Ruwido 827A01 Remote Control Mode d'emploi

827A01 Remote Control
Ruwido
Marque
Ruwido
Modèle
827A01 Remote Control
Taper
Mode d'emploi

Ce manuel convient également à

2855-001 remote control user guide
model 827A01
date: 2020-12-14
version: 1
copyright 2020 ruwido austria gmbh - this document is the intellectual property of ruwido austria gmbh and contains information. reproduction,
modification, communication to third parties and any other use is strictly prohibited without prior written accordance of ruwido.
ruwido_userguide_2855-001_model827A01_2020-12-14.docx page 2 of 5
table of content
1 user operating instructions ................................................................. 3
1.1 manual pairing ...................................................................................... 3
1.2 LED behavior ......................................................................................... 3
1.3 factory reset ......................................................................................... 3
2 declaration.......................................................................................... 4
copyright 2020 ruwido austria gmbh - this document is the intellectual property of ruwido austria gmbh and contains information. reproduction,
modification, communication to third parties and any other use is strictly prohibited without prior written accordance of ruwido.
ruwido_userguide_2855-001_model827A01_2020-12-14.docx page 3 of 5
1 user operating instructions
1.1 manual pairing
- power on STB
- press “play/pause” and “home” keys for 3 seconds to start
pairing process (continuous red LED flashing)
LED will stop flashing red if pairing was successful
- to delete pairing from remote control press “skip back” and
“skip forward” keys for 3 seconds to delete pairing
LED will flash 4 times red if pairing deletion was successful
1.2 LED behavior
- LED will flash red when BLE command is transmitted
- LED will flash green when IR command is transmitted
1.3 factory reset
- to set remote control back to factory mode press and hold “apps” + “left” key
for a minimum of 3 seconds
LED will flash 4 times red
copyright 2020 ruwido austria gmbh - this document is the intellectual property of ruwido austria gmbh and contains information. reproduction,
modification, communication to third parties and any other use is strictly prohibited without prior written accordance of ruwido.
ruwido_userguide_2855-001_model827A01_2020-12-14.docx page 4 of 5
2 declaration
User Information FCC 15.2:
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Part 15 Statement. FCC 15.19/RSS Gen Issue 3 Sect. 7.1.3
This device complies with Part 15 of the FCC Rules and with Industry Canada license-
exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
Statement Class B Digital Device FCC 15.105:
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/ TV technician for help.
ruwido austria gmbh
Koestendorfer Str. 8 . 5202 Neumarkt . Austria . t +43 6216 4571-0 .
[email protected]m . www.ruwido.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Ruwido 827A01 Remote Control Mode d'emploi

827A01 Remote Control
Ruwido
Marque
Ruwido
Modèle
827A01 Remote Control
Taper
Mode d'emploi
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Autres documents