DeWalt DCCS690H1 Manuel utilisateur

Marque: DeWalt

Modèle: DCCS690H1

Catégorie: Tronçonneuses électriques

Taper: Manuel utilisateur

Ce manuel convient également à

DCCS690 40V Max* Lithium Chainsaw

DCCS690 40V Max* Scie á chaíne de litho

DCCS690 40V Max* Sierra de cadena au lithium-ion

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE

USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-De

English



The definitions below describe the level of severity for each signal

word. Please read the manual and pay attention to these symbols.

DANGER: Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which,

if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if

not avoided, may result in minor or moderate injury.

NOTICE: Indicates a practice not related to personal injury

which, if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR

ANY D

eWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DeWALT

(1-800-433-9258).

WARNING: To reduce the risk of injury, read the instruction manual.



WARNING! Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in

electric shock, fire and/or serious injury.





The term “power tool” in the warnings refers to your mains-operated

(corded) power tool or battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

b) Do not operate power tools in explosive atmospheres, such

as in the presence of flammable liquids, gases or dust.

Power tools create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such

as pipes, radiators, ranges and refrigerators. There is an

increased risk of electric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water

entering a power tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension

cord suitable for outdoor use. Use of a cord suitable for

outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable,

use a ground fault circuit interrupter (GFCI) protected

supply. Use of a GFCI reduces the risk of electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a

power tool while you are tired or under the influence of

drugs, alcohol or medication. A moment of inattention while

operating power tools may result in serious personal injury.

English

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do

not allow persons unfamiliar with the power tool or these

instructions to operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding

of moving parts, breakage of parts and any other condition

that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind and

are easier to control.

g) Use the power tool, accessories and tool bits, etc. in

accordance with these instructions, taking into account

the working conditions and the work to be performed.

Use of the power tool for operations different from those

intended could result in a hazardous situation.

5) BATTERY TOOL USE AND CARE

) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type of battery

pack may create a risk of fire when used with another battery pack.

b) Use power tools only with specifically designated battery

packs. Use of any other battery packs may create a risk of injury

and fire.

c) When battery pack is not in use, keep it away from other

metal objects like paper clips, coins, keys, nails, screws,

or other small metal objects that can make a connection

from one terminal to another. Shorting the battery terminals

together may cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from

the battery, avoid contact. If contact accidentally occurs,

flush with water. If liquid contacts eyes, additionally seek

b) Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in

the off position before connecting to power source and/

or battery pack, picking up or carrying the tool. Carrying

power tools with your finger on the switch or energizing power

tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the

power tool on. A wrench or a key left attached to a rotating

part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewelry or long hair can be caught in

moving parts.

g) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool

for your application. The correct power tool will do the job

better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

English

     The

slender material may catch the saw chain and be whipped toward

you or pull you off balance.





          

Proper handling of the chain saw will reduce the likelihood of

accidental contact with the moving saw chain.

        

 Improperly tensioned or lubricated chain

may either break or increase the chance for kickback.

           

Greasy, oily handles are slippery causing loss of control.

            

         

Use of the

chain saw for operations different than intended could result in a

hazardous situation.



Kickback may occur when the nose or tip of the guide bar touches

an object, or when the wood closes in and pinches the saw chain

in the cut.

Tip contact in some cases may cause a sudden reverse reaction,

kicking the guide bar up and back towards the operator.

Pinching the saw chain along the top of the guide bar may push the

guide bar rapidly back towards the operator.

Either of these reactions may cause you to lose control of the saw

which could result in serious personal injury. Do not rely exclusively

upon the safety devices built into your saw. As a chain saw user,

you should take several steps to keep your cutting jobs free from

accident or injury.

Kickback is the result of tool misuse and/or incorrect operating

procedures or conditions and can be avoided by taking proper

precautions as given below:

         

medical help. Liquid ejected from the battery may cause

irritation or burns.

6) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.





         



A moment of inattention while operating chain saws may cause

entanglement of your clothing or body with the saw chain.

• 

       Holding the

chain saw with a reversed hand configuration increases the risk of

personal injury and should never be done.



          

        Saw

chains contacting a "live" wire may make exposed metal parts of

the power tool "live" and could give the operator an electric shock.





Adequate protective clothing will reduce personal injury by ﬂying

debris or accidental contact with the saw chain.

Operation of a chain saw

while up in a tree may result in personal injury



Slippery

or unstable surfaces such as ladders may cause a loss of balance

or control of the chain saw.



When the tension in the wood ﬁbers is released the spring

loaded limb may strike the operator and/or throw the chain saw

out of control.

English

          



 Kickback forces can be controlled by the operator, if

proper precautions are taken. Do not let go of the chain saw.

           This

helps prevent unintended tip contact and enables better control of the

chain saw in unexpected situations.

         

Incorrect replacement bars and chains may cause

chain breakage and/or kickback.

      

    Decreasing the depth gauge

height can lead to increased kickback.

    



(1.) Grip Saw Firmly. Hold the chain saw firmly with both hands when

the motor is running. Use a firm grip with thumbs and fingers encircling

the chain saw handles. Chain saw will pull forward when cutting on the

bottom edge of the bar, and push backward when cutting along the top

edge of the bar.

(2.) Do not over reach.

(3.) Keep proper footing and balance at all times.

(4.) Don’t let the nose of the guide bar contact a log, branch, ground

or other obstruction.

(5.) Don’t cut above shoulder height.

(6.) Use devices such as low kickback chain and reduced kickback

guide bars that reduce the risks associated with kickback.

(7.) Only use replacement bars and chains specified by the

manufacturer or the equivalent.

(8.) Never let the moving chain contact any object at the tip of the

guide bar.

(9.) Keep the working area free from obstructions such as other

trees, branches, rocks, fences, stumps, etc. Eliminate or avoid

any obstruction that your saw chain could hit while you are cutting

through a particular log or branch.

(10.) Keep your saw chain sharp and properly tensioned. A loose or

dull chain can increase the chance of kickback. Check tension at

regular intervals with the motor stopped and tool unplugged, never

with the motor running.

(11.) Begin and continue cutting only with the chain moving at full

speed. If the chain is moving at a slower speed, there is a greater

chance for kickback to occur.

(12.) Cut one log at a time.

(13.) Use extreme caution when re-entering a previous cut. Engage

ribbed bumpers into wood and allow chain to reach full speed before

proceeding with cut.

(14.) Do not attempt plunge cuts or bore cuts.

(15.) Watch for shifting logs or other forces that could close a cut and pinch

or fall into chain.



WARNING: The following features are included on your saw

to help reduce the hazard of kickback; however such features will not

totally eliminate this dangerous reaction. As a chain saw user do not

rely only on safety devices. You must follow all safety precautions,

instructions, and maintenance in this manual to help avoid kickback

and other forces which can result in serious injury.

•    designed with a small radius

tip which reduces the size of the kickback danger zone on bar

tip. A reduced - kickback guide bar is one which has been

demonstrated to significantly reduce the number and seriousness

of kickbacks when tested in accordance with safety requirements

for electric chain saws.

• , designed with a contoured depth gauge

and guard link which deflect kickback force and allow wood to

gradually ride into the cutter. A low-kickback chain is a chain

which has met kickback performance requirements of ANSI

B175.1-2012.

• 



• 

        

English

 Contact with a “live” wire will make exposed metal parts

of the tool “live” and shock the operator.

•        

 Read thoroughly and understand completely all

instructions in this manual.

•      make sure saw chain is not

contacting any object.

• 



 A chain saw is intended for two-handed use

only.

• 

• 



• 

• 

•         

 because slender material may catch the saw chain and

be whipped toward you or pull you off balance.

WARNING: Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities contains chemicals

known to the State of California to cause cancer, birth defects or

other reproductive harm. Some examples of these chemicals are:

•leadfromlead-basedpaints,

•  

crystalline silica from bricks and cement and other masonry

products, and

•arsenicandchromiumfromchemically-treatedlumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to

filter out microscopic particles.

•        



       

Allowing dust to get into your mouth, eyes, or

lay on the skin may promote absorption of harmful chemicals.

WARNING:



 Always use NIOSH/OSHA approved

respiratory protection appropriate for the dust exposure. Direct

particles away from face and body.



 The process of cross cutting a felled tree or log into lengths.

 A device used to stop the saw chain when the

trigger is released.

   - A chain saw without the saw chain

and guide bar.

  The toothed part that drives the

saw chain.



 The process of cutting down a tree.

  The final cut in a tree felling operation made on

the opposite side of the tree from the notching cut.

  The support handle located at or toward the front of

the chain saw.

     A structural barrier between the front

handle of a chain saw and the guide bar, typically located close

to the hand position on the front handle.

  A solid railed structure that supports and guides the

saw chain.

     Enclosure fitted over guide bar to

prevent tooth contact when saw is not in use.

   The backward or upward motion, or both of the

guide bar occurring when the saw chain near the nose of the

top area of the guide bar contacts any object such as a log or

branch, or when the wood closes in and pinches the saw chain

in the cut.



 The rapid pushback of the saw which can occur

when the wood closes in and pinches the moving saw chain in the

cut along the top of the guide bar.

    The rapid upward and backward

English

motion of the saw which can occur when the moving saw chain

near the upper portion of the tip of the guide bar contacts an

object, such as a log or branch.

 Removing the branches from a fallen tree

  A chain that complies with the kickback

performance requirements of ANSI B175.1-2012 (when tested

on a representative sample of chain saws.)

     Those positions assumed in

performing the bucking and felling cuts.

    A notch cut in a tree that directs the

tree’s fall.

 Rear Handle - The support handle located at or toward the rear

of the saw.

  A guide bar which has been

demonstrated to reduce kickback significantly.

     A chain that complies with

kickback performance requirements of ANSI B175.1-2000 when

tested with specific chain saws. It may not meet the

ANSI performance

requirements when used with other saws.

 Saw Chain - A loop of chain having cutting teeth, that cut the

wood,and that is driven by the motor and is supported by the

guide bar.

  The ribs used when felling or bucking to pivot

the saw and maintain position while sawing.

 Switch - A device that when operated will complete or interrupt

an electrical power circuit to the motor of the chain saw.

    The mechanism that transmits motion from a

trigger to the switch.

    A movable stop that prevents the

unintentional operation of the switch until manually actuated.



Your DeWALT DCCS690 Chainsaw is ideal for pruning applications

and cutting logs up to 14" inches (355 mm) in diameter.

• The label on your tool may include the following symbols. The

symbols and their definitions are as follows:

V ...................volts

A ...................amperes

Hz ................. hertz

W ..................watts

min ............... minutes

or AC ....... alternating

current

or DC ... direct current

................. Class I

Construction

(grounded)

o ................. no load speed

................. Class

II Construction

(double

insulated)

…/min .......... per minute

RPM ............. revolutions per

minute

................. earthing terminal

.................. safety alert

symbol

CSPM ........... cut strokes per

minute

................. Read instruction

manual before use

................. Use proper

respiratory

protection

................. Use proper

hearing protection

.................. Use proper eye

protection

................ Rotational

direction of the

saw chain

................. Contact of the

guide bar tip

with any object

should be avoided

................. Tip contact can

cause the guide

bar to move

suddenly upward

and backward,

which can cause

serious injury

............. Always use two

hands when

operating the

chainsaw







English

When ordering replacement battery packs, be sure to include the

catalog number and voltage. Consult the chart at the end of this

manual for compatibility of chargers and battery packs.

The battery pack is not fully charged out of the carton. Before using

the battery pack and charger, read the safety instructions below and

then follow charging procedures outlined.



• Do not charge or use the battery pack in explosive

atmospheres, such as in the presence of flammable liquids,

gases or dust. Inserting or removing the battery pack from the

charger may ignite the dust or fumes.

• NEVER force the battery pack into the charger. DO NOT

modify the battery pack in any way to fit into a non-

compatible charger as battery pack may rupture causing

serious personal injury. Consult the chart at the end of this

manual for compatibility of batteries and chargers.

• Charge the battery packs only in designated D

eWALT chargers.

• DO NOT splash or immerse in water or other liquids. If appliance

does get wet, allow to dry for a minimum of 48 hours before using.

• Do not store or use the tool and batterypack in locations

where the temperature may reach or exceed 105°F (40°C)

(such as outside sheds or metal buildings in summer). For

best life store battery packs in a cool, dry location.

NOTE: Do not store the battery packs in a tool with the

trigger switch locked on. Never tape the trigger switch in the

ON position.

WARNING: Fire hazard. Never attempt to open the

battery pack for any reason. If the battery pack case is cracked or

damaged, do not insert into the charger. Do not crush, drop or damage

the battery pack. Do not use a battery pack or charger that has

received a sharp blow, been dropped, run over or damaged in any way

(e.g., pierced with a nail, hit with a hammer, stepped on). Damaged

battery packs should be returned to the service center for recycling.

WARNING: Fire hazard. Do not store or carry

the battery pack so that metal objects can contact exposed

battery terminals. For example, do not place the battery pack in

aprons, pockets, tool boxes, product kit boxes, drawers, etc., with

loose nails, screws, keys, etc. Transporting batteries can possibly

cause fires if the battery terminals inadvertently come in

contact with conductive materials such as keys, coins, hand

tools and the like. The US Department of Transportation Hazardous

Material Regulations (HMR) actually prohibit transporting batteries in

commerce or on airplanes (e.g., packed in suitcases and carry-on

luggage) UNLESS they are properly protected from short circuits. So

when transporting individual battery packs, make sure that the battery

terminals are protected and well insulated from materials that could

contact them and cause a short circuit.



Your DeWALT batteries comply with all applicable shipping

regulations as prescribed by industry and legal standards, including

UN Recommendations on the Transport of Dangerous Goods;

International Air Transport Association (IATA) Dangerous Goods

Regulations, International Maritime Dangerous Goods (IMDG)

Regulations, and U.S. Department of Transportation Regulations.

Lithium-ion cells and batteries have been tested to section 38.3 of the

UN Recommendations on the Transport of Dangerous Goods Manual

of Tests and Criteria.

The shipping or transportation of the battery in this product is restricted

and may be classified as a Class 9 Hazardous material.

English

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li-Ion)

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when

lithium ion battery packs are burned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If battery

liquid gets into the eye, rinse water over the open eye for 15

minutes or until irritation ceases. If medical attention is needed,

the battery electrolyte is composed of a mixture of liquid organic

carbonates and lithium salts.

• Contents of opened battery cells may cause respiratory irritation.

Provide fresh air. If symptoms persist, seek medical attention.

WARNING: Burn hazard. Battery liquid may be

flammable if exposed to spark or flame.



The RBRC™ (Rechargeable Battery Recycling

Corp oration) Seal on the nickel cadmium, nickel metal

hydride or lithium ion batteries (or battery packs) indicate

that the costs to recycle these batteries (or battery packs)

at the end of their useful life have already been paid by

eWALT. In some areas, it is illegal to place spent nickel

cadmium, nickel metal hydride or lithium ion batteries in the trash or

municipal solid waste stream and the RBRC program provides an

environmentally conscious alternative.

RBRC™, in cooperation with DeWALT and other battery users, has

established programs in the United States and Canada to facilitate

the collection of spent nickel cadmium, nickel metal hydride or lithium

ion batteries. Help protect our environment and conserve natural

resources by returning the spent nickel cadmium, nickel metal hydride

or lithium ion batteries to an authorized D

eWALT service center or

SHIPPING BY AIRPLANE (BY AIR) OR SHIP (BY SEA)

 • Contactyourcarrierforuptodateinstructions.Haveyourcontents

(including the battery) with you when contacting them. The

specifications written on them will be needed to prepare them for

shipment, pack them in a compliant box, and properly label the box.

SHIPPING BY GROUND (HIGHWAY OR RAIL)

 • Theoriginalproductboxanditspackingmaterialcanbeusedforshippingby

ground within the United States and Canada with the following stipulations:

1. The battery and all other contents must be in their original packing materials

and arranged as received (including the battery in its original plastic bag and

battery box).

2. The original product box and all other packing materials must be undamaged.

3. The shipment must be include a document which contains the following:

   • Thepackagecontainslithium-ioncellsorbatteries.

   • The package must be handled with care and that a

flammability hazard exists if the package is damaged.

   • Special procedures should be followed in the event the

package is damaged, to include inspection and repacking if

necessary.

   • The telephone numbers for additional information (US and

Canada 1-888-698-2571, Elsewhere +1-410-329-9200).

   • Toshipbygroundinagenericbox,contactyourcarrierfor

up to date instructions. Have your contents (including the

battery) with you when contacting them. The specifications

written on them will be needed to prepare them for shipment,

pack them in a compliant box, and properly label the box.

It is forbidden to fly with these batteries even if the batteries are in

checked baggage.

The information provided in this section of the manual is provided in

good faith and believed to be accurate at the time the document was

created. However, no warranty, expressed or implied, is given. The

shipper is responsible to comply with the applicable regulations.

English

• Do not expose the charger to rain or snow.

• Pull by the plug rather than the cord when disconnecting the

charger. This will reduce the risk of damage to the electric plug and cord.

• Make sure that the cord is located so that it will not be

stepped on, tripped over or otherwise subjected to damage

or stress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk of

fire, electric shock or electrocution.

• When operating a charger outdoors, always provide a dry

location and use an extension cord suitable for outdoor use. Use

of a cord suitable for outdoor use reduces the risk of electric shock.

• An extension cord must have adequate wire size (AWG or

American Wire Gauge) for safety. The smaller the gauge number

of the wire, the greater the capacity of the cable, that is, 16 gauge

has more capacity than 18 gauge. An undersized cord will cause a

drop in line voltage resulting in loss of power and overheating. When

using more than one extension to make up the total length, be sure

each individual extension contains at least the minimum wire size.

The following table shows the correct size to use depending on cord

length and nameplate ampere rating. If in doubt, use the next heavier

gauge. The lower the gauge number, the heavier the cord.





Volts 

120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Than

Not More

Than

AWG

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

to your local retailer for recycling. You may also contact your local

recycling center for information on where to drop off the spent battery.

RBRC™ is a registered trademark of the Rechargeable Battery

Recycling Corporation.





SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instructions for battery chargers.

• Before using the charger, read all instructions and cautionary markings

on the charger, battery pack and product using the battery pack.

WARNING: Shock hazard. Do not allow any liquid to

get inside the charger. Electric shock may result.

CAUTION: Burn hazard. To reduce the risk of injury,

charge only D

eWALT rechargeable battery packs. Other types of

batteries may overheat and burst resulting in personal injury and

property damage.

NOTICE: Under certain conditions, with the charger plugged into the

power supply, the charger can be shorted by foreign material. Foreign

materials of a conductive nature, such as, but not limited to, grinding

dust, metal chips, steel wool, aluminum foil or any buildup of metallic

particles should be kept away from the charger cavities. Always unplug

the charger from the power supply when there is no battery pack in the

cavity. Unplug the charger before attempting to clean.

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger and

battery pack are specifically designed to work together.

• These chargers are not intended for any uses other than

charging D

eWALT rechargeable batteries. Any other uses may

result in risk of fire, electric shock or electrocution.

English

2. Insert the battery pack (N) into the charger, as shown in

 , making sure the pack is fully seated

in charger. The red (charging) light will blink continuously, indicating

that the charging process has started.

3. The completion of charge will be indicated by the red light

remaining ON continuously. The pack is fully charged and may be

used at this time or left in the charger.



PACK CHARGING

PACK CHARGED

HOT/COLD DELAY

PROBLEM PACK OR CHARGER

PROBLEM POWERLINE



This charger is designed to detect certain problems that can arise.

Problems are indicated by the red light flashing at a fast rate. If this

occurs, remove and then reinsert the battery pack into the charger.

If the problem persists, try a different battery pack to determine if the

charger is working properly. If the new pack charges correctly, then the

original pack is defective and should be returned to a service center

or other collection site for recycling. If the new battery pack elicits the

same trouble indication as the original, have the charger and the battery

pack tested at an authorized service center.



This charger has a hot/cold delay feature: when the charger detects a

battery that is hot, it automatically starts a delay, suspending charging

until the battery has cooled. After the battery has cooled, the charger

• Do not place any object on top of the charger or place the

charger on a soft surface that might block the ventilation

slots and result in excessive internal heat. Place the charger

in a position away from any heat source. The charger is ventilated

through slots in the top and the bottom of the housing.

• Do not operate the charger with a damaged cord or plug.

• Do not operate the charger if it has received a sharp blow,

been dropped or otherwise damaged in any way. Take it to an

authorized service center.

• Do not disassemble the charger; take it to an authorized

service center when service or repair is required. Incorrect

reassembly may result in a risk of electric shock, electrocution or fire.

• Disconnect the charger from the outlet before attempting

any cleaning. This will reduce the risk of electric shock.

Removing the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

• The charger is designed to operate on standard 120V

household electrical power. Do not attempt to use it on any

other voltage.



Your tool uses a DeWALT charger.

Be sure to read all safety instructions

before using your charger. Consult the

chart at the end of this manual for

compatibility of chargers and battery

packs.





1. Plug the charger into an appropriate

outlet before inserting the battery

pack.

FIG. 1

English

b. Check to see if receptacle is connected to a light switch which turns

power off when you turn out the lights;

c. Move the charger and battery pack to a location where the surrounding

air temperature is approximately 65°F – 75°F (18° – 24°C);

d. If charging problems persist, take the tool, battery pack and

charger to your local service center.

5. The battery pack should be recharged when it fails to produce

sufficient power on jobs which were easily done previously. DO

NOT CONTINUE to use under these conditions. Follow the

charging procedure. You may also charge a partially used pack

whenever you desire with no adverse effect on the battery pack.

6. Foreign materials of a conductive nature such as, but not limited

to, grinding dust, metal chips, steel wool, aluminum foil, or any

buildup of metallic particles should be kept away from charger

cavities. Always unplug the charger from the power supply when

there is no battery pack in the cavity. Unplug the charger before

attempting to clean.

7. Do not freeze or immerse the charger in water or any other liquid.

WARNING: Shock hazard. Don’t allow any liquid to

get inside the charger. Electric shock may result.

WARNING: Burn hazard. Do not submerge the

battery pack in any liquid or allow any liquid to enter the battery pack.

Never attempt to open the battery pack for any reason. If the plastic

housing of the battery pack breaks or cracks, return to a service center

for recycling.



1. The best storage place is one that is cool and dry, away from direct

sunlight and excess heat or cold.

automatically switches to the pack charging mode. This feature

ensures maximum battery life. The red light flashes long, then short

while in the hot/cold delay mode.

LEAVING THE BATTERY PACK IN THE CHARGER

The charger and battery pack can be left connected with the charge

indicator showing Pack Charged.

WEAK BATTERY PACKS: Weak batteries will continue to function

but should not be expected to perform as much work.

FAULTY BATTERY PACKS: This charger will not charge a faulty

battery pack. The charger will indicate faulty battery pack by refusing

to light or by displaying problem pack or charger.

NOTE: This could also mean a problem with a charger.



1. Longest life and best performance can be obtained if the battery

pack is charged when the air temperature is between 65 °F and

75 °F (18 ° – 24 °C). DO NOT charge the battery pack in an air

temperature below +40°F (+4.5°C), or above +105°F (+40.5°C).

This is important and will prevent serious damage to the battery pack.

2. The charger and battery pack may become warm to the touch

while charging. This is a normal condition, and does not indicate

a problem. To facilitate the cooling of the battery pack after use,

avoid placing the charger or battery pack in a warm environment

such as in a metal shed or an uninsulated trailer.

3. A cold battery pack will charge at about half the rate of a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery pack warms.

4. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp or other appliance;

English







WARNING: Before removing or installing battery,

make

certain the lock-off lever is engaged

to prevent switch actuation.

 Insert battery pack (N) into battery housing

(Q) as shown in  until fully seated and an audible click is heard.

Make sure battery pack is fully seated and fully latched into position.

FIG. 3

FIG. 4

: Depress the battery release button (O) in

the back of the battery housing and pull battery pack out of tool as

shown in



Some D

eWALT battery packs include a fuel gauge which consists of

three green LED lights that indicate the level of charge remaining in

the battery pack.

To actuate the fuel gauge, press and hold the fuel gauge button (5A).

A combination of the three green LED lights will illuminate designating

2. For long storage, it is recommended to store a fully charged battery

pack in a cool dry place out of the charger for optimal results.

NOTE: Battery packs should not be stored completely depleted of

charge. The battery pack will need to be recharged before use.





A. Variable speed trigger switch I. Oil level indicator

B. Lock-off lever J. Guide bar scabbard

C. Chain brake / front hand guard K. Rear handle

D. Guide bar L. Front handle

E. Saw chain M. Battery housing

F. Sprocket cover N. Battery Pack

G. Bar adjust locking knob O. Battery release button

H. Chain tensioning knob P. Oil cap (not shown)

FIG. 2

English

•

Flip up locking lever and rotate the bar adjust locking knob (G)

counterclockwise as shown into remove sprocket cover (F).

• Wearingprotectivegloves, graspthe sawchain(E) andwrapit

around the guide bar (D), ensuring the teeth are facing the correct

direction (see )

•

Ensure the chain is properly set in the slot around the entire guide bar.

• Place the saw chain around the sprocket (7A). While lining up the

slot on the guide bar

with chain tensioning pin

(7B) and the bolt (7C) on

the base of the tool as

shown in .

•

Once in place, hold

the bar still, replace

sprocket cover (F).

Make sure tool-free

tension assembly bolt

hole on the cover lines

up with the bolt (7B)

in the main housing.

Flip up locking lever

and r

otate the bar

adjust locking knob (G)

clockwise until it clicks,

then loosen knob one

ull turn, so that the

saw chain can be

properly tensioned.

• Rotate the chain

tensioning knob (H)

clockwise to increase

tension as shown in

. Make sure the saw chain (E) is snug around the guide

bar (D). Tighten the bar adjust locking knob until it clicks. The bar is

secure after three audible clicks are heard. Further tightening is not

required.

the level of charge left. When the level of

FIG. 5

charge in the battery is below the

usable limit, the fuel gauge will not

illuminate and the battery will need to

be recharged.

NOTE: The fuel gauge is only an

indication of the charge left on the

battery pack. It does not indicate tool

functionality and is subject to variation

based on product components, temperature and end-user application.

For more information regarding fuel gauge battery packs, please call

1-800-4-D

eWALT (1-800-433-9258) or visit our website www.dewalt.com.





CAUTION:

The chain is sharp and can cut

you when it is not running.

WARNING:



 Failure to do

this could result in serious

personal injury.

The saw chain (E) and

guide bar (D) are packed

separately in the carton.

The chain has to be

attached to the bar, and

both must be attached to

the body of the tool.

• Placethesawonaflat,

firm surface.

FIG. 6

FIG. 8

FIG. 7

English



CAUTION:

The chain is sharp and can cut

you when it is not running.

WARNING:





Failure to do this could

result in serious personal injury

• Flip up locking tab and rotate the bar adjust locking knob (G)

counte

rclockwise to release chain tension.

• Removesprocketcover(F)asdescribedin“InstallingtheGuide

Bar and Saw Chain” section.

• Liftthewornsawchain(E)outofthegrooveintheguidebar(D).

• Place the new chain

in the slot of the guide

bar, making sure the

saw teeth are facing

the correct direction

by matching the arrow

on the chain with the

graphic on the sprocket

cover (F) shown in

.

• Follow instructions for

“Installing the Guide

Bar and Saw Chain.”

Replacement chain and bar are available from your nearest DeWALT

service center.

• DCCS690requiresreplacementchain#DWRC1600,servicepart

number 90618541. Replacement 16” bar, service part number

90618542.



CAUTION:

The chain is sharp and can cut

you when it is not running.

WARNING:



Failure to do this could

result in serious personal injury

• Withthesawonaflat,firmsurface,checkthesawchain(E)tension.The

tension is correct when the chain snaps back after being pulled 1/8 inch

(3mm) away from the guide bar (D) with light force from the index finger

and thumb as shown in . There should be no “sag” between the

guide bar and the chain on the underside as shown in .

• To adjust saw chain tension,

flip up locking tab and rotate the

bar

adjust locking knob (G) counterclockwise one full turn.

Rotate

the chain tensioning knob (H) clockwise until the chain tension is

correct as instructed above.

• Donotover-tensionthechainasthiswillleadtoexcessivewear

and will reduce the life of the bar and chain.

• Oncechaintensioniscorrect,securelytightenbaradjustlockingknob.

NOTE: The bar

adjust locking knob has a detent tightening system.

The

sprocket cover is secure after three audible clicks are heard.

Further tigtening is not required.

•

When the chain is new, check the tension frequently (after removing

battery) during the first 2 hours of use as a new chain stretches slightly.

FIG. 9 FIG. 10

FIG. 11

English



• Alwaysremovethebatteryfromthetoolandcovertheguidebar

(D) with the scabbard (J)  when transporting the saw.

• Engagechainbrakebypushingchain brake / front hand guard (C) forward.



WARNING: Read and understand all

 Failure to follow all instructions listed below may result

in electric shock, fire and/or serious personal injury.

• 

or death. See  “Guard Against

Kickback”, to avoid the risk of kickback.

•          

 Keep feet apart. Divide your weight

evenly on both feet.

• 

so that your body

is to the left of the guide bar.

•           

 Keep elbow of left arm locked so that left arm is straight to

withstand a kickback.

WARNING: (left

hand on the rear handle and right hand on the front handle).

WARNING:    

to be in line with the guide bar (D) when operating the chain saw.

• 





This chain saw is equipped with an auto oiling system that keeps the

saw chain and guide bar constantly lubricated. The oil level indicator

(I) shows the level of the oil in the chain saw. If the oil level is less than

a quarter full, remove the battery from the chain saw and refill with

the correct type of oil.

Always empty oil tank when finished cutting.

NOTE: Use a high quality bar and chain oil for proper chain and

bar lubrication. As a temporary substitute, a non-detergent SAE30

weight motor oil can be used. The use of a vegetable based bar

and chain oil is recommended when pruning trees. Mineral oil is not

recommended because it may harm trees. Never use waste oil or

very

thick oil. These may damage your chain saw.



• Flip down locking lever and

unscrew counterclockwise a

quarter turn and then remove

the oil cap (P). Fill the reservoir

with the recommended bar and

chain oil until the oil level has

reached the top of the oil level

indicator (I).

• Refit the oil cap and tighten

clockwise a quarter turn. Flip

up locking lever to its locked

position.

• Periodically switch the chain saw off and check the oil level

indicator to ensure the bar and chain are being properly oiled.

FIG. 13

FIG. 12

English

• Removethebatteryfromthetool.

• Toengagethechainbrake,push the

chain brake / front hand guard (C)

forward until it clicks into place.

• Pull the chain brake / front hand

guard (C) towards the front handle

(L) into the “set” position as shown

in .

• Thetoolisnowreadytouse.

NOTE: In the event of kickback, your

left hand will come in contact with the front guard, pushing it

forward, toward the workpiece. This will stop the tool.



Test the chain brake before every use to make sure it operates correctly.

• Placethetoolonaflat,firmsurface.Makesurethesawchain(5)is

clear of the ground.

• Gripthetoolfirmlywithbothhandsandturnthechainsawon.

• Rotate your left handforward around the front handle(L) so the

back of your hand comes in contact with the Chain brake / front

hand guard (C) and push it forward, toward the workpiece. The

saw chain should stop immediately.

NOTE: If saw does not stop immediately, stop use of tool and bring it

to a DeWalt service center nearest you.

WARNING:

Make sure to set chain brake before cutting.





The process of cutting down a tree. Be sure battery is fully charged

before felling a tree so you can finish on a single charge. Do not fell

trees in high wind conditions.

WARNING: Felling can result in injury. It should only

be performed by a trained person.

• A retreat path should be planned and cleared as necessary

before cuts are started. The retreat path should extend back and

You may lose control

of saw causing severe injury.

•           



•  Exert only light pressure. Do

not put pressure on chain saw at end of cut.

WARNING: When not in use always have the

chain brake engaged and battery removed.





      



This tool is equipped with a variable

speed trigger switch. To turn the unit

on, ensure chain brake is not engaged.

Push down on the the lock off lever

(B), shown in , and squeeze

the trigger switch (A). Once the unit

is running, you may release the lock

off lever. The farther you depress the

trigger, the faster it will operate.

In order to keep the unit running you must continue to squeeze the

trigger. To turn the unit off, release the trigger.

NOTE: If too much force is applied while making a cut the saw will

turn off. To restart saw, you must release the lock off lever (b) and the

trigger switch (A) before the saw will restart. Begin your cut again this

time with less force. Allow the saw to cut at its own pace.

WARNING: Never attempt to lock a switch in the

ON position.



Your chain saw is equipped with a motor chain braking system which

will stop the chain quickly in case of kickback.

FIG. 15

FIG. 14

English

diagonally to the rear of

the expected line of fall.

()

• Before felling is started,

consider the natural

lean of the tree, the

location of larger

branches and the wind

direction to judge which

way the tree will fall.

Have wedges (wood,

plastic or aluminum)

and a heavy mallet handy. Remove dirt, stones, loose bark, nails,

staples, and wire from the tree where the felling cuts are to be

made.

• Notching Undercut - Make the notch 1/3 of the diameter of the

tree, perpendicular to the direction of the fall. Make the lower

horizontal notching cut first. This will help to avoid pinching of

either the saw chain or the guide bar when the second notch cut

is being made ().

• Felling Back Cut - Make the felling back cut at least 2 inches

(51mm) higher than the horizontal notching cut. Keep the felling

back cut parallel to the horizontal notching cut. Make the felling

back cut so enough wood is left to act as a hinge. The hinge wood

keeps the tree from twisting and falling in the wrong direction.

Do not cut through the

hinge ().

• As the felling cut gets

close to the hinge the

tree should begin to fall.

If there is any chance

that the tree may not fall

in the desired direction

or it may rock back and

bind the saw chain, stop

cutting before the felling

cut is complete and use wedges to open the cut and drop the

tree along the desired line of fall. When the tree begins to fall

remove the chain saw from the cut, stop the motor, put the

chain saw down, then use the retreat path planned. Be alert for

overhead limbs falling and watch your footing ().

LIMBING

Removing the branches

from a fallen tree. When

limbing, leave larger lower

limbs to support the log

off the ground. Remove

the small limbs in one cut.

Branches under tension

should be cut from the

bottom of the branch

towards the top to avoid

binding the chain saw as

shown in . Trim limbs from opposite side keeping tree stem

between you and saw. Never make cuts with saw between your legs

or straddle the limb to be cut.



WARNING:  



Cutting a felled tree or

log into lengths. How you

should cut depends on

how the log is supported.

Use a saw horse

( ) whenever

possible.

FIG. 18

FIG. 19

DIRECTION

FALL

RETREAT

45°

TREE

FIG. 16

2 (5cm)

INCHES

DIRECTION

OF FALL

2 (5cm)

INCHES

HINGE

NOTCH

FELLING BACK

CUT

FIG. 17

English

Always start a cut with

the chain running at full

speed.

• Placethebottomspike

(R) of the chain saw

behind the area of the

initial cut as shown in

.

• Turnthechain sawon

then rotate the chain

and bar down into the

tree, using the spike as a hinge.

• Oncethechainsawgetstoa45degreeangle,levelthechainsaw

again and repeat steps until you cut fully through.

• make a

cut from the top (overbuck), but avoid cutting the earth as this will

dull your saw quickly.

•   



First, cut 1/3 the

diameter from the

underside (underbuck).

Then make the finishing

cut by overbucking to

meet the first cut.

•   When

  

ends

First, cut 1/3

down from the

top overbuck.

Then make the

finished cut by

underbucking

the lower 2/3 to

meet the first cut.

•  always stand on the uphill side of the log. When

“cutting through”, to maintain complete control reduce the cutting

pressure near the end of the cut without relaxing your grip on the

chain saw handles. Don’t let the chain contact the ground. After

completing the cut, wait for the saw chain to stop before you move

the chain saw. Always stop the motor before moving from cut to cut.



Use only mild soap and damp cloth to clean the tool. Do not use

solvents to clean the plastic housing of the saw. Never let any liquid

get inside the tool; never immerse any part of the tool into a liquid.

IMPORTANT: To assure product SAFETY and RELIABILITY,

repairs, maintenance and adjustment should be performed

by a DeWALT authorized service center, always using identical

replacement parts.

Regular maintenance ensures a long effective life for your chain saw.



After every few hours of use, remove the sprocket cover, guide bar

and chain and clean thoroughly using a soft bristle brush. Ensure oiling

hole on bar is clear of debris. When replacing dull chains with sharp

chains it is good practice to flip the chain bar from bottom to top.



CAUTION: 

The chain is sharp and can cut

you when it is not running.

WARNING:



 Failure to do

this could result in serious personal injury.

NOTE: The cutters will dull immediately if they touch the ground or

a nail while cutting.

CUT FROM TOP

(OVERBUCK)

AVOID CUTTING EARTH

FIG. 20

2nd CUT OVERBUCK

(2/3DIAMETER)

TO MEET 1st CUT

(TO AVOID PINCHING)

1st CUT UNDERBUCK

(1/3 DIAMETER)

AVOID SPLINTERING

FIG. 21

2nd CUT UNDERBUCK

(2/3 DIAMETER)

TO MEET 1st CUT

(TO AVOID PINCHING)

1st CUT OVERBUCK

(1/3 DIAMETER)

TO AVOID SPLINTERING

FIG. 22

La page charge ...

DeWalt DCCS690H1 Manuel utilisateur

Marque: DeWalt

Modèle: DCCS690H1

Catégorie: Tronçonneuses électriques

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt DCCS690H1 User manual
español: DeWalt DCCS690H1 Manual de usuario

DeWalt DCCS690H1 Manuel utilisateur

Ce manuel convient également à

DeWalt DCCS690H1 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents