Whirlpool GHW9250MQ2 Le manuel du propriétaire

Marque: Whirlpool

Modèle: GHW9250MQ2

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Ce manuel convient également à

_U_ ®

FRONT.LOADING

AUTOMATICWASHER

For questions about features, operation/performance,

parts, accessories or service call: 1-800-253-130t

In Canada, for assistance call: 1-800-461-5681,

for installation and service call: 1-800-807-6777

or visit our website at

www.whirlpooLcom or www.whirlpool.com/canada

LAVEUSE

AUTOMATIQUEA

CHARGEMENT

FRONTAL

Pour des questions h propos des caracteristiques, du fonctionnement/

performance, des pi_ces, accessoires ou service,

composez le 1-800-253-1301.

Pour assistance au Canada, composez le

1-800-461-5681,

pour installation et service, composez le 1-800-807-6777

ou visitez notre site internet h

www.whirlpool.com ou www.whirlpool.com/canada

Table of Contents/Table des matieres .................. 2

4619 70220381

TABLEOFCONTENTS

WASHER SAFETY .......................................................................... 3

INSTALLATION REQUIREMENTS ................................................ 4

Tools and Parts ............................................................................ 4

Options ......................................................................................... 4

Location Requirements ................................................................ 4

Drain System ................................................................................ 6

Electrical Requirements ............................................................... 6

INSTALLATION INSTRUCTIONS .................................................. 7

Remove Transport System .......................................................... 7

Connect the Inlet Hoses ............................................................... 7

Route the Drain Hose ................................................................... 8

Secure the Drain Hose ................................................................. 8

Level the Washer .......................................................................... 8

Complete Installation ................................................................... 8

FEATURES AND BENEFITS .......................................................... 9

WASHER USE ............................................................................... 10

Starting Your Washer ................................................................. 10

Using the Dispenser ................................................................... 11

Pausing or Restarting ................................................................. 12

Changing Cycles, Options and Modifiers .................................. 12

Status Lights .............................................................................. 12

Cycles ......................................................................................... 13

Options ....................................................................................... 14

Modifiers ..................................................................................... 15

Laundry Guide ............................................................................ 16

LAUNDRY TIPS ............................................................................ 16

Loading....................................................................................... t 7

WASHER CARE ............................................................................ 17

Cleaning Your Washer ............................................................... 17

Water Inlet Hoses ....................................................................... 17

Vacation, Storage, and Moving Care ......................................... 17

TROUBLESHOOTING .................................................................. 18

ASSISTANCE OR SERVICE ......................................................... 20

In the U.S.A ................................................................................ 20

In Canada ................................................................................... 20

WARRANTY .................................................................................. 21

TABLEDESMATIERES

S¢CURIT¢: DE LA LAVEUSE ........................................................ 22

EXIGENCES D'INSTALLATION ................................................... 23

Outils et pieces ........................................................................... 23

Facultatif ..................................................................................... 23

Exigences d'emplacement ......................................................... 23

Systeme de vidange ................................................................... 25

Specifications electriques .......................................................... 26

INSTRUCTIONS D'INSTALLATION ............................................. 27

Enlevement du systeme de transport ........................................ 27

Raccordement des tuyaux d'alimentation ................................. 27

Acheminement du tuyau de vidange ......................................... 27

Immobilisation du tuyau de vidange .......................................... 28

Reglage de I'aplomb de la laveuse ............................................ 28

Achever I'installation .................................................................. 28

CARACTI:!:RISTIQUES ET AVANTAGES .................................... 29

UTILISATION DE LA LAVEUSE ................................................... 30

Mise en marche de la laveuse .................................................... 30

Utilisation du distributeur ........................................................... 31

Pause ou remise en marche ....................................................... 32

Changement de programmes, options et modificateurs ........... 32

Temoins lumineux ...................................................................... 33

Programmes ............................................................................... 33

Options ....................................................................................... 35

Modificateurs .............................................................................. 36

Guide de lessivage ..................................................................... 37

CONSEILS DE LESSIVAGE .......................................................... 38

Chargement ................................................................................ 38

ENTRETIEN DE LA LAVEUSE ..................................................... 38

Nettoyage de la laveuse ............................................................. 38

Tuyaux d'alimentation de la laveuse .......................................... 39

Preparation avant des vacances,

un entreposage ou un dem6nagement ...................................... 39

DC:PANNAGE ................................................................................. 39

ASSISTANCE OU SERVICE ......................................................... 42

Aux letats-Unis ............................................................................ 42

Au Canada .................................................................................. 42

GARANTI E ..................................................................................... 43

WASHERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all

safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or

"WARNING." These words mean:

You can be killed or seriously injured if you don't

immediately follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you

what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic

precautions, including the following:

m Read all instructions before using the washer.

mDo not wash articles that have been previously

cleaned in, washed in, soaked in, or spotted with

gasoline, dry-cleaning solvents, other flammable,

or explosive substances as they give off vapors

that could ignite or explode.

m Do not add gasoline, dry-cleaning solvents, or

other flammable, or explosive substances to the

wash water. These substances give off vapors

that could ignite or explode.

mUnder certain conditions, hydrogen gas may be

produced in a hot water system that has not been

used for 2 weeks or more. HYDROGEN GAS IS

EXPLOSIVE. If the hot water system has not

been used for such a period, before using the

washing machine, turn on all hot water faucets

and let the water flow from each for several

minutes. This will release any accumulated

hydrogen gas. As the gas is flammable, do not

smoke or use an open flame during this time.

-, Do not allow children to play on or in the washer. Close

supervision of children is necessary when the washer is

used near children.

-, Before the washer is removed from service or discarded,

remove the door or lid.

-, Do not reach into the washer if the drum, tub or agitator

is moving.

-, Do not install or store the washer where it will be

exposed to the weather.

-, Do not tamper with controls.

-, Do not repair or replace any part of the washer or

attempt any servicing unless specifically recommended

in this manual or in published user-repair instructions

that you understand and have the skills to carry out.

-, See "Electrical Requirements" for grounding instructions.

SAVE THESE INSTRUCTIONS

INSTALLATIONREQUIREMENTS

Assemble the necessary tools and supplies before beginning the

washer installation. The parts supplied are in the washer drum.

Tools needed for connecting the water inlet hoses

• Pliers (that open to 1°/16in. [39.5 mm])

• Flashlight (optional)

Tools needed for installation

• Open end wrench 17 mm and 13 mm

• Level

• Wood block (2" x 4")

• Ruler or measuring tape

Parts supplied:

Pedestal

Are you placing the washer on a pedestal? You may purchase a

pedestal separately for this washer. This pedestal will add about

13 in. (33 cm) to the height of your unit for a total height of

approximately 51 in. (130 cm).

CC>

Beaded strap Transport bolt hole plug (4)

Alternate Parts

Your installation may require additional parts. Ifyou are interested

in purchasing one of the items listed here, call the toll-free

number on the cover or in the "Assistance or Service" section.

If You Have You Will Need to Buy

Laundry tub or Sump pump system (if not already

standpipe taller available)

than 96 in. (2.4 m)

Overhead sewer

Standard 20 gal. (76 L), 30 in. (76.2 cm)

tall drain tub or utility sink and sump

pump (available from local plumbing

suppliers)

Floor drain Siphon break, Part Number 285834;

additional drain hose Part

Number 8318155; and connector kit,

Part Number 285835

Drain hose too 4 ft drain hose extension kit, Part

short Number 285863

Water faucets 2 longer water fill hoses:

beyond reach of 6 ft (1.8 m) Part Number 76314,

fill hoses 10 ft (3.0 m) Part Number 350008

Optional pedestal

To order, call the dealer from whom you purchased your washer

or refer to the "Assistance or Service" section of this manual. Ask

for Part Number LAB2700MQ (White), LAB2700MT (Biscuit) or

LAB2700ML (Pewter).

Stack Kit

Are you planning to stack your DUET° washer and dryer? To do

so you will need to purchase a Stack Kit.

To order, call the dealer from whom you purchased your dryer or

refer to the "Assistance or Service" section of this manual. Ask

for Part Number 8541503.

Selecting the proper location for your washer improves

performance and minimizes noise and possible washer "walk."

Your washer can be installed under a custom counter, or in a

basement, laundry room, closet, or recessed area. (See "Drain

System.")

Companion appliance location requirements should also be

considered. Proper installation is your responsibility.

You will need

• A water heater set to deliver 120°F (49°C) water to the

washer.

• A grounded electrical outlet located within 5 ft (1.5 m) of

where the power cord is attached to the back of the washer.

(See "Electrical Requirements.")

• Hot and cold water faucets located within 4 ft (1.2 m) of the

hot and cold water fill valves, and water pressure of

20-100 psi (137.9-689.6 kPa).

• A level floor with a maximum slope of 1 in. (2.5 cm) under

entire washer. Installing the washer on carpeting is not

recommended.

• A sturdy and solid floor to support the washer with a total

weight (water and load) of 400 Ibs (180 kg).

Do not operate your washer in temperatures below 32°F (0°C).

Some water can remain in the washer and can cause damage in

low temperatures.

Installation clearances

• The location must be large enough to allow the washer door

to be fully opened,

• Additional spacing should be considered for ease of

installation and servicing.

• Additional clearances might be required for wall, door, and

floor moldings.

• Additional spacing of 1 in, (2.5 cm) on all sides of the washer

is recommended to reduce noise transfer.

• Companion appliance spacing should also be considered,

Washer Dimensions

Recommended installation spacing for custom

undercounter installation

The dimensions shown are for the recommended spacing.

Custom undercounter installation - Washer only

Recommended installation spacing for recessed or

closet installation, with or without a pedestal

The dimensions shown are for the recommended spacing.

Recessed area or closet installation

34_

24 in l

(155 o*r 2)

I1"1-_sl,s"_14"I_-

/25 cm) (80 cm) (102 cm)

(310 cm 2).

-- 3"

76 ore)

__(76 ore)

1. Side view - closet or confined area

2. Closet door with vents

Recessed or closet installation - Washer on pedestal

1" _ 27" ---_- _ 1"

/25 cm) (686 cm) /25 cm)

!. Recessedarea

18 rrin'

_=_,=...,¥

16'_ _," _'14"

(25cm) (80cm) /102 era)

2. Side view - closet or confined area

Recommended installation spacing for recessed or

closet installation, with stacked washer and dryer

The dimensions shown are for the recommended spacing.

48 in? *

(310im2)

__ _-

24 in? _

(155 cm 2 )

3" (7.6 cm)

3" (7,6 cm)

_ _ 1" (2,5 cm)

6" (1_.2 crn)

/?:::: :

76"

(193 cm)

L W::::::

5_//'* _ _ 1_**-:_ _ 27"-_ _ 1....

(14 cm) (Z"bcm) 68.6 urn 2.50m

*Min. top and bottom air openings for closet door.

**Externalexhaust elbow requires additional space.

***Wall,door and floormolding may require

additional spacing.

Recommended installation spacing for cabinet

installation

openings in the top are required.

" . ) _7.8 cm)

4 _'" 31½ _!'_,

The dimensions shown are for the recommended spacing.

For cabinet installation, with a door, the minimum ventilation

__ , (22.9crn)

(10.2crn) (80.0crn) (2.5cm) (2.5cm) (68.6crn) (2.5cm)

The washer can be installed using the standpipe drain system

(floor or wall), the laundry tub drain system, or the floor drain

system. Select the drain hose installation method you need. (See

"Alternate Parts.")

30" rain,

(76=2 cml

Standpipe drain system - wall or floor (view I & 2)

The standpipe drain requires a minimum diameter standpipe of

2 in. (5 cm). The minimum carry-away capacity can be no less

than 17 gal. (64 L) per minute.

The top of the standpipe must be at least 30 in. (76.2 cm) high

and no higher than 96 in. (2.4 m) from the bottom of the washer.

Laundry tub drain system (view 1)

The laundry tub needs a minimum 20 gal. (76 L) capacity. The top

of the laundry tub must be at least 30 in. (76.2 cm) above the

floor.

Floor drain system (view 2)

The floor drain system requires a siphon break that may be

purchased separately. (See "Alternate Parts.")

The siphon break must be a minimum of 28 in. (71 cm) from the

bottom of the washer. Additional hoses might be needed.

EtectricaJ Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in

death, fire, or electrical shock.

A 120-volt, 60-Hz., AC-only, 15- or 20-ampere, fused

electrical supply is required. Time-delay fuse or circuit

breaker is recommended. It is recommended that a separate

circuit serving only this appliance be provided.

This washer is equipped with a power supply cord having a

3 prong grounding plug.

To minimize possible shock hazard, the cord must be

plugged into a mating, 3 prong, grounding-type outlet,

grounded in accordance with local codes and ordinances. If a

mating outlet is not available, it is the personal responsibility

and obligation of the customer to have the properly grounded

outlet installed by a qualified electrician.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

Do not ground to a gas pipe.

Check with a qualified electrician if you are not sure the

washer is properly grounded.

• Do not have a fuse in the neutral or ground circuit.

2 ..............

1.3 prong grounding plug

2. 3 prong grounding-type wall receptacle

3. Grounding prong

4. Power supply cord

GROUNDING iNSTRUCTiONS

For a grounded, cord-connected washer:

This washer must be grounded. Unthe event of a

maffunction or breakdown, grounding wHUreduce the

risk of eUectdcaU shock by providing a path of Ueast

resistance for eUectric current. This washer is

equipped with a cord having an equipment-grounding

conductor and a grounding pUug. The pUug must be

pUugged into an appropriate outUet that is properUy

installed and grounded in accordance with aH UocaU

codes and ordinances.

WARNING: Umproper connection of the

equipment-grounding conductor can resuUt in a risk of

eUectric shock. Check with a qualified eUectrician or

serviceman if you are in doubt as to whether the

appliance is properly grounded.

Do not modify the plug provided with the appliance -

if it will not fit the outlet, have a proper outlet installed

by a qualified electrician.

For a permanently connected washer:

This washer must be connected to a grounded metal,

permanent wiring system, or an equipment grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or

lead on the appliance.

There are 4 bolts in the rear panel of the washer that support the

suspension system during transportation. These bolts also retain

the power cord inside the washer until the bolts are removed.

Using a 13 mm wrench, loosen each of the bolts.

Once the bolt is loose, move it to the center of the hole and

completely pull out the bolt, including the plastic spacer

covering the bolt. The power cord will be attached to all

4 bolts inside the washer.

3. Once all 4 bolts are removed, pull the power cord through the

opening of the rear panel and close the hole with the attached

cap.

4. Close the bolt holes with the 4 transport bolt hole plugs.

NOTE: If the washer is to be transported at a later date, call your

local service center.

INSTALLATION

INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install

washer.

Failure to do so can result in back or other injury.

IMPORTANT: Position the washer so that the rear of the unit is

within approximately 3 ft (90 cm) of the final location.

Connect the inlet hoses to the water faucets

Make sure the washer drum is empty.

1. Using pliers, check the tightness of the hose couplings

already attached to the washer.

NOTE: Do not overtighten. Damage to the coupling can result.

2. Attach the hose with the red color indicator to the hot water

faucet. Screw on coupling by hand until it is seated on the

washer.

3. Attach the hose with the blue color indicator to the cold water

faucet. Screw on coupling by hand until it is seated on the

washer.

4. Using pliers, tighten the couplings with an additional

two-thirds turn.

NOTE: Do not overtighten. Damage to the coupling can

result.

Turn on the water faucets and check for leaks.

NOTE: Replace inlet hoses after 5 years of use to reduce the

risk of hose failure. Record hose installation or replacement

dates on the hoses for future reference.

Periodically inspect and replace hoses if bulges, kinks, cuts,

wear, or leaks are found.

Proper routing of the drain hose protects your floors from

damage due to water leakage. Carefully read and follow these

instructions.

The drain hose is connected to your washer.

After the washer is level, use a 17 mm open-end wrench to

turn the nuts on the feet tightly against the washer cabinet.

All 4 feet must be tightened. If the nuts are not tight against

the washer cabinet, the washer may vibrate.

3. Slide the washer to its final location.

4. Confirm the levelness of the washer.

To prevent drain water from going back into the washer:

• Do not straighten the drain hose, and do not force excess

drain hose into standpipe. Hose should be secure, but loose

enough to provide a gap for air.

• Do not lay excess hose on the bottom of the laundry tub.

Floor drain

You may need additional parts. (See Floor Drain under "Alternate

Parts.")

Drape the power cord over the washer top.

Secure the drain hose to the laundry tub leg or standpipe with

the beaded strap provided. (See illustrations 1 and 2.)

If the washer faucets and the drain standpipe are recessed

(see illustration 3), put the hooked end of the drain hose in the

standpipe. Tightly wrap the beaded strap around the water

inlet hoses and the drain hose.

Do not force excess drain hose into the standpipe.

Properly leveling your washer prevents excessive noise and

vibration.

1. Check the levelness of the washer by placing a level on the

top edge of the washer, first side to side, then front to back.

1. Check the electrical requirements. Be sure that you have the

correct electrical supply and the recommended grounding

method. (See "Electrical Requirements.")

2. Check to be sure all parts are now installed. If there is an

extra part, go back through the steps to see which step was

skipped.

3. Check to be sure you have all of your tools.

4. Dispose/recycle all packaging materials.

5. Check to be sure the water faucets are on.

6. Check for leaks around faucets and inlet hoses.

EJectricaJ Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

FaiJure to follow these instructions can result in

death, fire, or eJectrical shock.

7. Plug into a grounded 3 prong outlet.

8. Read "Washer Use."

9. Totest and to clean your washer, measure _/2the normal

recommended amount of powdered or liquid High Efficiency

(HE) detergent. Pour the detergent into the detergent

dispenser. Select NORMAL, and then select HOLD TO

START. Allow the washer to complete one whole cycle.

If the washer is against a wall, move the washer out slightly

before tipping back. If the washer is not level, first prop the

front with a wood block (2" x 4") and adjust the feet as

necessary; then prop the back and adjust feet as necessary.

Repeat this step until washer is level.

FEATURESANDBENEFITS

Woolmark

The wool wash cycle of this machine has been approved by

Woolmark for the washing of machine washable Woolmark

products provided that the products are washed according to the

instructions on the garment label and those issued by the

manufacturer of this washing machine, M0301.

Electronic Controls

Flexible electronic controls are easy to use whether you are a

beginner or an expert.

Smart Dispensers

The Smart Dispensers make your washer truly automatic. This

washer provides a four-compartment dispenser which includes

separate compartments for main wash detergent, fabric softener,

bleach, and auto prewash or auto soak. The dispenser has large

pour zones, is self-cleaning, and can be easily removed. Laundry

products are diluted with fresh water and added to the load at the

proper time in the wash cycle.

Auto Water Level

This washer automatically adjusts water level for best cleaning

and rinsing performance. Two sensors determine load size, load

composition, and suds level, then the sensors adjust the water

level to the proper setting. This eliminates guesswork. The water

level is just right for every wash load size.

Larger Load Size

Since there is no agitator, you can wash larger, bulkier items like a

king-sized bedspread. You are also able to wash more clothes at

one time, which means fewer loads.

Suspension System

To reduce washer "walk" and "off-balance" conditions, your new

washer combines:

• 2 Springs to isolate vibration

• 4 Shock absorbers at the washer base to minimize movement

Stainless Steel Drum

The Stainless Steel drum eliminates corrosion and enables higher

spin speeds for more water extraction, reducing drying time.

High-Efficiency Wash System

Your new front-loading, high-efficiency washer saves time with

fewer, larger loads, and lowers your water and energy bills by

helping conserve resources.

Spin Speeds

This washer automatically selects the spin speed based on the

cycle selected. This factory setting can be changed, however.

This washer offers up to five different spin speed choices.

Heating Element

This washer has a heating element that automatically heats the

water to the best temperature on select cycles. This enables

stepped cleaning, a process in which warm water is brought in

and mixed with detergent first, then the water is heated. The

warm water cleans stains such as blood and eggs, and the

heated water removes oily stains such as perspiration and dirty

mechanical oil. This heater is active in the Sanitary, Whitest

Whites and Heavy Duty cycles, and in the Stain Treat option.

ACCUWASH TM Automatic Tremperature Control

The ACCUWASH TM control electronically senses and maintains a

uniform water temperature. ACCUWASH control regulates

incoming hot and cold water. ACCUWASH control is

automatically turned On when a cycle is selected.

Add A Garment

At the beginning of the Sanitary, Whitest Whites, Heavy Duty,

Normal and Quick Wash cycles, this washer allows an 8-minute

period in which forgotten garments may be added to a load. The

ADD A GARMENT status light will glow during this 8-minute

period.

CATALYST _ Cleaning Action with Direct Injection

This washer channels 100% of the water through the dispensers

to assure thorough rinse-out and mixture of all the additives

before they touch any garments. The water is then sprayed from

the top front onto the center of the load, providing even

distribution and optimum cleaning performance. It is normal for

small amounts of water to remain in the dispensers when the

wash cycle is complete.

Efficient Detergent System

This washer has a specially designed valve that closes during the

wash portion of the cycle so that 100% of the water and

detergent mixture is used on the load. The Efficient Detergent

System ensures that no water or detergent is wasted.

Dynamic Off-Balance Detection

This washer uses two sensors to detect load size and the amount

of off-balance within the load. The suspension system and

controls are specially designed to redistribute the load

automatically.

WASHERUSE

Less Cb

Estimated

Time

Remaining

e Dday Wash

o Prewash

O Auto Soak

• Exit_ Rinse

Options

Super Ho/ / Cold • Exira High

o Hot/Cold _ High

o Warm / Warm Q Medlurfl _ Louder

@ Warm/cold _ Low o Softer

o Cold/Cold o NoSp_ ® Oft

Water Temp Spin Speed End Of Cycle Stgnat

Wash/_ H_ t_r3 S_c_d__

LockU_J_ckC_trd

Fire Hazard

Never place items in the washer that are

dampened with gasoline or other flammable

fluids.

No washer can completely remove oH.

Do not dry anything that has ever had any type of

oit on it (including cooking oits).

Doing so can result in death, explosion, or fire.

WARNING: To reduce the risk of fire, electric shock, or injury to

persons, read the IMPORTANT SAFETY INSTRUCTIONS before

operating this appliance.

The following is a guide to using your washer. Please refer to

specific sections of this manual for more detailed information.

Do not store laundry products on the top surface of this washer.

Vibration is normal during operation.

First Wash Cycle Without Laundry

Before washing clothes for the first time, choose NORMAL cycle

and run it without clothes. After installation, if a complete cycle

has not been run without clothes, use _/2the normal

recommended amount of powdered or liquid High Efficiency (HE)

detergent. This initial cycle serves to ensure the interior is clean

before washing clothes.

1. To load washer

Open the washer door by pulling on the handle. Sort laundry

according to color and type of fabric. Place a load of sorted

clothes in the washer. Do not overload washer. Overloading

can cause poor cleaning.

• The washer can be fully loaded, but not tightly packed,

Washer door should close easily.

• Mix large and small items and avoid washing single items.

Load evenly.

• It is recommended that you wash small items such as

infant socks in a mesh garment bag.

• When unloading garments, occasionally check under the

rubber rim at the front of the tub for small items.

Close the washer door by pushing it firmly until the lock

clicks. The washer door will remain locked during the wash

cycle.

NOTE: After any wash cycle is completed, the door must be

opened and then closed before a new cycle can begin. The

door can be opened only if PAUSE/CANCEL is selected while

the ADD A GARMENT light is glowing or if the cycle has been

canceled. See "To cancel a cycle."

Open the Dispenser Drawer and add laundry products to the

detergent, bleach, or fabric softener compartments. Close

drawer slowly to avoid spills. See "Using the Dispenser."

NOTE: For best performance, use High Efficiency detergents.

The package for this type of detergent will be marked "HE" or

"High Efficiency."

4. Turn on the washer by selecting CONTROL ON. Select one of

the cycles by turning the cycle selector. The indicator light for

the selected cycle will glow. When selecting a wash cycle, the

preset Options, Water Temp, Spin Speed, and Soil Level for

the selected cycle will glow. The display shows the estimated

time remaining. The preset settings provide the

recommended fabric care for the selected cycle. See

"Cycles."

5. Select the desired OPTIONS. Not all options are available

with all cycles. See "Options."

6. Select the desired MODIFIERS. Not all modifiers are available

with all cycles and options. See "Modifiers."

7. If desired, select the END OF CYCLE SIGNAL. The signal is

helpful when you are washing items that should be removed

from the washer as soon as it stops. Select LOUDER or

SOFTER.

8. To begin the wash cycle immediately

Select HOLD TO START.

• Ifyou do not select HOLD TO START within 5 minutes of

choosing a cycle, the washer automatically shuts off.

• When the wash cycle is complete, the CYCLE

COMPLETE status light glows, the door unlocks, and the

wash load can be removed from the washer. The washer

powers down automatically 5 minutes after the cycle is

complete and the CYCLE COMPLETE light goes off. To

power down the washer manually after the wash cycle is

complete, select PAUSE/CANCEL once.

To begin the wash cycle later

Select DELAY WASH until the desired delay time (in hours)

shows in the Estimated Time Remaining display. Select

START. The countdown to the wash cycle will show in the

display window.

{Jsi tl e ...........

> i i , ..... .............

Your new washer has a dispenser drawer with four separate

compartments for your laundry products--two are for detergent,

one is for liquid chlorine bleach, and one is for liquid fabric

softener. Laundry products are diluted and dispensed

automatically at the proper time during the wash cycle, making it

unnecessary for you to return to the washer during the cycle to

add them.

It is normal for small amounts of water to remain in the

dispensers when the wash cycle is complete.

Do not put laundry additives directly into the wash tub. Always

use the proper dispensers when adding laundry products.

Choosing the Right Detergent

For best washing performance, use a High Efficiency (HE), or

low-sudsing, detergent.

To fill dispenser compartments

1. Pull out the dispenser drawer.

2. Add the desired laundry product to the proper compartment.

3. Push in the dispenser drawer carefully and completely (to

avoid spillage).

Dispenser

1. Prewash detergent compartment

2. Separator

3. Main Wash detergent compartment

4. Dispenser release lever

5. Bleach compartment

6. Fabric softener compartment

Prewash detergent compartment

(Number 1 in Dispenser Illustration)

Add detergent to this compartment when using the Prewash

option or Auto Soak. Liquid or powdered detergent may be used

in this compartment. The detergent will automatically be

dispensed during Prewash if the Prewash option is selected or

during the soak time if Auto Soak is selected.

• Using High Efficiency (HE) detergent, add 1/3the

recommended amount to the Prewash compartment and %

the recommended amount to the Main Wash compartment.

Main Wash detergent compartment

(Number 3 in Dispenser Illustration)

Add liquid or powdered detergent to this compartment for your

main wash cycle. The detergent separator must always be in

place, either in the front or back position.

IMPORTANT: If you are using the Prewash option or the Auto

Soak with a wash cycle, powdered detergent must be used in the

Main Wash compartment since liquid detergents may seep out of

the Main Wash compartment during the prewash, soak time, or

delay before the main wash begins.

• Do not fill beyond the "MAX" level.

• Liquid or powdered color-safe bleach may be added to the

Main Wash compartment along with the same type of

detergent, liquid or powdered.

• Liquid detergent: Put the SEPARATOR in the front position,

between the guides, as shown following. There will be no gap

between the bottom of the wash cycle detergent

compartment and the bottom of the separator.

Separator in front position, between guides

!. Separator

2. Guide

Powdered detergent: Put the SEPARATOR in the back

position, behind the guides, as shown following. There will be

a gap between the bottom of the wash cycle detergent

compartment and the bottom of the separator.

,.....................................................................JloPow°=° P°=wAs.3

LIQUI

Separator in back position, behind guides

!. Separator

2. Guide

NOTE: The separator will be in the POWDER (back) position

when shipped from the factory.

Bleach compartment

(Number 5 in Dispenser Illustration)

Add NO MORE THAN 1/3cup (80 mL) liquid chlorine bleach to this

compartment. The bleach will be automatically diluted and

dispensed at the optimum time during the first rinse after the

wash cycle. This compartment cannot dilute powdered bleach.

Always measure liquid chlorine bleach. Use a measuring cup

with a pour spout; do not guess.

Do not fill beyond the "MAX" level. Overfilling could cause

severe garment damage.

Fabric Softener compartment

(Number 6 in Dispenser Illustration)

Add 1/4cup (60 mL) liquid fabric softener to this compartment.

Fabric softener will be automatically dispensed in the final rinse.

• Do not fill beyond the "MAX" level.

, ¢

To pause the washer at any time, select PAUSE/CANCEL

To continue the cycle, select HOLD TO START (for

approximately 1 second).

Not all Options and Modifiers are available with all cycles. Cycles,

Options and Modifiers can be changed anytime before HOLD TO

START is selected.

Options and Modifiers can be changed anytime after HOLD TO

START is selected and before the start of the selected Option or

Modifier.

To cancel a cycle and select a new cycle

1. Select PAUSE/CANCEL twice.

2. Select desired cycle.

3. Select the desired OPTIONS.

4. Select HOLD TO START (for approximately I second) to

restart the washer at the beginning of the new cycle.

To cancel a cycle

1. Select PAUSE/CANCEL twice.

2. The washer powers down, the door unlocks, and clothes can

be removed.

NOTE: If the water level or the temperature is too high, the

washer will drain automatically before the door unlocks.

To change Options or Modifiers after the cycle has started

1. Select PAUSE/CANCEL

2. Select the desired OPTIONS or MODIFIERS.

3. Select HOLD TO START (for approximately 1 second) to

continue the cycle.

To drain the washer manually

1. Select PAUSE/CANCEL

2. Select DRAIN/SPIN.

3. Select HOLD TO START (for approximately 1 second) to

begin the drain.

4. When the spin is complete, the door unlocks. Items can be

removed from the washer.

These lights show which portion of the cycle the washer is

operating. They also indicate when you can add an additional

item to the wash cycle and when the controls are locked.

Status

Q Delay Wash

@ Add a Garment

@ Soak/Prewash

• Wash

@ Rinse

• Spin

O Cycle Complete

@ Control Locked

Adding items

You can add items to the washer after the cycle has started for

Sanitary, Whitest Whites, Heavy Duty, Normal and Quick Wash, if

the ADD A GARMENT status light is glowing.

To add items

1. Select PAUSE/CANCEL. The washer door unlocks, and items

can be added.

2. To continue the cycle, close the door and select HOLD TO

START (for approximately 1 second).

Cycle Complete

The cycle complete light stays on for 5 minutes after the cycle is

complete, and then the washer shuts off.

Locking controls

The Control Lock prevents unintended use of the washer. You

can also use the control lock feature to prevent unintended cycle

or option changes during a cycle. When CONTROL LOCKED is

lit, all buttons are disabled except for PAUSE/CANCEL and

START. You can lock the controls while the washer is operating.

To lock the controls

Select and hold END OF CYCLE SIGNAL for 3 seconds.

O Louder

• Softer

o off

End Ot Cycle Signal

LocMUnlock Cor,tro3

The CONTROL LOCKED status light glows.

To unlock the controls

Select and hold END OF CYCLE SIGNAL for 3 seconds until the

CONTROL LOCKED status light turns off.

Estimated time remaining

The cycle time varies automatically based on your water

pressure, water temperature, detergent and clothes load. The

cycle time will be extended if oversudsing occurs or the load is

unbalanced.

Cycles can be selected by turning the Cycle control knob to the

desired cycle. Each cycle is designed for different types of fabric

and soil levels.

Whitest lAZhites Sanitary

Normo,./;2K,

Oo,,co,oJCasuo,

s,@_ / °Soak

Wool Hand Washables

Each cycle has a preset Soil Level (cycle time), Water

Temperature and Spin Speed, and may have preset options.

The preset settings provide the recommended fabric care for

the selected cycle.

The preset settings can be changed anytime before HOLD TO

START is pressed. Not all options and modifiers are available

with all cycles. (Tochange settings after the cycle has started,

press PAUSE/CANCEL, then select the desired settings.

Press HOLD TO START to continue the cycle.)

Sanitary

Use this cycle to clean heavily soiled, colorfast fabrics. This

cycle combines a super hot water temperature and fast speed

tumbling to help ensure the removal of heavy soils and stains.

It is recommended that you set your hot water heater to 120°F

(49°C) to ensure proper performance during this cycle. The

Sanitary cycle also helps eliminate 99.999% of 3 common

infectious bacteria, even when no bleach is used. Extra high

speed spin helps shorten drying time.

Whitest Whites

This cycle is especially designed for cleaning loads of soiled

white fabrics with the addition of bleach. Hot washing

temperatures assure optimal bleach activity. An additional rinse

provides optimal rinse performance to avoid chlorine residues on

your laundry. This cycle combines fast-speed tumbling, longer

wash time, and extra high speed spin to shorten drying time.

Heavy Duty

Use this cycle to wash loads of sturdy, colorfast fabrics and

heavily to normally soiled garments. This cycle combines

fast-speed tumbling, longer wash time, and extra high speed spin

to shorten drying times. If the water temperature is lower than

needed for this cycle, the heater will warm the water to the

optimum temperature.

NOTE: Use the Heavy Duty cycle for optimal removal of organic

soils such as blood.

Normal

Use this cycle to wash normally soiled cottons and linens. This

cycle combines medium-speed tumbling and high-speed spin.

Bulky Items

Use this cycle to wash large items such as blankets and

comforters. This cycle starts with a soak to thoroughly saturate

your large load. This is followed by medium wash action and

low-speed spin only to maintain load balance.

Quick Wash

Use this cycle to wash small loads of lightly soiled garments that

are needed in a hurry. This cycle combines fast-speed tumbling,

a shortened wash time, and extra high speed spin to shorten

drying time.

Delicate/Casual

Use this cycle to wash no-iron fabrics and garments labeled

"Permanent Press" or "Wrinkle Free" or that indicate using a

"Gentle" cycle on the care label. This cycle combines low-speed

tumbling and low speed spin to reduce wrinkling.

Silk

Use this cycle to clean washable silk garments. (Check label

instructions to make sure that garment is washable.) This cycle

gently tumbles and drains without spinning to gently clean

garments and minimize wrinkling. Because there is no spinning

action, garments will contain a higher amount of water at the end

of this cycle.

Wool

Use this cycle to clean machine washable woolen garments.

(Check the care instructions to make sure that garment is

washable.) This cycle features gentle tumbling and low-speed

spin to provide optimum garment care.

Hand Washables

Use this cycle to clean hand washable and special-care

garments. Similar to the way garments are hand washed in a

sink, the wash action of this cycle combines periods of low-

speed tumbling and soaking. Low-speed spin reduces wrinkling.

Soak

Use the Soak cycle to remove small spots of set-in stains on

fabrics. This cycle provides a soak time with warm or cold water

followed by drain. Extra water, a short tumbling phase for equal

distribution of the laundry, and a soaking time without drum

movement improve the removal of set-in stains. Drain without

spin assures gentle treatment, even for delicate articles.

Rinse/Spin

Use this cycle to get a rinse and spin only. This cycle combines

fast-speed tumbling and extra high speed spin. Ifdesired, you

can reduce the spin speed by selecting the speed you want from

the SPIN SPEED modifier.

A Rinse/Spin cycle is useful for

• Loadsthat need rinsing only.

• Adding fabric softener to a load.

Drain/Spin

Use this cycle to drain your washer or to drain and spin your

wash load. The spin speed is preset to extra high. If desired, you

can reduce the spin speed by selecting the speed you want from

the SPIN SPEED modifier.

NOTE: Loads of synthetics, delicate fabrics, handwashables, and

woolens should be drained with no spin or low spin speed to

avoid fabric stress.

Preset cycle settings

Each cycle has a preset Soil Level (cycle time), Water

Temperature, and Spin Speed. The preset settings provide the

recommended fabric care for the selected cycle. See chart.

Cycle Soil Level Water Temp Spin Speed

(cycle time)

Sanitary Normal Super Hot/Cold Extra High

(1:55)

Whitest Normal Hot/Cold Extra High

Whites (1:00)

Heavy Normal Hot/Cold Extra High

Duty (1:20)

Normal Normal Warm/Cold High

(0:40)

Bulky Normal Warm/Cold Low

Items (0:55)

Quick Less soil Warm/Cold Extra High

Wash (0:30)

Delicate/ Normal Warm/Cold Medium

Casual (0:35)

Silk Normal Cold/Cold No Spin

(0:26)

Wool Normal Cold/Cold Medium

(o:3o)

Hand Normal Cold/Cold Low

Washables (0:30)

Soak Normal Warm/Cold No Spin

(0:30)

Rinse/Spin Normal Cold/Cold Extra High

(0:21)

Drain/Spin Normal N/A Extra High

(0:11)

To change the preset cycle settings

Press the selector of each setting until the desired setting glows.

Normal Washer Sounds

As with any new product, you will hear sounds that you are not

accustomed to. You may hear various sounds when the door is

locked and unlocked, and during the washing, rinsing, and

spinning process. Between changes in wash actions, there will

be momentary pauses. You will hear water spraying and

splashing during the wash and rinse cycles. These new sounds

and pauses are part of normal washer operation.

You can customize your wash by adding "Options" to your cycle

selections. You can add or change an option after starting a cycle

anytime before the selected option begins. Not all options are

available with all cycles.

o Dd_y Wash

Pl_wash

o Ado Soak

Extra R_nse

Options

See the "Laundry Guide" for an overview of possible options

for each Wash Cycle selection.

You can select more than one option for a cycle. Some

options cannot be added to some cycles; for example,

Prewash cannot be added to the Quick Wash cycle.

If an option is available with a selected cycle, the light for that

option will glow when selected.

If an option is unavailable with a selected cycle, there will be a

short tone, and the light for that option will not glow when

selected.

Delay Wash

Use this to begin the wash cycle later.

• Select Delay Wash until the desired time (in hours) shows in

the Estimated Time Remaining display.

• Select START. The countdown to the wash cycle will show in

the display window.

Prewash

Use this option for heavily soiled loads that need pretreatment.

This option adds a 15-minute prewash and drain to the main

wash cycle.

NOTES:

• Add detergent to the Prewash and Main Wash

compartments of the Dispenser Drawer.

• When using Prewash, do not use liquid detergent in the Main

Wash compartment. Use powdered detergent for the main

wash cycle.

NOTE: The Prewash and Auto Soak options cannot be selected

in the same cycle.

Auto Soak

Use the Auto Soak option for loads of heavily soiled cotton, linen,

polyester or nylon with set-in stains. During Auto Soak, water will

be added to the drum and the laundry will be equally distributed

by a short tumbling phase. Laundry will then be soaked by

phases without drum movement. After soaking, the washer

drains without spinning.

• Add detergent to both the Prewash and Main Wash

compartments of the Dispenser Drawer.

• Use powdered detergent for the main wash cycle because

liquid detergent will seep into the washer during Auto Soak.

• For cycles with Hot Wash Temperatures, the Soak

temperature is set to WARM. Otherwise the Soak

temperature is the same as the Wash Temperature.

• The Auto Soak and Prewash options cannot be selected in

the same cycle.

Extra Rinse

An extra rinse can be used to ensure the removal of detergent or

bleach residue from garments. This option provides an additional

rinse with the same water temperature as the first rinse.

Preset cycle settings of Water Temperature, Spin Speed, and

Soil Level can be changed. You can change a modifier after

starting a cycle anytime before the selected modifier begins.

Not all modifiers are available with all cycles and options.

® Super Hot / Cold o Extra High

o Hot/Cold ® High

® Warm / Warm • Medium

o Louder

o Warm/Cold o Low o Softer

• Cold/Cold _ NoSp_n e Off

Water remp Spin Speed End Of Cycle Signal

Wash / Rinse Hold tot 3 Secorlds to

LocMunedk Control

To change the water temperature, select the WATER TEMP

button until the desired setting glows.

To change the spin speed, select the SPIN SPEED button

until the desired setting glows.

To change the loudness of the End of Cycle Signal, select

END OF CYCLE SIGNAL.

More 0

Wash/Rinse Temp

Select a water temperature based on the type of load you are

washing. Use the warmest wash water safe for fabrics. Follow

garment label instructions.

Warm rinses leave the loads dryer than cold rinses. Warm rinses

increase wrinkling. In cold climates, a warm rinse makes the load

more comfortable to handle. Cold rinses save energy.

Temperature Guide

Wash Water Temperature Suggested Fabrics

SUPER HOT Sturdy colorfast fabrics

153°F (67°C) Heavy soils

HOT Whites and pastels

122°F (50°C) or above Heavy soils

WARM Bright colors

104°F (40°C) Moderate to light soils

COLD Colors that bleed or fade

77°F (25°C) Light soils

In wash water temperatures colder than 70°F (21°C), detergents

do not dissolve well. Soils may be difficult to remove.

ACCUWASH TM Automatic Temperature Control

The ACCUWASH TM control electronically senses and maintains a

uniform water temperature. ACCUWASH control regulates

incoming hot and cold water. ACCUWASH control is

automatically turned On when a cycle is selected. (See "Preset

Cycle Settings" in "Cycles.")

• ACCUWASH control ensures consistent cleaning.

• ACCUWASH control works for all wash and rinse temperature

settings.

Estimated

Time

Remaining

Less 0

Soil

Level

• To change cycle time, select SOIL LEVEL button.

_._2_ 3,(:_%_.:_

Refer to this chart for suggested load types and their corresponding cycles. Listed to the right are the options available to each of these

washer cycles.

CYCLE SUGGESTED LOAD TYPE AVAILABLE OPTIONS

Delay Wash Prewash* Auto Soak* Extra Rinse

Sanitary Heavily soiled underwear, towels, work clothes, V' v' V' v'

diapers, etc.

Whitest Whites Heavily soiled white fabrics V' v' V' v'

Heavy Duty Heavily to normally soiled underwear, towels, _ _/ _ _/

shirts, etc.

Normal Normally soiled blouses, shirts, overalls, etc., V' v' V' v'

made of polyester, nylon, cotton, linen, or

cotton blends

Bulky Items Normally soiled blankets and comforters v' v' v' v'

Quick Wash Lightly to normally soiled overalls and sports v' v' v'

wear made of cotton, polyester, nylon and

cotton blends

Delicate/Casual Use this cycle to wash no-iron fabrics and V' v' V' v'

garments labeled "Permanent Press" or

"Wrinkle Free" or that indicate using a "Gentle"

cycle on the care label.

Silk Fabrics made of silk identified as machine _ _/

washable

Wool Woolens with a felt-free finish, identified as v' _/

machine washable

Hand Fabrics made of silk, special-care items v' v'

Washables marked "Handwashable"

Soak Fabrics made of cotton, linen, polyester or

nylon

Rinse/Spin Fabrics made of cotton, linen, polyester or V' v'

nylon

Drain/Spin Fabrics made of cotton, linen, polyester or

nylon

*Prewash and Auto Soak cannot be selected at the same time.

LAUNDRYTIPS

Preparing clothes for washing

Follow these recommendations to help you prolong the life of

your garments.

• Close zippers, snaps, and hooks to avoid snagging other

items. Remove pins, buckles, and other hard objects to avoid

scratching the washer interior. Remove non-washable trim

and ornaments.

• Empty pockets and turn them inside-out.

• Turn down cuffs; brush away lint and dirt.

• Turn synthetic knits inside-out to avoid pilling.

• Tie strings and sashes so they will not tangle.

• Mend tears, loose hems, and seams.

• Treat spots and stains.

• Stained or wet garments should be washed promptly for best

results.

Sorting

• Separate heavily soiled items from lightly soiled ones, even if

they would normally be washed together. Separate lint-givers

(towels, chenille) from lint-takers (corduroy, synthetics,

permanent press). When possible, turn lint-givers inside-out.

• Separate dark colors from light colors, colorfast items from

noncolorfast items.

• Sort by fabric and construction (sturdy cottons, knits, delicate

items).

Unloading

• Remove clothes from washer after the cycle is completed.

Metal objects such as zippers, snaps, and buckles may rust if

left in the washer basket for a long time.

Loading suggestions (maximum size loads).

Heavy Work Clothes

4 jeans 2 sweatpants

4 workpants 2 sweatshirts

4 workshirts

Towels

10 bath towels

10 hand towels

14 washcloths

Mixed Load

3 sheets (1 king, 2 twin) 9 T-shirts

4 pillowcases 9 shorts

3 shirts 10 handkerchiefs

3 blouses

WASHERCARE

Cleaning the exterior

Use a soft damp cloth or sponge to wipe up any spills.

Occasionally wipe the outside of your washer to keep it looking

new. Use mild soap and water. Do not use abrasive products.

Cleaning the interior

Use a soft damp cloth or sponge to occasionally wipe the inner

door to remove any detergent residue. Use mild soap and water.

Do not use abrasive products.

Cleaning the door seal

Use a soft damp cloth or sponge when necessary. Check the fold

of the seal periodically for any foreign objects.

Cleaning the dispenser drawer

The dispenser drawer is removable for easy cleaning.

1. Unlock the dispenser drawer by pressing the Release Lever in

the Prewash compartment. See "Using the Dispenser."

Remove the drawer.

2. Remove the inserts (the siphon from the softener and bleach

compartments and the separator).

3. Wash the parts under running water.

4. Replace the inserts and return the dispenser to the drawer.

Replace inlet hoses after five years of use to reduce the risk of

hose failure. Periodically inspect and replace inlet hoses if

bulges, kinks, cuts, wear or leaks are found.

When replacing your inlet hoses, record the date of replacement.

Install and store your washer where it will not freeze. Because

some water may stay in the hoses, freezing can damage your

washer. If storing or moving your washer during freezing weather,

winterize it.

Non-ues or vacation care:

Operate your washer only when you are at home. If you will be on

vacation or not using your washer for an extended period of time,

you should:

• Unplug washer or disconnect power.

• Turn off the water supply to the washer. This helps avoid

accidental flooding (due to a water pressure surge) while you

are away.

• Slightly open door to provide ventilation.

To winterize washer:

1. Put 1 qt (1 L) of R.V.-type antifreeze in the drum.

2. Run washer on a DRAIN/SPIN cycle.

3. Unplug washer or disconnect power.

4. Shut off both water faucets.

5. Disconnect water inlet hoses from faucets and drain.

To use washer again:

1. Flush water pipes.

2. Reconnect water inlet hoses to faucets.

3. Turn on both water faucets.

4. Plug in washer or reconnect power.

5. Run the washer through the NORMAL cycle with V2the

normal recommended amount of HE detergent to clean out

antifreeze.

To transport the washer:

1. If washer will be moved during freezing weather, put in 1 qt

(1 L) of R.V.-type antifreeze in the drum. Run washer on a

DRAIN/SPIN cycle.

2. Unplug the power cord.

3. Disconnect the drain hose from the drain system and attach

to rear panel clips.

4. Shut off both water faucets.

5. Disconnect the water inlet hoses from faucets, then drain the

hoses and clip them to the rear panel of the washer.

6. IMPORTANT: Call service. Do not reuse transport bolts. Unit

must be transported in the upright position.

Reinstalling the washer

1. Follow the "Installation Instructions" to locate, level and

connect the washer.

2. Run the washer through the NORMAL cycle with V2the

normal recommended amount of HE detergent to clean the

washer and remove the antifreeze, if used.

TROUBLESHOOTING

First try the solutions suggested hers to possibly avoid the

cost of a service call...

Washer displaying code message and tone sounds

• "FH" (Water Inlet Problem--no water or insufficient water

supply)

Select PAUSE/CANCEL twice to cancel the cycle. Unplug

washer or disconnect power.

Check the following:

Are water faucets completely turned on?

Are screens at inlet hose connection to washer clogged?

Are water inlet hoses kinked?

Are water inlet hoses frozen?

Plug in washer or reconnect power. Re-select cycle and press

HOLD TO START. If the problem remains, call for service.

• "F02" (Drain Problem)

Select PAUSE/CANCEL twice to cancel the cycle. Unplug

washer or disconnect power.

Check the following:

Is the drain hose kinked?

Is the drain hose frozen?

Is the drain hose clogged?

Is the drain hose more than 96 in. (2.4 m) above the floor?

• "SUB" (Suds Routine)

When excessive suds are detected, a suds routine

automatically starts. This routine removes extra suds and

assures proper rinsing of your garments. "SUD" is displayed

during rinsing and at the end of the cycle to inform you that

Suds Routine was activated. To avoid excessive sudsing,

use only HE detergents.

• "F" Variables [F4 to F16] (Electrical Problem)

Select PAUSE/CANCEL twice to cancel the cycle. Select

DRAIN/SPIN if there is excessive water in the washer.

Re-select cycle and press HOLD TO START. If the problem

remains, call for service.

Washer won't start

• Checkthe following:

Is the power cord plugged into a grounded 3 prong outlet?

Is the washer door firmly closed?

Has a cycle been selected, but HOLD TO START has not

been selected and held for one second?

Was the door open after completion of last cycle?

Washer won't fill, wash or rinse

• Checkthe following:

Is the power cord plugged into a grounded 3 prong outlet?

Is there power at the plug? Check electrical source or call

electrician.

Are the hot and cold water faucets turned on?

Is the water inlet hose kinked?

Washer stops

• Checkthe following:

Is the power cord plugged into a grounded 3 prong outlet?

Is there power at the plug?

Check electrical source or call electrician.

Has a fuse blown or has the circuit breaker tripped?

If problem continues, call electrician.

Are you using an extension cord?

Do not use an extension cord.

Washer won't drain or spin

• Is the drain hose clogged, or the end of the drain hose

more than 96 in. (2.4 m) above the floor?

• Is your voltage low?

Check electrical source or call electrician. Do not use an

extension cord.

• Is the "SUD" routine active?

Cycle will complete once extra suds are removed.

• Is the load balanced?

A single or bulky item may cause imbalance. Add more items

or redistribute the load.

Washer makes noise or vibrates

Is the washer level?

The washer must be level. The four feet should be properly

installed, and the nuts should be tightened against the

washer cabinet.

As water is drained from the washer, you may hear air being

pulled through the pump. This happens during the end of

draining. It is normal.

Are you washing items with metal snaps, buckles or

zippers?

You may hear metal items touching the washer drum. This is

normal.

Is washer installed on a sturdy and solid floor?

Refer to the "Installation Instructions" for flooring

requirements. Noise and vibration may be reduced by placing

a piece of 3Ain. (19.1 ram) plywood underneath your washer.

The plywood may extend underneath both washer and dryer

to keep them at equal heights.

Washerleaks

• Check household plumbing for leaks.

Are the water inlet valve screens clogged?

Dispenserscloggedorleaking

Are the laundry products in the correct dispenser

compartment?

Add the correct amounts of detergent, fabric softener or

liquid chlorine bleach to the correct compartments. Add

powdered or liquid color-safe bleach to the Main Wash

compartment. Be sure to match powdered color-safe bleach

with powdered detergent or match liquid color-safe bleach

with liquid detergent.

Is the detergent separator in the correct position?

Separator should be in the front position when using liquid

detergent and in the back position when using powdered

detergent.

Load too wet

• Did you use the right cycle for the load being washed?

Select a cycle with a higher spin speed.

Did you wash a single item or bulky items or have you

overloaded the washer?

A single item, bulky items, or overloading may cause

imbalance. Add items or try to evenly distribute your wet

laundry in the drum, and start a DRAIN/SPIN cycle. Ifthe

laundry is still wet, take half of the load out of the washer and

try again.

Residue or lint on load

• Did you add detergent to the dispenser?

For best results, add detergent to the detergent

compartment. Do not add detergent to the washer drum.

Did you sort properly?

Sort lint givers (towels, chenille) from lint takers (corduroy,

synthetics). Also sort by color.

Did you overload the washer?

Do not overload the washer. The washer can be fully loaded,

but not tightly packed. The wash load must be balanced. Lint

can be trapped in the load if overloaded.

Check the following:

Was paper or tissue left in pockets?

Did you use enough detergent?

Follow manufacturer's directions. Use enough detergent to

hold the lint inthe water.

Is your water colder than 70°F (21°0)?

Wash water colder than 70°F (21°C) may not completely

dissolve the detergent.

Are you using a low speed wash cycle?

Powdered detergents may not dissolve well in a slow speed

cycle. For best results, use liquid detergent for slow speed

cycles such as Delicate/Casual, Silk, Wool, and Hand

Washables.

Stains on load

• Did you add detergent to the dispenser?

For best results, add detergent to the detergent

compartment. Do not add detergent to the washer drum.

Did you use enough detergent?

Use enough detergent to remove soil and hold it in suspension.

For best performance, use a High Efficiency detergent.

Follow manufacturer's recommendations for the type of load

you are washing.

Is there above average iron (rust) in water?

You may need to install an iron filter.

Did you properly sort the load?

Sort dark clothes from whites and lights.

Did you unload the washer promptly?

To avoid dye transfer, unload the washer as soon as it stops.

Did you use a fabric softener dispensing ball?

Dispensing balls will not operate correctly with this washer.

Add liquid fabric softener to the fabric softener compartment.

Did you use powdered detergent in a low-speed cycle?

Consider using liquid detergent.

Did you use Quick Wash on a large load?

For best results, use Quick Wash for small, lightly soiled

loads.

Load iswrinkled

• Did you unload the washer promptly?

Unload the washer as soon as it stops.

Did you use the right cycle for the load being washed?

Use the Delicate/Casual cycle or another cycle with a low

spin speed to reduce wrinkling.

Did you overload the washer?

The wash load must be balanced and not overloaded. Loads

should tumble freely during washing.

Gray whites, dingy colors

• Did you properly sort the load?

Dye transfer can occur when mixing whites and colors in a

load. Sort dark clothes from whites and lights.

• Was the wash temperature too low?

Use hot or warm washes if safe for the load. Make sure your

hot water system is adequate to provide a hot water wash.

Did you use enough detergent, or do you have hard

water?

Use more detergent for washing heavy soils in cold or hard

water.

Cycle too long

Did you choose the Sanitary cycle?

The heater will be activated to provide maximum cleaning

performance. Additional time will be added to the regular

cycle to heat the water. This additional time will depend on

the load size and the hot water inlet temperature.

Is "SUD" shown in the display?

Excessive sudsing has been detected and a suds routine has

been started to destroy excessive suds. This routine will add

time to the original cycle.

Did the load cause imbalance?

When too much imbalance occurs, an imbalance routine will

start to redistribute the load. This routine will add time to your

original cycle.

Door mockedat end of wash cycle

Did all of the water drain out of the washer during the

spin?

Select DRAIN/SPIN to remove any water remaining in the

washer. The washer door will unlock at the end of the drain.

ASSISTANCEORSERVICE

Before calling for assistance or service, please check

"Troubleshooting." It may save you the cost of a service call. If

you still need help, follow the instructions below.

When calling, please know the purchase date and the complete

model and serial number of your appliance. This information will

help us to better respond to your request.

If you need replacement parts

If you need to order replacement parts, we recommend that you

only use FSP®factory specified parts. These parts will fit right

and work right because they are made with the same precision

used to build every new WHIRLPOOL ®appliance.

To locate FSP replacement parts in your area:

In the U.S.A., call the Customer Interaction Center at

1-800-253-1301, or your nearest designated service center.

In Canada, call 1-800-807-6777, or your nearest designated

service center.

Call the Whirlpool Customer Interaction Center toll free:

1-800-253-1301.

Our consultants provide assistance with:

• Features and specifications on our full line of appliances

• Installation information

• Use and maintenance procedures

• Accessory and repair parts sales

• Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.)

• Referrals to local dealers, repair parts distributors, and

service companies

Whirlpool designated service technicians are trained to fulfill the

product warranty and provide after-warranty service anywhere in

the United States.

To locate the Whirlpool designated service company in your area,

you can also look in your telephone directory Yellow Pages.

For further assistance

If you need further assistance, you can write to Whirlpool

Corporation with any questions or concerns at:

Whirlpool Brand Home Appliances

Customer Interaction Center

553 Benson Road

Benton Harbor, M149022-2692

Please include a daytime phone number in your correspondence.

Call the Whirlpool Canada Inc. Customer Interaction Center toll

free:

1-800-481-5681 Monday to Friday 8:00 a.m. - 6:00 p.m. (EST).

Saturday 8:30 a.m. - 4:30 p.m. (EST).

Our consultants provide assistance with:

• Features and specifications on our full line of appliances

• Referrals to local dealers

For service in Canada

Call 1-800-807-6777. Whirlpool Canada Inc. designated service

technicians are trained to fulfill the product warranty and provide

after-warranty service anywhere in Canada.

For further assistance

If you need further assistance, you can write to Whirlpool Canada

Inc. with any questions or concerns at:

Customer Interaction Center

Whirlpool Canada Inc.

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

Please include a daytime phone number in your correspondence.

La page charge ...

Whirlpool GHW9250MQ2 Le manuel du propriétaire

Marque: Whirlpool

Modèle: GHW9250MQ2

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool GHW9250MQ2 Owner's manual

Whirlpool GHW9250MQ2 Le manuel du propriétaire

Ce manuel convient également à

Whirlpool GHW9250MQ2 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents