Scotts LCS31224S Le manuel du propriétaire

Marque: Scotts

Modèle: LCS31224S

Catégorie: Outils de jardin

Taper: Le manuel du propriétaire

OPERATOR’S MANUAL

CORDLESS 24 VOLT CHAIN SAW/LITHIUM-ION BATTERY PACK

Model LCS31224S

Your chain saw has been engineered and manufactured to our high standard for dependability, ease of

operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual

before using this product.

Thank you for your purchase.

DO NOT RETURN THIS PRODUCT TO THE STORE. OPERATING, ASSEMBLY, PART,

SERVICE QUESTIONS? GO TO SCOTTS.AMERICANLAWNMOWER.COM OR CALL

1-800-618-7474 BETWEEN 8:00AM-5:00PM EST FOR ASSISTANCE.

SAVE THIS MANUAL FOR FUTURE REFERENCE

ADD OIL TO OIL RESERVOIR BEFORE FIRST USE.

CA Compliant Charger Included (Model No. CHL90024)

BATTERY MUST BE CHARGED BEFORE

FIRST USE. TWO TO THREE INITIAL

CHARGING/DISCHARGING CYCLES MAY

BE REQUIRED TO ACHIEVE MAXIMUM

RUN TIME/CAPACITY.

GENERAL POWER TOOL SAFETY WARNINGS

IMPORTANT SAFETY WARNINGS

WARNING: Read all safety warnings and instructions. Failure to

follow the warnings and instructions may result in electric shock, fire

and/or serious injury.

Save all warnings and instructions for future reference. The term

“power tool” in the warnings refers to your mains-operated

(corded) power tool or battery-operated (cordless) power tool.

Work area safety

 Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

 Do not operate power tools in explosive atmospheres, such

as in the presence of flammable liquids, gases or dust. Power

tools create sparks which may ignite the dust or fumes.

 Keep children and bystanders away while operating a power

tool. Distractions can cause you to lose control.

Electrical safety

 Power tool plugs must match the outlet. Never modify the

plug in any way. Do not use any adapter plugs with earthed

(grounded) power tools. Unmodified plugs and matching outlets

will reduce risk of electric shock.

 Avoid body contact with earthed or grounded surfaces such

as pipes, radiators, ranges and refrigerators. There is an

increased risk of electric shock if your body is earthed or

grounded.

 Do not expose power tools to rain or wet conditions. Water

entering a power tool will increase the risk of electric shock.

 Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away from

heat, oil, sharp edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

 When operating a power tool outdoors, use an extension

cord suitable for outdoor use. Use of a cord suitable for

outdoor use reduces the risk of electric shock.

 If operating a power tool in a damp location is unavoidable,

use a ground fault circuit interrupter (GFCI) protected

supply. Use of a GFCI reduces the risk of electric shock.

Personal safety

 Stay alert, watch what you are doing and use common sense

when operating a power tool. Do not use a power tool while

you are tired or under the influence of drugs, alcohol or

medication. A moment of inattention while operating power tools

may result in serious personal injury.

 Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protection used for appropriate

conditions will reduce personal injuries.

 Prevent unintentional starting. Ensure the switch is in the

off-position before connecting to power source and/or

battery pack, picking up or carrying the tool. Carrying power

tools with your finger on the switch or energising power tools that

have the switch on invites accidents.

 Remove any adjusting key or wrench before turning the

power tool on. A wrench or a key left attached to a rotating

part of the power tool may result in personal injury.

 Do not overreach. Keep proper footing and balance at all

times. This enables better control of the power tool in

unexpected situations.

 Dress properly. Do not wear loose clothing or jewellery.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewellery or long hair can be caught in

moving parts.

 If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

Power tool use and care

 Do not force the power tool. Use the correct power tool for

your application. The correct power tool will do the job better

and safer at the rate for which it was designed.

 Do not use the power tool if the switch does not turn it on

and off. Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

 Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

 Store idle power tools out of the reach of children and do

not allow persons unfamiliar with the power tool or these

instructions to operate the power tool. Power tools are

dangerous in the hands of untrained users.

 Maintain power tools. Check for misalignment or binding

of moving parts, breakage of parts and any other

condition that may affect the power tool’s operation. If

damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

 Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind and

are easier to control.

 Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into account

the working conditions and the work to be performed. Use

of the power tool for operations different from those intended

could result in a hazardous situation.

Battery tool use and care

 Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type of battery

pack may create a risk of fire when used with another battery

pack.

 Use power tools only with specifically designated battery

packs. Use of any other battery packs may create a risk of

injury and fire.

TO REDUCE RISK OF INJURY:

Before any use, be sure everyone using this tool reads and

understands all safety instructions and other information

contained in this manual.

CAUTION: Wear appropriate personal hearing protection

during use. Under some conditions and duration of use, noise

from this product may contribute to hearing loss.

Save these instructions and review frequently prior to use

and in instructing others.

WARNING: When using electric gardening appliances,

basic safety precautions should always be followed to

reduce risk of fire, electric shock, and personal injury,

including the following:

READ ALL INSTRUCTIONS

CHAIN SAW SAFETY WARNINGS

 Keep all parts of the body away from the saw chain when the

chain saw is operating. Before you start the chain saw, make

sure the saw chain is not contacting anything. A moment of

inattention while operating chain saws may cause entanglement of

your clothing or body with the saw chain.

 Always hold the chain saw with your right hand on the rear

handle and your left hand on the front handle. Holding the

chain saw with a reversed hand configuration increases the risk of

personal injury and should never be done.

 Hold the power tool by insulated gripping surfaces only,

because the saw chain may contact hidden wiring. Saw chains

contacting a livewire may make exposed metal parts of the power

tool liveand could give the operator an electric shock.

 Wear safety glasses and hearing protection. Further

protective equipment for head, hands, legs and feet is

recommended. Adequate protective clothing will reduce personal

injury by flying debris or accidental contact with the saw chain.

 Do not operate a chain saw in a tree. Operation of a chain saw

while up in a tree may result in personal injury.

 Always keep proper footing and operate the chain saw only

when standing on fixed, secure and level surface. Slippery or

unstable surfaces such as ladders may cause a loss of balance or

control of the chain saw.

 When cutting a limb that is under tension be alert for spring

back. When the tension in the wood fibres is released the spring

loaded limb may strike the operator and/or throw the chain saw out

of control.

 Use extreme caution when cutting brush and saplings. The

slender material may catch the saw chain and be whipped toward

you or pull you off balance.

 Carry the chain saw by the front handle with the chain saw

switched off and away from your body. When transporting or

storing the chain saw always use the guide bar cover. Proper

handling of the chain saw will reduce the likelihood of accidental

contact with the moving saw chain.

 Follow instructions for lubricating, chain tensioning and

changing accessories. Improperly tensioned or lubricated chain

may either break or increase the chance for kickback.

 Keep handles dry, clean, and free from oil and grease. Greasy,

oily handles are slippery causing loss of control.

 Cut wood only. Do not use chain saw for purposes not

intended. For example: do not use chain saw for cutting

plastic, masonry or non-wood building materials. Use of the

chain saw for operations different than intended could result in a

hazardous situation.

Causes and operator prevention of kickback:

Kickback may occur when the nose or tip of the guide bar touches an

object, or when the wood closes in and pinches the saw chain in the cut.

Tip contact in some cases may cause a sudden reverse reaction, kicking

the guide bar up and back towards the operator.

Pinching the saw chain along the top of the guide bar may push the

guide bar rapidly back towards the operator.

Either of these reactions may cause you to lose control of the saw which

could result in serious personal injury. Do not rely exclusively upon the

safety devices built into your saw. As a chain saw user, you should take

several steps to keep your cutting jobs free from accident or injury.

Kickback is the result of tool misuse and/or incorrect operating

procedures or conditions and can be avoided by taking proper

precautions as given below:

 Maintain a firm grip, with thumbs and fingers encircling the

chain saw handles, with both hands on the saw and position

your body and arm to allow you to resist kickback forces.

Kickback forces can be controlled by the operator, if proper

precautions are taken. Do not let go of the chain saw.

 Do not overreach and do not cut above shoulder height. This

helps prevent unintended tip contact and enables better control of

the chain saw in unexpected situations.

 Only use replacement bars and chains specified by the

manufacturer. Incorrect replacement bars and chains may cause

chain breakage and/or kickback.

 Follow the manufacturer’s sharpening and maintenance

instructions for the saw chain. Decreasing the depth gauge

height can lead to increased kickback.

GENERAL POWER TOOL SAFETY WARNINGS

 When battery pack is not in use, keep it away from other met-

al objects, like paper clips, coins, keys, nails, screws or other

small metal objects, that can make a connection from one

terminal to another. Shorting the battery terminals together may

cause burns or a fire.

 Under abusive conditions, liquid may be ejected from the

battery; avoid contact. If contact accidentally occurs, flush

with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause irritation

or burns.

Service

 Have your power tool serviced by a qualified repair person

using only identical replacement parts. This will ensure that

the safety of the power tool is maintained.

 When servicing a power tool, use only identical

replacement parts. Follow instructions in the Maintenance

section of this manual. Use of unauthorized parts or failure to

follow Maintenance instructions may create a risk of shock or

injury.

WARNING: California Proposition 65: This product contains

chemicals known to the State of California to cause cancer, birth

defect or other reproductive harm.

WARNING: Some dust and debris created by the use of this tool

could contain chemicals known to the State of California to cause

cancer and birth defects or other reproductive harm. Some

examples of these chemicals are:

 Chemicals in fertilizers

 Compounds in insecticides, herbicides and

pesticides

 Arsenic and chromium from chemically treated lumber

Your risk from exposure to these chemicals varies, depending on how

often you do this type of work. To reduce your exposure, work in a

well-ventilated area and with approved safety equipment, such as dust

masks that are specially designed to filter out microscopic particles.

WARNING: Cancer and Reproductive Harm -

www.P65Warnings.ca.gov.

FEATURES

PRODUCT SPECIFICATIONS

LCS31224S

Input………………………………....24 V/2.0 Ah, DC Only

Bar Length………………………………....12” Oregon Bar

Chain…………………...……………....91PJ045X/Oregon

Weight………………….…………………………… 8.6 lbs.

Oil Capacity………………………………………… 210 ml

- Automatic oiling pump system—Protective bar cover—Rubber over molded handle -

TRIGGER SWITCH

REAR HANDLE

OIL TANK CAP

FRONT HANDLE

HAND GUARD

CHAIN

GUIDE BAR

GUIDE BAR COVER

LOCK KNOB

BATTERY PACK

TRIGGER RELEASE BUTTON

CHAIN TENSIONER

CHARGING THE BATTERY PACK

When fully charged, the battery can be safety stored in temperatures

down to –4° degrees F for a period of up to four weeks, before

requiring charging. Fully charge battery pack every 90 days.

If over a period of time the battery pack quickly runs down after a full

75 minutes charging period, a replacement battery pack is needed.

To prevent permanent damage to the battery, never store in a

discharged condition.

WINTER STORAGE—Fully recharge before storage and then again

every 90 days.

Since the battery will not develop a memory, it does not have to be

fully discharged before recharging.

A small leakage of liquid from the battery cells may occur under

extreme usage, charging or temperature conditions. This does

not indicate a failure. However, if the outer seal is broken and this

leakage gets on your skin.

a. Wash quickly with soap and water.

b. Neutralize with a mild acid such as lemon juice or

vinegar.

c. If the battery liquid gets in your eyes, flush them with

clean water for a minimum of 10 minutes and seek

immediate medical attention.

Charge the battery pack only with the charger provided.

Allow at least 75 minutes of charge time before initial use of the

chain saw.

Make sure the power supply is normal household voltage,

120volts, 60Hz, AC only.

The battery charger should be operated in temperatures between

39 and 104 degrees F.

The battery should be charged in a cool, dry place.

2 to 3 initial charging/discharging cycles may be required to

achieve maximum run time/capacity.

Do not attempt to open the charger or the unit. There are no

customer serviceable parts inside. Call the customer service help

line at 1-800-618-7474 for assistance.

DO NOT incinerate battery packs even if they are severely

damaged or completely worn out. They can explode in a fire

causing injury.

Use the battery charger indoors only.

Disconnect charger from the power supply when not in use to

prevent damage to the charger during a power surge.

TO CHARGE—SEE CHARGER MANUAL FOR COMPLETE INSTRUCTIONS

BATTERY DISPOSAL

Remove the battery pack from the chain saw. Cover the terminals with heavy duty adhesive tape. Do not attempt to destroy or disassemble battery

pack or remove any components. This product contains lithium-ion batteries which must be recycled or disposed of properly. Local, state or federal

laws may prohibit disposal of these batteries in ordinary trash.

The RBRC seal on the li-ion battery pack indicates that the costs to recycle the battery pack at the end of its useful life has already been

paid by The Great States Corporation American Lawn Mower Company. It is illegal to place spent li-ion batteries in the local municipal

solid waste or in the trash. RBRC in cooperation with The Great States Corporation American Lawn Mower Company has provided an

environmentally friendly and easy way to recycle spent li-ion batteries. Just contact your local recycling center or call 1-800-8BATTERY

for information on where to drop off the spent battery.

Charger and battery pack

Constant Red = Battery is charging

Constant Green = Battery is fully

charged.

Charger

Battery pack

INSTALLING AND REMOVING BATTERY PACK FROM THE UNIT

Place the battery pack in your chain saw (see picture). Ensure the

battery is securely connected to chain saw. To remove battery,

depress release button and slide battery pack out of tool.

ASSEMBLY

UNPACKING

This product requires no assembly.

Carefully remove the product and any accessories from the

box. Make sure that all items listed in the packing list are

included.

Inspect the product carefully to make sure no breakage or

damage occurred during shipping.

Do not discard the packing material until you have carefully

inspected and satisfactorily operated the product.

WARNING: If any parts are damaged or missing, do not

operate this product until the parts are replaced. Failure to

heed this warning could result in serious personal injury.

If any parts are damaged or missing, please call

1-800-618-7474 for assistance.

PACKING LIST

 Chain Saw with Blade Cover

 Charger and Battery Pack

 Operator’s Manual

INSTALLING/REPLACING THE GUIDE BAR AND CHAIN

DANGER: Never start the motor before installing the guide

bar, chain, chain cover and chain cover lock knob. Without

all these parts in place, the clutch can fly off or explode,

exposing the user to possible serious injury.

WARNING: To avoid serious personal injury, read and

understand all the safety instructions provided.

WARNING: Before performing any maintenance, remove

the battery pack from the saw. Failure to heed this warning

could result in serious personal injury.

CAUTION: Always wear gloves when handling the bar and

chain; these components are sharp and may contain burrs.

WARNING: Never touch or adjust the chain while the

motor is running. The saw chain is very sharp; always wear

protective gloves when performing maintenance to the

chain to avoid possible serious lacerations.

NOTE: When replacing the guide bar and chain, use only

identical replacement parts.

 Remove the battery from saw.

 Loosen the chain saw lock knob counterclockwise.

 Remove the chain cover.

 Remove the bar and chain from the mounting surface.

 Replace the chain cover and secure with the lock knob, but

leave the bar free to move for tension adjustment.

 Remove all slack from the chain by turning the chain

tensioner clockwise until the chain seats snugly against the

bar with the drive links in the bar groove.

 Tighten the knob.

The chain is correctly tensioned when there is no sag on the

underside of the guide bar, the chain is snug, but it can be

turned by hand without binding.

NOTE: If chain is too tight, it will not rotate. Loosen the knob

slightly and turn the chain tensioner 1/4 turn counterclockwise.

Lift the tip of the guide bar up and retighten the knob. Ensure

that the chain will rotate without binding.

NOTE: A new chain tends to stretch, check chain tension

frequently and tension as required.

INSTALLING/REPLACING THE GUIDE BAR AND CHAIN

 Remove the old chain from the bar.

 Lay out the new saw chain in a loop and straighten any links.

The cutters should face in the direction of the chain rotation.

If they face backwards, turn the loop over.

 Place the chain drive links into the bar groove.

NOTE: Make certain of the direction of the chain.

 Position the chain so there is a loop at the back of the bar.

 Hold the chain in position on the bar and place the loop

around the sprocket.

 Fit the bar flush against the mounting surface so that the bar

studs are in the long slot of the bar.

NOTE: When placing the bar on the bar studs, ensure that

the adjusting pin is in the chain tension pin hole.

OPERATING

TO TURN THE TOOL ON

Push the trigger release button in with your thumb and then

squeeze the trigger with your fingers. (Once the tool is

running, you can release the trigger release button). To

turn the tool OFF, release the trigger.

WARNING: To guard against injury, observe the following:

Read instruction manual before using,

Save instruction manual.

Keep hands away from chain.

Keep hands on handles. Don’t overreach.

A good, firm grip on the saw with both hands will help you

maintain control. Don’t let go. Grip the rear handle with your

right hand whether you are right or left handed. Wrap the

fingers of your left hand over and around the front handlebar,

and your left thumb under the front handlebar.

The following precautions should be followed to

minimize kickback:

1. Always grip the saw firmly with both hands. Hold the saw

firmly with both hands when the unit is running. Place

your right hand on the rear handle and your left hand on

the front handle with your thumbs and fingers encircling

the chain saw handles. A firm grip together with a stiff left

arm will help you maintain control of the saw if kickback

occurs.

2. Make sure that the area in which you are cutting is free

from obstructions. Do not let the nose of the guide bar

contact a log, branch, fence or any other obstruction that

could be hit while you are operating the saw.

3. Always cut with the unit running at full speed. Fully

squeeze the throttle trigger and maintain a steady cutting

speed.

Push and Pull – This reaction force is always opposite to the

direction the chain is moving where wood contact is made.

Thus, the operator must be ready to control the PULL when

cutting on the bottom edge of the bar, and PUSH when

cutting along the top edge.

Wear non-slip gloves for maximum grip and protection.

WARNING: Do not operate chain saw in a tree, on a ladder,

or on a scaffold; this is extremely dangerous.

CAUTION: Chain coasts after turned off.

Do not use under wet conditions.

Use extreme caution when cutting small size brush, saplings

or limbs under tension, because slender and tense material

may catch the saw and be whipped toward you, pull you off

balance or spring back.

Do not cut vines and/or small underbrush.

WARNING: Do not allow familiarity with this type of tool to

make you careless. Remember that a careless fraction of a

second is sufficient to inflict serious injury.

Before you start the unit, make sure the chain saw is not

contacting any object.

WARNING: Kickback may occur when the moving chain

contacts an object at the upper portion of the tip of the guide

bar or when the wood closes in and pinches the chain saw in

the cut. Contact at the upper portion of the tip of the guide

bar can cause the chain to dig into the object and stop the

chain for an instant. The result is a lightening fast, reverse

reaction which kicks the guide bar up and back toward the

operator. If the chain saw is pinched along the top of the

guide bar, the guide bar can be driven rapidly back toward

the operator. Either of these reactions can cause loss of

saw control which can result in serious injury. Do not rely

exclusively upon the safety devices built into the saw. As a

chain saw user, you should take several steps to keep your

cutting jobs free from accident or injury.

CUTTING INSTRUCTIONS

Make sure you follow the instructions in maintenance for

putting oil in the chain saw.

CAUTION: Chain oil reservoir must be filled before operation.

Failure to lubricate the chain will cause damage to the bar

and chain. Use only a goof quality bar and chain oil or, if not

available, unused SAE 30 weight motor oil may be substitut-

ed. One minute of use will consume approx 0.1 fl. Oz. (3ml) of

oil.

NOTE: It is normal for oil to seep from the saw when not in

use. To prevent seepage, empty the oil tank after each use.

When storing the unit for a long period of time (3 months or

longer) be sure the chain is lightly lubricated; this will prevent

rust on the chain and bar sprocket.

WARNING: Do Not use the chain saw with any type of

accessory or attachment. Such usage might be hazardous.

OPERATING

Proper Cutting Stance

Weight should be balanced with both feet on solid ground.

Keep left arm with elbow locked in a “straight arm” position to

withstand any kickback force.

Your body should always be to the left of the chain line.

Basic Cutting Procedure

Small trees up to 6-7inches in diameter are usually cut in

a single cut. Large trees require notch cuts. Notch cuts

determine the direction the tree will fall.

WARNING: If the tree starts to fall in the wrong direction, or if

the saw gets caught or hung up during the fall, leave the saw

and save yourself.

WARNING: Periodically glance at the top of the tree during

the back-cut to assure the tree is going to fall in the desired

direction.

Practice cutting a few small logs using the following technique

to get the “feel” of using the saw before you begin a major

sawing operation.

Take the proper stance in front of the wood with the saw off.

FELLING A TREE

When bucking and felling operations are being performed by

two or more persons, at the same time, the felling operation

should be separated from the bucking operation by a distance

of at least twice the height of the tree being felled. Trees

should not be felled in a manner that would endanger any

person, strike any utility line or cause any property damage.

If the tree does make contact with any utility line, the utility

company should be notified immediately.

WARNING: Check the tree for damaged or dead branches

that could fall and hit you during felling.

Before any cuts are started, pick your escape route (or routes

in case the intended route is blocked); clear the immediate

area around the tree and make sure there are no obstructions

in your planned path of retreat. A clear path of safe retreat

is approximately 135 degrees from planned line of fall. The

retreat path should extend back and diagonally to the rear of

the expected line of fall.

Before felling is started, consider the force and direction of the

wind, the lean and balance of the tree, and the location of large

limbs. These things influence the direction in which the tree will

fall. Do not try to fell a tree along a line different from its natural

line of fall.

The chain saw operator should keep on the uphill side of the

terrain as the tree is likely to roll or slide downhill after it is felled.

Remove dirt, stones, loose bark, nails, staples, and wire from the

tree where felling cuts are to be made.

NOTCHED UNDERCUT – Cut a notch about 1/3 diameter of the

tree, perpendicular to the direction of the fall. Make the cuts of

the notch so they intersect at a right angle to the line of fall. This

notch should be cleaned out to leave a straight line. To keep the

weight of the wood off the saw, always make the lower cut of the

notch before the upper cut.

WARNING: Do not fell trees during periods of high wind or heavy

precipitation. Wait to do your cutting until the hazard has ended.

WARNING: Do not cut down trees having an extreme lean

or large trees that have rotten limbs, loose bark, or hollow

trunks. Have these trees pushed or dragged down with heavy

equipment, then cut them up.

FELLING BACK-CUT

The back-cut is always made level and horizontal, and at a

minimum of 2 inches (5cm) above the horizontal cut of the notch.

Never cut through to the notch. Always leave a band of wood

between the notch and back-cut (approximately 2 inches (5cm)

or 1/10 the diameter of the tree). This is called “hinge” or “hinge

wood.” It controls the fall of the tree and prevents slipping or

twisting or shoot-back of the tree off the stump.

On large diameter trees, stop the back cut before it is deep

enough for the tree to either fall or settle back on the stump.

Then insert soft wooden or plastic wedg-

es into the cut so they do not touch the

chain. The wedges can be driven in, little

by little, to help jack the tree over.

Squeeze the trigger and let the chain accelerate to full speed

before entering the cut.

Hold the saw firmly with both hands. Always keep your left

hand on the front handle and your right hand on the rear

handle so that your body is to the left of the chain line.

Keep the unit running the entire time you are cutting, maintain

a steady speed.

Allow the chain to cut for you; exert only light downward

pressure. If you force the cut, damage to the bar, chain, or

unit can result.

Do not put pressure on the saw at the end of the cut.

When felling a tree, keep everyone a safe distance from the

cutting area. During felling operations, the safe distance

should be at least twice the height of the largest trees in the

felling area. If the tree makes contact with any utility line, the

utility company should be notified immediately.

Always cut with both feet on solid ground to prevent being

pulled off balance.

Do not cut above chest height, as a saw held higher is difficult

to control against kickback forces.

WARNING: Check the tree for damaged or dead branches

that could fall and hit you during felling.

WARNING: Do not cut trees near electrical wires or buildings.

OPERATING

LIMBING

Limbing is removing branches from a fallen tree.

Work slowly, keeping both hands on the chain saw with a firm

grip. Always make sure your footing is secure and your weight

is distributed evenly on both feet.

Leave the larger support limbs under the tree to keep the tree

off the ground while cutting.

Limbs should be cut one at a time. Remove the cut limbs from

the work area often to help keep the work area clean and safe.

Branches under tension should be cut from the bottom up to

avoid binding the chain saw.

Keep the tree between you and the chain saw while limbing.

Cut from the side of the tree opposite the branch you are

cutting.

WARNING: Never climb into a tree to limb or prune. Do not

stand on ladders, platforms, a log, or in any position which can

cause you to lose your balance or control of the saw.

PRUNING

Pruning is trimming limbs from a live tree.

Work slowly, keeping both hands on the chain saw with a firm

grip. Always make sure your footing is secure and your weight

is distributed evenly on both feet.

When pruning trees it is important not to make the finishing cut

next to the main limb or trunk until you have cut off the limb

further out to reduce the weight. This prevents stripping the

bark from the main member.

Under-buck the branch 1/3 through for your first cut.

Your second cut should over-buck to drop the branch off.

Now make your finishing cut smoothly and neatly against the

main member so the bark will grow back to seal the wound.

SPRINGPOLES

A springpole is any log, branch, rooted stump, or sapling

which is bent under tension by other wood so that it springs

back if the wood holding it is cut or removed. On a fallen tree,

a rooted stump has a high potential of springing back to the

upright position during the bucking cut to separate the log from

the stump. Watch out for springpoles, they are dangerous.

They could result in severe or fatal injury.

As the tree starts to fall, stop the chain saw and put it down

immediately. Retreat along the cleared path, but watch

the action in case something falls your way. Be alert for

overhead limbs or branches that may fall and watch your

footing.

WARNING: Never cut through to the notch when making

a back-cut. The hinge controls the fall of the tree, this is a

section of wood between the

notch and back-cut

BUCKING

Bucking is the term used for cutting a fallen tree to the

desired log length.

Always make sure your footing is secure and your weight is

distributed evenly on both feet.

Cut only one log at a time. Support small logs on a saw

horse or another log while bucking.

Keep a clear cutting area. Make sure that no objects can

contact the guide bar nose and chain during cutting, this can

cause kickback.

When bucking on a slope, always stand on the uphill side

of the log. To maintain complete control of the chain saw

when cutting through the log, release the cutting pressure

near the end of the cut without relaxing your grip on the

chain saw handles. Do not let the chain contact the ground.

After completing the cut, wait for the saw chain to stop

before you move the chain saw. Always stop the motor

before moving from tree to tree.

BUCKING LOGS UNDER STRESS

When the log is supported along its entire length, it should

be cut from the top or over-bucking.

When the log is supported on one end, cut 1/3 diameter from

the underside or under-bucking. Then make the finishing cut

by over-bucking to meet the first cut.

As the log is being cut, it will tend to bend. The saw can

become pinched or hung in the log if you make the first cut

deeper than 1/3 of the diameter of the log.

Give special attention to logs under stress to prevent the bar

and chain from pinching.

OVERBUCKING – Begin on the top side of the log with

the bottom of the saw against the log; exert light pressure

downward. Note that the saw will tend to pull away from you.

UNDER-BUCKING – Begin on the under side of the log

with the top of the saw against the log; exert light pressure

upward. During under-bucking, the saw will tend to push

back at you. Be prepared for this reaction and hold the saw

firmly to maintain control.

CHAIN TENSION AND MAINTENANCE

CHAIN TENSION

Remove the battery before setting the chain tension. Make sure the

guide bar screw is loosened to finger tight, turn the chain tensioner

clockwise to tension the chain. A cold chain will be correctly tensioned

when there is no slack on the underside of the guide bar, the chain is

snug, but it can be turned by hand without binding.

Chain must be re-tensioned whenever the flats on the drive links hang

out of the bar groove.

During normal saw operation, the temperature of the chain will

increase. The drive links of a correctly tensioned warm chain will

hang approximately .050 in. (1.25mm) out of the bar groove. Be

aware that chain tensioned while warm, may be too tight upon

cooling. Check the “cold tension” before next use.

NOTE: A new chain tends to stretch, check chain tension frequently

and tension as required.

CHAIN MAINTENANCE

CAUTION: Remove the battery pack and make sure the chain has

stopped before you do any work on the saw.

For smooth and fast cutting, chain needs to be maintained properly.

The chain requires sharpening when the wood chips are small and

powdery, the chain must be forced through the wood during cutting,

or the chain cuts to one side. During maintenance of your chain

remember:

- Improper filing angle of the side plate can increase the risk of

severe kickback.

- Raker (depth gauge) clearance.

- Too low increases the potential for kickback.

- Not low enough decreases cutting ability.

- If cutter teeth have hit hard objects such as nails and stones, or

have been abraded by mud or sand on the wood, have service

dealer sharpen chain.

NOTE: Inspect the drive sprocket for wear or damage when

replacing the chain. If signs

of wear or damage are

present in the areas

indicated, have the drive

sprocket replaced. Call our

customer service help line at

1-800-618-7474 for

assistance.

HOW TO SHARPEN THE

CUTTERS

Be careful to file all cutters to the specified angles and to the same

length, as fast cutting can be obtained only when all cutters are

uniform.

Wear gloves for protection. Properly tension the chain prior to

sharpening. Refer to “Chain Tension Section” earlier in this manual.

Do all of your filing at the midpoint of the bar.

Use a 5/32 in. diameter round file and holder.

Keep the file level with the top plate of the tooth. Do not let the file

dip or rock. Using light

but firm pressure,

stroke towards the front

corner of the tooth.

Lift file away from the steel on each return stroke.

Put a few firm strokes on every

tooth. File all left hand cutters

in one direction. Then move to

the other side and file the right

hand cutters in the opposite

direction. Occasionally remove

filing from the file with a wire

brush.

WARNING: Improper chain sharpening increases the potential of

kickback.

WARNING: Failure to replace or repair damaged chain can cause

serious injury.

WARNING: The saw chain is very sharp, always wear protective

gloves when performing maintenance to the chain.

TOP PLATE FILING ANGLE

Correct 30 degrees – File holders are marked with guide marks to

align file properly to produce top plate angle.

Less than 30 degrees – for

cross cutting.

More than 30 degrees –

feathered edge dulls quickly.

SIDE PLATE ANGLE

Correct – 80 degrees produced

automatically if correct diameter file is used in file holder.

Hook – “Grabs” and dulls quickly.

Increases potential of kickback.

Results from using a file with a

diameter too small, or file held to

low.

Backward Slope – Needs too

much feed pressure, causes excessive wear to bar and chain.

Results from using a file with a diameter too large, or file held too

high.

DEPTH GAUGE CLEARANCE

The depth gauge should be

maintained at a clearance of .025

in. (0.6 mm). Use a depth gauge

tool for checking the depth gauge

clearances.

Every time the chain is filed, check

the depth gauge clearance

Use a flat file and a depth gauge

jointer to lower all gauges uniformly.

Depth gauge jointers are available

in .020 in. to .035 in. (0.5 mm to 0.9

mm). Use a .025 in. (0.6 mm) depth

gauge jointer. After lowering each

depth gauge, restore original shape

by rounding the front. Be careful not

to damage adjoining drive links with

the edge of the file.

Depth gauges must be adjusted with

the flat file in the same direction the

adjoining cutter was filed with the round file. Use care not to contact

cutter face with flat file when adjusting depth gauges.

Approx. .050 (1.25mm)

MAINTENANCE

BEFORE USING : Fill oil well with new quality bar and chain

oil, or if unavailable, unused SAE 30 weight motor oil may be

substituted.

If you drop the chain saw, carefully inspect it for damage.

If the blade is bent, housing cracked, or handles broken

or if you see any other condition that may affect the saw’s

operation, call our customer service line at 1-800-618-7474

for assistance.

Make sure the battery is detached from the unit, then use

only mild soap and a damp cloth to clean the tool. Never let

any liquid get inside the tool; never immerse any part of the

tool into a liquid.

IMPORTANT: To assure product SAFETY and RELIABILITY,

repairs, maintenance and adjustment should be performed by

a qualified individual always using identical replacement

parts.

CAUTION: Do not at any time let brake fluids, gasoline,

petroleum based products, penetrating oils, etc., come in

contact with plastic parts. They contain chemicals that can

damage, weaken or destroy plastic.

Ensure that the plastic bar cover is in place when storing.

Fertilizers and other garden chemicals contain agents which

greatly accelerate the corrosion of metals Do not store the

tool on or adjacent to fertilizers or chemicals.

For smooth and fast cutting, chain needs to be maintained

properly. The chain requires sharpening when the wood

chips are small and powdery, the chain must be forced

through the wood during cutting, or the chain cuts to one

side. Refer to instructions earlier in this manual for

instructions on properly sharpening the chain.

TROUBLESHOOTING

Possible Cause

- Battery not making contact

- Lock off button not fully operated

- Battery not installed properly

- Battery not charged

Possible Solution

-Check battery is fully inserted

-Check that lock off button is fully forward prior to moving trigger

-Check battery installation

-Check battery charging requirements

- Bar and chain running hot and

smoking

- Check tension for over-tight condition

- Chain oil tank empty

- Chain installed backwards

- Adjust chain tension

- Fill tank with chain oil

- Reverse chain so that cutters face the right direction

Call us first with questions about operating or maintaining your chain

saw at 1.800.618.7474 between 8:00 a.m. – 5:00 p.m. Eastern

Standard Time, or get assistance on scotts.americanlawnmower.com

CALL US FIRST !!

- Chain tension too tight

- Check guide bar and chain for damage

- Motor runs but chain is not rotating - Adjust chain tension

- Replace damaged bar and chain with identical replacement

parts.

LUBRICATION SYSTEM

The chain is automatically lubricated.

Use only new bar and chain oil or unused SAE 30 weight motor

oil may be substituted. Never use wasted oil, low quality oil, or

insufficient oil. This could damage the pump; the bar and the

chain which may result in serious personal injury. Check oil

level before each work session, refill if oil level is below the

minimum shown on the side of the oil level window.

If the lubrication system does not work properly, check if all

oil-ways are clean and free from obstructions. If it is still not

working, call our customer service help line at 1-800-618-7474

for assistance.

GUIDE BAR MAINTENANCE

When the guide bar shows signs of wear, reverse it on the saw

to distribute the wear for maximum bar life. The bar should be

cleaned every day of use and checked for wear and damage.

Feathering or burring of the bar rails is a normal process of bar

wear. Such faults should be smoothed with a file as soon as

they occur.

A bar with any of the following faults should be replaced.

 Wear inside the bar rails which permits the chain to lay over

sideways.

 Bent guide bar

 Cracked or broken rails

 Spread rails

In addition, guide bars with a sprocket at their tip must be

lubricated weekly with a grease syringe to extend the guide bar

life. Using a grease syringe, lubricate weekly in the lubricating

hole.

Turn the guide bar and check that the lubrication holes and

chain groove are free from obstructions.

Problem

- Unit does not run

CALL US FIRST !!

Call us first with questions about operating or maintaining your chain

saw at 1.800.618.7474 between 8:00 a.m. – 5:00 p.m. Eastern

Standard Time, or get assistance on scotts.americanlawnmower.com

PARTS AND SERVICE

24V LITHIUM-ION CORDLESS CHAINSAW MODEL NUMBER LCS31224S

Always mention the model number when ordering kits/items for this tool.

For parts or service, please call 1-800-618-7474 or visit us online at SCOTTS.AMERICANLAWNMOWER.COM.

Be sure to provide all relevant information when you call or visit.

REPAIR PARTS (KITS/ ITEMS)

The model/serial number of this tool is found on a plate or label attached to the housing. Please record the

serial number in the space provided below.

MODEL NUMBER LCS31224S___

SERIAL NUMBER_______________

1 2 3 4 5

7 8

No. Kit/Item Number Description QTY

1,2,3,4&5 LCS24-SCA-1 Sprocket cover assembly kit 1

6 LCS24-OTC-1 Oil cap assembly kit 1

7,8,9,10&11 LCS24-BCK-1 12" Bar and chain assembly kit LCS31224S 1

12 BL82420 24V battery 1

13 CHL90024 24V charger 1

OPERATOR’S MANUAL

CORDLESS 24 VOLT CHAIN SAW/LITHIUM-ION BATTERY PACK

SCOTTS WARRANTY POLICY

American Lawn Mower Company

The Great States Corporation

7444 Shadeland Station Way

In a continued commitment to improve quality, the Manufacturer reserves the right

to make component changes or design changes when necessary. Rev. 11/11/2018

 3 Year limited warranty on all Scotts 24V lithium ion power tools from date of purchase when used for personal,

household, or family use.

 1 Year limited warranty on all Scotts 24V lithium ion batteries and chargers from date of purchase when used for

personal, household, or family use.

The Great States Corp. (GSC) warrants to the original owner that this Scotts product and service part is free from defects

in materials and workmanship and agrees to repair or replace any defective product or part for the warranty period as

stated above.

 Warranty voided if used for commercial or industrial purposes or any other improper use as determined by GSC.

 Warranty does not include repairs necessary due to operator’s abuse or negligence (including overloading the product

beyond capacity or immersion in water), or the failure to assemble, operate, maintain or store the product according to

the instructions in the owner’s manual.

 This warranty does not cover

 Wear items, including but not limited to - drive belts & gears, tines, cutting blades, mower blades, saw chains,

mulching blades, blower fans, spool covers, trimmer line, blower and vacuum tubes, guide bars, high pressure

hoses, wheels, handles, augers, worn bags, power cables, and other items subject to wear over time.

 Wear on batteries, including but not limited to – drops, wear and breakage on charger, exposure to extreme

temperature swings (hot or cold), battery left on charger too long, battery left uncharged for too long, and misuse

or abuse of the battery.

 This warranty does not cover damage caused by cold, heat, rain, excessive humidity or other environmental extremes.

 This warranty does not cover normal deterioration of the exterior finish or normal wear and tear on the products

including, but not limited to scratches, cracks, dents, or damage caused by outside chemicals.

 This warranty is not transferable and only applies to new products sold directly from an authorized retailer. This

warranty does not apply to any product, new or used, purchased through unauthorized third-party channels. For

information on authorized dealers, contact our customer support hotline at 1-800-618-7474 (Mon-Fri 8am-5pm Est)

 Any incidental, indirect or consequential loss, damage, or expense that may result from any defect or malfunction of

the products is not covered by the warranty.

 The warranty does not include installation, assembly or normal adjustments explained in the operator’s manual. The

expense of delivering the product to the vendor and the expense of returning the product or replacement parts to the

owner is not covered by the warranty.

Additional Warranty Limitations

Some states do not allow the exclusion or limitation on how long an implied warranty lasts, so the above limitation may

not apply to you. Products sold damaged or incomplete, sold ―as is, or sold as reconditioned are not covered under the

warranty.

Damage or liability caused by shipping, improper handling, improper assembly, incorrect voltage, improper wiring,

improper maintenance, improper modification or the use of accessories and/or attachments not specifically recommended

is not covered by this warranty.

Proof of purchase, original dated sales receipt, must accompany all warranty claims.

For claims go to scotts.americanlawnmower.com or call our customer support hotline from 8am-5pm EST,

Mon-Fri at 1-800-618-7474

MOTOSIERRA DE BATERÍA DE 24 VOLTIOS DE LITIO-ION

MANUAL DEL OPERARIO

Modelo LCS31224S

Este producto ha sido diseñado y fabricado de acuerdo con nuestros altos estándares de confiabilidad, facilidad de operación

y seguridad para el operario. Si se trata con cuidado, esta herramienta le otorgará años de óptimo rendimiento y resistencia.

ADVERTENCIA: Para reducir el riesgo de sufrir alguna lesión, el usuario debe leer y comprender el manual del operario antes de usar este

producto.

Muchas gracias por su compra.

GUARDE ESTE MANUAL PARA CONSULTAS FUTURAS

NO DEVUELVA ESTE PRODUCTO A LA TIENDA. ¿TIENE PREGUNTAS SOBRE FUNCIONAMIENTO, MONTAJE, PIEZAS O SERVICIO

TÉCNICO? VAYA A SCOTTS.AMERICANLAWNMOWER.COM O LLAME AL 1-800-618-7474 ENTRE LAS 8:00 AM Y LAS 5:00 PM, HORA DEL

ESTE DE LOS ESTADOS UNIDOS.

Cargador Cumple con CA está incluido (Modelo No. CHL90024)

DEBE CARGAR LA BATERÍA ANTES DE

UTILIZARLA POR PRIMERA VEZ. ES

POSIBLE QUE SE NECESITEN DE DOS A

TRES CICLOS DE CARGA/ DESCARGA

INICIALES PARA OBTENER LA MÁXIMA

CAPACIDAD O TIEMPO DE

FUNCIONAMIENTO.

AGREGAR ACEITE AL RESERVORIO DE ACEITE ANTES DEL PRIMER USO.

ADVERTENCIAS DE SEGURIDAD IMPORTANTES

ADVERTENCIAS DE SEGURIDAD GENERALES PARA LA HERRAMIENTAS ELÉCTRICAS

ADVERTENCIA: Lea todas las advertencias de seguridad y las

instrucciones. La inobservancia de las advertencias e instrucciones

puede causar descargas eléctricas, incendios o lesiones graves.

Guarde todas las advertencias e instrucciones para consultarlas

en el future El término “herramienta eléctrica” en las advertencias se

refiere a las herramientas eléctricas que funcionan con corriente (con

cordón) o las que funcionan con batería (inalámbricas).

Área de trabajo

 Mantenga limpia y bien iluminada el área de trabajo. Un área

de trabajo mal despejada o mal iluminada propicia accidentes.

 No utilice herramientas motorizadas en atmósferas

explosivas, como las existentes alrededor de líquidos, gases

y polvos inflamables. Las herramientas eléctricas generan

chispas que pueden encender el polvo y los vapores inflamables.

 Mantenga alejados a los niños y circunstantes al maniobrar

una herramienta eléctrica. Toda distracción puede causar la

pérdida del control de la herramienta.

Seguridad eléctrica

 Las clavijas de las herramientas eléctricas deben

corresponder a las tomas de corriente donde se conectan.

Nunca modifique la clavija de ninguna forma. No utilice

ninguna clavija adaptadora con herramientas eléctricas

dotadas de contacto a tierra. Conectando las clavijas originales

en las tomas de corriente donde corresponden se disminuye el

riesgo de una descarga eléctrica.

 Evite el contacto del cuerpo con las superficies de objetos

conectados a tierra, como las tuberías, radiadores, estufas y

refrigeradores. Existe un mayor riesgo de descargas eléctricas

si el cuerpo está haciendo tierra.

 No exponga las herramientas eléctricas a la lluvia ni a

condiciones de humedad. La introducción de agua en una

herramienta eléctrica aumenta el riesgo de descargas eléctricas.

 No maltrate el cordón eléctrico. Nunca utilice el cordón para

trasladar, desconectar o tirar de la herramienta eléctrica.

Mantenga el cordón lejos del calor, aceite, bordes afilados y

piezas móviles. Los cordones eléctricos dañados o enredados

aumentan el riesgo de descargas eléctricas.

 Al utilizar una herramienta eléctrica a la intemperie, use un

cordón de extensión apropiado para el exterior. Usando un

cordón adecuado para el exterior se disminuye el riesgo de

descargas eléctricas.

 Si debe operar una herramienta en lugares húmedos, use un

suministro protegido por un interruptor de circuito con

pérdida a tierra (GFCI). El uso de un GFCI reduce el riesgo de

descargas eléctricas.

Seguridad personal

 Permanezca alerta, preste atención a lo que esté haciendo y

aplique el sentido común al utilizar herramientas eléctricas.

No utilice la herramienta eléctrica si está cansado o se

encuentra bajo los efectos de alguna droga, alcohol o

medicamento. Un momento de inatención al utilizar una

herramienta eléctrica puede causar lesiones corporales serias.

 Utilice protección el equipo otros. Siempre póngase

protección ocular. El uso de equipo protector como mascarilla

para el polvo, calzado de seguridad, casco y protección para los

oídos en las circunstancias donde corresponda disminuye el

riesgo de lesiones.

 Evite que la herramienta se active accidentalmente.

Asegúrese de que el interruptor esté en la posición de

apagado antes de conectar la herramienta a un suministro de

corriente o de colocar un paquete de baterías. Transportar

herramientas eléctricas con el dedo en el interruptor o enchufar

herramientas eléctricas que tienen el interruptor encendido puede

ocasionar accidentes.

 Retire toda llave o herramienta de ajuste antes de encender

la herramienta eléctrica. Toda llave o herramienta de ajuste

dejada en una pieza giratoria de la herramienta eléctrica puede

causar lesiones.

 No estire el cuerpo para alcanzar mayor distancia.

Mantenga una postura firme y buen equilibrio en todo

momento. De esta manera se logra un mejor control de la

herramienta eléctrica en situaciones inesperadas.

 Vístase adecuadamente. No vista ropas holgadas ni joyas.

Mantenga el cabello, la ropa y los guantes alejados de las

piezas móviles. Las ropas holgadas y las joyas, así como el

cabello largo, pueden engancharse en las piezas móviles.

 Si se suministran dispositivos para conectar mangueras de

extracción y captación de polvo, asegúrese de que éstas

estén bien conectadas y se usen correctamente. El uso de

la captación de polvo puede reducir los peligros relacionados

con éste.

Empleo y cuidado de la herramienta eléctrica

 No fuerce la herramienta eléctrica. Utilice la herramienta

eléctrica adecuada para cada trabajo. La herramienta

eléctrica adecuada efectúa mejor y de manera más segura el

trabajo, si además se maneja a la velocidad para la que está

diseñada.

 No utilice la herramienta si el interruptor no enciende o no

apaga. Cualquier herramienta eléctrica que no pueda

controlarse con el interruptor es peligrosa y debe repararse.

 Desconecte la clavija del suministro de corriente o retire el

paquete de baterías de la herramienta eléctrica, según sea

el caso, antes de efectuarle cualquier ajuste, cambiarle

accesorios o guardarla. Tales medidas preventivas de

seguridad reducen el riesgo de poner en marcha

accidentalmente la herramienta.

 Guarde las herramientas eléctricas desocupadas fuera del

alcance de los niños y no permita que las utilicen personas

no familiarizadas con las mismas o con estas

instrucciones. Las herramientas eléctricas son peligrosas en

manos de personas no capacitadas en el uso de las mismas.

 Preste servicio a las herramientas eléctricas. Revise para

ver si hay desalineación o atoramiento de piezas móviles,

ruptura de piezas o cualquier otra condición que pueda

afectar el funcionamiento de la herramienta. Si está dañada

la herramienta eléctrica, permita que la reparen antes de

usarla. Numerosos accidentes son causados por herramientas

eléctricas mal cuidadas.

 Mantenga las herramientas de corte afiladas y limpias. Las

herramientas de corte bien cuidadas y con bordes bien afilados,

tienen menos probabilidad de atascarse en la pieza de trabajo y

son más fáciles de controlar.

 Utilice la herramienta eléctrica, los accesorios y brocas,

hojas y cuchillas de corte, ruedas de esmeril, etc. de

conformidad con estas instrucciones, tomando en cuenta

las condiciones de trabajo y la tarea por realizar. Si se

utiliza la herramienta eléctrica para operaciones diferentes de

las indicadas podría originar una situación peligrosa.

Empleo y cuidado de la herramienta de baterías

 Sólo cargue el paquete de baterías con el cargador

especificado por el fabricante. Un cargador adecuado para

un tipo paquete de baterías puede significar un riesgo de

incendio si se emplea con un paquete de baterías diferente.

 Utilice las herramientas eléctricas sólo con los paquetes de

baterías específicamente indicados. El empleo de paquetes

de baterías diferentes puede presentar un riesgo de incendio.

PARA REDUCIR EL RIESGO DE LESIONES:

Antes de poner en uso la herramienta, asegúrese de que todos los

usuarios lean y comprendan las instrucciones de seguridad y la

demás información incluida en este manual.

PRECAUCIÓN: Use protección auditiva apropiada mientras trabaja.

En ciertas condiciones y con cierta duración de uso, el ruido generado

por este producto puede contribuir a la pérdida de la audición.

Guarde estas instrucciones y revíselas con frecuencia antes de usar

la herramienta y para impartirlas a otros.

ADVERTENCIA: Al utilizar aparatos eléctricos para el jardín, se

recomienda respetar las precauciones de seguridad básicas que se

detallan a continuación, a fin de reducir riesgos de incendios,

descargas eléctricas y lesiones personales.

LEA TODAS LAS INSTRUCCIONES

ADVERTENCIAS DE SEGURIDAD GENERALES PARA LA HERRAMIENTAS ELÉCTRICAS

 Cuando no esté utilizándose el paquete de baterías,

manténgalo lejos de otros objetos metálicos, como clips,

monedas, llaves, clavos, tornillos o otros objetos metálicos,

pequeños que puedan establecer conexión entre ambas

terminales. Establecer una conexión directa entre las dos

terminales de las baterías puede causar quemaduras o incendios.

 Si se maltratan las baterías, puede derramarse líquido de las

mismas; evite todo contacto con éste. En caso de contacto,

lávese con agua. Si el líquido llega a tocar los ojos, además

busque atención médica. El líquido de las baterías puede causar

irritación y quemaduras.

Servicio

 Permita que un técnico de reparación calificado preste

servicio a la herramienta eléctrica, y sólo con piezas de

repuesto idénticas. De esta manera se mantiene la seguridad

de la herramienta eléctrica.

 Al dar servicio a una herramienta eléctrica, sólo utilice

piezas de repuesto idénticas. Siga las instrucciones

señaladas en la sección Mantenimiento de este manual. El

empleo de piezas no autorizadas o el incumplimiento de las

instrucciones de mantenimiento puede significar un riesgo de

descarga eléctrica o de lesiones.

ADVERTENCIAS DE SEGURIDAD DE LA MOTOSIERRA

 Mantenga todas las partes del cuerpo alejadas de la

motosierra mientras esté en funcionamiento. Antes de

encender la motosierra, asegúrese de que no esté en

contacto con nada. Un momento de distracción mientras usa la

motosierra puede hacer que la motosierra agarre su ropa o una

parte de su cuerpo.

 Siempre sostenga la motosierra con la mano derecha en el

mango trasero y la mano izquierda en el mango delantero.

Sostener la motosierra con las manos invertidas aumenta el riesgo

de sufrir lesiones personales y siempre debe evitarse.

 Sostenga la herramienta eléctrica únicamente por las partes

aisladas, porque la misma podría morder cables ocultos. Si la

motosierra toca un cable vivo, las piezas metálicas de la

herramienta podrían energizarse y producirle una descarga

eléctrica al operador.

 Use gafas de seguridad y protección auditiva. También se

recomienda usar equipo de protección para la cabeza, las

manos, las piernas y los pies. La indumentaria de protección

adecuada reducirá las lesiones personales en caso de que salgan

partículas despedidas o su cuerpo toque accidentalmente la

motosierra.

 No use la motosierra sobre un árbol. Si usa la motosierra

subido a un árbol, podría sufrir lesiones personales.

 Siempre mantenga un buen apoyo y utilice la motosierra

únicamente sobre superficies fijas, firmes y niveladas. Las

superficies resbaladizas o inestables como las escaleras pueden

hacerle perder el equilibrio o el control de la motosierra.

 Cuando corte una rama que esté sometida a tensión, esté

atento al retorno. Cuando se libera la tensión de las fibras de

madera, la rama podría golpear al operador o lanzar la motosierra

en forma descontrolada.

 Tenga extremo cuidado al cortar maleza o retoños. El material

delgado podría quedar atrapado en la motosierra y salir disparado

hacia usted o hacerle perder el equilibrio.

 Transporte la motosierra apagada, lejos de su cuerpo y

tomada del mango frontal. Siempre que transporte o

almacene la motosierra, coloque la cubierta de la barra guía.

Manipular la motosierra correctamente reduce la probabilidad de

tocar accidentalmente la cadena en movimiento.

 Siga las instrucciones para lubricar la herramienta, tensionar

la cadena y cambiar los accesorios. Si la cadena no está

correctamente tensionada o lubricada, podría romperse o

presentar un mayor riesgo de que ocurra un contragolpe.

 Mantenga los mangos secos, limpios y sin aceite ni grasa. Los

mangos con aceite o grasa son resbaladizos y pueden hacerle

perder el control.

 Corte únicamente madera. No use la motosierra para usos

distintos de los previstos. Por ejemplo: no use la

motosierra para cortar plástico, mampostería ni materiales

de construcción que no sean de madera. El uso de la

motosierra para fines distintos de los previstos podría dar lugar

a una situación de riesgo.

Causas y prevención del contragolpe:

Puede ocurrir un contragolpe cuando la punta de la barra guía toca

un objeto o cuando la madera se cierra y pellizca la cadena de la

sierra en el punto de corte.

En algunos casos, el contacto de la pieza de trabajo con la punta de

la barra guía puede causar una reacción súbita en dirección inversa,

la cual lanza la barra guía hacia arriba y hacia atrás, en dirección al

operador.

El pellizcamiento de la cadena de la sierra en la parte superior de la

barra guía puede empujar la barra rápidamente hacia atrás, en

dirección al operador.

Cualquiera de estas dos reacciones puede causar la pérdida del

control de la sierra, lo cual a su vez puede producir lesiones

personales serias. No dependa exclusivamente de los dispositivos

de seguridad incorporados de la sierra. Como usuario de una

motosierra, debe tomar varias medidas para evitar los accidentes y

las lesiones en todos sus trabajos de corte.

El contragolpe es el resultado de un uso indebido de la herramienta

o de procedimientos o condiciones de utilización incorrectos, y se

puede evitar tomando las precauciones apropiadas que se presentan

a continuación:

 Mantenga la herramienta bien sujeta, con los pulgares y los

dedos alrededor de los mangos de la motosierra; sostenga

la herramienta con ambas manos y posicione su cuerpo y

su brazo de una forma que le permita resistir la fuerza de

un contragolpe. El operador puede controlar las fuerzas del

contragolpe si toma las precauciones adecuadas. No suelte la

motosierra.

 No se estire ni corte por encima de la altura del hombro.

Esto ayuda a evitar el contacto accidental con la punta y

permite un mejor control de la motosierra ante situaciones

inesperadas.

 Use únicamente barras y cadenas de repuesto indicadas

por el fabricante. El uso de barras y cadenas de repuesto

incorrectas podría hacer que la cadena se rompa o que se

produzcan contragolpes.

 Siga las instrucciones de afilado y mantenimiento de la

cadena de la sierra que provee el fabricante. Disminuir la

altura del calibrador de profundidad puede aumentar la

probabilidad de que ocurra un contragolpe.

ADVERTENCIA: Proposición 65 de California: Este producto

contiene sustancias químicas al estado de california como causantes

de cáncer, defectos de nacimiento u otros problemas reproductivos.

ADVERTENCIA: Parte del polvo y los desechos generados por el uso

de esta herramienta contienen químicos reconocidos por el Estado de

California como causantes de cáncer, defectos de nacimiento u otros

efectos nocivos para el aparato reproductor. Algunos ejemplos de

estos productos químicos son:

 químicos presentes en fertilizantes;

 compuestos presentes en insecticidas, herbicidas y pesticidas; y

 arsénico y cromo de maderas tratadas químicamente.

El riesgo que usted corre al exponerse a estos químicos varía según

la frecuencia con la que realiza este tipo de trabajo. Para reducir la

exposición, trabaje en una zona bien ventilada y utilice equipo de

protección aprobado, como mascarillas antipolvo especialmente

diseñadas para filtrar partículas microscópicas.

ADVERTENCIA: Cáncer y Daño Reproductivo -

www.P65Warnings.ca.gov.

CARACTERÍSTICAS

ESPECIFICACIONES DEL PRODUCTO

LCS31224S

Entrada ……………………………………….…....24 V/2.0 Amp horas, CC Solamente

Longitud de la barra Barra Oregon……….…...Barra Oregon de 30,5 cm (12 pulg)

Cadena ……...……...…………………………………..………………91PJ045X/Oregon

Peso ………….....………………………………………………………. 3.9 kg (8.6 libras)

Capacidad de aceite………………………………………………………………. 210 ml

- Lubricación automática de la barra y la cadena - Protector de barra - Mango de caucho sobremoldeado -

INTERRUPTOR DE GATILLO

MANGO

TRASERO

TAPA DEL TANQUE

DE ACEITE

MANGO

DELANTERO

PROTECTOR MANUAL

CADENA

BARRA

PROTECTOR

DE BARRA

PERILLA DE

SEGURIDAD

PAQUETE DE BATERÍAS

BOTÓN DE DESBLOQUEO

DEL GATILLO

TENSOR DE

LA CADENA

CARGA DEL PAQUETE DE BATERÍAS

Cuando la batería está cargada por completo, se puede almacenar

de forma segura en temperaturas de hasta –20 ºC (-4 ºF) durante un

período de quatros semanas antes de que requiera una nueva carga.

Cargue el paquete de baterías completamente cada 90 días.

Si transcurrido un tiempo determinado, el paquete de baterías se

agota rápidamente después de un período de carga de 75 minutos,

es necesario un cambio de batería.

Para prevenir un daño permanente a la batería, nunca la almacene

descargada.

ALMACENAMIENTO EN INVIERNO. Recargue la batería

completamente durante 75 minutos antes de guardarla y repita la

operación cada 90 días.

Debido a que la batería no tiene ningún efecto memoria, no es

necesario que esté totalmente descargada para volver a cargarla.

Es posible que ocurra una pequeña pérdida de líquido de las pilas

en condiciones de uso, carga o temperaturas extremas. Esto no indica

una falla. No obstante, si el sello externo está roto y el líquido entra en

contacto con la piel:

a. Lávese con agua y jabón de inmediato.

b. Neutralice el efecto con un ácido débil como jugo de limón

o vinagre.

c. Si el líquido de la batería penetra en los ojos, enjuáguese con

agua limpia durante un mínimo de 10 minutos y obtenga asistencia

médica inmediata.

Cargue el paquete de baterías únicamente con el cargador provisto.

Deje por lo menos 75 minutos de tiempo de carga antes del primer

uso de la motosierra.

Asegúrese de que el voltaje del suministro eléctrico sea el doméstico

normal: 120 voltios, 60 Hz, CA únicamente.

El cargador de baterías debe funcionar en temperaturas que oscilen

entre los 4 y 40 ºC (39 y 104 ºF).

La batería debe cargarse en un lugar fresco y seco.

Es posible que se necesiten de dos a tres ciclos de carga/

descarga iniciales para obtener la máxima capacidad o tiempo

de funcionamiento.

No intente abrir el cargador ni la unidad, ya que en su interior no

existen piezas que el usuario pueda reparar. Comuníquese con

nuestra línea de ayuda de atención al 1-800-618-7474 para recibir

asistencia.

NO incinere los paquetes de baterías, aunque estén muy dañados o

totalmente agotados, porque pueden estallar y provocar lesiones.

Utilice el cargador de baterías sólo bajo techo.

Desconecte el cargador del suministro eléctrico cuando no esté

en uso para evitar daños en caso de que se produzca un pico de

tensión.

PROCEDIMIENTO DE CARGA

ELIMINACIÓN DE LA BATERÍA

Extraiga el paquete de baterías de la herramienta. Cubra los terminales con una cinta adhesiva resistente. No trate de destruir ni desarmar el

paquete de baterías ni de extraer ninguno de sus componentes. Este producto contiene baterías de litio-ion, que se deben reciclar o desechar

adecuadamente. Es posible que las leyes locales, estatales o federales prohíban eliminar estas baterías con los desechos comunes.

El sello RBRC que aparece en el paquete de baterías de litio-ion indica que los costos para reciclarlo al término de su vida útil ya han

sido pagados por The Great States Corporation/American Lawn Mower Company. Es ilegal arrojar las baterías de litio-ion gastadas en

un depósito municipal de residuos sólidos o en la basura. RBRC, en colaboración con The Great States Corporation/American Lawn

Mower Company, ofrece una forma fácil y ecológica de reciclar las baterías de litio-ion gastadas. Simplemente comuníquese con un

centro de reciclaje local o llame al 1.800.8.BATTERY para obtener información sobre dónde dejar las baterías gastadas.

CARGADOR Y PAQUETE DE BATERÍAS

Cargador

Paquete de

baterías

INSTALACIÓN DEL PAQUETE DE BATERÍAS EXTRACCIÓN DEL

PAQUETE DE BATERÍAS

Coloque el paquete de baterías en su motosierra (observe la ilustración).

Asegúrese de que los enganches baterías calcen perfectamente y que la

batería quede conectada a la motosierra con firmeza.

Luz roja constante = La batería

es está cargando

Luz verde constante = La batería

se cargó por completo

INSTALACIÓN / REEMPLAZO DE LA BARRA GUÍA Y LA CADENA

PELIGRO: Nunca encienda el motor antes de instalar la barra

guía, la cadena y la tapa de la cadena. Si estas piezas no están

en su lugar, el embrague puede salir disparado o explotar, lo que

expondrá al usuario a una posible lesión grave.

ADVERTENCIA: Para evitar lesiones personales graves, lea y

comprenda las instrucciones de seguridad provistas.

ADVERTENCIA: Antes de realizar alguna tarea de mantenimiento,

asegúrese de retirar el paquete de baterías. De lo contrario, podría

sufrir lesiones personales de gravedad.

PRECAUCIÓN: Use siempre guantes al manipular la barra y la

cadena. Estos componentes son filosos y pueden contener rebabas.

ADVERTENCIA: Nunca toque o ajuste la cadena mientras el

motor está en funcionamiento. La cadena de la motosierra es

muy filosa; por lo tanto, siempre utilice guantes de protección

al realizar el mantenimiento de la cadena para evitar posibles

laceraciones graves

NOTA: Use únicamente piezas de reemplazo idénticas al

reemplazar la barra guía y la cadena.

 Extraiga el paquete de baterías de la motosierra.

 Afloje la perilla de seguridad de la motosierra en sentido

contrario a las agujas del reloj.

 Retire la tapa de la cadena.

 Retire la barra y la cadena de la superficie de montaje.

MONTAJE

DESEMBALAJE

Este producto requiere no montaje.

Extraiga la herramienta y los accesorios de la caja con cuidado.

Asegúrese de que estén incluidos todos los elementos detallados

en la lista de embalaje.

Inspeccione el producto detenidamente para corroborar que no

existan roturas ni averías ocurridas durante el envío.

No deseche el material de embalaje hasta haber inspeccionado

exhaustivamente el producto y comprobar que funciona en forma

satisfactoria.

ADVERTENCIA: Si falta alguna pieza o está dañada, no utilice este

producto hasta reponer la pieza en cuestión. De lo contrario, podría

sufrir lesiones personales de gravedad.

Si falta alguna pieza o está dañada, llame al 1-800-618-7474 para

obtener asistencia.

LISTA DE EMBALAJE

 Motosierra con funda de cuchillas

 Paquete de baterías y cargador

 Manual del operario

La page est en cours de chargement...

Scotts LCS31224S Le manuel du propriétaire

Marque: Scotts

Modèle: LCS31224S

Catégorie: Outils de jardin

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Scotts LCS31224S Owner's manual
español: Scotts LCS31224S El manual del propietario

Scotts LCS31224S Le manuel du propriétaire

Scotts LCS31224S Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents