United States Stove TR007 Le manuel du propriétaire

Marque: United States Stove

Modèle: TR007

Catégorie: Poêles

Taper: Le manuel du propriétaire

PONDEROSA HIGH-EFFICIENCY WOODSTOVE

Owner’s Manual

Model TR007

EPA Certied (3.20 grams/Hr.)

(Save these Instructions)

READ ALL INSTRUCTIONS CAREFULLY BEFORE

INSTALLING OR OPERATING THIS STOVE. FAILURE TO

FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTY

DAMAGE, BODILY INJURY, OR EVEN DEATH.

This stove meets test standards:

US: Ul1482-2011 & CDN: ULC-S627-00

REFER TO MARKINGS ON STOVE LABELS FOR

ADDITIONAL INFORMATION.

SAFETY NOTICE: IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE/BUILDING FIRE MAY RESULT. FOR YOUR

SAFETY, CONTACT LOCAL OR MUNICIPAL BUILDING OR FIRE OFFICIALS ABOUT PERMITS, RESTRICTIONS AND

INSTALLATION REQUIREMENTS FOR YOUR AREA.

NOTE: IT IS RECOMMENDED INSTALLATION BE

COMPLETED BY A QUALIFIED HEATING EQUIPMENT

INSTALLER!

ROOM HEATER, SOLID FUEL TYPE, ALSO FOR USE IN

MOBILE (USA ONLY)

U.S. Environmental Protection Agency

Certied to comply with 2015 particulate emissions

standards.

852201D-2001G

U.S. Stove Company

227 Industrial Park Road,

South Pittsburg, TN 37380

Phone 1-800-750- 2723

www.usstove.com

Le Manuel de langue francais est disponible a www.

usstove.com / French language manual is available at

www.usstove.com

-2-

This manual describes the installation and operation of the Vogelzang, TR007 wood heater. This heater meets the

2015 U.S. Environmental Protection Agency’s crib wood emission limits for wood heaters sold after May 15, 2015.

Under specic test conditions this heater has been shown to deliver heat at rates ranging from 11,913 to 34,108

Btu/hr.

Note: The BTU ratings mentioned above are based on the EPA test protocol burning dimensional Douglas Fir

lumber. Our advertised BTU’s are based on the rst hour of operation at high burn rate burning cordwood.

SAFETY INSTRUCTIONS-READ ALL INSTRUCTIONS CAREFULLY

1. The installation of this stove must comply with your local building code rulings. Please observe the clearances

to combustibles (see gures 5–7). Do not place fuel, furniture or any other objects within the clearance area.

2. Verify that the stove is properly assembled and installed before ring the stove for the rst time. After reading

these instructions, if you have any doubt about your ability to complete your installation properly, you must

obtain the services of a professional licensed installer familiar with all aspects of safe and correct installation.

DO NOT use temporary or makeshift compromises during installation. There must be NO DEVIATION OR

ALTERATION OF ANY KIND from the very specic instructions spelled out in this instruction manual as it pertains

to the installation of this woodstove. NO EXCEPTIONS!

3. DO NOT store wood, kindling, ammable liquids or other combustible materials in the vicinity of the appliance.

Refer to certication label on back of unit and reference gures 5–7 in this manual.

4. FOR MOBILE HOME INSTALLATIONS IN U.S.A. ONLY. DO NOT INSTALL THIS STOVE IN A MOBILE HOME,

MANUFACTURED HOME, TRAILER OR TENT NO EXCEPTIONS! (HUD Federal Standard: 24 CFR Ch.XX).

5. DO NOT ELEVATE THIS STOVE BY ANY MEANS. (i.e. bricks under legs, cement blocks) Stove legs must set

directly upon the solid-surface non-combustible oor as specied in this stove instruction manual.

6. DO NOT MODIFY THIS STOVE IN ANY WAY! Stove must be installed with legs and heat shield provided, attached

as shown in the instructions. DO NOT OPERATE WITHOUT BOTTOM HEAT SHIELD IN PLACE – NO EXCEPTIONS.

Assemble only with original parts as supplied and shown in this manual. DO NOT OPERATE A STOVE THAT

IS MISSING ANY PARTS! If any parts are missing or defective, please notify the dealer or manufacturer

immediately. Replace missing, broken or worn parts with factory original or equivalent parts only.

7. CAUTION: DO NOT ALTER COMBUSTION AIR CONTROL RANGE TO INCREASE FIRING OR FOR ANY REASON.

Altering or tampering with air control beyond normal capacity will create unsafe and hazardous conditions.

8. Always connect this stove to a chimney and vent to the outside. Never vent to a room or inside a building.

DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

9. DO NOT CONNECT A WOOD BURNING STOVE TO AN ALUMINUM TYPE B GAS VENT. This is not safe. Use code-

approved masonry chimney with ue liner or an Underwriters Laboratories Listed UL 103 HT (US)/ULC-S629

(CDN) Residential Type and Building Heating Appliance Chimney system. Use a 6˝/152mm diameter chimney,

that is high enough to give a good draft. (See specics in Chimney Connections instructions).

10. Be sure that your chimney is safely constructed and in good repair. Have the chimney inspected by the re

department or a qualied inspector. Your insurance company should be able to recommend a qualied

inspector. Chimney connector pipe must be in good condition. Replace if necessary before using stove.

11. Creosote or soot may build up in the chimney connector and chimney and cause a house/building

re. Inspect the chimney connector and chimney twice monthly during the heating season and clean if

necessary. (see Service Hints).

12. In the event of a chimney re, turn the air controls to closed positions, leave the building and CALL THE FIRE

DEPARTMENT IMMEDIATELY! Have a clearly understood plan on how to handle a chimney re by contacting

your local re authority for information on proper procedures in the event of a chimney re. After the re is

out, the chimney must be cleaned and inspected for any stress or cracks before starting another re. Check

the condition of any combustibles surrounding the chimney.

13. Ashes should not be allowed to accumulate above the top of the lower primary air orice (LPAO, air vent at

front of rebox, just inside of door).

14. DISPOSAL OF ASHES Ashes should be placed in a steel container with a tight tting lid and moved outdoors

immediately. The closed container of ashes should be placed on a noncombustible oor or on the ground,

well away from all combustible materials, pending nal disposal. If the ashes are disposed of by burial in

soil or otherwise locally dispersed, they should be retained in the closed container until all cinders have

completely cooled. Other waste shall not be placed in this container.

15. To prevent injury, do not allow anyone to use this stove who is unfamiliar with the correct operation of the

stove.

Note: a licensed professional heating and cooling contractor should be consulted if you have questions

regarding the installation of this solid fuel burning appliance.

Safety Instructions

-3-

16. Do not operate stove while under the inuence of drugs or alcohol.

17. DO NOT ELEVATE THE FIRE. Build re directly on the bottom of the rebox. This stove has not been tested with

the use of grates, andirons or other means of elevating the re and must not be used.

18. During the rst 12 to 15 res. Additional smoke and odor may be emitted from the light oils used in construction

of the re box. This should disappear after a short period of time and not occur again. Persons with lung

conditions or owners of susceptible domestic pets (such as birds) should take prudent precautions. Open

windows and doors as needed to clear smoke and/or odor. Paint discoloration will occur if the stove is over

red.

19. This stove has a painted surface which is durable but it will not stand rough handling or abuse. When installing

your stove, use care in handling.

20. CLEAN STOVE FREQUENTLY as soot, creosote and ash may accumulate. Clean exterior with soap and warm

water when stove is not hot. Do not use any acids or scouring soap, as these solvents wear and dull the nish.

21. ALERT ALL PERSONS TO THE HAZARDS OF HIGH SURFACE TEMPERATURES while stove is in operation – especially

young children. Keep away from a hot stove to avoid burns or clothing ignition.

22. NEVER LEAVE SMALL CHILDREN UNSUPERVISED WHEN THEY ARE IN THE SAME ROOM AS THE STOVE. If small

children will be in the same room as the stove during operation, provide a sturdy barrier to keep them at a

safe distance from the stove.

23. Keep stove area clear and free from all combustible materials, gasoline, engine oil, naphtha and other

ammable vapors and liquids.

24. WHILE TENDING THE FIRE ALWAYS WEAR PROTECTIVE CLOTHING, re retardant hearth gloves and eye

protection, to prevent burns.

25. Never operate this stove with the door open except when re-fueling. Such actions can result in very dangerous

operating conditions.

26. DO NOT OVER FIRE THE STOVE. Over ring will occur if combustion air is uncontrolled as when feed door is left

open during operation. Such actions can result in very dangerous operating conditions. While in operation,

keep the feed door closed and secured at all times except while tending the re

27. When adding fuel be careful not to smother the re. Do not build res against glass and do not load fuel to

a height or in such a manner that it creates a hazard when opening the door.

28. NEVER LEAVE THE STOVE UNATTENDED with door open. Always close the door after ignition.

29. DO NOT CONNECT TO OR USE IN CONJUNCTION WITH ANY AIR DISTRIBUTION DUCT WORK UNLESS SPECIFICALLY

APPROVED FOR SUCH INSTALLATIONS.

30. A WOOD-BURNING STOVE MUST NEVER BE INSTALLED IN A HALLWAY OR NEAR A STAIRCASE, as it may block

egress in the event of a re.

31. DO NOT INSTALL IN A SLEEPING ROOM. DO NOT INSTALL IN AN ALCOVE OR INSIDE A FIREPLACE.

32. Install at least one smoke detector on each oor of your home. Detectors should be located away from

the heating appliance to avoid false alarms. Detectors should be located close to sleeping areas. Follow

the smoke detectors manufacturer’s placement and installation instructions. Maintain smoke detector per

manufacturer’s instructions.

33. CARBON MONOXIDE (CO) HAZARD. A buildup of CO fumes is toxic and can be fatal. Carbon Monoxide

is a colorless, odorless gas produced during combustion of wood, coal, oil, gas and by other fuel burning

appliances. It is important to have a proper draft and adequate replacement air ventilation so fumes

are drawn out the chimney. Installed as instructed this stove is designed to be as safe as possible yet it is

recommended to install a CO detector. Follow the manufacturer’s recommendations for proper installation

and use. It is recommended to be placed at table-top level (not near the ceiling) to avoid false alarms.

Realize that devices other than a stove (i.e. motor exhaust) can trigger CO alarms.

34. If alarm sounds:

• Recognize the symptoms of CO poisoning (headaches, nausea & drowsiness).

• Increase ventilation (open windows & doors).

• Make sure stove doors and/or lids are closed and secured.

• Check stove for smoking or pufng (open airow controls).

• Check chimney & connector pipe for leaks, blockage or down-draft conditions.

• Check CO device for false alarm.

• Keep power cords, electrical appliances and/or assemblies outside of the clearance area shown in this

manual for combustible materials.

35. Consult your municipal building department or re ofcials about restrictions, permits and installation

requirements for your area.

36. For further information on using your stove safely, obtain a copy of the National Fire Protection Association

(NFPA) publication, “Using Coal and Wood Stoves Safely” NFPA No. HS-10-1978. Write NFPA, Batterymarch

Park, Quincy, MA 02269.

-4-

Assembly Instructions

TOOLS AND MATERIALS REQUIRED FOR INSTALLATION

(NOTE: The following items are NOT included with your stove)

Tools:

• Pencil

• 6 foot Folding Rule or Tape Measure

• Tin Snips

• Drill: Hand or Electric

• 1/8” dia. Drill Bit (for sheet metal screws)

• Screwdrivers (blade and Phillips type)

• 14mm Nut Driver or Ratchet with 14mm Socket

• Safety Glasses

• Gloves

Materials:

• Chimney Connector Pipe: 6”/156mm dia. minimum

24 MSG black or 26 MSG blue steel straight stove

pipe or elbow(s).

• 1/2”/13mm Sheet Metal Screws.

• Chimney: Existing 6˝ Code-approved lined masonry

chimney or 6˝ inside dia. manufactured chimney

system listed to UL 103 HT (US)/ULC-S629 (CDN) listed

Furnace Cement (manufacturer recommends

Rutland Code 78 or equivalent)

1. Uncrate the stove and remove all packing materials and

protective poly bag. Remove the base skirting parts and

hardware pack from inside the rebox. NOTICE: DO NOT

REMOVE CERAMIC BLANKET material from inside stove pipe

opening (gure 1). This blanket provides an air seal on the

side walls of the stove to direct combustion gasses over the

secondary combustion tubes before exiting via the chimney.

DO NOT REMOVE THE CERAMIC BLANKET or your stove will not

operate properly.

2. Stove may be lightened for positioning by removing re brick.

Note position and arrangement of bricks. Firebrick, Ash Drawer

& Ash Cover MUST be replaced before use. DO NOT USE with

missing or cracked re brick.

3. Assemble the pedestal base skirting (gure 2). Attach two

corner pieces (07-30) to the center section (07-29) of skirting

and secure with four (4) 3/8˝ long truss head sheet metal

screws (07-31).

4. Attach the side skirting sections (07-27 & 07-28) to the corner

pieces and secure with four (4) truss head screws (07-31).

5. Slide the U-shaped skirting assembly around the pedestal base

and secure with two 1/4˝ long pan head sheet metal screws

(07-32) at the rear corners.

OPTIONAL BLOWER ASSEMBLY

1. For Optional Blower Assembly, note the position of the blower

opening in the rear of the stove (g. 3).

2. Place blower gasket onto blower assembly so as not to obstruct

the air ow from the fan.

3. Mount the blower assembly to the back of the stove aligning

the fan opening to the opening in the back of the stove.

Secure with four sheet metal screws.

4. After assembly, check to make sure re brick are properly

positioned and ash clean out cover is in place.

5. Route the power cord away from stove. Do not allow the

power cord to touch any hot surfaces. Keep power cord at

least 12˝ from stove surfaces.

6. Once stove is positioned, plug power cord into a grounded

120v outlet.

CAUTION: Stove is heavy. Make sure you have adequate help

and use proper lifting techniques whenever moving stove.

NOTICE: No warranty is granted, stated or implied, for the installation or maintenance of your wood stove

and assumes no responsibility of any incidental or consequential damages.

Figure 3 – Attach

Optional Blower

to Stove Body

Figure 1 – DO NOT remove ceramic blanket

from inside stove pipe opening. This is NOT

packing material but an integral component of

the stove combustion system.

DO NOT

REMOVE!

Figure 2

Base Skirting

-5-

LOCATING STOVE

1. The stove must be placed on solid concrete, solid masonry, or when installed on a combustible oor, on an

Underwriters Laboratories Listed Type 2 oor protector listed to UL standard UL 1618, such as Hy-C or Imperial

Model UL4056BK. Floor protector must be 1/2˝/13mm minimum thickness (R value = 1.19, K value = 0.84 see

page 23 for calculation formulas) non-combustible material or equivalent. The oor protector must extend

at least 18˝/46cm beyond the front of the access door, 8˝/21cm to the sides, 8˝/21cm beyond the rear and

must extend under and 2˝/50mm beyond either side of the stove pipe if it is elbowed towards a wall. (See

gures 4 – 6 and consult local building codes and re protection ordinances.)

2. The room in which the stove is installed must have a minimum oor to ceiling height of 8 ft. (2.4 m).

3. The stove must have its own ue. Do not connect this unit to a chimney ue serving other appliances. DO

NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM.

4. After observing the clearances to combustible materials (gures 4 – 6), locate your oor protector accordingly

(gure 4) and carefully place the stove in your selected location. Install connector pipe, elbows, and

thimble as required, utilizing either a recently cleaned and inspected 6˝/152mm lined masonry chimney or

a 6˝/152mm i.d. manufactured chimney system listed to UL 103 HT (US)/ULC-S629 (CDN).

5. Use round 6˝/152mm dia., minimum 24 MSG black or 26 MSG blue steel stove pipe to connect the stove

to the chimney. Do not use galvanized stove pipe. NOTE: Mobile home installations require double-wall UL

103 HT high-temp connector pipe. Secure connector pipe to the ue collar with three (3) equally spaced

sheet metal screws to rmly hold the pipe sections together. DO NOT CONNECT THIS STOVE TO ANY AIR

DISTRIBUTION OR DUCT SYSTEM.

6. Recheck clearances from the stove, connector stove pipe, and corner clearances using the illustrations in

gures 4 – 6 and your local building codes or re protection ordinances.

7. NOTICE: for installation in a manufactured/ mobile home (USA only), please see specic requirements on

page 10.

8. The clearances provided are minimum dimensions set by US standard UL 1482-2011 & ULC-S627-00, tested

and applied by OMNI-Test Laboratories, Inc. the manufacturer’s testing agency. Installation of this stove

must comply with the latest edition of NFPA 211 (US)/CAN/CSA-B365 (CDN) for reduced clearances and/or

your local building code rulings. Use whichever minimum dimensions are Clearances listed and shown MUST

be adhered to for safe operation of this appliance. CLEARANCES MAY NOT BE REDUCED BY ANY MEANS IN

USA OR CANADA.

9. This stove meets U.S. Test Standard: UL 1482- 2011& Canadian Standard: ULC-S627-00.

CAUTION: Fire hazard. Carpeting and other combustible material shall not cover the oor protector. These

materials must remain outside of combustible clearances, see g. 5 – 7

CAUTION: Keep furnishings and other combustible materials away from the stove.

NOTE: Before ring woodstove slide rebricks towards the rear so no gaps remain between bricks.

NOTE: Any wall containing combustible material such as wooden studs or drywall and faced with brick or

stone must be considered a combustible surface.

-6-

FLOOR

PROTECTOR

DASHED LINES SHOW HORIZONTAL CHIMNEY CONNECTOR

AND ADDITIONAL FLOOR PROTECTOR REQUIRED BENEATH

AND EXTENDING 2"/50.8mm BEYOND

EACH SIDE OF CONNECTOR PIPE

COMBUSTIBLE CONSTRUCTION IN ACCORDANCE WITH US NFPA 211

BACKWALL

SIDEWALL

30"/76.2cm

56"/142.3cm

18"/46cm min.

8"/21cm min.

24"/61cm

26"/66.1cm

min.

17"/

43.2cm

min

CLEARANCES | TOP VIEW

40"/

102cm

Minimum

Clearances

for installation

according to

UL 1482 (US) &

ULC-S627 (CDN)

Figure 5a – Front View Figure 5b – Side View

Minimum Clearance Dimensions

from Combustible Surfaces

Locating Stove

Figure 6 – Top View

Minimum Corner

Clearances from

Combustible Surfaces

18˝/46cm (US & CDN)

Figure. 4 – TOP VIEW Minimum Clearance Dimensions from

Combustible Surfaces

-7-

FIREBRICK ASSEMBLY

Firebrick extends the life of your stove and radiates heat more evenly. Check to see that all rebricks are in their

correct positions and have not become misaligned during shipping or assembly. If removed for ease of locating

stove, rebrick must be replaced before ring. See gures 7a – 7c, for proper positioning.

Fire Brick Dimensions (inches)

A-size: 9˝x4½˝x1¼˝

M-size: 9˝x2¼˝x1¼˝

XD-size: 8˝x4½˝x1¼˝†

XE-size: 9¾˝x1½˝x1¼˝

† XD bricks have offset notches to accommodate air tube side supports – see illustrations

CHIMNEY SIZING

Today’s solid fuel heating appliances are much more efcient than those made in the past. Your heating

appliance has been designed to provide the most efcient transfer of heat possible from the least amount of fuel.

Controlled combustion is the key to optimum heating performance. Controlled combustion requires a ow of

fresh air into the appliance, across the fuel and is nally exhausted up the chimney. Today’s high efciency stoves

transfer more heat into the living area and less up the chimney. Exhaust gases are typically at a lower temperature

than traditional type stoves. With lower exhaust temperatures, it is important that the chimney is correctly sized to

the stove. If the chimney diameter is too large, it will be difcult to raise the chimney ue temperature to provide

for adequate draft. This may result in a poor burn, smoke spillage, and rapid creosote creation. A 6”/152mm

diameter chimney is best suited for this stove. Your heating appliance must have a minimum of a 6”/152mm

diameter chimney. Maximum chimney diameter must not exceed 10˝ /254mm or have a cross sectional area

greater than 85 sq. in. /550cm2. Proper draft for this heating appliance is minimum of 0.05 w.c. (water column

measurement) and is required to prevent back pufng, smoke spillage and prevent safety hazards. Take into

account the chimney’s location to insure it is not too close to neighbors or in a valley which may cause unhealthy

or nuisance conditions.

IMPORTANCE OF PROPER DRAFT

Draft is the force which moves air from the appliance up through the chimney. The amount of draft in your

chimney depends on the length of the chimney, local geography, nearby obstructions and other factors. Too

much draft may cause excessive temperatures in the appliance. Inadequate draft may cause backpufng into

the room and ‘plugging’ of the chimney.

Inadequate draft will cause the appliance to leak smoke into the room through appliance and chimney

connector joints. An uncontrollable burn or excessive temperature indicates excessive draft.

CAUTION: Never operate stove with

missing or cracked re bricks!

Figure 7a – Step 1, Bottom

Firebrick Arrangement

Eight (8) A-size, Two (2) M-size,

Two (2) XD-size

Figure 7b– Step 2, Side

Firebrick Arrangement Four

(4) A-size, Two (2) M-size

Figure 7c– Step 3, Back

Firebrick Arrangement Four

(4) A-size, One (1) M-size

-8-

Connector pipe is used to make the connection from the nal positioning of your stove to an approved chimney.

Connector pipe is NOT included as part of the stove. Connector pipe must be 6”/152mm diameter minimum of

24 MSG (minimum standard gauge) black or 26 MSG blue steel stove pipe.

Any connector pipe used must be in good condition. Replace if necessary before using stove. Connector pipe is

not rated to provide close contact to combustible materials and must have proper clearance from combustible

materials as shown in the clearance diagrams on the previous pages. Connector pipe should never be used in

place of a chimney. If proper clearances are not observed a house re could result.

INSTALLATION INSTRUCTIONS

Please Note: Installation of a ue damper is NOT recommended. Combustion control is regulated by the intake

of combustion air, not the exhaust.

1. The crimped end of the stovepipe ts inside the stove ue collar. Secure with three (3) equally spaced sheet

metal screws. The rst section of connector pipe must be single walled to properly attach to the stove collar.

Install additional pipe and elbow with the crimped end towards the stove. This will allow any condensation

in the ue to run back into the rebox.

2. Horizontal pipe runs must slope upwards towards the chimney at least 1/4˝/6.4mm per foot of horizontal run.

3. You must have at least 18˝/457mm of clearance between any horizontal piping and the ceiling.

4. The pipe cannot extend into the chimney ue (gure 8).

5. Secure all pipe/elbow sections with three (3) equally spaced sheet metal screws at each joint to make the

piping rigid. DO NOT CONNECT THIS STOVE TO ANY AIR DISTRIBUTION DUCT OR SYSTEM.

6. It is recommended that no more than two (2) 90° bends be used in the stovepipe installation. The use of

more than two 90° bends may decrease the amount of draw and possibly cause smoke spillage. Where

possible, use only corrugated (non adjustable) elbows. These provide a better seal.

7. The connector pipe must not pass through an attic or roof space, trusses, closet, or any concealed space,

oor, ceiling, wall, or combustible construction. (See Chimney Connector Systems & Clearances, page

13.) A manufactured chimney system listed to UL 103 HT (US)/ULC-S629 (CDN) must be used from the rst

penetration of ceiling or wall to the chimney cap. Where passage through a wall or partition of combustible

construction is desired, the installation shall conform to NFPA 211 (USA) or CAN/CSA-B365 (Canada).

Connector Pipe Installation

Figure 8 – Stovepipe/Flue Connections

NOTE: Connector pipe is not included. To purchase, visit your local hardware, home, or building center. See

“locating stove” page 6 for additional specications.

NOTICE: For mobile home installations (US only), connector pipe must be double-wall, high-tempurature pipe

that meets ul 103 ht specications.

WARNING: Do not use single wall connector pipe as a chimney - a house re could result.

-9-

Mobile Home Installation Instructions

This stove is approved for mobile home installation

in the USA only (DO NOT INSTALL IN MOBILE HOMES

IN CANADA). In addition to the installation and

safety instructions, the following requirements are

MANDATORY for installation in a mobile home.

All mobile home installations must be made in

accordance to Manufactured Home and Safety

Standard (HUD), CFR 3280, part 24.

1. The stove must be permanently bolted to

the oor to prevent movement of the stove.

Movement of the stove could separate the

outdoor air connection and/or chimney

connection and create an unsafe operating

condition.. Examine oor structural members

to make sure that the weight of the installation

can be supported.

2. CAUTION: THE STRUCTURAL INTEGRITY OF THE

MOBILE HOME FLOOR, WALL, AND CEILING/

ROOF MUST BE MAINTAINED.

3. The stove must be electrically grounded to

the steel frame of the Mobile Home. The stove

must be grounded using a #8 ga. ground wire

with approved termination and star washer.

4. The oor protection and specied clearances

noted elsewhere in this manual must be

maintained.

5. The unit must have a permanent outside air

source for combustion. The combustion air

intake system must be of metal construction.

Minimum diameter for the intake ducting is

5 inches. The air intake must be screened to

prevent the entrance of rodents. The outside

air inlet must be kept free of leaves, snow, ice,

or other debris that could restrict air supply

when the appliance is in operation. Fresh Air

Kit Model FAK-07 is compatible with this unit.

Kit is available at www.vogelzang.com or

your local retailer.

6. WARNING: DO NOT INSTALL IN A SLEEPING ROOM.

7. WARNING: DO NOT USE SINGLE WALL CONNECTOR PIPE ANYWHERE IN A MOBILE HOME INSTALLATION. A

listed double-wall chimney connector system, ceiling thimble, roof thimble, spark arrestor, and roof ashing

suitable for use in Mobile Homes must be used. All components of the chimney and connector system must

be of the HT type and listed to UL 103 HT. Install per chimney manufacturer’s instructions.

8. The openings in the chimney cap must not permit the entrance of a 3/4˝/19mm diameter rod.

9. If the chimney exits the Mobile Home at a location other than through the roof, and exits a point 7 ft. /21.3m

or less above the ground upon which the Mobile Home is set upon, a guard shall be tted at the point of exit

up to 7 ft./21.3m.

10. The chimney shall be attached directly to the room heater and shall extend at least 3 ft./91.4cm above the

part of the roof through which it passes. The top of the chimney must project at least 2 ft./60.1cm above the

highest elevation of any part of the Mobile Home within 10 ft./3.1m of the chimney.

11. Use silicone to seal at the location where the chimney and fresh air supply system penetrates the exterior of

the structure.

12. The chimney system must comply with all local requirements.

Figure 9 – Mobile Home Installation

-10-

The stove must be connected to either a lined masonry or manufactured metal chimney built and tested to the

specications listed on the previous pages.

Chimneys perform two functions:

1. As a means of exhausting smoke and ue gases which are the result of fuel combustion.

2. The chimney (only) provides “draft” which allows oxygen to be continuously introduced into the appliance,

so that proper combustion is possible. This stove relies on natural draft to operate.

NOTICE: Always provide a source of fresh air into the room where the stove is located. Failure to do so may result

in air starvation of other fuel burning appliances and the possible development of hazardous conditions.

A stove DOES NOT create draft. Draft is provided by the chimney. To achieve proper draft your chimney must

meet the four minimum height requirements detailed in gures 11–13. If these minimum requirements are not met

your stove will not operate properly. A minimum of 0.05 w.c. (measured in water column) is required for proper

drafting to prevent back pufng, smoke spillage, and to maximize performance. (Gauges to measure draft are

readily available at stove stores and are economical to rent or purchase.) Factors such as wind, barometric

pressure, trees, terrain and chimney temperature can have an adverse effect on the draft. The manufacturer

cannot be held responsible for external factors leading to less than optimal drafting. Should you have a problem

with inadequate draft, you should contact a licensed heating and cooling contractor for assistance in solving the

problem. For a more in-depth explanation see Chimney Draft.

IMPORTANT INSTALLATION POINTS

1. Size chimney ue to stove collar. This stove requires a minimum of a 6”/152mm diameter ue.

2. Never connect this unit to a chimney serving another appliance.

3. The chimney must meet all minimum height requirements.

4. Never use a chimney to ventilate a cellar or basement.

5. Contact your local building authority for approved methods of installation and any necessary permits and/

or inspections.

MASONRY CHIMNEY

The chimney must be a code-approved, masonry

chimney with ue liner. Before using an existing

masonry chimney, clean the chimney, inspect the

ue liner and make any repairs needed to be sure

it is safe to use. Make repairs before attaching the

stove. The connector stove pipe and ttings you will

need to connect directly to a lined masonry chimney

are shown in gure 10. If the connector stove pipe

must go through a combustible wall before entering

the masonry chimney, consult a qualied mason or

chimney dealer. The installation must conform to local

building and re codes and latest edition of NFPA 211

US or CAN/CSA-B365. If there is a clean out opening in

the base of the chimney, close it tightly.

Chimney Connections

CHIMNEY

FLUE

5/8" TILE

CHIMNEY

LINER

MASONRY

CHIMNEY

THIMBLE

COLLAR

6˝ ROUND

24 ga. BLACK

CONNECTOR

STOVEPIPE

8˝ MIN.

LINER

BELOW

ENTRY

HOLE

Figure 10 - Masonry Chimney Connection

CHIMNEY

FLUE

5/8" TILE

CHIMNEY

LINER

MASONRY

CHIMNEY

THIMBLE

COLLAR

6˝ ROUND

24 ga. BLACK

CONNECTOR

STOVEPIPE

8˝ MIN.

LINER

BELOW

ENTRY

HOLE

Figure 11 - Chimney Construction through Attic Space

-11-

Chimney Minimum Height Requirements:

1. Overall Height – 15 ft./4.6m min.

2. Height above roof – 3 ft./91cm

3. Height above slope – 2 ft./61cm min. within 10

ft./3.05m

4. Minimum rise before horiz. section – 24 in./61cm

NOTICE: If minimum chimney requirements are not

met, your stove will not operate properly.

Figure 13 - Chimney Connection to

Firebox through Masonry Wall

MANUFACTURED CHIMNEY

REFER TO CHIMNEY AND CHIMNEY CONNECTOR MAKER’S

INSTRUCTIONS FOR INSTALLATION AND USE.

Use only 6˝/152mm diameter manufactured chimney

system listed to UL 103 HT (US) or ULC-S629 (CDN).

Chimney made to this listing is High Temperature rated to

2100°F/1149°C. Use chimney from only one manufacturer.

Never mix brands. Carefully follow the chimney

manufacturer’s stated requirements and clearances.

Use the chimney manufacturer’s attic guards, roof

supports, ashing and re stops when passing through a

ceiling. Use a listed wall pass-thru when passing through

a combustible wall. Do not use makeshift compromises

during installation.

WARNING: DO NOT USE A SINGLE-WALL CONNECTION

PIPE AS A CHIMNEY!

When using a pre-existing chimney, have its condition

and installation inspected before using. Make sure that

the chimney meets all of the UL rating requirements listed

above. Be aware that not all manufactured chimney is

UL 103 HT/ULC-S629 rated. NOTE: It is recommended that

you contact a licensed heating and cooling contractor

(consult your local yellow pages) for chimney installation.

Manufactured chimney with the proper required UL/ULC

listing is available from most home centers, hardware

stores, and HVAC supply stores. You may wish to view

chimney manufacturers’ information on-line. See, www.

duravent.com, www.selkirkinc.com or www.mtlfab.com.

VENTING TO EXISTING FIREPLACE

In some instances, people desire to convert an existing

replace for stove use. Usually, safe connection to an

existing masonry chimney requires more work than using

a prefabricated chimney. The existing replace must be

closed and sealed at the damper with high-temperature

caulk, ceramic wool, or furnace cement. Prior to

installation, clean and inspect the existing ue and smoke

shelf. Installation should be designed so the system can

be dismantled for periodic cleaning and inspection.

Before conversion, make sure the existing chimney is

structurally sound, the chimney incorporates a ue liner

and make sure it is in good condition. (A ue liner consists

of clay tile that protects the brickwork of a chimney. If a

chimney does not have a liner, or it is damaged, have it

relined by a professional. Do Not use a chimney that is

unlined or damaged! If you have any question regarding

the condition of the chimney, consult a qualied licensed

contractor, qualied engineer, competent mason, cer

tied Chimney Sweep, or a knowledgeable inspector.

Consult your insurance company if you cannot nd a

qualied expert.

-12-

CAUTION: Not all replace chimneys are suitable for conversion to accommodate connection to a wood

stove. Check with a qualied expert.

Many prefabricated replaces are of the “zeroclearance replace” category. These consist of multi layered

metal construction. They are designed with enough insulation and/or air cooling on the base, back and sides so

they can be safely installed in direct contact with combustible oors and walls. Although many prefabricated

replaces carry endorsements from nationally recognized organizations for use as replaces, they have not been

tested for connection to wood stove heaters. Connecting a stove to such a device will void the manufacturer’s

warranty. Venting a stove directly into a replace does not meet code and should not be attempted. The stove

warranty will be void with such an installation. Do not create a hazard in your home by connecting in this manner.

FIREPLACE INSTALLATION

NOTE: DO NOT ATTEMPT TO ROUTE THE CHIMNEY CONNECTOR PIPE THROUGH THE THROAT OF THE FIREPLACE.

Directly connecting the stovepipe into the existing masonry chimney (gure 14 “Type A” Fireplace Conversion) of

the replace is the ONLY approved method of installation. If the chimney is behind a combustible wall, you must

use an approved wall passthrough system to gain access to the chimney. This is a complicated and involved

process and to ensure safety should only be done by a qualied installer.

1. An entry hole must be cut through the masonry and tile liner with minimal damage to the liner. At least

8˝/203mm of liner must remain below the entry position. When locating the stove and stovepipe, all minimum

clearances must be observed from combustible surfaces including mantels, combustible trim work, ceilings,

and walls. Positioning the center of the stove pipe entry into the chimney 24˝/61cm below the ceiling should

insure proper clearance for a 6˝/152mm stovepipe.

2. Install a re clay (5/8˝/16mm minimum thickness) thimble. Make sure the thimble is ush with the inner surface

of the chimney liner and does not protrude into the ue (see gure 9 on page 9).

3. Secure the thimble with refractory mortar. The thimble should be surrounded by 12˝/305mm of solid unit

masonry brickwork or 24˝/61cm of stone.

4. Install the stovepipe into the thimble as far as possible without extending past the ue lining.

5. A small airspace (about 1/2˝/13mm) should remain between the stovepipe and thimble to allow for

expansion of the pipe. Seal this airspace with high temperature caulking or ceramic wool.

6. Secure and seal the damper in the closed position using high-temp caulking, ceramic wool, or furnace

cement. Also check to see if the chimney has a clean out.

If it does, make sure it is closed and sealed as well. A leaky clean out will greatly reduce draft efciency. If

you have any questions regarding venting your stove, contact the manufacturer or contact the National Fire

Protection Association (NFPA) and request a copy of the latest editions of NFPA Standard 211 and NFPA Standard

908. Their address is: Battery March Park, Quincy, MA 02269.

Figure 14 - Fireplace Conversion

-13-

CHIMNEY CONNECTOR SYSTEMS & CLEARANCES

NFPA 211 (US) NOTE: In Canada, installation must

conform to CAN/CSA-B365 when passing through

combustible construction.

A. Brick Masonry - Minimum 3.5˝/89mm thick brick

masonry all framed into combustible wall with a

minimum of 12˝/305mm brick separation from

clay liner to combustibles. The reclay liner shall

run from outer surface of brick wall to, but not

beyond, the inner surface of chimney ue liner

and shall be rmly cemented in place.

B. Insulated Sleeve - Solid-insulated, listed factory-

built chimney length of the same inside

diameter as the chimney connector and having

1˝/25.4cm or more of insulation with a minimum

9˝/229mm air space between the outer wall of

the chimney length and combustibles.

C. Ventilated Thimble - Sheet steel chimney

connector, minimum 24 gauge in thickness,

with a ventilated thimble, minimum 24 gauge in

thickness, having two 1˝/25.4mm air channels,

separated from combustibles by a minimum

of 6˝/152mm of glass ber insulation. Opening

shall be covered, and thimble supported with

a sheet steel support, minimum 24 gauge in

thickness.

D. Chimney Section Pass-through - Solid insulated,

listed factory-built chimney length with an inside

diameter 2˝/51mm larger than the chimney

connector and having 1˝/25.4mm or more

of insulation, serving as a pass-through for a

single wall sheet steel chimney connector of

minimum 24 gauge thickness, with a minimum

2˝/51mm air space between the outer wall of

chimney section and combustibles. Minimum

length of chimney section shall be 12˝/305mm

chimney section spaced 1˝/25.4mm away from

connector using sheet steel support plates on

both ends of chimney section. Opening shall

be covered, and chimney section supported

on both sides with sheet steel support securely

fastened to wall surfaces of minimum 24 gauge

thickness. Fasteners used to secure chimney

section shall not penetrate chimney ue liner.

-14-

OPERATING SAFETY PRECAUTIONS

1. Never overre this stove by building excessively hot res as a house/ building re may result. You are overring

the stove if unit or stovepipe begins to glow or turn red.

2. Never build extremely large res in this type of stove as damage to the stove or smoke leakage may result

3. Do not build re too close to glass.

4. Unit is hot while in operation. Keep children, clothing, and furniture away. Contact may cause skin burns. Do

not touch the stove after ring until it has cooled.

5. Provide air into the room for proper combustion.

6. Inspect stovepipe every 60 days. Replace immediately if stovepipe is rusting or leaking smoke into the room.

7. Attempts to achieve heat output rates that exceed heater design specications can result in permanent

damage to the heater.

THIS STOVE IS DESIGNED TO BURN NATURAL WOOD FUEL ONLY!

Hardwood, 18˝ to 20˝ / 45cm to 50cm should be air dried (seasoned), for a minimum of 6 months. Logs grater

than 6˝/152mm in diameter should be split. Wood should be stored in a dry, well ventilated area. The humidity

content for usable rewood must be less than 20% of the weight of the log. This heater is designed to burn natural

wood only. Higher efciencies and lower emissions generally result when burning air dried seasoned hardwoods,

as compared to softwoods or to green or freshly cut hardwoods.

Attempts to use wet or unseasoned wood will cause:

- ignition problems - rapid creosote build-up resulting in chimney re

- incomplete combustion - low heat yield

- blackened glass

DO NOT BURN:

1. Garbage;

2. Lawn clippings or yard waste;

3. Materials containing rubber, including tires;

4. Materials containing plastic;

5. Waste petroleum products, paints or paint thinners,

or asphalt products;

6. Materials containing asbestos;

7. Construction or demolition debris;

8. Railroad ties or pressure-treated wood;

9. Manure or animal remains;

10. Salt water driftwood or other previously salt water

saturated materials;

11. Unseasoned wood; or

12. Paper products, cardboard, plywood, or

particleboard. The prohibition against burning

these materials does not prohibit the use of re

starters made from paper, cardboard, saw dust,

wax and similar substances for the purpose of

starting a re in an affected wood heater.

Burning these materials may result in release of toxic fumes or render the heater ineffective and cause smoke.

Dead wood lying on the forest oor should be considered wet, and requires full seasoning time. Standing dead

wood can usually be considered to be about 2/3 seasoned. Splitting and stacking wood before it is stored

accelerates drying time. Storing wood on an elevated surface from the ground and under a cover or covered

area from rain or snow also accelerates drying time. A good indicator if wood is ready to burn is to check the

piece ends. If there are cracks radiating in all directions from the center then the wood should be dry enough

to burn. If your wood sizzles in the re, even though the surface is dry, it may not be fully cured, and should be

seasoned longer.

Operating Instructions

Caution: House Fire Hazards

• Do not store wood on oor protector, underneath stovepipe or anywhere within minimum clearances from

combustible surfaces specied for this stove.

• Overring may cause a house re. You are overring if a unit or chimney connector glows red.

Warning: Explosion Hazard

• Never use chemicals, gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter uid, or similar

ammable liquids to start or “freshen-up” a re in the stove.

• Keep all ammable liquids, especially gasoline, out of the vicinity of the stove— whether in use or in

storage.

-15-

OPTIMAL FUEL CONSUMPTION

This stove is designed to get the most efcient transfer of heat energy from the wood fuel and radiate it into your

living environment. The re box introduces combustion air through four sources. (1) Immediately beneath the door

opening below the window is a Lower Primary Air Orice (LPAO). (2) The primary air inlet control (center control

lever) brings air into the rebox and controls the rate of burn (and the amount of heat the stove radiates). (3)

The high burn duct control (right control lever) provides additional air for maximum burn rate. (4) The secondary

air tubes at the top of the rebox are designed to ignite the combustion gases (smoke) given off by the burning

wood and increases the efciency of the stove and reduces chimney emissions. Smoke given off by burning

fuel consists of very small organic liquid droplets. If these droplets condense, they form a sticky tar-like substance

called creosote. When operated properly, this stove is designed to burn these droplets. Burning these droplets

releases heat that would otherwise be lost up the chimney as smoke. Following the instructions below will help

you operate your stove properly to maximize the stove’s performance. Actual performance is dependent on

chimney height, weather, log size, wood species and moisture content. Some experimentation will initially be

required to nd that “sweet spot” where your stove performs best. The following will give you a starting point to

nd your optimum settings.

TAMPER WARNING

This wood heater has a manufacturer-set minimum low burn rate that must not be altered. It is against federal

regulations to alter this setting or otherwise operate this wood heater in a manner inconsistent with operating

instructions in this manual.

EFFICIENCIES

Efciencies can be based on either the lower heating value (LHV) or the higher heating value (HHV) of the fuel.

The lower heating value is when water leaves the combustion process as a vapor, in the case of woodstoves the

moisture in the wood being burned leaves the stove as a vapor. The higher heating value is when water leaves

the combustion process completely condensed. In the case of woodstoves this would assume the exhaust gases

are room temperature when leaving the system, and therefore calculations using this heating value consider

the heat going up the chimney as lost energy. Therefore, efciency calculated using the lower heating value of

wood will be higher than efciency calculated using the higher heating value. In the United States all woodstove

efciencies should be calculated using the higher heating value.

The best way to achieve optimum efciencies is to learn the burn characteristic of you appliance and burn well-

seasoned wood. Higher burn rates are not always the best heating burn rates; after a good re is established a

lower burn rate may be a better option for efcient heating. A lower burn rate slows the ow of usable heat out

of the home through the chimney, and it also consumes less wood.

When rst loading fuel set the primary air inlet control (center) at the wide open (push in) position for at least

15–20 minutes (the high burn duct control should be closed – pulled out – when starting res). When the stove is

working properly you should be able to observe secondary combustion ames above the fuel pieces in front of

the secondary air tubes at the top of the rebox. These secondary ames should continue to burn after the primary

air inlet is reset from wide open to the desired operating setting. If the ames do not continue to burn, open the air

control to re-establish the secondary ames then slowly reset the air control to the desired setting. Initially it may

take several attempts to gure your stove out. But once you nd the operating “sweet spot” and the correct mix

of procedures to get there, only minor adjustments will be necessary. The best indicator of a properly operating

stove is to look for smoke coming out of the chimney. You may see steam emissions that will quickly dissipate.

Smoke will thin but continue to drift without totally disappearing. If you do detect smoke emissions, open the air

control a little bit, let the stove adjust for 10–15 minutes and re-check your chimney. Remember – visible smoke

represents lost heat.

NOTICE - INITIAL BURNS TO CURE PAINT BECAUSE OF THE HIGH OPERATING TEMPERATURES, THIS STOVE USES A

SPECIAL HIGH-TEMP PAINT WHICH REQUIRES A SERIES OF BURNS TO CURE THE PAINT FOR DURABILITY AND A LIFETIME

OF SERVICE.

Proper curing of the high-temp paint requires a series of three initial burns. The stove should be allowed to cool

off between each burn. The rst two burns should be small res and low temperatures (250°F/120°C) for a duration

of 20 minutes each. The third re should be at a medium-high temperature (500 to 700°F/260 to 370°C) for twenty

minutes. Provide adequate cross ventilation to clear any smoke or odor caused by initial rings.

Notice: Use solid wood materials only. Do not burn garbage or ammable uids such as gasoline, naphtha

or engine oil. Do not use coal. This stove is not designed to accommodate the air ow (draft) necessary to

properly burn coal or coal products. Do not elevate re or use grates or andirons. Build re directly on bottom

of rebox.

-16-

STARTING A FIRE

DO NOT LEAVE STOVE UNATTENDED WITH DOOR OPEN! The top down method of re building is recommended

for this appliance. After making sure that the stove air intake controls are fully open (completely pull-out towards

you), Place the largest pieces of wood on the bottom, laid in parallel and close together. Smaller pieces are

placed in a second layer, crossways to the rst. A third layer of still smaller pieces is laid crossways to the second,

this time with some spaces between. Then a fourth layer of loose, small kindling and twisted newspaper sheets

tops off the pile.

Add large pieces of wood as the re progresses being careful not to overload. (Do not ll rebox beyond rebrick

area.) An ideal coal bed of 1˝ – 2˝ (25mm - 50mm) should be established to achieve optimum performance.

This unit is designed to function most effectively when air is allowed to circulate to all areas of the rebox. TIP: If

ash or coals remain in the stove, make sure to clear them away from the Lower Primary Air Orice (LPAO) and

rake a slight (1˝ – 2˝/25mm-50mm wide) trough down the center of the coal bed from front to back prior to

loading the fuel. Once fuel has been loaded, close the door and leave the air inlet control fully open until re is

well established (at least 15–20 minutes) being careful not to over re (if any of the exterior parts of the stove or

chimney connections begin to glow you are over ring the stove). Re-adjust the primary air inlet control (A) to

desired burn rate. For “low” setting pull the primary air control (center control) all the way out, for “high” push

all the way back. (If excessive smoke lls the rebox, open air inlet control slightly until ames resume and wood

is sufciently ignited.) The basic rule of thumb is “closed (pull out) = low,” “half way open = medium” and “fully

open (push in) = high.” The high burn control lever (B) is used to deliver additional air to an established re when

the primary control is set at 3⁄4 to fully open (all the way in) position. Push the secondary (right) control in to open/

high burn position. When adjusting the primary air to a lower setting, close (pull out) the high burn (right, 3/4 lever)

by pulling control fully out.

1. Set Primary Air Inlet Control Lever “A” to fully open by pushing the center control lever (located under hearth

plate) inward toward the rear of stove. Set the Secondary Air (High Burn) Control Lever “B” to the closed

position by pulling the lever fully out. NOTE: OPEN/HIGH = IN; CLOSED/LOW = OUT (see iIlustrations below)

2. Open the feed door and place several wads of crushed paper in the rebox. Cover the paper with a few

pieces of small kindling wood.

3. Ignite the paper and leave the door slightly open until the kindling re is established. Close and secure the

door. DO NOT LEAVE STOVE UNATTENDED WITH THE DOOR OPEN! Slowly add additional wood, adding larger

pieces as the re progresses.

4. Once the re is fully established you may select the desired burn rate. Be careful not to over re the stove.

SETTINGS

CONTROL

LEVER

(Primary Air)

CONTROL

LEVER

(High Burn)

OPEN

CLOSED

OPEN

CLOSED

HEARTH

CONTROL

LEVER

(Primary Air)

CONTROL

LEVER

(High Burn)

OPEN

CLOSED

OPEN

CLOSED

HEARTH

CONTROL

LEVER

(Primary Air)

CONTROL

LEVER

(High Burn)

OPEN

CLOSED

OPEN

CLOSED

HEARTH

CONTROL

LEVER

(Primary Air)

CONTROL

LEVER

(High Burn)

OPEN

CLOSED

OPEN

CLOSED

HEARTH

CONTROL

LEVER

(Primary Air)

CONTROL

LEVER

(High Burn)

OPEN

CLOSED

OPEN

CLOSED

HEARTH

CONTROL

LEVER

(Primary Air)

CONTROL

LEVER

(High Burn)

OPEN

CLOSED

OPEN

CLOSED

HEARTH

CONTROL

LEVER

(Primary Air)

CONTROL

LEVER

(High Burn)

OPEN

CLOSED

OPEN

CLOSED

HEARTH

CONTROL

LEVER

(Primary Air)

CONTROL

LEVER

(High Burn)

OPEN

CLOSED

OPEN

CLOSED

HEARTH

-17-

ADDING FUEL

If the coal bed is not hot and glowing, rake the coals to the front of the stove, close the door and adjust the

primary air inlet control to the wide open position. Let the coals re-heat for 10–15 minutes. When hot and glowing,

spread them out and place your next fuel load into the stove (make sure no coals or ashes block the LPAO).

Leave the primary air inlet control in the wide open (pushed in) position for 15–20 minutes. Fuel load size can vary

but should be kept 1–2˝

(25mm-50mm) below the secondary air tubes. Also position the fuel to leave space so the air from the inlet can

work between the pieces of fuel. This reduces the time it takes for new fuel to burn properly.

1. When refueling, adjust primary air inlet (center) control to the fully open (pushed in) position. When re

brightens, slowly and carefully open the door. This procedure will prevent unburned gases from igniting

causing smoke and ame spillage.

2. When adding fuel be careful not to hit, bump or damage the ceramic bafe board located at the top of

the rebox.

3. Add fuel being careful not to overload or over re the stove.

4. When adding fuel be careful not to smother the re. Do not build res against glass and make sure the coal

bed does not obstruct the air inlet. Do not load fuel to a height or in such a manner that it creates a hazard

when opening the door.

5. Close the feed door and secure tightly.

6. Adjust the air inlet control as described above.

7. Empty ashes regularly. Do not allow ashes to pile up (see Safety Instructions #14 on page 2.)

8. Properly dispose of hot ashes (see Safety Instructions, item #14 on page 2.)

9. Do not over re the stove (over ring is when any part of the stove exterior or chimney connections glow).

VISIBLE SMOKE

The amount of visible smoke being produced can be an effective method of determining how efciently the

combustion process is taking place at the given settings. Visible smoke consist of unburned fuel and moisture

leaving your stove. Learn to adjust the air settings of your specic unit to produce the smallest amount of visible

smoke. Wood that has not been seasoned properly and has a high wood moisture content will produce excess

visible smoke and burn poorly.

-18-

Chimney Connections

Caution: Do not over re appliance. You are over ring if the chimney connectors or stove glows red. Close

the door and immediately shut all air controls (pull out) to reduce the air supply and slow down the re.

Caution: Slow burning res and extended use may cause excessive creosote buildup. Ignition of creosote or

over ring may cause a chimney re. Chimney res burn extremely hot and may ignite surrounding materials.

In case of a chimney re call the re department immediately.

OPERATIONAL TIPS

• Get the appliance hot and establish a good coal bed before adjusting to a low burn rate (this may take 30

minutes or more depending on your wood)

• Use smaller pieces of wood during start-up and a high burn rate to increase the stove temperature

• Be considerate of the environment and only burn dry wood

• Burn small, intense res instead of large, slow burning res when possible

• Learn your appliance’s operating characteristics to obtain optimum performance

• Burning unseasoned wet wood only hurts your stoves efciency and leads to accelerated creosote buildup

in your chimney

Caution: risk of re when wood is burned slowly, it produces tar and other organic vapors, which combine

with expelled moisture to form creosote. The creosote vapors condense in the relatively cool chimney ue

of a slow-burning re. As a result, creosote residue accumulates on the ue lining. When ignited this creosote

makes an extremely hot re. The chimney connector and chimney should be inspected at least once every

two months during the heating season to determine if a creosote buildup has occurred. If creosote has

accumulated (3mm or more) it should be removed to reduce the risk of a chimney re.

Warning: In Case Of Chimney Fire

1. Close air inlet control

2. Get out of the house

3. Call the re department.

CHIMNEY DRAFT

The chimney is critical to the proper operation of the stove. It is the chimney that creates draft; THE STOVE DOES

NOT AND CANNOT CREATE DRAFT. The chimney provides two vital functions for proper stove operation. First, it is

the passage to exhaust smoke and hot gases created in the combustion process. Secondly, it supplies the draft (or

pressure) to bring oxygen to the re to sustain combustion. Draft is the natural movement of air or gases through a

chimney. Chimney draft comes from the natural tendency for hot (less dense) air to rise. As the hot air rises within

the chimney it creates a lower pressure at the bottom of the chimney to which the stove is connected. The higher

pressure air outside the stove then rushes into the stove where the lower air pressure level exists, thus bringing

oxygen to the re. This constant ow of air is referred to as the draft. Many factors or combination of factors can

act together to build or impede the draft. Without the correct amount of draft, the stove will not operate properly.

If there is excessive draft, an unsafe condition will arise with too much air being drawn into the stove and creating

an excessively hot re. This could cause over ring which runs the risk of igniting structural elements around the

stove and chimney. The most common experience is that of insufcient draft. Under insufcient draft conditions,

the re will be starved for oxygen, improper or incomplete combustion occurs resulting in smoke spillage into the

area around the stove. A re that is starved for oxygen will not burn well. Such a re will produce excessive smoke

that will cool and condense in the chimney creating creosote. Excessive amounts of creosote buildup can ignite

causing a chimney re with the possibility of structural elements igniting as well. Correct any draft related issues

before using the stove. The following are some possible causes of insufcient draft. Please note that one or more

factors may play a role in a draft issue and certain factors may change over time as conditions vary.

-19-

1. Atmospheric Pressure and Air Supply Atmospheric pressure that affects the draft may occur from outside

the structure, inside the structure, or both. High pressure weather (clear and cold) usually produces a better

chimney draft than low pressure (overcast and damp) conditions. Negative pressure can be created inside

a home by appliances that expel air from within such as bathroom vents, range hoods, clothes dryers, and

forced air furnaces. Do not allow such appliances to overcome the natural draft. Note that newer homes

tend to be built more tightly allowing less make upair to seep freely in. Negative pressure may be overcome

by opening a nearby door or window. In extreme conditions of negative draft, the airow in the chimney will

reverse direction. This is known as “down drafting.”

2. Environmental Factor - Wind or air deecting off external objects such as the roof, neighboring structures,

trees, or hills. These can cause a pressure change in the air surrounding the chimney.

3. Chimney Temperature - The temperature of the chimney is an important factor in how well it drafts. Warm

chimneys draft better than cold chimneys. This is based upon the principle that hot air rises while cold air

sinks. Hot gases going up a cold chimney will cool rapidly. Warm the chimney by allowing a hot re to burn

for the rst fteen to thirty minutes after starting the re. Be careful not to over re the stove. If any part of the

stove or chimney starts to glow, you are over ring the stove. Masonry chimneys will take longer to warm than

manufactured chimneys on account of their greater structural mass. Chimneys that have a ue diameter

larger than the stove outlet take more heat to warm, thus resulting in a faster cooling of the hot gases

needed to build or maintain draft.

4. Chimney Installation and Maintenance - Conrm that all four minimum chimney height requirements listed

in the Chimney Connection section of the manual have been met. The physics that link chimney height

with draft creation are vital to the proper operation of the stove. Failure to meet each of these minimum

requirements will have an adverse affect on draft. Avoid long horizontal runs or multiple elbows. Use stove

cement to seal joints in the connector pipe section. Regularly clean the chimney, connector pipe, rain cap,

and spark arrestor screen. Creosote build up can reduce the chimney draw and possibly create a chimney

re.

5. Temporarily Out of Operation - After the re has burned out, open the air control to its fully open position.

This will allow warm room air to enter the chimney and keep it as warm as possible until the stove is used

again. For assistance involving chimney draft issues, contact a knowledgeable licensed heating and cooling

contractor in your area. For questions regarding manufactured chimney, contact the manufacturer of the

chimney.

NOTE: A DRAFT READING OF 0.05 TO 0.06 W.C. (WATER COLUMN) IS REQUIRED FOR PROPER BURNING OF THIS

STOVE.

AIR TUBES

The air tubes assembled in this unit are designed to provide an accurate mix of secondary air to insure the

highest efciency. Any damage or deterioration of these tubes may reduce the efciency of combustion. The

air tubes are held in position by either screws or snap pins. Locate these to either side of the tube and remove to

allow the tube to be removed and replaced.

CREOSOTE – FORMATION AND NEED FOR REMOVAL

Failure to remove creosote may result in ignition and may cause a house/building re. Creosote may be removed

using a chimney brush or other commonly available materials from your local hardware retailer. Chimney res

burn very hot. If the unit or chimney connector should glow red, reduce the re by closing the inlet air control

and immediately call the re department. A re in the rebox may be smothered by pouring a large quantity of

coarse salt, baking soda, or cool ashes on top of the re.

ASH DISPOSAL

Whenever ashes get 3 to 4 inches deep in your rebox or ash pan, and when the re has burned down and

cooled, remove excess ashes. Leave an ash bed approximately 1 inch deep on the rebox bottom to help

maintain a hot charcoal bed. Ashes should be placed in a metal container with a tight-tting lid. The closed

container of ashes should be placed on a noncombustible oor or on the ground, away from all combustible

materials, pending nal disposal. The ashes should be retained in the closed container until all cinders have

thoroughly cooled.

Service Hints

Caution: A chimney re may cause ignition of wall studs or rafters which were assumed to be a safe distance

from the chimney. If a chimney re has occurred, have your chimney inspected by a qualied expert before

using again.

-20-

PREVENTING CREOSOTE BUILDUP

1. Creosote will inevitably form in your chimney and connector pipe. Following these steps will help reduce the

rate of build up.

2. BURN ONLY SEASONED WOOD that has dried for at least one year. (<20% humidity by weight)

3. Burn hardwood rather than softwood. Hardwood is denser or heavier wood and burns hotter.

4. Do not attempt to burn (or mix in) green or wet wood. The use of green or wet wood will cause a rapid build

up of creosote. Wood that hisses, sizzles and blackens without igniting in ve minutes must be considered too

wet to burn.

5. Do not attempt to extend the burn time by using wet wood. Not only does burning wet wood rapidly build

up creosote, but it reduces the heat output by up to 25 percent.

6. Burn the stove with the primary air inlet control wide open (pushed in) for 10-25 minutes every time fresh

wood is loaded into the stove. Do not load more than ¼ to ½ of the fuel capacity at one time. Loading too

much wood at once will cause excessive smoke which contains creosote. Mature res or coals produce very

little creosote-producing smoke.

7. Burn with the primary air control open (pushed in) for several minutes at numerous intervals throughout the

day, being careful not to over re the unit. Following this process will help to warm the chimney and reduce

the amount of creosote forming condensation within the chimney.

8. Establish a routine for the handling of fuel, ring, and operating the stove. Check daily for creosote build up

until experience shows how often you need to clean for safe operation. Be aware that the hotter the re,

the less creosote is deposited and weekly cleaning may be necessary in mild weather even though monthly

cleaning may be enough in the colder months.

SMOKE AND CO MONITORS

Burning wood naturally produces smoke and carbon monoxide (CO) emissions. CO is a poisonous gas when

exposed to elevated concentrations for extended periods of time. While the modern combustion systems in

heaters drastically reduce the amount of CO emitted out the chimney, exposure to the gases in closed or conned

areas can be dangerous. Make sure your stove gaskets and chimney joints are in good working order and sealing

properly to ensure unintended exposure. It is recommended that you use both smoke and CO monitors in areas

having the potential to generate CO.

GLASS CARE

Periodic cleaning of glass will be necessary to prevent accumulations of ash. Acidic ash buildup can eventually

etch and weaken glass. Creosote accumulations should burn off during hot res. The following usage and safety

tips should be observed:

1. Inspect the glass regularly for cracks and breaks. If you detect a crack or break, extinguish the re immediately

and contact the manufacturer for a replacement before re-ring the stove.

2. Do not slam the door or otherwise impact the glass. When closing doors, make sure that logs or other objects

do not protrude to impact the glass.

3. Do not build res against (or that might fall against) the glass.

4. Do not clean the glass with materials that may scratch (or otherwise damage) the glass. Scratches on the

glass can develop into cracks or breaks during operation.

5. Never attempt to clean the glass while the unit is hot; allow to dry thoroughly before reuse. If deposits are not

very heavy, normal glass cleaners are adequate using a soft, non-abrasive cleaning pad.

6. Never put substances which can ignite explosively in the unit. Even small explosions in conned areas can

blow out the glass.

GLASS REPLACEMENT

Gasket and Glass cleaning products are available at local retail home centers. Manufacturers of cleaning

products include, A.W. Perkins Co. (www.awperkins. com) or Rutland Products (www.rutland.com). After extensive

use, the gasket material which provides glass and door seal may lose it’s resiliency and will need to be replaced.

Inspect glass and door gaskets periodically to ensure proper seal; if gaskets become frayed or worn, replace

immediately.

This wood heater needs periodic inspection and repair for proper operation. It is against federal regulations

to operate this wood heater in a manner inconsistent with operating instructions in this manual.

La page charge ...

United States Stove TR007 Le manuel du propriétaire

Marque: United States Stove

Modèle: TR007

Catégorie: Poêles

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: United States Stove TR007 Owner's manual

United States Stove TR007 Le manuel du propriétaire

United States Stove TR007 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents