Danby DAC120B6WDB-6 Air Conditioner Le manuel du propriétaire

Marque: Danby

Modèle: DAC120B6WDB-6 Air Conditioner

Taper: Le manuel du propriétaire

Printed in China

Imprimé en Chine

Impreso en China

*Trademark of Danby Products

* Marque de commerce de Danby Products

* Marca comerciales de Danby Products

Danby Products Limited, Guelph, Ontario, Canada N1H 6Z9

Danby Products Inc. Findlay, Ohio, U.S.A. 45840

www.Danby.com

2022.12.20

MODEL • MODÈLE • MODELO

DAC100B6WDB

DAC120B6WDB-6

AIR CONDITIONER

Owner’s Manual.............................1 - 18

CLIMATISEUR

Manual du propriétaire.................19 - 36

AIRE ACONDICIONADO

Manual del propietario..................37 - 54

Welcome to the Danby family.

We are proud of our quality products and we believe in dependable service. We suggest

that you read this owner’s manual before plugging in your new appliance as it contains

important operation information, safety information, troubleshooting, and maintenance tips

to ensure the reliability and longevity of your appliance.

You are entitled to the warranty coverage as described in the owner’s manual provided with

your new appliance.

1. Please write down your appliance information below. You must keep the original proof

of purchase receipt to validate and receive warranty services.

2. Register your product online and receive a FREE 2 MONTH WARRANTY EXTENSION

after ﬁ lling out a product survey, at www.danby.com/support/product-registration/

Need Help?

1. Read your Owner’s Manual for installation help, troubleshooting, and maintenance

assistance.

2. Visit www.Danby.com to access self-service tools, FAQs and much more by searching

your model number in the search bar.

3. For the Quickest Customer Service, please ﬁ ll out the web form at www.danby.com/

support. Your submission will go directly to an expert on your particular appliance.

Our average response times are between 20 minutes and 2 hours, during EST business

hours.

4. Call 1-800-263-2629 - please note that during peak hours, hold times can exceed one

hour.

Model Number: ____________________________________________________

Serial Number: ____________________________________________________

Date of Purchase: __________________________________________________

SAVE THESE INSTRUCTIONS!

CAUTION: RISK OF FIRE

Flammable refrigerant used. When maintaining

or disposing of the air conditioner, the refrigerant

must not be allowed to vent into the open air.

WARNING Shows that the appliance uses a ﬂ ammable refrigerant. If the

refrigerant leaks and is exposed to an external ignition source, there is

a risk of ﬁ re.

CAUTION Shows that the operation manual should be read carefully.

CAUTION Shows that service personnel should be handling this equipment with

reference to the installation manual.

CAUTION Shows that the information is available such as the operating manual

or the installation manual.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAFETY PRECAUTIONS

WARNING

• Installation must be performed according to the installation instructions. Improper installation can cause

water leakage, electrical shock or ﬁ re.

• Use only the included accessories and parts and speciﬁ ed tools for the installation. Using non-standard

parts can cause water leakage, electrical shock, ﬁ re and injury or property damage.

• Make sure that the outlet you are using is grounded and has the appropriate voltage. The power cord

is equipped with a three-prong grounding plug to protect against shock. Voltage information can be

found on the nameplate of the unit.

• Your unit must be used in a properly grounded wall receptacle. If the wall receptacle you intend to

use is not adequately grounded or protected by a time delay fuse or circuit breaker (the fuse of circuit

breaker needed is determined by the maximum current of the unit. The maximum current is indicated

on the nameplate located on the unit), have a qualiﬁ ed electrician install the proper receptacle.

• Install the unit on a ﬂ at, sturdy surface. Failure to do so could result in damage or excessive noise and

vibration.

• The unit must be kept free from obstruction to ensure proper function and to mitigate safety hazards.

• Do not modify the length of the power cord or use an extension cord to power the unit.

• Do not share a single outlet with other electrical appliances. Improper power supply can cause ﬁ re or

electrical shock.

• Do not install your air conditioner in a wet room such as a bathroom or laundry room. Too much

exposure to water can cause electrical components to short circuit.

• Do not install the unit in a location that may be exposed to combustible gas as this could cause ﬁ re.

• The unit has wheels to facilitate moving. Make sure not to use the wheels on thick carpet or to roll over

objects as this could cause tipping.

• Do not operate a unit that been dropped or damaged.

• The appliance with the electric heater shall have at least 1 meter space from combustible materials.

• Do not touch the unit with wet or damp hands or when barefoot.

• If the air conditioner is knocked over during use, turn off the unit and unplug it from the main power

supply immediately. Visually inspect the unit to ensure there is no damage. If you suspect the unit has

been damaged contact a technician or customer service for assistance.

• In a thunderstorm, the power must be cut off to avoid damage to the machine due to lightning.

• Your air conditioner should be used in such a way that it is protected from moisture. e.g. condensation,

splashed water, etc. Do not place or store you air conditioner where it can fall or be pulled into water

or any other liquid. Unplug immediately if this occurs.

• All wiring must be performed strictly in accordance with the wiring diagram location inside the unit.

• The units circuit board (PCB) is designed with a fuse to provide over current protection. The

speciﬁ cations of the fuse are printed on the circuit board.

• When the water drainage function is not in use keep the upper and lower drain plugs ﬁ rmly installed in

the unit. The drain plugs can be a choking hazard to children.

SAVE THESE INSTRUCTIONS!

CAUTION

• This appliance is not intended for use by persons (including children) whose physical, sensory or

mental capabilities may be different or reduced, or who lack experience or knowledge, unless such

persons receive supervision or training to operate the appliance by a person responsible for their

safety. Children should be supervised to ensure that they do not play with the appliance. Children must

be supervised around the unit at all times.

• If the power supply cord is damaged it must be replaced by the manufacturer, its service agent or

similarly qualiﬁ ed persons in order to avoid a hazard.

• Prior to cleaning or other maintenance, the appliance must be disconnected from the power supply.

• Do not remove any ﬁ xed covers. Never use this appliance if it is not working properly or if it has been

dropped or damaged.

• Do not run cord under carpeting. Do not cover cord with throw rugs, runners or similar coverings. Do

not route cord under furniture or appliances. Arrange cords away from trafﬁ c and where it will not be

tripped over.

• Do not operate a unit with a damaged power cord, plug, power fuse or circuit breaker. Discard the unit

or return to an authorized service facility for examination and/or repair.

• To reduce the risk of ﬁ re or electric shock do not use this air conditioner with any solid-state speed

control device.

• The appliance shall be installed in accordance with national wiring regulations.

• Contact the authorized service technician for repair or maintenance of this unit.

• Contact the authorized service installer for installation of this unit.

• Do not cover or obstruct the inlet or outlet grilles.

• Do not use this product for functions other than those described in this instruction manual.

• Before cleaning turn off the power and unplug the unit.

• Disconnect the power if strange sounds, smells or smoke comes from it.

• Do not press the buttons on the control panel with anything other than your ﬁ ngers.

• Do not remove any ﬁ xed covers. Never use this appliance if it is not working properly or if it has been

dropped or damaged.

• Do not operate or stop the unit by inserting or pulling out the power cord plug.

• Do not use hazardous chemicals to clean or come into contact with the unit. Do not use the unit in the

presence of inﬂ ammable substances or vapour such as alcohol, insecticides, petrol, etc.

• Always transport your air conditioner in a vertical position and stand on a stable, level surface during

use.

• Always contact a qualiﬁ ed person to carry out repairs. If the damaged power supply cord must be

replaced with a new power supply cord obtained from the product manufacturer and not repaired.

• Hold the plug by the head of the power plug when removing it.

• Turn off the appliance when not in use.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

Note about ﬂ uorinated gasses

• Fluorinated greenhouse gases are contained in hermetically sealed equipment. For speciﬁ c information

on the type, the amount and the C02 equivalent in tonnes of the ﬂ uorinated greenhouse gas on some

models. Please refer to the relevant label on the unit itself.

• Installation, service, maintenance and repair of this unit must be performed by a certiﬁ ed technician.

• Product installation and recycling must be performed by a certiﬁ ed technician.

WARNING for using R32 refrigerant

• Do not use means to accelerate the defrosting process or to clean other than those recommended by the

manufacturer.

• The appliance shall be stored in a room without continuously operating ignition sources for example,

open ﬂ ames, an operating gas appliance or an operating electric heater.

• Do not pierce or burn.

• Be aware that the refrigerants may not contain an odor.

• The appliance should be installed, operated and stored in a room with a ﬂ oor area according to the

amount of refrigerant to be charged. For speciﬁ c information on the type of gas and the amount,

please refer to the relevant label on the unit itself. When there are differences between the label and the

manual on the minimum room area description, the description on the label shall prevail.

• Compliance with national gas regulations shall be observed.

• Keep ventilation openings clear of obstruction.

• The appliance shall be stored so as to prevent mechanical damage from occurring.

• A warning that the appliance shall be stored in a well-ventilated area where the room size corresponds

to the room area as speciﬁ ed for operation.

• Any person involved with working on the refrigerant circuit should hold a current, valid certiﬁ cate from

an industry accredited assessment authority which authorizes their competence to handle refrigerants

safely in accordance with an industry recognized assessment speciﬁ cation.

• Servicing shall only be performed as recommended by the manufacturer. Maintenance and repair

requiring the assistance of other skilled personnel shall be carried out under the supervision of the

person competent in the use of ﬂ ammable refrigerants.

• Please follow the instruction carefully to handle, install, clear and service the air conditioner to

avoid any damage or hazard. Flammable refrigerant R32 is used within this air conditioner. When

maintaining or disposing of the air conditioner the refrigerant must be recovered properly and should

not be allowed to discharge to the air directly.

• No open ﬁ re or device like switch which may generate spark/arcing shall be around air conditioner to

avoid causing ignition of the ﬂ ammable refrigerant used.

• Please follow the instruction carefully to store or maintain the air conditioner to prevent mechanical

damage from occurring.

• Flammable refrigerant -R32 is used in air conditioner. Please follow the instruction carefully to avoid

any hazard. For speciﬁ c information on the type of gas and the amount, please to the relevant label on

the unit itself.

• The appliance shall be stored in a room without continuously operating open ﬂ ames (for example an

operating gas appliance) and ignition sources (for example an operating electric heater).

Transport of equipment containing ﬂ ammable refrigerants: See transport regulations.

Marking of equipment using signs: See local regulations.

Disposal of equipment using ﬂ ammable refrigerants: See national regulations.

Storage of equipment / appliances: The storage of equipment should be in accordance with the

manufacturer’s instructions.

Storage of packed (unsold) equipment: Storage package protection should be constructed such that the

mechanical damage to the equipment inside the package will not cause a leak of the refrigerant charge.

The maximum number of pieces of equipment permitted to be stored together will be determined by local

regulations.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

Information on servicing

1. Checks to the area: Prior to beginning work on systems containing ﬂ ammable refrigerants, safety

checks are necessary to ensure that the risk of ignition is minimized. For repair to the refrigerating

system, the following precautions shall be complied with prior to conducting work on the system.

2. Work procedure: Work shall be undertaken under a controlled procedure so as to minimize the risk of

a ﬂ ammable gas or vapour being present while the work is being performed.

3. General work area: All maintenance staff and others working in the local area shall be instructed on

the nature of work being carried out. Work in conﬁ ned spaces shall be avoided. The area around the

work space shall be sectioned off. Ensure that the conditions within the work area have been made safe

by removing all ﬂ ammable material.

4. Checking for the presence of refrigerant: The area shall be checked with an appropriate refrigerant

detector prior to and during work to ensure the technician is aware of potentially ﬂ ammable

atmospheres. Ensure that the leak detection equipment being used is suitable for use with ﬂ ammable

refrigerants, i.e. non-sparking, adequately sealed and intrinsically safe.

5. Presence of ﬁ re extinguisher: If any hot work is to be conducted on the refrigeration equipment or

any associated parts, appropriate ﬁ re extinguishing equipment shall be available to hand. Have a dry

powder or C02 ﬁ re extinguisher adjacent to the work area.

6. No ignition sources: No person carrying out work in relation to a refrigeration system which involves

exposing any pipe work that contains or has contained ﬂ ammable refrigerant shall use any sources

of ignition in such a manner that it may lead to risk of ﬁ re or explosion. All possible ignition sources

including cigarette smoking, should be kept sufﬁ ciently far away from the site of installation, repairing,

removing and disposal during which ﬂ ammable refrigerant can possibly be released to the surrounding

space. Prior to work taking place, the area around the equipment is to be surveyed to make sure there

are no ﬂ ammable hazards or ignition risks. No smoking signs shall be displayed.

7. Ventilated area: Ensure that the area is in the open or that it is adequately ventilated before breaking

into the system or conducting any hot work. A degree of ventilation shall continue during the period

that the work is carried out. The ventilation should safely disperse any released refrigerant and

preferable expel it externally into the atmosphere.

8. Checks to the refrigeration equipment: Where electrical components are being changed, they shall

be ﬁ t for the purpose and to the correct speciﬁ cation. At all times the manufacturer’s maintenance and

service guidelines shall be followed. If in doubt consult the manufacturer’s technical department for

assistance. The following checks shall be applied to installations using ﬂ ammable refrigerants:

• The charge size is in accordance with the room size within which the refrigerant containing parts

are installed.

• The ventilation machinery and outlets are operating adequately and are not obstructed.

• If an indirect refrigerating circuit is being used, the secondary circuit shall be checked for the

presence of refrigerant.

• Marking to the equipment continues to be visible and legible. Markings and signs that become

illegible must be corrected.

• Refrigeration pipe or components are installed in a position where they are unlikely to be exposed

to any substance which may corrode refrigerant containing components, unless the components are

constructed of materials which are inherently resistant to being corroded or are suitable protected

against being corroded.

9. Checks to electrical devices: Repair and maintenance to electrical components shall include initial

safety checks and component inspection procedures. If a fault exists that could compromise safety, then

no electrical supply shall be connected to the circuit until it is satisfactorily dealt with. If the fault cannot

be corrected immediately but it is necessary to continue operation, an adequate temporary solution

shall be used. This shall be reported to the owner of the equipment so all parties are advised. Initial

safety checks shall include:

• That capacitors are discharged. This shall be done in a safe manner to avoid possibility of sparking.

• That no live electrical components and wiring are exposed while charging, recovering or purging

the system.

• That there is continuity of earth bonding.

SAVE THESE INSTRUCTIONS!

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Repairs to sealed components

1. During repairs to sealed components, all electrical supplies shall be disconnected from the equipment

being worked upon prior to any removal of sealed covers, etc. If it is absolutely necessary to have an

electrical supply to equipment during servicing then a permanently operating form of leak detection

shall be located at the most critical point to warn of a potentially hazardous situation.

2. To ensure that by working on electrical components the casing is not altered in such a way that the level

of protection is affected, particular attention shall be paid to the following:

• Damage to cables, excessive number of connections, terminals not made to original speciﬁ cation,

damage to seals, incorrect ﬁ tting of glands, etc.

• Ensure the apparatus is mounted securely.

• Ensure that seals or sealing materials have not degraded such that they no longer serve the purpose of

preventing the ingress of ﬂ ammable atmospheres. Replacement parts shall be in accordance with the

manufacturer’s speciﬁ cations.

Note: The use of silicon sealant may inhibit the effectiveness of some types of leak detection equipment.

Intrinsically safe components do not have to be isolated prior to working on them.

Repair to intrinsically safe components

Do not apply any permanent inductive or capacitance loads to the circuit without ensuring that this

will not exceed the permissible voltage and current permitted for the equipment in use. Intrinsically

safe components are the only types that can be worked on while live in the presence of a ﬂ ammable

atmosphere. The test apparatus shall be at the correct rating. Replace components only with parts speciﬁ ed

by the manufacturer. Other parts may result in the ignition of refrigerant in the atmosphere from a leak.

Cabling

Check that cabling will not be subject to wear, corrosion, excessive pressure, vibration, sharp edges or any

other adverse environmental effects. The check shall also take into account the effects of aging or continual

vibration from sources such as compressors or fans.

Detection of ﬂ ammable refrigerants

Under no circumstances shall potential sources of ignition be used in the searching for or detection of

refrigerant leaks. A halide torch or any other detector using a naked ﬂ ame shall not be used.

Leak detection methods

The following leak detection methods are deemed acceptable for systems containing ﬂ ammable

refrigerants:

• Electronic leak detectors shall be used to detect ﬂ ammable refrigerants but the sensitivity may not be

adequate or may need recalibration. Detection equipment shall be calibrated in a refrigerant-free area.

Ensure that the detector is not a potential source of ignition and is suitable for the refrigerant used.

• Leak detection equipment shall be set at a percentage of the LFL of the refrigerant and shall be

calibrated to the refrigerant employed and the appropriate percentage of gas (25% maximum) is

conﬁ rmed.

• Leak detection ﬂ uids are suitable for use with most refrigerants but the use of detergents containing

chlorine shall be avoided as the chlorine may react with the refrigerant and corrode the copper or

pipe-work.

• If a leak is suspected, all naked ﬂ ames shall be removed or extinguished.

• If a leakage of refrigerant is found which requires brazing, all of the refrigerant shall be recovered

from the system or isolated by means of shut off valves in a part of the system remote from the leak.

Oxygen free nitrogen (OFN) shall then be purged through the system both before and during the

brazing process.

SAVE THESE INSTRUCTIONS!

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Removal and evacuation

When breaking into the refrigerant circuit to make repairs or for any other purpose conventional

procedures shall be used. However, it is important that the best practice is followed since ﬂ ammability is a

consideration. The following procedures shall be adhered to:

• Remove refrigerant.

• Purge the circuit with inert gas.

• Evacuate.

• Purge again with inert gas.

• Open the circuit by cutting or brazing.

• The refrigerant charge shall be recovered into the correct recovery cylinders. The system shall be

ﬂ ushed with OFN to render the unit safe. This process may need to be repeated several times.

Compressed air or oxygen shall not be used for this task.

• Flushing shall be achieved by breaking the vacuum in the system with OFN and continuing to ﬁ ll until

the working pressure is achieved, then venting to atmosphere and ﬁ nally pulling down to a vacuum.

This process shall be repeated until no refrigerant is within the system. When the ﬁ nal OFN charge

is used, the system shall be vented down to atmospheric pressure to enable work to take place. This

operation is absolutely vital is brazing operations on the pipe-work are to take place.

• Ensure that the outlet for the vacuum pump is not close to any ignition sources and there is ventilation

available.

Charging procedures

In addition to conventional charging procedures, the following requirements shall be followed:

• Ensure that contamination of different refrigerants does not occur when using charging equipment.

Hoses or lines shall be as short as possible to minimize the amount of refrigerant contained in them.

• Cylinders shall be kept upright.

• Ensure that the refrigeration system is earthed prior to charging the system with refrigerant.

• Label the system when charging is complete, if not already labeled.

• Extreme care shall be taken not to overﬁ ll the refrigeration system.

• Prior to recharging the system it shall be pressure tested with OFN. The system shall be leak tested on

completion of charging but prior to commissioning. A follow up leak test shall be carried out prior to

leaving the site.

Decommissioning

Before carrying out this procedure, it is essential that the technician is completely familiar with the

equipment in all its detail. It is recommended good practice that all refrigerants are recovered safely. Prior

to the task being carried out, an oil and refrigerant sample shall be taken in case analysis is required

prior to re-use of reclaimed refrigerant. It is essential that electrical power is available before the task is

commenced.

A. Become familiar with the equipment and its operation.

B. Isolate system electrically.

C. Before attempting the procedure ensure that:

• Mechanical handling equipment is available if required for handling refrigerant cylinders.

• All personal protective equipment is available and being used correctly.

• The recovery process is supervised at all times by a competent person.

• Recovery equipment and cylinders conform to the appropriate standards.

D. Pump down refrigerant system, if possible.

E. If a vacuum is not possible, make a manifold so that refrigerant can be removed from various parts of

the system.

F. Make sure that cylinder is situated on the scales before recovery takes place.

G. Start the recovery machine and operate in accordance with the manufacturer’s instructions.

H. Do not overﬁ ll cylinders. No more than 80% volume liquid charge.

I. Do not exceed the maximum working pressure of the cylinder, even temporarily.

J. When the cylinders have been ﬁ lled correctly and the process is completed, make sure that the cylinders

and the equipment are removed from the site promptly and all isolation valves on the equipment are

closed off.

K. Recovered refrigerant shall not be charged into another refrigeration system unless it has been cleaned

and checked.

SAVE THESE INSTRUCTIONS!

Labeling

Equipment shall be labeled stating that it has been decommissioned and emptied of refrigerant. The label

shall be dated and signed. Ensure that there are labels on the equipment stating the equipment contains

ﬂ ammable refrigerant.

Recovery

When removing refrigerant from a system, either for servicing or decommissioning, it is recommended

good practice that all refrigerants are removed safely.

When transferring refrigerant into cylinders, ensure that only appropriate refrigerant recovers cylinders are

employed. Ensure that the correct number of cylinders for holding the total system charge are available.

All cylinders to be used are designed for the recovered refrigerant and labeled for that refrigerant, i.e.

special cylinders for the recovery of refrigerant. Cylinders shall be complete with pressure relief valve and

associated shut-off valves in good working order. Empty recovery cylinders are evacuated and, if possible,

cooled before recovery occurs.

The recovery equipment shall be in good working order with a set of instructions concerning the equipment

that is at hand and shall be suitable for the recovery of ﬂ ammable refrigerants. In addition, a set of

calibrated weighing scales shall be available and in good working order. Hoses shall be complete with

leak-free disconnect couplings and in good condition. Before using the recovery machine, check that is it

in satisfactory working order, has been properly maintained and that any associated electrical components

are sealed to prevent ignition in the event of a refrigerant leak. Consult the manufacturer if in doubt.

The recovered refrigerant shall be returned to the refrigerant supplier in the correct recovery cylinder

and the relevant waste transfer note shall be arranged. Do not mix refrigerants in recovery units and

especially not in cylinders. If compressors or compressor oils are to be removed, ensure that they have

been evacuated to an acceptable level to make certain that ﬂ ammable refrigerant does not remain within

the lubricant. The evacuation process shall be carried out prior to returning the compressor to the suppliers.

Only electric heating to the compressor body shall be employed to accelerate this process. When oil is

drained form a system, it shall be carried out safely.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

INSTALLATION INSTRUCTIONS

LOCATION

• This air conditioner is designed for single or

double hung windows. Since window designs

vary, it may be necessary to make some

modiﬁ cations for safe installation. Ensure that

the window and frame are structurally sound

and free from dry or rotted wood.

• This air conditioner is not designed for vertical,

slider type windows or “through the wall”

installation.

• Install the air conditioner in a window on a

side of the building which favors more shade

than sunlight. If the appliance must be in direct

sunlight, it is advisable to provide a shade

awning over the appliance to ensure efﬁ cient

functioning.

• Do not install the appliance where leakage of

combustible gas is suspected.

• This appliance is designed to evaporate

condensation under normal conditions. Under

extremely hot or humid conditions, excess

condensation may overﬂ ow to the outside.

The appliance should be installed where

condensation cannot drip on pedestrians or

neighboring properties.

• Provide sufﬁ cient clearance around the

appliance to allow ample air circulation. The

rear of the appliance should be outdoors, it

should not be in a garage or another room.

Keep the appliance away from obstacles and

at least 76 cm (30 inches) above the ground.

Ensure that curtains and other obstructions do

not block air ﬂ ow to the appliance.

76.2 cm

(30 inches)

50.8 cm

(20 inches)

50.8 cm

(20 inches)

77.5 cm

(30.5 in)

REQUIRED TOOLS

• Screwdrivers: Phillips and ﬂ at head.

• Power Drill: 3.2mm (1/8”) diameter drill bit

• Pencil

• Measuring Tape

• Scissors

• Carpenter’s Level

ACCESSORIES

The following accessories are included with

the appliance and should be used during the

installation.

1. 13 mm (1/2 inch) screws (x7)

2. 9.5 mm (3/8 inch) screws (x4) (Factory installed

on some models.)

3. Safety Lock

4. Adhesive foam seal

5. Regular foam seal

6. “L” shaped mounting bracket (Factory installed

on some models.)

7. Bracket for wood windows (x2)

8. Bracket for vinyl windows (x2)

9. Weather stripping (x5)

10. Side curtains (x2)

12 3

INSTALLATION INSTRUCTIONS

L BRACKET

The “L” shaped bracket may come factory installed

on some models.

If the “L” shaped bracket is not pre-installed, attach

it to the top of the cabinet as shown below using the

provided 9.5 mm (3/8”) screws (x4).

INSTALLATION

Attach the side curtains to the appliance by sliding

the curtain frame into the side channel of the

cabinet. The curtains are labeled “left” and “right

on the frames. This refers to the left and right

sides of the appliance when facing the front of the

appliance.

Cut the regular foam seal to ﬁ t the area of the

window sill that the air conditioner will rest on.

Place the air conditioner into the window with the

“L” shaped mounting bracket positioned in front of

the upper sash. The bottom of the cabinet should be

positioned on the recessed portion of the window

frame. Pull the upper window sash down until it

rests just behind the front ﬂ ange of the “L” shaped

mounting bracket.

Expand the side curtains on each side and secure

the top of the frames to the window sash using one

13 mm (1/2”) screw on each side of the “L” shaped

mounting bracket.

Attach the clamps on the lower part of each curtain

to the window sill using one 13 mm (1/2”) screw on

each side of the cabinet.

Place the adhesive foam seal into the opening

between the inside and outside windows and

attached the safety lock to the outside window frame

using two 13 mm (1/2”) screws.

Check the Tilt Angle

The air conditioner should be tilted downward

towards the outside approximately 3° to 4°. This

tilt will encourage any condensed water to drain

to the outside. If any condensed water leaks to the

inside of the house, check the tilt angle and adjust

as necessary.

Measure the tilt angle from the front of the cabinet’s

edge. The difference in height between the front and

the back of the appliance, labeled “A” on the image

below, should be approximately 2.5 cm - 3.5 cm

(1” - 1 3/8”).

CONTROL PANEL

1. Display panel

• Displays the set temperature

• While in fan mode, shows the room

temperature

• Energy saver mode indicator

• Wireless connection indicator

• Cool mode indicator

• Fan mode indicator

• Temperature and timer display

• Temperature scale indicator

• Filter reset indicator

2. Mode button:

• Used to choose the operating mode.

• The ﬁ lter reset indicator will illuminate after

250 hours of use as a reminder to clean the

ﬁ lter. After cleaning the ﬁ lter, press and hold

the mode button for 3 seconds to clear the

ﬁ lter reset indicator.

3. Increase and decrease buttons:

• Used to adjust the set temperature.

• Press and hold the increase and decrease

buttons for 3 seconds to change between °C

and °F.

4. Power Button: Used to turn the appliance on or

off.

A. Energy saver mode indicator

B. Wireless connection indicator

C. Cool mode indicator

D. Fan mode indicator

E. Temperature display

F. Temperature scale indicator

G. Filter reset indicator

MODE

2 3 4

C E

FUNCTION INSTRUCTION

Operating Modes

• Cool Mode

Choose cool mode to set the cooling function. Use

the up and down arrows to choose the desired

temperature. When cool mode is selected, the fan

speed can be adjusted by pressing the fan button on

the remote control.

The temperature can be set within a range of 17°C -

30°C (62°F - 86°F).

• Fan Mode

Choose fan mode to run the internal fan without

engaging the cooling function. Press the fan button

on the remote control repeatedly to choose the fan

speed.

OPERATING INSTRUCTIONS

REMOTE CONTROL

1. Power Button: Used to turn the appliance on or

off.

2. Mode Button: Used to choose the operating

mode.

3. Fan Button: Used to set the fan speed.

4. Sleep Button: Used to set the sleep function.

5. Swing button: Used to set the angle of the louver

on the top of the appliance.

• Press once to begin the swing function.

• Press a second time to stop the louver when it

has reached the desired angle.

6. Energy Saver Button: Used to set the energy

saver function.

7. LED Button:

• Press to turn the LED back light on or off.

• Press 7 times to activate the wireless

connection. Follow the directions on

the wireless connection app for more

information.

8. Timer off button: Press to set the automatic off

timer.

9. Timer on button: Press to set the automatic on

timer.

10. Shor tcut button: Press to set and activate the

short cut function.

11. Increase and decrease buttons:

• Used to adjust the set temperature.

• Press and hold the increase and decrease

buttons for 3 seconds to change between °C

and °F.

12. LED display: Shows the set temperature and

timer setting.

4 5 6 7

REMOTE CONTROL BATTERIES

The remote control requires two AAA alkaline

batteries (included). Batteries should be replaced

when:

a) No sound is heard when attempting to program

the appliance.

b) The appliance does not respond to a command

issued by the remote control.

Battery replacement:

1. Slide the rear cover on the remote in the

direction of the arrow.

2. Insert two AAA batteries following the same

orientation depicted inside the battery chamber

(+/-).

3. Reinstall the rear cover.

4. If the remote control will not be used for

extended periods of time, the batteries should be

removed.

Notes:

• Protect the remote control from high

temperatures, and keep it away from radiation

exposure.

• Keep the control panel receiver out of direct

sunlight.

• Do not mix old and new batteries.

• Do not mix alkaline, standard (carbon-zinc), or

rechargeable (ni-cad, ni-mh,etc) batteries.

• The remote operates within a range of 8 meters

(26 ft.) from the receiver located inside the main

appliance. Any obstruction between the receiver

and remote may cause signal interference,

limiting the ability to program the main unit.

OPERATING INSTRUCTIONS

REMOTE CONTROL REGULATIONS

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

1. Reorient or relocate the receiving antenna

2. Increase the separation between the equipment and receiver

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

4. Consult the dealer or an experienced radio/TV technician for help

Changes or modiﬁ cations not approved by the party responsible for FCC and Industry Canada compliance

could void the user’s authority to operate the equipment. This appliance complies with Part 15 of the FCC

Rules and license-exempt RSS standards. Operation is subject to the following conditions:

1. This device may not cause interference.

2. This device must accept any interference received, including interference that may cause undesired

operation.

This equipment complies with FCC RF and IC RSS-102 radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm

(8 inches) between the radiator and your body.

This device complies with RSS-247 of Industry Canada. Operation is subject to the condition that this

device does not cause harmful interference. This device complies with Canadian CAN ICES-003(B)/NMB-

003(B)

This device contains:

FCC ID: 2ADQOMDNA21

IC: 12575A-MDNA21

SUPPLIER’S DECLARATION OF CONFORMITY

47 CFR § 2.1077 Compliance Information

Unique Identiﬁ er: Danby, RG57J2(B)/BGCEU1

Responsible Party U.S. Contact Information:

Danby Products Inc.

1800 Production Drive

Findlay, OH

45840

Telephone number or internet contact information: Danby.com

FCC Compliance Statement: This appliance complies with Part 15 of the FCC Rules. Operation is subject to

the following conditions:

1. This device may not cause interference.

2. This device must accept any interference received, including interference that may cause undesired

operation.

OPERATING INSTRUCTIONS

ENERGY SAVER FUNCTION

The energy saver function is only available on the

remove control in cool mode. It will automatically

cycle the fan on and off when the compressor is not

in use to minimize how often the compressor needs

to turn on.

The fan will continue to run for 3 minutes after the

compressor turns off. The fan will then cycle on for

2 minutes in 10 minute intervals until the ambient

temperature is above the set temperature, at which

point the compressor will turn on and cooling will

resume.

SLEEP FUNCTION

The sleep function can be used to conserve energy

during sleeping hours.

When selected, the set temperature will increase

by 1°C/2°F every half hour for one full hour. The

appliance will hold the new set temperature for

6 hours before automatically returning to normal

operation.

The sleep function can be canceled at any time by

pressing the sleep button.

WIRELESS CONNECTION

This appliance can be controlled with a wireless

application on your wireless device.

Visit https://www.danby.com/support/apps to

download the application and learn about its

operation.

SHORTCUT FUNCTION

The shortcut function is only available on the remote

control. It can be used to set a favourite setting.

1. Set the appliance to the temperature and fan

speed that you would like to set as a favourite.

2. Press and hold the shortcut button for 2 seconds.

3. Press the shortcut button at any point in future to

return to the favourite setting.

If no favourite is set, pressing the shortcut button will

cause the appliance to run in auto mode at 29°C

(79°F), with fan speed set to auto.

TIMER FUNCTION

The timer function is only available on the remote

control. It can be used to turn the appliance on or

off after a set period of time.

To set the automatic timer:

1. Press the timer on or timer off button depending

on whether the appliance should turn on or off

after the set period of time.

2. Use the timer buttons to select the desired

amount of time before the appliance should turn

on. The timer buttons will add or subtract time in

30 minute increments up to 10 hours and then in

1 hour increments up to 24 hours.

3. Turning the appliance on or off at any time will

cancel the timer settings.

CARE & MAINTENANCE

CLEANING

To avoid possible electric shock, ensure that the

appliance is unplugged before performing any

cleaning or maintenance.

The outside of the appliance can be wiped clean

with a soft cloth or with a lukewarm, damp cloth if

necessary.

Do not use gasoline, benzene, thinner or any

other chemicals to clean this appliance as these

substances can cause damage to the ﬁ nish and

deformation of plastic parts.

Never pour water directly onto the appliance as this

will cause deterioration of electrical components

and wiring insulation.

END OF SEASON CARE

Before removing the appliance from service for the

year, operate the appliance on high fan mode for

half a day to ensure the inside of the appliance

is dry. This will help avoid the growth of mold or

mildew inside the appliance. Ensure the ﬁ lter is

clean and dry. Store the appliance covered in a dry

location.

Note: When installing or removing the appliance

from the window, ensure that caution is taken to

prevent it from falling backward. It is recommended

that installation or removal is completed with

assistance to prevent injury to persons or damage to

property or the appliance.

DISPOSAL

Check for local regulatory compliance regarding

approved and safe disposal of this appliance.

AIR FILTER

Approximately every two weeks, the ﬁ lter indicator

light on the control panel will illuminate as a

reminder to clean the ﬁ lter.

The air ﬁ lter is located behind the front intake grill.

To remove the air ﬁ lter, grasp the grille on both sides

and gently pull it outwards. Remove the ﬁ lter by

pulling it downwards.

• Use a vacuum cleaner with a soft brush

attachment to remove any large debris or dust

build up from the air ﬁ lter.

• Wash the ﬁ lter in lukewarm, soapy water, below

40°C (104°F), or use a neutral cleaning agent.

• Rinse the ﬁ lter with clean water and dry

thoroughly before reinstalling in the appliance.

Press the ﬁ lter button on the control panel to resume

normal functioning.

Note: Do not operate the appliance without the air

ﬁ lter installed.

ERROR CODES

If the display panel shows any of the below error

codes, unplug the appliance, let it stand for 5-10

minutes and then plug it back in. If the error

persists, call for service.

AS - Ambient temperature sensor error

ES - Evaporator temperature sensor error

E4 - Display board communication error

Lo - Room temperature is lower than 0°C (32°F)

HI - Room temperature is higher than 37°C (99°F)

FREQUENTLY ASKED QUESTIONS TROUBLESHOOTING

Can I leave my air conditioner in place

through the winter?

No, do not leave the air conditioner in the window

during the winter.

What is the electrical rating?

This information can be found on the rating plate

located on the side of the unit.

Can I use an extension cord?

No, an extension cord may not be used.

Is there supposed to be Styrofoam in the

unit?

The Styrofoam that is inside the unit acts as

insulation. Do not remove it. Only remove loose

packaging.

Why do I hear water in the unit?

Water is collected during the air conditioning

process and will drain out of the unit and onto the

ground. This why the unit should be installed on a

slight downward tilt towards the outside.

Why is there frost building up in the unit?

When outdoor temperatures are below 18.3°C

(65°F) frost may form when the air conditioner is in

cooling mode. Switch the air conditioner to fan only

mode until the frost melts.

Air conditioner will not operate

• Plug is not fully inserted into the wall outlet.

• Blown fuse or circuit breaker.

Insufﬁ cient cooling

• Air ﬁ lter is dirty.

• Blocked air ﬂ ow.

• Appliance size is too small for application.

Noise

• Inadequate support in window installation;

double check that all screws are tight and the

installation is secure.

• The air ﬁ lter is dirty or blocked.

• Gurgling sounds are normal, this is coolant

moving inside the appliance.

Water dripping inside

• Appliance is not properly angled to allow water

to drain to the outside

Water dripping outside

• On very hot or humid days dripping water from

the back of the appliance is normal

Odors

• Usually caused by the formation of mold or

mildew on internal wet surfaces.

• Ensure the ﬁ lter is clean.

• Run the air conditioner on fan mode to remove

any internal moisture.

LIMITED IN-HOME APPLIANCE WARRANTY

This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used under the normal operating

conditions intended by the manufacturer.

This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby Products Inc. (U.S.A.) (hereafter

“Danby”) or by an authorized distributor of Danby, and is non-transferable.

TERMS OF WARRANTY

Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided.

First Year

During the rst twelve (12) months, any functional parts of this product found to be defective, will be repaired or replaced, at warrantor’s

option, at no charge to the ORIGINAL purchaser.

To obtain

Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized Service Depot. Any app liance

Service

requiring service outside the limited boundaries of “In Home Service” , it will be the consumer’s responsibility to transport the appliance (at

their own expense) to the original retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Serv ice” below.

Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby service depot, where service

must be performed by a qualied service technician.

If service is performed on the units by anyone other than an authorized service depot, or the unit is used for commercial appli cation, all

obligations of Danby under this warranty shall be void.

Boundaries of

If the appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest service center your unit must be

In Home Service

delivered to the nearest authorized Danby Service Depot, as service must only be performed by a technician qualied and certif ied for

warranty service by Danby. Transportation charges to and from the service location are not protected by this warranty and are t he

responsibility of the purchaser.

Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other c ontents of this appliance, whether due

to any defect of the appliance, or its use, whether proper or improper.

EXCLUSIONS

Save as herein provided, Danby, there are no other warranties, conditions, representations or guarantees, express or implied, m ade or intended by Danby or its

authorized distributors and all other warranties, conditions, representations or guarantees, including any warranties, conditio ns, representations or guarantees

under any Sale of Goods Act or like legislation or statue is hereby expressly excluded. Save as herein provided, Danby shall no t be responsible for any damages

to persons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction o f the unit and by the purchase of

the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or propert y caused by the unit.

GENERAL PROVISIONS

No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:

1) Power failure.

2) Damage in transit or when moving the appliance.

3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.

4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating con ditions

(extremely high or low room temperature).

5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).

6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, oods etc.

7) Service calls resulting in customer education.

8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for out door application).

Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event warranty service is required, present this document to our

AUTHORIZED SERVICE DEPOT.

Danby Products Limited

PO Box 1778, Guelph, Ontario, Canada N1H 6Z9

Telephone: (519) 837-0920 FAX: (519) 837-0449

Danby Products Inc.

PO Box 669, Findlay, Ohio, U.S.A. 45840

Telephone: (419) 425-8627 FAX: (419) 425-8629

04/09

1-800-263-2629

Warranty Service

In-home

Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an authorized service

depot. Any appliance requiring service outside the limited boundaries of “In Home Service”, will be the consumer’s

responsibility to transport at their own expense to the original point of purchase or a service depot for repair. If the

appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest service center, it must

be delivered to the nearest authorized Danby Service Depot by the purchaser.

Transportation charges to and from the service location are not protected by this warranty and are the

responsibility of the purchaser.

During the ﬁrst twenty four (24) months, any functional parts of this product found to be defective, will be repaired

or replaced, at warrantor’s option, at no charge to the original purchaser.

Contact the dealer where the unit was purchased, or contact the nearest authorized Danby service depot, where

service must be performed by a qualiﬁed service technician. If service is performed on the unit by anyone other

than an authorized service depot, all obligations of Danby under this warranty shall be void.

First 24 months

To obtain service

Boundaries of

in-home service

LIMITED “IN HOME” WARRANTY

This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used

under the normal operating conditions intended by the manufacturer.

This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby

Products Inc. (U.S.A.) (hereafter “Danby”) or by an authorized distributor of Danby, and is non-transferable.

TERMS OF WARRANTY

Plastic parts are warranted for thirty (30) days from the date of purchase, with no extensions provided.

Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other

contents of this appliance, whether due to any defect of the appliance, or its use, whether proper or improper.

EXCLUSIONS

Save as herein provided, by Danby, there are no other warranties, conditions, representations or guarantees, express or implied, made

or intended by Danby or its authorized distributors and all other warranties, conditions, representations or guarantees, including any

warranties, conditions, representations or guarantees under any Sale of Goods Act or like legislation or statute is hereby expressly

excluded. Save as herein provided, Danby shall not be responsible for any damages to persons or property, including the unit itself,

howsoever caused or any consequential damages arising from the malfunction of the unit and by the purchase of the unit, the

purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or property caused by

the unit.

GENERAL PROVISIONS

No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:

1) Power failure.

2) Damage in transit or when moving the appliance.

3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.

4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating

conditions (ie. extremely high or low room temperature).

5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).

6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, ﬂoods etc.

7) Service calls resulting in customer education.

8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for outdoor

application, including but not limited to: garages, patios, porches or anywhere that is not properly insulated or climate controlled).

Proof of purchase date will be required for warranty claims; retain bills of sale. In the event that warranty service is required, present

the proof of purchase to our authorized service depot.

Warranty Service

In Home

Danby Products Limited

PO Box 1778, Guelph, Ontario, Canada N1H 6Z9

Telephone: (519) 837-0920 FAX: (519) 837-0449

Danby Products Inc.

PO Box 669, Findlay, Ohio, U.S.A. 45840

Telephone: (419) 425-8627 FAX: (419) 425-8629

1-800-263-2629

04/17

Bienvenue dans la famille Danby.

Nous sommes ﬁ ers de nos produits de qualité et nous croyons en un service ﬁ able. Nous

vous suggérons de lire ce manuel du propriétaire avant de brancher votre nouvel appareil

car il contient des informations de fonctionnement importantes, des informations de

sécurité, des conseils de dépannage et d’entretien pour assurer la ﬁ abilité et la longévité de

votre appareil.

Vous avez droit à la couverture de la garantie décrite dans le manuel du propriétaire fourni

avec votre nouvel appareil.

1. Veuillez noter ci-dessous les informations relatives à votre appareil. Vous devez

conserver la preuve d’achat originale pour valider et bénéﬁ cier des services de

garantie.

2. Enregistrez votre produit en ligne et recevez une PROLONGATION DE GARANTIE

GRATUITE DE 2 MOIS après avoir rempli une enquête sur les produits, à l’adresse

www.danby.com/support/product-registration/

Besoin d’assistance?

1. Lisez votre manuel du propriétaire pour obtenir de l’aide à l’installation, au dépannage

et à la maintenance.

2. Visitez www.Danby.com pour accéder aux outils en libre-service, aux FAQ et bien plus

encore en recherchant votre numéro de modèle dans la barre de recherche.

3. Pour bénéﬁ cier du service client le plus rapide, veuillez remplir le formulaire Web à

l’adresse www.danby.com/support. Votre soumission ira directement à un expert de

votre appareil particulier. Nos temps de réponse moyens sont compris entre 20 minutes

et 2 heures, pendant les heures ouvrables EST.

4. Composez le 1-800-263-2629 - veuillez noter que pendant les heures de pointe, les

temps d’attente peuvent dépasser une heure.

Numéro de modèle : _______________________________________________

Numéro de serie : _________________________________________________

Date d’achat : _____________________________________________________

La page charge ...

Danby DAC120B6WDB-6 Air Conditioner Le manuel du propriétaire

Marque: Danby

Modèle: DAC120B6WDB-6 Air Conditioner

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Danby DAC120B6WDB-6 Air Conditioner Owner's manual
español: Danby DAC120B6WDB-6 Air Conditioner El manual del propietario

Danby DAC120B6WDB-6 Air Conditioner Le manuel du propriétaire

Danby DAC120B6WDB-6 Air Conditioner Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents