Ryobi RY401012 Le manuel du propriétaire

Marque: Ryobi

Modèle: RY401012

Catégorie: Tondeuses à gazon

Taper: Le manuel du propriétaire

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

20 in. 40 VOLT LAWN MOWER

20 po, TONDEUSE 40 V

20 pulg., PODADORA 40 V

RY40LM03

 Important Safety Instructions ......... 2-4

Symbols

......................................... 5-6



Features .............................................7



Assembly ....................................... 8-9



Operation ..................................... 9-11



Maintenance .............................. 12-13



Troubleshooting ...............................14



Parts Ordering and

Service ............................... Back Page



Instructions importantes

concernant la securite ..................... 2-4

Symboles

....................................... 5-6



Caractéristiques .................................7



Assemblage ................................... 8-9



Utilisation ..................................... 9-11



Entretien ..................................... 12-13



Dépannage ....................................... 14



Commande de pièces

et réparation ..................... Page arrière



Instrucciones de seguidad

importantes .................................... 2-4

Símbolos ........................................ 5-6

 Características ...................................7

 Armado .......................................... 8-9

 Funcionamiento ........................... 9-11

 Mantenimiento ........................... 12-13

 Corrección de problemas ................14

 Pedidos de piezas

y servicio ....................... Pág. posterior

WARNING: To reduce the

risk of injury, the user must read and

understand the operator’s manual

before using this product.

AVERTISSEMENT : Pour

réduire les risques de blessures,

l’utilisateur doit lire et veiller à bien

comprendre le manuel d’utilisation

avant d’employer ce produit.

ADVERTENCIA: Para reducir

el riesgo de lesiones, el usuario debe

leer y comprender el manual del

operador antes de usar este producto.

SAVE THIS MANUAL FOR

FUTURE REFERENCE

CONSERVER CE MANUEL

POUR FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL

PARA FUTURAS CONSULTAS

See this fold-out section for all of the figures

referenced in the operator’s manual.

Consulter l’encart à volets afin d’examiner toutes

les figures mentionnées dans le manuel d’utilisation.

Consulte esta sección desplegable para ver todas

las figuras a las que se hace referencia en el manual del operador.

Fig. 1

A - Carrying/lifting handle (poignée de transport/soulèvement, mango de

transporte/elevación)

B - LED headlights (phares DEL, luces delanteras LED)

C - Battery cover (couvercle des piles, tapa de las baterías)

D - Height adjustment lever (levier de réglage de la hauteur, palanca de

ajuste de altura)

E - Handle adjustment knob (bouton de réglage de la poignée, perilla de

ajuste del mango)

F - Lower handle (poignée inférieure, mango inferior)

G - Handle lock lever (levier de verrou de la poignée, palanca de seguro del

mango)

H - Upper handle (poignée supérieure, mango superior)

I - Handle lock (verrou de la poignée, seguro del mango)

J - Start button (bouton de démarrage, botón de arranque)

K - Grass catcher (collecteur d’herbe, receptor de hierba)

L - Start key (clé de démarrage, llave del arranque)

- Mulching plug (insert broyeur, tapón para trituración)

N - Self-propel levers (leviers de fonction automotrice, palancas

autopropulsadas)

iii

Fig. 2

Fig. 3

A - Handle adjustment knob (bouton de réglage de la poignée, perilla de

ajuste del mango)

B - Lower handle (poignée inférieure, mango inferior)

C - To unlock (pour déverrouiller, para desbloquear)

D - To lock (pour verrouiller, para asegurar)

Fig. 4

Fig. 5

A - Clips (attaches, clips)

A - Frame (support, armazón)

B - Bag (sac, bolsa)

C - Handle (poignée, mango)

D - Vinyl floor (plancher en vinyle, piso de vinilo)

E - Clip (attache, clip)

A - Upper handle (poignée supérieure, mango superior)

B - Handle lock lever (levier de verrou de la poignée, palanca de seguro del

mango)

C - Unlocked position (position déverrouillée, posición desbloqueada)

D - Locked position (position engagé, posición trabada)

Fig. 11

A - Start key (clé de démarrage, llave del

arranque)

B - Battery cover (couvercle des piles, tapa de

las baterías)

C - Start key slot (fente de la clé de démarrage,

ranura de la llave del arranque)

A - Battery pack (bloc-piles, paquete de

baterías)

B - Battery cover (couvercle des piles, tapa de

las baterías)

C - Battery storage compartment (compartiment

de rangement de pile, compartimiento de

almacenamiento de la batería)

D - Latch (loquet, pestillo)

E - Battery port (logement de piles,

compartimiento de la batería)

Fig. 9

A - Height adjustment lever (levier de réglage de

la hauteur, palanca de ajuste de altura)

B - Lowest blade setting (le plus bas réglage de

la lame, ajuste más bajo de la hoja)

C - Highest blade setting (le plus haut réglage

de la lame, ajustes de cuchilla más alto)

Fig. 7

Fig. 10

Fig. 12

A - Handle (poignée, mango)

B - Slot (fente, ranura)

C - Metal lock (verrou de métal, dispositivo de

seguridad de metal)

Fig. 8

A - Rear discharge opening (ouverture d’éjection

arrière, abertura de descarga posterio)

B - Mulching plug (insert broyeur, tapón para

trituración)

C - Metal lock (verrou de métal, dispositivo de

seguridad de metal)

D - Slot (fente, ranura)

E - Handle (poignée, mango)

A - Grass catcher handle (poignée de collecteur

d’herbe, mango del receptor de hierba)

B - Rear discharge opening (ouverture d’éjection

latérale, abertura de descarga lateral)

A - Start button (bouton de démarrage, botón

de arranque)

B - Start levers (leviers de volet de départ,

palancas de arranque)

Fig. 6

15° MAXIMUM

15° MAXIMAL

15° MÁXIMA

Fig. 16

A - Blade (lame, hoja)

B - Wrench (clé, llave)

C - Block of wood (pièce de bois, bloque de

madera)

Fig. 15

Fig. 13

Fig. 14

Fig. 17

Fig. 19

Fig. 18

TO STORE THE MACHINE

IN THE HORIZONTAL POSITION

POUR REMISER L’ÉQUIPEMENT

EN POSITION HORIZONTALE

PARA GUARDAR LA MÁQUINA

EN POSICIÓN HORIZONTAL

TO STORE THE MACHINE

IN THE VERTICAL POSITION

POUR REMISER L’ÉQUIPEMENT

EN POSITION VERTICALE

PARA GUARDAR LA MÁQUINA

EN POSICIÓN VERTICALE

A - Shaft (arbre, eje)

B - Hub (moyeu, buje)

C - Blade post (round) [tiges pour lame (ronde),

montantes de cuchilla (redondo)]

D - Blade post (half circle) [tige pour lame (demi-

cercle), puerto de la hoja (semicircular)]

E - Blade (lame, hoja)

F - Blade hole (half circle) [trou pour lame (demi-

cercle), orificio de la hoja (semicircular)]

G - Blade hole (round) [trou pour lame (ronde),

orificio de la hoja (redondo)]

H - Blade insulator (isolant de lame, aislante de

hoja)

I - Spacer (entretoise, separador)

J - Blade nut (écrou de lame, tuerca de la hoja)

A - Handle lock (verrou de la poignée, seguro

del mango)

B - To lock (pour verrouiller, para asegurar)

C - To unlock (pour déverrouiller, para

desbloquear)

2 — English

WARNING:

READ AND UNDERSTAND ALL INSTRUCTIONS.

Failure to follow all instructions listed below and on the

machine may result in electric shock, fire, and/or serious

personal injury.

READ ALL INSTRUCTIONS

This cutting machine is capable of amputating hands and

feet and throwing objects. Failure to observe all safety

instructions could result in serious injury or death.

Avoid dangerous environment – Do not use the lawn

mower in damp or wet conditions or operate in the rain.

Keep children away – Keep all bystanders, children, and

pets at least 100 ft. away. Stop machine if anyone enters

the area.

Tragic accidents can occur if the operator is not alert to

the presence of children. Children are often attracted to

the machine and the mowing activity. Never assume that

children will remain where you last saw them.

• Keep children out of the mowing area and under the

watchful care of a responsible adult other than the

operator.

• Be alert and turn mower off if a child enters the area.

• Never allow children to operate the machine.

• Use extra care when approaching blind corners, shrubs,

trees, or other objects that may block your view of a

child.

Dress properly – Wear heavy, long pants, long sleeves,

gloves, and protective footwear that will protect your

feet and improve your footing on slippery surfaces. Do

not wear loose fitting clothing, short pants, sandals, or

go barefoot. Do not wear jewelry of any kind. They can

be caught in moving parts.

Don’t overreach – Keep proper footing and balance at all

times. Overreaching can result in loss of balance.

Do not leave the mower unattended while running or with

the start key installed.

Keep hands and feet away from cutting area. Keep clear

of the discharge opening at all times.

Operate the lawn mower only in daylight or good artificial

light.

Use safety glasses – Always wear eye protection with

side shields marked to comply with ANSI Z87.1. Use face

mask if operation is dusty.

Use the right appliance – Do not use the lawn mower for

any job except that for which it is intended.

Do not force the lawn mower – It will do the job better

and safer at the rate for which it was designed.

Do not charge batteries in rain, or in wet locations.

Stay alert – Watch what you are doing and use common

sense when operating the lawn mower. Do not operate

the mower while tired, upset, or under the influence of

drugs, alcohol, or medication. A moment of inattention

while operating the lawn mower may result in serious

personal injury.

Maintain lawn mower with care – Keep machine in good

working condition. Keep blades sharp and guards in place

and in working order. Replace damaged or unevenly worn

blades before using mower for best performance.

Check all nuts, bolts, and screws at frequent intervals for

proper tightness to be sure the equipment is in safe work-

ing condition. Mower blades are sharp. Wrap the blade or

wear gloves, and use extra caution when servicing them.

Do not dispose of the battery in a fire. The cell may

explode. Check with local codes for possible special

disposal instructions.



Stop the motor, wait until the blade comes to a complete

stop, and remove the start key and battery pack before

performing any maintenance, cleaning the lawn mower,

removing the grass catcher, or removing the mulching

plug.

 Never use a hose, water, or any liquids to clean or

rinse off the lawn mower. Corrosive liquids, water, fer-

tilizers, and chemicals used to treat lawns can enter the

lawn mower and/or battery compartment and damage

electronic components and/or the battery pack, which can

result in a short circuit, increased risk of fire, and serious

personal injury. Remove any buildup of grass and leaves

on or around the mower housing and/or underneath the

mower deck. Wipe the mower clean with a dry cloth oc-

casionally.

 Replace blade if it is bent or cracked. An unbalanced

blade causes vibration that could damage the motor

drive unit or cause personal injury. Sharpen a dull blade

equally at each end to maintain the balance. Clean the

blade thoroughly and check its balance by supporting

it horizontally on a thin nail through its center hole. The

nail should be in a horizontal position. If either end of

the blade rotates downward, remove some metal from

the heavy of lower end until the blade is balanced. It is

balanced when neither end drops.

Always use safety protective devices. Do not operate the

mower without the entire grass catcher or mulching plug

and rear discharge door in place and working properly.

Do not open or mutilate the battery. Released electrolyte

is corrosive and may cause damage to the eyes or skin.

It may be toxic if swallowed.

Follow manufacturer’s instructions for proper operation

and installation of accessories. Only use accessories

approved by the manufacturer.

Exercise care in handling batteries in order not to short the

battery with conducting materials such as rings, bracelets,

and keys. The battery or conductor may overheat and

cause burns.

IMPORTANT SAFETY INSTRUCTIONS

3 — English

IMPORTANT SAFETY INSTRUCTIONS

Clear the work area before each use. Remove all objects

such as rocks, tree nuts, sticks, metal, wire, bones, toys,

or other objects which can be thrown by the blade.Stay

behind the handle when the motor is running.

Prevent unintentional starting. Ensure the switch is in the

off-position before connecting to battery pack, picking

up or carrying the appliance. Carrying the appliance with

your finger on the switch or energizing appliance that have

the switch on invites accidents.

When battery pack is not in use, keep it away from other

metal objects, like paper clips, coins, keys, nails, screws

or other small metal objects, that can make a connec-

tion from one terminal to another. Shorting the battery

terminals together may cause burns or a fire.

Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally occurs,

flush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause

irritation or burns.

Do not use a battery pack or appliance that is damaged

or modified. Damaged or modified batteries may exhibit

unpredictable behavior resulting in fire, explosion or risk

of injury.

Do not expose a battery pack or appliance to fire or

excessive temperature. Exposure to fire or temperature

above 265°F may cause explosion.

Follow all charging instructions and do not charge the

battery pack or appliance outside of the temperature

range specified in the instructions. Charging improperly

or at temperatures outside of the specified range may

damage the battery and increase the risk of fire.

Do not modify or attempt to repair the appliance or the

battery pack (as applicable) except as indicated in the

instructions for use and care.

Avoid holes, ruts, bumps, rocks, property stakes, or other

hidden objects. Uneven terrain could cause a slip and fall

accident.



Do not mow near drop-offs, ditches, or embankments.

Mow across the face of slopes, never up and down.

Exercise extreme caution when changing direction on

slopes.

Plan your mowing pattern to avoid discharge of material

toward roads, sidewalks, bystanders and the like. Also,

avoid discharging material against a wall or obstruction,

which may cause the material to ricochet back toward

the operator.

Do not mow on wet grass or excessively steep slopes.

Poor footing could cause a slip and fall accident. Walk,

never run.

Use extra care when approaching blind corners, shrubs,

trees, or other objects that may block your view.

Do not pull the mower backward unless absolutely nec-

essary. If you must back the mower away from a wall or

obstruction, first look down and behind to avoid tripping

or pulling the mower over your feet.

Never direct discharged material toward anyone. Avoid

discharging material against a wall or obstruction. Material

may ricochet back toward the operator. Stop the blade

when crossing gravel surfaces.

Objects struck by the lawn mower blade can cause severe

injuries to persons. The lawn should always be carefully

examined and cleared of all objects prior to each mowing.

If the lawn mower strikes a foreign object, follow these

steps:

• Stop the lawn mower by releasing the blade control

lever, wait until the blade comes to a complete stop,

and then remove start key.

• Thoroughly inspect the mower for any damage.

• Replace the blade if it is damaged in any way. Repair

any damage before restarting and continuing to operate

the mower.

Stop the motor, wait until the blade comes to a complete

stop, and remove start key before unclogging the chute.

The cutting blade continues to rotate for a few seconds

after the motor is shut off. Never place any part of the

body in the blade area until you are sure the blade has

stopped rotating.

If the mower should start to vibrate abnormally, stop the

motor, remove the start key, and check immediately for

the cause. Replace the blade if it is unevenly worn or

damaged in any way. Vibration is generally a warning of

trouble.

Service on the product must be performed by qualified

repair personnel only. Service or maintenance performed

by unqualified personnel could result in injury to the user

or damage to the product.

The grass catcher assembly is subject to deterioration

and wear and should be checked each time the mower is

used. If replacement is needed, make sure the new grass

catcher meets original manufacturer’s recommendations

and specifications.

Use only authorized replacement parts when servicing

the product. Use identical replacement blades only. Use

of unauthorized parts may create a risk of serious injury

to the user, or damage to the product.



Maintain or replace safety instructions labels, as necessary.

Disconnect battery and remove start key. Disconnect

battery pack and remove start key from the appliance

before storing, servicing, or changing accessories such

as blades. Such preventive safety measures reduce the

risk of starting the tool accidentally.

Stop the unit and disconnect battery pack and start key

when not in use. Carry or push the unit with the motor

stopped and the start key removed from the mower.

4 — English

IMPORTANT SAFETY INSTRUCTIONS

Battery tools do not have to be plugged into an electrical

outlet; therefore, they are always in operating condition.

Be aware of possible hazards when not using your bat-

tery tool or when changing accessories. Following this

rule will reduce the risk of electric shock, fire, or serious

personal injury.



Do not use battery-operated appliance in rain.

 Remove or disconnect battery before servicing, cleaning

or removing material from the gardening appliance.

 Use this product only with batteries and chargers listed in

tool/appliance/battery pack/charger correlation supple-

ment 988000-842.

 Store idle lawn mower indoors – When not in use, mower

should be stored indoors in a dry, locked place out of the

reach of children. The start key and battery packs should

also be removed and stored in a separate location out of

the reach of children.



Do not charge battery tool in a damp or wet location.

Do not use, store, or charge battery packs or products

in locations where the temperature is less than 50°F or

more than 100°F. Do not store outside or in vehicles.

Follow instructions for lubricating and changing

accessories.

Only allow responsible adults, who are familiar with the

instructions, to operate this machine.

Never operate machine in a closed area.

Never tamper with safety devices. Check for proper op-

eration regularly.

Save these instructions. Refer to them frequently and

use them to instruct others who may use this product. If

you loan someone this tool, loan them these instructions

also.

5 — English

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and understand

operator’s manual before using this product.

Eye Protection

Always wear eye protection with side shields marked to comply

with ANSI Z87.1.

Wet Conditions Alert

Risk of fire and burns. Do not expose battery, battery compartment,

or electronic components to rain, water, or liquids. Close cover

during use. Do not operate on wet ground.

Electric Shock

Failure to use in dry conditions and to observe safe practices can

result in electric shock.

Keep Hands and Feet Away Keep hands and feet away from blade and cutting area.

No Reach Do not reach hands or feet under mower deck.

No Slope

Do not operate on inclines greater than 15º. Mow across the face

of slopes, never up and down.

Keep Children and

Bystanders Away

Keep all children and bystanders at least 100 ft. away.

Ricochet

Thrown objects can ricochet and result in personal injury or prop-

erty damage.

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates a hazardous situation, which, if not avoided, will result in death or

serious injury.

WARNING:

Indicates a hazardous situation, which, if not avoided, could result in death or

serious injury.

CAUTION:

Indicates a hazardous situation, that, if not avoided, may result in minor or

moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates information considered important, but

not related to a potential injury (e.g. messages relating to property damage).

SYMBOLS

6 — English

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Recycle Symbol

This product uses lithium-ion (Li-ion) batteries. Local, state, or

federal laws may prohibit disposal of batteries in ordinary trash.

Consult your local waste authority for information regarding

available recycling and/or disposal options.

Direct Current Type or a characteristic of current

V Volts Voltage

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

hrs Hours Time

SYMBOLS

7 — English

PRODUCT SPECIFICATIONS

Motor ...................................................................................................................................................................... 40 Volt DC

Deck Size

....................................................................................................................................................................... 20 in.

Height Adjustments

........................................................................................................................................1-1/2 in. to 4 in.

Wheel Size

..............................................................................................................................................8 in. front, 10 in. rear

FEATURES

KNOW YOUR LAWN MOWER

See Figure 1.

The safe use of this product requires an understanding of

the information on the product and in this operator’s manual

as well as a knowledge of the project you are attempting.

Before use of this product, familiarize yourself with all op-

erating features and safety rules.

BATTERY COVER

The battery cover protects the battery port from moisture

and debris.

BATTERY STORAGE COMPARTMENT

The battery storage compartment offers a convenient place

for storing your battery or to store an extra battery pack.

GRASS CATCHER

The grass catcher collects grass clippings and prevents

them from being discharged across your lawn as you mow.

NOTE: Mower will not start without the grass catcher or

mulch plug attached.

HEIGHT ADJUSTMENT LEVER

The height adjustment lever provides cutting height

adjustments.

LED HEADLIGHTS

LED headlights are located on the front of the unit to illumi-

nate your path in low light conditions. The lights will operate

continuously whenever the motor is running.

NOTE: If the start button is pressed or the start levers inside

the upper handle are squeezed and released, the headlights

will illuminate for 60 seconds.

MULCHING PLUG

Your mower is equipped with a mulching plug that covers

the rear discharge opening, which allows the mower blade

to cut and recut for finer clippings.

NOTE: Mower will not start without the grass catcher or

mulch plug attached.

SELF-PROPELLED FEATURE

The adaptive self-propelled feature of your mower automati-

cally slows or increases the speed of your mower based on

your pace.

NOTE: The self-propelled feature will only work in the forward

direction. It will not work if you pull the mower towards you.

START BUTTON AND START LEVERS

The start button and the start levers inside the upper handle

are used to start the blades. Squeeze the start levers then

depress the start button to start the blades. Release the start

levers to stop the motor.

NOTE: The blades will also start if the start button is pressed

first and the levers are squeezed after.

START KEY

The start key must be inserted before the mower can be

started.

TILT SENSOR

The tilt sensor causes the motor to stop if the unit is operated

on inclines greater than 45º for more than four seconds. The

sensor also prevents the unit from starting if it is in a vertical

position or tilted at an angle greater than 45º.

8 — English

ASSEMBLY

UNPACKING

This product requires assembly.

 Carefully remove the product and any accessories from

the box. Make sure that all items listed in the packing list

are included.

WARNING:

Do not use this product if any parts on the Packing List

are already assembled to your product when you unpack

it. Parts on this list are not assembled to the product by

the manufacturer and require customer installation. Use

of a product that may have been improperly assembled

could result in serious personal injury.

 Inspect the product carefully to make sure no breakage

or damage occurred during shipping.

 Do not discard the packing material until you have care-

fully inspected and satisfactorily operated the product.

 If any parts are damaged or missing, please call

1-800-860-4050 for assistance.

PACKING LIST

Lawn Mower

Start Key

Grass Catcher Bag and Frame

Mulching Plug

Operator’s Manual

WARNING:

If any parts are damaged or missing, do not operate this

product until the parts are replaced. Use of this product

with damaged or missing parts could result in serious

personal injury.

WARNING:

Do not attempt to modify this product or create acces-

sories not recommended for use with this product. Any

such alteration or modification is misuse and could result

in a hazardous condition leading to possible serious

personal injury.

WARNING:

Do not insert start key or battery pack until assembly is

complete and you are ready to mow. Failure to comply

could result in accidental starting and possible serious

personal injury.

WARNING:

To prevent accidental starting, do not make any adjust-

ments or installations with the start key or battery pack

inserted. Accidental starting of the mower during assem-

bly could result in serious personal injury.

WARNING:

Never operate the mower without the proper safety de-

vices in place and working. Never operate the mower with

damaged safety devices. Operating the mower with miss-

ing or damaged parts can result in serious personal injury.

UNFOLDING AND ADJUSTING THE HANDLE

ASSEMBLY

See Figure 2.

NOTICE:

Do not allow the starter cable to become pinched or

trapped when raising the handle.

To raise the handle assembly:



Pull the handle adjustment knobs out and rotate

90 degrees.

 Raisethehandleassembly.Avoidpinchingortrapping

any cables.



Rotate the knob 90 degrees again to secure handle in

place.

EXTENDING THE UPPER HANDLE

See Figure 3.

 Move both levers to the unlocked position.

 Fully extend the upper handle.

 Move both levers to the locked position to secure the

upper handle in place.

 To retract the upper handle, move both levers to the

unlocked position and push the upper handle into the

lower handle. Move both levers to the locked position to

secure.

ASSEMBLING THE GRASS CATCHER

See Figures 4 - 5.

 Place the grass catcher frame on a flat surface with the

handle facing down.

 Orient the grass catcher bag so the vinyl floor is facing

up, then slide the bag onto the frame. When installing,

allow the frame handle to remain outside the bag and

make sure the bag seams are located at the frame edges.

 Pull the clip over the frame rail to secure in place.

9 — English

WARNING:

Do not allow familiarity with products to make you care-

less. Remember that a careless fraction of a second is

sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1. Failure to do so could result in

objects being thrown into your eyes resulting in possible

serious injury.

WARNING:

Do not use any attachments or accessories not recom-

mended by the manufacturer of this product. The use of

attachments or accessories not recommended can result

in serious personal injury.

WARNING:

Always inspect mower for missing or damaged parts

and blade for damage, uneven, or excessive wear prior

to use. Use of the mower with damaged or missing parts

can result in serious personal injury.

WARNING:

Always remove battery packs and start key from your tool

when you are assembling parts, making adjustments,

cleaning, or when not in use. Following these instructions

will prevent accidental starting that could cause serious

personal injury.

OPERATION

ASSEMBLY

 Lift the bag’s vinyl floor to the top of the frame rail and

secure in place.

 Using the same method, attach the remaining clips on

each side of the bag to the frame rail to secure.

INSTALLING THE GRASS CATCHER (FOR

REAR BAGGING OPERATION)

See Figures 6 - 7.

NOTE: When using the grass catcher, do not install the

mulching plug.

 Remove the start key and battery pack.

 Place the grass catcher onto the mower so the opening

on the grass catcher covers the rear discharge opening

and the grass catcher’s metal locks are inside the slots

on the mower housing.

 Gently push down on the grass catcher to ensure the

metal locks are fully seated in the slots. The mower will

not start if the metal locks are not fully seated.

 Reinstall the start key and battery pack when you are

ready to mow.

INSTALLING THE MULCHING PLUG

(FOR MULCHING OPERATION)

See Figure 8.

NOTE: When using the mulching plug, do not install the

grass catcher.

 Remove the start key and battery pack.

 Insert the mulching plug into the mower’s rear discharge

opening and place the mulching plug’s metal lock into

the slot on the right side of the mower housing.

 Gently push down on the mulching plug to ensure the

metal lock is fully seated in the slot. The mower will not

start if the metal lock is not fully seated.

 Reinstall the start key and battery pack when you are

ready to mow.

SETTING BLADE HEIGHT

See Figure 9.

When shipped, the blade on the mower is set to a low- cutting

position. Before using the mower for the first time, raise the

cutting position to the height best suited for your lawn. The

average lawn should be between 1-1/2 in. to 2 in. during cool

months and between 2 in. and 3-1/4 in. during hot months.

To adjust the blade height:

 Remove start key and battery pack.

 To raise the blade height, grasp the height adjustment

lever and move it toward the back of the mower.

 To lower the blade height, grasp the height adjustment

lever and move it toward the front of the mower.

 Reinstall start key and battery pack when you are ready

to mow.

10 — English

NOTICE:

Before each use, inspect the entire product for damaged,

missing, or loose parts such as screws, nuts, bolts, caps,

etc. Tighten securely all fasteners and caps and do not

operate this product until all missing or damaged parts

are replaced. Please contact customer service or an

authorized service center for assistance.

APPLICATIONS

You may use this product for the purpose listed below:

Mowing your lawn

WARNING:

With the exception of using the self-propelled feature to

relocate the mower to the mowing site, always remove

battery packs and start key when moving or transporting

the mower to avoid accidental starting that could result

in serious personal injury.

INSTALLING/REMOVING BATTERY PACK

See Figure 10.

 Raise the battery cover.

 Align raised ribs on battery pack with grooves in the bat-

tery port and install the battery pack into the mower.

WARNING:

Make sure the latch on the bottom of the battery pack

snaps in place and the battery pack is fully seated and

secure in the mower’s battery port before beginning op-

eration. Failure to securely seat the battery pack could

cause the battery pack to fall out, resulting in serious

personal injury.

 Lower the battery cover and make sure it is securely

closed.

To remove battery pack:

 Raise the battery cover.

 Press and hold the battery latch button at the bottom of

the battery pack.

 Remove battery pack from the mower.

 Lower the battery cover and make sure it is securely

closed.

For complete charging instructions, refer to the Operator’s

Manuals for your RYOBI battery pack and charger models.

WARNING:

To avoid accidental starting that could result in serious

personal injury, always remove the start key when moving

or transporting the mower.

NOTE: The battery storage compartment offers a convenient

place for storing your battery, or to store an extra battery

pack. The unit cannot be powered by the battery while it

is installed in the battery storage compartment; it must be

moved to the battery port in order to power the unit from

the battery port.

STARTING/STOPPING THE MOWER

See Figures 11 - 12.

NOTE: Mower will not start without the grass catcher or

mulch plug attached, the start key installed, and the battery

in the unit.

Unfold the handle assembly and extend the upper handle

as described earlier.

NOTE: The mower will not start if the handle assembly

is not in the operating position.

Raise the battery cover.

Install the battery pack into the rear battery port.

Insert the start key into the slot beside the battery storage

compartment.

 Lower the battery cover and make sure it is securely

closed.

Squeeze and hold the start levers inside the upper handle.

Press and release the start button to start the blades.

NOTE: The blades will also start if the start button is

pressed first and the levers are squeezed after.

To stop the mower, release the start levers.

NOTE: The blade is disengaged each time the start levers

are released.

SELF-PROPELLED MOWING

See Figure 13.

WARNING:

Never engage the blades when transporting the mower

from one location to another. Only engage the blades by

pressing the start button when you are ready to mow.

Failure to follow these instructions can result in serious

personal injury.

Move the handle lock to the unlocked position.

NOTE: The self-propelled feature will not engage unless

the handle lock is in the unlocked position. To operate

the mower manually, move the handle lock to the locked

position, start the mower, and push the mower forward.

Squeeze and hold the start levers inside the upper handle.

Press and release the start button to start the blades.

Once the mower has been started, the self-propelled

feature is engaged by pushing the upper handle forward.

OPERATION

11 — English

NOTE: The self-propelled feature can be used without

engaging the blade to power the mower from one location

to another. You must move the handle lock to the unlocked

position, squeeze and hold the start levers inside the up-

per handle, and then push the upper handle forward. If

the mower is powered and the blade is already engaged,

completely release the start levers and then squeeze and

hold the start levers again.

MOWING TIPS

WARNING:

Do not mow on wet grass, which can cause you to slip

and fall and result in possible serious personal injury.

NOTE: Fully charge battery before each use for optimal

runtime.

Make sure the lawn is clear of stones, tree nuts, sticks,

wires, and other objects that could damage the lawn mower

blades or motor. Do not mow over property stakes or other

metal posts. Such objects could damage the blade or be

accidentally thrown by the mower in any direction and

cause serious personal injury to the operator and others.

For a healthy lawn, always cut off one-third or less of the

total length of the grass.

When cutting heavy grass, reduce walking speed to allow

for more effective cutting and a proper discharge of the

clippings.

Do not cut wet grass. It will stick to the underside of the

deck and prevent proper bagging or mulching of grass

clippings.

New or thick grass may require a narrower cut or a higher

cutting height.

Clean the underside of the mower deck after each use

to remove grass clippings, leaves, dirt, and any other

accumulated debris.

NOTE: Always stop mower, allow blades to completely

stop, remove the start key and remove the battery pack

from the battery port before cleaning underneath the

mower.

OPERATION

SLOPE OPERATION

See Figure 14.

WARNING:

Slopes are a major factor related to slip and fall accidents

that can result in severe injury. Operation on slopes re-

quires extra caution. If you feel uneasy on a slope, do not

mow it. For your safety, do not attempt to mow slopes

greater than 15 degrees.

Mow across the face of slopes, not up and down. Exercise

extreme caution when changing direction on slopes.

NOTE: The mower has an overtilt sensor that will stop

the motor if the unit is operated on inclines greater than

45º for more than four seconds.

Watch for holes, ruts, rocks, hidden objects, or bumps

which can cause you to slip or trip. Tall grass can hide

obstacles. Remove all objects such as rocks, tree limbs,

etc., which could be tripped over or thrown by the blade.

Always be sure of your footing. A slip and fall can cause

serious personal injury. If you feel you are losing your bal-

ance, release the upper blade control lever immediately.

Do not mow near drop-offs, ditches, or embankments;

you could lose your footing or balance.

EMPTYING THE GRASS CATCHER

See Figure 15.

 Stop the mower and allow the blades to completely stop.

 Open the battery cover.

 Remove the start key and battery pack from the battery

port.

 Lift the grass catcher by its handle to remove from mower.

 Empty grass clippings.

 Reinstall the grass catcher as described earlier in this

manual.

 Reinstall the start key and battery pack when you are

ready to mow.

12 — English

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-

based products, penetrating oils, etc., come in contact

with plastic parts. Chemicals can damage, weaken, or

destroy plastic which can result in serious personal injury.

LUBRICATION

All of the bearings in this product are lubricated with a suf-

ficient amount of high grade lubricant for the life of the unit

under normal operating conditions. Therefore, no further

bearing lubrication is required.

WARNING:

Always protect hands by wearing heavy gloves and/or

wrapping the cutting edges of the blade with rags and

other material when performing blade maintenance. Con-

tact with the blade could result in serious personal injury.

REPLACING THE CUTTING BLADE

See Figures 16 - 17.

NOTE: Only use authorized replacement blades.

Stop the motor and remove the start key. Allow blade to

come to a complete stop.

 Remove the battery pack from the battery port.

Turn the mower on its side.

Wedge a block of wood between the blade and mower

deck to prevent the blade from turning.

Loosen the blade nut by turning it counterclockwise (as

viewed from bottom of mower) using a 15 mm wrench

or socket (not provided).

Remove the blade nut, spacer, blade insulator, and blade.

Place the new blade on the shaft against the blade posts.

Ensure blade is properly seated with shaft going through

center blade hole and the two blade posts inserted into

their respective holes on the blade. Make sure it is installed

with the curved ends pointing up toward the mower deck

and not down toward the ground. When seated properly,

the blade should be flat.

Replace the blade insulator and spacer, then thread the

blade nut on the shaft and finger tighten.

NOTE: Make certain all parts are replaced in the exact

order in which they were removed.

Torque the blade nut down clockwise using a torque

wrench (not provided) to ensure the bolt is properly

tightened. The recommended torque for the blade nut is

310 – 360 in.lbs.

WARNING:

Before performing any maintenance or cleaning the lawn

mower, make sure the mower blades come to a complete

stop and the batteries and start key are removed to avoid

accidental starting and possible serious personal injury.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1. Failure to do so could result in

objects being thrown into your eyes resulting in possible

serious injury.

WARNING:

When servicing, use only authorized replacement parts.

Use of any other parts can create a hazard or cause

product damage.

WARNING:

Never use a hose, water, or any liquids to clean or

rinse off the lawn mower. Corrosive liquids, water, fer-

tilizers, and chemicals used to treat lawns can enter the

lawn mower and/or battery compartment and damage

electronic components and/or the battery pack, which

can result in a short circuit, increased risk of fire, and

serious personal injury. Remove any buildup of grass

and leaves on or around the mower housing and/or un-

derneath the mower deck. Wipe the mower clean with a

dry cloth occasionally.

NOTICE:

Periodically inspect the entire product for damaged,

missing, or loose parts such as screws, nuts, bolts, caps,

etc. Tighten securely all fasteners and caps and do not

operate this product until all missing or damaged parts

are replaced. Please contact customer service or an

authorized service center for assistance.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use. Use

clean cloths to remove dirt, dust, oil, grease, etc.

MAINTENANCE

13 — English

Inspect moving parts for damage, breakage, and wear.

Have repairs made on any damaged or missing parts.

Check blade for damage, uneven, or excessive wear and

replace blade if these conditions exist.

Store mower indoors in a clean, dry place out of the reach

of children.

• To store the mower in a horizontal position, lower the

handle assembly. Avoid pinching or trapping any cables.

• To store the mower in a vertical position, remove the

grass bag, then lower the handle assembly. Avoid

pinching or trapping any cables. Raise the mower 90°

to rest on its rear support.

NOTE: Make sure the pins on the handle adjustment knobs

are fully locked before attempting to raise the mower to

the standing position.

NOTICE:

Do not allow the starter cable to become pinched or

trapped when lowering the handle.

Do not store near corrosive materials such as fertilizer or

rock salt.

MAINTENANCE

WARNING:

Ensure blade is properly seated and the blade nut is

tightened to the torque specifications above. Failure to

properly attach the blade could cause it to come loose

and result in possible serious personal injury.

STORING THE MOWER

See Figures 18 - 19.

WARNING:

Remove all battery packs from the battery port and bat-

tery storage compartment and start key and store indoors

in a secure and dry location out of the reach of children to

prevent unauthorized use of the lawn mower and possible

serious personal injury.

Before storage, wipe any dirt or debris from the battery

area.

Turn mower on its side and clean grass clippings that

have accumulated on the underside of the mower deck.

Wipe the mower clean with a dry cloth.

Check all nuts, bolts, knobs, screws, fasteners, etc., for

tightness.

14 — English

TROUBLESHOOTING

IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICE DEALER.

PROBLEM POSSIBLE CAUSE SOLUTION

Handle not in position. Handle adjustment knobs and/or handle

lock levers are not secured.

Make sure handle adjustment knobs

are fully seated and handle lock clips

are fully locked.

Mower not starting. Battery is low in charge.

Start key not installed.

Handle assembly is not in operating

position.

Grass catcher, mulch plug, or side dis-

charge accessory not installed correctly.

Charge the battery.

Install start key.

Raise lower and upper handle.

Check that grass catcher, mulch plug,

or side discharge accessory is installed

correctly.

Mower cutting grass unevenly. Lawn is rough or cutting height not set

properly.

Adjust the cutting height.

Mower not mulching properly. Wet grass clippings sticking to the un-

derside of the deck.

Wait until the grass dries before mowing.

Mower hard to push. High grass, rear of mower housing and

blade dragging in heavy grass, or cut-

ting height too low.

Raise cutting height.

Mower not bagging properly. Cutting height set too low.

Grass blocking rear chute of mower.

Raise cutting height.

Stop the motor, remove start key, and

battery. Remove grass catcher bag and

remove the blockage.

Mower vibrating at higher speed. Blade is unbalanced, excessively or

unevenly worn.

Bent motor shaft.

Replace the blade.

Stop the motor, remove start key, and

battery. Inspect for damage. Have re-

paired by an authorized service center

before restarting.

Motor stops while cutting. Cutting height set too low. Raise the cutting height.

This product has a Five-year Limited Warranty for personal,

family, or household use (90 days for business or commercial use).

For warranty details, visit www.ryobitools.com

or call (toll free) 1-800-860-4050.

MAKE THE MOST OF YOUR PURCHASE!

Go to http://register.ryobitools.com and register your new tool on-line.

Your product has been fully tested prior to shipment

to ensure your complete satisfaction.

For any questions about operating or maintaining

your product, call the RYOBI Help Line!

2 — Français

AVERTISSEMENT :

LISEZ ET VEILLEZ À COMPRENDRE TOUTES LES

INSTRUCTIONS. Le non respect des instructions

énumérées ci-dessous et sur la machine pourrait résulter

en un choc électrique, un incendie, et/ou des blessures

sérieuses.

LIRE TOUTES LES INSTRUCTIONS

Cet outil coupant est capable d’amputer des mains et des

pieds et projeter des objets. Le non respect de toutes les

instructions de sécurité pourrait résulter en des blessures

graves ou la mort.

Éviter les environnements dangereux – N’utilisez pas la

tondeuse dans un environnement mouillé ou humide et

ne l’utilisez pas durant la pluie.

Garder les enfants à l’écart – Garder les badauds, enfants

et animaux domestiques à une distance minimum de 30,5

m (100 pi). Arrêter la machine si quelqu’un entre dans la

zone.

Des accidents tragiques peuvent survenir si l’opérateur

n’est pas conscient de la présence des enfants. Les

enfants sont souvent attirés pas la machine et l’activité de

tondaison. Ne prenez jamais pour acquis que les enfants

resteront à l’endroit où vous les avez vus la dernière fois.

• Assurez-vous que les enfants soient éloignés de la zone

de coupe et qu’ils soient supervisés par un adulte autre

que l’opérateur.

• Soyez vigilant et éteignez la tondeuse si un enfant

s’approche.

• Ne permettez jamais à des enfants d’utiliser la machine.

• Redoublez la prudence quand vous vous approchez

des coins, des arbustes, des arbres ou d’autres objets

qui peuvent masquer la présence d’un enfant.

Porter une tenue appropriée – Porter des pantalons

longs, manches longues, des gants épais et des souliers

de protection qui protègeront vos pieds et amélioreront

votre équilibre sur des surfaces glissantes. Ne pas porter

de vêtements amples, bijoux, shorts, sandales et ne pas

travailler pieds nus. Ne porter aucun bijou. Ils peuvent

être pris dans les parties en mouvement.

Ne pas travailler hors de portée – Toujours se tenir bien

campé et en équilibre. Le travail hors de portée risque

de faire perdre l’équilibre.

Ne laissez pas la tondeuse sans surveillance quand elle

est allumée ou une fois la clé de démarrage fixée.

Éloignez les mains et les pieds de la zone de coupe. Tenez

vous éloigné de l’ouverture de décharge en tout temps.

Utilisez la tondeuse seulement à la lumière du jour ou

avec une bonne lumière artificielle.

Porter des lunettes de sécurité – Toujours porter une

protection oculaire munie d’écrans latéraux certifiée

conforme à la norme ANSI Z87.1. Utilisez une masque

faciale si l’utilisation produit de la poussière.

Utilisez l’outil approprié – N’utilisez pas la tondeuse pour

aucune tâche sauf celle pour laquelle elle est conçue.

Ne forcez pas la tondeuse – Elle exécutera le travail mieux

et de façon plus sécuritaire à la vitesse pour laquelle elle

fut conçue.

Ne pas charger le bloc-pile sous la pluie ou dans un

endroit mouillé.

Restez vigilant – Regardez ce que vous faites et utilisez

votre meilleur jugement lorsque vous utilisez la tondeuse.

N’utilisez pas la tondeuse si vous êtes fatigué, contrarié ou

sous influence de drogues, d’alcool ou de médicaments.

Un moment d’inattention pendant l’utilisation de la

tondeuse peut résulter en une blessure grave.

Faire l’entretien de la tondeuse avec soins – Gardez

l’outil en bon état. Assurez-vous que les lames soient

affûtées et que les dispositifs de protections soient en

place et en état de fonctionnement. Remplacer les lames

endommagées ou usées de façon inégale avant d’utiliser

la tondeuse d’obtenir un rendement optimal.

Vérifiez fréquemment si tous les écrous, boulons et vis sont

serrés pour s’assurer que l’équipement est sécuritaire. Les

lames de tondeuse sont tranchantes. Envelopper la lame

ou porter des gants et prendre beaucoup de précautions

lors de l’entretien.

Ne pas jeter le pile au feu. La cellule peut exploser. Vérifier

les codes locaux pour connaître toute instruction spéciale

relative à l’élimination des piles.

Arrêter le moteur, attendre que la lame s’arrête

complètement et retirer la clé de démarrage et bloc-piles

avant de réparation du produit, de nettoyer la tondeuse,

d’enlever le collecteur d’herbe ou retrait du capuchon du

broyeur.

Ne jamais utiliser un boyau, de l’eau ou une autre

liquide pour nettoyer ou rincer la tondeuse. Les

liquides corrosifs, l’eau, l’engrais et les produits chimiques

utilisés pour traiter les pelouses peuvent s’infiltrer dans la

tondeuse et/ou le compartiment de la pile et endommager

les composants électroniques et/ou le bloc-pile, ce qui

peut entraîner un court-circuit, augmenter le risque

d’incendie ou des blessures corporelles graves. Enlever

toute accumulation d’herbes ou de feuilles sur ou autour

du corp de la tondeuse et/ou en dessous de la plateforme

de la tondeuse. Essuyer la tondeuse de temps en temps

avec un linge sec.

Remplacer la lame si elle est pliée ou fissurée. Une

lame déséquilibrée provoque des vibrations qui peuvent

endommager le moteur de l’appareil et provoquer

des blessures. Affûter également les extrémités de la

lame émoussée afin de maintenir l’équilibre. Nettoyer

complètement la lame et vérifier son équilibre en la

INSTRUCTIONS IMPORTANTES CONCERNANT LA SÉCURITÉ

3 — Français

INSTRUCTIONS IMPORTANTES CONCERNANT LA SÉCURITÉ

déposant à l’horizontale et en plaçant l’orifice du centre

sur un petit clou. Le clou doit être placé à l’horizontale.

Si l’une des extrémistes de la lame tourne vers le bas,

enlever un peu de métal de la partie épaisse inférieure de

la lame jusqu’à ce que celle-ci soit équilibrée. Une lame

équilibrée lorsqu’aucune extrémité n’est inclinée.

Toujours, utiliser des dispositifs de protection. N’utilisez

pas la tondeuse sans le collecteur d’herbe ou le capuchon

du broyeur et porte arrière de décharge en place et

fonctionne correctement.

Ne pas ouvrir ou altérer le bloc-piles. L’électrolyte est un

produit corrosif pouvant causer des lésions cutanées ou

oculaires. Il peut être toxique en cas d’ingestion.

Suivez les instructions du fabricant relatives à l’installation

et l’utilisation des accessoires. Utilisez seulement des

accessoires approuvés par le fabricant.

Manipuler les batteries avec soin pour éviter des courts-

circuits avec des objets conducteurs comme des anneaux,

des bracelets et des clés. La batterie ou l’objet conducteur

peuvent surchauffer et causer des brûlures.

Nettoyez la zone de travail avant chaque utilisation.

Enlevez tous les objets tels que les roches, noix d’arbres,

les branches, métal, les fils, les os, les jouets et d’autres

objets qui peuvent être projetés par la lame. Restez en

arrière de la poignée quand le moteur est en marche.

Empêcher les démarrages accidentels. S’assurer que la

gâchette est en position d’arrêt avant d’insérer la bloc

piles, de le ramasser ou de le transporter. Le fait de

transporter un appareil en gardant le doigt sur la gâchette

ou de mettre sous tension un appareil lorsque la gâchette

est en position de marche favorise les accidents.

Lorsque le bloc de batteries n’est pas en usage, le garder

à l’écart d’articles tels qu’attaches trombones, pièces de

monnaie, clous, vis et autres petits objets métalliques

risquant d’établir le contact entre les deux bornes. Le

court-circuitage des bornes peut causer des brûlures ou

un incendie.

En cas d’usage abusif, du liquide peut s’échapper des

batteries. Éviter tout contact avec ce liquide. En cas de

contact accidentel, rincer immédiatement les parties

atteintes avec de l’eau. Si le liquide pénètre dans vos yeux,

il faut aussi consulter un médecin. Le liquide s’échappant

des batteries peut causer des irritations ou des brûlures.

Ne pas utiliser un bloc-piles ou un appareil endommagé

ou modifié. Le bris ou la modification du bloc-piles peut

causer un comportement imprévisible et causer un

incendie, une explosion ou des blessures.

Ne pas exposer le bloc-piles ou l’outil à un feu ou à des

températures excessives. Une exposition à un incendie

ou à une température supérieure à 130 °C (265 °F) peut

provoquer une explosion.

Suivre toutes les instructions afférentes à la recharge

et ne pas recharger le bloc-piles ou l’appareil hors des

températures spécifiées dans les instructions. Une

recharge incorrecte ou hors des températures spécifiées

peut endommager la pile et augmenter les risques de feu.

Ne modifiez pas ou n’essayez jamais de réparer l’appareil

ou le bloc de batterie (selon le cas), sauf comme indiqué

dans les instructions d’utilisation et d’entretien.

Évitez les trous, les ornières, les roches, bornes de

propriété ou d’autres objets cachés. Un terrain accidenté

pourrait provoquer un glissement et vous faire tomber par

accident.

Ne tondez pas près des dépressions, fossés ou des

berges.

Tondez les pentes dans le sens transversal, jamais en

montant ou en descendant. Soyez particulièrement

prudent lors des changements de direction sur les terrains

en pente.

Planifiez le parcours de la tondeuse pour éviter d’éjecter

les matériaux sur les routes, les trottoirs, les passants,

etc. Évitez également d’éjecter les matériaux sur un mur

ou une obstruction ce qui pourrait causer un matériau

d’être projeté par ricochet en direction de l’opérateur.

Ne tondez pas l’herbe mouillée ou sur des pentes

excessivement raides. Une mauvaise position peut vous

faire glisser et tomber par accident. Marchez, ne courez

jamais.

Redoublez la prudence si vous vous approchez des

coins, des arbustes, des arbres ou d’autres objets qui

vous cachent la vue.

Ne tirez jamais la tondeuse vers l’arrière à moins que cela

soit absolument nécessaire. Si vous devez tirer la tondeuse

pour éviter un mur ou une obstruction, commencez par

regarder en bas et en arrière pour ne pas trébucher o

tirando la podadora hacia los pies.

N’éjectez jamais du matériel en direction de quelqu’un.

Évitez d’éjecter le matériel sur un mur ou une obstruction.

Le matériel pourrait être projeté par ricochet en direction

de l’opérateur. Arrêtez la lame quand vous traversez des

surfaces recouvertes de gravier.

Des objets frappés par la lame de la tondeuse peuvent

causer des sérieuses blessures. La pelouse devrait

toujours être examinée attentivement et nettoyée de tout

objet avant la tondaison.

Si la tondeuse frappe un objet étranger, suivez ces étapes:

• Arrêter la tondeuse en relachant l’levier de commande

de la lame, attendre que la lame s’arrête complètement,

puis retirer la clé de démarrage.

• Inspectez attentivement la tondeuse pour desceller les

dommages.

• Remplacer la lame si elle est endommagée de quelque

façon que ce soit Réparez tout dommage avant de

démarrer et de continuer à utiliser la tondeuse.

La page charge ...

Ryobi RY401012 Le manuel du propriétaire

Marque: Ryobi

Modèle: RY401012

Catégorie: Tondeuses à gazon

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Ryobi RY401012 Owner's manual
español: Ryobi RY401012 El manual del propietario

Ryobi RY401012 Le manuel du propriétaire

Ryobi RY401012 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents