Pioneer GM-A5702 Le manuel du propriétaire

Marque: Pioneer

Modèle: GM-A5702

Taper: Le manuel du propriétaire

Ce manuel convient également à

GM-A3702

English

Français

BRIDGEABLE TWO-CHANNEL POWER AMPLIFIER

AMPLIFICATEUR DE PUISSANCE PONTABLE À DEUX CANAUX

GM-A5702

GM-A3702

Owner’s Manual

Mode d’emploi

5707000011330S <1>

PIONEER CORPORATION

28-8, Honkomagome 2-chome, Bunkyo-ku,

Tokyo 113-0021, JAPAN

PIONEER ELECTRONICS (USA) INC.

P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.

TEL: (800) 421-1404

PIONEER EUROPE NV

Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium/Belgique

TEL: (0) 3/570.05.11

PIONEER ELECTRONICS ASIACENTRE PTE. LTD.

2 Jalan Kilang Barat, #07-01, Singapore 159346

TEL: 65-6378-7888

PIONEER ELECTRONICS AUSTRALIA PTY. LTD.

5 Arco Lane, Heatherton, Victoria, 3202 Australia

TEL: (03) 9586-6300

PIONEER ELECTRONICS OF CANADA, INC.

340 Ferrier Street, Unit 2, Markham, Ontario L3R 2Z5, Canada

TEL: 1-877-283-5901

TEL: 905-479-4411

PIONEER ELECTRONICS DE MÉXICO S.A. de C.V.

Blvd.Manuel Ávila Camacho 138, 10 piso

Col.Lomas de Chapultepec, México, D.F. 11000

TEL: 52-55-9178-4270

FAX: 52-55-5202-3714

先鋒股份有限公司

台北市內湖區瑞光路407號8樓

電話： 886-(0)2-2657-3588

先鋒電子（香港）有限公司

香港九龍長沙灣道909號5樓

電話： 852-2848-6488

Tous droits de reproduction et de

traduction réservés.

<5707000011330S> UC

5707000011330S <2>

Thank you for purchasing this PIONEER

product

To ensure proper use, please read through this

manual before using this product. It is espe-

cially important that you read and observe

WARNINGs and CAUTIONs in this manual.

Please keep the manual in a safe and accessible

place for future reference.

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful interfer-

ence, and (2) this device must accept any inter-

ference received, including interference that

may cause undesired operation.

Information to User

Alteration or modifications carried out without

appropriate authorization may invalidate the

user’s right to operate the equipment.

Note

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference in a residential in-

stallation. This equipment generates, uses and

can radiate radio frequency energy and, if not in-

stalled and used in accordance with the instruc-

tions, may cause harmful interference to radio

communications. However, there is no guarantee

that interference will not occur in a particular in-

stallation. If this equipment does cause harmful

interference to radio or television reception,

which can be determined by turning the equip-

ment off and on, the user is encouraged to try to

correct the interference by one or more of the fol-

lowing measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment

and receiver.

- Connect the equipment into an outlet on a cir-

cuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV

technician for help.

After-sales service for

Pioneer products

Please contact the dealer or distributor from

where you purchased this unit for after-sales

service (including warranty conditions) or any

other information. In case the necessary infor-

mation is not available, please contact the

companies listed below:

Please do not ship your unit to the companies

at the addresses listed below for repair without

advance contact.

USA&CANADA

Pioneer Electronics (USA) Inc.

CUSTOMER SUPPORT DIVISION

P.O. Box 1760

Long Beach, CA 90801-1760

800-421-1404

For warranty information please see the Lim-

ited Warranty sheet included with this unit.

If you experience problems

Should this product fail to operate properly,

please contact your dealer or nearest author-

ized Pioneer Service Station.

Before you start

5707000011330S <3>

Visit our website

http://www.pioneerelectronics.com

in Canada

http://www.pioneerelectronics.ca

! Learn about product updates (such as firm-

ware updates) for your product.

! Register your product to receive notices

about product updates and to safeguard

purchase details in our files in the event of

loss or theft.

! Access owner’s manuals, spare parts infor-

mation, service information, and much

more.

The Safety of Your Ears is in

Your Hands

Get the most out of your equipment by playing

it at a safe level—a level that lets the sound

come through clearly without annoying blar-

ing or distortion and, most importantly, with-

out affecting your sensitive hearing. Sound

can be deceiving. Over time, your hearing

“comfort level” adapts to higher volumes of

sound, so what sounds “normal” can actually

be loud and harmful to your hearing. Guard

against this by setting your equipment at a

safe level BEFORE your hearing adapts.

ESTABLISH A SAFE LEVEL:

! Set your volume control at a low setting.

! Slowly increase the sound until you can

hear it comfortably and clearly, without dis-

tortion.

! Once you have established a comfortable

sound level, set the dial and leave it there.

BE SURE TO OBSERVE THE FOLLOWING

GUIDELINES:

! Do not turn up the volume so high that you

can’t hear what’s around you.

! Use caution or temporarily discontinue use

in potentially hazardous situations.

! Do not use headphones while operating a

motorized vehicle; the use of headphones

may create a traffic hazard and is illegal in

many areas.

Before connecting/

installing the amplifier

WARNING

! The use of a special red battery and ground

wire RD-223, available separately, is recom-

mended. Connect the battery wire directly to

the car battery positive terminal + and the

ground wire to the car body.

! This unit is for vehicles with a 12 V battery and

negative grounding. Before installing in re-

creational vehicles, trucks or buses, check the

battery voltage.

! When installing this unit, make sure to con-

nect the ground wire first. Ensure that the

ground wire is properly connected to metal

parts of the car’s body. The ground wire of the

one of this unit must be connected to the car

separately with different screws. If the screw

for the ground wire loosens or falls out, it

could result in fire, generation of smoke or

malfunction.

! Always use a fuse of the rating prescribed.

The use of an improper fuse could result in

overheating and smoke, damage to the pro-

duct and injury, including burns.

! Check the connections of the power supply

and speakers if the fuse of the separately sold

battery wire or the amplifier fuse blows. Deter-

mine and resolve the cause, then replace the

fuse with and identical equivalent.

! Always install the amplifier on a flat surface.

Do not install the amplifier on a surface that

is not flat or on a surface with a protrusion.

Doing so could result in malfunction.

Before you start

5707000011330S <4>

! When installing the amplifier, do not allow

parts such as extra screws to get caught be-

tween the amplifier and the automobile.

Doing so could cause malfunction.

! Do not allow this unit to come into contact

with liquids. Electrical shock could result.

Also, damage to this unit, smoke, and over-

heating could result from contact with liquids.

The surfaces of the amplifier and any attached

speakers may also heat up and cause minor

burns.

! In the event of any abnormality, the power

supply to the amplifier is cut off to prevent

equipment malfunction. If this occurs, switch

the system power off and check the power

supply and speaker connections. If you are un-

able to determine the cause, please contact

your dealer.

! Always disconnect the negative * terminal of

the battery beforehand to avoid the risk of

electric shock or short circuit during installa-

tion.

! Do not attempt to disassemble or modify this

unit. Doing so may result in fire, electric

shock or other malfunction.

CAUTION

! Always keep the volume low enough to hear

outside sounds.

! Extended use of the car stereo while the en-

gine is at rest or idling may exhaust the bat-

tery.

! This product is evaluated in moderate and tro-

pical climate condition under the Audio, video

and similar electronic apparatus - Safety re-

quirements, IEC 60065.

! The graphical symbol

placed on the

product means direct current.

About the protection function

This product has protection function. When this

product detects something abnormal, the follow-

ing functions will operate to protect the product

and speaker output.

! The power indicator will turn off and the am-

plifier will shut down in the situations outlined

below.

— If the speaker output terminal and speaker

wire are short-circuited.

— If a DC voltage is applied to the speaker

output terminal.

! The amplifier will reduce the power output if

the temperature inside the amplifier gets

high. If the temperature gets too high, the

power indicator will turn off, and the amplifier

will shut down.

Important (Serial number)

The serial number is located on the bottom of

this unit. For your own security and convenience,

be sure to record this number on the enclosed

warranty card.

Note

Before installing this unit in your vehicle, refer to

the illustration below and remove the tag (GM-

A5702 only).

Do not use the parts you have removed (screws

etc.) when installing the unit in your vehicle.

Before you start

5707000011330S <5>

What’s what

GM-A5702

Front side

Rear side

GM-A3702

Front side

Rear side

To adjust the switch, use a flathead screwdri-

ver if needed.

1 LPF (low-pass filter) switch

Switch the settings based on the connected

speaker.

! When the Subwoofer is connected:

Select ON. This eliminates high range

frequency and outputs low range fre-

quency.

! When the full range speaker is con-

nected:

Select OFF. OFF outputs the entire fre-

quency range.

2 FREQ (cut off frequency) control

Cut off frequency selectable from 40 Hz to

500 Hz if the LPF select switch is set to ON.

3 BASS BOOST (bass boost level control)

switch

You can select a bass boost level from 0 dB,

6 dB and 12 dB.

4 GAIN (gain) control

If the output remains low, even when the car

stereo volume is turned up, turn the con-

trols to a lower level. If distortion occurs

when the car stereo volume is turned up,

turn these controls to a higher level.

! For use with an RCA equipped car stereo

(standard output of 500 mV), set to the

NORMAL position. For use with an RCA

equipped Pioneer car stereo, with maxi-

mum output of 4 V or more, adjust level

to match that of the car stereo output.

! For use with an RCA equipped car stereo

with output of 4 V, set to the HIGH posi-

tion.

! If you hear too much noise when using

the speaker input terminals, turn the

gain control to higher level.

5 Power indicator

The power indicator lights up to indicate

power ON.

Setting the unit

5707000011330S <6>

Setting gain properly

! Protective function included to prevent

malfunction of the unit and/or speakers

due to excessive output, improper use or

improper connection.

! When outputting high volume sound etc.,

this function cuts off the output for a few

seconds as a normal function, but output

is restored when the volume of the head

unit is turned down.

! A cut in sound output may indicate impro-

per setting of the gain control. To ensure

continuous sound output with the head

unit at a high volume, set amplifier gain

control to a level appropriate for the preout

maximum output level of the head unit, so

that volume can remain unchanged and to

control excess output.

! Despite correct volume and gain settings,

the unit sound still cuts out periodically. In

such cases, please contact the nearest

authorized Pioneer Service Station.

Gain control of this unit

Preout level: 4 V

Preout level: 2 V

(Standard: 500 mV)

Above illustration shows NORMAL gain set-

ting.

Relationship between amplifier gain

and head unit output power

If amplifier gain is raised improperly, this will

simply increase distortion, with little increase

in power.

Signal waveform when outputting at

high volume using amplifier gain

control

If the signal waveform is distorted due to high

output, even if the amplifier gain is raised, the

output power will change only slightly.

Setting the unit

5707000011330S <7>

Connection diagram

1 Special red battery wire

RD-223 (sold separately)

After completing all other amplifier connec-

tions, finally connect the battery wire terminal

of the amplifier to the positive + battery term-

inal.

2 Ground wire (Black)

RD-223 (sold separately)

Connect to metal body or chassis.

3 Car stereo with RCA output jacks (sold sepa-

rately)

4 External output

5 Connecting wire with RCA pin plugs (sold se-

parately)

6 Speaker input terminal (use a connector in-

cluded)

Please see the following section for speaker

connection instructions. Refer to Connections

when using the speaker input wire.

7 RCA input jack

8 System remote control wire (sold separately)

Connect male terminal of this wire to the sys-

tem remote control terminal of the car stereo.

The female terminal can be connected to the

auto-antenna relay control terminal. If the car

stereo lacks a system remote control terminal,

connect the male terminal to the power term-

inal via the ignition switch.

9 Speaker output terminals

Please see the following section for speaker

connection instructions. Refer to Connecting

the speakers.

a Fuse 30 A × 2 (GM-A5702) / 25 A × 1 (GM-

A3702)

b Fuse (30 A) × 2

c Grommet

d Rear side

e Front side

Connecting the units

5707000011330S <8>

Before connecting the

amplifier

WARNING

! Secure the wiring with cable clamps or adhe-

sive tape. To protect the wiring, wrap sections

in contact with metal parts in adhesive tape.

! Never cut the insulation of the power supply

to feed power to other equipment. Current ca-

pacity of the wire is limited.

CAUTION

! Never shorten any wires, the protection circuit

may malfunction.

! Never wire the speaker negative cable directly

to ground.

! Never band together multiple speaker’s nega-

tive cables.

! If the system remote control wire of the ampli-

fier is connected to the power terminal via the

ignition switch (12 VDC), the amplifier will re-

main on with the ignition whether the car

stereo is on or off, which may exhaust battery

if the engine is at rest or idling.

! Install and route the separately sold battery

wire as far as possible from the speaker wires.

Install and route the separately sold battery

wire, ground wire, speaker wires and the am-

plifier as far away as possible from the anten-

na, antenna cable and tuner.

About bridged mode

! Do not install or use this amplifier by wiring

speakers rated at 4 W (or lower) in parallel to

achieve a 2 W (or lower) bridged mode (Dia-

gram B).

Amplifier damage, smoke, and overheating

could result from improper bridging. The am-

plifier surface could also become hot to the

touch and minor burns could result.

To properly install or use a bridged mode and

achieve a 4 W load, wire two 8 W speakers in

parallel with Left + and Right * (Diagram A)

or use a single 4 W speaker.

In addition, refer to the speaker instruction

manual for information on the correct connec-

tion procedure.

! For any further enquiries, contact your local

authorized Pioneer dealer or customer

service.

About suitable

specification of speaker

Ensure speakers conform to the following

standards, otherwise there is a risk of fire,

smoke or damage. Speaker impedance is 2 W

to 8 W for stereo connection, or 4 W to 8 W for

monaural and other bridge connection.

Connecting the units

5707000011330S <9>

Subwoofer

Speaker channel Power

Two-channel output

Nominal input:

Min. 150 W (GM-A5702)

Min. 60 W (GM-A3702)

One-channel output

Nominal input:

Min. 480 W (GM-A5702)

Min. 190 W (GM-A3702)

Other than subwoofer

Speaker channel Power

Two-channel output

MAX input:

Min. 300 W (GM-A5702)

Min. 170 W (GM-A3702)

One-channel output

MAX input:

Min. 1000 W (GM-A5702)

Min. 500 W (GM-A3702)

Connecting the speakers

The speaker output mode can be two-channel

(stereo) or one-channel (mono). Connect the

speaker leads to suit the mode according to

the figures shown below.

Two-channel output (Stereo)

1 Speaker (Left)

2 Speaker (Right)

One-channel output

1 Speaker (Mono)

Connecting the units

5707000011330S <10>

Connections when using

the speaker input wire

Connect the car stereo speaker output wires

to the amplifier using the supplied speaker

input wire.

! Do not connect both the RCA input and the

speaker input at the same time.

1 Car Stereo

2 Speaker output

3 White/black: Left *

4 White: Left +

5 Gray/black: Right *

6 Gray: Right +

7 Speaker input connector

To speaker input terminal of this unit.

Note

If speaker input wires from a headunit are con-

nected to this amplifier, the amplifier will automa-

tically turn on when the headunit is turned on.

When the headunit is turned off, the amplifier

turns off automatically. This function may not

work with some headunits. In such cases, make

sure that the Left channel is connected correctly.

If the function still does not work, please use a

system remote control wire (sold separately). If

multiple amplifiers are to be connected together

synchronously, connect the head unit and all am-

plifiers via the system remote control wire.

Connecting the power

terminal

The use of a special red battery and ground

wire RD-223 (sold separately) is recom-

mended. Connect the battery wire directly to

the car battery positive terminal + and the

ground wire to the car body.

WARNING

If the battery wire is not securely fixed to the term-

inal using the terminal screws, there is a risk of

overheating, malfunction and injury, including

minor burns.

1 Route battery wire from engine com-

partment to the vehicle interior.

! When drilling a cable pass-hole into the ve-

hicle body and routing a battery wire thor-

ough it, take care not to short-circuit the

wire damaging it by the cut edges or burrs

of the hole.

After completing all other amplifier connec-

tions, finally connect the battery wire terminal

of the amplifier to the positive + battery term-

inal.

1 Positive + terminal

2 Engine compartment

3 Vehicle interior

4 Fuse (30 A) × 2

5 Insert the O-ring rubber grommet into the

vehicle body.

6 Drill a 14 mm (1/2 in.) hole into the vehicle

body.

Connecting the units

5707000011330S <11>

2 Twist the battery wire, ground wire

and system remote control wire.

Twist

3 Attach lugs to wire ends.

Use pliers, etc., to crimp lugs to wires.

1 Lug (sold separately)

2 Battery wire

3 Ground wire

4 Connect the wires to the terminal.

Fix the wires securely with the terminal

screws.

1 System remote control terminal

2 Ground terminal

3 Power terminal

4 Terminal screws

5 Battery wire

6 Ground wire

7 System remote control wire

Connecting the speaker

output terminals

1 Use wire cutters or a utility knife to

strip the end of the speaker wires to ex-

pose about 10 mm (3/8 in.) of wire and

then twist the wire.

Twist

2 Attach lugs to wire ends.

Use pliers, etc., to crimp lugs to wires.

1 Lug (sold separately)

2 Speaker wire

3 Connect the speaker wires to the

speaker output terminals.

Fix the speaker wires securely with the term-

inal screws.

Connecting the units

5707000011330S <12>

1 Terminal screws

2 Speaker wires

3 Speaker output terminals

Before installing the amplifier

WARNING

! To ensure proper installation, use the supplied

parts in the manner specified. If any parts

other than those supplied are used, they may

damage internal parts of the amplifier, or be-

come loose causing the amplifier to shut

down.

! Do not install in:

— Places where it could injure the driver or

passengers if the vehicle stops suddenly.

— Places where it may interfere with the dri-

ver, such as on the floor in front of the dri-

ver’s seat.

! Install tapping screws in such a way that the

screw tip does not touch any wire. This is im-

portant to prevent wires from being cut by vi-

bration of the car, which can result in fire.

! Make sure that wires do not get caught in the

sliding mechanism of the seats or touch the

legs of a person in the vehicle as short-circuit

may result.

! When drilling to install the amplifier, always

confirm no parts are behind the panel and

protect all cables and important equipment

(e.g. fuel/brake lines, wiring) from damage.

CAUTION

! To ensure proper heat dissipation of the ampli-

fier, ensure the following during installation:

— Allow adequate space above the amplifier

for proper ventilation.

— Do not cover the amplifier with a floor mat

or carpet.

! Protection function may activate to protect the

amplifier against overheating due to installa-

tion in locations where sufficient heat cannot

be dissipated, continuous use under high-vo-

lume conditions, etc. In such cases, the am-

plifier reduces the power output or shuts

down until it has cooled to a certain desig-

nated temperature.

! Place all cables away from hot places, such

as near the heater outlet.

Connecting the units Installation

5707000011330S <13>

! The optimal installation location differs de-

pending on the car model. Secure the ampli-

fier at a sufficiently rigid location.

! Check all connections and systems before

final installation.

! After installing the amplifier, confirm that the

spare tire, jack and tools can be easily re-

moved.

Example of installation on

the floor mat or chassis

1 Place the amplifier in the desired instal-

lation location.

Insert the supplied tapping screws (4 mm ×

18 mm (1/8 in. × 3/4 in.)) into the screw holes

and push on the screws with a screwdriver so

they make an imprint where the installation

holes are to be located.

2 Drill 2.5 mm (1/8 in.) diameter holes at

the imprints either on the carpet or directly

on the chassis.

3 Install the amplifier with the use of

supplied tapping screws (4 mm × 18 mm

(1/8 in. × 3/4 in.)).

1 Tapping screws (4 mm × 18 mm (1/8 in. ×

3/4 in.))

2 Drill a 2.5 mm (1/8 in.) diameter hole.

3 Floor mat or chassis

4 Hole-to-hole distance: 343 mm (13-1/2 in.)

(GM-A5702) / 233 mm (9-1/8 in.) (GM-A3702)

5 Hole-to-hole distance: 195 mm (7-5/8 in.)

(GM-A5702) / 160 mm (6-1/4 in.) (GM-

A3702)

Installation

5707000011330S <14>

Specifications

GM-A5702

Power source ............................. 14.4 V DC (10.8 V to 15.1 V

allowable)

Grounding system ................... Negative type

Current consumption ............ 36 A (at continuous power,

4 W)

Average current consumption

..................................................... 9.5 A (4 W for two channels)

15.5 A (4 W for one channel)

Fuse ................................................ 30 A × 2

Dimensions (W × H × D) ... 356 mm × 60 mm ×

215 mm

(14 in. × 2-3/8 in. × 8-1/2 in.)

Weight .......................................... 2.2 kg (4.9 lbs)

(Leads for wiring not in-

cluded)

Maximum power output ....... 300 W × 2 (4 W) / 500 W × 2

(2 W) / 1000 W TOTAL

(BRIDGE)

Continuous power output ...150W × 2 (at 14.4 V, 4 W,

20 Hz to 20 kHz, ≦ 1.0 % THD

+N)

480 W × 1 (at 14.4 V, 4 W

BRIDGE 1 kHz, ≦ 1.0 % THD

+N)

240 W × 2 (at 14.4 V, 2 W,

1 kHz, ≦ 1.0 % THD+N)

Load impedance ...................... 4 W (2 W to 8 W allowable)

Frequency response ............... 10 Hz to 70 kHz (+0 dB,

–3 dB)

Signal-to-noise ratio ............... 96 dB (IHF-A network)

Distortion ..................................... 0.05 % (10 W, 1 kHz)

Low pass filter:

Cut off frequency ........... 40 Hz to 500 Hz

Cut off slope ..................... –12 dB/oct

Bass boost:

Frequency .......................... 50 Hz

Level ..................................... 0 dB/6 dB/12 dB

Gain control:

RCA ...................................... 0.3 V to 6.5 V

Speaker .............................. 3.0 V to 26 V

Maximum input level / impedance:

RCA ...................................... 6.5 V / 22 kW

Speaker .............................. 26 V / 16 kW

CEA2006 Specifications

Power output ............................. 150 W RMS × 2 Channels

(at 14.4 V, 4 W and ≦ 1%

THD+N)

S/N ratio ....................................... 75 dBA (reference: 1 W into

4 W)

GM-A3702

Power source ............................. 14.4 V DC (10.8 V to 15.1 V

allowable)

Grounding system ................... Negative type

Current consumption ............ 14.5 A (at continuous power,

4 W)

Average current consumption

..................................................... 4 A (4 W for two channels)

6.5 A (4 W for one channel)

Fuse ................................................ 25 A × 1

Dimensions (W × H × D) ... 246 mm × 60 mm ×

180 mm

(9-5/8 in. × 2-3/8 in. ×

7-1/8 in.)

Weight .......................................... 1.4 kg (3.1 lbs)

(Leads for wiring not in-

cluded)

Maximum power output ....... 170 W × 2 (4 W) / 250 W × 2

(2 W) / 500 W TOTAL

(BRIDGE)

Continuous power output ...60 W × 2 (at 14.4 V, 4 W,

20 Hz to 20 kHz, ≦ 1.0 % THD

+N)

190 W × 1 (at 14.4 V, 4 W

BRIDGE 1 kHz, ≦ 1.0 % THD

+N)

95 W × 2 (at 14.4 V, 2 W,

1 kHz, ≦ 1.0 % THD+N)

Load impedance ...................... 4 W (2 W to 8 W allowable)

Frequency response ............... 10 Hz to 70 Hz (+0 dB,

–3 dB)

Signal-to-noise ratio ............... 95 dB (IHF-A network)

Distortion ..................................... 0.05 % (10 W, 1 kHz)

Low pass filter:

Cut off frequency ........... 80 Hz

Cut off slope ..................... –12 dB/oct

Gain control:

RCA ...................................... 0.3 V to 6.5 V

Speaker .............................. 3.0 V to 26 V

Additional information

5707000011330S <15>

Maximum input level / impedance:

RCA ...................................... 6.5 V / 22 kW

Speaker .............................. 26 V / 16 kW

CEA2006 Specifications

Power output ............................. 60 W RMS × 2 Channels (at

14.4 V, 4 W and ≦ 1 % THD

+N)

S/N ratio ....................................... 78 dBA (reference: 1 W into

4 W)

Notes

! Specifications and the design are subject to

modifications without notice.

! The average current consumption is nearly

the maximum current consumption by this

unit when an audio signal is input. Use this

value when working out total current con-

sumption by multiple power amplifiers.

Additional information

5707000011330S <16>

Nous vous remercions d’avoir acheté cet

appareil PIONEER

Pour garantir une utilisation correcte, lisez

bien ce mode d’emploi avant d’utiliser cet ap-

pareil. Il est particulièrement important que

vous lisiez et respectiez les indications AT-

TENTION et PRÉCAUTION de ce mode

d’emploi. Conservez-le dans un endroit sûr et

facilement accessible pour toute consultation

ultérieure.

Service après-vente des

produits Pioneer

Veuillez contacter le revendeur ou le distribu-

teur auprès duquel vous avez acheté cet appa-

reil pour le service après-vente (y compris les

conditions de garantie) ou pour toute autre in-

formation. Dans le cas où les informations né-

cessaires ne sont pas disponibles, veuillez

contacter les sociétés indiquées ci-dessous :

N’expédiez pas l’appareil pour réparation à

l’une des adresses figurant ci-dessous sans

avoir pris contact au préalable.

ÉTATS-UNIS ET CANADA

Pioneer Electronics (USA) Inc.

CUSTOMER SUPPORT DIVISION

P.O. Box 1760

Long Beach, CA 90801-1760

800-421-1404

Pour connaître les conditions de garantie, re-

portez-vous au document Garantie limitée qui

accompagne cet appareil.

Si vous rencontrez des

problèmes

En cas d’anomalie, consultez le distributeur

ou le service d’entretien agréé par Pioneer le

plus proche.

Avant de commencer

5707000011330S <17>

Visitez notre site Web

http://www.pioneerelectronics.com

au Canada

http://www.pioneerelectronics.ca

! Informez-vous sur les mises à jour disponi-

bles pour votre produit (telles que les mises

à jour du firmware).

! Enregistrez votre produit afin de recevoir

des notifications concernant les mises à

jour du produit, ainsi que pour sauvegarder

les détails de votre achat dans nos fichiers

en cas de perte ou de vol.

! Accédez aux modes d’emploi, aux informa-

tions relatives aux pièces de rechange et à

l’entretien, et à beaucoup d’autres

informations.

La protection de votre ouïe

est entre vos mains

Pour assurer le rendement optimal de votre

matériel et – plus important encore – la protec-

tion de votre ouïe, réglez le volume à un niveau

raisonnable. Pour ne pas altérer votre sens de

la perception, le son doit être clair mais ne

produire aucun vacarme et être exempt de

toute distorsion. Votre ouïe peut vous jouer

des tours. Avec le temps, votre système auditif

peut en effet s’adapter à des volumes supéri-

eurs, et ce qui vous semble un « niveau de

confort normal » pourrait au contraire être ex-

cessif et contribuer à endommager votre ouïe

de façon permanente. Le réglage de votre ma-

tériel à un volume sécuritaire AVANT que votre

ouïe s’adapte vous permettra de mieux vous

protéger.

CHOISISSEZ UN VOLUME SÉCURITAIRE :

! Réglez d’abord le volume à un niveau infé-

rieur.

! Montez progressivement le volume jusqu’à

un niveau d’écoute confortable ; le son doit

être clair et exempt de distorsions.

! Une fois que le son est à un niveau confor-

table, ne touchez plus au bouton du vo-

lume.

N’OUBLIEZ PAS DE RESPECTER LES

DIRECTIVES SUIVANTES :

! Lorsque vous montez le volume, assurez-

vous de pouvoir quand même entendre ce

qui se passe autour de vous.

! Faites très attention ou cessez temporaire-

ment l’utilisation dans les situations pou-

vant s’avérer dangereuses.

! N’utilisez pas des écouteurs ou un casque

d’écoute lorsque vous opérez un véhicule

motorisé ; une telle utilisation peut créer

des dangers sur la route et est illégale à de

nombreux endroits.

Avant de commencer

5707000011330S <18>

Avant de connecter/

d’installer l’amplificateur

ATTENTION

! L’utilisation d’un fil de terre RD-223 et d’un fil

de batterie rouge spécial, disponibles séparé-

ment, est recommandée. Connectez le fil de la

batterie directement sur la borne positive +

de la batterie du véhicule et le fil de terre sur

la carrosserie du véhicule.

! Cet appareil est utilisable sur des véhicules

équipés d’une batterie 12 V avec mise à la

masse du négatif. Vérifiez la tension de la bat-

terie avant l’installation dans des véhicules de

caravaning, des camions ou des bus.

! Lors de l’installation de cet appareil, veillez à

connecter d’abord le fil de masse. Assurez-

vous que le fil de masse est connecté correc-

tement aux parties métalliques de la carrosse-

rie du véhicule. Le fil de masse de cet appareil

doit être connecté indépendamment au véhi-

cule à l’aide de vis différentes. Si la vis du fil

de masse se desserre ou tombe, il peut en ré-

sulter un incendie, de la fumée ou un dysfonc-

tionnement.

! Utilisez toujours un fusible correspondant aux

caractéristiques spécifiées. L’utilisation d’un

fusible incorrect peut entraîner une sur-

chauffe et de la fumée, des dommages au ni-

veau du produit et des blessures, incluant des

brûlures.

! Vérifiez les connexions de l’alimentation et

des haut-parleurs en cas de rupture du fusible

du fil de batterie vendu séparément ou de

l’amplificateur. Déterminez la cause et résol-

vez le problème, puis remplacez le fusible par

un fusible identique.

! Installez toujours l’amplificateur sur une sur-

face plane. N’installez pas l’amplificateur sur

une surface qui n’est pas plane ou sur une

sur face présentant une saillie. Ceci pourrait

entraîner un dysfonctionnement.

! Lors de l’installation de l’amplificateur, ne lais-

sez pas des pièces telles que des vis supplé-

mentaires se coincer entre l’amplificateur et

l’automobile. Ceci pourrait entraîner un dys-

fonctionnement.

! Ne laissez pas cet appareil entrer en contact

avec des liquides. Cela pourrait provoquer une

électrocution. Tout contact avec des liquides

pourrait aussi provoquer des dommages, de

la fumée et une surchauffe de l’appareil.

Les surfaces de l’amplificateur et des haut-

parleurs connectés peuvent également chauf-

fer et entraîner des brûlures mineures.

! En cas d’événement anormal, l’alimentation

de l’amplificateur est coupée de manière à évi-

ter tout dysfonctionnement de l’équipement.

Dans ce cas, coupez l’alimentation du sys-

tème et vérifiez les connexions de l’alimenta-

tion et des haut-parleurs. Si vous n’êtes pas

en mesure de déterminer la cause, veuillez

contacter votre revendeur.

! Déconnectez toujours la borne négative * de

la batterie préalablement, de manière à éviter

tout risque de choc électrique ou de court-cir-

cuit lors de l’installation.

! N’essayez pas de démontez ou de modifiez

cet appareil. Ceci pourrait provoquer un in-

cendie, une électrocution ou tout autre dys-

fonctionnement.

PRÉCAUTION

! Maintenez le niveau d’écoute à une valeur

telle que vous puissiez entendre les sons pro-

venant de l’extérieur.

! L’utilisation prolongée du système stéréo du

véhicule lorsque le moteur est à l’arrêt ou au

ralenti peut épuiser la batterie.

! Ce produit est évalué sous des conditions cli-

matiques modérées et tropicales conformé-

ment à la norme CEI 60065 sur les Appareils

audio, vidéo et appareils électroniques analo-

gues - Exigences de sécurité.

! Le symbole graphique

situé sur le

produit représente le courant continu.

Avant de commencer

5707000011330S <19>

Quelques mots sur la fonction de

protection

Ce produit est doté d’une fonction de protection.

Lorsque ce produit détecte une anomalie, les

fonctions suivantes permettent de protéger le

produit et la sortie du haut-parleur.

! L’indicateur de mise sous tension s’éteint et

l’amplificateur se mettra hors service dans les

situations indiquées ci-dessous.

— Si la borne de sortie des haut-parleurs et le

fil du haut-parleur sont en court-circuit.

— Si une tension CC est appliquée à la borne

de sortie des haut-parleurs.

! L’amplificateur réduira la puissance de sortie

si la température à l’intérieur de l’amplifica-

teur est élevée. Si la température est trop éle-

vée, l’indicateur de mise sous tension s’éteint

et l’amplificateur se met hors service.

Important (Numéro de série)

Le numéro de série se trouve au bas de cet appa-

reil. Pour votre sécurité et votre commodité, veil-

lez à noter ce numéro sur la carte de garantie

fournie.

Remarque

Avant d’installer cet appareil dans votre véhicule,

reportez-vous à l’illustration ci-après et retirez l’é-

tiquette (GM-A5702 uniquement).

N’utilisez pas les pièces que vous avez retirées

(vis, etc.) lors de l’installation de l’appareil dans

votre véhicule.

Description de l’appareil

GM-A5702

Face avant

Face arrière

GM-A3702

Face avant

Face arrière

Si nécessaire, utilisez un tournevis plat pour

régler le commutateur.

1 Commutateur LPF (filtre passe-bas)

Basculez les réglages en fonction du haut-

parleur connecté.

! Lorsque le haut-parleur d’extrêmes gra-

ves est connecté :

Sélectionnez ON. Cela supprime les fré-

quences élevées et émet à basse fré-

quence.

! Lorsque le haut-parleur pleine gamme

est connecté :

Avant de commencer Réglage de l’appareil

5707000011330S <20>

La page charge ...

Pioneer GM-A5702 Le manuel du propriétaire

Marque: Pioneer

Modèle: GM-A5702

Taper: Le manuel du propriétaire

Ce manuel convient également à

GM-A3702

Télécharger le PDF

rapport

dans d''autres langues

English: Pioneer GM-A5702 Owner's manual

Pioneer GM-A5702 Le manuel du propriétaire

Ce manuel convient également à

Pioneer GM-A5702 Le manuel du propriétaire

dans d''autres langues

Documents connexes