Craftsman MXEVBE176560 Heavy Duty Wet Dry Vacuum Manuel utilisateur

Part No. SP7091 Printed in Mexico

INSTRUCTION MANUAL | GUIDE D’UTILISATION | MANUAL DE INSTRUCCIONES

IF YOU HAVE QUESTIONS OR COMMENTS, CONTACT US.

POUR TOUTE QUESTION OU TOUT COMMENTAIRE, NOUS CONTACTER.

SI TIENE DUDAS O COMENTARIOS, CONTÁCTENOS.

20 GALLON (75 Liter)

WET/DRY VAC WITH CART

ASPIRATEUR DE LIQUIDES ET DE POUSSIÈRES

DE 75 Litres (20 GALLONS) AVEC CHARIOT

ASPIRADORA PARA MOJADO/SECO

DE 75 Litros (20 GALONES) CON CARRITO

CMXEVBE176560

1-888-331-4569 WWW.CRAFTSMAN.COM

!

DANGER: Indicates a hazardous situation which, if not avoided, will result in death or serious

injury.

WARNING: Indicates a hazardous situation which, if not avoided, could result in death or serious

injury.

CAUTION: Indicates a hazardous situation which, if not avoided, may result in minor or moderate

injury.

(Used without word) Indicates a safety related message.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage.

!

1 Metal Handle

2 Accessory Storage Bag

3 Carry Handle

4 Power Cord Wrap

5 ON/OFF Switch

6 Hose Clips (2)

7 Powerhead Assembly

8 Vac Inlet

9 Dust Drum

10 Caster Foot w/Storage (2)

11 Casters (2)

12 Drain

13 Cart Wheels (2)

14 Power Cord

15 Drum Latches (2)

16 Blowing Port

2

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk

of personal injury or property damage.

Components

If you have any questions or comments about this or

any product, call CRAFTSMAN toll free at:

1-888-331-4569.

WARNING: Read all safety

warnings and all instructions. Failure to follow the

warnings and instructions may result in electric shock,

fire and/or serious injury.

WARNING: Never modify the

product or any part of it. Damage or personal injury

could result.

WARNING: To reduce the risk of

injury, read the instruction manual.

!

Fig. A

13

16

12

11

10

9

8

7

2

3

4

5

6

1

14

15

!

3

IMPORTANT SAFETY INSTRUCTIONS

• Read and understand this manual and all labels on the

Vac before operating.

• Use only as described in this manual.

• Do not leave Vac running while unattended - you may fail

to notice important signs indicating abnormal operation

such as loss of suction, debris/liquid exiting exhaust, or

abnormal motor noises. Immediately stop using Vac if you

notice these signs.

• Do not leave Vac when plugged in. Unplug from outlet

when not in use and before servicing.

• Sparks inside the motor can ignite flammable vapors or

dust. To reduce the risk of fire or explosion, do not use near

combustible liquids, gases, or dusts, such as gasoline or

other fuels, lighter fluid, cleaners, oil-based paints, natural

gas, coal dust, magnesium dust, grain dust, aluminum dust,

or gun powder.

• Do not vacuum anything that is burning or smoking, such as

cigarettes, matches, or hot ashes.

• To avoid the risk of self-ignition of drum debris, empty drum

after each use. Combustible materials, such as rags or saw

dust containing stain or urethane, can be sources of such

overheating.

• Do not vacuum drywall dust, cold fireplace ash, or other fine

dusts with standard filter. These may pass through the filter

and be exhausted back into the air. Use a fine dust filter

instead.

• To reduce the risk of inhaling toxic vapors, do not vacuum or

use near toxic or hazardous materials.

• This Wet/Dry Vac is not intended for use by persons

(including children) with reduced physical, sensory, or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety.

• To reduce the risk of electric shock, do not expose to rain or

allow liquid to enter motor compartment. Store indoors.

• Do not allow to be used as a toy. Close attention is

necessary when used by or near children.

• Do not use with a torn filter or without the filter

installed except when vacuuming liquids as described

in this manual. Dry debris ingested by the impeller may

damage the motor or be exhausted into the air.

• Turn off Vac before unplugging.

• To reduce the risk of injury from accidental starting,

unplug power cord before changing or cleaning filter.

• Do not unplug by pulling on cord. To unplug, grasp the

plug, not the cord.

• Do not use with damaged cord, plug, or other parts.

If your Vac is not working as it should, has missing parts,

has been dropped, damaged, left outdoors, or dropped

into water, call customer service at 1-888-331-4569

(Mexico 001-881-331-4569).

• Do not handle plug, switch, or the Vac with wet hands.

• Do not pull or carry by cord, use cord as handle, close a

door on cord, or pull cord around sharp edges or corners.

Do not run Vac over cord. Keep cord away from heated

surfaces.

• Use only extension cords that are rated for outdoor

use. Extension cords in poor condition or too small in

wire size can pose fire and shock hazards. To reduce

the risk of these hazards, be sure the cord is in good

condition and that liquid does not contact the connection.

Do not use an extension cord with conductors smaller

than 1,3 mm2 (16 AWG) in size.

• This Vac is double-insulated, eliminating the need

for a separate grounding system. Use only identical

replacement parts. Read the instructions for Servicing

Double-Insulated Wet/Dry Vacs.

• Do not put any object into ventilation openings. Do not

vacuum with any ventilation openings blocked; keep

free of dust, lint, hair, or anything that may reduce air

flow.

• Keep hair, loose clothing, fingers, and all parts of body

away from openings and moving parts.

• To reduce the risk of falls, use extra care when cleaning

on stairs.

• To reduce the risk of back injury or falls, do not lift a Vac

that is heavy with liquid or debris. Partially empty by

scooping debris or draining liquid.

• To reduce the risk of personal injury or damage to Vac,

use only CRAFTSMAN recommended accessories.

• When using as a blower:

- Direct air discharge only at work area.

- Do not direct air at bystanders.

- Keep children away when blowing.

- Do not use blower for any job except blowing dirt and

debris.

- Do not use as a sprayer.

• To reduce the risk of eye injury, wear safety eyewear.

The operation of any utility Vac or blower can result in

foreign objects being blown into the eyes, which can

result in severe eye damage.

• To reduce the risk of being struck by, or pulled down

by, a rolling Vac, block the casters when using on any

uneven or sloped surface.

WARNING:

To reduce the risk of fire, electric shock, or injury:

!

When using this Vac, always follow basic safety

precautions including the following:

4

Observe the following warnings that appear on the motor

housing of your Vac:

DOUBLE INSULATED - GROUNDING NOT REQUIRED.

WHEN SERVICING USE ONLY IDENTICAL

REPLACEMENT PARTS.

CAUTION:

• To reduce the risk of hearing damage, wear ear

protectors when using for an extended time or

in a noisy area.

• For dusty operations, wear dust mask.

• Static shocks are common when the relative

humidity of the air is low. Vacuuming fine

debris with your Vac can deposit static charge

on the hose or Vac. To reduce the frequency of

static shocks in your home or when using this

Vac, add moisture to the air with a humidifier.

Section PageSection Page

Important Safety Instructions.......................2-4

Introduction ...................................... 4

Carton Contents ................................... 5

Installation ......................................6-9

Drum/Wheel Assembly ........................... 6

Metal Handle Assembly........................... 7

Accessory Storage Bag Assembly ................... 7

Hose Clips Assembly ............................. 8

Carry Handle Assembly ........................... 8

Powerhead Assembly ............................. 8

Insert Hose...................................... 9

Accessory Storage ................................ 9

Hose Storage .................................... 9

Cord Storage .................................... 9

Operation ....................................10-12

Polarized Plug ..................................10

Power Switch ...................................10

Vacuuming Dry Materials ........................10

Vacuuming Liquids..............................11

Emptying the Drum .............................11

Moving the Wet/Dry Vac .........................12

Muffler / Diffuser................................12

Blowing Feature ................................12

Maintenance.................................. 13-15

Filter ..........................................13

Removal and Installation of Qwik Lock Filter™.......13

Filter Installation................................13

Filter Bag ......................................14

Filter Bag Installation ............................14

Filter Bag Removal ..............................14

Filter Cleaning..................................15

Cleaning a Dry Filter.............................15

Cleaning a Wet Filter ............................15

Cleaning and Disinfecting the Wet/Dry Vac .........15

Casters ........................................15

Storage........................................15

Service / Repair Parts...........................16-18

Servicing Double Insulated Wet/Dry Vacs. ............16

Warranty ........................................19

This Wet/Dry Vac with Cart is intended for house-hold use.

It may be used for vacuuming of wet or dry media and may

be used as a Blower.

Read this Instruction Manual to familiarize yourself with

the product features and to understand the specific usage

of your new Wet/Dry Vac.

SAVE THESE INSTRUCTIONS

INTRODUCTION

TABLE OF CONTENTS

WARNING:

• For your own safety, read and understand Instruction

Manual.

• Do not run unattended.

• Do not pick up hot ashes, coals, flammable,

combustible/self-igniting, toxic, or other hazardous

materials.

• Do not use around explosive liquids or vapors.

!

WARNING:

To reduce the risk of electric shock - do not expose to

rain - store indoors.

!

FREE WARNING LABEL REPLACEMENT: If your warning

labels become illegible or are missing, call 1-888-331-4569

for a free replacement.

Fig. B

Key Description Qty.

A Vac Assembly 1

B Carry Handle 1

C Hose Clips 2

D Hose 1

E Caster Foot with Storage 2

F Foot Wheel, Right 1

G Foot Wheel, Left 1

H Shaft 1

I Accessory Storage Bag 1

J 8” (20 cm) Wheels 2

K Metal Handle 1

L Disposable Filter Bag 1

M Utility Nozzle 1

N Wet Nozzle 1

O Car Nozzle 1

P Crevice Tool 1

Q Extension Wands 2

R Diffuser 1

S Loose Parts Bag 1

1. 2” (5 cm) Casters 2

2. 1/2” (50 mm) Cap Nuts 2

3. Wheel Caps 2

4. #10 x 1-3/4” (25 mm) Screws 4

5. Instruction Manual 1

5

Remove entire contents of carton. Check each item against

the Carton Contents List.

If any parts are damaged or missing, immediately

call customer service at 1-888-331-4569

(Mexico 001-881-331-4569).

Phillips Screwdriver

Tools Required:

CARTON CONTENTS (Fig. B)

Mallet

Hammer

Q

K

E

1

2

3

4

5

S

J

I

G

F

D

C

B

R

A

H

O

N

P

M

L

Fig. F

6

Drum/Wheel Assembly

Do not assemble Wet/Dry Vac until you have all the parts.

Rear Wheel Feet Assembly (Fig. C):

1. Insert the Left Rear Wheel Foot and the Right Rear

Wheel Foot into the bottom of Drum (opposite side

of the Drain). Check to make sure Axle Holes align.

Light taps with a Mallet or Hammer may be needed to

fully seat both Wheel Feet.

Rear Wheel

Foot (Left)

Drain

Drum

Rear Wheel Foot

(Right)

Align

Axle Holes

INSTALLATION

Fig. C

Rear Wheel Feet Assembly (Fig. D):

2. Insert the Two Caster Feet into the bottom of Drum

(Close to the Drain). Light taps with a Mallet or

Hammer may be needed to fully seat both Caster

Feet.

Drain

Front

Caster

Foot

Drum

Front

Caster

Foot

Fig. D

Fig. E

Hardware Assembly (Fig. E):

3. Install (4) #10 x 1-3/4” (25 mm) Screws into the Holes

on each of the Rear Wheel Feet and Front Caster Feet,

securing them to the bottom of the Drum. Tighten

Screws until just snug. Do not over tighten as this may

tend to deform the Feet.

Front

Caster

Foot

Drain

#10 x 1-3/4" (25 mm)

Screw (4)

Rear Wheel

Foot

Axle & Wheel Assembly (Fig. F):

4. Installing Cap Nut

a. Place Cap Nut on end of Axle.

b. Tap gently with Hammer until fully seated.

c. Place the Wheel on the Axle with smooth portion of

Wheel facing outward.

5. Slide open end of Axle through Left Rear Wheel Foot

Hole. Slide all the way through the Hole in the Right

Rear Wheel Foot. Light taps with a Mallet may be

required to fully insert Axle.

6. Install Second Wheel onto Axle with smooth portion of

Wheel facing outward.

7. Install the Second Cap Nut. Tap gently until Cap Nut is

firmly seated.

NOTE: Smooth side of the

wheel to the outside.

Rear Wheel Foot

(Right)

Drain

Axle

w/Wheel

Rear Wheel

Foot (Left)

Open

End

Cap

Nut

7

Fig. G

Wheel Cap Assembly (Fig. G):

8. Using a Rubber Mallet or Hammer, gently tap the

Wheel Cap onto the Right Wheel until the Wheel Cap

is firmly seated onto the Wheel. This is required on

both Left and Right Wheels.

Caster Ball Assembly (Fig. H):

9. Insert the Caster Stem into the Socket of the Two Front

Caster Feet.

10. Push on the Caster until the Ball on the Caster Stem is

inserted all the way into the Socket. You will be able

to hear the Ball snap into the Socket and the Caster will

swivel easily when positioning is correct.

Fig. H

Socket

Caster Stem

Caster Ball

Metal Handle Assembly (Fig. I)

Press and hold Release Buttons while installing Metal

Handle into Drum Handle Receptacles.

NOTE: An audible snap of Release Buttons indicates

successful engagement of the Metal Handle.

Fig. I

Removing Metal Handle

Press and hold the Release Buttons. While firmly pushing

in on the Release Buttons, pull Metal Handle upwards to

remove.

Accessory Storage Bag Assembly (Fig. J)

Install Accessory Storage Bag by wrapping the Five Storage

Bag Straps around the Metal Handle and snap each Strap

in place.

Fig. J

Mallet

Wheel

Cap

Release Buttons

Accessory

Storage Bag

Strap (5)

Handle

Accessory

Storage Bag

Snaps

8

Fig. K

Hose Clips Assembly (Fig. K)

1. Align the Hose Clips in the recessed areas on the

Powerhead Assembly.

2. Insert Screw and tighten to fasten the Hose Clips to the

Powerhead Assembly.

NOTE: The Hose Clip has a Screwdriver Notch for ease of

assembly.

Powerhead Assembly (Fig. M)

1. Line up front (label side) of Powerhead Assembly with

Vac Inlet Port, located on the front of the Drum.

NOTE: Powerhead Assembly must be aligned with Drum

for proper attachment.

2. Place Powerhead Assembly on top of Drum.

3. Be sure Powerhead Assembly completely covers the

top of the Drum so leakage does not occur.

4. Press down on the Powerhead Latches to securely

attach the Powerhead Assembly to the Drum.

5. To remove the Powerhead Assembly, first unplug

the unit from the electrical outlet. Then lift up on the

Powerhead Assembly Latches and remove from Drum.

Fig. M

Hose

Clip

Powerhead

Assembly

Notch

Screw

Fig. L

Carry Handle Assembly (Fig. L)

1. Place the Carry Handle on the Wet/Dry Vac Powerhead

Assembly.

2. Tighten Two Screws to assemble the Carry Handle on

the Powerhead Assembly.

Screws

Carry

Handle

Powerhead

Assembly

Powerhead

Assembly

Lid

Latches

Vac

Inlet

Label

9

Fig. N

Insert Hose (Fig. N)

1. Insert the Locking End of the Hose Assembly into the

Vac Inlet Port. The Hose should snap into place.

2. To remove the Hose from the Vac, press the Release

Button and pull the Hose out of the Vac Inlet Port.

Fig. O

Accessory Storage (Fig. O)

Your Accessories may be stored in the Caster Feet, Storage

Locations on the Powerhead Assembly or in the Accessory

Storage Bag.

Fig. P

Hose Storage (Fig. P)

The Hose may also be stored by wrapping it around the

Powerhead Assembly and securing it into the Hose Clips.

Fig. Q

Cord Storage (Fig. Q)

Wrap the Power Cord around the Carry Handle/Power Cord

Wrap located on the Powerhead Assembly Carry Handle.

Snap the Power Cord into the Cord Clip to secure.

Vac Inlet

Release

Button

Hose

Powerhead

Assembly

Storage for

Accessories

Storage Bag

Caster Feet Storage

for Accessories

Hose Clips

Hose

Powerhead

Assembly

Carry Handle/

Power Cord

Wrap

Cord

Clip

10

Vacuuming Dry Materials

1. The Filter must always be in correct position to reduce

the risk of leaks and possible damage to Vac.

2. When using your Vac to pick up very fine dust, it will

be necessary for you to empty the Vac Drum and clean

the Filter at more frequent intervals to maintain peak

Vac performance. Quick Lock™ Filter plus a Filter

Bag is recommended for improved Fine Dust Vac

performance.

NOTE: A dry Filter is necessary to pick up dry material.

If you use your Vac to pick up dust when the Filter is wet,

the Filter will clog quickly and be very difficult to clean.

Polarized Plug

To reduce the risk of electric shock, this Vac has a Polarized

Plug (one blade is wider than the other). This Plug will

fit in a Polarized Outlet only one way. If the Plug does not

fit fully in the Outlet, reverse the Plug. If it still does not fit,

contact a qualified electrician to install the proper Outlet.

Do not change the Plug in any way.

Power Switch (Fig. R)

After you Plug the Power Cord into the Outlet, turn the Unit

on by pushing the Switch from position “O” to position “l”.

The symbols used on the Switch Actuator are International

“On & Off” Symbols:

= OFF = ON

Fig. R

ON/OFF

Switch

OPERATION

WARNING:

To reduce the risk of electric shock or injury:

• Do not leave Vac running while unattended -

you may fail to notice important signs indicating

abnormal operation such as loss of suction,

debris/liquid exiting the exhaust, or abnormal

motor noises. Immediately stop using Vac if you

notice these signs.

• Do not leave Vac plugged in when not in use.

• Do not continue running when float has cut off

suction.

• Sparks inside the motor can ignite airborne

flammables. Do not operate Vac near

flammable liquids or in areas with flammable

gases, vapors, or explosive/airborne dust.

Flammable liquids, gases, and vapors include:

lighter fluid, solvent-type cleaners, oil-based

paints, gasoline, alcohol, and aerosol sprays.

Explosive dusts include: coal, magnesium,

aluminum, grain, and gun powder.

• Do not vacuum up explosive dusts, flammable

liquids, or hot ashes.

• Do not leave sawdust or rags with stain or

polyurethane residue inside Vac. Empty drum

after picking up these potentially self-heating

materials.

CAUTION:

To reduce the risk of hearing damage, wear ear

protectors when using the Vac/Blower for an extended

time or in a noisy area.

• Do not expose to rain or allow liquid to enter

motor compartment. Store indoors.

• Do not handle plug, switch, or Vac with wet

hands.

• Unplug Vac before servicing. If your Vac is not

working as it should, has missing parts, has

been dropped, damaged, left outdoors, or

dropped into water, call customer service at

1-888-331-4569 (Mexico 001-881-331-4569).

• When using an extension cord, use only

outdoor-rated cords that are in good condition.

Do not allow the connection to come into contact

with liquid.

WARNING:

To reduce the risk of fire, explosion, or

damage to Vac

!

1. When picking up small amounts of liquid the Filter

may be left in place.

2. When picking up large amounts of liquid we

recommend that the Filter be removed. If the Filter

is not removed, it will become saturated and misting

may appear in the exhaust.

3. After using the Vac to pick up liquids, the Filter must

be dried to reduce the risk of possible mildew and

damage to the Filter.

4. When the liquid in the Drum reaches a predetermined

level, the Float mechanism will rise automatically to

cut off air-flow. When this happens, turn off the Vac,

unplug the Power Cord, and empty the Drum. You

will know that the Float has risen because Vac airflow

ceases and the Motor noise will become higher in

pitch, due to increased Motor Speed.

IMPORTANT: To reduce the risk of damage to the Vac

do not run Motor with Float in raised position.

1. Remove the Powerhead Assembly. Pull Latches to

release from the Drum.

2. Lift the Powerhead Assembly up and away from the

Drum.

3. Lay Powerhead Assembly upside down on a clean area

while emptying the Drum.

4. Dump the Drum contents into the proper waste

disposal container.

5. The Vac comes equipped with a Drain, simply

unscrew the Drain Cap and lift the opposite side

slightly to empty the Drum.

Vacuuming Liquids Emptying the Drum (Fig. S)

11

Fig. S

Powerhead

Assembly

Lid

Latches

Drum

Drain

WARNING:

Do not operate without filter cage and float,

as they prevent liquid from entering the impeller and

damaging the motor. For dry material pick-up,

do not operate without the filter in place to reduce the

risk of damage to the motor.

WARNING:

To reduce the risk of fire or explosion, do not vacuum

flammable or combustible liquids, gases or dust.

!

WARNING:

To reduce the risk of injury from accidental starting,

unplug power cord before emptying the drum.

!

WARNING:

To reduce the risk of back injury or falls, do not lift a

Vac heavy with liquid or debris. Scoop or drain enough

contents out to make the Vac light enough to lift

comfortably.

!

Should it become necessary to pick the Vac up to move

it, use the Carry Handle and/or the Dust Drum Handles.

NOTE: Do not move Vac by the Powerhead Latches.

To maneuver the Vac, use the Metal Handle and/or the

Carry Handle.

Moving the Wet/Dry Vac (Fig. T)

Fig. T

Your Vac features a Blowing Port. It can blow sawdust

and other debris. Follow the steps below to use your Vac

as a Blower.

1. Locate Blowing Port of your Vac, located at the back of

the Powerhead Assembly.

2. Insert the Locking End of the Hose Assembly into the

Vac Blowing Port. The Hose should snap into place.

To remove the Hose from the Vac, press the Release

Button in the Hose Assembly and pull the Hose out of

the Vac Inlet Port.

3. (Optional) Attach Extension Wand to opposite end of

Hose, then place the Car Nozzle on the Wand.

4. Turn Vac on and you are ready to use your Vac as a

Blower.

Blowing Feature (Fig. V)

Fig. V

12

Fig. U

Muffler / Diffuser (Fig. U)

Insert the Locking End of the Muffler / Diffuser into the

Blowing Port of the Vac. The Muffler / Diffuser should snap

into place.

The Muffler / Diffuser suppresses motor noise and diffuses

the exhaust air and can be used while vacuuming indoors

or outdoors.

Muffler / Diffuser

Muffler/Diffuser

Release Button

(Locking End)

Vac Blowing Port

WARNING:

Always wear safety eyewear complying with ANSI Z87.1

(or in Canada, CSA Z94.3) before using as a blower.

!

WARNING:

To reduce the risk of injury to bystanders, keep them

clear of blowing debris.

!

CAUTION:

Wear a dust mask if blowing creates dust which might

be inhaled.

!

CAUTION:

To reduce the risk of hearing damage, wear ear

protectors when using the Vac / Blower for an extended

time or in a noisy area.

!

Metal Handle

Carry

Handle

Dust Drum

Handles (2)

Powerhead

Latches (2)

Swivel End

Of Hose

Extension

Wand (Optional)

Car Nozzle

(Optional)

Locking

Hose End

Blowing

Port

13

MAINTENANCE Fig. W

NOTE: This Filter is made of high quality paper designed

to stop very small particles of dust. The Filter can be used

for wet or dry pick up. Handle the Filter carefully when

removing to install or clean. Creases in the Filter pleats

may occur from installation but creases will not affect the

performance of the Filter.

IMPORTANT: To reduce the risk of damage to the Blower

Wheel and Motor, always reinstall the Filter before using

the Vac for dry material pickup.

Filter Removal

1. Hold the Filter Tabs of the Qwik Lock™ Filter in each

hand.

2. With one thumb on the Qwik Lock™ Stud, which

protrudes through the integrated Filter Plate, lift up

on the Filter Tabs while pushing down on the Stud.

3. This action will cause the Filter to release from the

Filter Cage. Slide Filter off Cage.

Removal and Installation of

the Qwik Lock™ Filter (Fig. W)

NOTE: Failure to properly seat the bottom Gasket could

result in debris bypassing the Filter.

Filter Installation

1. Carefully slide the Qwik Lock™ Filter over the

Filter Cage and press down on the outside edge of

the Filter until the Rubber Gasket on the bottom

of the Filter seats securely around the base of the

Filter Cage and against the Powerhead Assembly.

2. Align the small Center Hole in the top of the Filter over

the Qwik Lock™ Stud on the Filter Cage. Press firmly

on top of the Filter near the Stud to allow the Filter to

snap over the Ball on the end of the Stud. The Filter is

now attached.

Filter

Qwik Lock™

Stud

Rubber

Gasket at

Bottom of

Filter

PUSH

DOWN

PULL

UP

Filter

Tabs (2)

Integrated Filter Plate

with Center Hole

PULL

UP

Filter

Cage

Powerhead

Assembly

WARNING:

To reduce the risk of injury from accidental starting,

unplug power cord before changing or cleaning filter.

!

WARNING:

Do not operate without a filter cage and float, as

they prevent liquid from entering the impeller and

damaging the motor.

!

Fig. Y

14

Filter Bag Installation (Fig. X)

A Filter Bag may be used in place of or in addition to the

Qwik Lock™ Cartridge Filter.

NOTE: See Repair Parts List for Part Number.

NOTE: When picking up dry debris a Filter Bag or

Cartridge Filter must be properly installed.

1. Filter Bag to be used to pick up dry debris only.

2. Correct positioning of Cardboard Collar is required to

assure proper seal.

3. Locate two Ribs on Inlet Tube, inside Drum.

4. Slide Cardboard Collar onto Inlet Tube and position

Cardboard Collar between the two Ribs.

5. With the Cardboard Collar securely installed, unfold

and position Filter Bag inside Drum.

Filter Bag Removal (Fig. Y)

1. Slide Cardboard Collar toward center of Vac Drum.

2. Remove Filter Bag from Vac Drum and discard.

3. Install new Filter Bag.

Filter Bag

WARNING:

To avoid health hazards from vapors or dust,

do not vacuum toxic, carcinogenic or other hazardous

materials such as asbestos, arsenic, barium, beryllium,

lead, pesticides or other health endangering materials.

!

Unfolded

Filter Bag

Drum

Cardboard

Collar

Fig. X

Inlet Tube

Cardboard

Collar

Filter Bag

Ribs (2)

Drum

CAUTION:

To avoid spilled debris, when picking up heavy or sharp

material, monitor bag volume and do not overfill.

!

15

Filter Cleaning

Your Filter should be cleaned often to maintain peak Vac

performance.

Cleaning A Dry Filter

1. Some removal of dry debris can be accomplished

without removing the Filter from the Vac. Slap your

hand on top of the Powerhead Assembly while the Vac

is turned OFF.

2. For best cleaning results due to accumulated dust,

clean the Filter in an open area. Cleaning SHOULD be

done outdoors and not in the living quarters.

3. After Filter removal from Vac, remove the dry debris

by gently tapping Filter against the inside wall of your

Dust Drum. The debris will loosen and fall.

4. For thorough cleaning of dry Filter with fine dust

(no debris), run water through it as described under

“Cleaning A Wet Filter”.

Cleaning A Wet Filter

After Filter is removed, run water through the Filter from a

hose or spigot. Take care that water pressure from the hose is

not strong enough to damage Filter.

IMPORTANT: After cleaning, check the Filter for tears or

small holes. Tears and holes in the Filter can cause debris and

dust to be blown from the Vac. Do not use a Filter with holes

or tears. Replace immediately.

Allow the Filter to dry before reinstalling and storing the Vac

or picking up dry debris.

Cleaning and Disinfecting the

Wet/Dry Vac

To keep your Wet/Dry Vac looking its best, clean the outside

with a cloth dampened with warm water and mild soap.

To clean the Drum:

1. Dump debris out.

2. Wash Drum thoroughly with warm water and mild

soap.

3. Wipe out with dry cloth.

Before prolonged storage or as needed (i.e., waste water pick

up) the Drum should be disinfected.

To disinfect the Drum:

1. Pour 1 gallon (4 L) of water and 1 teaspoon (5 mL)

chlorine bleach into the Drum.

2. Let solution stand for 20 minutes, carefully swishing

every few minutes, making sure to wet all inside surfaces

of the Drum.

3. Empty Drum after 20 minutes. Rinse with water until

bleach smell is gone. Allow Drum to dry completely

before sealing the Motor on the Drum.

Casters

If your Casters are noisy, you may put a drop of oil on the

Roller Shaft to make them quieter.

Storage

Before storing your Vac, the Drum should be emptied

and cleaned. The Power Cord should be wrapped around

the Carry Handle. The Hose Assembly should be stored as

described in this manual. Accessories should be kept in

the same area as the Vac so they can be readily available.

The Vac should be stored indoors.

WARNING:

To assure product SAFETY and RELIABILITY, any other

maintenance, repairs and adjustments should be

performed by Authorized Service Centers, always using

CRAFTSMAN replacement parts.

!

16

SERVICE / REPAIR PARTS

Key No. Part No. Description

1 841579-1 Switch

2 510701 Top Handle & Hardware (2 screws)

3 510706 Motor Cover with Labels

4 829719-17 Cord with Terminal

5 841364-1 Duct, Exhaust

6 820563-4 Screw, Pan Hd Tp “AB” 10 x 3/4” (19 mm) Ser.

7 819260-13 Lead Assembly

8 510379 Motor Assembly

9 818961 Spacer

10 818413 Blower Wheel

11 315534-1 Washer

12 826817 Nut, Hex Flange 5/16 -18

13 510582 Hose Clip Assembly with Screws

14 510567 Lid / Lid Assembly

15 840321 Collector

16 820563-5 Screw, Pan Hd Tp “AB” 10 x 1-1/4” (31 mm) Ser.

17 823201-2 Filter Cage Assembly

18 CMXZVBE38754 Replacement Filter

19 CMXZVBE38749 Disposable Filter Bag

20 CMXZVBE38630 Utility Nozzle

21 CMXZVBE38620 Car Nozzle

22 CMXZVBE38621 Wet Nozzle

23 CMXZVBE37035 Crevice Tool

24 CMXZVBE38660 Diffuser

25 CMXZVBE38763 Hose Assembly

26 CMXZVBE38606 Extension Wand

27 SP7091 Instruction Manual

WARNING: SERVICING OF DOUBLE-INSULATED WET/DRY VAC

In a double-insulated Wet/Dry Vac, two systems of insulation are provided instead of grounding. No grounding means

is provided on a double-insulated appliance, nor should a means for grounding be added. Servicing a double-insulated

Wet/Dry Vac requires extreme care and knowledge of the system, and should be done only by qualified service personnel.

Replacement parts for a double-insulated Wet/Dry Vac must be identical to the parts they replace. Your double-insulated

Wet/Dry Vac is marked with the words “DOUBLE INSULATED” and the symbol (square within a square) may also

be marked on the appliance.

To reduce the risk of injury, unplug power cord before servicing the Wet/Dry Vac.

!

20 Gallon (75 Liter) Wet/Dry Vac With Cart

Model Number: CMXEVBE176560

Electrical Rating: 120 V~ 12 A 60Hz

17

20 Gallon (75 Liter) Wet/Dry Vac With Cart

Model Number: CMXEVBE176560

Always order by Part Number - Not by Key Number

27

26

18

24

3

2

5

6

1

4

7

16

17

8

14

15

910

11

12

13

23

22

21

25

20

19

18

20 Gallon (75 Liter) Wet/Dry Vac

Model Number: CMXEVBE176560

Always order by Part Number - Not by Key Number

Key No. Part No. Description

1 831805 Handle Assembly

2 510710 Dust Drum Assembly

3 73185 Drain Cap

4 830682 8” (20 cm) Wheel Assembly

5 831024-1 Shaft

6 831732 Foot Wheel, Right

7 831731 Foot Wheel, Left

8 828460 Foot, Caster with Storage

9 73102 Caster

10 831807-1 Accessory Storage Bag

11 820563-12 Screw Type “AB” #10 x 1-3/4” (25 mm)

12 509748-4 Bag of Loose Parts (Includes Casters, Button Caps, Nut Caps & Screws)

13 831733 Handle, Left

14 831734 Handle, Right

15 820563-008 Screw, Pan Head Type “AB” #10 x 2-3/4” (69 mm)

1

7

13

6

54

14

8

9

8

11

4

5

10

12

15

3

2

WARNING: To reduce the risk of injury, unplug power cord before servicing the Wet/Dry Vac.

WARNING: All disassembly and repairs should be performed by qualified personnel.

!

19

CRAFTSMAN® LIMITED WARRANTY – 3 YEARS

This limited warranty is provided by Emerson Tool Company, a division of Emerson Electric Co., (“We” or “Our” or “Us”) to

the original consumer owner (“Customer” or “You” or “Your”) of the CRAFTSMAN product with which this limited warranty

is provided (the “CRAFTSMAN Product”).

What is Covered

We warrant to You that your CRAFTSMAN Product will be free from defects in materials and workmanship when used

under normal conditions in accordance with the terms of the Instruction Manual provided to You with the CRAFTSMAN

Product, subject to the exclusions described below, for a period of three years commencing on the date of purchase by

You (the “Warranty Period”). This limited warranty terminates if the original purchaser transfers the CRAFTSMAN Product

to any other person or entity.

What is not Covered

This limited warranty does not extend to and expressly excludes:

• Normal wear and tear and/or replacement attachments or accessories, including, without limitation, power cords,

hoses, filters, and other attachments or accessories that may be offered for sale by Us for use with the CRAFTSMAN

Product.

• Damage or burnout of the CRAFTSMAN Product motor resulting from failure to clear a blockage occurring during the

normal course of use.

• Loss or damage to the CRAFTSMAN Product resulting from conditions beyond Our control including without

limitation, misuse, accident, abuse, neglect, negligence (other than Our’s), overuse beyond intended capacity as set

forth in the Instruction Manual, or modifications or alterations made by anyone other than Us.

• Loss or damage to the CRAFTSMAN Product resulting from failure to use the CRAFTSMAN Product in accordance with

the written instructions, guidelines, and terms and conditions set forth in the Instruction Manual.

• TO THE EXTENT PERMITTED BY LAW, IN NO EVENT SHALL WE BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR

CONSEQUENTIAL DAMAGES, INCLUDING ANY ECONOMIC LOSS, WHETHER RESULTING FROM NONPERFORMANCE,

USE, MISUSE OR INABILITY TO USE THE CRAFTSMAN PRODUCT OR FOR THE NEGLIGENCE OF ETC.

How to Obtain Service

US and Canada – To obtain warranty benefits contact us toll free at 1-888-331-4569 (Mexico 001-881-331-4569).

We will direct you to the nearest service center to review your vacuum for inspection, repairs or replacement.

Mexico - To obtain warranty benefits contact us toll free at 001-881-331-4569. We will direct you to the nearest service

center to review your vacuum for inspection, repairs or replacement.

No Other Express Warranty Applies

This limited warranty is the sole and exclusive warranty provided to You. No other express warranty, written or verbal,

applies including, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

No employee, agent, dealer, or other person is authorized to alter this limited warranty or make any other warranty on

behalf of Us.

What We will do to Correct Problems

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE LIMITED TO REPAIR, REPLACEMENT,

REFUND OF THE CRAFTSMAN PRODUCT.

After You have contacted CRAFTSMAN Product Customer Service Department, We will initiate warranty proceedings,

including a physical inspection, subject to the exclusions and the Warranty Period stated herein, to determine whether to

repair or replace the CRAFTSMAN Product or provide You with a refund.

The decision to repair or replace your CRAFTSMAN Product or to provide a refund is at Our sole discretion. Repair or

replacements provided to You by ETC are at no cost to You if covered under this limited warranty.

If we are unable to provide You with a suitable repaired or replacement CRAFTSMAN Product, we will provide you with

a refund equal to the purchase price of your CRAFTSMAN Product or a credit to be used toward the purchase of a new

CRAFTSMAN Product.

In the event of any dispute between CUSTOMER AND US, either party may choose to resolve the dispute by binding

arbitration. THIS MEANS IF EITHER CUSTOMER OR US CHOOSE BINDING ARBITRATION, NEITHER PARTY SHALL HAVE THE

RIGHT TO LITIGATE SUCH CLAIM IN COURT OR HAVE A JURY TRIAL. DISCOVERY AND APPEAL RIGHTS ARE LIMITED.

This limited warranty gives you specific legal rights, and you may also have other rights, which vary from State to State.

Some states do not allow the exclusion of incidental or consequential damages, so the above limitation may not apply.

Part No. SP7091 Form No. SP7091-1 Printed in Mexico 08/2019

CRAFTSMAN®

is a registered trademark of Stanley Black & Decker, Inc., used under license.

es una marca registrada de Stanley Black & Decker, Inc., utilizada bajo licencio.

est une marque déposée de Stanley Black & Decker, Inc., utilisée sous licence.

2019 CRAFTSMAN

Product Manufactured by: EMERSON TOOL COMPANY

Producto fabricado por: 8100 W. Florissant • St. Louis, MO 63136

Produit fabriqué par : U.S. & Canada Only • É.-U. et Canada seulement

c

La page charge ...

Craftsman MXEVBE176560 Heavy Duty Wet Dry Vacuum Manuel utilisateur

Craftsman MXEVBE176560 Heavy Duty Wet Dry Vacuum Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents