Halsey Taylor HACVRBL Le manuel du propriétaire

Halsey Taylor
Marque
Halsey Taylor
Modèle
HACVRBL
Taper
Le manuel du propriétaire
Page 1
HAC8FVRBL-Q*1D
97601C (Rev A - 2/01)
USES HFC-134A REFRIGERANT
HALSEY TAYLOR OWNERS MANUAL
42
51
19
27
20, 21, 22,
23
24,25
26
48, 55, 57
56
58
26
See Fig. 3 (Page 3) For
Push Button Mechanism
47, 10
28
52
29
30
39
31
35
36, 37, 38
40, 41, 54
34
50
32
35
33
49
44, 45,
46, 59
11
12, 13, 18
8
8
43
Page 2
HAC8FVRBL-Q*1D
97601C (Rev A - 2/01)
FIG. 2
*ADA REQUIREMENT
*REQUISITO DE A.D.A.
*EXIGENCE ADA
**When replacing a Model BFC with a new unit
Model HAC, installer must cut 1-1/2 inches from
length of cooler waste line before connecting to trap
(see installation instruction No.7)
**Cuando reemplace un Modelo BFC con una
unidad nueva Modelo HAC el instalador
deberá cortar 1½ pulgadas del largo del tubo
de desagüe del enfriador antes de conectar el
purgador (vea las instrucciones de instalación
No. 7)
**En remplaçant un modèle BFC avec un
nouveau modèle HAC, linstallateur doit
couper 1 1/2 pouce de longueur de la
canalisation résiduaire du refroidisseur avant
de le raccorder au siphon (voir instruction
dinstallation no. 7)
LEGEND/LEYENDA/LÉGENDE
A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT STUB 1-1/2 IN. (38 mm) OUT FROM WALL SHUT
OFF BY OTHERS
SE RECOMIENDA UBICAR EL TUBO CORTO DE CONEXIÓN AL TUBO DE COBRE SIN CHAPAR DE 3/8" DE DIÁM. EXT. A 1-1/2" (38 mm) FUERA
DE LA LLAVE DE PASO EN LA PARED COLOCADA POR TERCEROS.
EMPLACEMENT RECOMMANDÉ D'ALIMENTATION EN EAU PAR TUBE EN CUIVRE NON PLAQUÉ DE 3/8 PO. (9,5 mm) D.E. CONNECTANT UNE
TUYAUTERIE DE 1-1/2 PO. (38 mm) DEPUIS LE ROBINET D'ARRÊT FOURNI PAR D'AUTRES.
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4 O.D. DRAIN
UBICACIÓN RECOMENDADA PARA EL DRENAJE DE SALIDA DE AGUA, DE 1¼ DE DIÁMETRO.
EMPLACEMENT RECOMMANDÉ POUR LE DRAIN DE D.E. 1-1/4" DE SORTIE DEAU.
C = 1-1/4 TRAP NOT FURNISHED**
PURGADOR DE 1¼ NO PROPORCIONADO**
SIPHON 1-1/4 NON FOURNI**
D = ELECTRICAL SUPPLY (3) WIRE RECESSED BOX
CAJA RECESIVA DE ALAMBRES (3) DE SUMINISTRO ELÉCTRICO
BOÎTE ENCASTRÉE DALIMENTATION ÉLECTRIQUE (3) FILS
E = INSURE PROPER VENTILATION BY MAINTAINING 6" (152 mm) (MIN.) CLEARANCE FROM CABINET LOUVERS TO WALL.
ASEGURE UNA VENTILACIÓN ADECUADA MANTENIENDO UN ESPACIO E 6" (152 mm) (MÍN.) DE HOLGURA ENTRE LA REJILLA DE
VENTILACIÓN DEL MUEBLE Y LA PARED
ASSUREZ-VOUS UNE BONNE VENTILATION EN GARDANT 6" (152 mm) (MIN.) ENTRE LES ÉVENTS DE LENCEINTE ET LE MUR.
F = 7/16 BOLT HOLES FOR FASTENING UNIT TO WALL
AGUJEROS DE LAS TUERCAS DE 7/16 PARA SUJETAR LA UNIDAD A LA PARED
TROUS DÉCROUS 7/16 POUR FIXER LAPPAREIL AU MUR
Page 3
HAC8FVRBL-Q*1D
97601C (Rev A - 2/01)
COOLER BACK
SUPPORT DE SUSPENSION
ARRIÈRE DU REFROIDISSEUR
HANGER BRACKET
FIJADOR DE SUSPENSIÓN
SUPPORT DE SUSPENSION
PUSH BAR MECHANISM
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN
AUTHORIZED SERVICE PERSON
HANGER BRACKETS & TRAP
INSTALLATION
1) Remove hanger bracket fastened to back of cooler by
removing one (1) screw.
2) Mount the hanger bracket and trap as shown in Figure 2.
NOTE: Hanger Bracket MUST be supported securely. Add
fixture support carrier if wall will not provide adequate
support.
IMPORTANT:
7 in. (178mm) dimension from wall to centerline of trap must
be maintained for proper fit.
Anchor hanger securely to wall using all six (6) 1/4 in. dia.
mounting holes.
3) Install straight valve for 3/8" O.D. tube.
INSTALLATION OF COOLER
4) Hang the cooler on the hanger bracket. Be certain the
hanger bracket is engaged properly in the slots on the cooler
back as shown in Fig. 4.
5) Loosen the two (2) screws holding the lower front panel at
the bottom of cooler base and two (2) screws at the top.
Remove the front panel and set aside.
6) Connect water inlet line--See Note 4 of General Instructions.
7) Remove the slip nut and gasket from the trap and install
them on the cooler waste line making sure that the end of
the waste line fits into the trap. Assemble the slip nut and
gasket to the trap and tighten securely.
START UP
Also See General Instructions
8) Stream height is factory set at 45-50 PSI. If supply
pressure varies greatly from this, adjust screw, accessible
by removing Item 2, Fig. 3. CW adjustment will raise stream
and CCW adjustment will lower stream. For best adjustment,
stream should hit basin approximately 6-1/2" (165mm) from
bubbler.
FIG. 3
FIG. 4
CAUTION: Cleaning of Bronzetone Models requires special
care. Outer surfaces must be cleaned with a mild detergent or
mixture of vinegar and water only, rinsed and wiped dry.
Abrasive and Acidic cleaners may eventually damage the
Bronzetone finish.
6
10
2
3
4
7
10
53
10
5
1
17
16
15
14
9
WATER FLOW DIRECTION
Page 4
HAC8FVRBL-Q*1D
97601C (Rev A - 2/01)
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
*REPLACE WITH SAME COMPRESSOR USED IN ORIGINAL
ASSEMBLY.
NOTE: All correspondence pertaining to any of the above
water coolers or orders for repair parts MUST include Model
No. and Serial No. of cooler, name and
part number of replacement part.
PRINTED IN U.S.A.
2222 CAMDEN COURT
OAK BROOK, IL 60523
630.574.3500
ITEMIZED PARTS LIST
Item
No.
Part
No.
5
6
7
31
32
33
34
35
22822C
22814C
27295C
22862C
26776C
22854C
26800C
22955C
Panel Color
Stainless Steel
Stainless Steel
Stainless Steel
Stainless Steel
Stainless Steel
Stainless Steel
Stainless Steel
Stainless Steel
COLOR TABLE
PART NO
22897C
45662C
70022C
45663C
See Color Tbl
See Color Tbl
See Color Tbl
26999C
56033C
75500C
100687608640
160270508640
600985451640
40045C
15005C
61313C
50986C
110868642550
31517C
30699C
70018C
31490C
70009C
22899C
38417001
75524C
55996C
45392C
62152C
66202C
See Color Tbl
See Color Tbl
See Color Tbl
See Color Tbl
See Color Tbl
101516143550
100806740570
19037000
35960C
35959C
35768C
66532C
45351C
100147140560
55884C
75588C
22893C
75564C
40022C
31513C
66534C
70002C
55931C
35958C
15009C
56092C
400660943730
100322740560
70682C
45485C
75589C
75583C
Panel - Bottom Dispenser
Button - Push
Screw - Set
Sleeve - Push Button
Panel - Right Side
Panel - Left Side
Panel - Front Push
Cover - Bottom
Washer
Screw - Torx
Button - Plug
Strainer - Bright
Plug - Drain 1-1/2CP
Hex Nut
Retaining - Nut
Regulator
Holder - Regulator
Screw
Power Cord
Fan Blade
Hex Nut - Fan Blade
Fan Motor
Screw - (Fan Motor)
Shroud - Fan
Screw - #8-18 x 3/8 Lg. (Fan Shroud)
Clip (Front and Rear Panels)
Strainer (See "General Instructions")
Bubbler
Condenser
Drier
Panel - Right Rear (Refrig. Unit)
Panel - Right Rear (Left Unit)
Panel - Left Rear (Left Unit)
Panel - Left Rear (Refrig. Unit)
Panel - Front Lower
Stud - Compressor Mtg.
Grommet - Compressor Mtg.
Clip - Compressor Mtg.
Compressor Serv. Pak EM65
Relay
Cover - Relay
Heat Exchanger
Wasteline Assy.
Gasket - Drain
Fitting - Elbow
Nut - Slip Joint 1-1/4
Basin - Stainless Steel
Washer-Locking
Wasteline Assy.
Cold Control
Evaporator Assembly
Screw - #10 x 1/2" Lg. HHSM
Cover-Dispenser Bottom Gray
Overload
Bubbler - Nipple
Tubing - Poly 48" (Cut To Length)
Hanger Bracket (Not Shown)
Gasket
Fitting - Tee 1/4
Tailpiece Assembly
Gasket
Fitting - Elbow 5/16" - 1/4"
ITEM
NO
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
*39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
NS
57
58
59
60
NS
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Halsey Taylor HACVRBL Le manuel du propriétaire

Halsey Taylor
Marque
Halsey Taylor
Modèle
HACVRBL
Taper
Le manuel du propriétaire
Télécharger le PDF
rapport

Documents connexes