Norcold N61/ N81 Guide d'installation

Taper
Guide d'installation
NORCOLD, Inc.
P.O. Box 4248
Sidney, OH 45365-4248
Part No. 636158G (4/1/2020)
Installation and Owners Manual
N611v and N811v Models
Norcold Customer Service Dept.
Telephone: 800-543-1219
Fax: 734-769-2332
Web Site: www.norcold.com
To the Installer:
Please ax this envelope containing the
Owners Manual adjacent to the refrigerator.
To the Consumer:
Please retain these instructions for future
reference.
FIRE OR EXPLOSION HAZARD
If you smell gas:
1. Open Windows
2. Do not attempt to light appliance.
3. Do not touch electrical switches.
4. Extinguish any open ame
5. Shut o fuel supply.
6. Evacuate immediately and call emergency services.
Failure to follow these instructions could result in re or explosion, which could cause
property damage, personal injury, or death.
Improper installation, adjustment, alteration, service or maintenance
can cause injury or property damage. Refer to this manual. For
assistance or additional information, contact a qualied installer,
service agency, or the gas supplier.
FOR YOUR SAFETY
Do not store or use gasoline or other ammable vapors and liquid in the
vicinity of this or any other appliance.
WARNING
!
WARNING
!
Installation and Owner’s Manual 2
Safety Instructions
- Do not remove the round ground prong from any of the AC power cords.
- At regular intervals, make sure that the refrigerator ue the burner, the vent areas, and the ventilation air pathway
between the vents are completely free from any ammable material or blockage. After a period of storage, it is
especially important to check these areas for any ammable material or blockage caused by animals.
About Your Refrigerator
Storage Volume:
This refrigerator is made for storage of foods and frozen food and for making ice.
Total capacity N611v models N811v models
6.3 cubic feet 7.5 cubic feet
Operating the Refrigerator Controls
Owners Manual
Start the controls for automatic operation:
Push and release the ON/OFF button [30] to start the
refrigerator (See Art02410).
- If the indicator light [185] glows solid green, it means
that:
- 120 volt AC power is available to the refrigerator.
- The refrigerator is operating on AC electric
power.
- If the indicator light [185] glows solid amber, it means
that:
- 120 volt AC power is not available to the refrigerator.
- The refrigerator is operating on propane gas.
- If the indicator light [185] glows solid red, it means that:
- There is a problem and the refrigerator is not cooling.
- Refer to the “Fault Code” section of this manual.
To shut down the refrigerator, push and release the ON/OFF button.
30 185
Art02410
WARNING
!
Installation and Owner’s Manual 3
Refrigerator Temperature Control
The temperatures of the freezer and refrigerator compartments are automatically kept at a xed setting that is within the established
guidelines for safe food storage. If you wish to change the xed setting, you must move the thermistor. To move the thermistor:
- Pull the thermistor and clip o of the n.
- Push the thermistor and clip onto a dierent n.
- Move the thermistor to the left for a colder temperature setting or move to the right for a warmer temperature setting.
- Move the thermistor and clip only three (3) or four (4) ns at a time.
- Allow the temperature of the refrigerator compartments become stable.
You may wish to place a thermometer inside the refrigerator compartment to help with this process.
- If more adjustments are necessary, repeat the steps above.
NOTICE
Refrigerator Care Checklist
Your refrigerator will give you years of trouble free service if you do these simple checks every three to six months:
- Make sure the air ow in the lower intake vent, through the refrigerator coils and condenser, and out the upper exhaust vent is not
blocked or decreased.
- Make sure the area behind the refrigerator is clear. Do not use the area behind the refrigerator for storage of anything, especially
gasoline and other ammable vapors and liquids.
Eects of High Altitude on Propane Gas Operation
When you operate the refrigerator on propane gas at altitudes higher than 5500 feet above sea level:
- You may experience reduced cooling performance of the refrigerator.
- You may experience burner outages.
To avoid these possible problems, Norcold recommends that you operate the refrigerator on AC when at altitudes higher than 5500 feet
above sea level.
Eects of Freezing Temperatures on Refrigerator Operation
A gas absorption refrigerator is not designed to operate in freezing temperatures. If the refrigerator is not equipped for low temperature
operation, and if the cooling system of the refrigerator is exposed to temperatures of 32° F. or lower for an extended period of time,
the refrigerator operation may be disrupted. The refrigerator operation will resume when the cooling system of the refrigerator warms
suciently.
If the refrigerator is equipped for low temperature operation, the refrigerator will operate in temperatures down to 0° F.
Disrupted operation of the refrigerator, due to extended exposure to temperatures of 32° F. or lower, and any costs incurred to warm the
cooling system of the refrigerator are not covered by the Norcold limited warranty. Please contact your local RV dealer for information
about how to resume refrigerator operation or about how to equip your refrigerator for operation in freezing temperatures.
