YUNEEC ST12 Manuel utilisateur

YUNEEC
Marque
YUNEEC
Modèle
ST12
Taper
Manuel utilisateur

Ce manuel convient également à

User Manual
Product: Radio Controller
Model No.: ST12
Brand Name: YUNEEC
INTRODUCTION
The ST12 is equipped with a touch screen display that allows for changing
various settings and viewing real-time telemetry data and streaming video
during flight. The ST12 seamlessly integrates control of the camera so you can
easily take still photos and start/stop video recording using the corresponding
buttons.
OPERATING INSTRUCTIONS:
ST12 AND RECEIVER BINDING
STEP 1): Power on the ST12 and tap “RC” on the main interface
STEP 2): Tap Model Select and if required press “OK” to bypass any pop up
warning/alerts.
STEP 3): Tap to create a new model and if required press “OK” to bypass any
pop up warnings/alerts.
STEP 4): Tap Flight Settings and if required press “OK” to bypass any pop up
warnings/alerts.
STEP 5): Lift the H920 back end upward approximately 45°, then back down to
“level” twice till the main LED indicator blinks yellow.
STEP 6): Tap the Refresh icon. Select the code of the H920 listed in the
column under ”Model” and tap Bind ,then tap “OK” after the connection has
been established.
STEP 7): When tapping, you will hear two long beeps from the aircraft. That
means the ST12 is bound to the H920 successfully.
STEP 8): Tap twice to return to the main screen and the model /receiver should
automatically connect to ST12
NOTICE: The H920 main LED indicator will blink red and white if the
TORNADO loses GPS signal /lock. The H920 main LED indicator will be solid
color of the current mode if the GPS signal/lock is acquired.
Federal Communications Commission (FCC) Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
RF exposure warning
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used
for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must
not be collocated or operating in conjunction with any other antenna or transmitter.
IC Radiation Exposure Statement for Canada
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and
maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference
to other users, the antenna type and its gain should be so chosen that the equivalent is otropically radiated
power (e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par
Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres
utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
User manuals for transmitters equipped with detachable antennas shall also contain the following notice in a
conspicuous location:
This radio transmitter (identify the device by certification number, or model number if Category II) has been
approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain
and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having
a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle s'il
fait partie du matériel de catégorie I) a été approuvé par Industrie Canada pour fonctionner avec les types
d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type
d'antenne. Les types d'antenne non inclus dans cette liste,ou dont le gain est supérieur au gain maximal indiqué,
sont strictement interdits pour l'exploitation de l'émetteur.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with “Industry Canada RSS-102 for radiation exposure limits set forth for an
uncontrolled environment”.
This equipment should be installed and operated with minimum distance 20cm between the radiator and your
body.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

YUNEEC ST12 Manuel utilisateur

YUNEEC
Marque
YUNEEC
Modèle
ST12
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Autres documents