Bercomac 700574-1 Manuel utilisateur

1

48’’ SNOW BLADE

WITH ELECTRIC LIFT

For

THE MAJORITY OF TRACTORS BY H.O.P. (2005 AND AFTER)

CRAFTSMAN HUSQVARNA, ARIENS, DIXON, POULAN, WEEDEATER

CAUTION:

READ & FOLLOW ALL SAFETY RULES & INSTRUCTIONS BEFORE

OPERATING YOUR EQUIPMENT

M-07

*106582*

106582_EN

OWNER’S MANUAL

Model Number

700574-1 Snow Blade 48’’

2

LIMITED WARRANTY

Bercomac Limitée

92, Fortin North, Adstock, Quebec, Canada, G0N 1S0

Conditions and Products Covered:

BERCOMAC guarantees any part of the product or accessory

manufactured by BERCOMAC and found in the reasonable

judgment of BERCOMAC to be defective in material and or

workmanship will be repaired or replaced by an authorized

dealer without charge up to our maximum labor rates and pre-

established times. For replacement parts only standard ground

freight services are covered. This warranty extends to the

original retail purchaser only and is not transferable to any

subsequent purchasers.

Warranty Period

(from date of the original retail purchase)

 Residential use: 1 year

 Semi-commercial, professional or rental use: 90 days

Exceptions Noted Below; the following items are guaranteed

by the original manufacturer and have their own warranty,

conditions and limited time:

 Tire Chains: 90 days

 Engines: Will vary as per the manufacturer

Please refer to the engine manufacturer’s warranty

statement included with the unit. BERCOMAC is not

authorized to handle warranty adjustments on engines.

Items and Conditions NOT Covered:

This warranty does not cover the following:

 Pick-up or delivery charges or in-home services fees.

 Any damage or deterioration of the unit, parts and or finish

of these due to normal use, wear and tear, or exposure.

 Cost of regular use or maintenance service or parts, such as

gas, oil, lubricants, tune-up parts, and adjustments.

 Any part or accessory which has been altered, modified,

misused, neglected, accidentally damaged or not properly

installed, maintained, stored or repaired not in accordance

with the instructions in the owner’s manual.

 Repair due to normal wear and or any wear items such as

shear pins, bolts, belts, etc.

 Expedited freight fee services for replacement parts.

 Shear bolts and shear pins are to be considered as a

preventive measure not as an assured protection, any

damages resulting from the lack of shear bolts breakage are

not covered.

NOTE: All warranty work must be performed by an authorized

dealer using original (manufacturer) replacement parts.

Owner’s Responsibilities:

BERCO’s defective equipment or part must be returned to an

Husqvarna dealer or an authorized BERCO dealer within the

warranty period for repairs. In the event that defective

merchandise must be returned to manufacturer for repairs,

freight fees are prepaid and a written authorization from

BERCOMAC must be obtained by dealer prior to the

shipment. This warranty extends only to equipment operated

under normal conditions. To validate a warranty claim, it is the

user’s responsibility to maintain and service the unit as

specified in the owner’s manual or to have the unit serviced at

their dealer at their expense.

General Conditions:

The sole liability of BERCOMAC with respect to this warranty

shall be strictly and exclusively repair and replacement as

mentioned herein. BERCOMAC shall not have any liability for

any other costs, loss or damage, including but not limited to,

any incidental or consequential loss or damage.

In particular, without being limited to, BERCOMAC shall have

no liability or responsibility for:

 Travel time, overtime, after hours time or other

extraordinary repair charges or relating to repairs and or

replacements outside of normal business hours.

 Rental of like or similar replacement equipment during the

period of any, repair or replacement work.

 Any communicating or travel charges.

 Loss or damage to person or property other than that

covered by the terms of this warranty.

 Any claims for lost revenue, lost profit or any similar costs

as a result of damage or repair.

 Attorney’s fees.

BERCOMAC’s responsibility in respect to claims is limited to

making the required repairs or replacement without charge up

to our maximum labor rates and pre-established times and no

claim of breach of warranty shall be cause for cancellation or

rescission of the contract of sale of any product or accessory.

This warranty gives you specific legal rights. You may also

have other rights, which vary from state to state.

NOTE: Bercomac reserves the right to change or improve the design of any part or accessory without assuming any obligation to modify

any product previously manufactured.

Instructions for Obtaining Warranty Services:

Contact your local Husqvarna authorized dealer or any other BERCO service dealer to arrange service at their dealership. To locate a

BERCO dealer convenient to you, access our website at www.bercomac.com. Don't forget to bring your proof of purchase (sales

receipt) for repairs.

1

TABLE OF CONTENTS

INTRODUCTION ...................................................................................................................................................... 2

SAFETY PRECAUTIONS ........................................................................................................................................ 3

SAFETY DECALS .................................................................................................................................................... 5

ASSEMBLY

Tools Required ........................................................................................................................................... 6

Step 1: Subframe Installation ..................................................................................................................... 7

Step 2: Installation the Winch Control Switch ............................................................................................ 10

Step 3: Snow Blade Preparation ............................................................................................................... 13

Step 4: Snow Blade Installation ................................................................................................................. 15

OPERATION

Controls ....................................................................................................................................................... 16

Raising or Lowering the Snow Blade ........................................................................................................ 16

Adjusting the Angle of the Snow Blade ..................................................................................................... 16

Trip Spring System ..................................................................................................................................... 16

MAINTENANCE, DISMOUNTING & STORAGE

Maintenance ............................................................................................................................................... 17

Snow Blade Dismounting ........................................................................................................................... 17

Storage ........................................................................................................................................................ 17

Verify Tire Pressure .................................................................................................................................... 17

TROUBLESHOOTING ............................................................................................................................................. 18

PARTS BREAKDOWN AND PARTS LIST

Snow Blade ................................................................................................................................................. 19

Subframe ..................................................................................................................................................... 21

TORQUE SPECIFICATION TABLE ....................................................................................................................... 24

ATTACHMENTS ....................................................................................................................................................... 25

PAGE

2

INTRODUCTION

TO THE PURCHASER

This new accessory was carefully designed to give years of dependable service. This manual has been provided to

assist in the safe operation and servicing of your attachment.

NOTE: All photographs and illustrations in the manual may not necessarily depict the actual models or attachment, but

are intended for reference only and are based on the latest product information available at the time of publication.

Familiarize yourself fully with the safety recommendations and operating procedures before putting the machine to

use. Carefully read, understand and follow these recommendations and insist that they be followed by those who will

use this attachment.

THIS SAFETY ALERT SYMBOL IDENTIFIES AN IMPORTANT SAFETY MESSAGE IN THIS

MANUAL THAT HELPS YOU AND OTHERS AVOID PERSONAL INJURY OR EVEN DEATH.

DANGER, WARNING, AND CAUTION ARE SIGNAL WORDS USED TO IDENTIFY THE LEVEL OF

HAZARD. HOWEVER, REGARDLESS OF THE HAZARD, BE EXTREMELY CAREFUL.

DANGER: Signals an extreme hazard that will cause serious injury or death if recommended precautions

are not followed.

WARNING: Signals a hazard that may cause serious injury or death if the recommended precautions are

not followed.

CAUTION: Signals a hazard that may cause minor or moderate injury if the recommended precautions are

not followed.

Record your attachment serial number and purchase date in the section reserved below (there is no serial number on

the subframe). Your dealer requires this information to give you prompt, efficient service when ordering replacement

parts. Use only genuine parts when replacements are required.

If warranty repairs are required please present this registration booklet and original sales invoice to your selling dealer

for warranty service.

This manual should be kept for future reference.

Please check if you have received all the parts for your kit with the list of the

bag and the list of the box.

SERIAL NUMBER : ___________________________

(IF APPLICABLE)

MODEL NUMBER: ___________________________

PURCHASE DATE : ___________________________

3

SAFETY PRECAUTIONS

Careful operation is your best insurance against an accident. Read this section carefully before operating the vehicle

and accessory. This accessory is capable of amputating hands and feet and throwing objects. Failure to observe the

following safety instructions could result in serious injury. All operators, no matter how experienced they may be,

should read this and other manuals related to the vehicle and accessory before operating. It is the owner's legal

obligation to instruct all operators in safe operation of the accessory.

GLOSSARY:

In this manual, right and left sides are determined by

sitting on the seat of the vehicle facing forward.

In this manual, "accessories" means attachments

(snowblower, rotary broom, blade etc.) that you install

on the vehicle (lawn tractors, A.T.V. s etc).

TRAINING:

This symbol, "Safety Alert Symbol", is used

throughout this manual and on the

accessory’s safety labels to warn of the

possibility of serious injury. Please take

special care in reading and understanding

the safety precautions before operating the

vehicle and accessory.

1. Read this owner's manual carefully. Be thoroughly

familiar with the controls and proper use of the

vehicle and accessory. Know how to stop the unit

and disengage the controls quickly.

2. Never allow children to operate the vehicle nor the

accessory. Never allow adults to operate the vehicle

nor the accessory without proper instructions.

3. No one should operate the vehicle nor the

accessory while intoxicated or while taking

medication that impairs the senses or reactions.

4. Keep the area of operation clear of all people,

particularly small children and pets.

PREPARATION:

1. Thoroughly inspect the area where the accessory

is to be used and remove door mats, all foreign

objects and the like.

2. For motorized accessories, disengage all clutches

and shift into neutral before starting engine.

3. Do not operate the accessory without wearing

adequate winter outer garments. Avoid loose fitting

clothing that can get caught in moving parts. Wear

footwear that will improve footing on slippery

surfaces.

4. Handle fuel with care, it is highly flammable.

a) Use approved fuel container.

b) Never add fuel to a running engine or hot engine.

c) Fill fuel tank outdoors with extreme care. Never fill

fuel tank indoors.

d) Never fill containers inside a vehicle, or on a

truck or a trailer bed with a plastic liner. Always

place containers on the ground, away from your

vehicle, before filling.

e) When practical, remove gas-powered

equipment from the truck or trailer and refuel it

on the ground. If this is not possible, then refuel

such equipment on a trailer with a portable

container, rather than from a gasoline

dispenser nozzle.

f) Keep the nozzle in contact with the rim of the

fuel tank or container opening at all times, until

refueling is complete. Do not use a nozzle lock-

open device.

g) Replace fuel cap securely and wipe up spilled

fuel.

h) If fuel is spilled on clothing, change clothing

immediately.

5. Never attempt to make any adjustments while the

engine (motor) is running (except when specifically

recommended by manufacturer).

6. Let the vehicle and accessory adjust to outdoor

temperatures before using.

7. Never use an accessory without proper guards,

plates, or other safety protective devices in place

8. Always make sure to wear the appropriate safety

equipment required (glasses, muffs, mask…) for

each type of product. See operation section.

9. Always make sure of having safe traction on the

vehicle by using the recommended accessories

(chains, A.T.V. tracks, counterweights…). See

operation section.

10. Always make sure the all components are correctly

installed. (driveline securely attached and locked at

both ends, belts properly installed…)

11. Always handle the winch cable with thick leather

gloves.

12. Never modify the accessory or any part without

the written consent from the manufacturer.

4

OPERATION:

1. Do not put hands or feet near, under or inside rotating

parts.

2. Exercise extreme caution when operating on or

crossing gravel drives, walks or roads. Stay alert for

hidden hazards or traffic. Do not carry passengers.

3. After striking a foreign object, stop the engine (motor),

disconnect the wire from the spark plug(s) and keep

wire away to prevent accidental starting. Thoroughly

inspect the accessory for any damage and repair

damage before restarting and using the accessory.

4. If the unit should start to vibrate abnormally, stop the

engine (motor) and check immediately for the

cause. Vibration is generally a warning of trouble.

5. Take all possible precautions when leaving the

vehicle unattended. Disengage the power take-off,

lower the attachment, place the transmission into

neutral, set the parking brake, stop the engine and

remove the contact key.

6. Do not run the engine indoors, except when starting

the engine and for transporting in or out of the

building. Do not operate or let motor run in a storage

area without ventilation because gas contains

carbon monoxide which is odorless, colorless and

can cause death.

7. Never use the accessories across the face of

slopes, go from top to bottom. Exercise extreme

caution when using equipment on slopes. Do not

attempt to clear a steep slope.

8. Never tolerate bystanders in the working zone.

Never use an accessory in the direction of

bystanders, it might throw gravel or debris that can

hurt people or damage property.

9. Never operate the accessory at high transport

speeds on slippery surfaces. Use care when

backing up.

10. Do not carry passengers.

11. Disengage power to the accessory when it is

transported or not in use.

12. Never operate the accessory without good visibility

or light.

13. Keep the accessory away from heat sources or

flames.

14. Never handle the winch cable or hook while in

tension.

MAINTENANCE AND STORAGE

1. When cleaning, repairing or inspecting the vehicle

and accessory, make certain that all moving parts

have stopped. For gasoline engine, disconnect wire

from the spark plug(s) and keep wire away to

prevent accidental starting.

2. Check all the bolts and components at frequent

intervals to make sure that they are properly

tightened.

3. Never store a motorized accessory with fuel in the

fuel tank inside a building where ignition sources are

present such as hot water and space heaters,

clothes dryers, and the like. Allow the engine to cool

before storing in any enclosure.

4. Always refer to the owner’s manual when you store

the accessory and vehicle for a prolonged or an

unspecified length of time.

5. Maintain or replace safety and instruction labels, as

necessary.

6 For winter accessories, (if applicable), let the engine

run for a few minutes after clean snow in order to

prevent the rotary parts from freezing.

7. Inspect the vehicle’s and accessory’s air filter (if

applicable) every day. Clean it or replace it as

necessary. Change the oil more often when working

in dusty conditions. See the vehicle’s and

accessory's owner’s manual.

THIS SYMBOL MEANS

DANGER !

BECOME ALERT !

YOUR SAFETY IS INVOLVED !

SAFETY PRECAUTIONS

5

REPLACE IF DECALS ARE DAMAGED

SEE PARTS BREAKDOWN FOR DECAL LOCATION

SAFETY DECALS

DECAL #105130

Before installing or using:

Locate, read and make sure to understand all of the

owner’s manual.

DECAL #105133

Failure to observe these instructions could lead to

severe injury or death.

To avoid injury to hands or fingers:

-Always keep hands clear of rope hook loop, ,hook and

fairlead opening during installation , operation and

when spooling in or out.

-Always use extreme caution when handling hook and

rope during spooling operations.

-Always wear heavy leather gloves when handling rope.

-Keep hands away from the hot surface.

6

ASSEMBLY

IMPORTANT: TORQUE ALL BOLTS ACCORDING

TO TORQUE SPECIFICATION TABLE WHEN

STATED: TIGHTEN FIRMLY.

THE WINCH KIT IS TO BE USED ONLY TO LIFT

BERCO ACCESSORIES, ANY OTHER USE MAY

CAUSE DAMAGE TO THE VEHICLE.

This subframe may be used to install different

attachments (see attachments page). Once installed,

it may remain permanently on your vehicle.

NOTE:It is not necessary to remove mower deck at

this step.

TOOLS REQUIRED:

Wrenches: 3/4’’ 5/16, 7/16, 9/16, 1/2, 10mm

Ratchet

Sockets: 9/16, 1/2

Pliers

1 cutting pliers

Square head screwdriver: #2

1 flat screwdriver

1 wrench (for the nuts on the battery posts of the

vehicle)

Optional tools according to the year of the

vehicle:

Drill

Bit: 13/32

Punch

Hammer

Please sort out and identify all the hardware before

starting installation. Lists for the hardware bag and

for the box are supplied in each.

INSTALLING THE REFLECTORS

IMPORTANT: When operating the tractor with the

front mounted attachment, install the two red-colored

adhesive reflectors on the rear vertical surface of the

tractor’s fender.

Before starting the subframe installation, verify if your

has a tractor heat shield as shown (A-1).

If not, go to the instructions on next page.

A-1

A-2

If the tractor has this shield, you must remove it and

install the new one included in this kit (See picture

below (A-2).

NOTE: If the original heat shield is bolted to the front

of tractor frame, detach the top part (item 1) of the

heat shield (item 2) that is supplied by folding it up

and down along the dotted line.

Be careful not to cut yourself on the sharp edges. For

your safety sand down the sharp edges.

Use the tractor bolts to secure in place.

7

Install the supports

Install the supports (item 5) on each side of the

vehicle.

Item # Description Action

1 Carriage bolt,

3/8 x 1’’ (qty 6)

Insert as shown.

2 Carriage bolt,

5/16 x 1’’ (qty 2)

Insert as shown.

*3 Flat washer 1/2’’,

(qty 6)

See*

4 Flat washer 7/16’’,

(qty 2)

Insert on

carriage bolt

(item 2)

5 Support

(qty 2)

Install on the

bolts as shown.

6 Flange nut 3/8’’,

(qty 6)

Do not tighten

now.

7 Flange nut 5/16’’,

(qty 2)

Do not tighten

now.

*For tractors with a engine mounting plate use only

two washers. Do not use washer A.

*For tractors without an engine mounting plate use all

three washers.

STEP 1

SUBFRAME INSTALLATION:

Refer to parts breakdown section for parts

identification.

8

ASSEMBLY

Install the female hitch between the two supports

Install the female hitch (item 1)

# Item Description Action

1 Female hitch Install between the

two supports.

2 Hex bolt 3/8 x 1’’

(qty 4)

Insert as shown.

3 Flange nut 3/8’’

(qty 4)

Tighten the all the

nuts firmly.

Install the spring (item 1)

# Item Description Action

1 Spring Install the spring

on the frame as

shown.

NOTE: The latch must move freely.

Install the spring as shown

9

ASSEMBLY

NOTE: Use these same instructions for both

sides of tractor.

Manual Clutch: Install the new belt guides (item A)

that are included with the drive mechanism on the

bottom carriage bolt (item 1). Place a 1/2’’ flat washer

(items B & C) over the belt guide and the top carriage

bolt. Continue with the handle support installation.

NOTE: When using the blade only, the drive

mechanism is not necessary. Install the left

handle and right cab supports over the original

tractor belt guides by using the bottom bolt only.

Electric Clutch: Do not install belt guides. Place a

1/2’’ flat washer (item B) over the bottom carriage

bolt. Continue with the handle support (left side)

installation and cab support (right side).

Install the handle support (item 2) on the left side and

the cab support on the right side as shown.

# Item Description Action

1 Carriage bolt

3/8 x 1’’ (qty 4)

Insert the bolts as

shown.

2 Handle / cab support Install as shown.

**3 Thread cutting screw

3/8 x1’’

See **

4 Flat washer 3/8’’

(qty 4)

Install as shown.

5 Flange nut 3/8’’

(qty 4)

Tighten the nuts.

6 Square head set

screw 5/16 x 1/2’’

Insert in the hole of

the handle.

7 Plastic grommet Insert as shown.

** Use this screw if the bottom hole is threaded.

Install the handle support on left side

Install the cab support on right side

10

ASSEMBLY

Install the winch control switch

STEP 2:

INSTALLATION OF THE WINCH CONTROL

SWITCH

Install the relay (item 1).

#

Item

Description Action

1 Relay Install in an appropriate

area.

2 Metal screw

#12 x 3/4’’ (qty 4)

Secure relay in place.

*3 Nylon tie wrap 8’’

(qty 4)

See *

*If necessary use the nylon tie wraps to secure the

relay in place.

** Install in a sheltered place away from bad weather.

Install the relay

IMPORTANT

To prolong the winch cable’s life, release the winch control switch as soon as the accessory touches the

ground. This will keep the cable from tangling up which causes premature wear.

Before drilling the hole, check behind the dashboard

to make sure there is enough space to install the

switch.

Drill a 1/2’’ hole in the dashboard or an appropriate

place (see reference drawing). Stick the UP/DOWN

decal over the hole for the switch.

Insert the switch in the hole and secure in place with

the rubber boot.

NOTE: It is important to install the switch vertically.

Connect the wires as shown.

When the switch is raised, the winch must lift the

accessory. If you prefer the contrary, invert the green

and black wires.

Connect the wires

Up / Down decal

11

ASSEMBLY

CONNECTING THE WIRES

NOTE:The posts on the relay are identified by

numbers. (1-2-3-4).

Install the wires from the winch on the posts of the

relay.

Red wire (+) on post #3.

Black wire (-) on post #4.

Connect the red wire from the winch (limit switch) with

the green wire from the relay.

Connect the wires

IDENTIFY THE IGNITION WIRE:

Place the clip of the Hi / Low tester on the negative

post (-) on the battery or a metal surface without any

paint.

Turn the ignition key to the position: Accessory.

Insert the tip of the tester in a hole at the back of the

starter (switch) make sure to touch the metal part of

the wire (on most tractors, it is the A1 terminal on the

ignition switch that is used for accessories. Before

connection, verify with HI/LOW tester).

If the tester’s light turns on, turn the ignition key to the

position, Off. The light must turn off.

You have identified the ignition wire, if not repeat the

operation on another wire.

INSTALL THE CONTROL WIRE:

Join the ignition wire and the red wire from the winch

control (item 1) with the instant connector (item 2).

Connect the black wire of the winch control (item 3) to

the black wire on the relay.

Connect the green wire of the winch control (item 3)

with the red wire of the winch (limit switch).

Connect the ignition wire

12

ASSEMBLY

CAUTION

FOR YOUR SECURITY:

Read and follow the safety precautions for the

battery in the vehicle’s manual.

CONNECT THE WIRES ON THE BATTERY:

Connect the wires from the relay to the vehicle’s

battery.

The red wire (+) on the positive post of the battery

(item 1).

The black wire (-) on the negative post of the battery

(item 2).

Make sure to tighten the nuts on the posts.

TIE ALL THE WIRES:

NOTE: Make sure the wires from the control

assembly do not interfere with anything on the tractor

nor come into contact with any heating, electrical or

removable elements of the tractor.

Tie the wires with four nylon tie wraps included in the

kit.

Connect the relay wires to the battery

Install the heat shield

VERY IMPORTANT:

Make sure the cable winds up and unrolls as shown

in the figure (cable under the spool). Lubricate the

winch cable and drum with grease.

If the winch cable does not wind up from the

bottom of spool as shown, the limit switch will not

work and may cause damage to the subframe,

winch and accessory.

Install the heat shield (item 1).

# Item Description Action

1 Heat shield Install as shown.

2 Hex bolts 1/4 x 1/2’’

(qty 2)

Tighten firmly.

NOTE: If the tractor has a front muffler, install the

heat shield (item 3) using the two bolts (item 4)

which holds the winch on the frame.

13

ASSEMBLY

Install the push frame (item 1) and the skid shoes (item

6).

Item # Description Action

1 Push frame Install under the

attaching frame

(item A) as shown.

2 Hex. bolt 1/2 x 2’’ Insert as shown.

3 Flat washer 9/16’’

(qty 2)

Insert as shown.

*4 Nylon insert lock nut

1/2’’

See *

5 Carriage bolt

5/16’’ x 3/4’’ (qty 4)

Insert as shown.

6 Skid shoes (qty 2) Install on bolts as

shown.

7 Flange nut 5/16’’

(qty 4)

Tighten firmly.

NOTE: Remove the nylon tie wrap that holds the latch.

*Do not tighten too much so that the push frame moves

freely.

Overall view

STEP 3

SNOW BLADE PREPARATION:

Refer to parts breakdown section for parts

identification.

Install push frame and skid shoes.

14

ASSEMBLY

Install the control rod (item 3)

Item # Description Action

1 Joint block Install on latch

as shown.

2 Retaining ring Insert on the

end of the latch

as shown.

3 Control rod Insert in the joint

block as shown.

4 Hair pin 2.5mm Secure the

control rod.

IMPORTANT: When the latch is in the unlocked

position, it must rest on the head of the bolt.

Install control rod

Prepare handle (item 3).

Item # Description Action

1 Hand grip Install on handle

as shown.

2 Hair pin 2.5mm Insert in the

handle .

Store these parts safely until you install the snow

blade.

Prepare handle

15

INSTALLATION

STEP 4

SNOW BLADE INSTALLATION:

You must install the subframe before continuing

with snow blade installation.

WARNING

TO PREVENT INJURIES:

Stop the motor.

Apply parking brake.

Remove the ignition key.

Disconnect the wire from the spark plug(s) and

keep away from spark plug(s) to prevent accidental

starting.

Attach the snow blade to the subframe as shown.

Make sure the snow blade is pushed in until locked

into place by the latch (item 1).

Hook the winch cable (item 2) on the hook (item3) on

the push frame.

Familiarize yourself with the winch control and make

sure the cable stays wrapped from the bottom of the

drum of the winch.

Lift and lower the snow blade using the switch.

Install the handle (item 2)

Item # Description Action

1 Hair pin 2.5mm Remove from

handle.

2 Handle Insert in handle

support.

3 Control rod Insert in handle

and secure with

the hair pin.

Install the blade in the latch

16

OPERATION

WARNING

Read the tractor Owner’s Manual carefully. Be

thoroughly familiar with the controls & proper

use of the attachment.

RAISING OR LOWERING THE SNOW

BLADE:

Familiarize yourself with the winch control.

Lift and lower the snow blade using the switch.

ADJUSTING THE ANGLE OF THE SNOW

BLADE:

The handle that allows to adjust the angle of the snow

blade is located on the left hand side of the tractor, close

to the steering wheel. To adjust the angle, turn the

handle counter-clockwise to unlock the latch. Push or

pull the handle to adjust the blade to the desired angle.

TRIP SPRING SYSTEM:

The snow blade was designed to topple forward when

striking solid objects. Once the blade clears the

obstacle, it will spring back to its normal operating

position, therefore, protecting the operator and tractor

from any impacts that might occur.

IMPORTANT:

THE WINCH KIT IS TO BE USED ONLY TO LIFT

BERCO ACCESSORIES, ANY OTHER USE MAY

CAUSE DAMAGE TO THE VEHICLE.

CONTROLS

IMPORTANT:

In order to avoid damage to the battery of the

vehicle, always start the engine before using the

winch.

THE WINCH CONTROL SWITCH

Press on the winch control switch to lift or lower the

accessory to the ground.

There is a limit switch stopper that limits the lifting.

To prolong the winch cable’s life, release the winch

control switch as soon as the accessory touches the

ground. This will keep the cable from tangling up,

causing premature wear of the cable.

17

MAINTENANCE & DISMOUNTING & STORAGE

WARNING

TO PREVENT INJURIES:

Stop the motor.

Apply parking brake.

Remove the ignition key.

Disconnect the wire from the spark plug(s) and

keep away from spark plug(s) to prevent accidental

starting.

MAINTENANCE:

1) Verify the mounting bolts at frequent intervals for

proper tightness in order to prevent costly repairs.

Make sure that your equipment is in safe working

condition.

2) Lubricate all pivoting points.

3) To prolong the life span of the winch, make sure the

snap mount switch which limits the lift height works

well.

4) To prolong the winch cable’s life, release the

winch control switch as soon as the accessory

touches the ground. This will keep the cable from

tangling up, causing premature wear of the cable.

STORAGE

a) Clean thoroughly and repaint all parts from which

paint has worn.

b) List the replacement parts that will be needed to

be replaced before the next season.

c) Store the snow blade in a dry place.

d) Apply oil at all pivot points

Refer to parts breakdown section for parts

identification.

VERIFY TIRE PRESSURE:

Check and adjust tractor tire pressure as follows:

Front tires: 14-15 psi

Back tires: 7-8 psi

Tire pressure must be even on both sides of the

tractor.

WINCH CABLE MAINTENANCE

To reduce the risk of cable failure during the season,

we recommend changing the winch cable every year.

Install the new winch cable as shown in figure in the

parts breakdown.

SNOW BLADE DISMOUNTING:

1) Straighten and lower the snow blade. Remove the

hair pin from the handle and remove the handle.

2) Detach the snow blade by activating the latch of

the female hitch.

3) Remove the rear counterweight when you remove

the front attachment (if applicable).

4) You may leave the subframe on tractor all year long

or remove it if preferred.

5) Reinstall mower if needed.

18

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION

Winch runs backwards. Winch wires reversed. Recheck wiring.

Switch wires reversed. Recheck wiring.

Switch installed incorrectly. Check switch installation.

Battery wires reversed. Recheck wiring.

Winch cable is not winded up from

the bottom of spool.

Wind winch cable from underneath.

Winch will not operate or runs in

one direction only.

Vehicle’s ignition switch is at OFF

position.

Turn vehicle’s ignition switch at ON

position.

Broken wires or bad connection. Check for poor connections.

Control switch is inoperative. Replace control switch.

Relay or breaker is damaged. Replace the relay or breaker.

Limit switch is damaged. Replace limit switch.

Winch is damaged. Replace or repair winch.

Winch runs but with insufficient

power or line speed.

Weak battery. Recharge or replace battery.

Check charging system.

Poor battery connection. Check battery terminals for

corrosion. Clean when required.

Winch is damaged. Replace or repair winch.

* Please refer to parts breakdown section in subframe manual for parts identification.

HOW TO KNOW POINTS TO CHECK

Poor connections. Recheck wiring with the owner's manual.

HI/LOW voltage tester does not work. Connect it on battery posts (+ and -) of a functional battery.

If there is no light, the tester is damaged.

The control switch inoperative. Test both connectors with HI/LOW voltage tester.

If light comes ON in both positions (IN & OUT), the switch is

operative.

Relay is damaged When it is working, there is a "CLICK" sound when the control switch

is activated. Check connections with HI / LOW voltage tester.

Winch is damaged The ultimate test is to connect the winch directly to the battery and

reverse the wires to test both directions. If the winch doesn't work, it is

damaged.

The limit switch is damaged. When the limit switch is pushed or stuck inside, the winch can't raise

the accessory, only lower it. If not replace it.

The breaker is damaged. Check the voltage on both terminals on the breaker with the HI / LOW

voltage tester. If not replace.

La page charge ...

Bercomac 700574-1 Manuel utilisateur

Bercomac 700574-1 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents