brondell FS-10 Le manuel du propriétaire

Owner’s Manual FS-10/FreshSpa

Table of Contents

Product Features ................Page 2

Parts List ........................Page 3

Conguration ...................Page 4

Installation .....................Page 5

Operation ......................Page 9

Maintenance ....................Page 10

Warranty .......................Page 11

Contact .........................Page 13

FreshSpa Feature List:

Hygienic retractable nozzle

Self cleaning nozzle feature

Ambient temperature bidet wash

Nozzle positioning (3 settings)

Adjustable water pressure

All brass internal valve

High quality metal 7/8” T-valve

High quality braided metal hose

Anti-bacterial ABS material with full body panel

Backow prevention valve

No electricity or batteries required

Easy installation and adjustable toilet t

All accessories included for standard installation

1 year warranty

2

Parts List

3

1 ea small rubber washer

Bidet attachment

with turn dial control

Adjustable brackets

T-valve connector Bidet hose

2 ea large rubber washers

1 ea small rubber

washer with raised lip

4

Conguration

5

Installation

Before Installation:

Check Water Supply Line: Check the water supply line that

connects the toilet tank ll valve to the water shuto valve at

the wall. If it is a rigid pipe, you will need to purchase a exible

water supply hose to replace it before installing the FreshSpa.

The length of the hose may vary and the top connection size

should be 7/8” Ballcock to connect to the T-valve that you will

install under the toilet tank and the bottom connection will vary

(most common are 3/8” and1/2”female compression).

1) Remove existing toilet seat

a. Lift hinge covers and use athead or Phillips head screwdriver

to remove the mounting bolts. Alternatively, you may need to

loosen mounting bolts underneath the seat.

b. Remove the toilet seat and set the seat, mounting bolts and

hardware aside.

2) Turn o water supply valve and

ush toilet

a. Turn o water supply at the wall to

stop ow of water.

b. Flush toilet and hold down handle

to completely empty toilet tank.

c. Disconnect water supply hose from

the ll valve under the toilet tank.

3) Connect 7/8” T-Valve to Water

Supply Line and Fill Valve Under

Toilet Tank.

a.Install the 7/8” T-valve with the

small rubber washer with raised lip

to the incoming water connection on

the bottom of your toilet tank. Be sure

to place the at edge of the rubber

washer into the T-Valve against the

metal with the raised lip facing the

toilet tank connection.

b. Connect the cold water supply line

coming from the wall to the bottom

of the T-valve using the small at

rubber washer (if needed).

Step 2a

Installation

6

Step 2c

Step 3a & 3b

4) Connect Bidet Hose to T-Valve

a. Connect one end of the metal Bidet

Hose to the remaining open side of

the installed 7/8” T-valve.

5) Install Bidet Attachment on Toilet

a. Place large rubber washers over the

open bolt holes in the toilet xture.

b. Place bidet attachment over

washers so the nozzle is as close to

the back of the toilet bowl as it will go.

This will vary by toilet.

c. Make sure the adjustable brackets

line up with the holes in the toilet

xture. You may need to move the

adjustable brackets accordingly to

line up properly.

d. Replace the toilet seat on top of

bidet attachment and secure using

original toilet seat hardware. Make

sure to tighten so that the bidet

attachment and seat do not move.

Step 5

Installation

7

6) Connect Bidet Hose to Bidet Attachment

a. Connect open end of bidet hose to the

brass connection on the bottom side of

the bidet attachment.

7) Turn on Water Supply & Check for Leaks

a. Open the main water supply valve slowly and check for

leaks.

b. Wait 5-10 minutes, check again and if there are no leaks

continue.

Note: if there is any leaking, check all rubber washers and make

sure all water connections are tight and secure. If necessary,

you can use plumbers tape for any leaking connections.

Installation

Step 6a

8

Operation

Using the FreshSpa

To clean the bidet nozzle, turn the control dial towards the “Nozzle

Cleaning” position and water should wash over the nozzle.

For the general bidet wash function, turn the dial towards the

“Wash” position.

• The further the dial is turned, the higher the water pressure will be.

• To lower the water pressure, turn the nozzle back towards the center.

For a front wash function, women may need to tilt & bend forward

slightly in order for the spray to hit the appropriate areas.

1

2

3

Nozzle positioning

There are 3 dierent nozzle

positions that you can easily

adjust by gently pulling the

end of the nozzle forward

or backwards. Once desired

position is set, the nozzle will

remain in that position until

manually moved.

9

Maintenance

To clean the nozzle, gently pull down on the head of the nozzle, and

use a toothbrush or soft cloth and mild detergent (such as dish soap)

to clean the nozzles. You may also unscrew the nozzle tip cap for a

more thorough cleaning or use a toothpick if any nozzle holes are

plugged with hard water buildup.

To clean the bidet, use a mild cleaner such as Simple Green or Windex

spray to clean the FreshSpa. Do not scrub or use harsh, abrasive

products to clean the FreshSpa, which may scratch the product.

10

Warranty

Brondell products are backed by some of the most comprehensive warranties

in the industry. Brondell warrants that the FreshSpa shall be free from defects

in material and workmanship under normal use and service.

FreshSpa One-Year Limited Warranty

100% Coverage of all parts and labor for the entire product for the rst year

from original date of purchase

Exclusions and Limitations

1. BRONDELL warrants its products to be free from manufacturing defects under

normal use and service. This warranty is extended only to the ORIGINAL PURCHASER.

2. BRONDELL’s obligations under this warranty are limited to repairs or replacement,

at BRONDELL’s option, of products or parts found to be defective, provided that

such products were properly installed and used in accordance with instructions.

BRONDELL reserves the right to make such inspections as may be necessary in order

to determine the cause of the defect. BRONDELL will not charge for labor or parts in

connection with warranty repairs for the rst full year from date of purchase on all

products except those that may be subject to commercial use limitations.

3. BRONDELL is not responsible for the cost of removal, return (shipping) and/or

reinstallation of products. This warranty does NOT apply to:

Damage or loss which occurs during shipment.

Damage or loss sustained through any natural or manmade causes beyond the

control of BRONDELL, including but not limited to re, earthquake, oods, etc.

Damage or loss resulting from sediments or foreign matter contained in a water system.

Damage or loss resulting from negligent or improper installation including

installation of a unit in a harsh or hazardous environment.

Damage or loss resulting from removal, improper repair, modication of the

product, or improper maintenance including damage caused by chlorine or

chlorine related products.

Damage or loss resulting from acts which are not the fault of Brondell or which

the Product is not specied to tolerate.

11

Warranty

4. This warranty gives you specic legal rights. You may have other rights which vary

from state to state.

THIS WRITTEN WARRANTY IS THE ONLY WARRANTY MADE BY BRONDELL. REPAIR

OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY SHALL BE THE EXCLUSIVE

REMEDY AVAILABLE TO THE PURCHASER. BRONDELL SHALL NOT BE RESPONSIBLE

FOR LOSS OF USE OF THE PRODUCT OR FOR OTHER INCIDENTAL, SPECIAL, FOR

CONSEQUENTIAL DAMAGES OR EXPENSES INCURRED BY THE PURCHASER OR FOR

LABOR OR OTHER COSTS DUE TO INSTALLATION OR REMOVAL OR COSTS OF REPAIRS

BY OTHERS, OR FOR ANY OTHER EXPENSE NOT SPECIFICALLY STATED ABOVE. EXCEPT

TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES,

INCLUDING THAT OF MERCHANTABILITY, ARE EXPRESSLY LIMITED TO THE DURATION

OF THIS WARRANTY. SOME STATES DO NOT ALLOW LIMITATIONS, SO THE ABOVE

LIMITATION AND EXCLUSION MAY NOT APPLY TO YOU.

How to Obtain Service

To obtain repair service under this warranty, you must contact an authorized

BRONDELL Service Center to obtain an RMA (Return Merchandise Authorization)

number. Proof of purchase in the form of a copy of your original receipt must

accompany the returned unit for the warranty to be valid. Take or ship the unit pre-

paid to the closest Brondell authorized service center along with your RMA number

and proof of purchase.

To obtain your RMA number and locate the BRONDELL Service Center location

nearest you, call 1-888-542-3355.

12

Contact

For questions, contact

Brondell Customer Service:

1-888-542-3355

Brondell, Inc.

PO Box 470085

San Francisco, CA 94147-0085

Phone: 1-888-542-3355

Email: [email protected]

Web: www.brondell.com

13

Manual del propietario

Características del producto .....Página 2

Lista de piezas ..................Página 3

Conguración ..................Página 4

Instalación ......................Página 5

Funcionamiento ................Página 9

Mantenimiento .................Página 10

Garantía ........................Página 11

Contacto…………………………Página 13

bidé fácil

Lista de características:

Boquilla higiénica retráctil

Función de autolimpieza de la boquilla

Lavado de bidé a temperatura ambiente

Posicionamiento de la boquilla (3 posiciones)

Presión de agua adaptable

Válvula interna toda realizada en bronce

Válvula T de 7/8 in toda realizada en bronce

Manguera de metal trenzado de alta calidad

Material ABS antibacterial con panel completo

Válvula de no retorno

No requiere energía eléctrica ni baterías

Fácil instalación y ajustable al inodoro

Todos los accesorios para una instalación estándar incluidosño

1 año de garantía

2

Lista de piezas

3

Accesorio para el bidé

con perilla de control

Soportes ajustables

Conector de válvula T Manguera de bidé

Unión de goma

grande de 2 ea

Unión de goma

pequeña de uno

Unión de goma con

reborde pequeña de uno

Conguration

4

Asiento de

inodoro

Pernos

Bidé

Manguera

de bidé

7/8" Conector

de válvula T

Tuercas

Inodoro

La page charge ...

brondell FS-10 Le manuel du propriétaire

Ce manuel convient également à

brondell FS-10 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents