Pioneer GM-DX971 Le manuel du propriétaire

Marque: Pioneer

Modèle: GM-DX971

Catégorie: Amplificateurs audio de voiture

Taper: Le manuel du propriétaire

Ce manuel convient également à

PIONEER CORPORATION

28-8, Honkomagome 2-chome, Bunkyo-ku,

Tokyo 113-0021, JAPAN

PIONEER ELECTRONICS (USA) INC.

P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.

TEL: (800) 421-1404

PIONEER EUROPE NV

Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium/Belgique

TEL: (0) 3/570.05.11

PIONEER ELECTRONICS ASIACENTRE PTE. LTD.

2 Jalan Kilang Barat, #07-01, Singapore 159346

TEL: 65-6378-7888

PIONEER ELECTRONICS AUSTRALIA PTY. LTD.

5 Arco Lane, Heatherton, Victoria, 3202 Australia

TEL: (03) 9586-6300

PIONEER ELECTRONICS DE MÉXICO S.A. DE C.V.

Blvd.Manuel Ávila Camacho 138, 10 piso

Col.Lomas de Chapultepec, México, D.F. 11000

TEL: 52-55-9178-4270

FAX: 52-55-5202-3714

先鋒股份有限公司

台北市內湖區瑞光路407號8樓

電話： 886-(0)2-2657-3588

先鋒電子（香港）有限公司

香港九龍長沙灣道909號5樓

電話： 852-2848-6488

Tous droits de reproduction et de

traduction réservés.

<5707000012760V> UC

<5707000012760V>2

Thank you for purchasing this PIONEER

product

To ensure proper use, please read through this

manual before using this product. It is espe-

cially important that you read and observe

WARNINGs and CAUTIONs in this manual.

Please keep the manual in a safe and accessible

place for future reference.

Information to User

Alteration or modifications carried out without

appropriate authorization may invalidate the

user’s right to operate the equipment.

After-sales service for

Pioneer products

Please contact the dealer or distributor from

where you purchased this unit for after-sales

service (including warranty conditions) or any

other information. In case the necessary infor-

mation is not available, please contact the

companies listed below:

Please do not ship your unit to the companies

at the addresses listed below for repair without

advance contact.

USA&CANADA

Pioneer Electronics (USA) Inc.

CUSTOMER SUPPORT DIVISION

P.O. Box 1760

Long Beach, CA 90801-1760

800-421-1404

For warranty information please see the Lim-

ited Warranty sheet included with this unit.

If you experience problems

Should this product fail to operate properly,

please contact your dealer or nearest author-

ized Pioneer Service Station.

Visit our website

http://www.pioneerelectronics.com

in Canada

http://www.pioneerelectronics.ca

! Learn about product updates (such as firm-

ware updates) for your product.

! Register your product to receive notices

about product updates and to safeguard

purchase details in our files in the event of

loss or theft.

! Access owner’s manuals, spare parts infor-

mation, service information, and much

more.

The Safety of Your Ears is in

Your Hands

Get the most out of your equipment by playing

it at a safe level—a level that lets the sound

come through clearly without annoying blar-

ing or distortion and, most importantly, with-

out affecting your sensitive hearing. Sound

can be deceiving. Over time, your hearing

“comfort level” adapts to higher volumes of

sound, so what sounds “normal” can actually

be loud and harmful to your hearing. Guard

against this by setting your equipment at a

safe level BEFORE your hearing adapts.

ESTABLISH A SAFE LEVEL:

! Set your volume control at a low setting.

! Slowly increase the sound until you can

hear it comfortably and clearly, without dis-

tortion.

! Once you have established a comfortable

sound level, set the dial and leave it there.

<5707000012760V>3

Before you start

BE SURE TO OBSERVE THE FOLLOWING

GUIDELINES:

! Do not turn up the volume so high that you

can’t hear what’s around you.

! Use caution or temporarily discontinue use

in potentially hazardous situations.

! Do not use headphones while operating a

motorized vehicle; the use of headphones

may create a traffic hazard and is illegal in

many areas.

About This Product

This product is a mono amplifier for subwoofer. If

both L (left) and R (right) channels are connected

to the RCA input of this product, output is mixed

because this product is a mono amplifier.

Before connecting/

installing the amplifier

WARNING

! This product contains chemicals known to the

State of California and other governmental en-

tities tocause cancer and birth defects or

other reproductive harm. Wash hands after

handling.

! Slots and openings in the cabinet are provided

for ventilation to ensure reliable operation of

the product, and to protect it from overheat-

ing. To prevent fire hazard, the openings

should never be blocked or covered with items

(such as papers, floor mat, cloths).

! This unit is for vehicles with a 12 V battery and

negative grounding. Before installing in re-

creational vehicles, trucks or buses, check the

battery voltage.

! When installing this unit, make sure to con-

nect the ground wire first. Ensure that the

ground wire is properly connected to metal

parts of the car’s body. The ground wire of the

one of this unit must be connected to the car

separately with different screws. If the screw

for the ground wire loosens or falls out, it

could result in fire, generation of smoke or

malfunction.

! Be sure to install the fuse to the battery wire.

! Always use a fuse of the rating prescribed.

The use of an improper fuse could result in

overheating and smoke, damage to the pro-

duct and injury, including burns.

! Check the connections of the power supply

and speakers if the fuse of the separately sold

battery wire or the amplifier fuse blows. Deter-

mine and resolve the cause, then replace the

fuse with and identical equivalent.

! Always install the amplifier on a flat surface.

Do not install the amplifier on a surface that

is not flat or on a surface with a protrusion.

Doing so could result in malfunction.

! When installing the amplifier, do not allow

parts such as extra screws to get caught be-

tween the amplifier and the automobile.

Doing so could cause malfunction.

! Do not allow this unit to come into contact

with liquids. Electrical shock could result.

Also, damage to this unit, smoke, and over-

heating could result from contact with liquids.

The surfaces of the amplifier and any attached

speakers may also heat up and cause minor

burns.

! In the event of any abnormality, the power

supply to the amplifier is cut off to prevent

equipment malfunction. If this occurs, switch

the system power off and check the power

supply and speaker connections. If you are un-

able to determine the cause, please contact

your dealer.

! Always disconnect the negative * terminal of

the battery beforehand to avoid the risk of

electric shock or short circuit during installa-

tion.

! Do not attempt to disassemble or modify this

unit. Doing so may result in fire, electric

shock or other malfunction.

<5707000012760V>4

Before you start

<5707000012760V> <1>

English

Français

CLASS D MONO AMPLIFIER

AMPLIFICATEUR MONO DE CLASSE D

GM-D8701

GM-DX871

GM-D9701

GM-DX971

Owner’s Manual

Mode d’emploi

<5707000012761V> UC

Thank you

for purchasing this PIONEER

product

To ensure proper use, please read through this

manual before using this product. It is espe

cially important that you read and observe

WARNINGs and CAUTIONs in this manual.

Please keep the manual in a safe and accessible

place for future reference.

Information to User

Alteration or modifications carried out without

appropriate authorization may invalidate the

user’s right to operate the equipment.

Note

This equipment has been tested and found

to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reason

able protection against harmful interference

n a residential installation. This equipment

generates, uses and can radiate radio fre

quency energy and, if not installed and used

n accordance with the instructions, may

cause harmful interference to radio commu

nications. However, there is no guarantee

at interference will not occur in a particu-

lar installation. If this equipment does cause

armful interference to radio or television

reception, which can be determined by

turning the equipment off and on, the user is

encouraged to try to correct the interference

by one or more of the following measures:

— Reorient or relocate the receiving

antenna.

— Increase the separation between the

equipment and receiver.

— Connect the equipment into an out-

let on a circuit different from that to

hich the receiver is connected.

— Consult the dealer or an experienced

radio/TV technician for help.

FEDERAL COMMUNICATIONS

COMMISSION SUPPLIER’S DECLARATION

OF CONFORMITY

Product Name: Class D Mono Amplifier

Model Number: GM-D8701/GM-DX871/

GM-D9701/GM-DX971

Responsible Party Name: PIONEER

ELECTRONICS (USA) INC.

SERVICE SUPPORT DIVISION

Address: 2050 W. 190TH STREET, SUITE 100,

TORRANCE, CA 90504, U.S.A.

Phone: 1-800-421-1404

URL:

https://www.pioneerelectronics.com/PUSA/

After-sales service for

Pioneer products

Please contact the dealer or distributor from

where you purchased this unit for after-sales

service (including warranty conditions) or any

other information. In case the necessary infor

mation is not available, please contact the

ompanies listed below:

Please do not ship your unit to the companies

at the addresses listed below for repair without

advance contact.

USA & CANADA

Pioneer Electronics (USA) Inc.

CUSTOMER SUPPORT DIVISION

P.O. Box 1760

Long Beach, CA 90801-1760

800-421-1404

For warranty information, please see the Limited

Warranty sheet included with this unit.

If you experience problems

Should this product fail to operate properly,

please contact your dealer or nearest autho-

rized Pioneer Service Station.

Visit our website

http://www.pioneerelectronics.com

in Canada

http://www.pioneerelectronics.ca

 Learn about product updates (such as

firmware updates) for your product.

 Register your product to receive notices

about product updates and to safeguard

purchase details in our files in the event of

loss or theft.



Access owner’s manuals, spare parts infor-

mation, service information, and much

ore.

The Safety of Your Ears is in

Your Hands

Get the most out of your equipment by playing

it at a safe level—a level that lets the sound

come through clearly without annoying blar

ing or distortion and, most importantly, with-

out affecting your sensitive hearing. Sound

an be deceiving. Over time, your hearing

“comfort level” adapts to higher volumes of

sound, so what sounds “normal” can actually

be loud and harmful to your hearing. Guard

against this by setting your equipment at a

safe level BEFORE your hearing adapts.

ESTABLISH A SAFE LEVEL:

 Set your volume control at a low setting.

 Slowly increase the sound until you can

hear it comfortably and clearly, without

distortion.

 Once you have established a comfortable

sound level, set the dial and leave it there.

BE SURE TO OBSERVE THE FOLLOWING

GUIDELINES:

 Do not turn up the volume so high that you

can’t hear what’s around you.

 Use caution or temporarily discontinue use

in potentially hazardous situations.

 Do not use headphones while operating a

motorized vehicle; the use of headphones

may create a traffic hazard and is illegal in

many areas.

About This Product

This product is a mono amplifier for subwoofer. If

both L (left) and R (right) channels are connected

to the RCA input of this product, output is mixed

because this product is a mono amplifier.

Before connecting/

installing the amplier

WARNING

 This product contains chemicals known to the

State of California and other governmental

entities tocause cancer and birth defects or

other reproductive harm. Wash hands after

handling.



Slots and openings in the cabinet are provided

for ventilation to ensure reliable operation

of the product, and to protect it from over-

heating. To prevent fire hazard, the openings

should never be blocked or covered with items

(such as papers, floor mat, cloths).

 This unit is for vehicles with a 12 V battery and

negative grounding. Before installing in rec-

reational vehicles, trucks or buses, check the

battery voltage.

 When installing this unit, make sure to con-

nect the ground wire first. Ensure that the

ground wire is properly connected to the

metal parts of the car’s body. The ground wire

of the one of this unit must be connected to

the car separately with different screws. If the

screw for the ground wire loosens or falls out,

it could result in fire, generation of smoke or

malfunction.

 Be sure to install the fuse to the battery wire.

 Always use a fuse of the rating prescribed.

The use of an improper fuse could result in

overheating and smoke, damage to the prod-

uct, and injury, including burns.

 Check the connections of the power supply

and speakers if the fuse of the separately

sold battery wire or the amplifier fuse blows.

Determine and resolve the cause, then

replace the fuse with and identical equivalent.

 Always install the amplifier on a flat surface.

Do not install the amplifier on a surface that

is not flat or on a surface with a protrusion.

Doing so could result in malfunction.

 When installing the amplifier, do not allow

parts such as extra screws to get caught

between the amplifier and the automobile.

Doing so could cause malfunction.

<5707000012762V> UC

Tous droits de reproduction et de traduction

réservés.

CAUTION

! Always keep the volume low enough to hear

outside sounds.

! Extended use of the car stereo while the en-

gine is at rest or idling may exhaust the bat-

tery.

! This product is evaluated in moderate and tro-

pical climate condition under the Audio, video

and similar electronic apparatus - Safety re-

quirements, IEC 60065.

! The graphical symbol

placed on the

product means direct current.

! Connect either of three subwoofers to the am-

plifier; 1: a subwoofer with a 300 W (GM-D8701

and GM-DX871) / 500 W (GM-D9701 and GM-

DX971) or larger nominal input and an impe-

dance 4 W, 2: a subwoofer with a 500 W (GM-

D8701 and GM-DX871) / 800 W (GM-D9701

and GM-DX971) or larger nominal input and

an impedance 2 W or 3: a subwoofer with a

800 W (GM-D8701 and GM-DX871) / 1 200 W

(GM-D9701 and GM-DX971) or larger nominal

input and an impedance 1 W.

If the nominal input and impedance are out of

the above ranges, the subwoofer may catch

fire, emit smoke or become damaged.

About the protection function

This product has protection function. When this

product detects something abnormal, the follow-

ing functions will operate to protect the product

and speaker output.

! The POWER/PROTECT indicator will turn red

and the amplifier will shut down in the situa-

tions outlined below.

— If the temperature inside the amplifier gets

too high.

— If a DC voltage is applied to the speaker

output terminal.

! The POWER/PROTECT indicator will turn red

and the output will be muted in the situations

outlined below.

— If the speaker output terminal and speaker

wire are short-circuited.

Important (Serial number)

The serial number is located on the bottom of

this unit. For your own security and convenience,

be sure to record this number on the enclosed

warranty card.

<5707000012760V>5

Before you start

What’s what

GM-D8701 and GM-DX871

Front side

21 3 4

Rear side

GM-D9701 and GM-DX971

Front side

21 3 4

Rear side

To adjust the switch, use a flathead screwdri-

ver if needed.

1 POWER/PROTECT indicator

The power indicator lights up to indicate

power ON.

! If something is not normal, the indicator

turns red.

2 GAIN (gain) control

If the output remains low, even when the car

stereo volume is turned up, turn the con-

trols to a lower level. If distortion occurs

when the car stereo volume is turned up,

turn these controls to a higher level.

! For use with an RCA equipped car stereo

(standard output of 500 mV), set to the

NORMAL position. For use with an RCA

equipped Pioneer car stereo, with maxi-

mum output of 4 V or more, adjust level

to match that of the car stereo output.

! For use with an RCA equipped car stereo

with output of 4 V, set to the H position.

! If you hear too much noise when using

the speaker input terminals, turn the

gain control to higher level.

3 LPF (low-pass filter) cut off frequency

control

You can select a cut off frequency from

40 Hz to 240 Hz.

4 BASS BOOST REMOTE (bass boost level

remote control) jack

By connecting the Bass boost level remote

control to the jack on the main unit, you will

be able to select a bass boost level from

0 dB to 18 dB.

For instruction of connecting the bass boost

remote control to the amplifier, see the Con-

nection diagram.

Setting gain properly

! Protective function included to prevent

malfunction of the unit and/or speakers

due to excessive output, improper use or

improper connection.

! When outputting high volume sound etc.,

this function cuts off the output for a few

seconds as a normal function, but output

is restored when the volume of the head

unit is turned down.

<5707000012760V>6

Setting the unit

! A cut in sound output may indicate impro-

per setting of the gain control. To ensure

continuous sound output with the head

unit at a high volume, set amplifier gain

control to a level appropriate for the preout

maximum output level of the head unit, so

that volume can remain unchanged and to

control excess output.

! Despite correct volume and gain settings,

the unit sound still cuts out periodically. In

such cases, please contact the nearest

authorized Pioneer Service Station.

Gain control of this unit

Preout level: 2 V (Standard: 500 mV)

Preout level: 4 V

Above illustration shows NORMAL gain set-

ting.

Relationship between amplifier gain

and head unit output power

If amplifier gain is raised improperly, this will

simply increase distortion, with little increase

in power.

Signal waveform when outputting at

high volume using amplifier gain

control

If the signal waveform is distorted due to high

output, even if the amplifier gain is raised, the

output power will change only slightly.

<5707000012760V>7

Setting the unit

Connection diagram

1 Battery wire (sold separately)

! The maximum length of the wire be-

tween the fuse and the positive + term-

inal of the battery is 30 cm (12 in.).

! For the wire size, refer to Connecting the

power terminal. The battery wire, the

ground wire and the optional direct

ground wire must be same size. After

making all other connections at the am-

plifier, connect the battery wire terminal

of the amplifier to the positive + term-

inal of the battery.

2 Fuse 100 A (GM-D8701 and GM-DX871) / 150 A

(GM-D9701 and GM-DX971) (sold separately)

Each amplifier must be separately fused at

100 A (GM-D8701 and GM-DX871) / 150 A (GM-

D9701 and GM-DX971).

3 Positive + terminal

4 Negative (*) terminal

5 Battery (sold separately)

6 Ground wire, Terminal (sold separately)

The ground wires must be same size as the

battery wire.

Connect to metal body or chassis.

7 Car stereo with RCA output jacks (sold sepa-

rately)

8 External output

9 Connecting wire with RCA pin plugs (sold se-

parately)

a Amplifier with RCA input jacks (sold sepa-

rately)

b Bass boost level remote control

c Bass boost level remote control wire (5 m

(16 ft. 5in.))

d RCA input jack

e RCA output jack

f System remote control wire (sold separately)

Connect male terminal of this wire to the sys-

tem remote control terminal of the car stereo.

The female terminal can be connected to the

auto-antenna relay control terminal. If the car

stereo lacks a system remote control terminal,

connect the male terminal to the power term-

inal via the ignition switch.

g Speaker output terminals

Please see the following section for speaker

connection instructions. Refer to Connections

when using the speaker input wire.

h Fuse 40 A × 2 (GM-D8701 and GM-DX871) /

40 A × 3 (GM-D9701 and GM-DX971)

i Front side

j Rear side

Before connecting the

amplifier

WARNING

! Secure the wiring with cable clamps or adhe-

sive tape. To protect the wiring, wrap sections

in contact with metal parts in adhesive tape.

! Never cut the insulation of the power supply

to feed power to other equipment. Current ca-

pacity of the wire is limited.

CAUTION

! Never shorten any wires, the protection circuit

may malfunction.

<5707000012760V>8

Connecting the units

 Do not allow this unit to come into contact with

liquids. Electrical shock could result. Also, dam

age to this unit, smoke, and overheating could

result from contact with liquids. The surfaces

of the amplifier and any attached speakers may

also heat up and cause minor burns.

 In the event of any abnormality, the power

supply to the amplifier is cut off to prevent

equipment malfunction. If this occurs, switch

the system power off and check the power

supply and speaker connections. If you are

unable to determine the cause, please contact

your dealer.

 Always disconnect the negative * terminal of

the battery beforehand to avoid the risk of elec

tric shock or short circuit during installation.

 Do not attempt to disassemble or modify

this unit. Doing so may result in fire, electric

shock or other malfunction.

CAUTION

! Always keep the volume low enough to hear

outside sounds.

! Extended use of the car stereo while the en-

gine is at rest or idling may exhaust the bat-

tery.

! This product is evaluated in moderate and tro-

pical climate condition under the Audio, video

and similar electronic apparatus - Safety re-

quirements, IEC 60065.

! The graphical symbol

placed on the

product means direct current.

! Connect either of three subwoofers to the am-

plifier; 1: a subwoofer with a 300 W (GM-D8701

and GM-DX871) / 500 W (GM-D9701 and GM-

DX971) or larger nominal input and an impe-

dance 4 W, 2: a subwoofer with a 500 W (GM-

D8701 and GM-DX871) / 800 W (GM-D9701

and GM-DX971) or larger nominal input and

an impedance 2 W or 3: a subwoofer with a

800 W (GM-D8701 and GM-DX871) / 1 200 W

(GM-D9701 and GM-DX971) or larger nominal

input and an impedance 1 W.

If the nominal input and impedance are out of

the above ranges, the subwoofer may catch

fire, emit smoke or become damaged.

About the protection function

This product has protection function. When this

product detects something abnormal, the follow-

ing functions will operate to protect the product

and speaker output.

! The POWER/PROTECT indicator will turn red

and the amplifier will shut down in the situa-

tions outlined below.

— If the temperature inside the amplifier gets

too high.

— If a DC voltage is applied to the speaker

output terminal.

! The POWER/PROTECT indicator will turn red

and the output will be muted in the situations

outlined below.

— If the speaker output terminal and speaker

wire are short-circuited.

Important (Serial number)

The serial number is located on the bottom of

this unit. For your own security and convenience,

be sure to record this number on the enclosed

warranty card.

<5707000012760V>5

Before you start

What’s what

GM-D8701 and GM-DX871

Front side

21 3 4

Rear side

GM-D9701 and GM-DX971

Front side

21 3 4

Rear side

To adjust the switch, use a flathead screwdri-

ver if needed.

1 POWER/PROTECT indicator

The power indicator lights up to indicate

power ON.

! If something is not normal, the indicator

turns red.

2 GAIN (gain) control

If the output remains low, even when the car

stereo volume is turned up, turn the con-

trols to a lower level. If distortion occurs

when the car stereo volume is turned up,

turn these controls to a higher level.

! For use with an RCA equipped car stereo

(standard output of 500 mV), set to the

NORMAL position. For use with an RCA

equipped Pioneer car stereo, with maxi-

mum output of 4 V or more, adjust level

to match that of the car stereo output.

! For use with an RCA equipped car stereo

with output of 4 V, set to the H position.

! If you hear too much noise when using

the speaker input terminals, turn the

gain control to higher level.

3 LPF (low-pass filter) cut off frequency

control

You can select a cut off frequency from

40 Hz to 240 Hz.

4 BASS BOOST REMOTE (bass boost level

remote control) jack

By connecting the Bass boost level remote

control to the jack on the main unit, you will

be able to select a bass boost level from

0 dB to 18 dB.

For instruction of connecting the bass boost

remote control to the amplifier, see the Con-

nection diagram.

Setting gain properly

! Protective function included to prevent

malfunction of the unit and/or speakers

due to excessive output, improper use or

improper connection.

! When outputting high volume sound etc.,

this function cuts off the output for a few

seconds as a normal function, but output

is restored when the volume of the head

unit is turned down.

<5707000012760V>6

Setting the unit

! A cut in sound output may indicate impro-

per setting of the gain control. To ensure

continuous sound output with the head

unit at a high volume, set amplifier gain

control to a level appropriate for the preout

maximum output level of the head unit, so

that volume can remain unchanged and to

control excess output.

! Despite correct volume and gain settings,

the unit sound still cuts out periodically. In

such cases, please contact the nearest

authorized Pioneer Service Station.

Gain control of this unit

Preout level: 2 V (Standard: 500 mV)

Preout level: 4 V

Above illustration shows NORMAL gain set-

ting.

Relationship between amplifier gain

and head unit output power

If amplifier gain is raised improperly, this will

simply increase distortion, with little increase

in power.

Signal waveform when outputting at

high volume using amplifier gain

control

If the signal waveform is distorted due to high

output, even if the amplifier gain is raised, the

output power will change only slightly.

<5707000012760V>7

Setting the unit

Connection diagram

1 Battery wire (sold separately)

! The maximum length of the wire be-

tween the fuse and the positive + term-

inal of the battery is 30 cm (12 in.).

! For the wire size, refer to Connecting the

power terminal. The battery wire, the

ground wire and the optional direct

ground wire must be same size. After

making all other connections at the am-

plifier, connect the battery wire terminal

of the amplifier to the positive + term-

inal of the battery.

2 Fuse 100 A (GM-D8701 and GM-DX871) / 150 A

(GM-D9701 and GM-DX971) (sold separately)

Each amplifier must be separately fused at

100 A (GM-D8701 and GM-DX871) / 150 A (GM-

D9701 and GM-DX971).

3 Positive + terminal

4 Negative (*) terminal

5 Battery (sold separately)

6 Ground wire, Terminal (sold separately)

The ground wires must be same size as the

battery wire.

Connect to metal body or chassis.

7 Car stereo with RCA output jacks (sold sepa-

rately)

8 External output

9 Connecting wire with RCA pin plugs (sold se-

parately)

a Amplifier with RCA input jacks (sold sepa-

rately)

b Bass boost level remote control

c Bass boost level remote control wire (5 m

(16 ft. 5in.))

d RCA input jack

e RCA output jack

f System remote control wire (sold separately)

Connect male terminal of this wire to the sys-

tem remote control terminal of the car stereo.

The female terminal can be connected to the

auto-antenna relay control terminal. If the car

stereo lacks a system remote control terminal,

connect the male terminal to the power term-

inal via the ignition switch.

g Speaker output terminals

Please see the following section for speaker

connection instructions. Refer to Connections

when using the speaker input wire.

h Fuse 40 A × 2 (GM-D8701 and GM-DX871) /

40 A × 3 (GM-D9701 and GM-DX971)

i Front side

j Rear side

Before connecting the

amplifier

WARNING

! Secure the wiring with cable clamps or adhe-

sive tape. To protect the wiring, wrap sections

in contact with metal parts in adhesive tape.

! Never cut the insulation of the power supply

to feed power to other equipment. Current ca-

pacity of the wire is limited.

CAUTION

! Never shorten any wires, the protection circuit

may malfunction.

<5707000012760V>8

Connecting the units

CAUTION

! Always keep the volume low enough to hear

outside sounds.

! Extended use of the car stereo while the en-

gine is at rest or idling may exhaust the bat-

tery.

! This product is evaluated in moderate and tro-

pical climate condition under the Audio, video

and similar electronic apparatus - Safety re-

quirements, IEC 60065.

! The graphical symbol

placed on the

product means direct current.

! Connect either of three subwoofers to the am-

plifier; 1: a subwoofer with a 300 W (GM-D8701

and GM-DX871) / 500 W (GM-D9701 and GM-

DX971) or larger nominal input and an impe-

dance 4 W, 2: a subwoofer with a 500 W (GM-

D8701 and GM-DX871) / 800 W (GM-D9701

and GM-DX971) or larger nominal input and

an impedance 2 W or 3: a subwoofer with a

800 W (GM-D8701 and GM-DX871) / 1 200 W

(GM-D9701 and GM-DX971) or larger nominal

input and an impedance 1 W.

If the nominal input and impedance are out of

the above ranges, the subwoofer may catch

fire, emit smoke or become damaged.

About the protection function

This product has protection function. When this

product detects something abnormal, the follow-

ing functions will operate to protect the product

and speaker output.

! The POWER/PROTECT indicator will turn red

and the amplifier will shut down in the situa-

tions outlined below.

— If the temperature inside the amplifier gets

too high.

— If a DC voltage is applied to the speaker

output terminal.

! The POWER/PROTECT indicator will turn red

and the output will be muted in the situations

outlined below.

— If the speaker output terminal and speaker

wire are short-circuited.

Important (Serial number)

The serial number is located on the bottom of

this unit. For your own security and convenience,

be sure to record this number on the enclosed

warranty card.

<5707000012760V>5

Before you start

What’s what

GM-D8701 and GM-DX871

Front side

21 3 4

Rear side

GM-D9701 and GM-DX971

Front side

21 3 4

Rear side

To adjust the switch, use a flathead screwdri-

ver if needed.

1 POWER/PROTECT indicator

The power indicator lights up to indicate

power ON.

! If something is not normal, the indicator

turns red.

2 GAIN (gain) control

If the output remains low, even when the car

stereo volume is turned up, turn the con-

trols to a lower level. If distortion occurs

when the car stereo volume is turned up,

turn these controls to a higher level.

! For use with an RCA equipped car stereo

(standard output of 500 mV), set to the

NORMAL position. For use with an RCA

equipped Pioneer car stereo, with maxi-

mum output of 4 V or more, adjust level

to match that of the car stereo output.

! For use with an RCA equipped car stereo

with output of 4 V, set to the H position.

! If you hear too much noise when using

the speaker input terminals, turn the

gain control to higher level.

3 LPF (low-pass filter) cut off frequency

control

You can select a cut off frequency from

40 Hz to 240 Hz.

4 BASS BOOST REMOTE (bass boost level

remote control) jack

By connecting the Bass boost level remote

control to the jack on the main unit, you will

be able to select a bass boost level from

0 dB to 18 dB.

For instruction of connecting the bass boost

remote control to the amplifier, see the Con-

nection diagram.

Setting gain properly

! Protective function included to prevent

malfunction of the unit and/or speakers

due to excessive output, improper use or

improper connection.

! When outputting high volume sound etc.,

this function cuts off the output for a few

seconds as a normal function, but output

is restored when the volume of the head

unit is turned down.

<5707000012760V>6

Setting the unit

! A cut in sound output may indicate impro-

per setting of the gain control. To ensure

continuous sound output with the head

unit at a high volume, set amplifier gain

control to a level appropriate for the preout

maximum output level of the head unit, so

that volume can remain unchanged and to

control excess output.

! Despite correct volume and gain settings,

the unit sound still cuts out periodically. In

such cases, please contact the nearest

authorized Pioneer Service Station.

Gain control of this unit

Preout level: 2 V (Standard: 500 mV)

Preout level: 4 V

Above illustration shows NORMAL gain set-

ting.

Relationship between amplifier gain

and head unit output power

If amplifier gain is raised improperly, this will

simply increase distortion, with little increase

in power.

Signal waveform when outputting at

high volume using amplifier gain

control

If the signal waveform is distorted due to high

output, even if the amplifier gain is raised, the

output power will change only slightly.

<5707000012760V>7

Setting the unit

Connection diagram

1 Battery wire (sold separately)

! The maximum length of the wire be-

tween the fuse and the positive + term-

inal of the battery is 30 cm (12 in.).

! For the wire size, refer to Connecting the

power terminal. The battery wire, the

ground wire and the optional direct

ground wire must be same size. After

making all other connections at the am-

plifier, connect the battery wire terminal

of the amplifier to the positive + term-

inal of the battery.

2 Fuse 100 A (GM-D8701 and GM-DX871) / 150 A

(GM-D9701 and GM-DX971) (sold separately)

Each amplifier must be separately fused at

100 A (GM-D8701 and GM-DX871) / 150 A (GM-

D9701 and GM-DX971).

3 Positive + terminal

4 Negative (*) terminal

5 Battery (sold separately)

6 Ground wire, Terminal (sold separately)

The ground wires must be same size as the

battery wire.

Connect to metal body or chassis.

7 Car stereo with RCA output jacks (sold sepa-

rately)

8 External output

9 Connecting wire with RCA pin plugs (sold se-

parately)

a Amplifier with RCA input jacks (sold sepa-

rately)

b Bass boost level remote control

c Bass boost level remote control wire (5 m

(16 ft. 5in.))

d RCA input jack

e RCA output jack

f System remote control wire (sold separately)

Connect male terminal of this wire to the sys-

tem remote control terminal of the car stereo.

The female terminal can be connected to the

auto-antenna relay control terminal. If the car

stereo lacks a system remote control terminal,

connect the male terminal to the power term-

inal via the ignition switch.

g Speaker output terminals

Please see the following section for speaker

connection instructions. Refer to Connections

when using the speaker input wire.

h Fuse 40 A × 2 (GM-D8701 and GM-DX871) /

40 A × 3 (GM-D9701 and GM-DX971)

i Front side

j Rear side

Before connecting the

amplifier

WARNING

! Secure the wiring with cable clamps or adhe-

sive tape. To protect the wiring, wrap sections

in contact with metal parts in adhesive tape.

! Never cut the insulation of the power supply

to feed power to other equipment. Current ca-

pacity of the wire is limited.

CAUTION

! Never shorten any wires, the protection circuit

may malfunction.

<5707000012760V>8

Connecting the units

CAUTION

! Always keep the volume low enough to hear

outside sounds.

! Extended use of the car stereo while the en-

gine is at rest or idling may exhaust the bat-

tery.

! This product is evaluated in moderate and tro-

pical climate condition under the Audio, video

and similar electronic apparatus - Safety re-

quirements, IEC 60065.

! The graphical symbol

placed on the

product means direct current.

! Connect either of three subwoofers to the am-

plifier; 1: a subwoofer with a 300 W (GM-D8701

and GM-DX871) / 500 W (GM-D9701 and GM-

DX971) or larger nominal input and an impe-

dance 4 W, 2: a subwoofer with a 500 W (GM-

D8701 and GM-DX871) / 800 W (GM-D9701

and GM-DX971) or larger nominal input and

an impedance 2 W or 3: a subwoofer with a

800 W (GM-D8701 and GM-DX871) / 1 200 W

(GM-D9701 and GM-DX971) or larger nominal

input and an impedance 1 W.

If the nominal input and impedance are out of

the above ranges, the subwoofer may catch

fire, emit smoke or become damaged.

About the protection function

This product has protection function. When this

product detects something abnormal, the follow-

ing functions will operate to protect the product

and speaker output.

! The POWER/PROTECT indicator will turn red

and the amplifier will shut down in the situa-

tions outlined below.

— If the temperature inside the amplifier gets

too high.

— If a DC voltage is applied to the speaker

output terminal.

! The POWER/PROTECT indicator will turn red

and the output will be muted in the situations

outlined below.

— If the speaker output terminal and speaker

wire are short-circuited.

Important (Serial number)

The serial number is located on the bottom of

this unit. For your own security and convenience,

be sure to record this number on the enclosed

warranty card.

<5707000012760V>5

Before you start

What’s what

GM-D8701 and GM-DX871

Front side

21 3 4

Rear side

GM-D9701 and GM-DX971

Front side

21 3 4

Rear side

To adjust the switch, use a flathead screwdri-

ver if needed.

1 POWER/PROTECT indicator

The power indicator lights up to indicate

power ON.

! If something is not normal, the indicator

turns red.

2 GAIN (gain) control

If the output remains low, even when the car

stereo volume is turned up, turn the con-

trols to a lower level. If distortion occurs

when the car stereo volume is turned up,

turn these controls to a higher level.

! For use with an RCA equipped car stereo

(standard output of 500 mV), set to the

NORMAL position. For use with an RCA

equipped Pioneer car stereo, with maxi-

mum output of 4 V or more, adjust level

to match that of the car stereo output.

! For use with an RCA equipped car stereo

with output of 4 V, set to the H position.

! If you hear too much noise when using

the speaker input terminals, turn the

gain control to higher level.

3 LPF (low-pass filter) cut off frequency

control

You can select a cut off frequency from

40 Hz to 240 Hz.

4 BASS BOOST REMOTE (bass boost level

remote control) jack

By connecting the Bass boost level remote

control to the jack on the main unit, you will

be able to select a bass boost level from

0 dB to 18 dB.

For instruction of connecting the bass boost

remote control to the amplifier, see the Con-

nection diagram.

Setting gain properly

! Protective function included to prevent

malfunction of the unit and/or speakers

due to excessive output, improper use or

improper connection.

! When outputting high volume sound etc.,

this function cuts off the output for a few

seconds as a normal function, but output

is restored when the volume of the head

unit is turned down.

<5707000012760V>6

Setting the unit

! A cut in sound output may indicate impro-

per setting of the gain control. To ensure

continuous sound output with the head

unit at a high volume, set amplifier gain

control to a level appropriate for the preout

maximum output level of the head unit, so

that volume can remain unchanged and to

control excess output.

! Despite correct volume and gain settings,

the unit sound still cuts out periodically. In

such cases, please contact the nearest

authorized Pioneer Service Station.

Gain control of this unit

Preout level: 2 V (Standard: 500 mV)

Preout level: 4 V

Above illustration shows NORMAL gain set-

ting.

Relationship between amplifier gain

and head unit output power

If amplifier gain is raised improperly, this will

simply increase distortion, with little increase

in power.

Signal waveform when outputting at

high volume using amplifier gain

control

If the signal waveform is distorted due to high

output, even if the amplifier gain is raised, the

output power will change only slightly.

<5707000012760V>7

Setting the unit

Connection diagram

1 Battery wire (sold separately)

! The maximum length of the wire be-

tween the fuse and the positive + term-

inal of the battery is 30 cm (12 in.).

! For the wire size, refer to Connecting the

power terminal. The battery wire, the

ground wire and the optional direct

ground wire must be same size. After

making all other connections at the am-

plifier, connect the battery wire terminal

of the amplifier to the positive + term-

inal of the battery.

2 Fuse 100 A (GM-D8701 and GM-DX871) / 150 A

(GM-D9701 and GM-DX971) (sold separately)

Each amplifier must be separately fused at

100 A (GM-D8701 and GM-DX871) / 150 A (GM-

D9701 and GM-DX971).

3 Positive + terminal

4 Negative (*) terminal

5 Battery (sold separately)

6 Ground wire, Terminal (sold separately)

The ground wires must be same size as the

battery wire.

Connect to metal body or chassis.

7 Car stereo with RCA output jacks (sold sepa-

rately)

8 External output

9 Connecting wire with RCA pin plugs (sold se-

parately)

a Amplifier with RCA input jacks (sold sepa-

rately)

b Bass boost level remote control

c Bass boost level remote control wire (5 m

(16 ft. 5in.))

d RCA input jack

e RCA output jack

f System remote control wire (sold separately)

Connect male terminal of this wire to the sys-

tem remote control terminal of the car stereo.

The female terminal can be connected to the

auto-antenna relay control terminal. If the car

stereo lacks a system remote control terminal,

connect the male terminal to the power term-

inal via the ignition switch.

g Speaker output terminals

Please see the following section for speaker

connection instructions. Refer to Connections

when using the speaker input wire.

h Fuse 40 A × 2 (GM-D8701 and GM-DX871) /

40 A × 3 (GM-D9701 and GM-DX971)

i Front side

j Rear side

Before connecting the

amplifier

WARNING

! Secure the wiring with cable clamps or adhe-

sive tape. To protect the wiring, wrap sections

in contact with metal parts in adhesive tape.

! Never cut the insulation of the power supply

to feed power to other equipment. Current ca-

pacity of the wire is limited.

CAUTION

! Never shorten any wires, the protection circuit

may malfunction.

<5707000012760V>8

Connecting the units

CAUTION

! Always keep the volume low enough to hear

outside sounds.

! Extended use of the car stereo while the en-

gine is at rest or idling may exhaust the bat-

tery.

! This product is evaluated in moderate and tro-

pical climate condition under the Audio, video

and similar electronic apparatus - Safety re-

quirements, IEC 60065.

! The graphical symbol

placed on the

product means direct current.

! Connect either of three subwoofers to the am-

plifier; 1: a subwoofer with a 300 W (GM-D8701

and GM-DX871) / 500 W (GM-D9701 and GM-

DX971) or larger nominal input and an impe-

dance 4 W, 2: a subwoofer with a 500 W (GM-

D8701 and GM-DX871) / 800 W (GM-D9701

and GM-DX971) or larger nominal input and

an impedance 2 W or 3: a subwoofer with a

800 W (GM-D8701 and GM-DX871) / 1 200 W

(GM-D9701 and GM-DX971) or larger nominal

input and an impedance 1 W.

If the nominal input and impedance are out of

the above ranges, the subwoofer may catch

fire, emit smoke or become damaged.

About the protection function

This product has protection function. When this

product detects something abnormal, the follow-

ing functions will operate to protect the product

and speaker output.

! The POWER/PROTECT indicator will turn red

and the amplifier will shut down in the situa-

tions outlined below.

— If the temperature inside the amplifier gets

too high.

— If a DC voltage is applied to the speaker

output terminal.

! The POWER/PROTECT indicator will turn red

and the output will be muted in the situations

outlined below.

— If the speaker output terminal and speaker

wire are short-circuited.

Important (Serial number)

The serial number is located on the bottom of

this unit. For your own security and convenience,

be sure to record this number on the enclosed

warranty card.

<5707000012760V>5

Before you start

What’s what

GM-D8701 and GM-DX871

Front side

21 3 4

Rear side

GM-D9701 and GM-DX971

Front side

21 3 4

Rear side

To adjust the switch, use a flathead screwdri-

ver if needed.

1 POWER/PROTECT indicator

The power indicator lights up to indicate

power ON.

! If something is not normal, the indicator

turns red.

2 GAIN (gain) control

If the output remains low, even when the car

stereo volume is turned up, turn the con-

trols to a lower level. If distortion occurs

when the car stereo volume is turned up,

turn these controls to a higher level.

! For use with an RCA equipped car stereo

(standard output of 500 mV), set to the

NORMAL position. For use with an RCA

equipped Pioneer car stereo, with maxi-

mum output of 4 V or more, adjust level

to match that of the car stereo output.

! For use with an RCA equipped car stereo

with output of 4 V, set to the H position.

! If you hear too much noise when using

the speaker input terminals, turn the

gain control to higher level.

3 LPF (low-pass filter) cut off frequency

control

You can select a cut off frequency from

40 Hz to 240 Hz.

4 BASS BOOST REMOTE (bass boost level

remote control) jack

By connecting the Bass boost level remote

control to the jack on the main unit, you will

be able to select a bass boost level from

0 dB to 18 dB.

For instruction of connecting the bass boost

remote control to the amplifier, see the Con-

nection diagram.

Setting gain properly

! Protective function included to prevent

malfunction of the unit and/or speakers

due to excessive output, improper use or

improper connection.

! When outputting high volume sound etc.,

this function cuts off the output for a few

seconds as a normal function, but output

is restored when the volume of the head

unit is turned down.

<5707000012760V>6

Setting the unit

! A cut in sound output may indicate impro-

per setting of the gain control. To ensure

continuous sound output with the head

unit at a high volume, set amplifier gain

control to a level appropriate for the preout

maximum output level of the head unit, so

that volume can remain unchanged and to

control excess output.

! Despite correct volume and gain settings,

the unit sound still cuts out periodically. In

such cases, please contact the nearest

authorized Pioneer Service Station.

Gain control of this unit

Preout level: 2 V (Standard: 500 mV)

Preout level: 4 V

Above illustration shows NORMAL gain set-

ting.

Relationship between amplifier gain

and head unit output power

If amplifier gain is raised improperly, this will

simply increase distortion, with little increase

in power.

Signal waveform when outputting at

high volume using amplifier gain

control

If the signal waveform is distorted due to high

output, even if the amplifier gain is raised, the

output power will change only slightly.

<5707000012760V>7

Setting the unit

Connection diagram

1 Battery wire (sold separately)

! The maximum length of the wire be-

tween the fuse and the positive + term-

inal of the battery is 30 cm (12 in.).

! For the wire size, refer to Connecting the

power terminal. The battery wire, the

ground wire and the optional direct

ground wire must be same size. After

making all other connections at the am-

plifier, connect the battery wire terminal

of the amplifier to the positive + term-

inal of the battery.

2 Fuse 100 A (GM-D8701 and GM-DX871) / 150 A

(GM-D9701 and GM-DX971) (sold separately)

Each amplifier must be separately fused at

100 A (GM-D8701 and GM-DX871) / 150 A (GM-

D9701 and GM-DX971).

3 Positive + terminal

4 Negative (*) terminal

5 Battery (sold separately)

6 Ground wire, Terminal (sold separately)

The ground wires must be same size as the

battery wire.

Connect to metal body or chassis.

7 Car stereo with RCA output jacks (sold sepa-

rately)

8 External output

9 Connecting wire with RCA pin plugs (sold se-

parately)

a Amplifier with RCA input jacks (sold sepa-

rately)

b Bass boost level remote control

c Bass boost level remote control wire (5 m

(16 ft. 5in.))

d RCA input jack

e RCA output jack

f System remote control wire (sold separately)

Connect male terminal of this wire to the sys-

tem remote control terminal of the car stereo.

The female terminal can be connected to the

auto-antenna relay control terminal. If the car

stereo lacks a system remote control terminal,

connect the male terminal to the power term-

inal via the ignition switch.

g Speaker output terminals

Please see the following section for speaker

connection instructions. Refer to Connections

when using the speaker input wire.

h Fuse 40 A × 2 (GM-D8701 and GM-DX871) /

40 A × 3 (GM-D9701 and GM-DX971)

i Front side

j Rear side

Before connecting the

amplifier

WARNING

! Secure the wiring with cable clamps or adhe-

sive tape. To protect the wiring, wrap sections

in contact with metal parts in adhesive tape.

! Never cut the insulation of the power supply

to feed power to other equipment. Current ca-

pacity of the wire is limited.

CAUTION

! Never shorten any wires, the protection circuit

may malfunction.

<5707000012760V>8

Connecting the units

! Never wire the speaker negative cable directly

to ground.

! Never band together multiple speaker’s nega-

tive cables.

! If the system remote control wire of the ampli-

fier is connected to the power terminal via the

ignition switch (12 V DC), the amplifier will re-

main on with the ignition whether the car

stereo is on or off, which may exhaust battery

if the engine is at rest or idling.

! Install and route the separately sold battery

wire as far as possible from the speaker wires.

Install and route the separately sold battery

wire, ground wire, speaker wires and the am-

plifier as far away as possible from the anten-

na, antenna cable and tuner.

Connecting the speakers

This amplifier can be connected to two speak-

ers in parallel. Connect the speaker leads to

suit the mode according to the figure shown

below.

Precautions for parallel connection

! When wiring two speakers in parallel, make

sure that the synthetic impedance is from

1 W to 8 W to prevent the amplifier from

catching fire, generating smoke and/or

being damaged.

! When connected in parallel with the syn-

thetic impedance less than 1 W, as a nor-

mal function, this amplifier may

automatically be set on mute if outputting

high volume sound. Turn down the volume

until the mute function is canceled.

When connecting to one speaker

Speaker output

When connecting to two speakers

The output from two speakers is the same as

that of one speaker.

Speaker output

<5707000012760V>9

Connecting the units

Connections when using

the speaker input wire

Connect the car stereo speaker output wires

to the amplifier using the supplied speaker

input wire with RCA pin cord.

1 Car Stereo

2 Speaker output

3 Red: Right +

4 Black: Right *

5 Black: Left *

6 White: Left +

7 Speaker input wire with RCA pin cord

To the RCA input jack of this unit

Notes

! If speaker input wires from a headunit are

connected to this amplifier, the amplifier will

automatically turn on when the headunit is

turned on. When the headunit is turned off,

the amplifier turns off automatically. This

function may not work with some headunits.

In such cases, please use a system remote

control wire (sold separately). If multiple am-

plifiers are to be connected together synchro-

nously, connect the head unit and all

amplifiers via the system remote control wire.

! Connect the system remote control wire when

you wish to only turn on the car stereo, not the

amplifier.

! This amplifier automatically selects an input

signal mode between the RCA level and the

speaker level by detecting an input signal.

Solderless terminal

connections

! Since the wire will become loose over time,

it must be periodically inspected and tigh-

tened as necessary.

! Do not solder or bind the ends of the

twisted wires.

! Fasten while making sure to not to clamp

the insulating sheath of the wire.

! Use the supplied hexagonal wrench to

tighten and loosen the terminal screw of

the amplifier and use it to securely fasten

the wire. Be careful to avoid excessive tigh-

tening of this screw, which may damage

the wire.

Connecting the power terminal

WARNING

If the battery wire is not securely fixed to the term-

inal using the terminal screws, there is a risk of

overheating, malfunction and injury, including

minor burns.

! Always use the recommended battery and

ground wire, which is sold separately. Con-

nect the battery wire directly to the car bat-

tery positive (+) terminal and the ground

wire to the car body.

! Recommended wires size (AWG: American

Wire Gauge) is as follows. The battery wire,

the ground wire and the optional direct

ground wire must be same size.

! Use a wire of 8 AWG to 16 AWG wire for the

speaker wire.

Battery wire and ground wire size

Wire length Wire size

less than 3.6 m (11 ft. 10 in.) 6 AWG

less than 6.4 m (20 ft. 12 in.) 4 AWG

<5707000012760V>10

Connecting the units

1 Route battery wire from engine com-

partment to the vehicle interior.

! When drilling a cable pass-hole into the ve-

hicle body and routing a battery wire thor-

ough it, take care not to short-circuit the

wire damaging it by the cut edges or burrs

of the hole.

After completing all other amplifier connec-

tions, finally connect the battery wire terminal

of the amplifier to the positive + battery term-

inal.

1 Positive + terminal

2 Battery wire (sold separately)

The maximum length of the wire between

the fuse and the positive + terminal of the

battery is 30 cm (12 in.).

3 Fuse 100 A (GM-D8701 and GM-DX871) /

150 A (GM-D9701 and GM-DX971) (sold se-

parately)

Each amplifier must be separately fused at

100 A (GM-D8701 and GM-DX871) / 150 A

(GM-D9701 and GM-DX971).

2 Use wire cutters or a utility knife to

strip the end of the battery wire, ground

wire and system remote control wire to ex-

pose about 10 mm (3/8 in.) of the end of

each of the wires, and then twist the ex-

posed ends of the wires.

Twist

10 mm (3/8 in.)

3 Connect the wires to the terminal.

Fix the wires securely with the terminal

screws.

1 Battery wire

2 Power terminal

3 Ground wire

4 GND terminal

5 System remote control wire

6 System remote control terminal

7 Terminal screws

<5707000012760V>11

Connecting the units

Connecting the speaker output

terminals

1 Use wire cutters or a utility knife to

strip the end of the speaker wires to ex-

pose about 10 mm (3/8 in.) of wire and

then twist the wire.

Twist

10 mm (3/8 in.)

2 Connect the speaker wires to the

speaker output terminals.

Fix the wires securely with the terminal

screws.

1 Terminal screws

2 Speaker wires

3 Speaker output terminals

Before installing the amplifier

WARNING

! To ensure proper installation, use the supplied

parts in the manner specified. If any parts

other than those supplied are used, they may

damage internal parts of the amplifier, or be-

come loose causing the amplifier to shut

down.

! Do not install in:

— Places where it could injure the driver or

passengers if the vehicle stops suddenly.

— Places where it may interfere with the dri-

ver, such as on the floor in front of the dri-

ver’s seat.

! Install tapping screws in such a way that the

screw tip does not touch any wire. This is im-

portant to prevent wires from being cut by vi-

bration of the car, which can result in fire.

! Make sure that wires do not get caught in the

sliding mechanism of the seats or touch the

legs of a person in the vehicle as short-circuit

may result.

! When drilling to install the amplifier, always

confirm no parts are behind the panel and

protect all cables and important equipment

(e.g. fuel/brake lines, wiring) from damage.

CAUTION

! To ensure proper heat dissipation of the ampli-

fier, ensure the following during installation:

— Allow adequate space above the amplifier

for proper ventilation.

— Do not cover the amplifier with a floor mat

or carpet.

! Place all cables away from hot places, such

as near the heater outlet.

! The optimal installation location differs de-

pending on the car model. Secure the ampli-

fier at a sufficiently rigid location.

! Check all connections and systems before

final installation.

! After installing the amplifier, confirm that the

spare tire, jack and tools can be easily re-

moved.

<5707000012760V>12

Connecting the units Installation

Attaching the Bass boost

remote control

Attach with tapping screws (3 mm × 10 mm

(1/8 in. × 3/8 in.)) at an easily accessible loca-

tion such as under the dashboard.

Tapping screws (3 mm × 10 mm (1/8 in. × 3/

8 in.))

Example of installation on

the floor mat or chassis

1 Place the amplifier in the desired instal-

lation location.

Insert the supplied tapping screws (4 mm ×

18 mm (5/32 in. × 3/4 in.)) into the screw holes

and push on the screws with a screwdriver so

they make an imprint where the installation

holes are to be located.

2 Drill 2.5 mm (3/32 in.) diameter holes at

the imprints either on the carpet or directly

on the chassis.

3 Install the amplifier with the use of

supplied tapping screws (4 mm × 18 mm

(5/32 in. × 3/4 in.)).

1 Tapping-screws (4 mm × 18 mm (5/32 in. ×

3/4 in.))

2 Drill a 2.5 mm (3/32 in.) diameter hole.

3 Floor mat or chassis

4 Hole-to-hole distance: 229.5 mm (9-1/32 in.)

(GM-D8701 and GM-DX871) / 279.5 mm

(11 in.) (GM-D9701 and GM-DX971)

5 Hole-to-hole distance: 191.5 mm

(7-17/32 in.)

<5707000012760V>13

Installation

Specifications

GM-D8701 and GM-DX871

Power source ............................. 14.4 V DC (10.8 V to 15.1 V

allowable)

Grounding system ................... Negative type

Current consumption ............ 22 A (at continuous power,

4 W)

Average current consumption

..................................................... 2.4 A (4 W for one channel)

3.6 A (2 W for one channel)

5.7 A (1 W for one channel)

Fuse ................................................ 40 A × 2

Dimensions (W × H × D) ... 252 mm × 60 mm ×

215 mm

(9-7/8 in. × 2-3/8 in. ×

8-1/2 in.)

Weight .......................................... 2.7 kg (6 lbs)

(Leads for wiring not in-

cluded)

Maximum power output ....... 600 W × 1 (4 W)/1600W×

1 (1 W)

Continuous power output ...300 W × 1 (at 14.4 V, 4 W,

20 Hz to 240 Hz, ≦ 1 % THD)

500 W × 1 (at 14.4 V, 2 W,

100 Hz, ≦ 1 % THD)

800 W × 1 (at 14.4 V, 1 W,

100 Hz, ≦ 1 % THD)

Load impedance ...................... 4 W (1 W to 8 W allowable)

Frequency response ............... 10 Hz to 240 Hz (+0 dB,

–3 dB)

Signal-to-noise ratio ............... 100 dB (IHF-A network)

Low pass filter:

Cut off frequency ........... 40 Hz to 240 Hz

Cut off slope ..................... –12 dB/oct

Bass boost:

Frequency .......................... 50 Hz

Level ..................................... 0 dB to 18 dB

Gain control:

RCA ...................................... 200 mV to 6.5 V

Speaker .............................. 0.8 V to 16 V

Maximum input level / impedance:

RCA ...................................... 6.5 V / 25 kW

Speaker .............................. 16 V / 12 kW

CEA2006 Specifications

Power output ............................. 300 W RMS × 1 Channel (at

14.4 V, 4 W, 20 Hz to 240 Hz

and ≦ 1 % THD+N)

500 W RMS × 1 Channel (at

14.4 V, 2 W, 100 Hz and ≦ 1%

THD+N)

800 W RMS × 1 Channel (at

14.4 V, 1 W, 100 Hz and ≦ 1%

THD+N)

S/N ratio ....................................... 75 dBA (reference: 1 W into

4 W)

GM-D9701 and GM-DX971

Power source ............................. 14.4 V DC (10.8 V to 15.1 V

allowable)

Grounding system ................... Negative type

Current consumption ............ 38 A (at continuous power,

4 W)

Average current consumption

..................................................... 3.5 A (4 W for one channel)

5.1 A (2 W for one channel)

7.5 A (1 W for one channel)

Fuse ................................................ 40 A × 3

Dimensions (W × H × D) ... 302 mm × 60 mm ×

215 mm

(11-7/8 in. × 2-3/8 in. ×

8-1/2 in.)

Weight .......................................... 3.1 kg (6.8 lbs)

(Leads for wiring not in-

cluded)

Maximum power output ....... 1 000 W × 1 (4 W) / 2 400 W

×1(1W)

Continuous power output ...500 W × 1 (at 14.4 V, 4 W,

20 Hz to 240 Hz, ≦ 1 % THD)

800 W × 1 (at 14.4 V, 2 W,

100 Hz, ≦ 1 % THD)

1 200 W × 1 (at 14.4 V, 1 W,

100 Hz, ≦ 1 % THD)

Load impedance ...................... 4 W (1 W to 8 W allowable)

Frequency response ............... 10 Hz to 240 Hz (+0 dB,

–3 dB)

Signal-to-noise ratio ............... 100 dB (IHF-A network)

Low pass filter:

Cut off frequency ........... 40 Hz to 240 Hz

Cut off slope ..................... –12 dB/oct

Bass boost:

Frequency .......................... 50 Hz

Level ..................................... 0 dB to 18 dB

Gain control:

RCA ...................................... 200 mV to 6.5 V

Speaker .............................. 0.8 V to 16 V

Maximum input level / impedance:

RCA ...................................... 6.5 V / 25 kW

<5707000012760V>14

Additional information

Speaker .............................. 16 V / 12 kW

CEA2006 Specifications

Power output ............................. 500 W RMS × 1 Channel (at

14.4 V, 4 W, 20 Hz to 240 Hz

and ≦ 1 % THD+N)

800 W RMS × 1 Channel (at

14.4 V, 2 W, 100 Hz and ≦ 1%

THD+N)

1 200 W RMS × 1 Channel

(at 14.4 V, 1 W, 100 Hz and ≦

1 % THD+N)

S/N ratio ....................................... 75 dBA (reference: 1 W into

4 W)

Notes

! Specifications and the design are subject to

modifications without notice.

! The average current consumption is nearly

the maximum current consumption by this

unit when an audio signal is input. Use this

value when working out total current con-

sumption by multiple power amplifiers.

<5707000012760V>15

Additional information

Nous vous remercions d’avoir acheté cet

appareil PIONEER

Pour garantir une utilisation correcte, lisez

bien ce mode d’emploi avant d’utiliser cet ap-

pareil. Il est particulièrement important que

vous lisiez et respectiez les indications AT-

TENTION et PRÉCAUTION de ce mode

d’emploi. Conservez-le dans un endroit sûr et

facilement accessible pour toute consultation

ultérieure.

Service après-vente des

produits Pioneer

Veuillez contacter le revendeur ou le distribu-

teur auprès duquel vous avez acheté cet appa-

reil pour le service après-vente (y compris les

conditions de garantie) ou pour toute autre in-

formation. Dans le cas où les informations né-

cessaires ne sont pas disponibles, veuillez

contacter les sociétés indiquées ci-dessous :

N’expédiez pas l’appareil pour réparation à

l’une des adresses figurant ci-dessous sans

avoir pris contact au préalable.

ÉTATS-UNIS ET CANADA

Pioneer Electronics (USA) Inc.

CUSTOMER SUPPORT DIVISION

P.O. Box 1760

Long Beach, CA 90801-1760

800-421-1404

Pour connaître les conditions de garantie, re-

portez-vous au document Garantie limitée qui

accompagne cet appareil.

Si vous rencontrez des

problèmes

En cas d’anomalie, consultez le distributeur

ou le service d’entretien agréé par Pioneer le

plus proche.

Visitez notre site Web

http://www.pioneerelectronics.com

au Canada

http://www.pioneerelectronics.ca

! Informez-vous sur les mises à jour disponi-

bles pour votre produit (telles que les mises

à jour du firmware).

! Enregistrez votre produit afin de recevoir

des notifications concernant les mises à

jour du produit, ainsi que pour sauvegarder

les détails de votre achat dans nos fichiers

en cas de perte ou de vol.

! Accédez aux modes d’emploi, aux informa-

tions relatives aux pièces de rechange et à

l’entretien, et à beaucoup d’autres

informations.

La protection de votre ouïe

est entre vos mains

Pour assurer le rendement optimal de votre

matériel et – plus important encore – la protec-

tion de votre ouïe, réglez le volume à un niveau

raisonnable. Pour ne pas altérer votre sens de

la perception, le son doit être clair mais ne

produire aucun vacarme et être exempt de

toute distorsion. Votre ouïe peut vous jouer

des tours. Avec le temps, votre système auditif

peut en effet s’adapter à des volumes supéri-

eurs, et ce qui vous semble un « niveau de

confort normal » pourrait au contraire être ex-

cessif et contribuer à endommager votre ouïe

de façon permanente. Le réglage de votre ma-

tériel à un volume sécuritaire AVANT que votre

ouïe s’adapte vous permettra de mieux vous

protéger.

CHOISISSEZ UN VOLUME SÉCURITAIRE :

! Réglez d’abord le volume à un niveau infé-

rieur.

! Montez progressivement le volume jusqu’à

un niveau d’écoute confortable ; le son doit

être clair et exempt de distorsions.

<5707000012760V>16

Avant de commencer

! Une fois que le son est à un niveau confor-

table, ne touchez plus au bouton du vo -

lume.

N’OUBLIEZ PAS DE RESPECTER LES

DIRECTIVES SUIVANTES :

! Lorsque vous montez le volume, assurez-

vous de pouvoir quand même entendre ce

qui se passe autour de vous.

! Faites très attention ou cessez temporaire-

ment l’utilisation dans les situations pou-

vant s’avérer dangereuses.

! N’utilisez pas des écouteurs ou un casque

d’écoute lorsque vous opérez un véhicule

motorisé ; une telle utilisation peut créer

des dangers sur la route et est illégale à de

nombreux endroits.

Quelques mots sur cet appareil

Ce produit est un amplificateur mono pour haut-

parleur d’extrêmes graves. Si les canaux L (gau-

che) et D (droit) sont tous les deux connectés à

l’entrée RCA de ce produit, la sortie sera combi-

née étant donné que ce produit est un amplifica-

teur mono.

Avant de connecter/

d’installer l’amplificateur

AVERTISSEMENT

! Les fentes et ouvertures du boîtier sont pré-

vues pour la ventilation afin de garantir un

fonctionnement fiable du produit et de le pro-

téger contre la surchauffe. Pour éviter tout

risque d’incendie, les ouvertures ne doivent ja-

mais être bloquées ou recouvertes d’objets

(tels que du papier, des tapis de sol, des chif-

fons).

! Cet appareil est utilisable sur des véhicules

équipés d’une batterie 12 V avec mise à la

masse du négatif. Vérifiez la tension de la bat-

terie avant l’installation dans des véhicules de

caravaning, des camions ou des bus.

! Lors de l’installation de cet appareil, veillez à

connecter d’abord le fil de masse. Assurez-

vous que le fil de masse est connecté correc-

tement aux parties métalliques de la carrosse-

rie du véhicule. Le fil de masse de cet appareil

doit être connecté indépendamment au véhi-

cule à l’aide de vis différentes. Si la vis du fil

de masse se desserre ou tombe, il peut en ré-

sulter un incendie, de la fumée ou un dysfonc-

tionnement.

! Assurez-vous de bien installer le fusible sur le

fil de la batterie.

! Utilisez toujours un fusible correspondant aux

caractéristiques spécifiées. L’utilisation d’un

fusible incorrect peut entraîner une sur-

chauffe et de la fumée, des dommages au ni-

veau du produit et des blessures, incluant des

brûlures.

! Vérifiez les connexions de l’alimentation et

des haut-parleurs en cas de rupture du fusible

du fil de batterie vendu séparément ou de

l’amplificateur. Déterminez la cause et résol-

vez le problème, puis remplacez le fusible par

un fusible identique.

! Installez toujours l’amplificateur sur une sur-

face plane. N’installez pas l’amplificateur sur

une surface qui n’est pas plane ou sur une

surface présentant une saillie. Ceci pourrait

entraîner un dysfonctionnement.

! Lors de l’installation de l’amplificateur, ne lais-

sez pas des pièces telles que des vis supplé-

mentaires se coincer entre l’amplificateur et

l’automobile. Ceci pourrait entraîner un dys-

fonctionnement.

! Ne laissez pas cet appareil entrer en contact

avec des liquides. Cela pourrait provoquer une

électrocution. Tout contact avec des liquides

pourrait aussi provoquer des dommages, de

la fumée et une surchauffe de l’appareil.

Les surfaces de l’amplificateur et des haut-

parleurs connectés peuvent également chauf-

fer et entraîner des brûlures mineures.

<5707000012760V>17

Avant de commencer

! En cas d’événement anormal, l’alimentation

de l’amplificateur est coupée de manière à évi-

ter tout dysfonctionnement de l’équipement.

Dans ce cas, coupez l’alimentation du sys-

tème et vérifiez les connexions de l’alimenta-

tion et des haut-parleurs. Si vous n’êtes pas

en mesure de déterminer la cause, veuillez

contacter votre revendeur.

! Déconnectez toujours la borne négative * de

la batterie préalablement, de manière à éviter

tout risque de choc électrique ou de court-cir-

cuit lors de l’installation.

! N’essayez pas de démontez ou de modifiez

cet appareil. Ceci pourrait provoquer un in-

cendie, une électrocution ou tout autre dys-

fonctionnement.

PRÉCAUTION

! Maintenez le niveau d’écoute à une valeur

telle que vous puissiez entendre les sons pro-

venant de l’extérieur.

! L’utilisation prolongée du système stéréo du

véhicule lorsque le moteur est à l’arrêt ou au

ralenti peut épuiser la batterie.

! Ce produit est évalué sous des conditions cli-

matiques modérées et tropicales conformé-

ment à la norme CEI 60065 sur les Appareils

audio, vidéo et appareils électroniques analo-

gues - Exigences de sécurité.

! Le symbole graphique

situé sur le

produit représente le courant continu.

! Connectez l’un des trois haut-parleurs d’extrê-

mes graves à l’amplificateur; 1 : un haut-par-

leur d’extrêmes graves avec une entrée

nominale de 300 W (GM-D8701 et GM-DX871) /

500 W (GM-D9701 et GM-DX971) ou plus et

une impédance de 4 W ; 2 : un haut-parleur

d’extrêmes graves avec une entrée nominale

de 500 W (GM-D8701 et GM-DX871) / 800 W

(GM-D9701 et GM-DX971) ou plus et une impé-

dance de 2 W ou 3 : un haut-parleur d’extrê-

mes graves avec une entrée nominale de

800 W (GM-D8701 et GM-DX871) / 1 200 W

(GM-D9701 et GM-DX971) ou plus et une impé-

dance de 1 W.

Si l’entrée nominale et l’impédance sont en

dehors des plages ci-dessus, le haut-parleur

d’extrêmes graves risque de prendre feu, de

dégager de la fumée ou d’être endommagé.

Quelques mots sur la fonction de

protection

Ce produit est doté d’une fonction de protection.

Lorsque ce produit détecte une anomalie, les

fonctions suivantes permettent de protéger le

produit et la sortie du haut-parleur.

! L’indicateur POWER/PROTECT devient rouge

et l’amplificateur se met hors service dans les

situations indiquées ci-dessous.

— Si la température à l’intérieur de l’amplifi-

cateur est trop élevée.

— Si une tension CC est appliquée à la borne

de sortie des haut-parleurs.

! L’indicateur POWER/PROTECT devient rouge

et le son de la sortie est coupé dans les situ-

ations indiquées ci-dessous.

— Si la borne de sortie des haut-parleurs et le

fil du haut-parleur sont en court-circuit.

Important (Numéro de série)

Le numéro de série se trouve au bas de cet appa-

reil. Pour votre sécurité et votre commodité, veil-

lez à noter ce numéro sur la carte de garantie

fournie.

<5707000012760V>18

Avant de commencer

Description de l’appareil

GM-D8701 et GM-DX871

Face avant

21 3 4

Face arrière

GM-D9701 et GM-DX971

Face avant

21 3 4

Face arrière

Si nécessaire, utilisez un tournevis plat pour

régler le commutateur.

1 Indicateur POWER/PROTECT

L’indicateur de mise sous tension s’allume

pour indiquer la mise sous tension.

! L’indicateur devient rouge en cas d’ano-

malie.

2 Commande GAIN (gain)

Si la sortie reste faible alors que le volume

du système stéréo du véhicule a été aug-

menté, tournez les commandes vers un ni-

veau plus faible. En cas de distorsion lors

de l’augmentation du volume du système

stéréo du véhicule, tournez les commandes

vers un niveau plus élevé.

! Procédez au réglage sur la position

NORMAL pour l’utilisation avec un sys-

tème stéréo de véhicule équipé d’une

sortie RCA (sortie standard de 500 mV).

Pour l’utilisation avec un système stéréo

de véhicule Pioneer équipé d’une sortie

RCA, dont la sortie maximale est de 4 V

ou plus, réglez le niveau en fonction de

celui de sortie du système stéréo du véhi-

cule.

! Procédez au réglage sur la position H

pour l’utilisation avec un système stéréo

de véhicule équipé d’une sortie de 4 V.

! Si la quantité de parasites est trop impor-

tante lors de l’utilisation des bornes d’en-

trée des haut-parleurs, tournez la

commande de gain à un niveau plus

élevé.

3 Commande de fréquence de coupure

LPF (filtre passe-bas)

Vous pouvez sélectionner une fréquence de

coupure de 40 Hz à 240 Hz.

4 Jack BASS BOOST REMOTE (télécom-

mande du niveau d’accentuation des gra-

ves)

En connectant la télécommande du niveau

d’accentuation des graves au jack de l’appa-

reil central, vous pourrez sélectionner le ni-

veau d’accentuation de graves entre 0 dB et

18 dB.

Pour des instructions sur la connexion de la

télécommande du niveau d’accentuation

des graves à l’amplificateur, reportez-vous à

Schéma de connexion.

Réglage correct du gain

! Fonction de protection incluse pour éviter

tout dysfonctionnement de l’appareil et/ou

des haut-parleurs lié à une sortie excessive

ou à une utilisation ou une connexion in-

correcte.

<5707000012760V>19

Réglage de l’appareil

! Lors de l’émission de sons à haut volume,

etc., cette fonction coupe l’émission pen-

dant quelques secondes. L’émission est ce-

pendant rétablie une fois le volume de

l’appareil central baissé.

! Une coupure de la sortie son peut indiquer

un réglage incorrect de la commande de

gain. Afin de garantir une émission sonore

continue lorsque le volume de l’appareil

central est élevé, réglez la commande de

gain de l’amplificateur à un niveau adapté

au niveau de sortie maximal de la sortie

préamp de l’appareil central de manière à

ce que le volume ne nécessite aucune mo -

dification et à ce que les sorties excessives

soient contrôlées.

! Le son de l’appareil est régulièrement

coupé alors que les réglages du gain et du

volume sont corrects. Dans de tels cas,

veuillez contacter le Centre d’entretien

agréé par Pioneer le plus proche.

Commande de gain de l’appareil

Niveau de préamp : 2 V (standard : 500 mV)

Niveau de préamp : 4 V

L’illustration ci-dessus représente le réglage

de gain NORMAL.

Relation entre le gain de

l’amplificateur et la puissance de

sortie de l’appareil central

Si le gain de l’amplificateur est augmenté de

manière incorrecte, les distorsions augmen-

tent sans que la puissance soit beaucoup plus

importante.

Forme de signal lors de l’émission à

volume élevé avec la commande de

gain de l’amplificateur

Si la forme de signal est distordue à cause

d’une sortie élevée, la puissance de sortie ne

sera que légèrement modifiée même en aug-

mentant le gain de l’amplificateur.

<5707000012760V>20

Réglage de l’appareil

Schéma de connexion

1 Fil de la batterie (vendu séparément)

! La longueur maximale du fil entre le fu-

sible et la borne positive + de la batterie

est de 30 cm.

! Pour connaître la taille du fil, reportez-

vous à Connexion de la borne d’alimenta-

tion. Le fil de la batterie, le fil de terre et

le fil de terre directe en option doivent

être de la même taille. Une fois toutes

les autres connexions à l’amplificateur

effectuées, connectez la borne du fil de

la batterie de l’amplificateur à la borne

positive + de la batterie.

2 Fusible 100 A (GM-D8701 et GM-DX871) / 150 A

(GM-D9701 et GM-DX971) (vendu séparément)

Chaque amplificateur doit être doté d’un fu-

sible distinct de 100 A (GM-D8701 et GM-

DX871) / 150 A (GM-D9701 et GM-DX971).

3 Borne positive +

4 Borne négative (*)

5 Batterie (vendue séparément)

6 Fil de terre, borne (vendu séparément)

Les fils de terre doivent être de la même taille

que le fil de la batterie.

À connecter au châssis ou à la carrosserie en

métal.

7 Système stéréo de véhicule avec jacks de sor-

tie RCA (vendu séparément)

8 Sortie externe

9 Fil de connexion avec prises RCA (vendu sépa-

rément)

a Amplificateur avec jacks d’entrée RCA (vendu

séparément)

b Télécommande du niveau d’accentuation des

graves

c Fil de la télécommande du niveau d’accentua-

tion des graves (5 m)

d Jack d’entrée RCA

e Jack de sortie RCA

f Fil de la télécommande du système (vendu sé-

parément)

Connectez la borne mâle du fil à la borne de

la télécommande du système stéréo du véhi-

cule. La borne femelle peut être connectée à

la prise de commande du relais de l’antenne

motorisée. Si le système stéréo du véhicule ne

dispose pas d’une borne de télécommande,

connectez la borne mâle à la borne d’alimen-

tation via le contact d’allumage.

g Bornes de sortie des haut-parleurs

Veuillez vous reporter à la section suivante

pour les instructions de connexion des haut-

parleurs. Reportez-vous à Connexions lors de

l’utilisation du fil d’entrée des haut-parleurs.

h Fusible 40 A × 2 (GM-D8701 et GM-DX871) /

40 A × 3 (GM-D9701 et GM-DX971)

i Face avant

j Face arrière

Avant de connecter

l’amplificateur

AVERTISSEMENT

! Fixez le câblage avec des serre-fils ou de la

bande adhésive. Pour protéger le câblage, en-

roulez les sections en contact avec des pièces

en métal dans du ruban adhésif.

<5707000012760V>21

Connexion des appareils

! Ne découpez jamais l’isolation de l’alimenta-

tion pour alimenter d’autres équipements. La

capacité en courant du fil est limitée.

PRÉCAUTION

! Ne raccourcissez jamais aucun fil, faute de

quoi le circuit de protection risque de fonc-

tionner de manière incorrecte.

! Ne câblez jamais le câble négatif du haut-par-

leur directement à la masse.

! Ne réunissez jamais ensemble les câbles né-

gatifs de plusieurs haut-parleurs.

! Si le fil de la télécommande du système de

l’amplificateur est connecté à la borne d’ali-

mentation via le contact d’allumage (12 V CC),

l’amplificateur reste sous tension que le sys-

tème stéréo du véhicule soit allumé ou non,

ce qui peut épuiser la batterie lorsque le mo -

teur est à l’arrêt ou au ralenti.

! Installez et positionnez le fil de batterie vendu

séparément aussi loin que possible des fils de

haut-parleurs.

Installez et positionnez le fil de batterie vendu

séparément, le fil de terre, les fils de haut-par-

leurs et l’amplificateur aussi loin que possible

de l’antenne, du câble d’antenne et du

syntoniseur.

Connexion des haut-parleurs

Cet amplificateur peut être connecté à deux

haut-parleurs en parallèle. Connectez les fils

des haut-parleurs en fonction du mode selon

l’illustration ci-dessous.

Précautions à prendre pour une

connexion parallèle

! Lorsque vous branchez deux haut-parleurs

en parallèle, assurez-vous que l’impédance

synthétique est comprise entre 1 W à8W

pour éviter que l’amplificateur ne prenne

feu, ne dégage de la fumée et/ou ne soit

endommagé.

! Lorsqu’il est connecté en parallèle avec

une impédance synthétique inférieure à

1 W, à savoir en condition de fonctionne-

ment normal, le son de cet amplificateur

peut automatiquement être coupé en cas

d’émission d’un son à volume élevé. Bais-

sez le volume jusqu’à ce que la fonction de

coupure du son soit annulée.

Lors de la connexion à un haut-parleur

Sortie des haut-parleurs

Lors de la connexion à deux haut-

parleurs

La sortie des deux haut-parleurs est identique

à celle d’un haut-parleur.

Sortie des haut-parleurs

<5707000012760V>22

Connexion des appareils

Connexions lors de

l’utilisation du fil d’entrée

des haut-parleurs

Connectez les fils de sortie des haut-parleurs

du système stéréo du véhicule à l’amplifica-

teur à l’aide du fil d’entrée des haut-parleurs

fourni, avec cordon RCA.

1 Système stéréo du véhicule

2 Sortie des haut-parleurs

3 Rouge : + droit

4 Noir : * droit

5 Noir : * gauche

6 Blanc : + gauche

7 Fil d’entrée des haut-parleurs avec cordon

RCA

Vers le jack d’entrée RCA de cet appareil

Remarques

! Si les fils d’entrée des haut-parleurs d’un ap-

pareil central sont connectés à cet amplifica-

teur, l’amplificateur se met automatiquement

en service lorsque l’appareil central est mis

en service. Lorsque l’appareil central est mis

hors service, l’amplificateur se met automati-

quement hors service. Cette fonction peut ne

pas fonctionner sur certains appareils cen-

traux. Dans ce cas, utilisez le fil d’une télé-

commande du système (vendu séparément).

Si plusieurs amplificateurs sont connectés de

manière synchrone, reliez l’appareil central et

tous les amplificateurs via le fil de la télécom-

mande du système.

! Connectez le fil de la télécommande du sys-

tème lorsque vous souhaitez mettre le sys-

tème stéréo du véhicule sous tension, et non

l’amplificateur.

! Cet amplificateur sélectionne automatique-

ment un mode de signal d’entrée entre le ni-

veau RCA et le niveau de haut-parleur en

détectant un signal d’entrée.

Connexions de bornes sans

soudure

! Etant donné que le fil se relâche dans le

temps, il doit être inspecté régulièrement et

resserré si nécessaire.

! Ne soudez et ne pliez pas les extrémités

des fils tordus.

! Lors du serrage, veillez à ne pas coincer la

gaine isolante du fil.

! Utilisez la clé hexagonale fournie pour ser-

rer et desserrer la vis de la borne de l’ampli-

ficateur et pour serrer fermement le fil.

Veillez à ne pas trop serrer la vis, faute de

quoi le fil pourrait être endommagé.

Connexion de la borne

d’alimentation

AVERTISSEMENT

Si le fil de la batterie n’est pas fermement fixé à la

borne à l’aide des vis de la borne, des risques de

surchauffe, d’anomalie de fonctionnement et de

blessures, brûlures mineures incluses, existent.

! Utilisez toujours le fil de la batterie et le fil

de terre recommandés, qui sont vendus sé-

parément. Connectez le fil de la batterie di-

rectement sur la borne positive (+) de la

batterie du véhicule et le fil de terre sur la

carrosserie du véhicule.

! La taille de fils recommandée (AWG : Ame-

rican Wire Gauge) est la suivante. Le fil de

la batterie, le fil de terre et le fil de terre di-

recte en option doivent être de la même

taille.

! Utilisez un fil de 8 AWG à 16 AWG pour les

haut-parleurs.

<5707000012760V>23

Connexion des appareils

Taille du fil de terre et du fil de batterie

Longueur du fil Taille du fil

moins de 3,6 m 6 AWG

moins de 6,4 m 4 AWG

1 Positionnez le fil de la batterie du

compartiment du moteur jusqu’àl’intérieur

du véhicule.

! Lors du perçage d’un trou de passage des

câbles dans la carrosserie du véhicule et le

passage d’un fil de la batterie à travers

celui-ci, veillez à ne pas créer un court-cir-

cuit du fil en l’endommageant avec les

bords coupants ou les bavures du trou.

Une fois toutes les autres connexions de l’am-

plificateur effectuées, connectez la borne du

fil de batterie de l’amplificateur à la borne po-

sitive + de la batterie.

1 Borne positive +

2 Fil de la batterie (vendu séparément)

La longueur maximale du fil entre le fusible

et la borne positive + de la batterie est de

30 cm.

3 Fusible 100 A (GM-D8701 et GM-DX871) /

150 A (GM-D9701 et GM-DX971) (vendu sé-

parément)

Chaque amplificateur doit être doté d’un fu-

sible distinct de 100 A (GM-D8701 et GM-

DX871) / 150 A (GM-D9701 et GM-DX971).

2 Utilisez une pince coupante ou un cou-

teau à lame rétractable pour dénuder l’ex-

trémité du fil de la batterie, connectez le fil

de terre et le fil de la télécommande afin

d’exposer environ 10 mm à l’extrémité de

chacun des fils, puis torsadez les extrémités

exposées des fils.

Torsadez

10 mm

3 Connectez les fils à la borne.

Fixez fermement les fils à l’aide des vis de la

borne.

1 Fil de la batterie

2 Borne d’alimentation

3 Fil de terre

4 Borne de terre

5 Fil de la télécommande du système

6 Borne de la télécommande du système

7 Vis de la borne

<5707000012760V>24

Connexion des appareils

Connexion des bornes de sortie

des haut-parleurs

1 Utilisez une pince coupante ou un cou-

teau à lame rétractable pour dénuder l’ex-

trémité des fils des haut-parleurs et

exposer environ 10 mm de fil, puis torsadez

le fil.

Torsadez

10 mm

2 Connectez les fils des haut-parleurs aux

bornes de sortie des haut-parleurs.

Fixez fermement les fils à l’aide des vis de la

borne.

1 Vis de la borne

2 Fils des haut-parleurs

3 Bornes de sortie des haut-parleurs

Avant d’installer

l’amplificateur

AVERTISSEMENT

! Afin de garantir une installation correcte, utili-

sez les pièces fournies de la manière indi-

quée. Si vous utilisez des pièces autres que

celles fournies, celles-ci risquent d’endomma-

ger des pièces internes de l’amplificateur ou

peuvent se desserrer, ce qui entraînerait l’arrêt

de l’amplificateur.

! Ne procédez pas à l’installation dans :

— Des emplacements où l’appareil peut bles-

ser le conducteur ou les passagers en cas

d’arrêt soudain du véhicule.

— Des emplacements où l’appareil peut

gêner le conducteur, tels que sur le sol de-

vant le siège du conducteur.

! Installez les vis autotaraudeuses de telle ma-

nière que la pointe des vis n’entre en contact

avec aucun fil. Cela est important pour éviter

toute coupure des fils par les vibrations du vé-

hicule, ce qui pourrait entraîner un incendie.

! Assurez-vous que les fils ne sont pas coincés

dans le mécanisme coulissant des sièges ou

ne touchent pas les jambes d’un passager,

car cela pourrait entraîner un court-circuit.

! Lorsque vous percez pour installer l’amplifica-

teur, vérifiez toujours qu’il n’y a aucune pièce

derrière le panneau et que tous les câbles et

équipements importants (conduites de carbu-

rant/freinage, câblage, par exemple) sont pro-

tégés des dommages.

PRÉCAUTION

! Afin de garantir une dissipation de la chaleur

correcte au niveau de l’amplificateur, vérifiez

les points suivants lors de l’installation :

— Laissez suffisamment de place au-dessus

de l’amplificateur pour permettre une ven-

tilation correcte.

— Ne couvrez pas l’amplificateur avec un

tapis de sol ou de la moquette.

! Placez les câbles à l’écart de tous les endroits

chauds, par exemple les sorties de chauffage.

<5707000012760V>25

Connexion des appareils Installation

! L’emplacement d’installation optimal varie en

fonction du modèle de véhicule. Fixez l’ampli-

ficateur à un emplacement suffisamment ri-

gide.

! Vérifiez toutes les connexions et tous les systè-

mes avant l’installation finale.

! Une fois l’amplificateur installé, vérifiez que la

roue de secours, le cric et les outils peuvent

facilement être retirés.

Fixation de la

télécommande du niveau

d’accentuation des graves

Fixez à l’aide de vis autotaraudeuses (3 mm ×

10 mm ) à un emplacement facilement acces-

sible tel que sous le tableau de bord.

Vis autotaraudeuses (3 mm × 10 mm )

Exemple d’installation sur

le tapis de sol ou le châssis

1 Placez l’amplificateur à l’emplacement

d’installation souhaité.

Insérez les vis autotaraudeuses fournies

(4 mm × 18 mm) dans les trous pour vis et ap-

puyez sur les vis à l’aide d’un tournevis de ma-

nière créer une empreinte de l’emplacement

des trous d’installation.

2 Percez des trous de 2,5 mm de diamètre

au niveau des empreintes, sur le sol ou di-

rectement sur le châssis.

3 Installez l’amplificateur à l’aide des vis

autotaraudeuses fournies (4 mm × 18 mm ).

1 Vis autotaraudeuses (4 mm × 18 mm )

2 Percez un trou de 2,5 mm de diamètre.

3 Tapis de sol ou châssis

4 Distance entre les trous : 229,5 mm (GM-

D8701 et GM-DX871) / 279,5 mm (GM-D9701

et GM-DX971)

5 Distance entre les trous : 191,5 mm

<5707000012760V>26

Installation

Caractéristiques techniques

GM-D8701 et GM-DX871

Tension d’alimentation ......... 14,4 V CC (10,8 V à 15,1 V

acceptable)

Mise à la masse ....................... Pôle négatif

Consommation électrique

..................................................... 22 A (4 W en alimentation en

continu)

Consommation électrique moyenne

..................................................... 2,4 A (4 W pour un canal)

3,6 A (2 W pour un canal)

5,7 A (1 W pour un canal)

Fusible .......................................... 40 A × 2

Dimensions (L x H x P) ......... 252 mm × 60 mm ×

215 mm

Poids .............................................. 2,7 kg

(fils de câblage non inclus)

Puissance de sortie maximale

..................................................... 600 W × 1 (4 W)/1600W×

1 (1 W)

Puissance de sortie continue

..................................................... 300 W × 1 (à 14,4 V, 4 W,

20 Hz à 240 Hz, ≦ 1 % DHT)

500 W × 1 (à 14,4 V, 2 W

100 Hz, ≦ 1 % DHT)

800 W × 1 (à 14,4 V, 1 W,

100 Hz, ≦ 1 % DHT)

Impédance de charge ........... 4 W (1 W à8W acceptable)

Réponse en fréquence .......... 10 Hz à 240 Hz (+0 dB,

–3 dB)

Rapport signal/bruit ............... 100 dB (réseau IHF-A)

Filtre passe-bas :

Fréquence de coupure

........................................... 40 Hz à 240 Hz

Pente de coupure .......... – 12 dB/octave

Accentuation des graves :

Fréquence ......................... 50 Hz

Niveau ................................. 0 dB à 18 dB

Commande de gain :

RCA ...................................... 200 mV à 6,5 V

Haut-parleur ..................... 0,8 V à 16 V

Niveau d’entrée maximal/impédance :

RCA ...................................... 6,5 V / 25 kW

Haut-parleur ..................... 16 V / 12 kW

Caractéristiques CEA2006

Puissance de sortie ................ 300 W eff. × 1 voie (à 14,4 V,

4 W, 20 Hz à 240 Hz et ≦ 1%

DHT+N)

500 W eff. × 1 voie (à 14,4 V,

2 W, 100 Hz et ≦ 1 % DHT

+N)

800 W eff. × 1 voie (à 14,4 V,

1 W, 100 Hz et ≦ 1 % DHT

+N)

Rapport S/B ................................ 75 dBA (référence : 1 W sur

4 W)

GM-D9701 et GM-DX971

Tension d’alimentation ......... 14,4 V CC (10,8 V à 15,1 V

acceptable)

Mise à la masse ....................... Pôle négatif

Consommation électrique

..................................................... 38 A (4 W en alimentation en

continu)

Consommation électrique moyenne

..................................................... 3,5 A (4 W pour un canal)

5,1 A (2 W pour un canal)

7,5 A (1 W pour un canal)

Fusible .......................................... 40 A × 3

Dimensions (L × H × P) ...... 302 mm × 60 mm ×

215 mm

Poids .............................................. 3,1 kg

(fils de câblage non inclus)

Puissance de sortie maximale

..................................................... 1 000 W × 1 (4 W) / 2 400 W

×1(1W)

Puissance de sortie continue

..................................................... 500 W × 1 (à 14,4 V, 4 W,

20 Hz à 240 Hz, ≦ 1 % DHT)

800 W × 1 (à 14,4 V, 2 W,

100 Hz, ≦ 1 % DHT)

1 200 W × 1 (à 14,4 V, 1 W,

100 Hz, ≦ 1 % DHT)

Impédance de charge ........... 4 W (1 W à8W acceptable)

Réponse en fréquence .......... 10 Hz à 240 Hz (+0 dB,

–3 dB)

Rapport signal/bruit ............... 100 dB (réseau IHF-A)

Filtre passe-bas :

Fréquence de coupure

........................................... 40 Hz à 240 Hz

Pente de coupure .......... – 12 dB/octave

<5707000012760V>27

Informations

complémentaires

Accentuation des graves :

Fréquence ......................... 50 Hz

Niveau ................................. 0 dB à 18 dB

Commande de gain :

RCA ...................................... 200 mV à 6,5 V

Haut-parleur ..................... 0,8 V à 16 V

Niveau d’entrée maximal/impédance :

RCA ...................................... 6,5 V / 25 kW

Haut-parleur ..................... 16 V / 12 kW

Caractéristiques CEA2006

Puissance de sortie ................ 500 W eff. × 1 voie (à 14,4 V,

4 W, 20 Hz à 240 Hz et ≦ 1%

DHT+N)

800 W eff. × 1 voie (à 14,4 V,

2 W, 100 Hz et ≦ 1 % DHT

+N)

1 200 W eff. × 1 voie (à

14,4 V, 1 W, 100 Hz et ≦ 1%

DHT+N)

Rapport S/B ................................ 75 dBA (référence : 1 W sur

4 W)

Remarques

! Les caractéristiques et la présentation peu-

vent être modifiées sans avis préalable.

! La consommation électrique moyenne corres-

pond quasiment à la consommation élec-

trique maximale de cet appareil lors de

l’entrée d’un signal audio. Utilisez cette valeur

lors du calcul de la consommation électrique

maximale de plusieurs amplificateurs.

<5707000012760V>28

Informations

complémentaires

<5707000012760V>29

Pioneer GM-DX971 Le manuel du propriétaire

Marque: Pioneer

Modèle: GM-DX971

Catégorie: Amplificateurs audio de voiture

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Pioneer GM-DX971 Owner's manual

Pioneer GM-DX971 Le manuel du propriétaire

Ce manuel convient également à

Pioneer GM-DX971 Le manuel du propriétaire

dans d''autres langues

Documents connexes