Ruwido 827A Mode d'emploi

Marque: Ruwido

Modèle: 827A

Taper: Mode d'emploi

Ce manuel convient également à

827A01 Remote Control

2855-001 remote control user guide

model 827A01

date: 2020-12-14

version: 1

modification, communication to third parties and any other use is strictly prohibited without prior written accordance of ruwido.

ruwido_userguide_2855-001_model827A01_2020-12-14.docx page 2 of 5

table of content

1 user operating instructions ................................................................. 3

1.1 manual pairing ...................................................................................... 3

1.2 LED behavior ......................................................................................... 3

1.3 factory reset ......................................................................................... 3

2 declaration.......................................................................................... 4

modification, communication to third parties and any other use is strictly prohibited without prior written accordance of ruwido.

ruwido_userguide_2855-001_model827A01_2020-12-14.docx page 3 of 5

1 user operating instructions

1.1 manual pairing

- power on STB

- press “play/pause” and “home” keys for 3 seconds to start

pairing process (continuous red LED flashing)

 LED will stop flashing red if pairing was successful

- to delete pairing from remote control press “skip back” and

“skip forward” keys for 3 seconds to delete pairing

 LED will flash 4 times red if pairing deletion was successful

1.2 LED behavior

- LED will flash red when BLE command is transmitted

- LED will flash green when IR command is transmitted

1.3 factory reset

- to set remote control back to factory mode press and hold “apps” + “left” key

for a minimum of 3 seconds

 LED will flash 4 times red

modification, communication to third parties and any other use is strictly prohibited without prior written accordance of ruwido.

ruwido_userguide_2855-001_model827A01_2020-12-14.docx page 4 of 5

2 declaration

User Information FCC 15.2:

Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

Part 15 Statement. FCC 15.19/RSS Gen Issue 3 Sect. 7.1.3

This device complies with Part 15 of the FCC Rules and with Industry Canada license-

exempt RSS standard(s). Operation is subject to the following two conditions: (1) this

device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils

radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1)

l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter

tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en

compromettre le fonctionnement.

Statement Class B Digital Device FCC 15.105:

NOTE: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

 Consult the dealer or an experienced radio/ TV technician for help.

ruwido austria gmbh

Koestendorfer Str. 8 . 5202 Neumarkt . Austria . t +43 6216 4571-0 .

[email protected]m . www.ruwido.com

Ruwido 827A Mode d'emploi

Marque: Ruwido

Modèle: 827A

Taper: Mode d'emploi

Ce manuel convient également à

827A01 Remote Control

Télécharger le PDF

rapport

dans d''autres langues

English: Ruwido 827A User guide

Ruwido 827A Mode d'emploi

Ce manuel convient également à

Ruwido 827A Mode d'emploi

dans d''autres langues

Autres documents