Pioneer AVH-P7500DVD Le manuel du propriétaire

English

Español

Deutsch

Français

Italiano

Nederlands

AVH-P7500DVD

This product conforms to new cord colors.

Los colores de los cables de este producto se confor-

man con un nuevo código de colores.

Dieses Produkt entspricht den neuen kabelfarben.

Le code de couleur des câbles utilisé pour ce produit est

nouveau.

Questo prodotto è conforme ai nuovi codici colori.

De kleuren van de snoeren van dit toestel zijn gewijzigd.

INSTALLATION MANUAL

MANUEL D’INSTALLATION

1
Contents
Connecting the Units  ................................ 1
Connecting the system  ...................................... 3
Connecting the power cord (1) .......................... 4
Connecting the power cord (2) .......................... 5
When connecting to separately sold power 
amp ............................................................ 7
When connecting with a back-up camera  ........ 9
When connecting the external video 
component and the display  ...................... 10
Attaching the noise filters  .............................. 11
Installation ................................................ 12
Installing the hide-away unit  .......................... 13
DIN Front/Rear-mount .................................... 13
DIN Front-mount  ............................................ 14
DIN Rear-mount .............................................. 15
Fixing the front panel  ...................................... 16
Installing the remote control unit  .................... 16
CAUTION:
• PIONEER does not recommend that
you install or service your display your-
self. Installing or servicing the product
may expose you to risk of electric shock
or other hazards. Refer all installation
and servicing of your display to autho-
rized Pioneer service personnel.
• Secure all wiring with cable clamps or
electrical tape. Do not allow any bare
wiring to remain exposed.
• Do not drill a hole into the engine com-
partment to connect the yellow lead of
the unit to the vehicle battery. Engine
vibration may eventually cause the insu-
lation to fail at the point where the wire
passes from the passenger compartment
into the engine compartment. Take
extra care in securing the wire at this
point.
• It is extremely dangerous to allow the
display lead to become wound around
the steering column or gearshift. Be sure
to install the display in such a way that
it will not obstruct driving.
• Make sure that wires will not interfere
with moving parts of the vehicle, such as
the gearshift, parking brake or seat slid-
ing mechanism.
• Do not shorten any leads. If you do, the
protection circuit may fail to work
properly.
Connecting the Units

English

Español

Deutsch

Français

Italiano

Nederlands

2

Note:

• This unit is for vehicles with a 12-volt battery and

negative grounding. Before installing it in a recre-

ational vehicle, truck, or bus, check the battery

voltage.

• To avoid shorts in the electrical system, be sure to

disconnect the ≠ battery cable before beginning

installation.

• Refer to the owner’s manual for details on

connecting the power amp and other units, then

make connections correctly.

• Secure the wiring with cable clamps or adhesive

tape. To protect the wiring, wrap adhesive tape

around them where they lie against metal parts.

• Route and secure all wiring so it cannot touch any

moving parts, such as the gear shift, handbrake

and seat rails. Do not route wiring in places that

get hot, such as near the heater outlet. If the insu-

lation of the wiring melts or gets torn, there is a

danger of the wiring short-circuiting to the vehicle

body.

• Don’t pass the yellow lead through a hole into the

engine compartment to connect to the battery.

This will damage the lead insulation and cause a

very dangerous short.

• Do not shorten any leads. If you do, the protection

circuit may fail to work when it should.

• Never feed power to other equipment by cutting

the insulation of the power supply lead of the unit

and tapping into the lead. The current capacity of

the lead will be exceeded, causing overheating.

• When replacing fuse, be sure to use only fuse of

the rating prescribed on the fuse holder.

• Since a unique BPTL circuit is employed, never

wire so the speaker leads are directly grounded or

the left and right ≠ speaker leads are common.

• If the RCA pin jack on the unit will not be used,

do not remove the caps attached to the end of the

connector.

• Speakers connected to this unit must be high-

power types with minimum rating of 50 W and

impedance of 4 to 8 ohms. Connecting speakers

with output and/or impedance values other than

those noted here may result in the speakers catch-

ing fire, emitting smoke, or becoming damaged.

• When this product’s source is switched ON, a

control signal is output through the blue/white

lead and blue lead. Connect to an external power

amp’s system remote control or the car’s Auto-

antenna relay control terminal (max. 300 mA 12

V DC). If the car features a glass antenna, connect

to the antenna booster power supply terminal.

• When an external power amp is being used with

this system, be sure not to connect the blue/white

lead to the amp’s power terminal. Likewise, do

not connect the blue lead to the power terminal of

the auto-antenna. Such connection could cause

excessive current drain and malfunction.

• To avoid short-circuiting, cover the disconnected

lead with insulating tape. Especially, insulate the

unused speaker leads without fail. There is a pos-

sibility of short-circuiting if the leads are not insu-

lated.

• To prevent incorrect connection, the input side of

the IP-BUS connector is blue, and the output side

is black. Connect the connectors of the same col-

ors correctly.

• This unit cannot be installed in a vehicle that

does not have an ACC (accessory) position on

the ignition switch. (Fig. 1)

Fig. 1

• The black lead is ground. Please ground this lead

separately from the ground of high-current prod-

ucts such as power amps.

If you ground the products together and the

ground becomes detached, there is a risk of dam-

age to the products or fire.

No ACC positionACC position

O

N

S

T

A

R

T

O

F

A

C

O

N

S

T

A

R

T

O

F

• Cords for this product and those for other prod-

ucts may be different colors even if they have

the same function. When connecting this product

to another product, refer to the supplied manuals

of both products and connect cords that have the

same function.

3

Connecting the Units

Connecting the system

Fig. 2

Multi-CD player

(sold separately)

IP-BUS cable

3m

This product

IP-BUS input

(Blue)

Hide-away TV tuner

(e.g. GEX-P6400TVP)

(sold separately)

AV-BUS input (Blue)

AV-BUS cable (supplied

with TV tuner)

IP-BUS cable (supplied

with TV tuner)

10 cm

Black

Blue

Black Blue

Black

Blue

30 pin cable (supplied)

21 pin cable (supplied)

Violet

3m

15 cm

Violet

Black

Hide-away unit

(supplied)

Antenna jack

Antenna cable (supplied)

3m

40 cm

Navigation unit

(e.g. AVIC-900DVD)

(sold separately)

26 pin cable

Yellow

15 cm

Auto-EQ&TA mic jack

See the operation manual.

Connecting the power cord (1)

English

Español

Deutsch

Français

Italiano

Nederlands

Fig. 3

4

Yellow

To terminal always supplied

with power regardless of

ignition switch position.

Black (ground)

To vehicle (metal) body.

Black

Black/white

Center speaker

Hide-away unit

Fuse holder

+

≠

5

Connecting the Units

Connecting the power cord (2)

Connect leads of the same

color to each other.

Cap (1*)

When not using this terminal,

do not remove the cap.

ISO connector

Fuse holder

1*

2*

4*

3*

5*

Yellow (2*)

To terminal always supplied

with power regardless of

ignition switch position.

Red (4*)

To electric terminal controlled

by ignition switch (12 V DC)

ON/OFF.

Yellow (3*)

Back-up

(or accessory)

Red (5*)

Accessory

(or back-up)

Black (ground)

To vehicle (metal) body.

Orange/white

To lighting switch terminal.

Note:

In some vehicles, the ISO connector

may be divided into two. In this case,

be sure to connect to both connectors.

Fuse resistor

Note:

Depending on the kind of vehicle, the

function of 3* and 5* may be different.

In this case, be sure to connect 2* to 5*

and 4* to 3*.

Blue/white (6*)

Speaker leads

White: Front left +

White/black: Front left ≠

Gray: Front right +

Gray/black: Front right ≠

Green: Rear left +

Green/black: Rear left ≠

Violet: Rear right +

Violet/black: Rear right ≠

The pin position of the ISO connector will differ

depending on the type of vehicle. Connect 6* and

7* when Pin 5 is an antenna control type. In

another type of vehicle, never connect 6* and 7*.

This product

6

English

Español

Deutsch

Français

Italiano

Nederlands

Note:

• The position of the parking brake switch depends

on the vehicle model. For details, consult the

vehicle Owner’s Manual or dealer.

Connection method

Clamp the lead.1. 2. Clamp firmly with

needle-nosed

pliers.

Parking brake

switch

Power supply side

Ground side

Light green

Used to detect the ON/OFF status of the parking brake.

This lead must be connected to the power supply side of the parking

brake switch.

Yellow/black

If you use a cellular telephone, connect it via the

Audio Mute lead on the cellular telephone. If not,

keep the Audio Mute lead free of any connections.

Blue (7*)

To Auto-antenna relay control terminal

(max. 300 mA 12 V DC).

Blue/white

To system control terminal of the power amp

(max. 300 mA 12 V DC).

Violet/white

See the section “When connecting

with a back-up camera”.

Fig. 4

When connecting to separately sold power amp

7

Connecting the Units

Blue/white

To system control terminal of the power amp

(max. 300 mA 12 V DC).

This product

Front output

(FRONT OUTPUT)

Subwoofer output

(SUBWOOFER OUTPUT)

Rear output

(REAR OUTPUT)

15 cm

23 cm

15 cm

Center output

(CENTER OUTPUT)

23 cm

Noise filter

(small)

Lock tie

See the section “Attaching the

noise filters”.

English

Español

Deutsch

Français

Italiano

Nederlands

Fig. 5

8

Power amp

(sold separately)

Power amp

(sold separately)

Power amp

(sold separately)

System remote control

RCA cables

(sold separately)

Front speaker

Rear speaker

Subwoofer

Front speaker

Rear speaker

Center speaker

Left Right

Perform these connections when using

the optional amplifier.

Power amp

(sold separately)

9

Connecting the Units

When connecting with a back-up camera

When using this product with a back-up camera, automatic switching to video from a

back-up camera when the gear shift is moved to REVERSE (R) position is possible.

Fig. 6

Connection method

Clamp the lead.1. 2. Clamp firmly with

needle-nosed

pliers.

We recommend that you use

a camera which outputs

mirror reversed images.

Hide-away unit

Fuse resistor

8 m

Extension lead (supplied)

Back up camera

Violet/white

Of the two lead wires connected to the back

lamp, connect the one in which the voltage

changes when the gear shift is in the REVERSE

(R) position.

RCA cable

(sold separately)

Note:

• It is necessary to set to BACK UP CAMERA in SETUP

when connecting the back-up camera.

15 cm

To video output

This product

English

Español

Deutsch

Français

Italiano

Nederlands

10

When connecting the external video component and the display

Fig. 7

• It is necessary to set to AV INPUT in SETUP when connecting the external video com-

ponent.

When using a display connected to rear video output

This product’s rear video output is for connection of a display to enable passengers in the

rear seats to watch the DVD or Video CD.

WARNING:

• NEVER install the display in a location that enables the Driver to watch the DVD or Video CD

while Driving.

• NEVER connect rear audio output (REAR MONITOR OUT) to sold separately power amp.

Hide-away unit

External video

component

(sold separately)

RCA cables

(sold separately)

Display with

RCA input jacks

RCA cables

(sold separately)

To video input

To audio inputs

To video output

To audio outputs

11

Connecting the Units

Attaching the noise filters

To prevent the noise, use the supplied noise filters correctly.

Hide-away unit

This product

Speaker leads

Other than

speaker leads

Noise filter

(small)

Noise filter

(large)

Noise filter

(large)

Noise filter

(large)

Noise filter

(large)

Lock tie

Noise filter

(small)

Noise filter

(large)

Fig. 8

Installation

12

English

Español

Deutsch

Français

Italiano

Nederlands

Note:

• Before finally installing the unit, connect the

wiring temporarily, making sure it is all connect-

ed up properly, and the unit and the system work

properly.

• Use only the parts included with the unit to

ensure proper installation. The use of unautho-

rized parts can cause malfunctions.

• Consult with your nearest dealer if installation

requires the drilling of holes or other modifica-

tions of the vehicle.

• Install the unit where it does not get in the dri-

ver’s way and cannot injure the passenger if there

is a sudden stop, like an emergency stop.

• Do not place the display in a position where it

will impede the driver’s visibility or affect the

operation of your vehicle’s air bags.

• The semiconductor laser will be damaged if it

overheats, so don’t install the unit anywhere hot

— for instance, near a heater outlet.

• If installation angle exceeds 30° from horizontal,

the unit might not give its optimum performance.

(Fig. 9)

Fig. 9

• To ensure proper heat dissipation of this product,

take special care not to block the cooling fan side

of this product.

• When mounting the hide-away unit, make sure

none of the leads are trapped between the hide-

away unit and the surrounding metalwork or fit-

tings.

• Do not mount the hide-away unit near the heater

outlet, where it would be affected by heat, or near

the doors, where rainwater might splash onto it.

• Before drilling any mounting holes always check

behind where you want to drill the holes. Do not

drill into the gas line, brake line, electrical wiring

or other important parts.

• If the hide-away unit is installed in the passenger

compartment, anchor it securely so it does not

break free while the car is moving, and cause

injury or an accident.

• If the hide-away unit is installed under a front

seat, make sure it does not obstruct seat move-

ment. Route all leads and cords carefully around

the sliding mechanism so they do not get caught

or pinched in the mechanism and cause a short

circuit.

30°

13

Installation

Installing the hide-away unit

Mounting with Brackets

Fig. 10

Mounting with Velcro Tape

Thoroughly wipe off the surface

before affixing the velcro tape.

Fig. 11

DIN Front/Rear-mount

This unit can be properly installed

either from “Front” (conventional DIN

Front-mount) or “Rear” (DIN Rear-

mount installation, utilizing threaded

screw holes at the sides of unit chas-

sis). For details, refer to the following

illustrated installation methods.

Before installing the unit

• Remove the frame and the hold-

er. (Fig. 12)

Pull out to remove the frame and then

loosen the screws (2 × 3 mm) to

remove the holder. (When reattaching

the frame, point the side with a groove

downwards and attach it.)

Fig. 12

Holder

Frame

Screw (2 × 3 mm)

Car mat or chassis

Velcro tape

(large)

Screw

(4 × 8 mm)

Car mat or chassis

Bracket

Tapping screw (4 × 12 mm)

Drill 2 to 2.5 mm diameter holes.

14

English

Español

Deutsch

Français

Italiano

Nederlands

DIN Front-mount

Installation with the rubber bush

1. Decide the position of the side

brackets. (Fig. 13)

When installing in a shallow space,

change the position of side brackets. In

this case, stick conceal tape on parts

that protrude from the dashboard.

Fig. 13

2. Install the unit into the dash-

board. (Fig. 14)

After inserting the holder into the

dashboard, then select the appropriate

tabs according to the thickness of the

dashboard material and bend them.

(Install as firmly as possible using the

top and bottom tabs. To secure, bend

the tabs 90 degrees.)

• After installing the unit into the

dashboard, reattach the frame.

Fig. 14

Rubber bush

Screw

Dashboard

Side bracket

Screw (2 × 3 mm)

182

53

Holder

Conceal tape

Side bracket

Flush surface screw (5 × 6 mm)

15

Installation

DIN Rear-mount

Installation using the screw holes on

the side of the unit

• Fastening the unit to the factory

radio mounting bracket. (Fig.

15) (Fig. 16) (Fig. 17)

Select a position where the screw holes

of the bracket and the screw holes of

this product become aligned (are fit-

ted), and tighten the screws at 2 places

on each side. Use any of binding

screws (4 × 3 mm), binding screws (5

× 6 mm) or flush surface screws (5 × 6

mm), depending on the shape of the

screw holes in the bracket.

*1 Use binding screws (4 × 3 mm) only.

Fig. 15

• When installing in a shallow space,

use the following screw holes. In

this case, stick conceal tape on parts

that protrude from the dashboard.

Fig. 16

*2 If the screw holes of the bracket and the

screw holes of this unit are not aligned, use a

file to widen the screw holes of the bracket to

match up the screw holes on this unit.

Tighten the screws at 2 places on each side.

Fig. 17

Screw

Dashboard or

Console

Factory radio mounting

bracket

*2

*

1

Conceal tape

*

1

*

1

English

Español

Deutsch

Français

Italiano

Nederlands

16

Fixing the front panel

If you do not operate the removing and

attaching the front panel function, use

the supplied fixing screws to fix the

front panel to this unit.

• Fix the front panel to the unit

using fixing screws after remov-

ing the front panel. (Fig. 18)

Fig. 18

Installing the remote control unit

When not using the remote control

unit, secure it with velcro tape to pre-

vent it from moving.

• Thoroughly wipe off the surface

before affixing the velcro tape.

Fig.19

Velcro tape (small)

(hard)

Velcro tape (small)

(soft)

Remote control unit

Fixing screw

1
Contenido
Conexión de las unidades ........................ 1
Conexión al sistema  .......................................... 3
Conexión del cable de alimentación (1) ............ 4
Conexión del cable de alimentación (2) ............ 5
Cuando conecte a un amplificador de 
potencia vendido separadamente ................ 7
Cuando conecte con una cámera de 
vista trasera  ................................................ 9
Cuando conecte el componente externo 
y la pantalla  .............................................. 10
Instalación de filtros de ruido .......................... 11
Instalación ................................................ 12
Instalación de la unidad oculta-alejada  .......... 13
Montaje trasero/delantero DIN ........................ 13
Montaje delantero DIN .................................... 14
Montaje trasero DIN ........................................ 15
Fijación del panel delantero  ............................ 16
Instalación del control remoto  ........................ 16
PRECAUCIÓN:
• PIONEER no recomienda que sea usted
mismo quien instale o revise su pantalla.
La instalación o revisión del producto
puede exponerle a descargas eléctricas u
otros peligros. Solicite que todos los
trabajos de instalación y revisión de su
pantalla los realice el personal de
servicio Pioneer autorizado.
• Asegure todo el cableado con
abrazaderas de cables o cinta para usos
eléctricos. No permita que el cableado
pelado permanezca expuesto.
• No taladre un agujero en el
compartimiento del motor para
conectar el cable amarillo de la unidad a
la batería del vehículo. La vibración del
motor podría estropear el aislamiento
en el punto por donde el cable pasa del
compartimiento de los pasajeros al
compartimiento del motor. Tenga
mucho cuidado para mantener el buen
estado del cable en lo relativo a este
punto.
• Es peligrosísimo dejar que el cable de la
pantalla se enrolle en la base del volante
o en la palanca de cambios. Asegúrese
de instalar la pantalla de forma que ésta
no sea un obstáculo para la conducción.
• Asegúrese de que los cables no
interfieran con partes móviles del
vehículo tales como la palanca de
cambio, el freno de mano o el
mecanismo de deslizamiento de los
asientos.
• No acorte ningún cable. Si lo hace, el
circuito de protección tal vez no
funcione correctamente.
Conexión de las unidades

English

Español

Deutsch

Français

Italiano

Nederlands

2

Nota:

• Esta unidad es para vehículos con batería de 12

voltios y con conexión a tierra. Antes de instalar

la unidad en un vehículo recreativo, camioneta, o

autobús, revise el voltaje de la batería.

• Para evitar cortocircuitos en el sistema eléctrico,

asegúrese de desconectar el cable de la batería ≠

antes de comenzar con la instalación.

• Consulte con el manual del usuario para los

detalles sobre la conexión de la alimentación de

amperios y de otras unidades, luego haga las

conexiones correctamente.

• Asegure el cableado con abrazaderas de cables o

con cinta adhesiva. Para proteger el cableado,

envuélvalo con cinta adhesiva donde éstos se

apoyan sobre las piezas de metal.

• Coloque y asegure todo el cableado de tal manera

que no toque las piezas en movimiento, tal como

la palanca de cambio de velocidades, el freno de

mano, y los pasamanos de los asientos. No

coloque el cableado en lugares que se calientan,

tal como cerca de la salida de un calefactor. Si el

material aislante del cableado se derritiera o se

gastara, habrá el peligro de un cortocircuito del

cableado a la carrocería del vehículo.

• No pase el conductor amarillo a través de un orifi-

cio en el compartimiento del motor para conectar

a la batería. Esto dañará el material aislante del

conductor y causará un cortocircuito peligroso.

• No acorte ningún conductor. Si lo hiciera, la pro-

tección del circuito podría fallar al funcionar

cuando debería.

• Nunca alimente energía a otros equipos cortando

el aislamiento del conductor de alimentación pro-

vista de la unidad y haciendo un empalme con el

conductor. La capacidad de corriente del conduc-

tor se excederá, causando el recalentamiento.

• Cuando reemplace algún fusible, asegúrese de uti-

lizar solamente un fusible del ratio descrito en el

soporte de fusibles.

• Ya que se emplea un circuito único BPTL, nunca

coloque los cables de manera que los conductores

del altavoz estén directamente en conexión a tier-

ra o que el altavoz izquierdo y derecho ≠ sean

comunes.

• Si la toma de clavija RCA en la unidad no se usa,

retire las tapas fijadas al extremo del conector.

• Los altavoces conectados a esta unidad deberán

ser del tipo de alta potencia, teniendo un régimen

mínimo de 50 W y una impedancia de 4 a 8

ohmios. La conexión de altavoces con valores de

impedancia y/o de salida diferentes a los anotados

aquí podrían causar fuego, emisión de humo o

daños a los altavoces.

• Cuando se conecta la fuente de este producto, una

señal de control se emite a través del conductor

azul/blanco y conductor azul. Conecte al control

remoto de sistema de un amplificador de potencia

externo o al terminal de controle de relé de antena

automática del vehículo (máx. 300 mA 12 V CC).

Si el vehículo tiene una antena en vidrio, conecte

al terminal de suministro de energía de la antena.

• Cuando se está utilizando un amperio de potencia

externa con este sistema, asegúrese de no conectar

el conductor azul/blanco al terminal de potencia

de amperios. Asimismo, no conecte el conductor

azul al terminal de potencia de la auto-antena. Tal

conexión podría causar la fuga de corriente exce-

siva y causar fallos de funcionamiento.

• Para evitar cortocircuitos, cubra el conductor

desconectado con cinta aislada. Especialmente,

aísle los conductores de altavoz no usados. Hay la

posibilidad de cortocircuito si no se aíslan los

conductores.

• Para evitar la conexión incorrecta, el lado de en-

trada del conector IP-BUS es azul, y el lado de

salida es negro. Conecte los conectores del mismo

color correctamente.

• Esta unidad no se puede instalar en un

vehículo que no dispone de la posición ACC

(accesorio) en el interruptor de encendido.

(Fig. 1)

Fig. 1

• El conductor negro es la masa. Conecte a masa

este conductor separadamente desde la masa de

los productos de alta corriente tal como los ampli-

ficadores de potencia.

Si conecta juntos a masa los productos y la masa

se desconecta, se crea el riesgo de daños a los pro-

ductos o de incendios.

No en la posición ACCPosición ACC

O

N

S

T

A

R

T

O

F

A

C

O

N

S

T

A

R

T

O

F

• Los cables para este producto y aquéllas para

otros productos pueden ser de colores diferentes

aun si tienen la misma función. Cuando se conec-

ta este producto a otro, refiérase a los manuales

de ambos productos y conecte los cables que

tienen la misma función.

3

Conexión de las unidades

Conexión al sistema

Fig. 2

Reproductor de

Multi-CD (vendido

separadamente)

Cable IP-BUS

3 m

Este producto

Entrada IP-BUS

(Azul)

Sintonizador TV oculto-

lejos (GEX-P6400TVP, por

exemplo) (vendido

separadamente)

Entrada AV-BUS (Azul)

Cable AV-BUS (suministrado

con el sintonizador de TV)

Cable IP-BUS

(suministrado con el

sintonizador de TV)

10 cm

Negro

Azul

Negro Azul

Negro

Azul

Cable de 30 clavijas (suministrado)

Cable de 21 clavijas (suministrado)

Violeta

3 m

15 cm

Violeta

Negro

Unidad oculta-alejada

(suministrada)

Jack para antena

Cable de antena (suministrado)

3 m

40 cm

Unidad de navegación

(AVIC-900DVD, por exemplo)

(vendido separadamente)

Cable de 26 clavijas

Amarillo

15 cm

Toma para micrófono

Auto-EQ&TA

Vea el manual de operación.

La page est en cours de chargement...

Pioneer AVH-P7500DVD Le manuel du propriétaire

Pioneer AVH-P7500DVD Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents