Craftsman CMCCS660E1 Mode d'emploi

Marque: Craftsman

Modèle: CMCCS660E1

Catégorie: Tronçonneuses électriques

Taper: Mode d'emploi

final page size: 8.5 x 5.5 in CRAFTSMANfinal page size: 8.5 x 5.5 in CRAFTSMAN

60V Max* 1

6" (40 cm) Chain Saw

Scie à chaîne 40 cm (16 po) 60 V max*

Sierra de Cadena de 40 cm (16") 60 V Máx*

CMCCS660

INSTRUCTION MANUAL | GUIDE D’UTILISATION | MANUAL DE INSTRUCTIONES

IF YOU HAVE QUESTIONS OR COMMENTS, CONTACT US.

POUR TOUTE QUESTION OU TOUT COMMENTAIRE, NOUS CONTACTER.

SI TIENE DUDAS O COMENTARIOS, CONTÁCTENOS.

1-888-331-4569 WWW.CRAFTSMAN.COM

English (original instructions) 1

Français (traduction de la notice d’instructions originale) 17

Español (traducido de las instrucciones originales) 35

ENGLISH

COMPONENTS

ON/OFF trigger switch

Lock-off lever

Chain brake / front hand

guard

Guide bar

Saw chain

Sprocket cover

Bubble level

Bar adjust locking knob

Chain tensioning knob

Oil level indicator

Guide bar cover

Rear handle

Front handle

Battery

Battery release button

Oil cap

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk

of personal injury or property damage.



DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or seriousinjury.



WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or seriousinjury.



CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderateinjury.



(Used without word) Indicates a safety related message.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in propertydamage.



WARNING: Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.



WARNING: Never modify the product or any part of it.

Damage or personal injury couldresult.

WARNING: To reduce the risk of injury, read the

instructionmanual.

If you have any questions or comments about this or

any product, call CRAFTSMAN toll free at:

1-888-331-4569.

Fig. A

English (original instructions)

ENGLISH

60V Max* 16" (40 cm) Chain Saw

CMCCS660

GENERAL POWER TOOL SAFETY WARNINGS



WARNING: Read all safety warnings,

instructions, illustrations and specifications

provided with this power tool. Failure to follow all

instructions listed below may result in electric shock,

fire and/or seriousinjury.

SAVE ALL WARNINGS AND

INSTRUCTIONS FOR FUTURE

REFERENCE

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

powertool.

1) Work Area Safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust orfumes.

c ) Keep children and bystanders away while

operating a power tool. Distractions can cause you

to losecontrol.

2) Electrical Safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will

reduce risk of electricshock.

b ) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet

conditions. Water entering a power tool will increase

the risk of electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electricshock.

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electricshock.

f ) If operating a power tool in a damp location

is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of a GFCI

reduces the risk of electricshock.

3) Personal Safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools

may result in serious personalinjury.

b ) Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personalinjuries.

c ) Prevent unintentional starting. Ensure the

switch is in the off position before connecting to

power source and/or battery pack, picking up or

carrying the tool. Carrying power tools with your

finger on the switch or energizing power tools that

have the switch on invitesaccidents.

d ) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personalinjury.

e ) Do not overreach. Keep proper footing and

balance at all times. This enables better control of

the power tool in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewelry. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewelry or

long hair can be caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used. Use of dust

collection can reduce dust-relatedhazards.

h ) Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles. A careless action can

cause severe injury within a fraction of a second.

4) Power Tool Use and Care

a ) Do not force the power tool. Use the correct

power tool for your application. The correct power

tool will do the job better and safer at the rate for

which it wasdesigned.

b ) Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must

berepaired.

c ) Disconnect the plug from the power source and/

or remove the battery, pack if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of

starting the power toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands

of untrainedusers.

e ) Maintain power tools and accesories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the power tool’s operation. If

ENGLISH

damaged, have the power tool repaired before

use. Many accidents are caused by poorly maintained

powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits, etc.

in accordance with these instructions, taking

into account the working conditions and the

work to be performed. Use of the power tool for

operations different from those intended could result

in a hazardoussituation.

h ) Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpected situations.

5) Battery Tool Use and Care

a ) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used

with another batterypack.

b ) Use power tools only with specifically designated

battery packs. Use of any other battery packs may

create a risk of injury andfire.

c ) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws, or other small metal objects,

that can make a connection from one terminal to

another. Shorting the battery terminals together may

cause burns or afire.

d ) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation

orburns.

e ) Do not use a battery pack or tool that is

damaged or modified. Damaged or modified

batteries may exhibit unpredictable behavior resulting

in fire, explosion or risk of injury.

f ) Do not expose a battery pack or tool to

fire or excessive temperature. Exposure to

fire or temperature above 265 °F (129 °C) may

causeexplosion.

g ) Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range specified in the instructions.

Charging improperly or at temperatures outside the

specified range may damage the battery and increase

the risk of fire.

6) Service

a ) Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

b ) Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized service providers.

Chain Saw Safety Warnings

a ) Keep all parts of the body away from the saw

chain when the chain saw, is operating. Before

you start the chain saw, make sure the saw

chain is not contacting anything. A moment of

inattention while operating chain saws may cause

entanglement of your clothing or body with the

sawchain.

b ) Always hold the chain saw with your right hand

on the rear handle and your left hand on the

front handle. Holding the chain saw with a reversed

hand configuration increases the risk of personal

injury and should never be done.

c ) Hold the power tool by insulated gripping

surfaces only, because the saw chain may

contact hidden wiring. Saw chains contacting

a "live" wire may make exposed metal parts of the

power tool "live" and could give the operator an

electric shock.

d ) Wear safety glasses and hearing protection.

Further protective equipment for head, hands,

legs and feet is recommended. Adequate protective

clothing will reduce personal injury by flying debris or

accidental contact with the saw chain.

e ) Do not operate a chain saw in a tree. Operation

of a chain saw while up in a tree may result in

personalinjury.

f ) Always keep proper footing and operate the

chain saw only when standing on fixed, secure

and level surface. Slippery or unstable surfaces such

as ladders may cause a loss of balance or control of

thechain saw.

g ) When cutting a limb that is under tension be

alert for spring back. When the tension in the wood

fibres is released the spring loaded limb may strike the

operator and/or throw the chain saw out of control.

h ) Use extreme caution when cutting brush and

saplings. The slender material may catch the

saw chain and be whipped toward you or pull you

offbalance.

i ) Carry the chain saw by the front handle with

the chain saw switched off and away from your

body. When transporting or storing the chain saw

always fit the guide bar cover. Proper handling of

the chain saw will reduce the likelihood of accidental

contact with the movingsaw chain.

j ) Follow instructions for lubricating, chain

tensioning and changing accessories. Improperly

tensioned or lubricated chain may either break or

increase the chance for kickback.

k ) Keep handles dry, clean, and free from oil and

grease. Greasy, oily handles are slippery causing loss

of control.

l ) Cut wood only. Do not use chain saw for

purposes not intended. For example: do not use

chain saw for cutting plastic, masonry or non-

ENGLISH

wood building materials. Use of the chain saw for

operations different than intended could result in a

hazardoussituation.

Causes and Operator Prevention

of Kickback

Kickback may occur when the nose or tip of the guide bar

touches an object, or when the wood closes in and pinches

the saw chain in the cut.

Tip contact in some cases may cause a sudden reverse

reaction, kicking the guide bar up and back towards

theoperator.

Pinching the saw chain along the top of the guide bar may

push the guide bar rapidly back towards theoperator.

Either of these reactions may cause you to lose control of

the saw which could result in serious personal injury. Do not

rely exclusively upon the safety devices built into your saw.

As a chain saw user, you should take several steps to keep

your cutting jobs free from accident or injury.

Kickback is the result of tool misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below:

a ) Maintain a firm grip, with thumbs and fingers

encircling the chain saw handles, with both

hands on the saw and position your body and

arm to allow you to resist kickback forces.

Kickback forces can be controlled by the

operator, if proper precautions are taken. Do not

let go of thechain saw.

b ) Do not overreach and do not cut above shoulder

height. This helps prevent unintended tip contact

and enables better control of the chain saw in

unexpectedsituations.

c ) Only use replacement bars and chains specified

by the manufacturer. Incorrect replacement

bars and chains may cause chain breakage and/

orkickback.

d ) Follow the manufacturer’s sharpening and

maintenance instructions for the saw chain.

Decreasing the depth gauge height can lead to

increased kickback.

6 . Use devices such as low kickback saw chain and reduced

kickback guide bars that reduce the risks associated

withkickback.

7 . Only use replacement bars and saw chains specified by

the manufacturer or the equivalent.

8 . Never let the moving saw chain contact any object at the

tip of the guide bar.

9 . Keep the working area free from obstructions such as

other trees, branches, rocks, fences, stumps, etc. Eliminate

or avoid any obstruction that your saw chain could hit

while you are cutting through a particular log or branch.

10 . Keep your saw chain sharp and properly tensioned. A

loose or dull chain can increase the chance of kickback.

Check tension at regular intervals with the motor stopped

and battery removed, never with the motor running.

11 . Begin and continue cutting only with the saw chain

moving at full speed. If the saw chain is moving at a

slower speed, there is a greater chance for kickback

tooccur.

12 . Cut one log at a time.

13 . Use extreme caution when re-entering a previous cut.

Engage ribbed bumpers into wood and allow chain to

reach full speed before proceeding with cut.

14 . Do not attempt plunge cuts or bore cuts.

15 . Watch for shifting logs or other forces that could close a

cut and pinch or fall into chain.

Kickback Safety Features



WARNING: The following features are included

on your saw to help reduce the hazard of kickback;

however such features will not totally eliminate this

dangerous reaction. As a chain saw user do not rely

only on safety devices. You must follow all safety

precautions, instructions, and maintenance in this

manual to help avoid kickback and other forces which

can result in serious injury.

• Reduced-Kickback Guide Bar, designed with a small

radius tip which reduces the size of the kickback

danger zone on bar tip. A reduced - kickback guide

bar is one which has been demonstrated to significantly

reduce the number and seriousness of kickbacks when

tested in accordance with safety requirements for electric

chain saws.

• Low-Kickback Chain, designed with a contoured

depth gauge and guard link which deflect kickback

force and allow wood to gradually ride into the

cutter. A low-kickback chain is a chain which has met

kickback performance requirements of ANSI B175.1–2012.

• Do not operate chain saw while in a tree, on a

ladder, on a scaffold, or from any unstable surface.

• Hold tool by insulated gripping surfaces when

performing an operation where the chain saw may

contact hidden wiring. Contact with a “live” wire will

make exposed metal parts of the tool “live” and shock

theoperator.

The Following Precautions Should Be

Followed to Minimize Kickback:

1 . Grip Saw Firmly. Hold the chain saw firmly with both

hands when the motor is running. Use a firm grip with

thumbs and fingers encircling the chain saw handles.

Chain saw will pull forward when cutting on the bottom

edge of the bar, and push backward when cutting along

the top edge of the bar.

2 . Do not over reach.

3 . Keep proper footing and balance at all times.

4 . Don’t let the nose of the guide bar contact a log, branch,

ground or other obstruction.

5 . Don’t cut above shoulder height.

ENGLISH

Chainsaw Names and Terms

• Bucking - The process of cross cutting a felled tree or log

intolengths.

• Motor Brake - A device used to stop the saw chain when

the trigger isreleased.

• Chain Saw Powerhead - A chain saw without the saw

chain and guidebar.

• Drive Sprocket or Sprocket - The toothed part that

drives the sawchain.

• Felling -

The process of cutting down atree.

• Felling Back Cut -

The final cut in a tree felling operation

made on the opposite side of the tree from the notchingcut.

• Front Handle - The support handle located at or toward

the front of the chainsaw.

• Front Hand Guard - A structural barrier between the

front handle of a chain saw and the guide bar, typically

located close to the hand position on the fronthandle.

• Guide Bar - A solid railed structure that supports and

guides the sawchain.

• Scabbard/Guide Bar Cover - Enclosure fitted over guide

bar to help prevent tooth contact when saw is not inuse.

• Kickback - The backward or upward motion, or both

of the guide bar occurring when the saw chain near the

nose of the top area of the guide bar contacts any object

such as a log or branch, or when the wood closes in and

pinches the saw chain in thecut.

• Do not attempt operations beyond your capacity or

experience. Read thoroughly and understand completely

all instructions in this manual.

• Before you start chain saw, make sure saw chain is

not contacting any object.

• Do not operate a chain saw with one hand! Serious

injury to the operator, helpers, or bystanders may

result from one handed operation. A chain saw is

intended for two-handed use only.

• Keep the handles dry, clean, and free of oil orgrease.

• Do not allow dirt, debris, or sawdust to build up on

the motor or outside air vents.

• Stop the chain saw before setting it down.

• Do not cut vines and/or small under brush.

• Use extreme caution when cutting small size brush

and saplings because slender material may catch

the saw chain and be whipped toward you or pull

you off balance.

• Keep the working area free from obstructions such

as other trees, branches, rocks, fences, stumps, etc.

Eliminate or avoid any obstruction that your saw chain could

hit while you are cutting through a particular log orbranch.

• Cut one log at atime.

• Use extreme caution when re-entering a previous

cut. Engage ribbed bumpers into wood and allow saw

chain to reach full speed before proceeding withcut.

• Do not attempt plunge cuts or borecuts.

• Watch for shifting logs or other forces that could

close a cut and pinch or fall intosaw chain.

• Kickback, Pinch -

The rapid pushback of the saw

which can occur when the wood closes in and pinches

the moving saw chain in the cut along the top of the

guidebar.

• Kickback, Rotational - The rapid upward and backward

motion of the saw which can occur when the moving saw

chain near the upper portion of the tip of the guide bar

contacts an object, such as a log orbranch.

• Limbing - Removing the branches from a fallen tree.

• Low-Kickback Chain - A chain that complies with the

kickback performance requirements of ANSI B175.1–2012

(when tested on a representative sample of chain saws.)

• Normal Cutting Position - Those positions assumed in

performing the bucking and fellingcuts.

• Notching Undercut - A notch cut in a tree that directs

the tree’sfall.

• Rear Handle - The support handle located at or toward

the rear of thesaw.

• Reduced Kickback Guide Bar - A guide bar which has

been demonstrated to reduce kickbacksignificantly.

• Replacement Saw Chain - A chain that complies with

kickback performance requirements of ANSI B175.1–2012

when tested with specific chain saws. It may not meet

the ANSI performance requirements when used with

othersaws.

• Saw Chain - A loop of chain having cutting teeth, that

cut the wood, and that is driven by the motor and is

supported by the guidebar.

• Ribbed Bumper - The ribs used when felling or bucking

to pivot the saw and maintain position whilesawing.

• Switch - A device that when operated will complete or

interrupt an electrical power circuit to the motor of the

chainsaw.

• Switch Linkage - The mechanism that transmits motion

from a trigger to theswitch.

• Switch Lockout - A movable stop that prevents

the unintentional operation of the switch until

manuallyactuated.

Additional Safety Information



WARNING: ALWAYS use safety glasses. Everyday

eyeglasses are NOT safety glasses. Also use face or

dust mask if cutting operation is dusty. ALWAYS WEAR

CERTIFIED SAFETYEQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratoryprotection.



WARNING: Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to the State

of California to cause cancer, birth defects or

other reproductive harm. Some examples of these

chemicalsare:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other

masonry products, and

ENGLISH

The label on your tool may include the following symbols. The

symbols and their definitions are asfollows:

V ......................... volts

Hz .......................hertz

min ..................... minutes

or DC ......direct current

...................... Class I Construction

(grounded)

…/min ..............per minute

BPM .................... beats per minute

IPM ..................... impacts per minute

RPM .................... revolutions per

minute

sfpm ................... surface feet per

minute

SPM .................... strokes per minute

OPM .................... oscillations per

minute

A ......................... amperes

W ........................watts

or AC ...........alternating current

or AC/DC .... alternating or

direct current

...................... Class II

Construction

(double insulated)

.......................no load speed

n .........................rated speed

......................earthing terminal

.....................safety alert symbol

.....................visible radiation

..................... avoid staring at

light

..................... wear respiratory

protection

..................... wear eye

protection

..................... wear hearing

protection

..................... read all

documentation

IPXX .................... IP symbol

• arsenic and chromium from chemically-

treatedlumber.

Your risk from these exposures varies, depending on

how often you do this type of work. To reduce your

exposure to these chemicals: work in a well ventilated

area, and work with approved safety equipment, such

as those dust masks that are specially designed to

filter out microscopicparticles.

• Avoid prolonged contact with dust from power

sanding, sawing, grinding, drilling, and other

construction activities. Wear protective clothing and

wash exposed areas with soap and water. Allowing

dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmfulchemicals.



WARNING: Use of this tool can generate and/

or disperse dust, which may cause serious and

permanent respiratory or other injury. Always use

NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles

away from face andbody.



WARNING: Always wear proper personal hearing

protection that conforms to ANSI S12.6 (S3.19)

during use. Under some conditions and duration

of use, noise from this product may contribute to

hearingloss.



CAUTION: When not in use, place tool on its

side on a stable surface where it will not cause

a tripping or falling hazard. Some tools will stand

upright but may be easily knocked over.

• Air vents often cover moving parts and should be

avoided. Loose clothes, jewelry or long hair can be

caught in movingparts.

READ ALL INSTRUCTIONS

Important Safety Instructions for All

Battery Packs



WARNING: Read all safety warnings,

instructions, and cautionary markings for the

battery pack, charger and product. Failure to

follow the warnings and instructions may result

in electric shock, fire and/or serious injury.

• Do not charge or use the battery pack in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Inserting or removing the battery

pack from the charger may ignite the dust orfumes.

• When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys,

nails, screws, or other small metal objects, that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause burns

or a fire.

• NEVER force the battery pack into the charger. DO

NOT modify the battery pack in any way to fit into

a non-compatible charger as battery pack may

rupture causing serious personal injury. Consult

the chart at the end of this manual for compatibility of

batteries andchargers.

• Charge the battery packs only in CRAFTSMAN chargers.

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in

locations where the temperature may reach or

exceed 104°F (40°C) (such as outside sheds or metal

buildings in summer). For best life store battery packs in

a cool, drylocation.

NOTE: Do not store the battery packs in a tool with

the trigger switch locked on. Never tape the trigger

switch in the ONposition.

• Do not incinerate the battery pack even if it is

severely damaged or is completely worn out. The

battery pack can explode in a fire. Toxic fumes and

BATTERIES AND CHARGERS

The battery pack is not fully charged out of the carton.

Before using the battery pack and charger, read the

safety instructions below and then follow charging

proceduresoutlined. When ordering replacement battery

packs, be sure to include the catalog number andvoltage.

CSPM .................. Cut strokes per

minute

..................... Do not leave in

rain

..................... Tip contact can

cause the guide

bar to move

suddenly upward

and backward,

which can cause

serious injury

.................... Contact of the

guide bar tip with

any object should

be avoided

.................. Rotational direction

of the saw chain

.............. Always use two

hands when

operating the

chain saw

ENGLISH

materials are created when lithium-ion battery packs

areburned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open

eye for 15 minutes or until irritation ceases. If medical

attention is needed, the battery electrolyte is composed of

a mixture of liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause

respiratory irritation. Provide fresh air. If symptoms

persist, seek medicalattention.



WARNING: Burn hazard. Battery liquid may be

flammable if exposed to spark orflame.



WARNING: Fire hazard. Never attempt to open the

battery pack for any reason. If the battery pack case

is cracked or damaged, do not insert into the charger.

Do not crush, drop or damage the battery pack. Do

not use a battery pack or charger that has received a

sharp blow, been dropped, run over or damaged in

any way (e.g., pierced with a nail, hit with a hammer,

stepped on). Damaged battery packs should be

returned to the service center forrecycling.

Storage Recommendations

1. The best storage place is one that is cool and dry, away

from direct sunlight and excess heat or cold.

2. For long storage, it is recommended to store a fully

charged battery pack in a cool dry place out of the

charger for optimal results.

NOTE: Battery packs should not be stored completely

depleted of charge. The battery pack will need to be

recharged before use.

Battery Pack Cleaning Instructions

Dirt and grease may be removed from the exterior of the

battery using a cloth or soft non-metallic brush. Do not use

water or any cleaningsolutions.

The RBRC® Seal

The RBRC® (Rechargeable Battery Recycling

Corporation) Seal on the nickel cadmium,

nickel metal hydride or lithium-ion batteries

(or battery packs) indicates that the costs

to recycle these batteries (or battery

packs) at the end of their useful life have already been

paid by CRAFTSMAN. In some areas, it is illegal to place

spent nickel cadmium, nickel metal hydride or lithium-ion

batteries in the trash or municipal solid waste stream and

the Call2Recycle® program provides an environmentally

consciousalternative.

Call 2 Recycle, Inc., in cooperation with CRAFTSMAN and

other battery users, has established the program in the

United States and Canada to facilitate the collection of

spent nickel cadmium, nickel metal hydride or lithium-ion

batteries. Help protect our environment and conserve

natural resources by returning the spent nickel cadmium,

nickel metal hydride or lithium-ion batteries to an

authorized service center or to your local retailer for

recycling. You may also contact your local recycling center

for information on where to drop off the spent battery.

RBRC® is a registered trademark of Call 2 Recycle,Inc.

Transportation



WARNING: Fire hazard. Do not store or carry the

battery pack so that metal objects can contact

exposed battery terminals. For example, do

not place the battery pack in aprons, pockets, tool

boxes, product kit boxes, drawers, etc., with loose

nails, screws, keys, etc. Transporting batteries

can possibly cause fires if the battery terminals

inadvertently come in contact with conductive

materials such as keys, coins, hand tools and the

like. The US Department of Transportation Hazardous

Material Regulations (HMR) actually prohibit

transporting batteries in commerce or on airplanes

in carry-on baggage UNLESS they are properly

protected from short circuits. So when transporting

individual battery packs, make sure that the battery

terminals are protected and well insulated from

materials that could contact them and cause a short

circuit. NOTE:LI-ion batteries should not be put in

checkedbaggage.

Important Safety Instructions for All

Battery Chargers



WARNING: Read all safety warnings, instructions,

and cautionary markings for the battery pack,

charger and product. Failure to follow the

warnings and instructions may result in electric

shock, fire and/or seriousinjury.

• DO NOT attempt to charge the battery pack with

any chargers other than a CRAFTSMAN charger.

CRAFTSMAN charger and battery pack are specifically

designed to worktogether.

• These chargers are not intended for any uses other

than charging CRAFTSMAN rechargeable batteries.

Any other uses may result in risk of fire, electric shock

orelectrocution.

• Do not expose the charger to rain orsnow.

• Pull by the plug rather than the cord when

disconnecting the charger. This will reduce the risk of

damage to the electric plug andcord.

• Make sure that the cord is located so that it will not

be stepped on, tripped over or otherwise subjected

to damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in

risk of fire, electric shock orelectrocution.

• When operating a charger outdoors, always provide

a dry location and use an extension cord suitable

for outdoor use. Use of a cord suitable for outdoor use

reduces the risk of electricshock.

• An extension cord must have adequate wire size

(AWG or American Wire Gauge) for safety. The

smaller the gauge number of the wire, the greater the

capacity of the cable, that is, 16 gauge has more capacity

than 18gauge. An undersized cord will cause a drop in

ENGLISH

line voltage resulting in loss of power and overheating.

When using more than one extension to make up the

total length, be sure each individual extension contains at

least the minimum wire size. The following table shows

the correct size to use depending on cord length and

nameplate ampere rating. If in doubt, use the next heavier

gauge. The lower the gauge number, the heavier thecord.

Minimum Gauge for Cord Sets

Volts

Total Length of Cord in Feet

(meters)

120 V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Ampere Rating

American Wire Gauge

Than

Not

Than

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of the charger or

place the charger on a soft surface that might block

the ventilation slots and result in excessive internal

heat. Place the charger in a position away from any heat

source. The charger is ventilated through slots in the top

and the bottom of thehousing.

• Do not operate the charger with a damaged cord

orplug–have them replaced immediately.

• Do not operate the charger if it has received a sharp

blow, been dropped or otherwise damaged in any

way. Take it to an authorized servicecenter.

• Do not disassemble the charger; take it to an

authorized service center when service or repair is

required. Incorrect reassembly may result in a risk of

electric shock, electrocution orfire.

• Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk

of electric shock. Removing the battery pack will not

reduce thisrisk.

• NEVER attempt to connect 2 chargerstogether.

• The charger is designed to operate on standard

120V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.



WARNING: Shock hazard. Do not allow any liquid to

get inside the charger. Electric shock mayresult.



WARNING: Burn hazard. Do not submerge the

battery pack in any liquid or allow any liquid to

enter the battery pack. Never attempt to open the

battery pack for any reason. If the plastic housing of

the battery pack breaks or cracks, return to a service

center for recycling.



CAUTION: Burn hazard. To reduce the risk of injury,

charge only CRAFTSMAN rechargeable battery packs.

Other types of batteries may overheat and burst

resulting in personal injury and propertydamage.



CAUTION: Under certain conditions, with the charger

plugged into the power supply, the charger can

be shorted by foreign material. Foreign materials

of a conductive nature, such as, but not limited to,

grinding dust, metal chips, steel wool, aluminum

foil or any buildup of metallic particles should be

kept away from the charger cavities. Always unplug

the charger from the power supply when there is no

battery pack in the cavity. Unplug the charger before

attempting toclean.

Charging a Battery

NOTE: To ensure maximum performance and life of

lithium-ion battery packs, charge the battery pack fully

before firstuse.

1. Plug the charger into an appropriate outlet before

inserting batterypack.

2. Connect the charger and battery pack, making sure

the battery is fully seated. The (charging) light will

blink continuously indicating that the charging process

hasstarted.

3. The completion of charge will be indicated by the light

remaining ON continuously. The battery pack is fully

charged and may be removed and used at this time or

left in the charger.

NOTE: To remove the battery pack, some chargers require

the battery pack release button to bepressed.

Indicators

Charging

Fully Charged

Hot/Cold Pack Delay

A charger will not charge a faulty battery pack. The charger

refusing to light could indicate a problem with the charger.

NOTE: If the charger refuses to light, take the charger and

battery pack to be tested at an authorized servicecenter.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot

or too cold, it automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery pack has reached an

appropriate temperature. The charger then automatically

switches to the pack charging mode. This feature ensures

maximum battery packlife.

A cold battery pack may charge at a slower rate than a

warm batterypack.

Important Charging Notes

1. Longest life and best performance can be obtained if

the battery pack is charged when the air temperature

is between 65°F – 75°F (18° C– 24°C). DO NOT charge

when the battery pack is below +40°F (+4.5°C), or

above +104°F (+40°C). This is important and will

prevent serious damage to the batterypack.

2. The charger and battery pack may become warm to the

touch while charging. This is a normal condition, and

does not indicate a problem. To facilitate the cooling of

ENGLISH

the battery pack after use, avoid placing the charger or

battery pack in a warm environment such as in a metal

shed or an uninsulatedtrailer.

3. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp

or other appliance;

b. Check to see if receptacle is connected to a light

switch which turns power off when you turn out

the lights;

c. Move the charger and battery pack to a location

where the surrounding air temperature is

approximately 65°F – 75°F (18°C – 24°C);

d. If charging problems persist, take the tool, battery

pack and charger to your local servicecenter.

4. The battery pack should be recharged when it fails to

produce sufficient power on jobs which were easily

done previously. DO NOT CONTINUE to use under these

conditions. Follow the charging procedure. You may

also charge a partially used pack whenever you desire

with no adverse effect on the batterypack.

5. Foreign materials of a conductive nature such as, but

not limited to, grinding dust, metal chips, steel wool,

aluminum foil, or any buildup of metallic particles

should be kept away from charger cavities. Always

unplug the charger from the power supply when there

is no battery pack in the cavity. Unplug the charger

before attempting toclean.

6. Do not freeze or immerse the charger in water or any

otherliquid.

Charger Cleaning Instructions



WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger

using a cloth or soft non-metallic brush. Do not use

water or any cleaningsolutions.

SAVE THESE INSTRUCTIONS FOR

FUTURE USE

COMPONENTS (FIG. A)

Intended Use

This chain saw is designed for pruning applications

and cutting logs up to 14" (355 mm) indiameter.

DO NOT use under wet conditions or in presence of

flammable liquids orgases.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

ASSEMBLY AND ADJUSTMENTS



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.

Installing the Guide Bar and Saw Chain

(Fig. A, B–D)



CAUTION: Sharp chain. Always wear protective

gloves when handling the chain. The chain is sharp

and can cut you when it is notrunning.



WARNING: Sharp moving chain. To prevent

accidental operation, ensure that battery is removed

from the tool before performing the following

operations. Failure to do this could result in serious

personalinjury.

If the saw chain

5

and guide bar

4

are packed separately

in the carton, the chain has to be attached to the bar, and

both must be attached to the body of thetool.

1. Place the saw on a flat, firmsurface.

2. Flip up locking lever and rotate the bar adjust locking

knob

8

counterclockwise as shown in FigureB to

remove sprocket cover

6

3. Wearing protective gloves, grasp the saw chain

5

and

wrap it around the guide bar

4

, ensuring the teeth are

facing the correct direction.

4. Ensure the chain is properly set in the slot around the

entire guidebar.

5. Place the saw chain around the sprocket

17

. While

lining up the slot on the guide bar with chain tensioning

18

, and the bolt

19

, on the base of the tool.

6. Once in place, hold the bar still, replace sprocket

cover

6

. Make sure tool-free tension assembly bolt

hole on the cover lines up with the bolt

19

, in the

main housing. Flip up locking lever and rotate the bar

adjust locking knob

8

clockwise until it clicks, then

loosen knob one full turn, so that the saw chain can be

properlytensioned.

7. Rotate the chain tensioning knob

9

clockwise to

increase tension as shown in FigureD. Make sure the

saw chain

5

is snug around the guide bar

4

. Tighten

the bar adjust locking knob until it clicks. The bar is

secure after three audible clicks are heard. Further

tightening is notrequired.

Fig. B

Components

Tool Use

chain saw xxxxxxxxxxx

ENGLISH

Fig. C

Fig. D

Adjusting Chain Tension (Fig. A, E )



CAUTION: Sharp chain. Always wear protective

gloves when handling the chain. The chain is sharp

and can cut you when it is notrunning.



WARNING: Sharp moving chain. To prevent

accidental operation, ensure that battery is removed

from the tool before performing the following

operations. Failure to do this could result in serious

personalinjury.

1. With the saw on a flat, firm surface, check the saw chain

5

tension. The tension is correct when the chain snaps

back after being pulled 1/8" (3mm) away from the

guide bar

4

with light force from the index finger and

thumb as shown in FigureE. There should be no “sag”

between the guide bar and the chain on the underside

as shown in FigureE.

2. To adjust saw chain tension, flip up locking tab and

rotate the bar adjust locking knob

8

counterclockwise

one full turn. Rotate the chain tensioning knob

9

clockwise until the chain tension is correct as

instructedabove.

3. Do not over-tension the chain as this will lead to

excessive wear and will reduce the life of the bar

andchain.

4. Once chain tension is correct, securely tighten bar adjust

lockingknob.

NOTE: The bar adjust locking knob has a detent tightening

system. The sprocket cover is secure after three audible

clicks are heard. Further tigtening is notrequired.

5. When the chain is new, check the tension frequently

(after removing battery) during the first 2 hours of use as

a new chain stretchesslightly.

Fig. E

1/8” (3mm)

Replacing the Saw Chain (Fig. A, F)



CAUTION: Sharp chain. Always wear protective

gloves when handling the chain. The chain is sharp

and can cut you when it is notrunning.



WARNING: Sharp moving chain. To prevent

accidental operation, ensure that battery is removed

from the tool before performing the following

operations. Failure to do this could result in serious

personalinjury.

1. Flip up locking tab and rotate the bar adjust locking

knob

8

counterclockwise to release chaintension.

2. Remove sprocket cover

6

as described in Installing the

Guide Bar and Saw Chainsection.

3. Lift the worn saw chain

5

out of the groove in the

guide bar

4

4. Place the new chain in the slot of the guide bar, making

sure the saw teeth are facing the correct direction by

matching the arrow on the chain with the graphic on

the sprocket cover

6

shown in FigureF.

5. Follow instructions for Installing the Guide Bar and

SawChain.

Fig. F

Replacement chain and bar are available from your

nearest authorized servicecenter.

• This chain saw requires replacement 16” (406 mm) chain

CMZCSC16. Replacement 16” bar CMZCSB16.

Saw Chain and Guide Bar Oiling (Fig. G)

Auto Oiling System

This chain saw is equipped with an auto oiling system that

keeps the saw chain and guide bar constantly lubricated.

The oil level indicator

10

shows the level of the oil in the

chain saw. If the oil level is less than a quarter full, remove

the battery from the chain saw and refill with the correct

type of oil. Always empty oil tank when finishedcutting.

ENGLISH

NOTE: Use a high quality bar and chain oil for proper saw

chain and bar lubrication. As a temporary substitute, a non-

detergent SAE30 weight motor oil can be used. The use of

a vegetable based bar and chain oil is recommended when

pruning trees. Mineral oil is not recommended because it

may harm trees. Never use waste oil or very thick oil. These

may damage yourchain saw.

Filling the Oil Reservoir

1. Unscrew counterclockwise and then remove the oil cap

16

. Fill the reservoir with the recommended bar and

chain oil until the oil level has reached the top of the oil

level indicator

10

2. Refit the oil cap and tighten clockwise.

3. Periodically switch the chain saw off and check the oil

level indicator to ensure the bar and chain are being

properlyoiled.

Fig. G

Transporting Chain Saw (Fig. A, H)

• Always remove the battery from the tool and cover the

guide bar

4

with the guide bar cover

11

(see FigureH)

when transporting thesaw.

• Engage chain brake by pushing chain brake / front hand

guard

3

forward.

Fig. H

To remove the battery pack from the tool, press the release

button

15

and firmly pull the battery pack out of the tool

handle. Insert it into the charger as described in the charger

section of thismanual.

Fig. I

Proper Hand Position (Fig. A, J)



WARNING: To reduce the risk of serious personal injury,

Always use proper hand position as shown.



WARNING:

To reduce the risk of serious personal injury,

always hold securely in anticipation of a suddenreaction.

Proper hand position requires the left hand on the front

handle

13

, with the right hand on the rear handle

12

Fig. J

Operating the Chain Saw (Fig. A)



WARNING: Read and understand all instructions.

Failure to follow all instructions listed below

may result in electric shock, fire and/or serious

personalinjury.

• Guard Against Kickback which can result in

severe injury or death. See General Power Tool

Safety Warnings and Causes and Operator

Prevention of Kickback and Kickback Safety

Features, to avoid the risk ofkickback.

• Do not overreach. Do not cut above chest height.

Make sure your footing is firm. Keep feet apart.

Divide your weight evenly on bothfeet.

• Use a firm grip with your left hand on the front

handle

13

and your right hand on the rear

OPERATION



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.

Installing and Removing the Battery Pack

(Fig. I)

NOTE: For best results, make sure your battery pack is

fullycharged.

To install the battery pack

14

into the tool handle, align the

battery pack with the rails inside the tool’s handle and slide

it into the handle until the battery pack is firmly seated in

the tool and ensure that it does notdisengage.

ENGLISH

handle

12

so that your body is to the left of the

guidebar.

• Do not hold chain saw by chain brake / front

hand guard

3

. Keep elbow of left arm locked so

that left arm is straight to withstand akickback.



WARNING: Never use a cross-handed grip (left

hand on the rear handle and right hand on the

fronthandle).



WARNING: Never allow any part of your body to

be in line with the guide bar

4

when operating the

chainsaw.

• Never operate while in a tree, in any awkward

position or on a ladder or other unstable surface.

You may lose control of saw causing severeinjury.

• Keep the chain saw running at full speed the entire

time you arecutting.

• Allow the saw chain to cut for you. Exert only light

pressure. Do not put pressure on chain saw at

end ofcut.



WARNING: When not in use always have the

chain brake engaged and batteryremoved.

Setting the Chain Brake (Fig. K)

Your chain saw is equipped with a motor chain braking

system which will stop the chain quickly in case ofkickback.

1. Remove the battery from thetool.

2. To engage the chain brake, push the chain brake / front

hand guard

3

forward until it clicks intoplace.

3. Pull the chain brake / front hand guard

3

towards the

front handle

13

into the “set” position as shown in

FigureK.

4. The tool is now ready touse.

NOTE: In the event of kickback, your left hand will come in

contact with the front guard, pushing it forward, toward the

workpiece. This will stop thetool.

Fig.K

Testing the Chain Brake

Test the chain brake before every use to make sure it

operatescorrectly.

1. Place the tool on a flat, firm surface. Make sure the saw

chain

5

is clear of theground.

2. Grip the tool firmly with both hands and turn the chain

sawon.

3. Rotate your left hand forward around the front handle

13

so the back of your hand comes in contact with

the chain brake / front hand guard

3

and push it

forward, toward the workpiece. The saw chain should

stopimmediately.

NOTE: If saw does not stop immediately, stop use of tool

and bring it to an authorized service center nearestyou.



WARNING: Make sure to set chain brake

beforecutting.

ON/OFF Switch (Fig. L)

Always be sure of your footing and grip the chain saw firmly

with both hands with the thumb and fingers encircling

bothhandles.

To turn the unit on, ensure chain brake is not engaged.

Push the lock off lever

2

and squeeze the On/Off trigger

switch

1

. Once the unit is running, you may release the lock

offlever.

In order to keep the unit running you must continue to

squeeze the trigger. To turn the unit off, release thetrigger.

NOTE: If too much force is applied while making a cut the

saw will turn off. To restart saw, you must release the

On/Off trigger switch

1

before the saw will restart. Begin

your cut again this time with less force. Allow the saw to cut

at its ownpace.



WARNING: Never attempt to lock a switch in the

ONposition.

Fig. L

Bubble Level (Fig. A, Q)



WARNING: Do not operate above shoulder height

Align bubble levels prior to making a cut.

Ideal for vertical cutting to ensure a straight, flat cut.

1. Align the bubble level

2. Always start a cut with the saw chain running at

fullspeed.

3. Place the bottom spike

20

of the chain saw behind the

area of the initial cut.

4. Once a cut has begun and a notch is established in the

material, do not change the angle of the cut.

NOTE: Changing the angle will cause the bar to bend.

ENGLISH

Common Cutting Techniques (Fig. A, M–S)

Felling

The process of cutting down a tree. Be sure battery is fully

charged before felling a tree so you can finish on a single

charge. Do not fell trees in high windconditions.



WARNING: Felling can result in injury. It should only

be performed by a trainedperson.

• A retreat path should be planned and cleared as

necessary before cuts are started. The retreat path

should extend back and diagonally to the rear of the

expected line of fall (FigureM).

DIRECTION

FALL

RETREAT

45°

TREE

Fig. M

45°

RETREAT

• Before felling is started, consider the natural lean of

the tree, the location of larger branches and the wind

direction to judge which way the tree will fall. Have

wedges (wood, plastic or aluminum) and a heavy mallet

handy. Remove dirt, stones, loose bark, nails, staples,

and wire from the tree where the felling cuts are to

bemade.

• Notching Undercut - Make the notch 1/3 of the

diameter of the tree, perpendicular to the direction of

the fall. Make the lower horizontal notching cut first.

This will help to avoid pinching of either the saw chain

or the guide bar when the second notch cut is being

made (FigureN).

• Felling Back Cut - Make the felling back cut at least 2"

(51mm) higher than the horizontal notching cut. Keep

the felling back cut parallel to the horizontal notching

cut. Make the felling back cut so enough wood is left

to act as a hinge. The hinge wood keeps the tree from

twisting and falling in the wrong direction. Do not cut

through the hinge (FigureN).

• As the felling cut gets close to the hinge the tree should

begin to fall. If there is any chance that the tree may

not fall in the desired direction or it may rock back and

bind the saw chain, stop cutting before the felling cut

is complete and use wedges to open the cut and drop

the tree along the desired line of fall. When the tree

begins to fall remove the chain saw from the cut, stop

the motor, put the chain saw down, then use the retreat

path planned. Be alert for overhead limbs falling and

watch yourfooting.

2" (51 mm)

DIRECTION OF FALL

2" (51 mm)

HINGE

NOTCH

FELLING BACK CUT

Fig. N

Limbing

Removing the branches from a fallen tree. When limbing,

leave larger lower limbs to support the log off the ground.

Remove the small limbs in one cut. Branches under tension

should be cut from the bottom of the branch towards the

top to avoid binding the chain saw as shown in FigureO.

Trim limbs from opposite side keeping tree stem between

you and saw. Never make cuts with saw between your legs

or straddle the limb to becut.

Fig. O

Bucking



WARNING: Recommend that first time users should

practice cutting on a sawhorse.

Cutting a felled tree or log into lengths. How you should

cut depends on how the log is supported. Use a saw horse

(FigureP) wheneverpossible.

Fig. P

1. Always start a cut with the saw chain running at

fullspeed.

2. Place the bottom spike

20

of the chain saw behind the

area of the initial cut as shown in FigureQ.

3. Turn the chain saw on then rotate the saw chain and bar

down into the tree, using the spike as ahinge.

ENGLISH

4. Once the chain saw gets to a 45 degree angle, level

the chain saw again and repeat steps until you cut

fullythrough.

5. When the tree is supported along its entire length, make

a cut from the top (overbuck), but avoid cutting the

earth as this will dull your sawquickly.

CUT FROM TOP (OVERBUCK)

AVOID CUTTING EARTH

Fig. Q

• FigureR- When supported at one end

First, cut 1/3 the diameter from the underside

(underbuck). Then make the finishing cut by

overbucking to meet the firstcut.

2nd CUT OVERBUCK

(2/3 DIAMETER)

TO MEET 1st CUT

(TO AVOID PINCHING)

1st CUT UNDERBUCK

(1/3 DIAMETER)

AVOID SPLINTERING

Fig. R

• FigureS- When supported at bothends. First, cut 1/3

down from the top overbuck. Then make the finished

cut by underbucking the lower 2/3 to meet the firstcut.

2nd CUT UNDERBUCK

(2/3 DIAMETER)

TO MEET 1st CUT

(TO AVOID PINCHING)

1st CUT OVERBUCK

(1/3 DIAMETER)

TO AVOID SPLINTERING

Fig. S

• When on a slope always stand on the uphill side of the

log. When “cutting through”, to maintain complete

control reduce the cutting pressure near the end of the

cut without relaxing your grip on the chain saw handles.

Don’t let the chain contact the ground. After completing

the cut, wait for the saw chain to stop before you move

the chain saw. Always stop the motor before moving

from cut tocut.

MAINTENANCE



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.

Regular maintenance ensures a long effective life for your

chainsaw.

Saw Chain and Guide Bar

After every few hours of use, remove the sprocket cover,

guide bar and chain and clean thoroughly using a soft

bristle brush. Ensure oiling hole on bar is clear of debris.

When replacing dull chains with sharp chains it is good

practice to flip the chain bar from bottom totop.

Saw Chain Sharpening



CAUTION: Sharp chain. Always wear protective

gloves when handling the chain. The chain is sharp

and can cut you when it is notrunning.



WARNING: Sharp moving chain. To prevent

accidental operation, ensure that battery is removed

from the tool before performing the following

operations. Failure to do this could result in serious

personalinjury.

NOTE: The cutters will dull immediately if they touch the

ground or a nail whilecutting.

To get the best possible performance from your chain saw

it is important to keep the teeth of the saw chain sharp.

Follow these helpful tips for proper saw chain sharpening:

1. For best results use a 4.5mm file and a file holder or

filing guide to sharpen your saw chain. This will ensure

you always get the correct sharpeningangles.

2. Place the file holder flat on the top plate and depth

gauge of thecutter.

3. FigureT- Keep the correct top plate

21

filing angle line

of 30° on your file guide parallel with your chain (file at

60° from chain viewed from the side).

4. Sharpen cutters on one side of the chain first. File from

the inside of each cutter to the outside. Then turn your

saw around and repeat the processes (2, 3, 4) for cutters

on the other side of thechain.

NOTE: Use a flat file to file the tops of the rakers (portion

of chain link in front of the cutter) so they are about

.025" (.635 mm) below the tips of the cutters as shown

in FigureU.

5. FigureV- Keep all cutter lengthsequal.

6. If damage is present on the chrome surface of the

top plates or side plates, file back until such damage

isremoved.



CAUTION: After filing, the cutter will be sharp, use

extra caution during thisprocess.

NOTE: Each time the chain is sharpened, it loses some of

the low kickback qualities and extra caution should be used.

It is recommended that a saw chain be sharpened no more

than fourtimes.

ENGLISH

60°

Fig. T

.025"

(0.635mm)

Fig. U

Fig. V

Accessories



WARNING: Since accessories, other than those

offered by CRAFTSMAN, have not been tested with

this product, use of such accessories with this tool

could be hazardous. To reduce the risk of injury, only

CRAFTSMAN recommended accessories should be

used with thisproduct.

Recommended accessories for use with your tool are

available at extra cost from your local dealer or authorized

service center. If you need assistance in locating any

accessory, please contact CRAFTSMAN, call 1-888-331-4569.



WARNING: When hanging objects on a Versatrack™

Trackwall rail, adequately space the tools in order to

not exceed 75 lb (35 kg) per linear foot.



WARNING: Before using the tool make sure that the

Versatrack™ integral hang hook is returned to its

original position.

IMPORTANT: Versatrack™ accessories mount compatible

tools securely to the Versatrack™ Trackwallsystem.

1. Turn tool off, remove the battery pack and

removeaccessories.



CAUTION: Any product with exposed cutting teeth

must have them covered securely if it is to be on

theVersatrack™ Trackwall.

2. Flip or pull open the integral hang hook

. It clicks

when locked into position.

3. Mount the integral hang hook to the

Versatrack™Trackwall.

NOTE: Versatrack™ accessories for use with your tool are

available at extra cost from your local dealer or authorized

service center. If you need assistance in locating any

accessory, please contact CRAFTSMAN, call 1-888-331-4569.

Fig.W

Versatrack™ (Fig. W)



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.



WARNING: To reduce the risk of serious personal

injury, do not use a damaged Versatrack™ integral

hang hook or Versatrack™ Trackwall. A damaged

Versatrack™ integral hang hook or Versatrack™

Trackwall will not support the weight of the tool.



WARNING: To reduce the risk of serious personal

injury, DO NOT suspend tool overhead or suspend

objects from the integral hang hook. ONLY suspend

tool on the Versatrack™ Trackwall using the integral

hang hook.



WARNING: The Versatrack™ integral hang hook

is intended to mount the tool onto a Versatrack™

Trackwall rail. Do not use the integral hang hook to

mount the tool to any other surface.



WARNING: The Versatrack™ integral hang hook is

not a belt hook.

Repairs

The charger and battery pack are notserviceable. There are

no serviceable parts inside the charger or battery pack.



WARNING: To assure product SAFETY and

RELIABILITY, repairs, maintenance and adjustment

(including brush inspection and replacement, when

applicable) should be performed by a CRAFTSMAN

factory service center or a CRAFTSMAN authorized

service center. Always use identical replacementparts.

Cleaning



WARNING: Blow dirt and dust out of all air vents with

clean, dry air at least once a week. To minimize the risk

of eye injury, always wear ANSI Z87.1 approved eye

protection when performingthisprocedure.

ENGLISH



WARNING: Never use solvents or other harsh

chemicals for cleaning the non-metallic parts of

the tool. These chemicals may weaken the plastic

materials used in these parts. Use a cloth dampened

only with water and mild soap. Never let any liquid

get inside the tool; never immerse any part of the tool

into aliquid.

Thank you for your purchase. Register your product nowfor:

• WARRANTY SERVICE: Registering your product will

help you obtain more efficient warranty service in case

there is a problem with yourproduct.

• CONFIRMATION OF OWNERSHIP: In case of an

insurance loss, such as fire, flood or theft, your

registration of ownership will serve as your proof

ofpurchase.

• FOR YOUR SAFETY: Registering your product will

allow us to contact you in the unlikely event a safety

notification is required under the Federal Consumer

SafetyAct.

FREE WARNING LABEL REPLACEMENT: If your warning

labels become illegible or are missing, call 1-888-331-4569

for a freereplacement.

Four Year Limited Warranty

CRAFTSMAN will repair or replace, without charge, any

defects due to faulty materials or workmanship for four

years from the date of purchase. This warranty does

not cover part failure due to normal wear or tool abuse.

For further detail of warranty coverage and warranty

repair information, visit www.craftsman.com or call

1-888-331-4569. This warranty does not apply to

accessories or damage caused where repairs have been

made or attempted by others. THIS LIMITED WARRANTY

IS GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED

WARRANTY OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL

OR CONSEQUENTIAL DAMAGES. Some states do not allow

limitations on how long an implied warranty lasts or the

exclusion or limitation of incidental or consequential

damages, so these limitations may not apply to you. This

warranty gives you specific legal rights and you may have

other rights which vary in certain states orprovinces.

NOTE: Battery warranty voided if the battery pack is

tampered with in any way. CRAFTSMAN is not responsible

for any injury caused by tampering and may prosecute

warranty fraud to the fullest extent permitted bylaw.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of

your CRAFTSMAN Power Tool or Nailer for any reason, you

can return it within 90 days from the date of purchase with

a receipt for a full refund – no questionsasked.

LATIN AMERICA: This warranty does not apply to products

sold in Latin America. For products sold in Latin America,

see country specific warranty information contained in

the packaging, call the local company or see website for

warrantyinformation.

FRANÇAIS

Français (traduction de la notice d’instructions originale)

LangRef_U_NA_U_U-FRE

DESCRIPTION

Détente à vitesse

variable

Levier de blocage

Frein de chaîne/pare-

main avant

Guide-chaîne

Chaîne de scie

Couvercle du pignon

Niveau à bulle

Bouton de réglage du

guide-chaîne

Bouton tendeur de

chaîne

Indicateur de niveau

d’huile

Capot du guide-chaîne

Poignée arrière

Poignée avant

Bloc-piles

Bouton de dégagement

du bloc-piles

Bouchon du réservoir

d’huile

Définitions : symboles et termes d'alarmes sécurité

Ces guides d'utilisation utilisent les symboles et termes d'alarmes sécurité suivants pour vous prévenir de situations

dangereuses et de risques de dommages corporels ou matériels.



DANGER : indique une situation dangereuse imminente qui, si elle n’est pas évitée, entraînera la mort ou des

blessuresgraves.



AVERTISSEMENT : indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait entraîner la

mort ou des blessuresgraves.



ATTENTION : indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait entraîner des

blessures légères oumodérées.



(Si utilisé sans aucun terme) Indique un message propre à la sécurité.

AVIS : indique une pratique ne posant aucun risque de dommages corporels mais qui par contre, si rien n’est fait

pour l’éviter, pourrait poser des risques de dommages matériels.



AVERTISSEMENT : lire tous les avertissements

de sécurité et toutes les directives. Le non-respect

des avertissements et des directives pourrait se

solder par un choc électrique, un incendie et/ou une

blessuregrave.



AVERTISSEMENT : ne jamais modifier l’outil

électrique ni aucun de ses composants, car il y a

risques de dommages corporels oumatériels.

AVERTISSEMENT : afin de réduire le risque de

blessures, lire le mode d’emploi del’outil.

Pour toute question ou remarque au sujet de cet outil

ou de tout autre outil CRAFTSMAN composez le

numéro sans frais : 1-888-331-4569.

Fig. A

FRANÇAIS

Scie à chaîne 40 cm (16 po) 60 V max*

CMCCS660

AVERTISSEMENTS GÉNÉRAUX SUR LA

SÉCURITÉ DES OUTILS



AVERTISSEMENT : lisez tous les avertissements

de sécurité, toutes les instructions, les

illustrations et les caractéristiques fournis

avec cet outil électrique. Ne pas suivre toutes

les instructions comprises aux présentes peut

conduire à un choc électrique, un incendie et/ou des

blessuresgraves.

CONSERVER TOUS LES

AVERTISSEMENTS ET TOUTES

LES DIRECTIVES POUR UN

USAGE ULTÉRIEUR

Le terme « outil électrique » cité dans les avertissements se

rapporte à votre outil électrique à alimentation sur secteur

(avec fil) ou par piles (sans fil).

1) Sécurité du lieu de travail

a ) Tenir l’aire de travail propre et bien éclairée.

Les lieux encombrés ou sombres sont propices

auxaccidents.

b ) Ne pas faire fonctionner d’outils électriques

dans un milieu déflagrant, tel qu’en présence de

liquides, de gaz ou de poussières inflammables.

Les outils électriques produisent des étincelles qui

pourraient enflammer la poussière ou lesvapeurs.

c ) Éloigner les enfants et les personnes à proximité

pendant l’utilisation d’un outil électrique. Une

distraction pourrait en faire perdre la maîtrise

àl’utilisateur.

2) Sécurité en matière d’électricité

a ) Les fiches des outils électriques doivent

correspondre à la prise. Ne jamais modifier la

fiche d’aucune façon. Ne jamais utiliser de fiche

d’adaptation avec un outil électrique mis à la

terre. Le risque de choc électrique sera réduit par

l’utilisation de fiches non modifiées correspondant à

laprise.

b ) Éviter tout contact physique avec des surfaces

mises à la terre comme des tuyaux, des

radiateurs, des cuisinières et des réfrigérateurs.

Le risque de choc électrique est plus élevé si votre

corps est mis à laterre.

c ) Ne pas exposer les outils électriques à la pluie ou

à l’humidité. La pénétration de l’eau dans un outil

électrique augmente le risque de chocélectrique.

d ) Ne pas utiliser le cordon de façon abusive. Ne

jamais utiliser le cordon pour transporter, tirer

ou débrancher un outil électrique. Tenir le

cordon éloigné de la chaleur, de l’huile, des

bords tranchants et des pièces mobiles. Les

cordons endommagés ou enchevêtrés augmentent les

risques de chocélectrique.

e ) Pour l’utilisation d’un outil électrique à

l’extérieur, se servir d’une rallonge convenant à

cette application. L’utilisation d’une rallonge conçue

pour l’extérieur réduira les risques de chocélectrique.

f ) S’il est impossible d’éviter l’utilisation d’un

outil électrique dans un endroit humide,

brancher l’outil dans une prise ou sur un circuit

d’alimentation dotés d’un disjoncteur de fuite à

la terre (GFCI). L’utilisation de ce type de disjoncteur

réduit les risques de chocélectrique.

3) Sécurité personnelle

a ) Être vigilant, surveiller le travail effectué et faire

preuve de jugement lorsqu’un outil électrique

est utilisé. Ne pas utiliser d’outil électrique en

cas de fatigue ou sous l’influence de drogues,

d’alcool ou de médicaments. Un simple moment

d’inattention en utilisant un outil électrique peut

entraîner des blessures corporellesgraves.

b ) Utiliser des équipements de protection

individuelle. Toujours porter une protection

oculaire. L’utilisation d’équipements de protection

comme un masque antipoussière, des chaussures

antidérapantes, un casque de sécurité ou des

protecteurs auditifs lorsque la situation le requiert

réduira les risques de blessurescorporelles.

c ) Empêcher les démarrages intempestifs. S’assurer

que l’interrupteur se trouve à la position

d’arrêt avant de relier l’outil à une source

d’alimentation et/ou d’insérer un bloc-piles, de

ramasser ou de transporter l’outil. Transporter

un outil électrique alors que le doigt repose sur

l’interrupteur ou brancher un outil électrique dont

l’interrupteur est à la position de marche risque de

provoquer unaccident.

d ) Retirer toute clé de réglage ou clé avant de

démarrer l’outil. Une clé ou une clé de réglage

attachée à une partie pivotante de l’outil électrique

peut provoquer des blessurescorporelles.

e ) Ne pas trop tendre les bras. Conserver

son équilibre en tout temps. Cela permet

de mieux maîtriser l’outil électrique dans les

situationsimprévues.

f ) S’habiller de manière appropriée. Ne pas porter

de vêtements amples ni de bijoux. Garder les

cheveux, les vêtements et les gants à l’écart des

pièces mobiles. Les vêtements amples, les bijoux ou

les cheveux longs risquent de rester coincés dans les

piècesmobiles.

g ) Si des composants sont fournis pour le

raccordement de dispositifs de dépoussiérage

et de ramassage, s’assurer que ceux-ci sont bien

raccordés et utilisés. L’utilisation d’un dispositif de

dépoussiérage peut réduire les dangers engendrés par

lespoussières.

La page charge ...

Craftsman CMCCS660E1 Mode d'emploi

Marque: Craftsman

Modèle: CMCCS660E1

Catégorie: Tronçonneuses électriques

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Craftsman CMCCS660E1 Operating instructions
español: Craftsman CMCCS660E1 Instrucciones de operación

Craftsman CMCCS660E1 Mode d'emploi

Craftsman CMCCS660E1 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents