brondell IS707-EW Manuel utilisateur

Taper
Manuel utilisateur

Ce manuel convient également à

OWNER’S MANUAL
Swash IS707 Advanced Bidet Toilet Seats
IS707-EW
IS707-RW
Attach Proof of Purchase to This Page
Adjunte prueba de compra a esta página
Joindre une preuve d’achat à cette page
1
CONTENTS
This manual contains important safety information. Before operating the
bidet, please read this manual thoroughly, and retain it for future reference.
PRODUCT INSTALLATION
GENERAL INFO
PRODUCT OPERATION
02 SAFETY INFORMATION
06
06
07
08
PRODUCT INFORMATION
Product Features
Product Dimensions
Product Parts
09
09
10
10
13
PRODUCT INSTALLATION
Installation Parts
Before Installation
Swash Installation
External Bidet Filter Installation
14
14
16
18
OPERATING THE SWASH
IS707 Control Panel
Using the Swash IS707
Special Mode Operations
TECHNICAL INFO
TRANSLATIONS
19 PRODUCT SPECIFICATIONS
20
20
20
21
21
MAINTENANCE
Seat Cleaning & Removal
Nozzle Cleaning
Cleaning the Mesh Filter
Product Storage & Use
22 TROUBLESHOOTING
25 WARRANTY
26 CONTACT
1 ENGLISH
27 SPANISH
54 FRENCH
2
Failure to observe the following warnings may result in electric shock, fire, personal injury, property
damage or product damage:
Do not use a damaged power plug or plug into a loose electric outlet.
Do not move the product by pulling the power cord.
Do not handle the product or power plug with wet hands.
Do not forcefully bend the power cord or place heavy objects on it to prevent it from being damaged
or deformed.
Do not connect and pull out the power plug or cord repeatedly.
Unplug the product before cleaning, repairing, inspecting, or replacing parts.
Remove any dust or water from the power plug prior to plugging in.
Do not plug the product into an electrical outlet or power strip that is being used by too many other
products. Use an electrical outlet adequate for the wattage of the product rated for a minimum of 15
amps.
If the power cord is damaged, do not attempt to repair, modify, or replace the cord yourself. Contact
the Brondell Service Center toll free at 888-542-3355 or email us through our website.
If the product produces a strange noise, a burning smell, or emits smoke, unplug it immediately
from the electrical outlet and contact Brondell. Failure to do so may result in electric shock or fire.
Do not insert any wires or sharp objects into any product gaps. This may result in electric shock, fire,
or product damage.
Be careful to keep this safety information. Please read this information
to prevent property loss and ensure safety.
SAFETY INFORMATION
IMPORTANT SAFEGUARDS
DANGER:
If not observed, serious injury or even death may occur as a result.
DANGER
WARNING:
If not observed, serious physical injury or property damage may occur as a result.
CAUTION:
If not observed, minor physical injury or property damage may occur as a result.
READ ALL INSTRUCTIONS BEFORE USING
SAVE THESE INSTRUCTIONS
3
Do not place an electronic or gas heater near the product or dispose of any burning materials
such as a lit cigarette in the toilet. This may result in fire or product deformation. Do not place any
containers filled with water or other liquids, food, metallic objects, or any flammable material on top
of the product. If foreign material enters the product, this may result in electric shock or fire.
Do not use the product in locations exposed to excessive moisture and do not splash water onto the
product.
While cleaning the bathroom, pull the power plug out of the electrical outlet and exercise caution to
ensure that water or cleaning supplies do not splash onto the bidet. Failure to do so may result in
electric shock or fire.
If foreign material enters the product, pull the power plug out of the electrical outlet, turn o the
main water valve, and call the Brondell Service Center.
Do not disassemble, repair, or modify the product yourself.
Do not use the product while wet from bathing or showering.
Do not place or store the product where it can fall or be pulled into a tub or sink.
Do not place in or drop the product into water or any other liquid.
Do not reach for the product if it has fallen into water. Unplug the product immediately and call the
Brondell Service Center.
Do not use the product if it is not working properly. Please unplug the product immediately, close
the main water supply valve, and call the Brondell Service Center at 888-542-3355. Failure to do so
may result in electric shock, fire, or flooding.
SAFETY INFORMATION (cont.)
IMPORTANT SAFEGUARDS
DANGER
SAVE THESE INSTRUCTIONS
Failure to observe the following warnings may result in electric shock, fire, personal injury, property
damage or product damage.
Do not plug in, operate, or store the unit in locations where flammable or combustible materials are
used or kept.
Do not use industrial water, or gray water for the supply, as this may cause skin damage or disease.
Turn o the main water supply valve when cleaning.
For children and seniors who may have diculties with adjusting temperatures or those with sen-
sitive skin or impaired heat sensitivity, set the temperature of the wash spray and seat to “low” or
“o” to prevent burning.
Close supervision is necessary when this product is used by children, seniors, or persons requiring
general assistance.
Do not press the buttons using excessive force.
Do not stand on top of or place any heavy objects onto the seat cover.
Use this product for its intended use only, as described in this manual. Do not use any attachments
that are not recommended by Brondell.
WARNING
4
SAFETY INFORMATION (cont.)
IMPORTANT SAFEGUARDS
SAVE THESE INSTRUCTIONS
Failure to observe the following warnings may result in electric shock, fire, personal injury, property
damage, or product damage.
Do not connect the main water supply to the hot water pipe or supply (only connect to the cold
water supply).
After the installation, make sure to check all water supply connections for leaks. Rubber washers
should be in place for the water connection hoses & T-Valve.
Do not open/close the seat or seat cover with excessive force.
Exercise caution that urine does not come into contact with the product - failure to do so may result
in bad odors or malfunction.
If the product will not be used for a long period of time, unplug the power cord, close the main
water supply valve, and drain any water in the water tank.
Do not pull out the bidet hose using excessive force.
Do not use thinner, benzene, acidic chemicals, chloride, or hydrochloric acid detergent on or near
the product. This may result in corrosion to the metal parts or discoloration or scratches to the bidet
body.
This appliance is not intended for use by persons (including children and seniors) with reduced
physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have
been given supervision or instruction concerning the use of the appliance by a person responsible
for their safety.
Children should be supervised to ensure that they do not play with the appliance.
CAUTION
WARNING
Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has
been dropped or damaged, or dropped into water. Contact the Brondell Service Center for examina-
tion and repair.
Keep the cord away from heated surfaces and heating vents.
Never block the air openings of the product or place it on a soft surface, such as a bed or couch,
where the air openings may be blocked. Keep the air openings free of lint, hair, etc.
Never drop or insert any object into any opening or hose.
Do not use the product outdoors or operate where aerosol (spray) products are being used or a
room where it could be exposed to oxygen.
Connect this product to a properly grounded outlet only. Refer to the Grounding Instructions in the
next pages of the manual.
5
This product should only be used with a grounded GFCI
(Ground Fault Circuit Interrupter) outlet and a grounded
three-prong electrical cord as shown to the right. In the
event of an electrical short circuit, using a grounded GFCI
outlet reduces the risk of electric shock.
This product is equipped with a grounded cord and is for
use on a nominal 120V circuit only (minimum 15 amps) and
must be plugged into an outlet that is properly grounded
with a GFCI breaker as shown. Replace or repair a damaged
cord immediately.
Extension Cord Use
If it is necessary to use an extension cord, only use those rated for a minimum of 15 amps with a
three-wire extension cord with a three-blade grounding plug. Only plug into a three-slot grounded
GFCI receptacle that will accept the plug of the product. Replace or repair any damaged cords
immediately.
GROUNDING AND GFI OUTLET INSTRUCTIONS
Test
Reset
Ground GFCI Outlet
Grounding Pin
Improper use of the grounding plug can result in a risk of electric shock.
If repair or replacement of the cord or plug is necessary, do not connect the
grounding wire to either flat blade terminal. The wire with green insulation
(either with or without a yellow stripe) is the grounding wire.
Check with a qualified electrician if the grounding instructions are not completely
understood, or if there is doubt if the product is properly grounded.
SAFETY INFORMATION (cont.)
IMPORTANT SAFEGUARDS
SAVE THESE INSTRUCTIONS
6
PRODUCT INFORMATION
Stainless-Steel Nozzle System - Stainless steel resists soiling and bacterial contamination for
enhanced hygiene.
Posterior and Feminine Warm Water Wash – experience the ultimate in clean with adjustable
temperature, position, pressure, massage, and oscillation settings.
Positionable Nozzle – the nozzle has five dierent positions to ensure the most comfortable and
complete wash.
Adjustable Water Temperature and Pressure – each wash mode (Front and Rear) has four
available water temperature settings, and five water pressure settings.
Massage – when activated, the water pressure automatically increases and decreases to provide a
pulsating, cleaning spray.
Warm Air Dryer – includes adjustable temperature with five levels for a hands-free experience and
toilet paper reduction – even elimination.
Nozzle Oscillation – the Move function provides a massaging, oscillating cleanse during the wash
cycle ensuring a thorough and comfortable wash.
Auto Function – activates a preset for a rear wash cycle followed by a drying cycle.
Ergonomic Heated Seat – with four temperature settings (High/Med/Low/O).
Illuminating Nightlight – the cool blue hue of the nightlight means no more blinding lights during
midnight trips to the bathroom.
Gentle-Closing Seat and Lid – “slam free” gentle closing seat and lid are user friendly.
Eco Mode – when activated, this function automatically lowers the water and seat temperature.
PRODUCT FEATURES
7
PRODUCT DIMENSIONS
5.5 in
Required Distance Between
Mounting Holes
18.2 in
18.2 in
14.9 in
14.9 in
7.8 in
7.8 in
2.7 in
2.7 in
16.4 in
15.2 in
13.6 in
13.6 in
4.3 in
4.3 in
Elongated Top View
Round Top View
8
PRODUCT PARTS
PRODUCT INFORMATION (cont.)
1. Lid
2. Seat Sensor
3. Warm Seat
4. Warm Air Dryer
5. Nozzle Assembly
6. LED Nightlight
7. Control Panel
8. Power Plug
9. Water Inlet with Mesh Filter
10. Drain Plug
11. Mounting Plate
8
9
10
7
6
1
11
5
4
2
3
9
INSTALLATION PARTS
1. Mounting Bolt (2)
2. Rubber Cone Washer (2)
3. Flat Washer (2)
4. Nuts (2)
5. Mounting Plate
1
5
2
3
6
4
6. Top-Mount Brackets (2)
7. T-Valve Connector with
Rubber Washer
8. Bidet Hose
8
7
PRODUCT INSTALLATION
10
DO NOT PLUG THE PRODUCT IN WHILE THE UNIT IS UPSIDE DOWN
This may cause damage to the internal components.
WATCH OUR INSTALLATION VIDEO
Installation for all Swash products can be found online at brondell.com
CHECK BOLT SPREAD
This bidet can only be installed on toilets with a bolt hole spread of 5.5 inches (see Product
Dimensions on Page 7 for more information).
CHECK FOR TOP MOUNT INSTALLATION
If your fixture only has top-side access to the mounting bolts that hold the seat to the toilet,
include the Top-Mount Brackets included in the hardware pack (see Page 12).
CHECK FOR A CONCEALED TOILET FILL VALVE
Many modern toilets have sleek designs intended to cover and camouflage plumbing
connections, which makes a standard Swash installation dicult or impossible. For this, we
recommend using our Alternate Swash Bidet Seat T-Valve, found on brondell.com.
CHECK WATER SUPPLY LINE
Check the line that connects the toilet tank to the water shut o valve. If it is a rigid pipe, you may
need to purchase a flexible hose to replace it before installing the Swash. The length of the hose
and the size of the connectors will vary.
RESIDUAL MOISTURE IS NORMAL
Every product is tested with pure water during production to ensure the highest quality and
performance. It is normal to find a small amount of residual moisture on the product and in the
reservoir and filter.
TOOLS
A Phillips head or standard screwdriver may be needed to remove the existing toilet seat and a
standard wrench may be needed for tight water supply connections. Teflon tape can be helpful in
creating a water-tight seat between plumbing connections.
PRODUCT INSTALLATION (cont.)
BEFORE INSTALLATION
SWASH INSTALLATION
1. Existing Toilet Seat Removal
a. Lift hinge covers and use a screwdriver to remove the mounting bolts.
b. Remove the toilet seat. Keep for future use.
Please read these instructions carefully before installing the Swash. Failure to do so could result
in flooding, leaking or damage to the product.
11
NOTE: Steps may vary by type of seat and toilet
SWASH INSTALLATION (cont.)
3. Connect the top of the T-Valve to the incoming water
connection on the bottom of your toilet tank.
4. Connect the water supply line coming from the wall to the
bottom of the T-Valve
5. Install Mounting Plate for Standard Installation (see
Page 12, Step 6 for instructions on using the Top-Mount
Brackets)
a. Place adjustable mounting plate over mounting holes
on toilet, rubber side facing down, arrow pointing to the
toilet bowl.
b. Insert the mounting bolts through the mounting plate
and mounting holes of the toilet. Be sure that the
square mounting bolt head is even with the sides of the
mounting plate.
c. Slide rubber cone washer, flat washer, and then nut
onto mounting bolts under the toilet bowl and tighten to
keep mounting plate in place.
NOTES:
The T-Valve connects to the fill valve directly under
your toilet tank - it does not connect at the wall.
Only connect to the cold toilet water supply line.
If your water supply line is rigid you may need to
replace it before continuing.
Steps 5b & 5c
Steps 3-4
toilet tank
t-valve
cold water
supply line
NOTES:
You may wish to place a container under the tank to
catch any excess water.
Do not continue without completing the above steps
Failure to do so could result in flooding, leaking or
damage to the Swash.
2. Turn O Water Supply Valve and Flush Toilet
a. Turn water valve o to stop the flow of water.
b. Flush toilet and hold down handle to completely
empty tank.
c. Disconnect water supply hose from toilet tank. Do not
disconnect from the water supply valve.
Step 2c
12
PRODUCT INSTALLATION cont.
SWASH INSTALLATION (cont.)
9. Connect the open end of the Bidet Hose to the T-Valve.
8. Attach the Swash to the Mounting Plate
a. Set the Swash flat on the toilet bowl in front of the
mounting plate, and slide seat onto plate until it is
secure.
b. If the seat appears too short or too long for the toilet,
adjust the mounting plate accordingly. To adjust the
mounting plate, loosen the nuts underneath the toilet
and slide seat forward or backwards as needed. Once
the seat is lined up properly, tighten the nuts to hold in
place.
7. Connect the Bidet Hose to the Seat
a. Connect the elbow side of the bidet hose to the water
inlet. Hand-tighten to secure. Take care not to twist the
bidet hose, excessively bend it, or strip the plastic screw
threads when screwing the hose onto the bidet seat.
11. Plug the Power Cord into an Electrical Outlet
a. If the Power Indicator is not illuminated press any
button on the control panel.
10. Turn On Water Supply
a. Open the main water supply valve slowly and check
for leaks.
b. Wait 5 minutes, check again and if there are no leaks
continue.
Step 8b
Step 7a
Step 9
6. Install Mounting Plate for top-mounted toilet seats (see
Page 11, Step 5 for instructions on Standard Installation).
This method will use a combination of the included Top-
Mount Brackets and the original toilet seat mounting bolts.
a. Place adjustable mounting plate over mounting holes
on toilet, rubber side facing down, arrow pointing to the
toilet bowl.
b. Place the provided Top-Mount Brackets flat side down
into the slots of the Mounting Bracket, over the bolt
holes.
c. Insert the original toilet seat mounting bolts through the
Top-Mount Brackets and into the threaded bolt holes of
the toilet, using a screwdriver to tighten.
Steps 6b & 6c
13
SWASH INSTALLATION (cont.)
NOTES:
Make sure to only use a grounded GFCI (ground fault circuit interrupter) electrical outlet. In
the case of a short circuit, a grounded GFCI outlet may help prevent electric shock or injury.
If it is necessary to use an extension cord, only use those rated for a minimum of 15 amps
with a three-wire extension cord with a three-blade grounding plug.
12. Press the “REAR WASH” button on the control arm to fill the water tank. The bidet will beep
continuously while it fills and then issue one long beep when the water tank is full. Wait 3-5
minutes for the water to heat, and then the Swash will be ready to use.
13. Follow instructions on Page 16 for using the Swash.
EXTERNAL BIDET FILTER INSTALLATION
1. Turn O Water Supply Valve and Flush Toilet.
a. Turn water valve o to stop the flow of water.
b. Flush toilet and hold down handle to completely empty tank.
2. Disconnect the Bidet Hose from the T-Valve
3. Connect the female end of the Swash Filter to the open T-Valve connection.
4. Connect the Bidet Hose to the male end of the Swash Filter.
5. Turn the toilet water supply valve back on.
Step 2
FLOW
Step 3
FLOW
Step 4
NOTE:
Customers with hard water, well water, and softened water can extend the life of their bidet
seat by purchasing and installing an external inline water filter to be used with the Swash.
The bidet filter should be changed every six months, and can be purchased online at
brondell.com.
14
OPERATING THE SWASH
IS707 CONTROL PANEL
Water Temperature
Button and Indicators
Nozzle Position Buttons
Water Pressure and
Dry Temperature
Buttons and Indicators
Seat Temperature
Button and Indicators
9
8
7
6
Eco Mode Button
and Indicator
Power Indicator
Auto Mode Button
Night Light Button
and Indicator
10
11
12
13
1
3
4
2
Massage Button
Stop Button
Front Wash /
Move Button
Rear Wash /
Move Button
Warm Air Dry Button
5
15
IS707 CONTROL PANEL (cont.)
1. Stop Button
Stops all wash and dry functions currently operating. Press and hold this button for four
seconds to power o the bidet.
2. Rear Wash / Move Button
Press once to initiate a rear wash. Press again to initiate nozzle oscillation (repetitive forward
and backward nozzle movement).
3. Front Wash / Move Button
Press once to initiate a front wash. Press again to initiate nozzle oscillation (repetitive forward
and backward nozzle movement).
4. Dry Button
Press once to initiate a two minute Warm Air Dryer cycle.
5. Massage Button
Pressing this button while a wash is running enables the water to repeatedly increase and
decrease in pressure in a pulsating pattern. Press again to stop the massage.
6. Water Pressure and Dry Temperature Buttons and Indicators
Press the “+” and “–” buttons to increase and decrease the outgoing water pressure to one of
five settings. Pressing these buttons while the Warm Air Dryer is operating will adjust the Drying
temperature. Settings will be saved for the next use.
7. Nozzle Position Buttons
Press the arrow up and arrow down buttons to adjust the nozzle position forward and backward
during a wash cycle. Between uses the nozzles will revert back to the middle position.
8. Water Temperature Button and Indicators
Press and release the “Water Temp” button to adjust the outgoing water temperature to one of
four settings (LO: 93.2° F, MED: 98.6° F, HI: 104° F, and OFF). Settings will be saved for the
next use.
9. Seat Temperature Button and Indicators
Press and release the “Seat Temp” button to adjust the seat temperature to one of four settings
(LO: 95° F, MED: 100.4° F, HI: 104° F, and OFF). Settings will be saved for the next use.
10. Power Indicator
This indicator will light up when the bidet is powered on, and will be o when the bidet is
powered o. To turn o the bidet press and hold the “STOP” button for at least four seconds.
11. Eco Mode Button and Indicator
Press and release the “Eco Mode” button to select or turn o Eco Mode. The indicator will light
up when the Eco Mode has been selected. See Page 17 for more information.
12. Night Light Button and Indicator
Press the “Night Light” button to enable the Night Light (the indicator light will be illuminated).
Press again to disable the Night Light and indicator.
13. Auto Mode Button
Press this button once to initiate a one minute rear wash cycle followed by a one minute dry
cycle. See Page 17 for more information.
16
OPERATING THE SWASH cont.
USING THE SWASH IS707
Warm Water Wash
When ready to wash, press the “Rear Wash” or “Front Wash” button on the control panel one time
to initiate a wash. The nozzle will self-clean, extend into the toilet bowl, spray for two minutes,
turn o automatically, retract, and self-clean once again.
1. Pressing the “Rear” or “Front” button a second time while the wash is running will cause the
nozzle to oscillate forward and backward, providing a wider range of wash spray. Press again
to cancel the move function.
2. While washing, users can adjust the water temperature, pressure, and nozzle position settings,
as well as initiate the massage feature by following the notes on Page 15.
3. If you would like to stop the wash before the two minute cycle ends, press the “Stop” button to
discontinue water flow.
4. After extended use the water may decrease in temperature if a LO, MEDIUM, or HI water
temperature setting is selected. To regain warmer water, stop all wash functions for three
minutes to allow the bidet to reheat the water.
Prepare for Wash
Sit on the seat to ensure skin-to-seat contact on the Seat Sensor. Once contact is made the seat
will automatically perform many functions:
1. The seat will give an audible beep letting you know the Seat Sensor has been engaged.
2. The water pressure indicator lights will come on displaying the current setting.
3. If the bidet was set to Eco Mode, the seat and water temperature will rise to the set
temperature settings.
Warm Air Dryer Function
Press the “Dry” button to activate the warm air dryer. The dryer will run for two minutes and turn
o automatically.
1. While the air dryer is operating, users can adjust the dryer temperature to a comfortable level
using the Dry “
+”
and “–” buttons. The dry temperature will be reflected on the five indicator
LEDs.
2. If you would like to stop the dryer before the two minutes has elapsed, press Stop.
NOTES:
The wash functions will not work unless the sensor in the seat detects someone sitting
down (with the built-in skin conductivity sensor). To override the Seat Sensor, please see
the instructions on Page 18.
17
USING THE SWASH IS707 (cont.)
Auto Mode
Pressing the “Auto Mode” button will initiate a one-minute Rear Wash with the following
parameters preset:
Seat Temperature set to Medium
Nozzle Oscillation (Move) on
Water Pressure set to Level 3
Water Temperature set to Medium
After the wash cycle is over, Auto Mode will initiate a one-minute Warm Air Dry cycle on Level 2.
Note: All wash and dry settings are adjustable, while the Auto Mode wash cycle is running, to suit
your preferences
Eco Mode
In this mode the water in the tank and the seat temperature will be heated to 86°F when the
bidet is not in use. Once a person sits on the bidet the Swash will revert to the last seat and water
temperature settings used. To select this option press and release the “Eco Mode” button to
illuminate its indicator.
18
OPERATING THE SWASH cont.
SPECIAL MODE OPERATIONS
Seat Sensor Override
The Seat Sensor is activated at the factory by default. Completing the following steps will bypass
the body sensor located in the seat and allows the wash functions and dry functions to operate
without the sensor being engaged. Use caution in this mode.
1. Unplug the Swash bidet seat.
2. Press the two Water Pressure/Dry Temp buttons (+ and –) and plug the seat in while holding
the two buttons down.
3. Keep holding the two Water Pressure/Dry Temp buttons (+ and –) down for five seconds.
A beep will sound, indicating that the Seat Sensor has been overridden. To test that the
procedure worked, press the Dry button. If the Warm Air Dryer comes on without anyone
sitting on the seat, you have successfully overridden the Seat Sensor.
4. You can resume using the seat as normal.
5. To reactivate the Seat Sensor, repeat Steps 1-3.
NOTE:
Do not sit on the seat when in Special Mode Operations. The process will not work while
the seat is occupied.
Activating/Deactivating Silent Mode
By default, the Swash will beep to confirm commands from the control panel. Follow the steps
below to silence the beeping sounds.
1. Press and hold down the Rear Wash/Move button and the “–” Water Pressure/Dry Temp button
at the same time for four seconds.
2. A beep will sound, indicating that the Silent Mode has been activated.
3. To deactivate Silent Mode, repeat Steps 1-2.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84

brondell IS707-EW Manuel utilisateur

Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues