Skil 5164 Instructions Manual

Marque: Skil

Modèle: 5164

Catégorie: Outils électroportatifs

Taper: Instructions Manual

Ce manuel convient également à

FIN

SKIL Europe BV - Konijnenberg 60 07/05 2609001363

4825 BD Breda - The Netherlands

www.skileurope.com

CIRCULAR SAW

5150 (F0155150..)

INSTRUCTIONS page 8

INSTRUCTIONS page 11

HINWEISE Seite 15

INSTRUCTIES bladz. 20

INSTRUKTIONER sida 24

INSTRUKTION side 27

ANVISNINGEN side 31

OHJEET sivu 35

INSTRUCCIONES pág. 39

INSTRUÇÕES pág. 43

ISTRUZIONI pag. 47

LEÍRÁS oldal 51

POKYNY strana 56

KILAVUZ sayfa 59

INSTRUKCJA strona 63

ИНСТРУКЦИИ страница 68

O∆ΗΓΙΕΣ σελιδα 72

INSTRUCTIUNI pagina 78

YKA3AНИЕ страница 82

POKYNY strana 87

SKIL Nr.

ACCESSORIES

5150

750 W

2,9 kg

34 mm

45°

50 mm

90°

4600

110 mm

MIN.

16 mm

160 mm

MAX.

16 mm

12x 160 mm 16 mm 1,5 / 2,4 2610392349

2610387402

L M P Q

Ø 34-35 mm

NOT INCLUDED

D C C

3 mm

50mm

≥ 50mm

90°

0°

Circular saw 5150

INTRODUCTION

● This tool is intended for lengthways and crossways

cutting of wood with straight cuts as well as angle cuts to

45°; with the appropriate saw blades also non-ferrous

metals, light building materials and plastics can be cut

● Read and save this instruction manual

TECHNICAL SPECIFICATIONS 1

SAFETY

GENERAL SAFETY INSTRUCTIONS

WARNING! Read all instructions. Failure to follow all

instructions listed below may result in electric shock, fire

and/or serious injury. The term "power tool" in all of the

warnings listed below refers to your mains operated

(corded) power tool. SAVE THESE INSTRUCTIONS.

1) WORK AREA

a) Keep work area clean and well lit. Cluttered and dark

areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which

may ignite the dust or fumes.

c) Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of

electric shock.

b) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electric shock.

e) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric

shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in

serious personal injury.

b) Use safety equipment. Always wear eye protection.

Safety equipment such as dust mask, non-skid safety

shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Avoid accidental starting. Ensure the switch is in the

off position before plugging in. Carrying power tools

with your finger on the switch or plugging in power tools

that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal

injury.

e) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of these devices

can reduce dust related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was

designed.

b) Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source before

making any adjustments, changing accessories, or

storing power tools. Such preventive safety measures

reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in

accordance with these instructions and in the

manner intended for the particular type of power

tool, taking into account the working conditions and

the work to be performed. Use of the power tool for

operations different from those intended could result in a

hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is

maintained.

SAFETY INSTRUCTIONS FOR CIRCULAR SAWS

DANGER

● Keep hands away from cutting area and the blade;

keep your second hand on front handle (if both hands

are holding the saw, they can not be cut by the blade)

● Do not reach underneath the workpiece (the guard

cannot protect you from the blade below the workpiece)

● Adjust the cutting depth to the thickness of the

workpiece (less than a full tooth of the blade teeth

should be visible below the workpiece)

● Never hold piece being cut in your hands or across

your leg (it is important to support the work properly to

minimise body exposure, blade binding, or loss of

control)

● Hold tool by insulated gripping surfaces when

performing an operation where the cutting tool may

contact hidden wiring or its own cord (contact with a

"live" wire will also make exposed metal parts of the tool

"live" and shock the operator)

● When ripping always use a rip fence or straight edge

guide (this improves the accuracy of cut and reduces the

chance for blade binding)

● Always use blades with correct size and shape of

arbor holes (diamond or round) (blades that do not

match the mounting hardware of the saw will run

eccentrically, causing loss of control)

● Never use damaged or incorrect blade washers or

bolts (the blade washers and bolt were specially

designed for your saw, for optimum performance and

safety of operation)

KICKBACK - CAUSES

● Kickback is a sudden reaction to a pinched, bound or

misaligned saw blade, causing an uncontrolled saw to lift

up and out of the workpiece toward the operator

● When the blade is pinched or bound tightly by the kerf

closing down, the blade stalls and the motor reaction

drives the unit rapidly back toward the operator

● If the blade becomes twisted or misaligned in the cut, the

teeth at the back edge of the blade can dig into the top

surface of the wood causing the blade to climb out of the

kerf and jump back towards operator

KICKBACK - OPERATOR PREVENTION

Kickback is the result of tool misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below

● Maintain a firm grip with both hands on the saw and

position your arms to resist kickback forces;

position your body to either side of the blade, but

not in line with the blade (kickback could cause the

saw to jump backwards, but kickback forces can be

controlled by the operator, if proper precautions are

taken)

● When blade is binding, or when interrupting a cut for

any reason, release the trigger and hold the saw

motionless in the material until the blade comes to a

complete stop; never attempt to remove the saw

from the work or pull the saw backwards while the

blade is in motion or kickback may occur (investigate

and take corrective actions to eliminate the cause of

blade binding; avoid cutting nails or screws)

● When restarting a saw in the workpiece, centre the

saw blade in the kerf and check that saw teeth are

not engaged into the material (if saw blade is binding,

it may walk up or kickback from the workpiece as the

saw is restarted)

● Support large panels to minimise the risk of blade

pinching and kickback (large panels tend to sag under

their own weight; supports must be placed under the

panel on both sides, near the line of cut and near the

edge of the panel)

● Do not use a dull or damaged blade (unsharpened or

improperly set blades produce narrow kerf causing

excessive friction, blade binding and kickback)

● Blade depth and bevel adjusting locking levers must

be tight and secure before making cut (if blade

adjustment shifts while cutting, it may cause binding and

kickback)

● Use extra caution when making a plunge cut into

existing walls or other blind areas (the protruding

blade may cut objects that can cause kickback)

WARNING

● Check lower guard for proper closing before each

use

● Do not operate the saw if lower guard does not move

freely and close instantly

● Never clamp or tie the lower guard into the open

position

● If saw is accidentally dropped, lower guard may be bent;

raise the lower guard with the retracting handle and

make sure it moves freely and does not touch the blade

or any other part, in all angles and depths of cut

● Check the operation of the lower guard spring; if the

guard and the spring are not operating properly, they

must be serviced before use (lower guard may operate

sluggishly due to damaged parts, gummy deposits, or a

build-up of debris)

● Lower guard should be retracted manually only for

special cuts such as plunge cuts and compound

cuts; raise lower guard by retracting handle and as

soon as blade enters the material, the lower guard

must be released (for all other sawing, the lower guard

should operate automatically)

● Always observe that the lower guard is covering the

blade before placing saw down on bench or floor

(an unprotected, coasting blade will cause the saw to

walk backwards, cutting whatever is in its path; be aware

of the time it takes for the blade to stop after switch is

released)

● Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start cutting

● When you put away the tool, switch off the motor and

ensure that all moving parts have come to a complete

standstill

● Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

● In case of jamming or electrical or mechanical

malfunction, immediately switch off the tool and

disconnect the plug

● SKIL can assure flawless functioning of the tool only

when original accessories are used

● Use only accessories with an allowable speed matching

at least the highest no-load speed of the tool

● Never use the tool without the original protection guard

system

● This tool should not be used by people under the age of

16 years

● The noise level when working can exceed 85 dB(A);

wear ear protection

● If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

● Never use tool when cord is damaged; have it replaced

by a qualified person

● Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

● This tool is not suitable for wet cutting

● After switching off your circular saw, never stop the

rotation of the saw blade by a lateral force applied

against it

● Never use circular saw blades made of high speed steel

(HSS)

● Never use grinding/cutting discs with this tool

● Do not cut material containing asbestos

● Wear a dust protection mask when working with

materials which produce dust that is detrimental to

health; inform yourself beforehand about the materials to

be worked on

● Do not attempt to cut extremely small workpieces

● Remove all obstacles on top of as well as underneath

the cutting path before you start cutting

● Do not work overhead with the tool

● Only use a saw table provided with a switch that

prevents restarting of the motor after interruption of

voltage

● Only use a saw table provided with a kerf guide

● Always disconnect plug from power source before

making any adjustment or changing any accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

● Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

● If for any reason the old plug is cut off the cord of this

tool, it must be disposed of safely and not left unattended

USE

● Changing saw blade 3

- open lower guard A by using lever B

- change saw blade with saw teeth and arrow printed

on saw blade pointing in same direction as arrow on

lower guard A

! make sure that clamping surfaces C of flanges are

perfectly clean and face the blade

- tighten blade bolt D with hex key 1/8 turn past finger

tight (ensures slippage of saw blade when it

encounters excessive resistance thus reducing motor

overload and saw kickback)

● Adjusting cutting depth (0-50 mm) 4

- for an optimal quality cut the saw blade should not

extend more than 3 mm below the workpiece

- loosen lever E

- raise/lower foot F until desired cutting depth is set on

scale using indicator G

- tighten lever E

● Readjusting clamping lever

Clamping power of lever E can be readjusted

- unscrew lever E and set it at at least 30° counter-

clockwise

- screw tight lever E again

● Adjusting cutting angle (0-45°) 5

- loosen 2 knobs H

- tilt tool until desired cutting angle is set on scale using

indicator J

- tighten 2 knobs H

! when bevel cutting, cutting depth does not

correspond with value on cutting depth scale

● 90° Cutting angle check 5

- adjust and tighten foot F to maximum cutting depth 4

- adjust and tighten cutting angle to 0°

- check for 90° angle between the blade and bottom of

foot with a square

● Adjustable saw line visor K 6a

- for guiding tool along desired line of cut marked on the

workpiece

- for a straight 0° cut or a 45° bevel cut use the indicator

line concerned

! the wide part of the foot should rest on the

supported part of the workpiece

- can be adjusted to allow you to choose whether waste

material is on inner or outer side of blade 6a+b

! cutting width is determined by width of blade

teeth and not by width of blade body

! always make trial cuts first to verify actual line of

cut

● Dust suction

- connect vacuum cleaner to extension L 2

! never let the vacuum cleaner hose interfere with

the lower guard or the cutting operation

- one may also use a dust bag (SKIL accessory

2610387402)

● Operating the tool 2

- connect plug with power source

- always hold handle M firmly with one hand and

handle N firmly with the other hand

- place tool with front end of foot flat on workpiece

! ensure that the saw teeth are not engaged into the

workpiece

- switch on tool by first pressing knob P (= safety switch

which cannot be locked) and then pulling trigger Q

! the tool should run at full speed before the blade

enters into the workpiece

- lower guard A opens automatically when saw blade

enters the workpiece (open lower guard manually by

using lever B only for special cuts such as plunge

cuts)

- do not force the tool; apply light and continuous

pressure

- after completing the cut switch off tool by releasing

trigger Q

! ensure that the blade has come to a complete

standstill, before you lift the tool from the

workpiece

APPLICATION ADVICE

● Always face the good side of the workpiece down to

ensure minimum splintering

● Only use sharp saw blades of the correct type 7

- quality of cut improves by the number of teeth

- carbide tipped blades stay sharp up to 30 times longer

than ordinary blades

● Rip fence R 8

- for making exact cuts along a workpiece edge

- can be inserted in either side of foot

Adjusting rip fence

- loosen knob S

- adjust to desired cutting width by using rip fence scale

(use saw line visor K as 0-reference)

- tighten knob S

● Plunge cutting 9

- set desired cutting depth

- tilt tool forward with saw line visor K lined up with

desired line of cut marked on the workpiece

- open lower guard A with lever B

- just before blade enters workpiece, switch on tool and

gradually lower back end of tool using front end of foot

as hinge-point

- gradually move tool downward as well as forward

- as soon as blade enters the material, release lever B

! never pull tool backwards

● Cutting large panels 0

- support panel close to the cut either on floor, table or

workbench

! set cutting depth so that you cut through panel

and not through support

- in case rip fence does not allow desired width of cut,

clamp or nail straight piece of wood to workpiece as a

guide, and use the right side of the foot against this

guide

● For more tips see www.skileurope.com

GUARANTEE / ENVIRONMENT

● Always keep tool and cord clean (especially the

ventilation slots)

! disconnect the plug before cleaning

● Clean saw blade immediately after use (especially from

resin and glue)

● This SKIL product is guaranteed in accordance with

statutory/country-specific regulations; damage due to

normal wear and tear, overload or improper handling will

be excluded from the guarantee

● In case of a complaint, send the tool undismantled

together with proof of purchase to your dealer or the

nearest SKIL service station (addresses as well as the

service diagram of the tool are listed on

www.skileurope.com)

● Dispose of the tool by sorting tool, accessories and

packaging for environment-friendly recycling (the plastic

components are labeled for categorized recycling)

Scie circulaire 5150

INTRODUCTION

● Cet outil est conçu pour effectuer dans le bois des

coupes droites longitudinales et transversales ainsi que

des angles d’onglet jusqu’à 45°; muni de lames de scie

correspondantes, il est capable de scier des matériaux

non-ferroux, des matériaux de construction légers et des

matières plastiques

● Lisez et conservez ce manuel d’instruction

SPECIFICATIONS TECHNIQUES 1

SECURITE

INSTRUCTIONS GENERALES DE SECURITE

ATTENTION! Lisez toutes les instructions. Le non-

respect des instructions indiquées ci-après peut entraîner

un choc électrique, un incendie et/ou de graves blessures

sur les personnes. La notion d’«outil électroportatif»

mentionnée par la suite se rapporte à des outils électriques

raccordés au secteur (avec câble de raccordement).

GARDEZ PRECIEUSEMENT CES INSTRUCTIONS DE

SECURITE.

1) PLACE DE TRAVAIL

a) Maintenez l’endroit de travail propre et bien éclairé.

Un lieu de travail en désordre ou mal éclairé augmente

le risque d’accidents.

b) N’utilisez pas l’appareil dans un environnement

présentant des risques d’explosion et où se trouvent

des liquides, des gaz ou poussières inflammables.

Les outils électroportatifs génèrent des étincelles

risquant d’enflammer les poussières ou les vapeurs.

c) Tenez les enfants et autres personnes éloignés

durant l’utilisation de l’outil électroportatif.

En cas d’inattention vous risquez de perdre le contrôle

sur l’appareil.

2) SECURITE RELATIVE AU SYSTEME ELECTRIQUE

a) La fiche de secteur de l’outil électroportatif doit être

appropriée à la prise de courant. Ne modifiez en

aucun cas la fiche. N’utilisez pas de fiches

d’adaptateur avec des appareils avec mise à la terre.

Les fiches non modifiées et les prises de courant

appropriées réduisent le risque de choc électrique.

b) Evitez le contact physique avec des surfaces mises

à la terre tels que tuyaux, radiateurs, fours et

réfrigérateurs. Il y a un risque élevé de choc électrique

au cas où votre corps serait relié à la terre.

c) N’exposez pas l’outil électroportatif à la pluie ou à

l’humidité. La pénétration d’eau dans un outil

électroportatif augmente le risque d’un choc électrique.

✎

05 SKIL Europe B.V. A. v.d. Kloot

CE DECLARATION OF CONFORMITY We declare under our sole

responsibility that this product is in conformity with the following

standards or standardized documents: EN 60 745, EN 55 014, in

accordance with the provisions of the directives 73/23/EEC,

89/336/EEC, 98/37/EEC. NOISE/VIBRATION Measured in

accordance with EN 60 745 the sound pressure level of this tool is

98 dB(A), the sound power level 109 dB(A) and the vibration

< 2.5 m/s

(hand-arm method).

CE DÉCLARATION DE CONFORMITÉ Nous déclarons sous notre

propre responsabilité que ce produit est en conformité avec les

normes ou documents normalisés suivants: EN 60 745, EN 55 014,

conforme aux réglementations 73/23/EEC, 89/336/EEC, 98/37/EEC.

BRUIT/VIBRATION Mesuré selon EN 60 745 le niveau de la pression

sonore de cet outil est 98 dB(A), le niveau de la puissance sonore

109 dB(A) et la vibration < 2,5 m/s

(méthode main-bras).

CE KONFORMITÄTSERKLÄRUNG Wir erklären in alleiniger

Verantwortung, daß dieses Produkt mit den folgenden Normen oder

normativen Dokumenten übereinstimmt: EN 60 745, EN 55 014,

gemäß den Bestimmungen der Richtlinien 73/23/EWG,

89/336/EWG, 98/37/EWG.

GERÄUSCH/VIBRATION Gemessen gemäß EN 60 745 beträgt der

Schalldruckpegel dieses Gerätes 98 dB(A), der Schalleistungspegel

109 dB(A) und die Vibration < 2,5 m/s

(Hand-Arm Methode).

CE CONFORMITEITSVERKLARING Wij verklaren, dat dit product

voldoet aan de volgende normen of normatieve documenten:

EN 60 745, EN 55 014, overeenkomstig de bepalingen van de

richtlijnen 73/23/EEG, 89/336/EEG, 98/37/EEG.

GELUID/VIBRATIE Gemeten volgens EN 60 745 bedraagt het

geluidsdrukniveau van deze machine 98 dB(A), het geluidsvermogen-

niveau 109 dB(A) en de vibratie < 2,5 m/s

(hand-arm methode).

CE KONFORMITETSFÖRKLARING Vi intygar och ansvarar för, att

denna produkt överensstämmer med följande norm och dokument:

EN 60 745, EN 55 014, enl. bestämmelser och riktlinjema

73/23/EWG, 89/336/EWG, 98/37/EWG.

LJUD/VIBRATION Ljudtrycksnivån som uppmätts enligt

EN 60 745 är på denna maskin 98 dB(A), ljudeffektnivån

109 dB(A) och vibration < 2,5 m/s

(hand-arm metod).

CE KONFORMITETSERKLÆRING Vi erklærer under almindeligt

ansvar, at dette produkt er i overensstemmelse med følgende normer

eller normative dokumenter: EN 60 745, EN 55 014, i henhold til

bestemmelserne i direktiverne 73/23/EØF, 89/336/EØF, 98/37/EØF.

STØJ/VIBRATION Måles efter EN 60 745 er lydtrykniveau af dette

værktøj 98 dB(A), lydeffektniveau 109 dB(A) og vibrationsniveauet

< 2,5 m/s

(hånd-arm metoden).

CE SAMSVARSERKLÆRING Vi erklærer at det er under vårt

ansvar at dette produkt er i samsvar med følgende standarder eller

standard- dokumenter: EN 60 745, EN 55 014, i samsvar med

reguleringer 73/23/EWG, 89/336/EWG, 98/37/EWG.

STØY/VIBRASJON Målt ifølge EN 60 745 er lydtrykknivået av dette

verktøyet 98 dB(A), lydstyrkenivået 109 dB(A) og vibrasjonsnivået

< 2,5 m/s

(hånd-arm metode).

CE TODISTUS STANDARDINMUKAISUUDESTA Todistamme

täten ja vastaamme yksin siitä, että tämä tuote en allalueteltujen

standardien ja standardoimisasiakirjojen vaatimusten mukainen

EN 60 745, EN 55 014, seuraavien sääntöjen mukaisesti

73/23/EWG, 89/336/EWG, 98/37/EWG.

MELU/TÄRINÄ Mitattuna EN 60 745 mukaan työkalun melutaso on

98 dB(A), yleensä työkalun äänen voimakkuus on 109 dB(A) ja

tärinän voimakkuus < 2,5 m/s

(käsi-käsivarsi metodi).

CE DECLARACION DE CONFORMIDAD Declaramos bajo nuestra

sola responsabilidad que este producto está en conformidad con las

normas o documentos normalizados siguientes: EN 60 745, EN 55 014,

de acuerdo con las regulaciones 73/23/CEE, 89/336/CEE, 98/37/CEE.

RUIDOS/VIBRACIONES Medido según EN 60 745 el nivel de la

presión acústica de esta herramienta se eleva a 98 dB(A), el nivel

de la potencia acústica 109 dB(A) y la vibración a < 2,5 m/s

(método brazo-mano).

CE DECLARAÇÃO DE CONFIRMIDADE Declaramos sob nossa

exclusiva responsabilidade que este producto cumpre as seguintes

normas ou documentos normativos: EN 60 745, EN 55 014, conforme

as disposições das directivas 73/23/CEE, 89/336/CEE, 98/37/CEE.

RUÍDO/VIBRAÇÕES Medido segundo EN 60 745 o nível de

pressão acústica desta ferramenta é 98 dB(A), o nível de potência

acústica 109 dB(A) e a vibração < 2,5 m/s

(método braço-mão).

CE DICHIARAZIONE DI CONFORMITÀ Dichiaramo, assumendo

la piena responsabilità di tale dichiarazione, che il prodotto è conforme

alle seguenti normative e ai relativi documenti: EN 60 745, EN 55 014 in

base alle prescrizioni delle direttive CEE 73/23, CEE 89/336, CEE 98/37.

RUMOROSITÀ/VIBRAZIONE Misurato in conformità al EN 60 745 il

livello di pressione acustica di questo utensile è 98 dB(A), il livello di

potenza acustica 109 dB(A) e la vibrazione < 2,5 m/s

(metodo

mano-braccio).

CE MINÖSÉGI TANUSITVANY Teljes felelösségünk tudatában

kijelentjük, hogy jelen termék a következö szabványoknak vagy

kötelezö hatósági elöírásoknak megfelel: EN 60 745, EN 55 014, a

73/23/EWG, 89/336/EWG, 98/37/EWG elöírásoknak megfelelöen.

ZAJ/REZGÉS Az EN 60 745 alapján végzett mérések szerint ezen

készülék hangnyomás szintje 98 dB(A), hangteljesítmény szintje

109 dB(A) a kézre ható rezgésszám < 2,5 m/s

CE STRVZUJÍCÍ PROHLÅ◊ENÍ Potvrzujeme na odpovπdnost, Ωe

tento v¥robek odpovídå nåsledujícím normåm nebo normativním

podkladüm: EN 60 745, EN 55 014, podle ustanovení smπrnic

73/23/EWG, 89/336/EWG, 98/37/EWG.

HLUÇNOSTI/VIBRACÍ Mπ®eno podle EN 60 745 çiní tlak hlukové

vlny tohoto p®ístroje 98 dB(A), dávka hluçnosti 109 dB(A) a vibrací

< 2,5 m/s

(metoda ruka-paΩe).

CE STANDARDIZASYON BEYANI Ye¤ane sorumlu olarak, bu

ürünün aﬂa¤ıdaki standartlara veya standart belgelerine uygun

oldu¤unu beyan ederiz: EN 60 745, EN 55 014, yönetmeli¤i

hükümleri uyarınca 73/23/AET, 89/336/AET, 98/37/AET.

GÜRÜLTÜ

T‹TREﬁIM Ölçülen EN 60 745 göre ses basıncı bu

makinanın seviyesi 98 dB(A), çal›ﬂma s›ras›ndaki gürültü 109 dB(A)

ve titreﬂim < 2,5 m/s

(el-kol metodu).

OÂWIADCZENIE ZGODNOÂCI CE Niniejszym oÊwiadczamy

ponoszàc osobistà odpowiedzialnoÊç, ˝e produkt wykonany jest

zgodnie z nast´pujàcymi normami i dokumentami normalizujàcymi:

EN 60 745, EN 55 014, z godnie z wytycznymi 73/23/EWG,

89/336/EWG, 98/37/EWG.

HA¸ASU/WIBRACJE Pomiarów dokonano zgodnie z normà EN 60 745

ciÊnienie akustyczne narz´dzia wynosi 98 dB(A), poziom mocy

akustycznej 109 dB(A), zaÊ wibracje < 2,5 m/s

(metoda d∏oƒ-r´ka).

ЗАЯВЛЕНИЕ О СООТВЕТСТВИИ Мы с полной

ответственностыо заявляем, что это изделие соответствует

следующим стандартам или стандартизованным документам:

EN 60 745, EN 55 014, в соответсувии с инструкциями

73/23/EEC, 89/336/EEC, 98/37/EEC.

ШУМНОСТИ/ВИБРАЦИИ При измерении в соответствии co

стандартoм EN 60 745 уровень звукового давления для этого

инструмента составляет 98 дБ (A), уровeнь звуковой мощности -

109 дБ (A) и вибрации - < 2,5 м/с

(по методу для рук).

CE ∆ΗΛΩΣΗ ΣYMBATOTΗΤΑΣ ∆ηλ¸ύµε υπευθύνως τι τ¸

πρ¸ϊν αυτ είναι κατασκευασµέν¸ σύµ¡ωνα µε τ¸υς εής

καν¸νισµ¸ύς ή κατασκευαστικές συστάσεις: EN 60 745,

EN 55 014, κατά τις διατάεις των καν¸νισµών της Κ¸ινής

Αγ¸ράς 73/23/EEC, 89/336/EEC, 98/37/EEC.

Θ^ΡYΒ^/ΚΡΑ∆ΑΣΜ^YΣ Μετρηµένη σύµ¡ωνα µε EN 60 745

η στάθµη ακ¸υστικής πίεσης αυτ¸ύ τ¸υ εργαλεί¸υ ανέρÅεται

σε 98 dB(A), η στάθµη ηÅητικής ισÅύoς σε 109 dB(A) και ¸

κραδασµς σε < 2,5 m/s

(µεθ¸δ¸ς Åειρς/ραÅί¸να).

DECLARAØIE DE CONFORMITATE CE Declaråm pe proprie

råspundere cå acest product este conform cu urmåtoarele

standarde sau documente standardizate: EN 60 745, EN 55 014, în

conformitate cu regulile 73/23/EEC, 89/336/EEC, 98/37/EEC.

ZGOMOT/VIBRAØII Måsurat în conformitate cu EN 60 745 nivelul

de presiune a sunetului generat de acest instrument este de

98 dB(A), nivelul de putere a sunetului 109 dB(A) iar nivelul

vibraøiilor < 2,5 m/s

(metoda mînå - braø).

CE ДЕKЛАPAЦИЯ ЗA CБOTВETCTBИE Декларираме на

изцяло наша отговорност, че това изделие е съобразено със

следните стандарти или стандартизирани документи:

EN 60 745, EN 55 014, в съответствие с нормативната уредба

на 73/23/EEC, 89/336/EEC, 98/37/EEC.

ШУМ/ВИБPAЦИИ Измерено в съответствие с EN 60 745 нивото

на звуково налягане на този инструмент е 98 dB(A),

нивото на звукова мощност е 109 dB(A), а вибрациите са

< 2,5 m/s

(метод ръка-рамо).

CE PREHLÁSENIE O ZHODE Vÿhradne na na√u vlastnú

zodpovednos† prehlasujeme, Ωe tento vÿrobok zodpovedá

nasledujúcim normám alebo normovanÿm dokumentom:

EN 60 745, EN 55 014, v súlade s predpismi 73/23/EEC,

89/336/EEC, 98/37/EEC.

HLUKU/VIBRÁCIÁCH Merané pod¬a EN 60 745 je úroveµ

akustického tlaku tohto nástroja 98 dB(A), úroveµ akustického

vÿkonu je 109 dB(A) a vibrácie sú < 2,5 m/s

(metóda ruka - paΩa).

FIN

Skil 5164 Instructions Manual

Marque: Skil

Modèle: 5164

Catégorie: Outils électroportatifs

Taper: Instructions Manual

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

italiano: Skil 5164
English: Skil 5164
dansk: Skil 5164

Skil 5164 Instructions Manual

Ce manuel convient également à

Skil 5164 Instructions Manual

dans d''autres langues

Documents connexes

Autres documents