brondell Swash SE400 Le manuel du propriétaire

Taper
Le manuel du propriétaire
OWNER’S MANUAL
Swash SE400 Advanced Bidet Toilet Seats
SE400-EW
SE400-RW
2
Attach Proof of Purchase to This Page
Adjunte prueba de compra a esta página
Joindre une preuve d’achat à cette page
1
CONTENTS
This manual contains important safety information. Before operating the
bidet, please read this manual thoroughly, and retain it for future reference.
PRODUCT INSTALLATION
GENERAL INFO
PRODUCT OPERATION
02 SAFETY INFORMATION
06
06
07
08
PRODUCT INFORMATION
Product Features
Product Dimensions
Product Parts
09
09
10
11
13
PRODUCT INSTALLATION
Installation Parts
Before Installation
Swash Installation
External Bidet Filter Installation
14
14
16
18
OPERATING THE SWASH
SE400 Control Panel
Using the SE400
Special Mode Operations
TECHNICAL INFO
TRANSLATIONS
19 PRODUCT SPECIFICATIONS
20
20
20
21
21
MAINTENANCE
Seat Cleaning & Removal
Nozzle Cleaning
Cleaning the Mesh Filter
Product Storage & Use
22 TROUBLESHOOTING
25 WARRANTY
26 CONTACT
1ENGLISH
27 SPANISH
54 FRENCH
2
SAFETY INFORMATION
(IMPORTANT SAFEGUARDS)
READ ALL INSTRUCTIONS BEFORE USING
BE CAREFUL TO KEEP THIS SAFETY INFORMATION. PLEASE READ THIS INFORMATION TO PREVENT
PROPERTY LOSS AND ENSURE SAFETY.
DANGER: If not observed, serious injury or even death may occur as a result.
WARNING: If not observed, serious physical injury or property damage may occur as a result.
CAUTION: If not observed, minor physical injury or property damage may occur as a result.
SAVE THESE INSTRUCTIONS
DANGER Failure to observe the following warnings may result in electric shock, fire,
personal injury, property damage or product damage.
Failure to observe the following warnings may result in electric shock, fire, personal injury, property
damage or product damage:
• Do not use a damaged power plug or plug into a loose electric outlet.
• Do not move the product by pulling the power cord.
• Do not handle the product or power plug with wet hands.
• Do not forcefully bend the power cord or place heavy objects on it to prevent it from being damaged
or deformed.
• Do not connect and pull out the power plug or cord repeatedly.
• Unplug the product before cleaning, repairing, inspecting, or replacing parts.
• Remove any dust or water from the power plug prior to plugging in.
• Do not plug the product into an electrical outlet or power strip that is being used by too many other
products. Use an electrical outlet adequate for the wattage of the product rated for a minimum of
15 amps.
• If the power cord is damaged, do not attempt to repair, modify, or replace the cord yourself. Contact
the Brondell Service Center toll free at 888-542-3355 or email us through our website.
• If the product produces a strange noise, a burning smell, or emits smoke, unplug it immediately from
the electrical outlet and contact Brondell. Failure to do so may result in electric shock or fire.
• Do not insert any wires or sharp objects into any product gaps. This may result in electric shock, fire,
or product damage.
• Do not place an electronic or gas heater near the product or dispose of any burning materials
such as a lit cigarette in the toilet. This may result in fire or product deformation. Do not place any
containers filled with water or other liquids, food, metallic objects, or any flammable material on top
of the product. If foreign material enters the product, this may result in electric shock or fire.
3
• Do not plug in, operate, or store the unit in locations where flammable or combustible materials are
used or kept.
• Do not use industrial water, or gray water for the supply, as this may cause skin damage or disease.
• Turn o the main water supply valve when cleaning.
• For children and seniors who may have diculties with adjusting temperatures or those with
sensitive skin or impaired heat sensitivity, set the temperature of the wash spray and seat to “low”
or “o” to prevent burning.
• Close supervision is necessary when this product is used by children, seniors, or persons requiring
general assistance.
• Do not press the buttons using excessive force.
• Do not stand on top of or place any heavy objects onto the seat cover.
• Use this product for its intended use only, as described in this manual. Do not use any attachments
that are not recommended by Brondell.
SAVE THESE INSTRUCTIONS
SAFETY INFORMATION
(IMPORTANT SAFEGUARDS)
DANGER Failure to observe the following warnings may result in electric shock, fire,
personal injury, property damage or product damage.
• Do not use the product in locations exposed to excessive moisture and do not splash water onto
the product.
• While cleaning the bathroom, pull the power plug out of the electrical outlet and exercise
caution to ensure that water or cleaning supplies do not splash onto the bidet. Failure to do so
may result in electric shock or fire.
• If foreign material enters the product, pull the power plug out of the electrical outlet, turn o the
main water valve, and call the Brondell Service Center.
• Do not disassemble, repair, or modify the product yourself.
• Do not use the product while wet from bathing or showering.
• Do not place or store the product where it can fall or be pulled into a tub or sink.
• Do not place in or drop the product into water or any other liquid.
• Do not reach for the product if it has fallen into water. Unplug the product immediately and call
the Brondell Service Center.
• Do not use the product if it is not working properly. Please unplug the product immediately,
close the main water supply valve, and call the Brondell Service Center at 888-542-3355.
Failure to do so may result in electric shock, fire, or flooding.
WARNING Failure to observe the following warnings may result in electric shock, fire,
personal injury, property damage or product damage.
4
• Do not connect the main water supply to the hot water pipe or supply (only connect to the
cold water supply).
• After the installation, make sure to check all water supply connections for leaks. Rubber
washers should be in place for the water connection hoses & T-Valve.
• Do not open/close the seat or seat cover with excessive force.
• Exercise caution that urine does not come into contact with the product - failure to do so may
result in bad odors or malfunction.
• If the product will not be used for a long period of time, unplug the power cord, close the
main water supply valve, and drain any water in the water tank.
• Do not pull out the bidet hose using excessive force.
• Do not use thinner, benzene, acidic chemicals, chloride, or hydrochloric acid detergent on or
near the product. This may result in corrosion to the metal parts or discoloration or scratches
to the bidet body.
• This appliance is not intended for use by persons (including children and seniors) with
reduced physical, sensory, or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning the use of the appliance
by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Never operate this product if it has a damaged cord or plug, if it is not working properly, if it
has been dropped or damaged, or dropped into water. Contact the Brondell Service Center for
examination and repair.
• Keep the cord away from heated surfaces and heating vents.
• Never block the air openings of the product or place it on a soft surface, such as a bed or couch,
where the air openings may be blocked. Keep the air openings free of lint, hair, etc.
• Never drop or insert any object into any opening or hose.
• Do not use the product outdoors or operate where aerosol (spray) products are being used or a
room where it could be exposed to oxygen.
• Connect this product to a properly grounded outlet only. Refer to the Grounding Instructions in
the next pages of the manual.
SAFETY INFORMATION
(IMPORTANT SAFEGUARDS)
WARNING Failure to observe the following warnings may result in electric shock, fire,
personal injury, property damage or product damage.
CAUTION Failure to observe the following warnings may result in electric shock, fire,
personal injury, property damage or product damage.
SAVE THESE INSTRUCTIONS
5
SAFETY INFORMATION
(IMPORTANT SAFEGUARDS)
Ground GFCI Outlet
ATTENTION
This product should only be used with a grounded GFCI (Ground Fault
Circuit Interrupter) outlet and a grounded three-prong electrical cord
as shown to the right. In the event of an electrical short circuit, using a
grounded GFCI outlet reduces the risk of electric shock.
This product is equipped with a grounded cord and is for use on a
nominal 120V circuit only (minimum 15 amps) and must be plugged
into an outlet that is properly grounded with a GFCI breaker as shown.
Replace or repair a damaged cord immediately.
Test
Reset
Grounding Pin
IMPROPER USE OF THE GROUNDING PLUG CAN RESULT IN A RISK OF ELECTRIC SHOCK.
• If repair or replacement of the cord or plug is necessary, do not connect the grounding wire
to either flat blade terminal. The wire with green insulation (either with or without a yellow
stripe) is the grounding wire.
• Check with a qualified electrician if the grounding instructions are not completely understood,
or if there is doubt if the product is properly grounded.
For those with certain medical or mobility issues in the bathroom,
we recommend our Swash 1400 or Swash 1000 bidet seats, as their
mounting systems are engineered for the most secure transitions from
wheelchairs or walkers.
GROUNDING AND GFI OUTLET INSTRUCTIONS
SAVE THESE INSTRUCTIONS
6
Stainless-Steel Nozzle System
Stainless steel resists soiling and bacterial
contamination for enhanced hygiene.
Posterior and Feminine Warm Water Wash
Experience the ultimate in clean with adjustable
temperature, position, pressure, massage, and
oscillation settings.
Positionable Nozzle
The nozzle has five dierent positions
to ensure the most comfortable and
complete wash.
Adjustable Water Temperature and Pressure
Each wash mode (Front and Rear) has four
available water temperature settings, and five
water pressure settings.
Massage
When activated, the water pressure
automatically increases and decreases to
provide a pulsating, cleaning spray.
Warm Air Dryer
Includes adjustable temperature with five levels
for a hands-free experience and toilet paper
reduction – even elimination.
PRODUCT INFORMATION
Product Features
Nozzle Oscillation
The Move function provides a massaging,
oscillating cleanse during the wash cycle
ensuring a thorough and comfortable wash.
Auto Function
Activates a preset for a rear wash cycle
followed by a drying cycle.
Ergonomic Heated Seat
With four temperature settings
(High/Med/Low/O).
Illuminating Nightlight
The cool blue hue of the nightlight means no
more blinding lights during midnight trips to
the bathroom.
Gentle-Closing Seat and Lid
“Slam free” gentle closing seat and lid are
user friendly.
Eco Mode
When activated, this function automatically
lowers the water and seat temperature.
7
5.5 in
Required Distance Between Mounting Holes
18.2 in
18.2 in
14.9 in
14.9 in
7.8 in
7.8 in
2.7 in
2.7 in
16.4 in
15.2 in
13.6 in
13.6 in
4.3 in
4.3 in
Elongated Top View
Round Top View
PRODUCT INFORMATION
Product Dimensions
8
1. Lid
2. Seat Sensor
3. Warm Seat
4. Warm Air Dryer
5. Nozzle Assembly
6. LED Nightlight
7. Control Panel
8. Power Plug
9. Water Inlet with Mesh Filter
10. Drain Plug
11. Mounting Plate
9
 10
11
8
7
6
1
5
4
2
3
PRODUCT INFORMATION
Product Parts
9
1. Mounting Bolt (2)
2. Rubber Cone Washer (2)
3. Flat Washer (2)
4. Nuts (2)
5. Mounting Plate
6. Top-Mount Brackets (2)
7. T-Valve Connector with
Rubber Washer
8. Bidet Hose
PRODUCT INSTALLATION
Installation Parts
1
5
2
3
6
4
8
7
10
PRODUCT INSTALLATION
Before Installation
DO NOT PLUG THE PRODUCT IN WHILE THE UNIT IS UPSIDE DOWN
This may cause damage to the internal components.
WATCH OUR INSTALLATION VIDEO
Installation for all Swash products can be found online at brondell.com
CHECK BOLT SPREAD
This bidet seat can only be installed on toilets with a bolt hole spread of 14 cm / 5.5 in.
(see Product Dimensions on page 7 for more information).
CHECK FOR TOP MOUNT INSTALLATION
If your fixture only has top-side access to the mounting bolts that hold the seat to the toilet, use
the Top-Mount Brackets included in the hardware pack (see page 12).
CHECK FOR A CONCEALED TOILET FILL VALVE
Many modern toilets have sleek designs intended to cover and camouflage plumbing
connections, which makes a standard Swash installation dicult or impossible. For this, we
recommend using our Alternate Swash Bidet Seat T-Valve, found on brondell.com.
CHECK WATER SUPPLY LINE
Check the line that connects the toilet tank to the water shut o valve. If it is a rigid pipe, you may
need to purchase a flexible hose to replace it before installing the Swash. The length of the hose
and the size of the connectors will vary.
RESIDUAL MOISTURE IS NORMAL
Every product is tested with pure water during production to ensure the highest quality and
performance. It is normal to find a small amount of residual moisture on the product and in the
reservoir and filter.
TOOLS
A Phillips head or standard screwdriver may be needed to remove the existing toilet seat and a
standard wrench may be needed for tight water supply connections. Teflon tape can be helpful in
creating a water-tight seat between plumbing connections.
11
3. Connect the top of the T-Valve to the incoming water connection on
the bottom of your toilet tank.
4. Connect the water supply line coming from the wall to the bottom of
the T-Valve
5. Install Mounting Plate for Standard Installation
(see Page 12, Step 6 for instructions on using the Top-Mount Brackets)
a. Place adjustable mounting plate over mounting holes on toilet,
1. Existing Toilet Seat Removal
a. Lift hinge covers and use a screwdriver to remove the
mounting bolts.
b. Remove the toilet seat. Keep for future use.
2. Turn O Water Supply Valve and Flush Toilet
a. Turn water valve o to stop the flow of water.
b. Flush toilet and hold down handle to completely
empty tank.
c. Disconnect water supply hose from toilet tank. Do not
disconnect from the water supply valve.
rubber side facing down, arrow pointing to the toilet bowl.
b. Insert the mounting bolts through the mounting plate and
mounting holes of the toilet. Be sure that the square mounting
bolt head is even with the sides of the mounting plate.
PRODUCT INSTALLATION
Swash Installation
Please read these instructions carefully before installing the Swash.
Failure to do so could result in flooding, leaking or damage to the product.
NOTE: Steps may vary by type of seat and toilet
NOTES
You may wish to place a container under the tank to catch excess water.
Do not continue without completing the above steps
Failure to do so could result in flooding, leaking or damage to the Swash.
NOTES
The T-Valve connects to the fill valve directly under your toilet tank - it
does not connect at the wall.
Only connect to the cold toilet water supply line.
If your water supply line is rigid you may need to replace the water
supply line before continuing. Steps 3-4
Toilet tank
T-valve
Cold
water
supply
line
Step 2c
Steps 5b & 5c
12
6. Install Mounting Plate for top-mounted toilet seats (see Page 11,
Step 5 for instructions on Standard Installation). This method will
use a combination of the included Top-Mount Brackets and the
original toilet seat mounting bolts.
a. Place adjustable mounting plate over mounting holes on toilet,
rubber side facing down, arrow pointing to the toilet bowl.
b. Place the provided Top-Mount Brackets flat side
down into the slots of the Mounting Bracket, over the
bolt holes.
c. Insert the original toilet seat mounting bolts through the
Top-Mount Brackets and into the threaded bolt holes of the
toilet, using a screwdriver to tighten.
7. Connect the Bidet Hose to the Seat
a. Connect the elbow side of the bidet hose to the water inlet.
Hand-tighten to secure. Take care not to twist the bidet hose,
excessively bend it, or strip the plastic screw threads when
screwing the hose onto the bidet seat.
8. Attach the Swash to the Mounting Plate
a. Set the Swash flat on the toilet bowl in front of the mounting
plate, and slide seat onto plate until it is secure.
b. If the seat appears too short or too long for the toilet, adjust
the mounting plate accordingly. To adjust the mounting plate,
loosen the nuts underneath the toilet and slide seat forward
or backwards as needed. Once the seat is lined up properly,
tighten the nuts to hold in place.
NOTES: For those with mobility issues, we recommend our Swash 1400
or Swash 1000 bidet seats, as their mounting systems are engineered
for the most secure transitions from wheelchairs or walkers.
9. Connect the open end of the Bidet Hose to the T-Valve.
10. Turn On Water Supply
a. Open the main water supply valve slowly and check for leaks.
b. Wait 5 minutes, check again and if there are no leaks continue.
PRODUCT INSTALLATION
Swash Installation
c. Slide rubber cone washer, flat washer, and then nut onto
mounting bolts under the toilet bowl and tighten to keep
mounting plate in place.
Step 8b
Step 7a
Step 9
Steps 6b & 6c
13
NOTE: Make sure to only use a grounded GFCI (ground fault circuit
interrupter) electrical outlet. In the case of a short circuit, a grounded
GFCI outlet may help prevent electric shock or injury.
12. Press the “REAR WASH” button on the control arm to fill the
water tank. The bidet will beep continuously while it fills and
then issue one long beep when the water tank is full. Wait 3-5
minutes for the water to heat, and then the Swash will be ready
to use.
13. Follow instructions on Page 16 for using the Swash.
External Bidet Filter Installation
NOTE: Customers with hard water, well water, and softened water can extend the life of their
bidet seat by purchasing and installing an external inline water filter to be used with the Swash.
The bidet filter should be changed every six months, and can be purchased online at brondell.com.
11. Plug the Power Cord into an Electrical Outlet
a. If the Power Indicator is not illuminated press any button on
the control panel.
PRODUCT INSTALLATION
Swash Installation, External Bidet Filter Installation
1. Turn O Water Supply Valve and Flush Toilet.
a. Turn water valve o to stop the flow of water.
b. Flush toilet and hold down handle to completely empty tank.
2. Disconnect the Bidet Hose from the T-Valve
3. Connect the female end of the Swash Filter to the open T-Valve connection.
4. Connect the Bidet Hose to the male end of the Swash Filter.
5. Turn the toilet water supply valve back on.
Step 2
FLOW
Step 3
FLOW
Step 4
14
Water Temperature
Button and Indicators
Nozzle Position Buttons
Water Pressure and
Dry Temperature
Buttons and Indicators
Seat Temperature
Button and Indicators 9
8
   7
6
Eco Mode Button
and Indicator
Power Indicator
Auto Mode Button
Night Light Button
and Indicator
  10
  11
12
  13
1
3
4
2
Massage Button
Stop Button
Front Wash /
Move Button
Rear Wash /
Move Button
Warm Air Dry Button
5
OPERATING THE SWASH
SE400 Control Panel
15
1. Stop Button
Stops all wash and dry functions currently
operating. Press and hold this button for four
seconds to power o the bidet.
2. Rear Wash / Move Button
Press once to initiate a rear wash. Press
again to initiate nozzle oscillation (repetitive
forward and backward nozzle movement).
3. Front Wash / Move Button
Press once to initiate a front wash. Press
again to initiate nozzle oscillation (repetitive
forward and backward nozzle movement).
4. Dry Button
Press once to initiate a two minute Warm Air
Dryer cycle.
5. Massage Button
Pressing this button while a wash is running
enables the water to repeatedly increase
and decrease in pressure in a pulsating
pattern. Press again to stop the massage.
6. Water Pressure and Dry Temperature
Buttons and Indicators
Press the “+” and “–” buttons to increase
and decrease the outgoing water pressure
to one of five settings. Pressing these
buttons while the Warm Air Dryer is
operating will adjust the Drying temperature.
Settings will be saved for the next use.
7. Nozzle Position Buttons
Press the arrow up and arrow down buttons
to adjust the nozzle position forward and
backward during a wash cycle. Between
uses the nozzles will revert back to the
middle position.
8. Water Temperature Button and Indicators
Press and release the “Water Temp” button
to adjust the outgoing water temperature
to one of four settings (LO: 93.2° F, MED:
98.6° F, HI: 104° F, and OFF). Settings will be
saved for the next use.
9. Seat Temperature Button and Indicators
Press and release the “Seat Temp” button
to adjust the seat temperature to one of
four settings (LO: 95° F, MED: 100.4° F,
HI: 104° F, and OFF). Settings will be
saved for the next use.
10. Power Indicator
This indicator will light up when the bidet
is powered on, and will be o when the
bidet is powered o. To turn o the bidet
press and hold the “STOP” button for at
least four seconds.
11. Eco Mode Button and Indicator
Press and release the “Eco Mode”
button to select or turn o Eco Mode.
The indicator will light up when the Eco
Mode has been selected. See Page 17
for more information.
12. Night Light Button and Indicator
Press the “Night Light” button to enable
the Night Light (the indicator light will be
illuminated). Press again to disable the
Night Light and indicator.
13. Auto Mode Button
Press this button once to initiate a one
minute rear wash cycle followed by a
one minute dry cycle. See Page 17 for
more information.
OPERATING THE SWASH
SE400 Control Panel
16
Prepare for Wash
Sit on the seat to ensure skin-to-seat contact on
the Seat Sensor. Once contact is made the seat
will automatically perform many functions:
1. The seat will give an audible beep letting you
know the Seat Sensor has been engaged.
2. The water pressure indicator lights will come
on displaying the current setting.
3. If the bidet was set to Eco Mode, the seat
and water temperature will rise to the set
temperature settings.
NOTE: The wash functions will not work unless the sensor in the seat detects someone sitting down (with
the built-in skin conductivity sensor). To override the Seat Sensor, please see the instructions on Page 18.
OPERATING THE SWASH
Using the SE400
Warm Water Wash
When ready to wash, press the “Rear Wash”
or “Front Wash” button on the control panel
one time to initiate a wash. The nozzle will
self-clean, extend into the toilet bowl, spray
for two minutes, turn o automatically, retract,
and self-clean once again.
1. Pressing the “Rear” or “Front” button a
second time while the wash is running will
cause the nozzle to oscillate forward and
backward, providing a wider range of
wash spray. Press again to cancel the
move function.
2. While washing, users can adjust the water
temperature, pressure, and nozzle position
settings, as well as initiate the massage
feature by following the notes on Page 15.
3. If you would like to stop the wash before
the two minute cycle ends, press the
“Stop” button to discontinue water flow.
4. After extended use the water may
decrease in temperature if a LOW,
MEDIUM, or HIGH water temperature
setting is selected. To regain warmer water,
stop all wash functions for three minutes to
allow the bidet to reheat the water.
17
NOTE: All wash and dry settings are adjustable,
while the Auto Mode wash cycle is running, to
suit your preferences
OPERATING THE SWASH
Using the SE400
Warm Air Dryer Function
Press the “Dry” button to activate the warm air
dryer. The dryer will run for two minutes and
turn o automatically.
1. While the air dryer is operating, users
can adjust the dryer temperature to a
comfortable level using the Dry “+” and
–” buttons. The dry temperature will be
reflected on the five indicator LEDs.
2. If you would like to stop the dryer before the
two minutes has elapsed, press Stop.
Auto Mode
Pressing the “Auto Mode” button will initiate
a one-minute Rear Wash with the following
parameters preset:
Seat Temperature set to Medium
Nozzle Oscillation (Move) on
Water Pressure set to Level 3
Water Temperature set to Medium
After the wash cycle is over, Auto Mode
will initiate a one-minute Warm Air Dry cycle
on Level 2.
Eco Mode
In this mode the water in the tank and the seat
temperature will be heated to 86°F when the
bidet is not in use. Once a person sits on the
bidet the Swash will revert to the last seat and
water temperature settings used. To select
this option press and release the “Eco Mode”
button to illuminate its indicator.
18
Seat Sensor Override
The Seat Sensor is activated at the factory by default. Completing the
following steps will bypass the body sensor located in the seat and allows
the wash functions and dry functions to operate without the sensor being
engaged. Use caution in this mode.
1. Unplug the Swash bidet seat.
2. Press the two Water Pressure/Dry Temp buttons (+ and –) and plug the seat
in while holding the two buttons down.
3. Keep holding the two Water Pressure/Dry Temp buttons (+ and –) down for
five seconds. A beep will sound, indicating that the Seat Sensor has been
overridden. To test that the procedure worked, press the Dry button. If
the Warm Air Dryer comes on without anyone sitting on the seat, you have
successfully overridden the Seat Sensor.
4. You can resume using the seat as normal.
5. To reactivate the Seat Sensor, repeat Steps 1-3.
Activating/Deactivating Silent Mode
By default, the Swash will beep to confirm commands from the control panel.
Follow the steps below to silence the beeping sounds.
1. Press and hold down the Rear Wash/Move button and the “–” Water
Pressure/Dry Temp button at the same time for four seconds.
2. A beep will sound, indicating that the Silent Mode has been activated.
3. To deactivate Silent Mode, repeat Steps 1-2.
NOTE: Do not sit on the seat when in Special Mode Operations. The process will
not work while the seat is occupied.
OPERATING THE SWASH
Special Mode Operations
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84

brondell Swash SE400 Le manuel du propriétaire

Taper
Le manuel du propriétaire