Do not change the installation or the venting of your refrigerator. Refrigerator failures, which are the result of changes to either the
refrigerator installation or to the venting, are not covered by the Norcold limited warranty.
Installation and Owner’s Manual 4
Defrosting
The cooling ns of the refrigerator operate at below freezing temperature and will naturally form frost from humidity, which is always
present in the air. The humidity inside the refrigerator increases:
- with higher outside temperature and humidity.
- with the storage of non-sealed fresh foods or warm foods.
- with the amount of time that the door(s) are open.
- with any air leakage into the refrigerator.
Although the refrigerator is not frost -free, it is made to limit frost on the cooling ns. At regular intervals, the temperature control system
automatically melts most of the frost from the cooling ns. The water from the cooling ns drains into a collection cup that is attached to
the back of the refrigerator. The heat of the cooling system evaporates the water from the collection cup.
It is normal for frost to collect inside the freezer. Excess frost decreases the cooling performance of the refrigerator. Defrost the
refrigerator and freezer as necessary:
- Remove all food from the refrigerator.
- Turn the refrigerator OFF.
Defrosting the refrigerator makes excess water inside the refrigerator.
- Remove the drain hose from the drip cup at the rear of the refrigerator.
- Put the drain hose into a half-gallon or larger container to capture water.
- Put dry towels (etc.) inside the refrigerator and freezer to absorb melted frost.
High temperatures can cause the inside surfaces of the refrigerator to warp or melt. Do not use pans of
HOT water, a hair dryer, or any other high temperature devices to defrost the refrigerator. Do not use any
hard or sharp objects to remove frost. Damage to the interior of the refrigerator can occur.
- To increase the speed of defrosting, put pans of WARM water in the refrigerator and freezer.
- Remove the wet towels (etc.) and dry the interior.
- Remove the drain hose from the large container and put the drain hose back into the drip cup.
- Remove the large container from the enclosure.
- Start up the refrigerator.
- Allow the refrigerator to cool down.
- Return all food to the refrigerator.
NOTICE
CAUTION
!
Installation and Owner’s Manual 5
Refrigerator Maintenance Checklist
Have a qualied RV dealer or a Norcold authorized service center do these annual safety and maintenance checks:
- Examine the gas supply lines for leaks.
- Make sure the propane gas pressure is 11 inches of water column.
- Make sure the combustion seal is complete and intact.
- Make sure the burner and the burner orice are clean.
- Make sure the electrode spark gap is 1/8 - 3/16 inch.
- Make sure the AC voltage is 108 - 132 volts and the DC voltage is 10.5 - 15.4 volts.
- Make sure the thermocouple tip is clean and secure.
- Make sure the area at the rear of the refrigerator is free of any combustible materials, gasoline, and other ammable vapors and
liquids.
Refrigerator Storage
If the refrigerator is stored for an extended period of time, before start uP, make sure there are no obstructions in the vents, the
ventilation air pathway, the burner, the orice, or the ue area.
Refrigerator Maintenance
Gas ame appearance:
While in GAS operation, examine the appearance of the gas ame:
- Turn the temperature switch to the COLDEST position.
- Open the lower intake vent.
The burner box cover can be hot. Wear gloves to avoid burns.
- Remove the burner box cover by removing the screw.
- Look at the gas ame [75] (See Art01605).
- The ame should be:
- a darker blue color on the inside of the ame and a lighter blue color on
the outside of the ame.
- a constant shape without ickering.
- Contact your dealer or Norcold authorized service center if the ame is:
- yellow
- ickering or changing shape.
75
76
Art01605
CAUTION
!
Installation and Owner’s Manual 6
- Make sure the ame does not touch the inside of the ue tube [76].
- If the ame touches the inside of the ue tube, contact your dealer or Norcold authorized service center.
- Close the burner box door.
Remove and clean the burner orice:
Your dealer or Norcold authorized service center must do this procedure.
Remove and clean the burner orice (See Art00956):
- Close the valve at the propane gas tank(s).
- Push and release th ON/OFF button to shut down the refrigerator.
The burner box cover can be hot. Wear gloves to avoid burns.
- Open the lower intake vent.
- Remove the drip cup by removing the screw.
- Remove the burner box cover by removing the screw.
To avoid possible propane gas leaks, always use two wrenches to loosen and tighten the gas supply line
connections.
- Remove the are nut from the orice assembly [77] (See Art00956).
- Remove the burner [78] from the orice assembly.
Do not try to remove the orice [79] from the orice adapter [80] when cleaning. Removal will damage
the orice and seal of the orice and can cause a propane gas leak. Leaking propane gas can ignite or
explode which can result in dangerous personal injury or death. Do not clean the orice with a pin or
other objects.
- Clean the orice assembly with air pressure and alcohol only.
- Using a wrench, assemble the orice assembly to the burner.
- Assemble the are nut to the orice assembly.
- Examine all of the connections for gas leaks.
- Clean the burner box.
- Assemble the burner box cover.
- Assemble the drip cup.
Art 00956
77
78
79
80
CAUTION
!
WARNING
!
Remove the Refrigerator
CAUTION
!
WARNING
!
Your dealer or Norcold authorized service center must do this procedure.
The rear of the refrigerator has sharp edges and corners. To prevent cuts or abrasions when working on the
refrigerator, be careful and wear cut resistant gloves.
1. Close the valve at the propane gas tank(s).
Installation and Owner’s Manual 7
To avoid possible propane gas leaks, always use two wrenches to loosen and tighten the gas supply line
connections.
2. Remove the AC power cord(s) from the receptacle.
3. Remove the DC wiring from the refrigerator:
- Put a mark on the DC wires so you can put them back in the correct location.
- Remove the DC fuse or remove the DC wiring from the battery or the converter.
- Remove the DC wires from the refrigerator.
4. Open the lower intake vent and remove the gas supply line from the bulkhead tting of the refrigerator.
5. Remove the plastic plugs from the mounting anges of the refrigerator.
6. Remove the screws from the mounting ange at the rear of the refrigerator.
7. Remove the screws from the upper and lower mounting anges on the front of the refrigerator.
8. Remove the refrigerator from the opening.
WARNING
!
Reinstall the Refrigerator
Your dealer or Norcold authorized service center must do this procedure.
Make sure the combustion seal is not broken, is completely around the refrigerator mounting anges, and
is between the mounting anges and the wall of the enclosure. If the combustion seal is not complete,
exhaust fumes can be present in the living area of the vehicle. The breathing of exhaust fumes can cause
dizziness, nausea, and in extreme cases, death.
1. Push the refrigerator completely into the enclosure.
2. Install the screws in the upper and then the lower mounting anges on the front of the refrigerator.
3. Install the screws in the mounting ange at the rear of the refrigerator.
4. Put the plastic plugs into the mounting anges of the refrigerator.
To avoid possible propane gas leaks, always use two wrenches to loosen and tighten the gas supply line
connections.
5. Attach the gas supply line to the bulkhead tting of the refrigerator.
6. Open the valve at the propane gas tank(s).
Do not allow the leak checking solution to touch the electrical components. Many liquids are electrically
conductive and can cause electrical shorts and in some cases, re.
7. Examine the gas supply line for leaks.
8. Connect the DC wiring to the refrigerator:
- Connect the DC wires to the refrigerator.
- Install the DC fuse or connect the DC wiring to the battery or the converter.
9. Connect the black AC power cord to the receptacle.
WARNING
!
WARNING
!
WARNING
!
Installation and Owner’s Manual 8
Wiring Diagram
BR/BR
RD/RG
RD/RG
BR/BR
WH/BC
RD/RG
BK/NR
BK/NR
BK/NR
BK/NR
4
1
2
3
WH/BC
WH/BC
WH/BC
WH/BC
4
1
2
3
+
+
-
-
AC HEATER / ÉLÉMENT CHAUFFANT CA
LIGHT / LAMPE
THERMISTOR / THERMISTANCE
GAS VALVE / ROBINET DE GAZ
IGNITER / ALLUMEUR
DIVIDER HEATER / ELEMENT DE CLOISON
TEMPERATURE SWITCH / INTERRUPTRUR DE TEMPÉRATURE
TEMPERATURE SWITCH / INTERRUPTRUR DE TEMPÉRATURE
FAN / VENTILATEUR
IM WATER LINE HEATER / CHAUFFERETTE DU YUYAU D’EAU DE LA MACHINE À GLAÇONS
CHASSIS GROUND / MASSE DU CHASSIS
DOOR SWITCH / CONTACTEUR DE PORTE
SWITCHED 12VDC / COMMUTÉ 12VCD
FUSED CONTINUOUS 12VDC/ CONTINU FONDU 12VCD
COMMUNICATIONS / COMMUNICATIONS
DISPLAY GROUND / AFFICHAGE LA TERRE
AUXILIARY GROUND / MASSE AUXILIAIRE
AUXILIARY +12VDC / AUXILIAIRE +12VCD
DIVIDER +12VDC / DE CLOISON +12VCD
GAS VALVE +12VDC / ROBINET DE GAZ +12VCD
5
K
J
G
E
D
H
I
7
8
B
6
C
2
F
1
A
*
OPTIONAL / EN OPTION
*
*
*
*
*
*
*
*
*
*
**
*
*
*
*
B
A
6
5
4
3
2
1
L
K
J
I
H
G
F
E
D
C
7
8
*
*
*
*
M
TEMPERATURE SWITCH / INTERRUPTRUR DE TEMPÉRATURE
M
12VDC
GND
LIMIT_OUT
LIMIT_IN
AC_HT_HI_2
AC_HT_HI
AC_HT_LO
AC_HT_LO_2
L1
L2
4
1
2
35
6
125
3
4
67
8
9
10
1
2
K2
K5
K3
K1
K4
F2 8-Amp
F1 5-Amp
-
+
P3
-
-
-
+
+
+
+
+
P1
ON-OFF
Vreg
1
2
3
4
5
MICRO
P2
P1
+
U1
K2
K5
K4
K3
K1
YL-GN/JN-VE
WH/BC
BK/NR
BK-WH/NR-BC
RD/RG
GN/VE
RD/RG
BK/NR
WH-RD/BC-RG
BU/BL
WH-VT/BC-VT
GN/VE
WH/BC
RD/RG
RD/RG
BK/NR
BK/NR
120VCA
120VAC
+
-
BATTERY /
ACCUMULATEUR
POWER BOARD/PANNEAUD’ALMENTATION
GOOD DISPLAY BOARD/ MIEUX CARTE D’AFFICHAGE
3
4
*
*
F1 5-Amp DC FUSE / FUSIBLE DE 5 AMPERES CD
F2 8-Amp AC FUSE / FUSIBLE DE 5 AMPERES CA
L
RD-WH/RG-BC
WH-BK/BC-NR
T1
K
K
Art02408
Installation and Owner’s Manual 9
Wiring Pictorial
+12VDC/VCD
-12VDC/VCD
K
AC HEATER / ÉLÉMENT CHAUFFANT CA
LIGHT / LAMPE
THERMISTOR / THERMISTANCE
GAS VALVE / ROBINET DE GAZ
IGNITER / ALLUMEUR
DIVIDER HEATER / ELEMENT DE CLOISON
TEMPERATURE SWITCH / INTERRUPTRUR DE TEMPÉRATURE
TEMPERATURE SWITCH / INTERRUPTRUR DE TEMPÉRATURE
FAN / VENTILATEUR
IM WATER LINE HEATER / CHAUFFERETTE DU YUYAU D’EAU
DE LA MACHINE À GLAÇONS
CHASSIS GROUND / MASSE DU CHASSIS
DOOR SWITCH / CONTACTEUR DE PORTE
B
A
M
L
K
J
I
H
G
F
E
D
C
*
*
*
*
TEMPERATURE SWITCH / INTERRUPTRUR DE TEMPÉRATURE
L1
L2
P1
5
POWER BOARD/ PANNEAU D’ALIMENTATION
4
P2
T1
5 AMP
AC_HT_HI_2
LIMIT_IN
LIMIT_OUT
AC_HT_LO
AC_HT_HI
AC_HT_LO_2
GND
12VDC
10
7
6 1
10
1
3
2
5
1
1
1
2
3
6
1
8 AMP
F2
F1
DISPLAY BOARD/CARTE D’AFFICHAGE
B
A
L
F
D
C
I
*
J
*
H
*
G
*
M
E
*
*
*
*
*
*
*
*
*
*
*
OPTIONAL / EN OPTION
K
Art02409
Installation and Owner’s Manual 10
Replacement Parts
You may purchase replacement parts through your local RV dealer or authorized Norcold Service Center.
Wiring Diagram and Pictorial - Low Ambient Heater (optional)
Art02312-1
RH
GND
F3
TS
BK/NR
BR/BR
VDC
VDC
F3
TS
RH
BR/BR
BK/NR
GND
This kit supplies DC voltage to the heater any time the ambient temperature is low enough. Extended storage during
cold weather will drain the vehicle batteries. To prevent battery drain, remove the 3 amp fuse from the low ambient
heater.
NOTICE
Installation and Owner’s Manual 11
Fault Codes
Indicator Light and Color
Green, ashes o once every
20 seconds
Amber, ashes o once every
20 seconds.
Red, on solid.
Red, ashes on two (2) times
every ve (5) seconds.
Red, ashes on three (3) times
every ve (5) seconds.
Red, ashes on four (4) times
every ve (5) seconds.
Red, ashes on ve (5) times
every ve (5) seconds.
Red, ashes on eight (8) times
every ve (5) seconds.
Red, ashes on nine (9) times
every ve (5) seconds.
Meaning
The refrigerator is operating
on AC electric power. The
thermister sensed inoperable,
so temperature is being
controlled by backup operating
system.
The refrigerator is operating on
propane gas. The thermister
sensed inoperable, so
temperature is being controlled
by backup operating system.
No AC input sensed available.
Refrigerator defaulted to
propane gas operation, but
did not establish a ame (gas
lockout).
This is a fault within the
refrigerator controls.
A temperature limit swich is
open.
This is a problem with the AC
heater relay
A ame is present at the burner
when there should none.
The DC voltage to the
rergerator is too low.
The DC voltage to the
rergerator is too low to support
cooling when operating on
propane gas.
Corrective Actions
Check:
- That the thermister is plugged in.
- See your dealer or authorized Norcold Service Center.
Check:
- That the thermister is plugged in.
- See your dealer or authorized Norcold Service Center.
Check:
- That the refrigerator is plugged into a servicable oulet.
- That the valve of the propane gas tank(s) is open.
- That the propane gas is at the correct pressure.
- That the manual shut o valve of the refrigerator is open.
- That there is not air in the propane gas supply line.
- See your dealer or authorized Norcold Service Center.
Turn the refrigerator power OFF and then back ON to reset.
If the Fault Code continues, see your dealer or authorized
Norcold Service Center.
This is not owner serviceable. See your dealer or
authorized Norcold Service Center.
This is not owner serviceable. See your dealer or
authorized Norcold Service Center.
This is not owner serviceable. See your dealer or
authorized Norcold Service Center.
Check:
- That the battery charging equipment of the vehicle is
operational.
- That the AC/DC converter is operational (if applicable).
- See your dealer or authorized Norcold Service Center.
Check:
- That the battery charging equipment of the vehicle is
operational.
- That the AC/DC converter is operational (if applicable).
See your dealer or authorized Norcold Service Center.
The refrigerator is not cooling, If the indicator light is either on solid red or ashes on red.
NOTICE
Installation and Owner’s Manual 12
Safety Instructions
- This refrigerator is not approved for use as a free standing refrigerator. It is equipped for the use of propane gas only
and can not be changed to use any other fuels (natural gas, butane, etc.).
- Incorrect installation, adjustment, alteration, or maintenance of this refrigerator can cause personal injury, property
damage, or both.
- Obey the instructions in this manual to install intake and exhaust vents.
- Do not install the refrigerator directly on carpet. Put the refrigerator on a metal or wood panel that extends the full
width and depth of the refrigerator.
Certication and Code Requirements
The refrigerator installation must conform to the following, as applicable:
In the United States and Canada:
- Local codes, or in the absence of local codes, the National Fuel Gas Code, ANSI Z223.1/NFPA 54, the Natural Gas and Propane
installation Code, CSA B149.1, ANSI A119.2 Recreational Vehicles Code, and CSA Z240 RV Series, Recreational Vehicles.
- A manufactured home (mobile home) installation must conform with the Manufactured Home Construction and Safety Standard,
Title 24 CFR, Part 3280 [formerly the Federal Standard for Mobile Home Construction and Safety, Title 24 (part 280), and the
current CSA Z240.4, Gas-equipped Recreational Vehicles and Mobile Housing.
- If an external power source is utilized, the appliance, when installed, must be electrically grounded in accordance with local codes
or, in the absence of local codes, the National Electrical code, and ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.2.
Parts 1 and 2.
All propane gas supply piping and ttings must obey local, state, and national codes about type and size. These components must also
obey the current NFPA 1192 section 2-4, and in Canada with the current CAN 1-6.10 Standard.
Ventilation Requirements
The completed installation must:
- Make sure there is sucient intake of fresh air for combustion.
- Make sure the living space is completely isolated from the combustion system of the refrigerator.
- Make sure there is complete and unrestricted ventilation of the ue exhaust which, in gas mode, can produce carbon
monoxide. The breathing of carbon monoxide fumes can cause dizziness, nausea, or in extreme cases, death.
The bottom of the opening for the lower intake vent, which is also the service access door, must be even with or immediately below the
oor level. This allows any leaking propane gas to escape to the outside and not to collect at oor level.
CSA International certication allows the refrigerator to have zero (0) inch minimum clearance at the sides, rear, top, and bottom. While
there are no maximum clearances specied for certication, the following maximum clearances are necessary for correct refrigerator
performance:
Bottom 0 inch min. 0 inch max.
Each Side 0 inch min 1/2 inch max.
Top 0 inch min. 1/4 inch max.
Rear 0 inch min. 1 inch max.
These clearances plus the lower and upper vents cause the natural air draft that is necessary for good refrigeration. Cooler air comes
in through the lower vent, goes up around the refrigerator coils where it removes the excess heat from the refrigerator components, and
goes out through the upper vent. If this air ow is blocked or decreased, the refrigerator will not cool correctly.
Installation Manual
WARNING
!
WARNING
!
Installation and Owner’s Manual 13
Key Refrigerator Dimensions
These key refrigerator dimensions are for your reference as necessary (See Art01733).
Refrigerator cabinet width w/o trim:
23.47 in. max. .................................................. 1
Refrigerator width overall w/ trim:
24.6in............................................................... 2
Refrigerator cabinet to side trim:
0.80 in.............................................................. 3
Refrigerator cabinet height w/o trim:
N600 models - 52.85 in. max. ......................... 4
N800 models - 59.85 in. max. ......................... 4
Refrigerator height overall w/ trim:
N600 models - 54.5 in. .................................... 5
N800 models - 61.5 in. .................................... 5
Refrigerator cabinet to top/bottom trim:
0.93 in.............................................................. 6
Enclosure wall to hinges:
1.10 in.............................................................. 7
Refrigerator cabinet to center of handles:
N600 models - 32.5 in. .................................... 8
N800 models - 39.5 in. .................................... 8
Assemble the Enclosure for the Refrigerator
1. Make sure the enclosure is 59.88 - 60.01 inches high for N81X models or 52.88 - 53.01 inches high for N61X models x 23.50 -
23.63 inches wide x 24 inches deep.
2. Make sure the oor is solid and level.
- The oor must be metal or a wood panel and extend the full width and depth of the enclosure.
- The oor must be able to support the weight of the refrigerator and its contents.
3. Make sure there are no adjacent heat sources such as a furnace vent, a hot water heater vent, etc.
4. If there is more than 1/2 inch between either side of the refrigerator and the inside of the enclosure:
- Fill the space with berglass insulation or add a bae to eliminate the excess clearance.
- Make sure that the rear of the batt-type insulation is between 18 - 19 inches from the face of the enclosure.
- Securely attach the batt-type insulation to the enclosure so that it remains in this position during refrigerator installation, if it
becomes wet, and in windy conditions.
Art01733
1
8
7
5
6
4
3
2
Installation and Owner’s Manual 14
Install the Lower and Upper Vents
1. Using the following chart, decide which vents and rough opening (RO) sizes to use:
Certied Vent P/N RO Height RO Width
Upper Roof Exhaust Cap 622293 N/A N/A
Upper Roof Exhaust Vent 616319 24 in. 5 1/4 in.
Lower Metal Intake 616010 13 5/8 in. 21 5/8 in.
Upper Exhaust & Lower Intake Plastic-large 621156 13 3/4 in. 21 1/2 in.
Upper Exhaust & Lower Intake Plastic-small 620505, 636264 6 3/16 in. 17 13/16 in.
2. Install the lower intake vent (See Art01598, Art01599, and Art01602):
The lower intake vent is also the service access opening for the components
on the rear of the refrigerator.
Make sure the bottom of the opening of the lower intake vent is
even with or immediately below the oor level. This allows any
leaking propane gas to escape to the outside and not to collect at
oor level.
- Make sure the bottom of the opening of the lower intake vent [9] is even with or
immediately below the oor level.
- When using either 616010 or 621156 vent, align the lower intake vent vertically below the
coils [10] and the condenser [11] of the refrigerator.
- When using either 620505 or 636264 vent, make sure that the centerline [297] of the
vent rough opening [295] is 1 1/2 inch ± 1/8 inch [298] to the right of the refrigerator
centerline [296] (See Art02424 ).
10
11
9
Art01602
WARNING
!
NOTICE
296
Art02424
298
295
297
Installation and Owner’s Manual 15
3. Install the upper exhaust vent:
Make sure that no sawdust, insulation, or other construction debris is on the refrigerator or in the enclosure.
Debris can cause a combustion hazard and prevent the refrigerator from operating correctly.
Tighten the screws of the upper roof exhaust cap to 10 inch-pounds max. Also make sure that the air ow around the
upper roof exhaust cap is not blocked or decreased by other roof mounted features such as a luggage carrier, an air
conditioner, a solar panel, etc.
- If the design of the vehicle allows, install the roof exhaust vent [12] directly above the condenser [11] of the refrigerator (See
Art01598).
- Install a bae [13] to prevent stagnant hot air in the area [14] above the refrigerator.
- Make sure there is less than 1/4 inch clearance [15] between the bae and the top of the refrigerator.
- Make sure the bae is the full width of the inside of the enclosure.
- If the design of the vehicle does not allow you to install the roof exhaust vent directly above the condenser of the refrigerator (See
Art01599).
- Align the roof exhaust vent [12] above the condenser [11] of the refrigerator and move it inboard as necessary.
Art01598
14
9
11
12
13
15
16
10
17
18
15
19
16
Art01599
20
14
13
12
11
16
9
10
18
17
19
16
19
CAUTION
!
NOTICE
Installation and Owner’s Manual 16
- Install two baes [13] to prevent stagnant hot air in the area [14] above the refrigerator.
- Make sure the baes are the full width of the inside of the enclosure.
- Make sure that the baes are no more than 45° from vertical [20].
- Put one bae between the top rear edge of the refrigerator and the inside edge of the upper exhaust vent opening.
- Put the other bae between the outside edge of the upper exhaust vent opening and the side wall of the vehicle.
- If the depth of the enclosure is 24 inches or more and is less than 25 inches, no baes are necessary at the rear of the enclosure.
- If the depth of the enclosure is 25 inches or more and is less than 26 inches, add two baes [16] to the rear of the enclosure (See
Art01598 and Art01599).
- Put one bae 18 inches to 18 1/2 inches above the bottom of the enclosure [17].
- Put the other bae at the lowest edge of the condenser [11] of the refrigerator.
- Make sure that the baes are 1 inch or less [19] from the coils [10] and condenser of the refrigerator.
- Make sure that the baes are the full width of the inside of the enclosure.
- If the depth of the enclosure is more than 26 inches, install a wood or an aluminum or galvanized sheet solid box bae [21] in the
rear of the enclosure (See Art01617-1 and Art01618-1).
- Make sure that the bottom of the solid box bae is 18 inches to 18 1/2 inches above the bottom of the enclosure [17].
Art01617-1
14
15
13
12
19
11
21
17
10
9
Art01618-1
14
20
12
13
11
19
21
17
10
9
Installation and Owner’s Manual 17
- Make sure that the back of the solid box bae is perpendicular to the bottom of the
enclosure.
- Make sure that the back of the solid box bae is either against the top of the enclosure or
against the angled bae [13] (depending on the vehicle design).
- Make sure that the solid box bae is one inch or less [19] from the coils [10] and
condenser of the refrigerator.
- Make sure that the solid box bae is the full width of the inside of the enclosure.
- If the design of the vehicle does not allow you to install a roof exhaust vent, install an upper
side-wall exhaust vent.
The refrigerator is 23.7 in. min. to 24.0 in. max. from the rear of the breaker to
the rear of the condenser [22]. N611v models are 47.1 in. min. to 47.4 in. max.
from the bottom of the refrigerator to the bottom of the refrigerator condenser
[23]. N811v models are 54.1 in. min. to 54.4 in. max. from the bottom of the
refrigerator to the bottom of the refrigerator condenser [23] (See Art01601).
Only use an upper side-wall exhaust vent on refrigerator models
that are equipped with a fan. If you use an upper side-wall exhaust
vent on a refrigerator model that is not equipped with a fan, the
refrigerator cooling performance will be poor.
- Make sure the refrigerator model is equipped with a fan.
- Install the upper side-wall exhaust vent [24] (See Art01592 and Art01593).
- For N611v models, make sure the distance [25] from the bottom of the enclosure to
the top of the rough opening for the upper exhaust vent is at least 55 inches.
- For N811v models, make sure the distance [25] from the bottom of the enclosure to the top of the rough opening for the
upper exhaust vent is at least 62 inches.
- Align the upper exhaust vent [24] horizontally above the lower
intake vent [9] of the refrigerator.
- To prevent stagnant hot air in the area above the refrigerator,
install a wood or an aluminum or a galvanized steel sheet
bae [13] between the top of the refrigerator and the top of
the upper exhaust vent.
- Make sure there is less than 1/4 inch clearance between
the bae and the top of the refrigerator and that the
bae overlaps the refrigerator 1 inch or less.
- Make sure that the bae is against the wall of the
vehicle at the top of the upper exhaust vent and 1/4 inch
or less from the top of the opening for the upper exhaust
vent [15].
- Make sure the bae is the full width of the inside of the
enclosure.
- When using an upper side-wall exhaust vent 621156:
- If the depth of the enclosure is 24 inches or more and is less than
26 inches [27], install a bent aluminum or galvanized steel sheet
bae [26] to the rear of the enclosure (See Art01592-1).
22
23
Art01601
Art01592-1
15
13
15
11
213
15
25
24
26
9
10
27
CAUTION
!
NOTICE
Installation and Owner’s Manual 18
- Make sure that the bend of the bae is the full
width of the inside of the enclosure.
- Make sure that the bend of the bae is ush with
the bottom edge of the upper intake vent door
frame.
- Make sure that the top edge of the bae is 1/4
inch [213] below the bottom of the condenser
and that there is 1/4 inch or less clearance [15]
between the rear of the condenser and the bae.
- If the depth of the enclosure is more than 26 inches
[27], install a wood or an aluminum or a galvanized
steel sheet solid box bae [21] between the lower
intake vent and the upper exhaust vent (See
Art01593-1).
- Make sure that the solid box bae is the full width
of the inside of the enclosure.
- Make sure that the bottom of the solid box bae
is 18 inches to 18 1/2 inches above the bottom of
the enclosure [17].
- Make sure that the back of the solid box bae is
perpendicular to the bottom of the enclosure.
- Make sure that the horizontal top of the solid box
bae is even with the bottom edge of the upper
exhaust vent [24].
- Make sure that the horizontal top edge of the
bae is 1/2 inch [213] or less below and 1/4
inch or less behind the lower rear corner of the
condenser [11].
- Make sure that there is 1/4 inch or less clearance [15]
between the rear of the condenser and the bae.
- When using an upper side-wall exhaust vent 620505 or 636264:
- If the depth of the enclosure is 24 inches or more and is
less than 25 inches [27], do not install a bae.
- If the depth of the enclosure is 25 inches or more and is
less than 26 inches [27], install a bae [16] to the rear of
the enclosure (See Art02425).
- Make sure that the bae is the full width of the inside
of the enclosure.
Art01593-1
27
17
10
9
25
21
24
1513
15
11
15
213
Art02425
15
13
15
25
24
26
9
10
27
11
15
213
Installation and Owner’s Manual 19
- Make sure that the top edge of the bae is
between 1/4 inch and 1/2 inch [213] below
the condenser and that there is 1/4 inch or
less clearance [15] between the rear of the
condenser and the bae.
- For the best cooling performance, the
bae should be 1/4 inch below the bottom
of the condenser.
- If the depth of the enclosure is more than 26 inches
[27], install a wood or an aluminum or galvanized
steel sheet solid box bae [21] between the lower
intake vent and the upper exhaust vent (See
Art02526).
- Make sure that the solid box bae is the full
width of the inside of the enclosure.
- Make sure that the bottom of the solid box
bae is 18 inches to 18 1/2 inches above the
bottom of the enclosure [17].
- Make sure that the back of the solid box bae
is perpendicular to the bottom of the enclosure.
- Make sure that the horizontal top of the solid
box bae is even with the bottom edge of the
condenser [11].
- Make sure that the vertical top edge of the
bae is between 1/4 inch and 1/2 inch [213]
below the condenser.
- Make sure that there is 1/4 inch or less
clearance [15] between the rear of the
condenser and the bae.
For rear wall installation please refer to special isntructions 620918 for additional required instructions.
Art02426
27
17
10
9
25
21
24
1513
15
11
15
213
The doors are made to accept decorative panels. The decorative panels must be 3/16 inch or less in thickness. Install
the decorative door panels in the refrigerator doors before installing the refrigerator in the vehicle.
- Make an upper door panel that is 21 19/32 inches wide x 14 17/32 inches high.
- Make a lower door panel that is:
- 21 19/32 inches wide and
- 31 5/8 inches high (for N611v models) or
- 38 5/8 inches high (for N811v models).
- Pull the panel retainer [37] o each door (See Art00965).
- Push the decorative door panel [38] into the slots of the door [39].
- Push each panel retainer into the slot on the edge of the door.
Install Decorative Door Panels
Art00965
37
38
39
NOTICE
Rear wall Installation
Installation and Owner’s Manual 20
Put the refrigerator in position (See Art00963, Art00963, and Art00964):
Make sure the combustion seal [28] is not broken, is completely around
the refrigerator mounting anges, and is between the mounting anges
and the wall of the enclosure If the seal is not complete, exhaust fumes
can be present in the living area of the vehicle. The breathing of exhaust
fumes can cause dizziness, nausea, or in extreme cases, death.
- Push the refrigerator completely into the enclosure.
- Put the upper trim piece [40] onto the front of the refrigerator.
- put screws [41] through the upper and lower mounting anges on the front of the refrigerator
and into the enclosure wall and oor.
- Put a cap [42] on each of the screw holes in the upper trim piece [4] on the front of the refrigera-
tor.
Do not omit the bottom trim piece. This piece is part of the combustion
seal.
- Push the bottom trim piece [29] onto the front of the refrigerator.
- Put two screws [41] through the trim piece, the mounting ange, and into the oor.
- Put screws through the mountingange on the rear of the refrigerator and into the oor.
Install the Refrigerator
Art00962
28
29
Art00963
41
42
40
Art00964
41
29
41
Connect the Electrical Components
Connect the 120 volts AC supply:
Connect the AC power cord(s) only to a grounded three-prong
receptacle. Do not remove the round ground prong from any
of the AC power cords. Do not use a two prong adapter or an
extension cord with any of the AC power cords. Operation of
the refrigerator without correct ground can cause dangerous
electrical shock or death if you are touching the metal parts of
the refrigerator.
- Make sure the receptacle is positioned within easy reach of the lower intake vent.
- Make sure the power cord(s) does not touch the burner cover, the ue pipe, or any
hot component that could damage the insulation of the power cord.
Connect the 12 volts DC supply:
1. Determine the min. wire size and the max. fuse size to use:
If you use an incorrect wire size and/or fuse size, electrical re
can result.
- Use a minimum of 18 AWG wire and a maximum 6 Amp fuse.
- If the wire size is larger than the min. size, use the correct fuse per RVIA A119.2 standard or local codes.
WARNING
!
WARNING
!
WARNING
!
WARNING
!
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Norcold N61/ N81 Guide d'installation

Taper
Guide d'installation

dans d''autres langues