Yealink CP960 Guide de démarrage rapide

English | Deutsch | Español | Français

HD IP Conference Phone

CP960

Quick Start Guide (V84.10)

www.yealink.com

Applies to firmware version 73.84.0.1 or later.

Table of Contents

English ............................................................ 1

Deutsch .........................................................13

Español ..........................................................25

Français .........................................................37

IP Phone

Quick Start Guide

Power Cord

Ethernet Cable (2m

CAT5E FTP cable)

X 2

Package Contents

Assembling the Phone

Ethernet Cable (7.5m

CAT5E UTP cable)

CP Wireless Expansion Mic CPW90

(Optional)

PoE Adapter

(Optional)

Wireless Expansion Mic

Charging Cradle

0.3m

Micro USB Cable

Quick Start Guide

PSE

Note: The CPW90 helps you to expand the audio range of the IP phone. For more information, refer to Yealink CPW90 Quick Start Guide.

We recommend that you use the accessories provided or approved by Yealink. The use of unapproved third-party accessories may

result in reduced performance.

Note: The IP phone should be used with Yealink original PoE adapter (54V/0.56A) only. The use of the third-party PoE adapter may cause the

damage to the phone.

The cable should be replaced at once if its skin is broken.

1

E

N

G

L

I

S

H

1a. Connect the power and wired network.

Refer to Wireless Network Connection mentioned

below in Configuring Your Phone for more information.

7.5m

2m

1b. Connect the power and wireless network.

7.5m

Wi-Fi

E

N

G

L

I

S

H

2

2. Connect the

optional PC

.

3. Connect the

optional external speaker.

PC

4. Connect the optional

USB flash drive.

Micro USB Port

After the IP phone is connected to the network and supplied with

power, it automatically begins the initialization process. After startup,

the phone is ready for use. You can configure the phone via web user

interface or phone user interface.

Startup

3

E

N

G

L

I

S

H

Hardware Component Instructions

Microphone

Mute Indicator LED

Speaker

Touch Screen

Volume(+) Touch Key

Home Touch Key

Volume(-) Touch Key

Microphone

Network Port

USB Port

Micro USB Port

3.5mm Audio-out Port

Security Slot

Using the Touch Screen

Home Screen

DSS Key Screen

Status Bar

Digital Clock

Applications

Screen

Indicator

Shortcut

Keys

DSS key list

Tap to configure a

DSS key

Swipe left or right to switch between two idle screens.

Control Center and Notification Center

Swipe down from the top of the screen to enter the control center and the notification center.

Time and Date

Drag the slider to adjust the screen

brightness

Display notifications

Entering and Updating Data

To use onscreen keyboard:

1. Tap the input field, the onscreen keyboard displays on the touch screen.

Tap to switch to the uppercase input mode.

Tap to switch to the numeric&symbolic input

mode.

Wireless Mic icon and the number of

connected wireless microphones

Tap the icon to turn the function on or off

quickly

Swipe left or right to delete a notification

Tap to clear all notifications

Tap to backspace.

Label automatically to identify the

context-sensitive features.

• Tap Send to dial out the number.

• Tap Done to confirm the settings.

• Tap Next to go to next field.

• Tap Go to browse the web page.

4

E

N

G

L

I

S

H

Account Settings: Click on Account->Register.

Parameters of the account:

Register Status: It shows the register status of the current account.

Line Active: You can select Enabled/Disabled to enable/disable the account.

Label: It is shown on the touch screen to identify the account.

Display Name: It is shown as Caller ID when placing a call.

Register Name: It is an authenticated ID for authentication provided by ITSP (required).

User Name: It is provided by ITSP for registration (required).

Password: It is provided by ITSP for registration (required).

Server Host: It is provided by ITSP for registration (required).

Register status icons on the touch screen:

Configuring via phone user interface

Network Settings:

1. Tap Settings->Advanced Settings (default password: admin) ->Network->WAN Port/Wi-Fi

Port/VLAN/Webserver Type/802.1x/VPN/LLDP/CDP/NAT to configure the network.

Wireless Network Connection:

1. Tap Settings from the Home screen.

2. Tap Wi-Fi from the Basic Settings block.

3. Turn Wi-Fi on.

The button turns to green, and the phone will automatically search for available wireless networks in your area.

4. Tap an available wireless network from the list of networks.

5. If the network is secure, enter its password in the Password field.

6. Tap Connect to connect to the wireless network.

Account Settings:

1. Tap Settings->Advanced Settings (default password: admin) ->Accounts to configure the account.

Configuring via web user interface

Accessing the web user interface:

1. Tap Settings->General to obtain the IP address of the phone.

2. Open a web browser on your computer, enter the IP address into the address bar (e.g., "http://192.168.0.10" or

“192.168.0.10”), and then press Enter.

3. Enter the user name (default: admin) and password (default: admin) in the login page and click Confirm.

Network Settings: Click on Network->Basic->IPv4 Config

You can configure the network settings in the following ways:

DHCP: By default, the phone attempts to contact a DHCP server in your network to obtain its valid

network settings, for example, IP address, subnet mask, gateway address and DNS address.

Static IP Address: If the phone cannot contact a DHCP server for any reason, you need to configure IP

address, subnet mask, gateway address, primary DNS address and secondary DNS address for the phone

manually.

Configuring Your Phone

Note: The IP phone also supports IPv6, but IPv6 is disabled by default.

The wrong network settings may result in inaccessibility of your phone and may have an impact on the network performance. Contact your

system administrator for more information.

(Green) Registered

(Gray) Register Failed

(Green and Flashing) Registering

Note:

Check with your system administrator if any error appears during the registration process or a specific configuration is required for your

registration.

5

E

N

G

L

I

S

H

Placing a Call

You can place a call by manually entering a phone number, or to a contact from Directory or History.

From the Home screen, do one of the following:

• Tap Dial, enter the phone number, and then tap Send.

• Tap Directory/History, and then tap a desired entry to dial out.

Answering a Call

Tap Answer.

Ending a Call

Tap End Call.

Call Mute and Unmute

To mute a call:

Tap Mute on the touch screen or tap during a call. The mute key LED illuminates solid red.

To unmute a call:

Tap Mute on the touch screen or tap again to unmute the call. The mute key LED illuminates solid green.

Call Hold and Resume

To hold a call:

Tap More->Hold during a call.

To resume a call:

Tap More->Resume or tap during a call.

Local Conference

You can host a five-way conference with up to four parties.

To initiate a conference:

1. Tap during a call.

2. Tap Call multiple members? Click here>>.

3. Enter a phone number, and then tap Add members.

You can also select a contact from Directory or History to join into a conference.

4. Repeat the step 3 to join more members.

5. Tap to call the added members.

The members are added to the conference after answering.

To join two calls into conference:

Tap on the Calls screen.

To manage the individual participant:

Tap the avatar of desired participant, do the following:

• Tap Far Mute to mute the participant. The muted participant can hear everyone, but no one can hear the muted

participant.

• Tap Hold/Resume to hold/resume the participant.

• Tap Split to split the participant from the conference.

• Tap Remove to remove the participant from the conference.

• Tap Detail to view the participant information.

Call Recording

You can record audio calls in the phone itself or onto a USB flash drive (if connected).

To record audio calls:

1. Tap during a call or conference.

2. If a USB flash drive is connected, select where to save your recordings.

The record icon changes to , the record duration and a mark flag appear on the touch screen.

3. If you want to make a mark during the recording, tap Mark once, then the LCD screen will show Mark+1,

meaning that there is one mark in this recording.

4. Tap . The recording is saved.

If you end a call or conference during recording, the recordings will be saved automatically when ending the call.

Call Forward

You can forward an incoming call to a contact, or forward all incoming calls to a contact.

Basic Call Features

Resume

Merge calls

6

E

N

G

L

I

S

H

To forward an incoming call to a contact:

1. Tap from the Incoming Call screen.

2. Enter the number you want to forward to.

You can also select a contact from Directory or History. The call is forwarded to the contact directly.

3. Tap Forward.

To forward all incoming calls to a contact:

1. Tap Settings from the Home screen.

2. Select Call Forward from the Features block.

3. Select the desired forwarding type:

Always Forward----Incoming calls are forwarded unconditionally.

Busy Forward----Incoming calls are forwarded when the phone is busy.

No Answer Forward----Incoming calls are forwarded if not answered after a period of time.

4. Turn on the desired forwarding type.

5. Enter the number you want to forward to in the Forward to field.

6. If you select No Answer Forward, tap the After Ring Time field to select a desired ring time to wait before

forwarding.

7. Tap to accept the change.

Call Transfer

You can transfer a call in the following ways:

Blind Transfer

1. Tap More->Transfer during a call. The call is placed on hold.

2. Enter the number you want to transfer to. You can also select a contact you want to transfer to from Directory or

History.

3. Tap Transfer.

4. Tap Transfer from the prompt box.

Semi-Attended Transfer

1. Tap More->Transfer during a call. The call is placed on hold.

2. Enter the number you want to transfer to.

3. Tap Transfer.

4. Tap Send from the prompt box.

5. Tap Transfer when you hear the ring-back tone.

Attended Transfer

1. Tap More->Transfer during a call. The call is placed on hold.

2. Enter the number you want to transfer to.

3. Tap Transfer.

4. Tap Send from the prompt box.

5. Tap Transfer when the second party answers.

Local Directory

To add a contact:

1. Tap Directory from the Home screen.

2. Tap .

3. Enter a unique contact name in the Name field and contact numbers in the corresponding fields.

4. Tap to accept the change.

To edit a contact:

1. Tap Directory from the Home screen.

2. Tap after the desired contact.

3. Edit the contact information.

4. Tap to accept the change.

To delete a contact:

1. Tap Directory from the Home screen.

2. Tap after the desired contact and then tap Delete.

3. Tap OK when the touch screen prompts “Delete selected item?”.

Note:

You can add contacts from call history easily. For more information, refer to Call History.

Customizing Your Phone

7

E

N

G

L

I

S

H

Call History

1. Tap History from the Home screen.

2. Tap All Local Calls, and then select the desired call history list.

3. Drag up and down to scroll.

4. Tap after the desired entry, and then you can do the following:

• Tap Send to place a call.

• Tap Place on dsskey to assign a speed dial DSS key for the entry.

• Tap Add to add the entry to the local directory.

• Tap Edit before calling to edit the phone number of the entry before placing a call.

• Tap Blacklist to add the entry to the blacklist.

• Tap Delete to delete the entry from the list.

Volume Adjustment

• Tap or on the IP phone during a call to adjust the receiver volume.

• Tap or on the IP phone when the phone is idle or ringing to adjust the ringer volume.

• Tap or to adjust the media volume in the corresponding screen.

8

E

N

G

L

I

S

H

9

E

N

G

L

I

S

H

Regulatory Notices

Operating Ambient Temperatures

 Operating temperature: +14 to 122°F (-10 to 50°C)

 Relative humidity: 5% to 90%, noncondensing

 Storage temperature: -22 to +160°F (-30 to +70°C)

Warranty

Our product warranty is limited only to the unit itself, when used normally in accordance with the operating instructions and the system

environment. We are not liable for damage or loss resulting from the use of this product, or for any claim from a third party. We are not

liable for problems with Yealink device arising from the use of this product; we are not liable for ﬁnancial damages, lost proﬁts, claims

from third parties, etc., arising from the use of this product.

DC symbol

is the DC voltage symbol.

Restriction of Hazardous Substances Directive (RoHS)

This device complies with the requirements of the EU RoHS Directive. Statements of compliance can be obtained by contacting

support@yealink.com.

Safety Instructions

Save these instructions. Read these safety instructions before use!

The following basic safety precautions should always be followed to reduce risk of ﬁre, electrical shock, and other personal injury.

General Requirements

 Before you install and use the device, read the safety instructions carefully and observe the situation during operation.

 During the process of storage, transportation, and operation, please always keep the device dry and clean.

 During the process of storage, transportation, and operation, please avoid collision and crash of the device.

 Please attempt not to dismantle the device by yourself. In case of any discrepancy, please contact the appointed maintenance

center for repair.

 Without prior written consent, no organization or individual is permitted to make any change to the structure or the safety design

of the device. Yealink is under no circumstance liable to consequences or legal issues caused by such changes.

 lease refer to the relevant laws and statutes while using the device. Legal rights of others should be respected as well.

Environmental Requirements

 Place the device at a well-ventilated place. Do not expose the device under direct sunlight.

 Keep the device dry and free of dusts.

 Place the device on a stable and level platform.

 Please place no heavy objects on the device in case of damageand deformation caused by the heavy load.

 Keep at least 10 cm between the device and the closest object for heat dissipation.

 Do not place the device on or near any inﬂammable or ﬁre-vulnerable object, such as rubber-made materials.

 Keep the device away from any heat source or bare ﬁre, such as a candle or an electric heater.

 Keep the device away from any household appliance with strong magnetic ﬁeld or electromagnetic ﬁeld, such as a microwave

oven or a refrigerator.

Operating Requirements

 Do not let a child operate the device without guidance.

 Do not let a child play with the device or any accessory in case of accidental swallowing.

 Please use the accessories provided or authorized by the manufacturer only.

 The power supply of the device shall meet the requirements of the input voltage of the device. Pleaseusethe provided surge

protection power socket only.

 Before plugging or unplugging any cable, make sure that your hands are completely dry.

 Do not spill liquid of any kind on the product or use the equipment near water, for example, near a bathtub, washbowl, kitchen

sink, wet basement or near a swimming pool.

Addr: 309, 3rd Floor, No.16, Yun Ding North Road,

Huli District, Xiamen City, Fujian, P.R.C

Tel: +86-592-5702000

Fax: +86-592-5702455

Addr: 309, 3rd Floor, No.16, Yun Ding North Road,

Huli District, Xiamen City, Fujian, P.R.C

Addr: 309, 3rd Floor, No.16, Yun Ding North Road,

Huli District, Xiamen City, Fujian, P.R.C

Tel: +86-592-5702000

Fax: +86-592-5702455

10

E

N

G

L

I

S

H

ENVIRONMENTAL RECYCLING

Never dispose of the device with domestic waste

Ask your Town Council about how to dispose of it in an environmentally friendly way. The cardboarc

box, plastic packaging and player components may be recycled in accordance with prevailing

recycling regulations in your country.

Always adhere to prevailing regulations

Those who fail to do so may be ﬁned or prosecuted in accordance with the law. The crossed out

garbage can that appears on the device means that when it has reached the end of its useful life, it

should be taken to a special waste disposal centre and treated separately to general urban waste.

 Do not tread on, pull, or over-bend any cable in case of malfunction of the device.

 During a thunderstorm, stop using the device and disconnect it from the power supply. Unplug the power plug and the

Asymmetric Digital Subscriber Line (ADSL) twisted pair (the radio frequency cable) to avoid lightning strike.

 If the device is left unused for a rather long time, disconnect it from the power supply and unplug the power plug.

 When there is smoke emitted from the device, or some abnormal noise or smell, disconnect the device from the power supply,

and unplug the power plug immediately. Contact the speciﬁed maintenance center for repair.

 Do not insert any object into equipment slots that is not part of the product or auxiliary product.

 Before connecting a cable, connect the grounding cable of the device ﬁrst. Do not disconnect the grounding cable until you

disconnect all other cables.

Cleaning Requirements

 Before cleaning the device, stop using it and disconnect it from the power supply.

 Use a piece of soft, dry and anti-static cloth to clean the device.

 Keep the power plug clean and dry. Using a dirty or wet power plug may lead to electric shock or other perils.

Troubleshooting

The unit cannot supply power to Yealink device.

There is a bad connection with the plug.

1. Clean the plug with a dry cloth.

2. Connect it to another wall outlet.

The usage environment is out of operating temperature range.

1. Use in the operating temperature range.

The cable between the unit and the Yealink device is connected incorrectly.

1. Connect the cable correctly.

You cannot connect the cable properly.

1. You may have connected a wrong Yealink device.

2. Use the correct power supply.

Some dust, etc., may be in the port.

1. Clean the port.

Contact your dealer or authorized service facility for any further questions.

Contact Information

YEALINK NETWORK TECHNOLOGY CO.,LTD.

309, 3rd Floor, No.16, Yun Ding North Road, Huli District, Xiamen City, Fujian, P.R.C

YEALINK (EUROPE) NETWORK TECHNOLOGY B.V.

Strawinskylaan 3127, Atrium Building, 8th ﬂoor, 1077ZX Amsterdam, The Netherlands

YEALINK (USA) NETWORK TECHNOLOGY CO., LTD.

999 Peachtree Street Suite 2300, Fulton, Atlanta, GA, 30309, USA

Made in China

YEALINK (XIAMEN) NETWORK TECHNOLOGY CO.,LTD

WWW.YEALINK.COM

Declaration of Conformity

We,

YEALINK (XIAMEN) NETWORK TECHNOLOGY CO.,LTD

Address: 309, 3rd Floor, No.16, Yun Ding North Road,

Huli District, Xiamen City, Fujian, P.R.C

DATE: 20th /July/2019

declare that the product

Type: HD IP Conference Phone

Model: CP960

meets the essential requirements and other relevant provisions according to the following EC directive

Directive: 2014/30/EU, 2014/35/EU, RED 2014/53/EU

Conformity

The product complies with the following standards:

Safety : EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013

EMC:EN 55032:2012/AC:2013

EN 55024:2010

EN61000-3-2: 2014

EN61000-3-3: 2013

Radio: ETSI EN 301 489-1 V2.1.1,

ETSI EN 301 489-6 V2.1.1,

ETSI EN 301 489-17 V3.1.1,

ETSI EN 300 328 V2.1.1,

ETSI EN 301 893 V2.1.1,

EN 301 406 V2.2.2

Health: EN 62311:2008

Directive 2011/65/EU and (EU)2015/863 of the European Parliament and of the Council of 8 June 2011 and 4

June 2015 on the restriction of the use of certain hazardous substances in electrical and electronic

equipment(RoHS 2.0)

Directive 2012/19/EU of the European Parliament and of the Council of 4 July, 2012 on Waste electrical and

electronic equipment (WEEE)

Regulation (EC) No.1907/2006 of the European Parliament and of the Council of 18.December.2006 on

Registration, Evaluation, Authorization, and Restriction of Chemicals (REACH)

Richtlinie 2011/65/EU des Europäischen Parlaments und des Rates vom 8. Juni 2011 zur Beschränkung der

Addr: 309, 3rd Floor, No.16, Yun Ding North Road,

Huli District, Xiamen City, Fujian, P.R.C

Addr: 309, 3rd Floor, No.16, Yun Ding North Road,

Huli District, Xiamen City, Fujian, P.R.C

Tel: +86-592-5702000

Fax: +86-592-5702455

11

YEALINK (EUROPE) NETWORK TECHNOLOGY B.V.

Address: Strawinskylaan 3127, Atrium Building, 8th ﬂoor,

1077ZX Amsterdam, the Netherlands

Telephone: +31(0)646111373

Email: [email protected]

NAME: Stone Lu

DATE:

20/July

/2019

TITLE: Vice President

About Yealink

Yealink is a global leading provider of enterprise communication and collaboration solutions, offering video

conferencing service to worldwide enterprises. Focusing on research and development, Yealink also insists on innovation

and creation. With the outstanding technical patents of cloud computing, audio, video and image processing

technology, Yealink has built up a panoramic collaboration solution of audio and video conferencing by merging its

cloud services with a series of endpoints products. As one of the best providers in more than 140 countries and regions

including the US, the UK and Australia, Yealink ranks No.1 in the global market share of SIP phones shipments.

Technical Support

Visit Yealink WIKI (http://support.yealink.com/) for the latest firmware, guides, FAQ, Product documents, and more. For

better service, we sincerely recommend you to use Yealink Ticketing system (https://ticket.yealink.com) to submit all

your technical issues.

YEALINK (XIAMEN) NETWORK TECHNOLOGY CO.,LTD.

Web: www.yealink.com

Addr: 309, 3rd Floor, No.16, Yun Ding North Road, Huli

District, Xiamen City, Fujian, P.R.C

IP-Telefon

Erste Schritte

Netzkabel

Ethernet-Kabel

(2 m CAT5E-FTP-Kabel)

7,5 m

2m

2 x

Verpackungsinhalt

Installation des Telefons

Ethernet-Kabel (7,5 m

CAT5E-UTP-Kabel)

Kabelloses Konferenztelefon-Erweiterungsmikrofon

CPW960 (optional)

PoE-Netzteil

(optional)

Kabelloses

Erweiterungsmikrofon

Ladestation

0,3m

MicroUSB-Kabel

Erste Schritte

PSE

Hinweis: Das CPW90 unterstützt Sie dabei, den Audio-Aufnahmebereich Ihres Konferenztelefons zu vergrößern. Schlagen Sie für weitere

Informationen in der Schnellanleitung für das CPW90 von Yealink nach.

Wir empfehlen, nur von Yealink angebotenes oder zugelassenes Zubehör zu verwenden. Die Verwendung von nicht zugelassenem

Zubehör von Drittanbietern kann sich negativ auf die Leistung auswirken.

1a. Schließen Sie sowohl das Netzkabel als auch das

Ethernet-Kabel an.

Schlagen Sie für weitere Informationen in den

Ausführungen zu Funknetzwerkverbindungen unter

Konfigurieren Ihres Telefons nach.

Hinweis: Das IP-Telefon darf nur mit dem originalen PoE-Netzteil von Yealink (54 V / 0,56 A) betrieben werden. Die Verwendung von PoE-Netzteilen

von Drittanbietern kann zur Beschädigung des Telefons führen.

Das Kabel sollte ersetzt werden, wenn die Kabelummantelung beschädigt ist.

13

D

E

U

T

S

C

H

7.5m

Wi-Fi

1b. Verbinden Sie das Telefon mit der

Stromversorgung und dem WLAN.

PC

MicroUSB-Port

2. Anschluss eines optionalen PCs.

3. Anschluss eines optionalen Lautsprechers.

4. Anschluss eines optionalen USB-Datenträgers.

Nach der Verbindung mit dem Netzwerk und der Stromversorgung

startet das IP-Telefon automatisch den Initialisierungsprozeß. Nach

dem Startvorgang ist das Telefon betriebsbereit. Sie können das

Telefon via Weboberfläche oder Benutzeroberfläche des Telefons

konfigurieren.

Startvorgang

D

E

U

T

S

C

H

14

Mikrofonkapsel

Anzeige-LED Stummschaltung

Anzeige-LED

Stummschaltung

Lautsprecher

Touchscreen

Berührungssensitive

Lautstärketaste (+)

Berührungssensitive Taste Startbildschirm

Berührungssensitive

Lautstärketaste (-)

Mikrofonkapsel

Netzwerk-Port

USB-Anschluss

MicroUSB-Port

3,5 mm Audioausgangs-Port

Sicherheitssteckplatz

Anweisungen zu Hardwarekomponenten

D

E

U

T

S

C

H

15

Verwendung des Touchscreens

Startbildschirm

Direktruftasten-Bildschirm

Statusbalken

Digitale Uhr

Anwendungen

Bildschirm-

anzeiger

Schnellwahl-

tasten

Direktruftasten-Liste

Tippen Sie eine

Direktruftaste an, um

sie zu konfigurieren

Streichen Sie nach links oder rechts, um zwischen zwei Untätigkeitsbildschirmen umzuschalten.

Systemsteuerung und Mitteilungszentrale

Streichen Sie vom oberen Bildschirmrand nach unten, um die Systemsteuerung und die Mitteilungszentrale zu öffnen.

Datum und Uhrzeit

Ziehen Sie den Schieberegler,

um die Helligkeit des

Bildschirms anzupassen

Bildschirmmitteilungen

Daten eingeben und aktualisieren

Verwendung der Bildschirmtastatur:

1. Wenn Sie auf das Eingabefeld tippen, dann wird auf dem Touchscreen eine Bildschirmtastatur eingeblendet:

Tippen Sie hier für die Eingabe

im Großschriftmodus.

Tippen Sie hier, um zwischen

numerischer und symbolischer

Eingabe umzuschalten.

Das Icon für kabellose Mikrofone und die

Anzahl verbundener kabelloser Mikrofone.

Tippen Sie auf ein Icon, um dessen Funktion

umgehend ein- bzw. auszuschalten.

Ziehen Sie nach links oder rechts, um die

Benachrichtigung auszublenden.

Tippen Sie an, um alle Benachrichtigungen

auszublenden.

Tippen Sie an, um das vorhergehende

Zeichen zu löschen.

Automatische Bezeichnung für

kontextsensitive Funktionen.

• Tippen Sie auf Anrufen, um die Nummer anzuwählen.

• Tippen Sie auf Fertig, um die Einstellungen zu bestätigen.

• Tippen Sie auf Weiter, um zum nächsten Feld zu wechseln.

• Tippen Sie auf Los, um sich eine Webseite anzusehen.

D

E

U

T

S

C

H

16

La page est en cours de chargement...

Yealink CP960 Guide de démarrage rapide

Yealink CP960 Guide de démarrage rapide

dans d''autres langues

Documents connexes