or improper service.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will re-

sult in death or serious injury.

► To avoid death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

► To avoid possible death or serious injury from this type of hazard, obey

all safety messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could

result in minor or moderate injury.

► To avoid possible minor or moderate injury from this type of hazard,

obey all safety messages that follow this signal word.

NOTICE

NOTICE identifies a situation that causes damage if it is not observed.

► To avoid possible damage from this type of hazard, obey all safety mes-

sages that follow this signal word.

Note: A Note contains additional information important to a procedure.

Safety

Safety Guidelines for Operating the Machine 3.2

17

[us] | 08/2020 | 5100059253 | E3000 | Operator’s manual

3.2 Safety Guidelines for Operating the Machine

Operator and service training, knowledge, and qualifications

Before operating the machine:

• Read and understand the operating instructions contained in all manuals

delivered with the machine.

• Always keep this Operator's Manual and other manuals that accompany

the machine stored with the machine and available for use. Immediately

replace an incomplete or illegible Operator's Manual.

• Familiarize yourself with the location and proper use of all controls and

safety devices.

• Know the rules for the job site.

• Contact Wacker Neuson for additional training if necessary.

When operating this machine:

• Do not allow improperly trained people to operate the machine.

• People operating the machine must be familiar with the potential risks

and hazards associated with it.

• Follow legal and other mandatory regulations relevant to accident pre-

vention and environmental protection. These may include handling haz-

ardous substances, issuing and/or wearing personal protective equip-

ment, or obeying traffic regulations.

The machine must not be accessed or operated by:

• Children

• People impaired by alcohol, drugs, or prescription drugs

Machine condition

Only operate the machine when:

• All safety devices and guards are in place and in working order.

• All controls operate correctly.

• The machine is set up correctly according to the instructions in the Oper-

ator’s Manual.

• The machine is clean, free of debris and combustible materials.

• The machine’s labels are legible.

When operating the machine:

• Do not modify or defeat the safety devices.

• Do not use worn electrical cords.

• Do not use faulty fuel supplies.

3

Safety

3.2 Safety Guidelines for Operating the Machine

18

Operator’s manual | E3000 | 5100059253 | 08/2020 | [us]

Safety devices, controls, and attachments

Only operate the machine when:

• All safety devices and guards are in place and in working order.

• All controls operate correctly.

• The machine is set up correctly according to the instructions in the Oper-

ator’s Manual.

• The machine is clean.

• The machine’s labels are legible.

To ensure safe operation of the machine:

• Do not operate the machine if any safety devices or guards are missing

or inoperative.

• Do not modify or defeat the safety devices.

• Only use accessories or attachments that are approved by Wacker Neu-

son.

Safe operating practices

When operating this machine:

• Remain aware of the machine’s moving parts. Keep hands, feet, and

loose clothing away from the machine’s moving parts.

• Wear protective clothing appropriate to the job site when operating the

machine.

• Wear safety glasses.

• Do not operate a machine in need of repair.

• Do not smoke near the machine.

• Do not consume the operating fluids used in this machine. Depending on

your machine model, these operating fluids may include water, wetting

agents, fuel (gasoline, diesel, kerosene, propane, or natural gas), oil,

coolant, hydraulic oil, heat transfer fluid (propylene glycol with additives),

battery acid, or grease.

Personal protective equipment (PPE)

Wear the following personal protective equipment (PPE) while operating,

servicing, or maintaining this machine:

• Close-fitting work clothes that do not hinder movement

• Safety glasses with side shields

• Hearing protection

• Safety-toed footwear

• Safety gloves

In addition, before servicing or maintaining the machine:

• Tie back long hair.

• Remove all jewelry (including rings).

Safety

Safety Guidelines for Lifting the Machine 3.3

19

[us] | 08/2020 | 5100059253 | E3000 | Operator’s manual

After use

• Stop the engine when the machine is not being operated.

• Close the fuel valve on engines equipped with one when the machine is

not being operated.

• Ensure that the machine will not tip over, roll, slide, or fall when not being

operated.

• Store the machine properly when it is not being used. The machine

should be stored in a clean location out of the reach of children.

Work space

When operating the machine:

• Position the machine on a firm, noncombustible, level surface, and chock

the wheels.

• Position the machine on the job site so that neither it nor the operator are

standing in water.

• Keep the area immediately surrounding and underneath the machine

clean, neat, and free of debris and combustible materials.

• Keep the area above the machine clear of debris that could fall on the

machine.

• Store the machine properly when it is not being used.

• Keep unauthorized personnel, children, and pets away from the ma-

chine.

When operating the machine:

• Never operate the machine in areas that contain flammable objects, fu-

els, or products that produce flammable vapors.

3.3 Safety Guidelines for Lifting the Machine

When lifting the machine:

• Make sure slings, chains, hooks, ramps, jacks, forklifts, cranes, hoists,

and any other type of lifting device used is attached securely and has

enough weightbearing capacity to lift or hold the machine safely. For ma-

chine weight, see Machine on page 167.

• Remain aware of the location of other people when lifting the machine.

• Only use the lifting points and tie-downs described in the Operator’s

Manual.

• Make sure the transporting vehicle has sufficient load capacity and plat-

form size to safely transport the machine.

To reduce the possibility of injury:

• Do not stand under the machine while it is being lifted or moved.

• Do not get onto the machine while it is being lifted or moved.

3

Safety

3.4 Safety Guidelines for Operating Generators

20

Operator’s manual | E3000 | 5100059253 | 08/2020 | [us]

3.4 Safety Guidelines for Operating Generators

DANGER

Carbon monoxide hazard

Using a generator indoors can kill you in minutes. Generator exhaust con-

tains carbon monoxide (CO). This is a poison you cannot see or smell. If you

can smell the generator exhaust, you are breathing CO. But even if you can-

not smell the exhaust, you could still be breathing CO.

WARNING

Electrocution hazard

Generators present special hazards during operation and servicing. These

include the risk of electrocution or severe electrical shock. Failure to follow

the safety information below can result in severe injury or death.

► Read and follow the safety instructions in this Operator’s Manual.

► Contact the generator manufacturer for additional information regarding

the generator.

WARNING

Internal combustion engines present special hazards during operation

and fueling.

Failure to follow the warnings and safety instructions could result in severe

injury or death.

► Read and follow the safety instructions in this Operator’s Manual.

► Contact the generator manufacturer for additional information regarding

the generator.

WARNING

Most used oil contains small amounts of materials that can cause cancer

and other health problems if inhaled, ingested, or left in contact with skin for

prolonged periods of time.

► Take steps to avoid inhaling or ingesting used engine oil.

► Wash skin thoroughly after exposure to used engine oil.

This machine is built with user safety in mind; however, like any electrical de-

vice it can present serious hazards if improperly operated and serviced. Fol-

low instructions carefully. Should questions arise during operation or service

of this equipment, contact your Wacker Neuson dealer.

La page est en cours de chargement...

Wacker Neuson E3000 Manuel utilisateur

Wacker Neuson E3000 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents