Swing-N-Slide Playsets 4367 Mode d'emploi

Taper
Mode d'emploi

Ce manuel convient également à

Call Us First!
DO NOT RETURN TO STORE.
For immediate help with assembly or product information
call our toll-free number:
1-800-437-0784
April through October M - F 8:00 AM to 6:00 PM EST
Saturday 8:30 AM to 4:30 PM EST
November through March M - F 8:00 AM to 5:00 PM EST
or email:
customerservice@backyard-play.com
Our staff is ready to provide assistance.
STOP!
STOP!
2692
- NOTICE -
This playset product is not intended for public use. It is intended for
residential application and is not warranted for public or commercial use.
4HISPAGEINTENTIONALLYLEFTBLANK
11/12/2013
- BEFORE YOU BEGIN -
Your premium playset is manufactured from wood which has many natural characteristics and blemishes that may be present in some of the pieces in your playset. These natural characteristics may include knots or mi-
nor cracks/splits. All individual parts have been cut to provide a smooth and safe surface. All parts have been inspected to assure we pack only the safest, most durable wood product. Any minor blemishes in your playset
will not affect the strength, durability, or structural integrity of the À nished product. Our limited warranty does not cover the imperfections not resulting in structural failure.
2692
Playset
First...
Check with your homeowner’s association before
assembling.
Read instructions thoroughly before you begin. If you
have purchased accessories to accompany this play
set, please read all installation instructions before
beginning assembly of this structure.
Check All Parts
If a part is missing, circle the part in question and call.
Important
In a drawing, a dotted line represents a part hidden
from view (like a part under a panel).
Adult Assistance required
Assistance is necessary to handle, À t
and secure some components.
Squareness is very Important!
Start with a level surface and keep 90° corners and 90°
perpendiculars throughout the assembly to ensure all
components À t together.
Safety!
Check for protruding screws and bolts, verify all screw
and bolt lengths during assembly.
Always wear OSHA-APPROVED safety
glasses throughout assembly process.
Tools Required
Socket Set
Hammer
9/16" Combination
Wrench
3/16" Allen Wrench
#2 Square Drive
Bit (included)
#3 Phillips Bit
Cordless Drill
w/Charger
1/8" Drill Bit
7/16" Drill Bit
1/4" Drill Bit
3/8" Drill Bit
Tape Measure
Level
C - Clamps
8' Step Ladder
Framing/Speed
Square
- BEFORE YOU BEGIN -
Recommended for Ages 3 to 11
Backyard Play Systems
Customer Service
1-800-437-0784
1000 Ternes Drive
Monroe, MI 48162
- NOTICE -
This playset product is not intended for public use. It is intended for
residential application and is not warranted for public or commercial use.
Model 4185,
4332, 4333,
4334, 4335,
6246, 6351,
6352, 6353,
6354, 6371
2
Wear safety glasses during drilling, assembly of your playset.
Children should not be allowed in the playset assembly and build area.
Note the hole orientation on parts to avoid having to take parts
apart later.
Some steps require the assistance of two people to ensure proper
assembly, safety during assembly, as well as preventing any damage
to the playset.
All hex bolts and lag bolts require a lock washer or lock nut.
To properly install lock nuts, two to three threads must protrude past the
lock nut and be exposed once tightened.
Due to wood characteristics and the manufacturing process hex bolts
may protrude past a surface. If this condition occurs add additional
supplied washers to eliminate bolt protrusion.
To aid in proper assembly pound T-nuts into their respective hole
prior to assembly
Pound in T-nuts while the part is on the ground to ensure proper seating.
Use a soft material under parts when pounding in T-nuts to ensure
no scratching or de-facing of parts.
Make sure all fasteners used are as speciÀ ed. Using a fastener not
speciÀ ed in a particular application may result in too much thread
exposure or not enough thread engagement.
ASSEMBLY SAFETY and HELPFUL HINTS
STOP!!! Check all parts and hardware before beginning. If any parts are
missing or damaged please circle and call the phone number listed.
DO NOT CONTACT THE STORE OR RETURN YOUR PLAYSET !
KEEP THIS INSTALLATION MANUAL FOR FUTURE CARE
AND MAINTENANCE REFERENCE.
To aid in making your playset assembly easier,
here is a listing of some helpful hints.
*IMPORTANT HARDWARE INFORMATION*
3
SAFETY WARNINGS
This playset has been designed for use by a maximum of eight occupants at one time having a
combined weight of 1,200 pounds. (This weight does not include occupants in the sandbox area.)
This playset is recommended for children (3) through (11) years of age.
On-site adult supervision for children of all ages is recommended.
Instruct children not to walk close to, in front of, behind, or between moving items.
Instruct children not to twist swing chains or ropes or loop them over the top support bar since this may
reduce the strength of the chain or rope.
Instruct children to avoid swinging empty seats.
Teach children to sit in the center of the swings with their full weight on the seats.
Instruct children not to use the equipment in a manner other than intended.
Instruct children not to get off equipment while it is in motion.
Parents should dress children appropriately (examples would include the use of well-À tting shoes and
the avoidance of ponchos, scarves, and other loose-À tting clothing that is potentially hazardous
while using equipment).
Instruct children not to climb when the equipment is wet. Slippery surfaces may cause a hazard.
Verify that suspended climbing ropes, chain, or cable are secured at both ends.
Verify that suspended climbing ropes, chain, or cable cannot be looped back on itself.
Instruct children not to attach items to the playground equipment that are not speciÀ cally designed for
use with the equipment, such as, but not limited to, jump ropes, clothesline, pet leashes, cables and
chain as they may cause a strangulation hazard.
Instruct children to remove their bike or other sports helmet before playing on the playground equipment.
Instruct children to not walk or run up slides.
Instruct children to not pick up slides or ramps as this may cause damage or breakage.
Place the equipment on level ground not less than six (6) feet from any obstructions. Be sure to look
overhead for any obstructions above the playset.
Do not use the equipment until fully erected per this playset instruction manual, bolts tightened and
the playset is anchored to the ground.
NOTICE:
This playset product is not intended for public use. It is intended for residential application
and is not warranted for public or commercial use.
Please read carefully. Observing the following statements and warnings
reduces the likelihood of serious or fatal injury.
4
Periodic maintenance is required to ensure safe enjoyment
of your playset and optional accessories.
Observing the following procedures reduces the likelihood of serious or fatal injury.
PLAYSET CHECKLIST
At the beginning of each play season:
MAINTENANCE
Activity on your playset and optional accessories may loosen fasteners. Check all lock nuts, hex and
lag bolts, quick clips, spring clips, acorn nuts, wood screws, and swing hangers for tightness and
tighten as required. T-nuts should be inspected for full and proper seating into the wood.
Checking, splitting and surface cracking are characteristics of all wooden playsets. This is caused by varying
seasonal temperatures and moisture conditions. To minimize this checking and/or cracking you may coat your
playset with a water repellent.
Tighten all hardware.
Lubricate all metallic moving parts per manufacturer’s instructions.
Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose, cracked, or missing.
Check all moving parts including swing seats, ropes, cables, and chains for wear, rust, or other deterioration. Replace as needed.
Check metal parts for rust. If found, sand and repaint using a nonleaded-based paint meeting the requirements of 16 CFR 1303.
Check all wood members for deterioration and splinters. Sand down splinters and replace deteriorating wood members.
Reinstall any plastic parts, such as swing seats or any other items that were removed for the cold season.
Rake and check depth of loose À ll protective surfacing materials to prevent compaction and to maintain appropriate depth. Replace as necessary.
Tighten all hardware.
Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose, cracked, or missing.
Rake and check depth of loose À ll protective surfacing materials to prevent compaction and to maintain appropriate depth. Replace as necessary.
Lubricate all metallic moving parts per manufacturer’s instructions.
Check all moving parts including swing seats, ropes, cables, and chains for wear, rust, or other deterioration. Replace as needed.
At the end of each play season or when the temperature drops below 10°F remove plastic swing seats, tents, sandbox cover, tire swing,
slide and other items as speciÀ ed by the manufacturer and take indoors or do not use.
Rake and check depth of loose À ll protective surfacing materials to prevent compaction and to maintain appropriate depth.Replace as necessary.
When you are ready to dispose of your playset, make sure that all metal, plastic and wood components are disposed of in
accordance with local waste ordinances.
Buyer and/or owner should disassemble and dispose of the playground equipment in such a way that no unreasonable hazards will
exist at the time the swing set is discarded.
5
PLAYGROUND SURFACING MATERIALS
SECTION 4 OF THE CONSUMER PRODUCT SAFETY COMMISSION’S OUTDOOR HOME
PLAYGROUND SAFETY HANDBOOK
9
Select Protective Surfacing
One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under
and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with
ASTM SpeciÀ cation F 1292. There are different types of surfacing to choose from; whichever product you select, follow these guidelines:
NOTE: Do not install home playground equipment over concrete, asphalt, or any other hard surface. A fall onto a hard surface can result in
serious injury to the equipment user. Grass and dirt are not considered protective surfacing because wear and environmental factors can reduce
their shock absorbing effectiveness. Carpeting and thin mats are generally not adequate protective surfacing. Ground level equipment – such as
a sandbox, activity wall, playhouse or other equipment that has no elevated play surface – does not need any protective surfacing.
Loose-Fill Materials:
Maintain a minimum depth of 9 inches of loose- À ll materials such as wood mulch/chips, engineered wood À ber (EWF), or shredded/recycled
rubber mulch for equipment up to 8 feet high; and 9 inches of sand or pea gravel for equipment up to 5 feet high. NOTE: An initial À ll level of
12 inches will compress to about a 9- inch depth of surfacing over time. The surfacing will also compact, displace, and settle, and should be
periodically reÀ lled to maintain at least a 9- inch depth.
Use a minimum of 6 inches of protective surfacing for play equipment less than 4 feet in height. If maintained properly, this should be
adequate. (At depths less than 6 inches, the protective material is too easily displaced or compacted.)
Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape edging. Don’t forget to account for
water drainage. U.S Consumer Product Safety Commission, Washington, D.C., 20207 or call the toll-free hotline :1-800-638-2772
Check and maintain the depth of the loose-À ll surfacing material. To maintain the right amount of loose-À ll materials, mark the correct level on
play equipment support posts. That way you can easily see when to replenish and/or redistribute the surfacing.
Do not install loose À ll surfacing over hard surfaces such as concrete or asphalt.
Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles:
You may be interested in using surfacing other than loose-À ll materials – like rubber tiles or poured-in-place surfaces.
Installations of these surfaces generally require a professional and are not “do-it-yourself” projects.
Review surface speciÀ cations before purchasing this type of surfacing. Ask the installer/manufacturer for a report showing that the product
has been tested to the following safety standard: ASTM F 1292 Standard SpeciÀ cation for Impact Attenuation of Surfacing Materials within the
Use Zone of Playground Equipment. This report should show the speciÀ c height for which the surface is intended to protect against serious head
injury. This height should be equal to or greater than the fall height – vertical distance between a designated play surface (elevated surface for
standing, sitting, or climbing) and the protective surfacing below – of your play equipment.
Check the protective surfacing frequently for wear.
Placement
Proper placement and maintenance of protective surfacing is essential. Be sure to
Extend surfacing at least 6 feet from the equipment in all directions.
For to-fro swings, extend protective surfacing in front of and behind the swing to a distance equal to twice the height of the top bar from which
the swing is suspended.
For tire swings, extend surfacing in a circle whose radius is equal to the height of the suspending chain or rope, plus 6 feet in all directions.
2H 2H
H
L
6 ft.
6 ft.
6 ft. 6 ft.
L+6 ft.
6 ft.
6 ft.
Use Zone for Single-Axis Swings Use Zone for Multi-Axis Swings
Denotes Use Zone with Protective Surfacing
Denotes Use Zone with Protective Surfacing
9 This information has been extracted from the CPSC publications “Playground Surfacing—Technical Information Guide” and “Handbook for Public
Playground Safety.” Copies of these reports can be obtained by sending a postcard to the: OfÀ ce of Public Affairs, U.S. Consumer Product Safety
Commission, Washington, D.C., 20207 or call the toll-free hotline: 1-800-638-2772
6
ORIENTATION
*Hint*
Throughout this manual references made to the Left Side,
the Right Side, the Front Side and the Back Side of the playset serve
as a consistent reminder to help with assembly.
PLAYSET
LEFT SIDE
FRONT SIDE
BACK SIDE
RIGHT SIDE
7
IMPORTANT!
A
A
B
B
Use these Assembly Procedure Hints throughout the installation process.
1. All Lag Bolts must have pre-drilled holes. Use a 1/4” drill bit for all 3/8” Lag Bolts.
Use a 3/16” drill bit for all 5/16” Lag Bolts. Pre-drilling pilot holes will help prevent Screws
and Lag Bolts from breaking and wood from splitting during assembly.
2. In areas where drilling a larger 1/2” hole is neccessary, such as when installing T-Nuts,
(Fig. 1) the recommended procedure is to first drill-through a 1/4” pilot hole from the
Hex Bolt side and then drill the larger 1/2” hole from the opposite T-Nut side. This will
help avoid splintering the wood. The “Drill Both Sides ICON” (Fig. 1) will remind you to
drill according to this procedure. Be sure to clean through-holes of debris before
inserting Hex Bolts.
3. When assembling parts that are difficult to hold in position while pre-drilling pilot holes
or assembling, use a clamp to keep parts aligned or in position. The “Clamp ICON
(Fig. 2) will advise you to use this procedure.
Fig. 1 (example)
Fig. 2
Drill Both Sides
ICON
Clamp ICON
1/4” pilot hole
1/2” drill through
DO NOT OVER-TIGHTEN LAG BOLTS
8
WOOD PARTS LIST
x1
x1
WOOD PARTS
x1
x2
x11
x1
x3
x1
x2
x16
x1
x1
x1
x1
3/4 x 5-1/2 x 23-3/4"
x2
x4
3/4 x 3 x 38-7/8"
1 x 3-1/2 x 45-1/8"
1-3/8 x 3-3/8 x 51"
1-3/8 x 3-3/8 x 47-3/4"
2501-CC
2502-CC
2521-CC
2522-CC
2515-CC
x4
x1
1 x 3-1/2 x 15-3/8"
1-1/2 x 2-1/2 x 24"
2524-CC
2490-CC
2527-CC
2500-CC
2504-CC
2508-CC
2503-CC
x2
x1
2510-CC
2520-CC
2505-CC
2507-CC
2517-CC
2518-CC
2523-CC
2539-CC
1 x 3-1/2 x 27"
x1
2514-CC
x2
x2
2543-CC
2525-CC
1 x 3-1/2 x 40-1/2"
1-3/8 x 3-3/8 x 51"
3 x 3 x 45-1/8"1 x 5-1/2 x 45-1/8"
1 x 3-1/2 x 47"
1-1/2 x 3-1/2 x 47-1/8"
1 x 3-1/2 x 47-1/8"
5/8 x 3-1/4 x 29-3/4"
x1
1 x 3-1/2 x 17"
2222-CC
x8
3/4 x 5-1/2 x 23-3/4"
2519-CC
3/4 x 2-1/2 x 45-1/8"
x1
2516-CC
x7
2509-CC
3/4 x 5-1/2 x 44-7/8"
x1
2506-CC
1-1/2 x 3-1/2 x 18"
x8
1020-CC
1-3/8 x 3-3/8 x 51"
3 x 3 x 95"
1 x 3-1/2 x 53-7/8"
1 x 5-1/2 x 71-3/4"
1 x 3-1/2 x 68-1/2"
3-3/8 x 5-3/8 x 95"
3 x 3 x 95"
3 x 3 x 95"
1 x 3-1/2 x 45-1/8"
x1
2526-CC
x2
1 x 3-1/2 x 12"
2568-CC
1015-CC
x1
1 x 1-3/8 x 17"
9
ACCESSORIES
HARDWARE
Safety Handle
IN BAG
x2
x3
x6
x1
Rope
Plaque
Trapeze
Swing
Climbing Rocks
x1
x4
Telescope Steering Wheel
x1
2434 2451
2630 2405
2073 2603
x6
Swing Hanger
2631
x1
2435
x1
x1
x4
x1
x1
x2
x1
90
o
Angle Bracket Plate
L-Bracket
Swing Beam Flat Plate
Swing Beam Angled Plate Left Swing Beam Angled Plate RightSwing Beam 90
o
Plate
2411
2448
2601-A
2447
2485
2412 2449
x1
x1
SlideStake
2099
2654
x1
2438
-or-
10
PLAYSET FASTENERS
1”
1”
3/8” T - NUT
5/16” T - NUT
3/8” FLAT WASHER
1/4” x 1” FENDER WASHER
3/16” x 1” FENDER WASHER
3/8” LOCK WASHER
5/16” FLAT WASHER
5/16” LOCK
WASHER
1/4” FLAT
WASHER
1/4” LOCK
WASHER
TRUSS HEAD
SCREW
3/4”
3/8” LOCK NUT
2-1/2”
PAN HEAD
SCREW
2-1/2”
3/8”
3/8”
3/8”
5/16”
5/16”
1/4”
1/4”
1/4” ROCK WALL HARDWARE
T - Nut
Lock
Washer
Hex Bolt
Flat
Washer
1-1/4”
x20
x4
x37
x66
x44
x2
x4
x2
x10
x10
x6
x12
x4
x4
2452 BAG
11
PLAYSET FASTENERS
3/8"
LAG BOLT
WOODSCREWS
4"
2-1/2"
3"
1-1/4"
2"
3/8"
5"
3/8"
2-1/4"
3/8"
2"
3/8"
3/8” HEX HEAD BOLTS
3-3/4"
1-1/4"
3/8"
1-3/4"
3/8"
3/8"
LAG BOLT
3"
x4
x1
x4
x26
x2
x18 x100
x76
x86
x1
x6
x1
x1
x1
#2 SQUARE
DRIVE BIT
12
3/8" TORQUE
WASHER
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3"
3-3/4"
4-1/4"
6-1/4"6" 8-1/2"
ACTUAL SIZE SHOWN
x5
x2 x6 x2 x2 x2 x1
1-1/2”
3/8”
BUTTON HD.
SCREW
3/8”
BUTTON HD.
SCREW
x2
x2
1-1/4”
5/16” 5/16”
13
PLAYSET SET-UP
PLAYSET SET-UP WITH MONKEY BARS
SAFETY AREA
SAFETY AREA
FRONT SIDE
FRONT SIDE
BACK SIDE
BACK SIDE
6' SAFETY AREA
6' SAFETY AREA
6' SAFETY AREA
6' SAFETY AREA
LEFT SIDELEFT SIDE
RIGHT SIDE RIGHT SIDE
SWING
SWING
SLIDE
SLIDE
ROCK
WALL
ROCK
WALL
MONKEY
BARS
18'-2"
18'-2"
8'-4"
14'-2"
HEIGHT
10'-2"
HEIGHT
10'-2"
14
FORT
BASE
Align braces with pre-drilled holes.
FLIP ASSEMBLY OVER TO INSTALL BOTTOM BRACE.
Flush
Flush
3-3/4" Hex Bolt
Lock Washer
Flat Washer
x2
x1
2507-CC
1 x 5-1/2 x 45-1/8"
90°
Ensure all bracing is square before
installing wood screws.
FORT
CORNER POSTS
Align braces with pre-drilled holes.
Hole for Climbing Rope
BOTTOM
Flush
Flush
Flush
T-Nut
Flush
x1
x1
2503-CC
2543-CC
3 x 3 x 95"
3 x 3 x 95"
x1
1 x 3-1/2 x 45-1/8"
x1
1 x 4 x 45-1/8"
2526-CC
2501-CC
x4
x6
3-3/4" Hex Bolt
Lock Washer
Flat Washer
90°
47"
4"
4"
12-5/8"
Note 2 hole location.
2543-CC
15
FORT
CORNER POSTS
x4
Align braces with
pre-drilled holes.
Large holes toward top
Large holes
toward bottom
Flush
Flat Washer
Lock Washer
3-3/4" Hex Bolt
5" Hex Bolt
Flat Washer
x6
1 x 3-1/2 x 45-1/8"
T-Nut
x4
x2
x2
Ensure all bracing is
square before installing
wood screws.
Flush
2501-CC
x1
2508-CC
1 x 5-1/2 x 71-3/4"
x1
1 x 5-1/2 x 45-1/8"
2507-CC
FORT
CORNER POSTS
x4
Note 1 hole
location.
Align braces with pre-drilled holes.
Flush
3" Wood Screw
Flush
Flush
Flush
3-3/4" Hex Bolt
Lock Washer
Flat Washer
x1
x1
2503-CC
2543-CC
3 x 3 x 95"
3 x 3 x 95"
x2
1 x 3-1/2 x 45-1/8"
2501-CC
90°
47"
4"
T-Nut
x6
x4
Lock Nut
Flat Washer
Note 2 hole location.
Note 2 hole location.
16
FORT
BASE
Align braces with pre-drilled holes.
FLIP ASSEMBLY OVER TO INSTALL BOTTOM BRACE.
Flush
Flush
3-3/4" Hex Bolt
Lock Washer
Flat Washer
x2
x1
2507-ST
1 x 5-1/2 x 45-1/8”
90°
FORT
CONNECT FRAME SECTIONS
3-3/4" Hex Bolt
Lock Washer
Flat Washer
5" Hex Bolt
Lock Washer
Flat Washer
Align braces with pre-drilled holes.
x4
x2
x2
T-Nut x4
Lock
Nut
Flat
Washer
ENSURE THESE
HOLES ARE ON
THIS SIDE.
17
FORT CONNECT FRAME SECTIONS
x36
47"
47"
3" Wood Screws
Ensure 47" measurement from
bottom of base to top of boards.
Reinforce bracing with 3" wood
screws at all pre-drilled holes.
FORT
DECK CLEAT
Flush
Flush
EQUAL
EQUAL
EQUAL
EQUAL
3/4 x 2-1/2 x 45-1/8"
x1
2516-CC
x4
2-1/2" Wood Screws
18
2-1/2" Wood Screws
1-1/4" Wood Screws
x28
x14
FORT
DECK PLANKS
Flush
evenly spaced
x7
2509-CC
3/4 x 5-1/2 x 44-7/8"
Flush with
post.
FORT
DECK PLANKS
1-1/4" Wood Screws
3/4 x 4 x 38-7/8"
x2
2510-CC
x8
x4
2-1/2" Wood Screws
Flush along
outer edge.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

Swing-N-Slide Playsets 4367 Mode d'emploi

Taper
Mode d'emploi
Ce manuel convient également à

dans d''autres langues