LG AB-VP200X Manuel utilisateur

Owner's Manual

MultiVision Mounting Bracket

Please read the safety information carefully before using the product.

AB-VL200X

AB-VP200X

P/NO : MFL63640509 (1112-REV01)

2

Accessories

4 Guide Spacer

Owner's Manual

4 Guide Spacer Fixing

Screws

(M8X32mm)

3 Bracket

Fixing Screws

(M8X100mm)

MultiVision Mounting Bracket-Landscape

AB-VL200X

MultiVision Mounting Bracket-Portrait

AB-VP200X

3 Nuts

Wrench

MultiVision Mounting Bracket

3

ENGLISH

After reading the manual, please keep it handy for future reference.

- If you are a professional installer, please read this manual carefully before installing the product.

- After installing the product according to the manual, ensure that the user also reads the manual carefully.

Safety Precautions

Warning

The product should be installed by a qualified professional

specified by the retail store.

Installing the product without a qualified professional is dangerous and may

cause injury.

The product should be installed where its weight can be

supported.

If the product is installed on a weak surface, the product may fall and cause

injury.

When moving or replacing the product after installation,

contact a qualified installer specified by the retail store.

Installation or movement of the product must be carried out by a skilled

professional. If an unqualified person moves and installs the product, this

may cause safety issues.

Prior to installing the product, arrange the power cable and

signal cable to prevent damage during installation.

Damaged cables may result in a fire, electric shock or damage to the product.

Do not hang on the product or apply shock to the product.

The product may fall and cause injury.

Do not clean the product with wet towels, and do not use a heater or

humidifier underneath the product.

Moisture permeating into the product, including through steam and heat, may

result in a fire, electric shock or damage to the product.

Make sure that the power cord is removed from the outlet before installing

the product.

Otherwise, it may cause an electric shock or a fire.

Keep the product away from sprinklers, sprinkler sensors, high-tension

wires and power sources. Do not install the product in a location where

vibrations or shock impacts are likely to occur.

Wear working gloves when installing the product. Do not use bare hands.

Otherwise, it may cause injury.

Caution

Follow the instructions in the manual to install the product.

If you do not follow the instructions, the product may not be installed properly,

causing serious injury or damage to the product.

To install or adjust the height of the product, two or more people are

needed.

If you try to install or move the product alone, it may fall and cause injury or damage to

the product.

Before installing the product, check whether the wall is strong enough to

hold the product.

Installing the product on a wall that cannot hold its weight may cause safety issues.

When sets are built in to a wall, the internal temperature may rise to such an extent that it

causes overheating, which may lead to a fire. To prevent the set from overheating, please

follow the instructions below.

Avoid completely sealed installation.

To ensure adequate ventilation, keep the top, the bottom and the sides of the set a

minimum of 20 cm from the wall. (The back of the set should be a minimum of 15 cm

from the wall.)

If there is not enough space, a separate ventilation device is required.

If you install four or more sets on top of one another, you will need to ensure a ventilator is

used. (for example, a forced draft fan.)

20cm

15cm

4

When moving or lifting the monitor, read the

following to prevent the monitor from being

scratched or damaged and for safe transportation

regardless of its type and size.



It is recommended to move the monitor in

the box or packing Cover that the monitor

originally came in.



Before moving or lifting the monitor,

disconnect the power cord and all cables.



Hold the top and bottom of the monitor frame

firmly. Make sure not to hold the transparent

part, speaker, or speaker grill area.



Avoid touching the screen at all times, as this

may result in damage on the screen.

CAUTION



When transporting the monitor, do not expose

the monitor to jolts or excessive vibration.



When transporting the monitor, keep the

monitor upright, never turn the monitor on its

side or tilt towards the left or right.



When transporting the monitor by hand,

hold the monitor as shown in the following

illustration.



When the product is carried upright, 2 persons

carry by holding the bottom and top of the

front, and when it is being put down, put down

carefully for the panel not to be touched.



When the product is carried laid down, 2

persons carry by holding the bottom of the

back, and when it is being put down, put down

carefully for the panel not to be touched.

Transportation method for panel protection

5

ENGLISH

Panel

Cushion

If the product needs to be

set upright, hold both sides

of the product, and tilt back-

ward carefully for the panel

not to touch the floor. (The

setting upright of the set is

possible with the outer frame)

When laying down the prod-

uct, lay a cushion on a flat

floor, and put the product on

it with the panel of the prod-

uct facing down.

Panel

If the product is tilted to the

side of the panel, the bottom

of the panel may be dam-

aged.

If the product is tilted to the

edge of the panel, the edge

of the panel may be dam-

aged.

 Handle the product with care. The product may be damaged by shocks.

NOTE

Storage method for panel protection

6

How to Install

Attach the brackets using two bracket fixing screws (M8 x 100mm) and nuts. The procedure is based on 2X2 installation.

Assembling the MultiVision Bracket

1

Nut

Before Installation

* Do not use this product for purposes other than to attach the monitor to the wall.

* Be careful when installing and using the bracket to prevent product damage and safety hazards.

* If the instructions in the manual are unclear, stop the installation and contact the service center.

If you are still having problems understanding the instructions after contacting the center, seek a professional to install the product.

* An individual with experience in mechanical and architectural fields may not have any difficulty understanding this manual or installing the product,

even if they are not a professional.

* When installing the bracket on a concrete wall or on any other walls capable of holding the strength specified in the manual, you may detach the

standard gap bracket for stud wall mounting then follow the instructions for attaching the bracket to make the installation easier.

* Only install the bracket on vertical walls. Do not install the bracket on a wall inclined at an angle, exceeding the standard range or on the ceiling. LG

Electronics is not liable for problems that occur due to the installation of the product on a slanted wall or on the ceiling.

* Check the accessories provided with the product before installing. LG Electronics is not liable for any damage to or loss of the accessories after the

package has been opened.

* Make sure that the accessories are kept out of reach of children to prevent safety accidents, such as choking due to swallowing small parts.

* Make sure that the screws are fixed tightly. Applying excessive force to screws may impair the performance or reduce the strength of the product, or

cause it to become damaged.

* Make sure that the monitor to be installed does not exceed the specified tension load and that no external force is applied.

* In order to prevent accidents, take care when handling tools during installation of the product.

Philips screwdriver (manual or electric)/8mm spanner/drill/level meter

Bracket Fixing Screw

(M8 x 100mm)

The illustration depicts a landscape installation, but the procedure is identical to that of a portrait installation.)

 Check the direction of the arrows shown in the figure above to avoid placing the bracket upside down.

CAUTION

7

ENGLISH

r

MultiVision Wall Bracket-Landscape

AB-VL200X

MultiVision Wall Bracket-Portrait

AB-VP200X

Refer to the following illustration to fix the brackets according to the type.

2

Verifying Where the Brackets Are Fixed

A bolt

The bracket may be distorted, depending on the

flatness of the wall. Adjust the flatness of the bracket

using the A bolts attached to it.

Use a bolt that is capable of holding the weight of the product.

(The combined weight of the set and the bracket is approx. 50kg.

We recommend using an bolt & Nut.)

3

Attaching the Guide Spacers

If the screws are not fully tightened when you fix the guide spacers, check the length of the screws and refer to the technical

service manual.

Fix the guide spacers and the guide spacer fixing screws in the order shown in the picture.

Lay the set down and fix the guide spacers to the set using the screws.

- Place the product on a table with its screen facing downward. Make sure that you place it on soft clothing or a cushion on the flat surface

to protect the screen.

- Tighten the screw until the set, the guide spacer and the screw are joined together securely.

- Use a Philips driver (manual or electric) to tighten the screws.

Guide Spacer

4 Guide Spacer Fixing Screws (M8X32mm)

8

5

6

How to Attach the Product and Bracket

Connecting Cables

- Two or more people are needed to install the product.

- It is recommended to arrange cables using the bracket firat to install the set.

- For information on how to connect cables, please refer to the set's owner's manual.

Place the product assembled with the guide spacers, as illustrated with the arrow.

- Make sure that the product is fixed securely by checking attachement.

4

Dip switch setting

OFF

ON

1

234

1

234

1234 1234

monitor #3

1234 1234

monitor #4

1234 1234

monitor #5

1234 1234

monitor #1

monitor #2

Factory reset

DVI-D OUT DVI-D IN

RGB OUT

RGB IN

SPEAKER

(8)

(SERVICE ONLY)

USB

HDMI 2

HDMI1/DVI

COMPONENT IN

RX TX

1

9

ENGLISH

7

Set Arrangement

The procedure is based on 3X3 installation.

Set Arrangement step : 8 → 5 → 2, 7 → 4 → 1, 9 → 6 → 3

1. Mount set 8, then loosen the horizontal alignment screws to lower the set by approximately 30mm.

(Caution: Otherwise, when set 5 is mounted the sets may collide and cause damage.)

Once the set is lowered, use the horizontal alignment screws to align the set horizontally. Tighten the right/left

screws.

7

9

46

1

3

8

5

2

Loosen the screw to lower the set.

(Loosen the right and left screws gently in turn.)

Tighten the screws to fix the left and right slides.

10

2. Mount set 5, then remove the module-protecting Cover on sets 8 and 5.

Insert Guide pins as shown in the ﬁ gure below.

3. Loosen the horizontal alignment screws on bracket 5, then attach set 5 to set 8.

(Caution: Loosen the right and left horizontal alignment screws gently in turn to prevent the set from tilting and causing damage.)

Fasten the right and left slides of set 5 using the right/left ﬁ xing screws.

Remove the module-protecting Cover.

(The protective Cover is attached on all four sides; only re-

move ﬁ rst the Cover on the sides where the sets meet.)

5

8

Loosen the screw to lower the set.

(Loosen the right and left screws gently in turn.)

Tighten the screws to fix the left and right slides.

Stopper

Push the top set to the bottom set until the stopper slightly

touches the bottom set. Pushing the product with force may

cause damage to the product.

4

CAUTION

 Loosen the left and right leveling screws slowly in turns. Otherwise, this may make

the set tilted, which may cause damage to the set.

11

ENGLISH

Insert Guide pins as shown in the ﬁ gure below.

- Mount set 2 in the same way as set 5 is mounted.

4. Mount set 2, then remove the module-protecting Cover attached between set 5 and 2.

5. Loosen the horizontal alignment screws on bracket 2, then attach set 2 to set 5.

(Caution: Loosen the right and left horizontal alignment screws gently in turn to prevent the set from tilting and

causing damage.)

Fix the right and left slides of set 2 using the right/left ﬁ xing screws.

Remove the module-protecting Cover.

(The protective Cover is attached on all four sides; only

remove ﬁ rst the Cover on the sides where the sets meet.)

8

5

2

Loosen the screw to lower the set.

(Loosen the right and left screws gently in turn.)

Tighten the screws to fix the left and right slides.

12

8

5

2

6. Use the guide ﬁ xers provided to attach sets 2, 5 and 8 as shown below and align them side by side so that no set

sticks out at the front or back.

7. Mount set 9 then adjust its height using the horizontal alignment screws so that set 9 and set 8 are at the same

height.

(Caution: Before mounting the set, push bracket 7 to the left end to ensure there is enough space for set 8.)

<REAR>

8

5

2

9

13

ENGLISH

8. Mount set 6, then remove the module-protecting Cover from sets 9 and 6.

9. Loosen the horizontal alignment screws on bracket 6, then attach set 6 to set 9.

(Caution: Loosen the right and left horizontal alignment screws gently in turn to prevent the set from tilting and

causing damage.)

Insert Guide pins as shown in the

ﬁ gure below.

Remove the module-protecting Cover.

(The protective Cover is attached on all four sides; only remove

ﬁ rst the Cover on the sides where the sets meet.)

<REAR>

8

5

2

9

6

8

5

2

9

6

14

10. Mount set 3, then remove the module-protecting Cover in the same way.

Loosen the horizontal alignment screws on bracket 3, then attach set 3 to set 6.

(Caution: Loosen the right and left horizontal alignment screws gently in turn to prevent the set from tilting and

causing damage.)

Remove the module-protecting Cover.

(The protective Cover is attached on all

four sides; at this point, only remove the

Cover on the sides where the sets meet.)

11. Use the guide ﬁ xers provided to attach sets 3, 6 and 9 as shown below so that the sets are aligned in a perfectly

straight line.

1

-

1

<REAR>

8

5

2

9

6

3

8

5

2

9

6

3

15

ENGLISH

Remove the module-protecting Cover. Remove the module-protecting Cover.

12. Mount sets 1 , 4 and 7 in the same way as sets 3, 6 and 9 are mounted.

- Sets 2, 5 and 8 are ﬁ xed with the right/left ﬁ xing screws; sets 1, 4 and 7 and 3, 6 and 9 are not ﬁ xed with the right/

left ﬁ xing screws and can slide to the right or left.

13. Remove the module-protecting Cover before aligning the sets.

14. Push sets 3, 6 and 9 to the right to meet sets 2, 5 and 8.

Similarly, push sets 1, 4 and 7 to the left to meet sets 2, 5 and 8.

(Caution: Push gently and slowly to avoid damage due to a collision.)

15. Once the sets meet, tighten the right and left ﬁ xing screws for sets 1, 4 and 7 and sets 3, 6 and 9 to prevent

them from sliding.

<REAR>

8

5

2

9

6

3

7

4

1

8

5

2

7

4

1

9

6

3

7

9

46

1

3

8

5

2

16

Remove the module-protecting Cover.

16. Attach additional ﬁ xers to the marked areas to make sure that sets do not stick out at the front or back.

17. Finally, remove all the module-protecting Cover on the outside of the sets.

<REAR>

8

5

2

9

6

3

7

4

1

17

ENGLISH

Product Specifications

Model Name

AB-VL200X AB-VP200X

Width (mm) 1426 1426

Height (mm) 210 210

Depth (mm) 1006 1006

Weight (kg) 22.6 22

The model name and serial number are located on

the back and side of the product.

Please make a note of these below.

Model Name

Serial Number

Manuel d'utilisation

Cadre de ﬁ xation MultiVision

Veuillez lire attentivement les informations relatives à la sécurité avant d'utiliser le

produit.

AB-VL200X

AB-VP200X

2

Accessoires

4 Guide

d'espacement

Manuel d'utilisation

4vis de fixation pour les

guides d'espacement

(M8 X 32mm)

3vis de fixation

du cadre

(M8 X 100mm)

Cadre de ﬁ xation MultiVision – Paysage

AB-VL200X

Cadre de ﬁ xation MultiVision – Portrait

AB-VP200X

3écrous

Clé

Cadre de fixation MultiVision

La page charge ...

LG AB-VP200X Manuel utilisateur

Ce manuel convient également à

LG AB-VP200X Manuel utilisateur

dans d''autres langues

Documents connexes