Danby DAC080B6IWDB-6 Le manuel du propriétaire

DANBY PRODUCTS LIMITED, ONTARIO, CANADA N1H 6Z9

DANBY PRODUCTS INC., FINDLAY, OHIO, USA 45840

OWNER’S MANUAL

MANUEL DU PROPRIÉTAIRE

MANUAL DEL PROPIETARIO

www.Danby.com

*

AIR CONDITIONER

Owner’s Manual.............................1 - 26

CLIMATISEUR

Manuel du propriétaire.................27 - 52

AIRE ACONDICIONADO

Manual del propietario.................53 - 78

MODEL * MODÈLE * MODELO

DAC080B6IWDB-6

DAC100B6IWDB-6

DAC120B6IWDB-6

2021.02.26

1

Welcome to the Danby family.

We are proud of our quality products and we believe in dependable service. We suggest

that you read this owner’s manual before plugging in your new appliance as it contains

important operation information, safety information, troubleshooting, and maintenance tips

to ensure the reliability and longevity of your appliance.

You are entitled to the warranty coverage as described in the owner’s manual provided with

your new appliance.

1. Please write down your appliance information below. You must keep the original proof

of purchase receipt to validate and receive warranty services.

2. Register your product online and receive a FREE 2 MONTH WARRANTY EXTENSION

after ﬁ lling out a product survey, at www.danby.com/support/product-registration/

Need Help?

1. Read your Owner’s Manual for installation help, troubleshooting, and maintenance

assistance.

2. Visit www.Danby.com to access self-service tools, FAQs and much more by searching

your model number in the search bar.

3. For the Quickest Customer Service, please ﬁ ll out the web form at www.danby.com/

support. Your submission will go directly to an expert on your particular appliance.

Our average response times are between 20 minutes and 2 hours, during EST business

hours.

4. Call 1-800-263-2629 - please note that during peak hours, hold times can exceed one

hour.

Model Number: ____________________________________________________

Serial Number: ____________________________________________________

Date of Purchase: __________________________________________________

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

CAUTION: RISK OF FIRE

Flammable refrigerant used. When maintaining

or disposing of the air conditioner, the refrigerant

must not be allowed to vent into the open air.

WARNING Shows that the appliance uses a ﬂ ammable refrigerant. If the

refrigerant leaks and is exposed to an external ignition source, there is

a risk of ﬁ re.

CAUTION Shows that the operation manual should be read carefully.

CAUTION Shows that service personnel should be handling this equipment with

reference to the installation manual.

CAUTION Shows that the information is available such as the operating manual

or the installation manual.

SAVE THESE INSTRUCTIONS!

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAFETY PRECAUTIONS

WARNING

• Installation must be performed according to the installation instructions. Improper installation can cause

water leakage, electrical shock or ﬁ re.

• Use only the included accessories and parts and speciﬁ ed tools for the installation. Using non-standard

parts can cause water leakage, electrical shock, ﬁ re and injury or property damage.

• Make sure that the outlet you are using is grounded and has the appropriate voltage. The power cord

is equipped with a three-prong grounding plug to protect against shock. Voltage information can be

found on the nameplate of the unit.

• You unit must be used in a properly grounded wall receptacle. if the wall receptacle you intend to use is

not adequately grounded or protected by a time delay fuse or circuit breaker (the fuse of circuit breaker

needed is determined by the maximum current of the unit. The maximum current is indicated on the

nameplate located on the unit), have a qualiﬁ ed electrician install the proper receptacle.

• Install the unit on a ﬂ at, sturdy surface. Failure to do so could result in damage or excessive noise and

vibration.

• The unit must be kept free from obstruction to ensure proper function and to mitigate safety hazards.

• Do not modify the length of the power cord or use an extension cord to power the unit.

• Do not share a single outlet with other electrical appliances. Improper power supply can cause ﬁ re or

electrical shock.

• Do not install you air conditioner in a wet room such as a bathroom or laundry room. Too much

exposure to water can cause electrical components to short circuit.

• Do not install the unit in a location that may be exposed to combustible fas as this could cause ﬁ re.

• The unit has wheels to facilitate moving. Make sure not to use the wheels on thick carpet or to roll over

objects as this could cause tipping.

• Do not operate a unit that been dropped or damaged.

• The appliance with the electric heater shall have at least 1 meter space from combustible materials.

• Do not touch the unit with wet or damp hands or when barefoot.

• If the air conditioner is knocked over during use, turn off the unit and unplug it from the main power

supply immediately. Visually inspect the unit to ensure there is no damage. If you suspect the unit has

been damaged contact a technician or customer service for assistance.

• In a thunderstorm, the power must be cut off to avoid damage to the machine due to lightning.

• You air conditioner should be used in such a way that it is protected from moisture. e.g. condensation,

splashed water, etc. Do not place or store you air conditioner where it can fall or be pulled into water

or any other liquid. Unplug immediately if this occurs.

• All wiring must be performed strictly in accordance with the wiring diagram location inside the unit.

• The units circuit board (PCB) is designed with a fuse to provide over current protection. The

speciﬁ cations of the fuse are printed on the circuit board.

• When the water drainage function is not in use keep the upper and lower drain plugs ﬁ rmly installed in

the unit. The drain plugs can be a choking hazard to children.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

CAUTION

• This appliance is not intended for use by persons (including children) whose physical, sensory or

mental capabilities may be different or reduced, or who lack experience or knowledge, unless such

persons receive supervision or training to operate the appliance by a person responsible for their

safety. Children should be supervised to ensure that they do not play with the appliance. Children must

be supervised around the unit at all times.

• If the power supply cord is damaged it must be replaced by the manufacturer, its service agent or

similarly qualiﬁ ed persons in order to avoid a hazard.

• Prior to cleaning or other maintenance, the appliance must be disconnected from the power supply.

• Do not remove any ﬁ xed covers. Never use this appliance if it is not working properly or if it has been

dropped or damaged.

• Do not run cord under carpeting. Do not cover cord with throw rugs, runners or similar coverings. Do

not route cord under furniture or appliances. Arrange cords away from trafﬁ c and where it will not be

tripped over.

• Do not operate a unit with a damaged power cord, plug, power fuse or circuit breaker. Discard the unit

or return to an authorized service facility for examination and/or repair.

• To reduce the risk of ﬁ re or electric shock do not use this air conditioner with any solid-state speed

control device.

• The appliance shall be installed in accordance with national wiring regulations.

• Contact the authorized service technician for repair or maintenance of this unit.

• Contact the authorized service installer for installation of this unit.

• Do not cover or obstruct the inlet or outlet grilles.

• Do not use this product for functions other than those described in this instruction manual.

• Before cleaning turn off the power and unplug the unit.

• Disconnect the power if strange sounds, smells or smoke comes from it.

• Do not press the buttons on the control panel with anything other than your ﬁ ngers.

• Do not remove any ﬁ xed covers. Never use this appliance if it is not working properly or if it has been

dropped or damaged.

• Do not operate or stop the unit by inserting or pulling out the power cord plug.

• Do not use hazardous chemicals to clean or come into contact with the unit. Do not use the unit in the

presence of inﬂ ammable substances or vapour such as alcohol, insecticides, petrol, etc.

• Always transport your air conditioner in a vertical position and stand on a stable, level surface during

use.

• Always contact a qualiﬁ ed person to carry out repairs. If the damaged power supply cord must be

replaced with a new power supply cord obtained from the product manufacturer and not repaired.

• Hold the plug by the head of the power plug when removing it.

• Turn off the appliance when not in use.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

Note about ﬂ uorinated gasses

• Fluorinated greenhouse gases are contained in hermetically sealed equipment. For speciﬁ c information

on the type, the amount and the C02 equivalent in tonnes of the ﬂ uorinated greenhouse gas on some

models. Please refer to the relevant label on the unit itself.

• Installation, service, maintenance and repair of this unit must be performed by a certiﬁ ed technician.

• Product installation and recycling must be performed by a certiﬁ ed technician.

WARNING for using R32 refrigerant

• Do not use means to accelerate the defrosting process or to clean other than those recommended by the

manufacturer.

• The appliance shall be stored in a room without continuously operating ignition sources for example,

open ﬂ ames, an operating gas appliance or an operating electric heater.

• Do not pierce or burn.

• Be aware that the refrigerants may not contain an odour.

• The appliance should be installed, operated and stored in a room with a ﬂ oor area according to the

amount of refrigerant to be charged. For speciﬁ c information on the type of gas and the amount,

please refer to the relevant label on the unit itself. When there are differences between the label and the

manual on the minimum room area description, the description on the label shall prevail.

• Compliance with national gas regulations shall be observed.

• Keep ventilation openings clear of obstruction.

• The appliance shall be stored so as to prevent mechanical damage from occurring.

• A warning that the appliance shall be stored in a well-ventilated area where the room size corresponds

to the room area as speciﬁ ed for operation.

• Any person involved with working on the refrigerant circuit should hold a current, valid certiﬁ cate from

an industry accredited assessment authority which authorizes their competence to handle refrigerants

safely in accordance with an industry recognized assessment speciﬁ cation.

• Servicing shall only be performed as recommended by the manufacturer. Maintenance and repair

requiring the assistance of other skilled personnel shall be carried out under the supervision of the

person competent in the use of ﬂ ammable refrigerants.

• Please follow the instruction carefully to handle, install, clear and service the air conditioner to

avoid any damage or hazard. Flammable refrigerant R32 is used within this air conditioner. When

maintaining or disposing of the air conditioner the refrigerant must be recovered properly and should

not be allowed to discharge to the air directly.

• No open ﬁ re or device like switch which may generate spark/arcing shall be around air conditioner to

avoid causing ignition of the ﬂ ammable refrigerant used.

• Please follow the instruction carefully to store or maintain the air conditioner to prevent mechanical

damage from occurring.

• Flammable refrigerant -R32 is used in air conditioner. Please follow the instruction carefully to avoid

any hazard. For speciﬁ c information on the type of gas and the amount, please to the relevant label on

the unit itself.

• The appliance shall be stored in a room without continuously operating open ﬂ ames (for example an

operating gas appliance) and ignition sources (for example an operating electric heater).

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

Transport of equipment containing ﬂ ammable refrigerants

See transport regulations.

Marking of equipment using signs

See local regulations.

Disposal of equipment using ﬂ ammable refrigerants

See national regulations.

Storage of equipment / appliances

The storage of equipment should be in accordance with the manufacturer’s instructions.

Storage of packed (unsold) equipment

Storage package protection should be constructed such that the mechanical damage to the equipment

inside the package will not cause a leak of the refrigerant charge. The maximum number of pieces of

equipment permitted to be stored together will be determined by local regulations.

Information on servicing

1. Checks to the area: Prior to beginning work on systems containing ﬂ ammable refrigerants, safety

checks are necessary to ensure that the risk of ignition is minimized. For repair to the refrigerating

system, the following precautions shall be complied with prior to conducting work on the system.

2. Work procedure: Work shall be undertaken under a controlled procedure so as to minimize the risk of

a ﬂ ammable gas or vapour being present while the work is being performed.

3. General work area: All maintenance staff and others working in the local area shall be instructed on

the nature of work being carried out. Work in conﬁ ned spaces shall be avoided. The area around the

work space shall be sectioned off. Ensure that the conditions within the work area have been made safe

by removing all ﬂ ammable material.

4. Checking for the presence of refrigerant: The area shall be checked with an appropriate refrigerant

detector prior to and during work to ensure the technician is aware of potentially ﬂ ammable

atmospheres. Ensure that the leak detection equipment being used is suitable for use with ﬂ ammable

refrigerants, i.e. non-sparking, adequately sealed and intrinsically safe.

5. Presence of ﬁ re extinguisher: If any hot work is to be conducted on the refrigeration equipment or

any associated parts, appropriate ﬁ re extinguishing equipment shall be available to hand. Have a dry

powder or C0

2

ﬁ re extinguisher adjacent to the work area.

SAVE THESE INSTRUCTIONS!

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

6. No ignition sources: No person carrying out work in relation to a refrigeration system which involves

exposing any pipe work that contains or has contained ﬂ ammable refrigerant shall use any sources

of ignition in such a manner that it may lead to risk of ﬁ re or explosion. All possible ignition sources

including cigarette smoking, should be kept sufﬁ ciently far away from the site of installation, repairing,

removing and disposal during which ﬂ ammable refrigerant can possibly be released to the surrounding

space. Prior to work taking place, the area around the equipment is to be surveyed to make sure there

are no ﬂ ammable hazards or ignition risks. No smoking signs shall be displayed.

7. Ventilated area: Ensure that the area is in the open or that it is adequately ventilated before breaking

into the system or conducting any hot work. A degree of ventilation shall continue during the period

that the work is carried out. The ventilation should safely disperse any released refrigerant and

preferable expel it externally into the atmosphere.

8. Checks to the refrigeration equipment: Where electrical components are being changed, they shall

be ﬁ t for the purpose and to the correct speciﬁ cation. At all times the manufacturer’s maintenance and

service guidelines shall be followed. If in doubt consult the manufacturer’s technical department for

assistance.

The following checks shall be applied to installations using ﬂ ammable refrigerants:

• The charge size is in accordance with the room size within which the refrigerant containing parts are

installed.

• The ventilation machinery and outlets are operating adequately and are not obstructed.

• If an indirect refrigerating circuit is being used, the secondary circuit shall be checked for the presence

of refrigerant.

• Marking to the equipment continues to be visible and legible. Markings and signs that become illegible

must be corrected.

• Refrigeration pipe or components are installed in a position where they are unlikely to be exposed

to any substance which may corrode refrigerant containing components, unless the components are

constructed of materials which are inherently resistant to being corroded or are suitable protected

against being corroded.

9. Checks to electrical devices: Repair and maintenance to electrical components shall include initial

safety checks and component inspection procedures. If a fault exists that could compromise safety, then

no electrical supply shall be connected to the circuit until it is satisfactorily dealt with. If the fault cannot

be corrected immediately but it is necessary to continue operation, an adequate temporary solution

shall be used. This shall be reported to the owner of the equipment so all parties are advised.

Initial safety checks shall include:

• That capacitors are discharged. This shall be done in a safe manner to avoid possibility of sparking.

• That no live electrical components and wiring are exposed while charging, recovering or purging the

system.

• That there is continuity of earth bonding.

SAVE THESE INSTRUCTIONS!

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Repairs to sealed components

1. During repairs to sealed components, all electrical supplies shall be disconnected from the equipment

being worked upon prior to any removal of sealed covers, etc. If it is absolutely necessary to have an

electrical supply to equipment during servicing then a permanently operating form of leak detection

shall be located at the most critical point to warn of a potentially hazardous situation.

2. To ensure that by working on electrical components the casing is not altered in such a way that the level

of protection is affected, particular attention shall be paid to the following:

• Damage to cables, excessive number of connections, terminals not made to original speciﬁ cation,

damage to seals, incorrect ﬁ tting of glands, etc.

• Ensure the apparatus is mounted securely.

• Ensure that seals or sealing materials have not degraded such that they no longer serve the purpose of

preventing the ingress of ﬂ ammable atmospheres. Replacement parts shall be in accordance with the

manufacturer’s speciﬁ cations.

Note: The use of silicon sealant may inhibit the effectiveness of some types of leak detection equipment.

Intrinsically safe components do not have to be isolated prior to working on them.

Repair to intrinsically safe components

Do not apply any permanent inductive or capacitance loads to the circuit without ensuring that this

will not exceed the permissible voltage and current permitted for the equipment in use. Intrinsically

safe components are the only types that can be worked on while live in the presence of a ﬂ ammable

atmosphere. The test apparatus shall be at the correct rating. Replace components only with parts speciﬁ ed

by the manufacturer. Other parts may result in the ignition of refrigerant in the atmosphere from a leak.

Cabling

Check that cabling will not be subject to wear, corrosion, excessive pressure, vibration, sharp edges or any

other adverse environmental effects. The check shall also take into account the effects of aging or continual

vibration from sources such as compressors or fans.

Detection of ﬂ ammable refrigerants

Under no circumstances shall potential sources of ignition be used in the searching for or detection of

refrigerant leaks. A halide torch or any other detector using a naked ﬂ ame shall not be used.

SAVE THESE INSTRUCTIONS!

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Leak detection methods

The following leak detection methods are deemed acceptable for systems containing ﬂ ammable

refrigerants:

• Electronic leak detectors shall be used to detect ﬂ ammable refrigerants but the sensitivity may not be

adequate or may need recalibration. Detection equipment shall be calibrated in a refrigerant-free area.

Ensure that the detector is not a potential source of ignition and is suitable for the refrigerant used.

• Leak detection equipment shall be set at a percentage of the LFL of the refrigerant and shall be

calibrated to the refrigerant employed and the appropriate percentage of gas (25% maximum) is

conﬁ rmed.

• Leak detection ﬂ uids are suitable for use with most refrigerants but the use of detergents containing

chlorine shall be avoided as the chlorine may react with the refrigerant and corrode the copper or

pipe-work.

• If a leak is suspected, all naked ﬂ ames shall be removed or extinguished.

• If a leakage of refrigerant is found which requires brazing, all of the refrigerant shall be recovered

from the system or isolated by means of shut off valves in a part of the system remote from the leak.

Oxygen free nitrogen (OFN) shall then be purged through the system both before and during the

brazing process.

Removal and evacuation

When breaking into the refrigerant circuit to make repairs or for any other purpose conventional

procedures shall be used. However, it is important that the best practice is followed since ﬂ ammability is a

consideration. The following procedures shall be adhered to:

• Remove refrigerant.

• Purge the circuit with inert gas.

• Evacuate.

• Purge again with inert gas.

• Open the circuit by cutting or brazing.

• The refrigerant charge shall be recovered into the correct recovery cylinders. The system shall be

ﬂ ushed with OFN to render the unit safe. This process may need to be repeated several times.

Compressed air or oxygen shall not be used for this task.

• Flushing shall be achieved by breaking the vacuum in the system with OFN and continuing to ﬁ ll until

the working pressure is achieved, then venting to atmosphere and ﬁ nally pulling down to a vacuum.

This process shall be repeated until no refrigerant is within the system. When the ﬁ nal OFN charge

is used, the system shall be vented down to atmospheric pressure to enable work to take place. This

operation is absolutely vital is brazing operations on the pipe-work are to take place.

• Ensure that the outlet for the vacuum pump is not close to any ignition sources and there is ventilation

available.

SAVE THESE INSTRUCTIONS!

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Charging procedures

In addition to conventional charging procedures, the following requirements shall be followed:

• Ensure that contamination of different refrigerants does not occur when using charging equipment.

Hoses or lines shall be as short as possible to minimize the amount of refrigerant contained in them.

• Cylinders shall be kept upright.

• Ensure that the refrigeration system is earthed prior to charging the system with refrigerant.

• Label the system when charging is complete, if not already labeled.

• Extreme care shall be taken not to overﬁ ll the refrigeration system.

• Prior to recharging the system it shall be pressure tested with OFN. The system shall be leak tested on

completion of charging but prior to commissioning. A follow up leak test shall be carried out prior to

leaving the site.

Decommissioning

Before carrying out this procedure, it is essential that the technician is completely familiar with the

equipment in all its detail. It is recommended good practice that all refrigerants are recovered safely. Prior

to the task being carried out, an oil and refrigerant sample shall be taken in case analysis is required

prior to re-use of reclaimed refrigerant. It is essential that electrical power is available before the task is

commenced.

A. Become familiar with the equipment and its operation.

B. Isolate system electrically.

C. Before attempting the procedure ensure that:

• Mechanical handling equipment is available if required for handling refrigerant cylinders.

• All personal protective equipment is available and being used correctly.

• The recovery process is supervised at all times by a competent person.

• Recovery equipment and cylinders conform to the appropriate standards.

D. Pump down refrigerant system, if possible.

E. If a vacuum is not possible, make a manifold so that refrigerant can be removed from various parts of

the system.

F. Make sure that cylinder is situated on the scales before recovery takes place.

G. Start the recovery machine and operate in accordance with the manufacturer’s instructions.

H. Do not overﬁ ll cylinders. No more than 80% volume liquid charge.

I. Do not exceed the maximum working pressure of the cylinder, even temporarily.

J. When the cylinders have been ﬁ lled correctly and the process is completed, make sure that the cylinders

and the equipment are removed from the site promptly and all isolation valves on the equipment are

closed off.

K. Recovered refrigerant shall not be charged into another refrigeration system unless it has been cleaned

and checked.

SAVE THESE INSTRUCTIONS!

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Labeling

Equipment shall be labeled stating that it has been decommissioned and emptied of refrigerant. The label

shall be dated and signed. Ensure that there are labels on the equipment stating the equipment contains

ﬂ ammable refrigerant.

Recovery

When removing refrigerant from a system, either for servicing or decommissioning, it is recommended

good practice that all refrigerants are removed safely.

When transferring refrigerant into cylinders, ensure that only appropriate refrigerant recovers cylinders are

employed. Ensure that the correct number of cylinders for holding the total system charge are available.

All cylinders to be used are designed for the recovered refrigerant and labeled for that refrigerant, i.e.

special cylinders for the recovery of refrigerant. Cylinders shall be complete with pressure relief valve and

associated shut-off valves in good working order. Empty recovery cylinders are evacuated and, if possible,

cooled before recovery occurs.

The recovery equipment shall be in good working order with a set of instructions concerning the equipment

that is at hand and shall be suitable for the recovery of ﬂ ammable refrigerants. In addition, a set of

calibrated weighing scales shall be available and in good working order. Hoses shall be complete with

leak-free disconnect couplings and in good condition. Before using the recovery machine, check that is it

in satisfactory working order, has been properly maintained and that any associated electrical components

are sealed to prevent ignition in the event of a refrigerant leak. Consult the manufacturer if in doubt.

The recovered refrigerant shall be returned to the refrigerant supplier in the correct recovery cylinder

and the relevant waste transfer note shall be arranged. Do not mix refrigerants in recovery units and

especially not in cylinders. If compressors or compressor oils are to be removed, ensure that they have

been evacuated to an acceptable level to make certain that ﬂ ammable refrigerant does not remain within

the lubricant. The evacuation process shall be carried out prior to returning the compressor to the suppliers.

Only electric heating to the compressor body shall be employed to accelerate this process. When oil is

drained form a system, it shall be carried out safely.

12

INSTALLATION INSTRUCTIONS

LOCATION

This air conditioner is designed to ﬁ t inside a

standard double-hung window width opening

widths of 22 - 36” (55.9 - 91.4 cm).

The lower sash must open sufﬁ ciently to allow a

clear vertical opening of 35 cm (13.75”).

This air conditioner is not designed for vertical,

slider type windows or “through the wall”

installation.

Ensure that the window and frame are structurally

sound and free from dry or rotted wood.

Install the air conditioner on a side of the building

which favors more shade than sunlight. If the

appliance must be in direct sunlight, it is advisable

to provide a shade awning to ensure efﬁ cient

functioning.

Do not install the appliance where leakage of

combustible gas is suspected.

This air conditioner is designed to evaporate

condensation under normal conditions. Under

extremely hot or humid conditions, excess

condensation may overﬂ ow to the outside. The air

conditioner should be installed where condensation

cannot drip on pedestrians or neighboring

properties.

Provide sufﬁ cient clearance around the appliance

to allow ample air circulation. The rear of the

appliance should be outdoors, it should not be in a

garage or another room. Keep the appliance away

from obstacles and at least 30” above the ground.

Ensure that curtains and other obstructions do not

block air ﬂ ow.

13.75" min

22" to 36"

(55.9 cm to 91.4 cm)

(35 cm)

A

B

C

D

E

A. Interior wall

B. Exterior wall

C. Inner window sill

D. Offset

E. Seal foam

Wooden Windows

Vinyl-Clad Windows

13.75" min

22" to 36"

(55.9 cm to 91.4 cm)

(35 cm)

A

B

C

D

E

* Denotes extra hardware provided in separate bag.

INSTALLATION INSTRUCTIONS

SUPPORT BRACKET DETAILS

1. Rear cross brace

2. Main support

3. Left extension arm

4. Angled support arms

5. Horizontal bracket

6. Spring push pin

7. Right extension arm

REQUIRED TOOLS

• Phillips screwdriver

• Flat head screwdriver

• Pencil

• Measuring Tape

• Carpenter’s Level

• Drill and 1/8” drill bit

Note: Save the shipping carton and packing

materials for future storage or transportation. Please

check the contents of the accessory bags against the

below check list prior to installation.

INCLUDED ACCESSORIES

1/2” type B screw (x2) *

1/4” type B screw (x2) *

1” type A screw (x2) *

1/2” type A screw (x3) *

Support bracket

Right extension arm

Right extension arm (short)

Main support pin (x2) *

Cotter pin (x2) *

Right open window bracket

Left open window bracket

Side arm foam (x2)

Window sash lock

Window sash foam

Window sealing foam

Bracket sealing foam

Additional side arm foam

1

2

3

4

5

6

7

PREPARE THE SUPPORT BRACKET

1. Find the center of the window sill and lightly

mark it with a pencil.

2. Measure the width of the window.

3. Adjust the left extension arm, then install and

adjust the right extension arm to the correct

width by pressing the spring push pins. Note

that the bracket may be slightly offset to the left

of center when placed in the window.

4. Apply the bracket sealing foam to the bottom of

the left and right extension arms.

Important:

• Windows with widths between 26 - 36” should

use the right extension arm.

• Windows with widths between 26 - 26” should

used the short right extension arm

INSTALL THE SUPPORT BRACKET

Install the support bracket into the window opening. Ensure that the horizontal bracket and extension arms

are located on the indoor side of the window.

INSTALLATION INSTRUCTIONS

14

Wooden Window Sill Vinyl-Clad Window Sill

For wooden window sills or ﬂ at window sills, secure

the bracket to the window sill by drilling 1/8” pilot

holes and installing the 1/2” and 1” type A screws

as shown.

For vinyl-clad window sills, secure the bracket to

the window sill by drilling 1/8” pilot holes and

installing the 1/2” type A screws as shown.

1” Type A

1/2” Typ e A 1/2” Type A

1/2” Type A

INSTALLATION INSTRUCTIONS

Angled Support Arms

Move the angled support arms toward the exterior

wall until the feet touch the wall.

Place the level on the support bracket and adjust

the support arms so that it is tilted 1/4 bubble

downward toward the outside. The level bubble

should appear as shown.

15

Insert the main support pin through the holes in

the support bracket and angled support arms.

Ensure that the pins on both sides are in the same

numbered hole.

If further adjustment is needed, use alternate holes

where the main supports attach to the horizontal

bracket.

Check the level again and ensure the bracket feels

secure. After making any necessary adjustments,

insert the cotter pins into the main support pins.

If necessary, cover the holes in the front of the

bracket with the bracket sealing foam.

16

INSTALLATION INSTRUCTIONS

INSTALL THE AIR CONDITIONER

Set the air conditioner on top of the support

bracket. Ensure the grooves on the bottom of the air

conditioner align with the support bracket. Using a

level, check for the proper tilt toward the outside.

Pull the window down into the slot in the air

conditioner to hold it steady but do not close it all

the way yet.

Fold down both side arm hinges.

Install the open window brackets using the provided

screws as shown.

Warning: Failing to install the open window

brackets could cause injury or property damage.

1/2” type B

1/4” type B

INSTALLATION INSTRUCTIONS

FOAM INSTALLATION

Measure the distance between the side arm hinge and the closest part of the window frame in side with the

side arm. Add 1/4” to this distance and cut the side arm foam to the correct length.

Wooden Window Sill Vinyl-Clad Window Sill

Apply the window sealing foam to the side arm foam as shown. Note that the window sealing foam

attaches to the side next to the air conditioner.

A

B

C

D

A

B

D

17

Insert side arm foam into the side arm hinge until the top front of the side arm is ﬂ ush with the top of the

hinge. Complete the side foam installation on both sides of the unit.

A. Air conditioner side

B. Side arm foam

C. Additional side arm foam

D. Window sealing foam

INSTALLATION INSTRUCTIONS

18

ANTI TIP BRACKET

The anti tip brackets must be extended into the

window track opening until. Remove the screw from

the anti tip bracket, extend it as far as it will go to

the side of the window and then secure it with the

same screw.

Warning: The anti tip brackets must be extended

into the window track opening. Failure to use

the anti tip brackets can cause serious injury or

damage.

See below for an example of what the anti tip

bracket should look like when properly installed.

Note that the side arm foam has been removed

from this images for illustration purposes.

WINDOW SEALING FOAM

Install a strip of window sealing foam to the bottom

of the lower sash to seal any small gaps between

the window and the air conditioner. Make sure the

window is completely closed and then check for

gaps. Fill any gaps with the remaining foam as

needed.

Extend the integrated window locks, located in the

U-channel, until they contact the window.

Cut the window sash foam and insert it into the

space between the upper and lower sashes.

SASH LOCK

For added security, install the optional sash lock.

Secure the sash lock in place using 1/2” type A

screws as shown.

OPERATING INSTRUCTIONS

3s

CONTROL PANEL

1. WIRELESS CONNECT: Press to activate the wireless connection feature.

2. TIMER: Press to activate the timer feature.

3. ECO: Press to activate the ECO feature.

4. MODE: Press to set the desired mode.

5. TEMPERATURE CONTROL BUTTONS: Press to change the temperature setting. Press and hold the

temperature control buttons at the same time for 3 seconds to change the temperature scale being

displayed. The temperature can be set between 16 - 30°C (60 - 86°F).

6. FAN: Press to set the desired fan speed.

7. SLEEP: Press to activate the sleep feature.

8. SWING: Press to initiate the auto swing feature. Press again when the louver reaches the desired angle.

Press and hold the swing button for 3 seconds to reset the ﬁ lter after cleaning.

9. ON/OFF: Press to turn the appliance on or off.

19

MODE

Press the mode button to choose the desired mode.

Auto

Auto mode will automatically set cooling or fan only

operation based on the current temperature in the

room. Fan speed cannot be adjusted in this mode.

Cool

Choose cool mode to set the cooling function.

Use the temperature control buttons to choose the

desired temperature. The fan speed can be adjusted

by pressing the fan button.

Dry

Choose dry mode to set the dehumidifying function.

Condensed water will drain out the back of the unit.

Fan speed cannot be adjusted in this mode.

Fan

Fan mode will run the internal fan without engaging

the cooling function. The fan speed can be adjusted

by pressing the fan button.

La page charge ...

Danby DAC080B6IWDB-6 Le manuel du propriétaire

Ce manuel convient également à

Danby DAC080B6IWDB-6 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents