United States Stove 1269E Le manuel du propriétaire

Marque: United States Stove

Modèle: 1269E

Catégorie: Poêle à bois

Taper: Le manuel du propriétaire

852430F-1203H

Owner’s Operation and Instruction Manual

SAFETY NOTICE:

If this heater is not properly installed, a house

re may result. For your safety, follow the

installation instructions. Never use make-shift

compromises during the installation of this

heater. Contact local building or re ofcials

about permits, restrictions and installation

requirements in your area.

CAUTION!

Please read this entire manual before you

install or use your new room heater. Failure

to follow instructions may result in property

damage, bodily injury, or even death.

Improper Installation Could Void

Your Warranty!

U.S. Environmental Protection Agency

Certied to comply with 2015 particulate

emission standards for single burn rate

heaters. Not approved for sale after May 15,

2020. This single burn rate wood heater is not

approved for use with a ue damper.

Certied To: UL 1482 and ULC 627

United States Stove Company

227 Industrial Park Road

South Pittsburg, TN 37380

DO NOT USE THIS HEATER IN A MOBILE HOME. SAVE THESE INSTRUCTIONS

THIS MANUAL WILL HELP YOU TO OBTAIN EFFICIENT, DEPENDABLE SERVICE FROM THE HEATER, AND ENABLE YOU

TO ORDER REPAIR PARTS CORRECTLY. KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

MODEL: 1269E Log Wood

CALIFORNIA PROPOSITION 65 WARNING:

This product can expose you to chemicals including carbon monoxide, which

is known to the State of California to cause cancer, birth defects and/or other

reproductive harm. For more information, go to www.P65warnings.ca.gov

Ce produit peut vous exposer à des produits chimiques, y compris le

monoxyde de carbone, qui est connu dans l'État de Californie pour causer

le cancer, des malformations congénitales et / ou d'autres problèmes de

reproduction. Pour plus d'informations, visitez www.P65warnings.ca.gov

-2-

This manual describes the installation and operation of the United States Stove

Company Model 1269E woodheater. This heater meets the 2015 U.S. Environmental

Protection Agency's crib wood emission limits for woodheaters sold after May 15, 2015.

Under specic EPA test conditions burning Douglas Fir dimensional lumber this heater

has been shown to deliver heat at a rate of 24,433 Btu/hr. This heater achieved a

particulate emissions rate of 4.2 g/hr when tested to method ASTM E2780-10 single Burn

Rate Appendix (*and an efciency of 67.9 %.)

This wood heater has a manufacturer-set minimum low burn rate that must not be altered. It is against federal

regulations to alter this setting or otherwise operate this wood heater in a manner inconsistent with operating

instructions in this manual.

The operation of this wood heater in a manner inconsistent with the owner’s manual will void you warranty and

is also against federal regulations.

This heater is designed to burn natural wood only. Higher efciencies and lower emissions generally result when

burning air dried seasoned hardwoods, as compared to softwoods or to green or freshly cut hardwoods. Burning

the following materials may result in release of toxic fumes or render the heater ineffective and cause smoke.

This wood heater needs periodic inspection and repair for proper operation. It is against federal regulations to

operate this wood heater in a manner inconsistent with operating instructions in this manual.

CONGRATULATIONS!

You’ve purchased a heater from North America’s oldest manufacturer of wood burning products.

By heating with wood you’re helping to CONSERVE ENERGY!

Wood is our only Renewable Energy Resource. Please do your part to preserve our wood supply. Plant at least

one tree each year. Future generations will thank you.

The instructions pertaining to the installation of your wood stove comply with UL & ULC standards.

Combustible: Wood

Colors: Flat Black

Flue Pipe Diameter: 6” (15.3cm)

Flue Pipe Type: (Standard Single Wall or Double Wall): Black or Blued Steel 2100°F (650°C)

Minimum Chimney Height: 12’ (3.7m)

Maximum Log Length: 22” (559mm)

Electrical: None

Dimensions

Overall ( Depth x Width x Height ): 33” x 18.5” x 23” (838mmX470mmX854mm)

Combustion Chamber: Width x Depth: 19” x 9” (482mmX229mm)

Volume: Cubic Feet: 1.2 cubic feet

Door Opening: 7.5 x 10.2 (191mmX259mm)

Pyroceramic Glass Door : (Viewing) Width x Height: N/A

Weight (lbs): 140 lbs

Report No. 0215WS038E

Note: Register your product on line at www.usstove.com. Save your receipt with your records for any claims.

-3-

33"

4-5/8"

23"

FLOOR PROTECTOR

11-3/8"

18-1/2"

26-1/2"

DO NOT BURN:

1. Residential or commercial garbage;

2. Lawn clippings or yard waste;

3. Materials containing rubber, including tires;

4. Materials containing plastic;

5. Waste petroleum products, paints or paint thinners, or asphalt products;

6. Materials containing asbestos;

7. Construction or demolition debris;

8. Paper products, cardboard, plywood, or particleboard. The prohibition against burning these materials does

not prohibit the use of re starters made from paper, cardboard, saw dust, wax and similar substances for the

purpose of starting a re in unaffected wood heater.

9. Railroad ties or pressure-treated wood;

10. Manure or animal remains;

11. Salt water driftwood or other previously salt water saturated materials;

12. Unseasoned wood;

13. Any materials that are not included in the warranty and owner’s manual for the subject wood heater; or

14. Any materials that were not included in the certication tests for the subject wood heater.

Do not burn manufactured logs made of wax impregnated sawdust or logs with any

chemical additives. Manufactured logs made of 100% compressed sawdust can be

burned, but be careful burning too much of these logs at the same time. Start with one

manufactured log and see how the stove reacts. You can increase the number of logs

burned at a time to making sure the temperature never rises higher than 475 °F (246 °C)

on a magnetic thermometer for installation on single wall stove pipes or 900 °F (482 °C)

on a probe thermometer for installation on double wall stove pipe. The thermometer

should be placed about 18” (457 mm) above the stove. Higher temperatures can lead

to overheat and damage your stove.

Tools and Materials Needed

TOOLS

• Pencil

• 6 Foot Folding Ruler or Tape Measure

• Tin Snips

• Drill, Hand or Electric

• Drill Bit 1/8" Dia. (For Sheet Metal Screws)

• Adjustable Wrench

• Screw Driver (Blade-Type)

• Gloves

• Safety Glasses

MATERIALS

• 6" Elbow, Collar and Thimble; As Required (24 gauge

min.)

• 1/2" Sheet Metal Screws (No. 10A x 1/2")

• 6" Diameter, 24 gauge, black or blued steel ue

connector pipe

• Floor Protector Material (R value = 2.06); Size and

Installation as specied in this manual

• Furnace Cement (Manufacturer Recommends:

Rutland Black Code 78 or Equivalent)

• Optional; 6" Barometric Draft Regulator (DR-6)

HEATER DIMENSIONS FIG. 1

-4-

Operational Tips

BUILDING A FIRE

The top down method of re building is recommended for this appliance. Place the largest pieces of wood on

the bottom, laid in parallel and close together. Smaller pieces are placed in a second layer, crossways to the

rst. A third layer of still smaller pieces is laid crossways to the second, this time with some spaces between. Then

a fourth layer of loose, small kindling and twisted newspaper sheets tops off the pile.

VISIBLE SMOKE

Visible smoke is basically unburned fuel and moisture leaving your stove. The amount of visible smoke being

produced can be an effective method of determining how efciently the combustion process is taking place at

the given settings. Learn to adjust the air settings of your specic unit to produce the smallest amount of visible

smoke. Remember that wood that has not been seasoned properly and has a high wood moisture content will

produce excess visible smoke and burn poorly.

ASH REMOVAL AND DISPOSAL

Whenever ashes get 3 to 4 inches deep in your rebox or ash pan, and when the re has burned down and

cooled, remove excess ashes. Leave an ash bed approximately 1 inch deep on the rebox bottom to help

maintain a hot charcoal bed.

Ashes should be placed in a metal container with a tight-tting lid. The closed container of ashes should be

placed on a noncombustible oor or on the ground, away from all combustible materials, pending nal disposal.

The ashes should be retained in the closed container until all cinders have thoroughly cooled.

AIR TUBES

The air tubes assembled in this unit are designed to provide an accurate mix of secondary air to insure the

highest efciency. Any damage or deterioration of these tubes may reduce the efciency of combustion. The

air tubes are held in position by either screws or snap pins. Locate these to either side of the tube and remove to

allow the tube to be removed and replaced.

OVER FIRING

Attempts to achieve heat output rates that exceed heater design specications can result in permanent

damage to the heater and to the catalytic combustor if so equipped.

IMPORTANCE OF PROPER DRAFT

Draft is the force which moves air from the appliance up through the chimney. The amount of draft in your

chimney depends on the length of the chimney, local geography, nearby obstructions and other factors. Too

much draft may cause excessive temperatures in the appliance and may damage the catalytic combustor

(if equipped). Inadequate draft may cause backpufng into the room and ‘plugging’ of the chimney or the

catalyst (if equipped). Inadequate draft will cause the appliance to leak smoke into the room through appliance

and chimney connector joints. An uncontrollable burn or excessive temperature indicates excessive draft.

CHIMNEY

Take into account the chimney’s location to insure it is not too close to neighbors or in a valley which may cause

unhealthy or nuisance conditions.

-5-

EFFICIENCY

Efciencies can be based on either the lower heating value (LHV) or the higher heating value (HHV) of the fuel.

The lower heating value is when water leaves the combustion process as a vapor, in the case of woodstoves the

moisture in the wood being burned leaves the stove as a vapor. The higher heating value is when water leaves

the combustion process completely condensed. In the case of woodstoves this would assume the exhaust gases

are room temperature when leaving the system, and therefore calculations using this heating value consider

the heat going up the chimney as lost energy. Therefore, efciency calculated using the lower heating value of

wood will be higher than efciency calculated using the higher heating value. In the United States all woodstove

efciencies should be calculated using the higher heating value.

As an operator of a wood heater the best way to achieve optimum efciencies is to learn the burn characteristic

of you appliance and burn well-seasoned wood. A good rule of thumb is that your heater is not producing or

producing very little visible smoke it is burning efciently. Also remember that higher burn rates are not always

the best heating burn rates; after a good re is established a lower burn rate may be a better option for efcient

heating. A lower burn rate slows the ow of usable heat out of the home through the chimney, and it also

consumes less wood.

SMOKE AND CO MONITORS

Burning wood naturally produces smoke and carbon monoxide(CO) emissions. CO is a poisonous gas when

exposed to elevated concentrations for extended periods of time. While the modern combustion systems in

heaters drastically reduce the amount of CO emitted out the chimney, exposure to the gases in closed or

conned areas can be dangerous. Also make sure you stove gaskets and chimney joints are in good working

order and sealing properly to ensure unintended exposure. It is recommended that you use both smoke and CO

monitors in areas expected to or having the potential to generate CO.

OPERATIONAL TIPS FOR GOOD, EFFICIENT, AND CLEAN COMBUSTION

Use smaller pieces of wood during start-up and a high burn rate to increase the stove temperature

Be considerate of the environment and only burn dry wood

Burn small, intense res instead of large, slow burning res when possible

Learn your appliance's operating characteristics to obtain optimum performance

Burning unseasoned wet wood only hurts your stoves efciency and leads to accelerated creosote buildup in

your chimney

WOOD SELECTION TIPS

Dead wood lying on the forest oor should be considered wet, and requires full seasoning time. Standing dead

wood can usually be considered to be about 2/3 seasoned. Splitting and stacking wood before it is stored

accelerates drying time. Storing wood on an elevated surface from the ground and under a cover or covered

area from rain or snow also accelerates drying time. A good indicator if wood is ready to burn is to check the

piece ends. If there are cracks radiating in all directions from the center then the wood should be dry enough

to burn. If your wood sizzles in the re, even though the surface is dry, it may not be fully cured, and should be

seasoned longer.

-6-

Safety Rules

NOTE: FOR YOUR SAFETY, WE RECOMMEND INSTALLING SMOKE DETECTORS IN YOUR HOME IF NOT ALREADY

INSTALLED.

CAUTION! Do not touch the heater until it has cooled.

SAFETY NOTICE: If this heater is not properly installed, a house re may result. For your safety, follow the

installation directions. Contact local building or re ofcials about restrictions and installation inspection

requirements in your area.

READ THESE RULES AND THE INSTRUCTIONS CAREFULLY

1. Check with local codes. The installation must

comply with their rulings. Observe closely the

clearances to combustibles.

2. Do not install this heater in a mobile home or trailer.

3. Always connect this heater to a chimney and

vent to the outside. Never vent to another room or

inside a building. DO NOT CONNECT THIS UNIT TO A

CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

4. Do not connect a wood burning heater to a Type

B gas vent. This is not safe and is prohibited by

the National Fire Protection Association Code.

This heater requires approved masonry or UL,

ULC Listed Residential Type and Building Heating

Appliance Chimney. Use a 6" diameter chimney,

or larger, that is high enough to give a good draft.

5. Be sure that your chimney is safely constructed and

in good repair. Have the chimney inspected by

the Fire Department or a qualied inspector. Your

insurance company may be able to recommend

a qualied inspector.

6. Inspect chimney connector and chimney twice

monthly during the heating season for any deposit

of creosote or soot which must be removed (see

Chimney Maintenance).

7. Provide air for combustion from outside the house

into the room where the heater is located. If the

intake is not in the same room, air must have free

access in to the room.

8. To prevent injury, do not allow anyone to use this

heater who is unfamiliar with the correct operation

of the heater.

9. For further information on using your heater safely,

obtain a copy of the National Fire Protection

Association (NFPA) publication "Using Coal and

Wood Stoves Safely" NFPA No. HS-10-1978. The

address of the NFPA is Batterymarch Park, MA

02269.

• For more information on a Canadian

Installation, obtain a copy of CAN/CSA - B365

- M91 Installation Code for Solid-Fuel-Burning

Appliances and Equipment.

10. Disposal of Ashes - Ashes should be placed in

a metal container with a tight tting lid. The

closed container of ashes should be placed on a

noncombustible oor or on the found, well away

from all combustible materials, pending nal

disposal. If the ashes are disposed of by burial in

soil or otherwise locally dispersed, they should be

retained in the closed container until all cinders

have thoroughly cooled.

11. CAUTION - The special paints used on your heater

may give off some smoke while they are curing

during the rst few res. Build small res at rst.

Children and people/animals with lung problems

should take caution during the curing process.

12. CARING FOR PAINTED PARTS - This heater has

a painted jacket which is durable but it will not

stand rough handling or abuse. When installing

your heater, use care in handling. Clean with soap

and warm water when heater is not hot. DO NOT

use any acids or scouring soap, as these wear and

dull the nish. PAINT DISCOLORATION WILL OCCUR

IF THE HEATER IS OVERFIRED. FOLLOW OPERATING

INSTRUCTIONS CAREFULLY.

13. All persons, especially children, should be alerted

to hazards from high surface temperatures and

kept away while in operation. Small children

should not be left unsupervised when in the room

with the heater.

14. Keep the area adjacent to the heater free from

all combustible materials, gasoline, and other

ammable vapors.

15. This heater should not be used as a primary source

of heat.

-7-

NOTICE: United States Stove Company grants no warranty, stated or implied, for the installation or maintenance

of your wood stove and assumes no responsibility of any incidental or consequential damages.

ASSEMBLY INSTRUCTIONS

1. Uncrate the stove and remove packing materials and protective poly bag. (save cardboard box for further

assembly.)

2. Remove parts from inside of stove. Parts include: one feed door, four legs, hardware pack, ue collar, hearth

plate, and bottom air channel.

3. Place attened carton on oor and carefully turn stove over onto carton.

4. Attach bottom air channel with four (4) 1/4-20 X 3/8" screw, and four (4) washers.

5. Attach hearth to bottom of stove with two (2) 1/4-20 x 1-3/16 screws, two (2) washers, and two (2) 1/4-20 jam

nuts.

REQUIRED TOOLS

• Safety Glasses

• Hearth Gloves

• Pencil

• 6' Folding Ruler or Tape Measure

• Tin Snips

• Drill

• 1/8" dia. Drill Bit

• Adjustable Wrench

• (Sheet Metal Screws)

• #2 philips screw driver

REQUIRED MATERIALS

• Note: the following items are not included with your

stove

• Flooring protector as specied

• Chimney Connector

• 1/2" Sheet Metal Screws

• Chimney

• Furnace Cement

CAUTION: Stove is heavy. Make sure you have adequate help and use proper lifting techniques whenever

moving stove.

-8-

6. Attach the front legs to hearth with two (2) 1/4-20 x 1-3/4 screws, two (2) at washers, and two (2) 1/4-20

jam nuts.

7. Attach the rear legs to base of stove with two (2) 1/4-20 x 1-3/4 screws, two (2) at washers, and two (2) 1/4-

20 jam nuts.

8. Carefully lift stove upright and place in desired location. Align the holes on the ue collar to the holes on the

stove and attach using (2) two 1/4-20 X 1-3/4 screws.

9. Lower feed door into position while aligning hinge pins.

KEY PART NO. DESCRIPTION QTY.

1 83658 1/4-20 X 1-3/16 Flathead Phillips Screw 4

2 83563 1/4-20 X 3/4 Flt Hd Ph Mach 4

3 83659 1/4-20 X 1-3/4 Flt Hd Ph Screw 4

4 83336 1/4-20 Jam Nut 10

5 83278 7/32 Id X 1/2 Od X 3/64 Fl W 10

-9-

Installation

MINIMUM CLEARANCE TO COMBUSTIBLE WALLS US, CANADA

HEATER/FLOOR PROTECTOR LOCATION (Dimensions are required for

non-protected surfaces. See chart for dimensions for protected surfaces.)

Place the heater on solid masonry or solid concrete. When the heater

is used on a combustible oor, use an Underwriters Listed oor protector.

The oor protector must comply with UL Standards (USA) and CAN/ULC

(Canada) and have an R-value of 2.06. The oor protector needs to

extend at least 16" beyond the door side of the heater and 8" to each side.

It should also extend 8" beyond the rear for Canada. The oor protector

needs to extend 2" beyond each side of the ue pipe if it is elbowed

towards a wall as well as 2" on each side of the ue for horizontal runs.

1. After consulting the installation instructions for minimum clearances

to combustibles, locate your oor protector accordingly and

carefully place the stove in your selected location. Install stove pipe,

elbows and thimble as necessary, utilizing either a recently cleaned

and inspected masonry chimney (properly lined) or a UL, ULC Listed

chimney. Insure that the xed ue bafe that is provided is installed

in the ue collar. This bafe is intended to be in a xed location for

optimal combustion. Do not remove or alter the location of this

bafe. It is against federal regulations and will void your warranty.

2. Again, check the following illustrations and be sure you have the

clearances shown from the heater and the connector pipe to

combustible surfaces. If you have a solid brick or stone wall behind

your heater, please consult your local building code for specic

regulations that may apply in your area. However, if the wall is only

faced with brick or stone, consider it a combustible wall. To reduce

ue clearances from combustible materials, contact your local

safety department.

3. If your chimney drafts excessively, purchase and use a Barometric

Draft Regulator (DR6 available from factory).

4. The chimney connection should be as short as possible, and the

heater must have its own ue. Do not connect this unit to a chimney

ue serving other appliances.

5. Use three sheet metal screws in each stove pipe and or elbow joint

to rmly hold the pipe together. Seal around the screws

6. Do not install this heater in a mobile home or trailer.

7. Check your local building and insurance codes. The installation must

comply with their rulings.

419mm

18”

419mm

18”

8”

203mm

CAUTION!

Keep furnishings and other combustible materials

away from the heater.

Non-Combustible Construction In Accordance With Nfpa 211

8”

203mm

-10-

Operation Of The Heater

1. Burn wood or wood products only. The wood should be well seasons prior to use for maximum efciency.

2. Provide air into the room for combustion.

3. Do Not touch the heater after ring until it has cooled.

4. Do Not use a grate or elevate re, build re directly on hearth. The fuel feed door must remain closed during

operation.

MASONRY CHIMNEY

The masonry chimney must comply with UL, ULC codes.

Before using an existing masonry chimney, clean the chimney

and inspect the ue liner to be sure it is safe to use. Make

repairs before attaching the heater. See Page 3, Item 5.

Look at Fig. 5. The connector pipe and ttings you will need

to connect directly to a masonry chimney are shown. If the

connector pipe must go through a combustible wall before

entering the masonry chimney, consult a qualied mason or

chimney dealer. The installation must conform to local re

codes, and NFPA 211(USA) or CAN/CSA-B365-M91(CANADA).

Do not connect this heater into the same chimney ue as the

replace or ue from another heater. The chimney used for a

heater must not be used to ventilate the cellar or basement. If

there is a cleanout opening at the base of the chimney, close

it tightly.

UL/ULC LISTED CHIMNEY

Carefully follow chimney manufacturer's instructions. Use only

listed type HT per UL, ULC 103, 6-in diameter black or blued

chimney connector, minimum 24 gauge steel. If your chimney

starts at the ceiling (Fig. 6), you will need enough 6" pipe to

reach the ceiling.

The top of the chimney must be at least 3 feet above the roof

and be at least 2 feet higher than any point of the roof within

10 feet. (Fig 6). Use double or triple wall pipe for the exterior

portion of the chimney.

RULES FOR CONNECTOR PIPE INSTALLATION

1. Crimped end of the pipe must be installed toward the

heater. The pipe should slide into the ue collar. The pipe

should be rmly attached to the ue collar with 3 screws

and sealed with furnace cement.

2. Slope any horizontal pipe upward toward the chimney

at least 1/4 inch for each foot of horizontal run. Horizontal

section must be a minimum of 24" from stove.

3. You must have at least 18" inches clearance between

any horizontal piping and the ceiling.

4. The pipe cannot extend into the chimney ue.(Fig. 7)

5. Seal each connector pipe joint with furnace cement.

Also, seal the pipe at the chimney. Seal the inside with

high temperature silicone and the outside with high

temperature tape.

6. Use 3 sheet metal screws at each joint to make the piping

rigid.

FIG. 5

ELBOW

COLLAR

THIMBLE

FLOOR PROTECTOR

FLUE CONNECTION-NON-COMBUSTIBLE WALL

PIPE

NONCOMBUSTIBLE WALL

PIPE

BAROMETRIC

DRAFT REGULATOR

WRONG

RIGHT

FIG. 6

FIG. 5

ELBOW

COLLAR

THIMBLE

PIPE REDUCER

FLOOR PROTECTOR

3 FT. MIN.

2 FT. MIN

10 FT.

CHIMNEY CAP MANDATORY

11 FT. MINIMUM

FIG. 7

WRONG

FLUE CONNECTION-NON-COMBUSTIBLE WALL

PIPE

NONCOMBUSTIBLE WALL

PIPE

BAROMETRIC

DRAFT REGULATOR

BAROMETRIC

DRAFT REGULATOR

PIPE

NONCOMBUSTIBLE

CONSTRUCTION IN

ACCORDANCE WITH

NFPA 211

Chimney Connection

-11-

7. It is recommended that no more than two (2) 90 degree bends be used in the stove pipe installation as more

than two (2) may decrease the amount of draw and possibly cause smoke spillage.

NOTE: The chimney connector shall not pass through an attic, roof space, oor, ceiling, or similar concealed

space. Where passage through a wall or partition of combustible construction is desired, the installation must

conform with CAN/CSA - B365.

WRONG

RIGHT

FIG. 6

FIG. 5

ELBOW

COLLAR

THIMBLE

PIPE REDUCER

FLOOR PROTECTOR

3 FT. MIN.

2 FT. MIN

10 FT.

CHIMNEY CAP MANDATORY

11 FT. MINIMUM

FIG. 7

WRONG

FLUE CONNECTION-NON-COMBUSTIBLE WALL

PIPE

NONCOMBUSTIBLE WALL

PIPE

BAROMETRIC

DRAFT REGULATOR

BAROMETRIC

DRAFT REGULATOR

PIPE

NONCOMBUSTIBLE

CONSTRUCTION IN

ACCORDANCE WITH

NFPA 211

CONNECTION OF CHIMNEY CONNECTOR TO A MASONRY CHIMNEY THROUGH A COMBUSTIBLE WALL

Figure 8 shows how to connect the chimney connector of a heater to a masonry chimney through a combustible

wall. There are ve allowable ways that a chimney connector can be connected to a masonry chimney by

passing through a combustible wall. NFPA Standard 211 allows the following wall pass-through systems.

CONNECTION OF CHIMNEY CONNECTOR TO A MASONRY CHIMNEY THROUGH A COMBUSTIBLE WALL

Figure 8 shows how to connect the chimney connector of a heater to a masonry chimney through a combustible wall.

There are five allowable ways that a chimney connector can be connected to a masonry chimney by passing through

a combustible wall. NFPA Standard 211 allows the following wall pass-through systems.

MASONRY CHIMNEY

CONSTRUCTED TO

NFPA 211

AIRTIGHT

CLEANOUT

DOOR

FLOOR

PROTECTOR

COMBUSTIBLE WALL

HEATER

CHIMNEY CONNECTOR

CEILING

SEE PARTS A, B,

C, D, AND E OF

THIS FIGURE FOR

OPTIONS.

CHIMNEY FLUE

FIGURE 8 -

CONNECTION OF CHIMNEY CONNECTOR TO A

MASONRY CHIMNEY THROUGH A COMBUSTIBLE

WALL

(FIGURE 8 CONTINUED ON NEXT PAGE)

-12-

MINIMUM 12 IN.

TO COMBUSTIBLES

PART A, FIGURE 8

(FIGURE 8 CONTINUED ON NEXT PAGE)

1. Use a minimum 3-1/2" thick brick masonry wall framed into the combustible wall. A fireclay liner (ASTM C315 or

equivalent) having a 5/8" minimum wall thickness must be used and it must be at least 12" away from any material

that could catch fire. The inside diameter of the fireclay liner shall be sized for the proper snug fit of a 6" diameter

chimney connector pipe. The fireclay liner shall run from the outer surface of the brick wall to, but not beyond, the

inner surface of the chimney flue and shall be firmly cemented in place. See Part A of Figure 8.

2. Use a solid insulated listed factory-built chimney length having an inside diameter of 6" and having 1" or more of

solid insulation. There must be at least a 9" air space between the outer wall of the chimney length and any

combustible materials. The inner end of the chimney length shall be flush with the inside of the masonry chimney , the

flue shall be sealed to the flue and to the brick masonry penetration with nonwater-soluble refractory cement. Sheet

steel supports which are at least 24 gauge(0.024") in thickness shall be securely fastened to wall

surfaces on all sides. Fasteners between supports and the chimney length shall not penetrate the chimney liner.

See Part B of Figure 8.

3. Use a 10" diameter ventilated thimble made of at least 24 gauge(0.024") steel having two 1" air channels. The venti-

lated thimble must be separated from combustible materials by a minimum of 6" glass fiber insulation. The opening

in the combustible wall shall be covered and the thimble supported with sheet steel supports which are at least 24

gauge (0.024") in thickness. The sheet steel supports shall be securely fastened to wall surfaces on all sides and

shall be sized to fit and hold the chimney section. Fasteners used to secure chimney sections shall not penetrate

chimney flue liner. See Part C of Figure 8.

4. Use an 8" inside diameter solid insulated listed factory-built chimney length which has 1" or more of solid insulation.

The minimum length of this chimney section shall be 12" and will serve as a pass-through for the 6" diameter

chimney connector. There must be at least a 12" air space between the outer wall of the chimney section and any

combustible materials. The chimney section shall be concentric with and spaced 1" away from the chimney connec

tor by means of sheet steel support plates on both ends of the chimney section. The opening in the combustible wall

shall be covered and the chimney section supported on both sides with sheet steel supports which are at least 24

gauge (0.024") in thickness. The sheet steel supports shall be securely fastened to wall surfaces on all sides and

shall be sized to fit and hold the chimney section. Fasteners used to secure chimney sections shall not penetrate

chimney flue liner. See Part C of Figure 8.

5. A listed factory-built wall pass-through system may be purchased and installed according to the instructions pack

aged with it to provide a safe method of passing the chimney connector through a combustible wall for connection

to a masonry chimney.

Additional requirements pertaining to Figure 8 and the above wall pass-through systems:

1. Insulation material used as part of wall pass-through system shall be of noncombustible material and shall have a

thermal conductivity of 1.0 Btu • in./ft.² • °F (4.88 kg • cal/hr • m² • °C) or less

2. All clearances and thicknesses are minimums: larger clearances and thickness are acceptable.

3. A chimney thimble, as shown for 3" and 4" above (Parts C and D respectively of Figure 8) shall be for types "3" and

4" connections to facilitate removal of the chimney connector for cleaning. The chimney thimble shall be of ASTM

C315 fireclay with 5/8" minimum wall thickness, or material of equivalent durability. The inside diameter of the

thimble shall be sized for the proper snug fit of a 6" diameter chimney connector pipe. The thimble shall be installed

without damage to the chimney flue. The thimble shall extend through the chimney wall to, but not beyond, the

inner surface of the chimney flue and shall be permanently cemented in place with high temperature cement.

4. A chimney connector to a masonry chimney, except for 2" above (Part B of Figure 8), shall extend through the wall

pass-through system to the inner face of the chimney flue, but not beyond. It does not have to be fastened in place

so long as it cannot accidently be pulled out of the chimney or shoved into the chimney flue. If fasteners are used

to secure the chimney connector to a masonry chimney, the fasteners shall not penetrate the chimney flue liner.

5. Any material used to close up any opening for the connector shall be noncombustible.

CHIMNEY FLUE

MINIMUM CHIMNEY CLEARANCE TO

BRICK AND COMBUSTIBLES IS 2 IN.

MINIMUM CLEARANCES 12 IN.

OF BRICK ALL AROUND

CHIMNEY CONNECTOR

TO HEATER

FIRE CLAY LINER

(5/8" MIN. WALL THICKNESS)

MIN. 3-1/2" THICK BRICK

MASONRY WALL

MASONRY CHIMNEY

CONSTRUCTED TO

NFPA 211

1. Use a minimum 3-1/2" thick brick masonry wall framed into the combustible wall. A reclay liner (ASTM C315

or equivalent) having a 5/8" minimum wall thickness must be used and it must be at least 12" away from any

material that could catch re. The inside diameter of the reclay liner shall be sized for the proper snug t of

a 6" diameter chimney connector pipe. The reclay liner shall run from the outer surface of the brick wall to,

but not beyond, the inner surface of the chimney ue and shall be rmly cemented in place. See Part A of

Figure 8.

2. Use a solid insulated listed factory-built chimney length having an inside diameter of 6" and having 1" or

more of solid insulation. There must be at least a 9" air space between the outer wall of the chimney length

and any combustible materials. The inner end of the chimney length shall be ush with the inside of the

masonry chimney , the ue shall be sealed to the ue and to the brick masonry penetration with nonwater-

soluble refractory cement. Sheet steel supports which are at least 24 gauge(0.024") in thickness shall be

securely fastened to wall surfaces on all sides. Fasteners between supports and the chimney length shall not

penetrate the chimney liner. See Part B of Figure 8.

3. Use a 10" diameter ventilated thimble made of at least 24 gauge(0.024") steel having two 1" air channels. The

ventilated thimble must be separated from combustible materials by a minimum of 6" glass ber insulation.

The opening in the combustible wall shall be covered and the thimble supported with sheet steel supports

which are at least 24 gauge (0.024") in thickness. The sheet steel supports shall be securely fastened to wall

surfaces on all sides and shall be sized to t and hold the chimney section. Fasteners used to secure chimney

sections shall not penetrate chimney ue liner. See Part C of Figure 8.

4. Use an 8" inside diameter solid insulated listed factory-built chimney length which has 1" or more of solid

insulation. The minimum length of this chimney section shall be 12" and will serve as a pass-through for the 6"

diameter chimney connector. There must be at least a 12" air space between the outer wall of the chimney

section and any combustible materials. The chimney section shall be concentric with and spaced 1" away

from the chimney connector by means of sheet steel support plates on both ends of the chimney section.

The opening in the combustible wall shall be covered and the chimney section supported on both sides

with sheet steel supports which are at least 24 gauge (0.024") in thickness. The sheet steel supports shall be

securely fastened to wall surfaces on all sides and shall be sized to t and hold the chimney section. Fasteners

used to secure chimney sections shall not penetrate chimney ue liner. See Part C of Figure 8.

5. A listed factory-built wall pass-through system may be purchased and installed according to the instructions

pack aged with it to provide a safe method of passing the chimney connector through a combustible wall

for connection to a masonry chimney.

ADDITIONAL REQUIREMENTS PERTAINING TO FIGURE 8 AND THE ABOVE WALL PASS-THROUGH SYSTEMS

1. Insulation material used as part of wall pass-through system shall be of noncombustible material and shall

have a thermal conductivity of 1.0 Btu • in./ft.² • °F (4.88 kg • cal/hr • m² • °C) or less

2. All clearances and thicknesses are minimums: larger clearances and thickness are acceptable.

3. A chimney thimble, as shown for 3" and 4" above (Parts C and D respectively of Figure 8) shall be for types "3"

and 4" connections to facilitate removal of the chimney connector for cleaning. The chimney thimble shall

be of ASTM C315 reclay with 5/8" minimum wall thickness, or material of equivalent durability. The inside

diameter of the thimble shall be sized for the proper snug t of a 6" diameter chimney connector pipe. The

thimble shall be installed without damage to the chimney ue. The thimble shall extend through the chimney

wall to, but not beyond, the inner surface of the chimney ue and shall be permanently cemented in place

with high temperature cement.

-13-

CONNECTION OF CHIMNEY CONNECTOR TO A MASONRY CHIMNEY WHEN CHIMNEY CONNECTOR

DOES NOT PASS THROUGH A COMBUSTIBLE WALL

PART E - (FIGURE 8)

In addition to the methods shown by A, B, C, and D of Figure 8, a listed factory-built wall pass-through system

may be purchased and installed according to the instructions packaged with it to provide a safe method of

passing chimney connector through a combustible wall for a connection to a masonry chimney.

If the chimney connector does not have to pass through a combustible wall to get to a masonry chimney, simply

connect the chimney connector directly to the masonry chimney's chimney thimble as described and shown

by parts C and D of Figure 8. Remember, the chimney connector should extend into the chimney thimble to

the inner face of the chimney ue but not beyond; if the chimney connector is extended through the chimney

thimble into the chimney ue, resistance to the ow of smoke and gases up the chimney will occur; that ow

resistance will have an adverse affect on the operation and performance of the heater and venting system.

CONNECTION OF CHIMNEY CONNECTOR TO A MASONRY CHIMNEY WHEN CHIMNEY CONNECTOR

DOES NOT PASS THROUGH A COMBUSTIBLE WALL

PART E - (Figure 8)

In addition to the methods shown by A, B, C, and D of Figure 8, a listed factory-built wall pass-through system

may be purchased and installed according to the instructions packaged with it to provide a safe method of

passing chimney connector through a combustible wall for a connection to a masonry chimney.

If the chimney connector does not have to pass through a combustible wall to get to a masonry chimney, simply connect

the chimney connector directly to the masonry chimney's chimney thimble as described and shown by parts C and D of

Figure 8. Remember, the chimney connector should extend into the chimney thimble to the innerface of the chimney flue

but not beyond; if the chimney connector is extended through the chimney thimble into the chimney flue, resistance to the

flow of smoke and gases up the chimney will occur; that flow resistance will have an adverse affect on the operation and

performance of the heater and venting system.

PART B

FIGURE 8 -

(FIGURE 8 CONTINUED)

AIR SPACE

9 IN. MINIMUM

FACTORY-BUILT

CHIMNEY LENGTH

SHEET STEEL SUPPORTS

CHIMNEY SECTION

CHIMNEY

CONNECTOR

AIR SPACE

2 IN.

TWO VENTILATED AIR

CHANNELS EACH 1 INCH.

CONSTRUCTED OF

SHEET STEEL.

PART C

FIGURE 8

PART D

FIGURE 8

MASONRY CHIMNEY CONSTRUCTED

TO NFPA 211

SHEET STEEL SUPPORTS

(24 GAUGE MIN. THICKNESS)

CHIMNEY CONNECTOR

TO HEATER

MINIMUM CHIMNEY CLEARANCES FROM MASONRY TO

SHEET STEEL SUPPORTS AND COMBUSTIBLES 2 IN.

MINIMUM 6 IN. GLASS

FIBER INSULATION ALL AROUND

24 GAUGE

VENTILATED THIMBLE WITH

TWO 1 INCH AIR CHANNELS

CHIMNEY THIMBLE

CHIMNEY FLUE

MINIMUM CHIMNEY CLEARANCES FROM MASONRY TO

SHEET STEEL SUPPORTS AND COMBUSTIBLES 2 IN.

CHIMNEY LENGTH

FLUSH WITH INSIDE

OF FLUE

NONSOLUBLE

REFACTORY

CEMENT

MASONRY CHIMNEY CONSTRUCTED

TO NFPA 211

CHIMNEY CONNECTOR

TO HEATER

MINIMUM CLEARANCE

9 IN. ALL AROUND

SHEET STEEL SUPPORTS

(24 GAUGE MIN. THICKNESS)

CHIMNEY FLUE

SOLID INSULATED, LISTED

FACTORY-BUILT CHIMNEY LENGTH

USE CHIMNEY MFRS. PARTS TO

ATTACH CONNECTOR SECURELY

AIR SPACE

CHIMNEY CONNECTOR

TO HEATER

SOLID INSULATED, LISTED

FACTORY-BUILT CHIMNEY

LENGTH (12 IN. LONG MIN.)

MINIMUM CLEARANCE

2 IN. ALL AROUND

CHIMNEY THIMBLE

1 IN. AIR SPACE TO

CHIMNEY LENGTH

MASONRY CHIMNEY CONSTRUCTED

TO NFPA 211

SHEET STEEL SUPPORTS

(24 GAUGE MIN. THICKNESS)

CHIMNEY FLUE

MINIMUM CHIMNEY CLEARANCES FROM MASONRY TO

SHEET STEEL SUPPORTS AND COMBUSTIBLES 2 IN.

4. A chimney connector to a masonry chimney, except for 2" above (Part B of Figure 8), shall extend through

the wall pass-through system to the inner face of the chimney ue, but not beyond. It does not have to be

fastened in place so long as it cannot accidently be pulled out of the chimney or shoved into the chimney

ue. If fasteners are used to secure the chimney connector to a masonry chimney, the fasteners shall not

penetrate the chimney ue liner.

5. Any material used to close up any opening for the connector shall be noncombustible.

-14-

CAUTION!

NEVER USE GASOLINE, GASOLINE-TYPE

LANTERN FUEL, KEROSENE, CHARCOAL

LIGHTER FLUID, OR SIMILAR

LIQUIDS TO START OR "FRESHEN UP" A

FIRE IN THE HEATER. KEEP ALL SUCH LIQUIDS WELL

AWAY FROM THE HEATER WHILE IT IS IN USE.

CAUTION: A chimney re may cause ignition of wall studs or rafters which you thought were a safe distance

from the chimney. If you have a chimney re, have your chimney inspected by a qualied person before

using again.

WARNING!

NEVER STORE FLAMMABLE LIQUIDS,

ESPECIALLY GASOLINE. IN THE

VICINITY OF THE HEATER.

CAUTION!

OVERFIRING THE APPLIANCE MAY

CAUSE A HOUSE FIRE. IF A UNIT OR

CHIMNEY CONNECTOR GLOWS, YOU

ARE OVERFIRING.

WARNING!

NEVER OPERATE THIS HEATER WITH THE FUEL

DOOR OPEN.

WARNING!

USE ONLY THE LEGS PROVIDED WITH THIS

HEATER. REFER TO STEP 5 IN THE "INSTALLATION"

SECTION OF THIS MANUAL.

CAUTION!

USE WOOD OR WOOD-LIKE MATERIALS

ONLY. DO NOT USE COAL OR

CHARCOAL. COAL OR CHARCOAL WILL

DESTROY THE FIREBOX. DO NOT USE

DRIED LUMBER OR TREATED WOOD.

NOTE:

DO NOT ELEVATE FIRE OR USE WITH A GRATE,

BUILD FIRE DIRECTLY ON THE HEARTH.

WARNING!

DO NOT OBSTRUCT THE SPACE BENEATH THE

HEATER

SERVICE HINTS

Do not expect a heater to draw. It is the chimney that creates the draft. Smoke spillage into the house or

excessive buildup of water or creosote in the chimney are warnings that the chimney is not functioning properly.

Correct problem before using heater. Possible causes are:

1. The connector pipe may push into the chimney too far, stopping the draft. (Fig. 7)

2. Do not connect two heaters into the same chimney ue.

3. The chimney used for a heater must not be used to ventilate the cellar or basement. If there is a cleanout

opening at the base of the chimney, it must be closed tightly.

4. If the chimney is operating too cool, water will condense in the chimney and run back into the stove.

Creosote formation will be rapid and may block the chimney. Operate the heater at a high enough re to

keep the chimney warm preventing this condensation.

5. If the re burns well but sometimes smokes or burns slowly, it may be caused by the chimney top being lower

than another part of the house or a nearby tree. The wind blowing over a house or tree, falls on top of the

chimney like water over a dam, beating down the smoke. The top of the chimney should be at least 3 feet

above the roof and be at least to 2 feet higher than any point of the roof within 10 feet.

Chimney Maintenance

CREOSOTE - FORMATION AND NEED FOR REMOVAL

When wood is burned slowly, it produces tar and other organic vapors, which combine with expelled moisture

to form creosote. The creosote vapors condense in the relatively cool chimney ue of a slow burning re. As a

result, creosote residue accumulates on the ue lining. When ignited, this creosote makes an extremely hot re.

The chimney connector and chimney should be inspected at least twice monthly during the heating season to

determine if a creosote buildup has occurred.

If creosote has accumulated, it should be removed. Failure to remove creosote may cause a house re. Creosote

may be removed by using a chimney brush or other commonly available materials.

Chimney res burn very hot. If the chimney connector should glow red, immediately call the re department,

then reduce the re by blocking/closing the inlet air. Since this is a single burnrate heater you should use a non-

combustible material to block inlet air openings. If the re is burning vigorously, spray a multipurpose dry chemical

extinguisher onto the re in the stove if it can be done safely. Avoid introducing water into the chimney if possible

as water could damage the heated ue liner.

-15-

Your heating unit was designed to burn wood only; no other materials should be burned. Waste and other

ammable materials should not be burned in your stove. Any type of wood may be used in your stove, but

specic varieties have better energy yields than others. Please consult the following table in order to make the

best possible choice.

WOODSTOVE UTILIZATION

It is EXTREMELY IMPORTANT that you use DRY WOOD only in your wood stove. The wood should have dried for 9

to 15 months, such that the humidity content (in weight) is reduced below 20% of the weight of the log. It is very

important to keep in mind that even if the wood has been cut for one, two or even more years, it is not necessarily

dry if it has been stored in poor conditions.

Under extreme conditions it may rot, instead of drying. This point cannot be over stressed; the vast majority of

the problems related to the operation of a wood stove is caused by the fact that the wood used was too damp

or has dried in poor conditions. These problems can be:

– ignition problems

– creosote build-up causing chimney res

– low energy yield

– blackened windows

– incomplete log combustion

Smaller pieces of wood will dry faster. All logs exceeding 6” in diameter should be split. The wood should not be

stored directly on the ground. Air should circulate through the cord. A 24” to 48” air space should be left between

each row of logs, which should be placed in the sunniest location possible. The upper layer of wood should be

protected from the elements but not the sides.

TESTING YOUR WOOD

When the stove is thoroughly warmed, place one piece of split wood (about ve inches in diameter) parallel to

the door on the bed of red embers.

Keep the air control full open by pulling on it and close the door. If ignition of the piece is accomplished within

90 seconds from the time it was placed in the stove, your wood is correctly dried. If ignition takes longer, your

wood is damp.

If your wood hisses and water or vapor escapes at the ends of the piece, your wood is soaked or freshly cut.

Do not use this wood in your stove. Large amounts of creosote could be deposited in your chimney, creating

potential conditions for a chimney re.

TYPE

WEIGHT

(LBS. CU. FT., DRY)

PER CORD

EFFICIENCY

RANKING

SPLITS

M I L L I O N S

BTU’s/CORD

Hickory 63 4500 1.0 Well 31.5

White Oak 48 4100 .9 Fair 28.6

Red Oak 46 3900 .8 Fair 27.4

Beech 45 3800 .7 Hard 26.8

Sugar Maple 44 3700 .6 Fair 26.2

Black Oak 43 3700 .6 Fair 25.6

Ash 42 3600 .5 Well 25.0

Yellow Birch 40 3400 .4 Hard 23.8

Red Maple 38 3200 .3 Fair 22.6

Paper Birch 37 3100 .3 Easy 22.1

Elm/Sycamore 34 2900 .2 Very Difcult 20.1

Red Spruce 29 1800 .1 Easy 16.1

-16-

THE FIRST FIRES

The fresh paint on your stove needs to be cured to preserve its quality. Once the fuel charge is properly ignited,

only burn small res in your stove for the rst four hours of operation.

Make sure that there’s enough air circulation while curing the stove. The odors could be smelled during the 3 or

4 rst res. Never start your stove outside. You will not be able to see if you are over heating.

RELOADING

Once you have obtained a good bed of embers, you should reload the unit. Open the door very slowly; open it

one or two inches for 5 to 10 seconds, before opening it completely to increase the draft and thus eliminate the

smoke which is stagnant in a state of slow combustion in the stove. Then bring the red embers to the front of the

stove and reload the unit.

It is important to note that wood combustion consumes ambient oxygen in the room. In the case of negative

pressure, it is a good idea to allow fresh air in the room, either by opening a window slightly or by installing a fresh

air intake system on an outside wall.

Creosote - Formation and Need for Removal - When wood is burned slowly, it produces tar and other organic

vapors, which combine with expelled moisture to form creosote. The creosote vapors condense in the relatively

cool chimney ue of a slow-burning re. As a result, creosote residue accumulates on the ue lining. When

ignited, this creosote makes an extremely hot re. The chimney connector and chimney should be inspected

at least once every two months during the heating season to determine if a creosote build-up has occurred. If

creosote has accumulated (3mm or more), it should be removed to reduce the risk of a chimney re.

We strongly recommend that you install a magnetic thermometer on your smoke exhaust pipe, approximately

18” above the stove. This thermometer will indicate the temperature of your gas exhaust fumes within the smoke

exhaust system. The ideal temperature for these gases is somewhere between 275°F and 500°F. Below these

temperatures, the build-up of creosote is promoted. Above 500 degrees, heat is wasted since a too large quantity

is lost into the atmosphere.

TO PREVENT CREOSOTE BUILD UP

• Always burn dry wood. This allows clean burns and higher chimney temperatures, therefore, less creosote

deposit.

• The secondary combustion can only take place if the rebox is hot enough.

• Always check for creosote deposit once every two months and have your chimney cleaned at least once a

year.

If a chimney or creosote re occurs, close all dampers (if applicable) immediately. Wait for the re to go out and

the heater to cool, then inspect the chimney for damage. If no damage results, perform a chimney cleaning to

ensure there is no more creosote deposits remaining in the chimney.

CAUTION:

Never alter the damper slide or the adjustment range to increase FIRING ring for any reason. Doing so could

result in heater damage and will void your warranty.

WARNINGS:

• NEVER OVERFIRE YOUR STOVE. IF ANY PART OF THE STOVE STARTS TO GLOW RED, OVER FIRING IS

HAPPENING.

• THE INSTALLATION OF A LOG CRADLE OR GRATES IS NOT RECOMMENDED IN YOUR WOOD STOVE BUILD FIRE

DIRECTLY ON HEARTH.

-17-

CAUTIONS:

ASHES COULD CONTAIN HOT EMBERS EVEN AFTER TWO DAYS WITHOUT OPERATING THE STOVE.

MAINTENANCE

Your wood stove is a high efciency stove and, therefore requires little maintenance. It is important to perform

a visual inspection of the stove every time it is emptied, in order to insure that no parts have been damaged,

in which case repairs must be performed immediately. Inspect and clean the chimney and connector pipe

periodically for creosote buildup or obstructions.

GASKETING

It is recommended that you change the door gasket (which makes your stove door air tight) once a year, in

order to insure good control over the combustion, maximum efciency, and security. To change the door gasket,

simply remove the damaged one. Carefully clean the available gasket groove, apply a high temperature silicone

sold for this purpose and install the new gasket. You may light up your stove again approximately 24 hours after

having completed this operation.

PAINT

Only clean your stove with a dry soft cloth that will not harm the paint nish. If the paint becomes scratched or

damaged, it is possible to give your wood stove a brand new look, by repainting it with a 1200° F heat resistant

paint. For this purpose, simply scrub the surface to be repainted with ne sand paper, clean it properly, and apply

thin coats (2) of paint successively.

SECONDARY AIR TUBES

The secondary air tubes must be cleaned with a wire brush. If debris remains in holes lightly tap with a wooden

stick to remove.

WARNING:

NEVER OPERATE THE STOVE WITHOUT A GASKET OR WITH A BROKEN ONE. DAMAGE TO THE STOVE OR EVEN

HOUSE FIRE MAY RESULT.

-18-

Parts List

In order to maintain warranty, components must be replaced using original manufacturers parts purchased through your

dealer or directly from the appliance manufacturer. Use of third party components will void the warranty.

KAO Wool

88228 1

Door Assembly

892515 1

Handle Assembly

892722 1

Bafe

892510 1

Bottom Channel

892508 1

Leg

40817 4

Hearth Extension

40771 1

6" Damper

40398 1

Rod

892533 4

3/8" Rope Joint Top

88033 8.75 ft

Tube Weldment

892516 1

Main Top

40774 1

-19-

Parts List

In order to maintain warranty, components must be replaced using original manufacturers parts purchased through your

dealer or directly from the appliance manufacturer. Use of third party components will void the warranty.

6" Damper Pivot Pin

892517 1

Handle Bracket

89975 1

Flue Collar

40784 1

Main Bottom

40772 1

Door Frame

40302 1

Main Back

40299 1

Main Side

40775 2

-20-

NOTES

La page charge ...

United States Stove 1269E Le manuel du propriétaire

Marque: United States Stove

Modèle: 1269E

Catégorie: Poêle à bois

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: United States Stove 1269E Owner's manual

United States Stove 1269E Le manuel du propriétaire

United States Stove 1269E Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents